Commit Graph

55 Commits

Author SHA1 Message Date
Suresh Siddha a6371f8023 tick: Fix the spurious broadcast timer ticks after resume
During resume, tick_resume_broadcast() programs the broadcast timer in
oneshot mode unconditionally. On the platforms where broadcast timer
is not really required, this will generate spurious broadcast timer
ticks upon resume. For example, on the always running apic timer
platforms with HPET, I see spurious hpet tick once every ~5minutes
(which is the 32-bit hpet counter wraparound time).

Similar to boot time, during resume make the oneshot mode setting of
the broadcast clock event device conditional on the state of active
broadcast users.

Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: svenjoac@gmx.de
Cc: torvalds@linux-foundation.org
Cc: rjw@sisk.pl
Link: http://lkml.kernel.org/r/1334802459.28674.209.camel@sbsiddha-desk.sc.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2012-04-19 21:27:50 +02:00
Thomas Gleixner b9a6a23566 tick: Ensure that the broadcast device is initialized
Santosh found another trap when we avoid to initialize the broadcast
device in the switch_to_oneshot code. The broadcast device might be
still in SHUTDOWN state when we actually need to use it. That
obviously breaks, as set_next_event() is called on a shutdown
device. This did not break on x86, but Suresh analyzed it:

From the review, most likely on Sven's system we are force enabling
the hpet using the pci quirk's method very late. And in this case,
hpet_clockevent (which will be global_clock_event) handler can be
null, specifically as this platform might not be using deeper c-states
and using the reliable APIC timer.

Prior to commit 'fa4da365bc7772c', that handler will be set to
'tick_handle_oneshot_broadcast' when we switch the broadcast timer to
oneshot mode, even though we don't use it. Post commit
'fa4da365bc7772c', we stopped switching the broadcast mode to oneshot
as this is not really needed and his platform's global_clock_event's
handler will remain null. While on my SNB laptop, same is set to
'clockevents_handle_noop' because hpet gets enabled very early. (noop
handler on my platform set when the early enabled hpet timer gets
replaced by the lapic timer).

But the commit 'fa4da365bc7772c' tracked the broadcast timer mode in
the SW as oneshot, even though it didn't touch the HW timer. During
resume however, tick_resume_broadcast() saw the SW broadcast mode as
oneshot and actually programmed the broadcast device also into oneshot
mode. So this triggered the null pointer de-reference after the hpet
wraps around and depending on what the hpet counter is set to. On the
normal platforms where hpet gets enabled early we should be seeing a
spurious interrupt (in my SNB laptop I see one spurious interrupt
after around 5 minutes ;) which is 32-bit hpet counter wraparound
time), but that's a separate issue.

Enforce the mode setting when trying to set an event.

Reported-and-tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: torvalds@linux-foundation.org
Cc: svenjoac@gmx.de
Cc: rjw@sisk.pl
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1204181723350.2542@ionos
2012-04-19 21:27:35 +02:00
Thomas Gleixner b435092f70 tick: Fix oneshot broadcast setup really
Sven Joachim reported, that suspend/resume on rc3 trips over a NULL
pointer dereference. Linus spotted the clockevent handler being NULL.

commit fa4da365b(clockevents: tTack broadcast device mode change in
tick_broadcast_switch_to_oneshot()) tried to fix a problem with the
broadcast device setup, which was introduced in commit 77b0d60c5(
clockevents: Leave the broadcast device in shutdown mode when not
needed).

The initial commit avoided to set up the broadcast device when no
broadcast request bits were set, but that left the broadcast device
disfunctional. In consequence deep idle states which need the
broadcast device were not woken up.

commit fa4da365b tried to fix that by initializing the state of the
broadcast facility, but that missed the fact, that nothing initializes
the event handler and some other state of the underlying clock event
device.

The fix is to revert both commits and make only the mode setting of
the clock event device conditional on the state of active broadcast
users. 

That initializes everything except the low level device mode, but this
happens when the broadcast functionality is invoked by deep idle.

Reported-and-tested-by: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1204181205540.2542@ionos
2012-04-18 14:00:56 +02:00
Suresh Siddha fa4da365bc clockevents: tTack broadcast device mode change in tick_broadcast_switch_to_oneshot()
In the commit 77b0d60c5a,
"clockevents: Leave the broadcast device in shutdown mode when not needed",
we were bailing out too quickly in tick_broadcast_switch_to_oneshot(),
with out tracking the broadcast device mode change to 'TICKDEV_MODE_ONESHOT'.

This breaks the platforms which need broadcast device oneshot services during
deep idle states. tick_broadcast_oneshot_control() thinks that it is
in periodic mode and fails to take proper decisions based on the
CLOCK_EVT_NOTIFY_BROADCAST_[ENTER, EXIT] notifications during deep
idle entry/exit.

Fix this by tracking the broadcast device mode as 'TICKDEV_MODE_ONESHOT',
before leaving the broadcast HW device in shutdown mode if there are no active
requests for the moment.

Reported-and-tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: johnstul@us.ibm.com
Link: http://lkml.kernel.org/r/1334011304.12400.81.camel@sbsiddha-desk.sc.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2012-04-10 11:42:07 +02:00
Suresh Siddha 77b0d60c5a clockevents: Leave the broadcast device in shutdown mode when not needed
Platforms with Always Running APIC Timer doesn't use the broadcast timer
but the kernel is leaving the broadcast timer (HPET in this case)
in oneshot mode.

On these platforms, before the switch to oneshot mode, broadcast device is
actually in shutdown mode. Code checks for empty tick_broadcast_mask and
avoids going into the periodic mode.

During switch to oneshot mode, add the same tick_broadcast_mask checks in the
tick_broadcast_switch_to_oneshot() and avoid the broadcast device going into
the oneshot mode.

Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: john stultz <johnstul@us.ibm.com>
Cc: venki@google.com
Link: http://lkml.kernel.org/r/1320452301.15071.16.camel@sbsiddha-desk.sc.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2012-02-15 15:23:09 +01:00
Thomas Gleixner c1be84309c tick-broadcast: Stop active broadcast device when replacing it
When a better rated broadcast device is installed, then the current
active device is not disabled, which results in two running broadcast
devices.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
2011-12-02 16:06:54 +01:00
Martin Schwidefsky d1748302f7 clockevents: Make minimum delay adjustments configurable
The automatic increase of the min_delta_ns of a clockevents device
should be done in the clockevents code as the minimum delay is an
attribute of the clockevents device.

In addition not all architectures want the automatic adjustment, on a
massively virtualized system it can happen that the programming of a
clock event fails several times in a row because the virtual cpu has
been rescheduled quickly enough. In that case the minimum delay will
erroneously be increased with no way back. The new config symbol
GENERIC_CLOCKEVENTS_MIN_ADJUST is used to enable the automatic
adjustment. The config option is selected only for x86.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: john stultz <johnstul@us.ibm.com>
Link: http://lkml.kernel.org/r/20110823133142.494157493@de.ibm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2011-09-08 11:10:56 +02:00
Thomas Gleixner 250f972d85 Merge branch 'timers/urgent' into timers/core
Reason: Get upstream fixes and kfree_rcu which is necessary for a
follow up patch.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2011-05-20 20:08:05 +02:00
Thomas Gleixner 07f4beb0b5 tick: Clear broadcast active bit when switching to oneshot
The first cpu which switches from periodic to oneshot mode switches
also the broadcast device into oneshot mode. The broadcast device
serves as a backup for per cpu timers which stop in deeper
C-states. To avoid starvation of the cpus which might be in idle and
depend on broadcast mode it marks the other cpus as broadcast active
and sets the brodcast expiry value of those cpus to the next tick.

The oneshot mode broadcast bit for the other cpus is sticky and gets
only cleared when those cpus exit idle. If a cpu was not idle while
the bit got set in consequence the bit prevents that the broadcast
device is armed on behalf of that cpu when it enters idle for the
first time after it switched to oneshot mode.

In most cases that goes unnoticed as one of the other cpus has usually
a timer pending which keeps the broadcast device armed with a short
timeout. Now if the only cpu which has a short timer active has the
bit set then the broadcast device will not be armed on behalf of that
cpu and will fire way after the expected timer expiry. In the case of
Christians bug report it took ~145 seconds which is about half of the
wrap around time of HPET (the limit for that device) due to the fact
that all other cpus had no timers armed which expired before the 145
seconds timeframe.

The solution is simply to clear the broadcast active bit
unconditionally when a cpu switches to oneshot mode after the first
cpu switched the broadcast device over. It's not idle at that point
otherwise it would not be executing that code.

[ I fundamentally hate that broadcast crap. Why the heck thought some
  folks that when going into deep idle it's a brilliant concept to
  switch off the last device which brings the cpu back from that
  state? ]

Thanks to Christian for providing all the valuable debug information!

Reported-and-tested-by: Christian Hoffmann <email@christianhoffmann.info>
Cc: John Stultz <johnstul@us.ibm.com>
Link: http://lkml.kernel.org/r/%3Calpine.LFD.2.02.1105161105170.3078%40ionos%3E
Cc: stable@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2011-05-16 23:35:41 +02:00
Andi Kleen 7372b0b122 clockevents: Move C3 stop test outside lock
Avoid taking broadcast_lock in the idle path for systems where the
timer doesn't stop in C3.

[ tglx: Removed the stale label and added comment ]

Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Dave Kleikamp <dkleikamp@gmail.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: lenb@kernel.org
Cc: paulmck@us.ibm.com
Link: http://lkml.kernel.org/r/%3C20110504234806.GF2925%40one.firstfloor.org%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2011-05-05 17:32:13 +02:00
Linus Torvalds 420c1c572d Merge branch 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (62 commits)
  posix-clocks: Check write permissions in posix syscalls
  hrtimer: Remove empty hrtimer_init_hres_timer()
  hrtimer: Update hrtimer->state documentation
  hrtimer: Update base[CLOCK_BOOTTIME].offset correctly
  timers: Export CLOCK_BOOTTIME via the posix timers interface
  timers: Add CLOCK_BOOTTIME hrtimer base
  time: Extend get_xtime_and_monotonic_offset() to also return sleep
  time: Introduce get_monotonic_boottime and ktime_get_boottime
  hrtimers: extend hrtimer base code to handle more then 2 clockids
  ntp: Remove redundant and incorrect parameter check
  mn10300: Switch do_timer() to xtimer_update()
  posix clocks: Introduce dynamic clocks
  posix-timers: Cleanup namespace
  posix-timers: Add support for fd based clocks
  x86: Add clock_adjtime for x86
  posix-timers: Introduce a syscall for clock tuning.
  time: Splitout compat timex accessors
  ntp: Add ADJ_SETOFFSET mode bit
  time: Introduce timekeeping_inject_offset
  posix-timer: Update comment
  ...

Fix up new system-call-related conflicts in
	arch/x86/ia32/ia32entry.S
	arch/x86/include/asm/unistd_32.h
	arch/x86/include/asm/unistd_64.h
	arch/x86/kernel/syscall_table_32.S
(name_to_handle_at()/open_by_handle_at() vs clock_adjtime()), and some
due to movement of get_jiffies_64() in:
	kernel/time.c
2011-03-15 18:53:35 -07:00
Thomas Gleixner 3a142a0672 clockevents: Prevent oneshot mode when broadcast device is periodic
When the per cpu timer is marked CLOCK_EVT_FEAT_C3STOP, then we only
can switch into oneshot mode, when the backup broadcast device
supports oneshot mode as well. Otherwise we would try to switch the
broadcast device into an unsupported mode unconditionally. This went
unnoticed so far as the current available broadcast devices support
oneshot mode. Seth unearthed this problem while debugging and working
around an hpet related BIOS wreckage.

Add the necessary check to tick_is_oneshot_available().

Reported-and-tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <alpine.LFD.2.00.1102252231200.2701@localhost6.localdomain6>
Cc: stable@kernel.org # .21 ->
2011-02-26 09:45:28 +01:00
Torben Hohn e2830b5c1b time: Make do_timer() and xtime_lock local to kernel/time/
All callers of do_timer() are converted to xtime_update(). The only
users of xtime_lock are in kernel/time/. Make both local to
kernel/time/ and remove them from the global header files.

[ tglx: Reuse tick-internal.h instead of creating another local header
  	file. Massaged changelog ]

Signed-off-by: Torben Hohn <torbenh@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: johnstul@us.ibm.com
Cc: yong.zhang0@gmail.com
Cc: hch@infradead.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2011-01-31 19:26:50 +01:00
Uwe Kleine-König 698f93159a fix comment/printk typos concerning "already"
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-07-11 21:45:40 +02:00
Thomas Gleixner b5f91da0a6 clockevents: Convert to raw_spinlock
Convert locks which cannot be sleeping locks in preempt-rt to
raw_spinlocks.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
2009-12-14 23:55:34 +01:00
Suresh Siddha f833bab87f clockevent: Prevent dead lock on clockevents_lock
Currently clockevents_notify() is called with interrupts enabled at
some places and interrupts disabled at some other places.

This results in a deadlock in this scenario.

cpu A holds clockevents_lock in clockevents_notify() with irqs enabled
cpu B waits for clockevents_lock in clockevents_notify() with irqs disabled
cpu C doing set_mtrr() which will try to rendezvous of all the cpus.

This will result in C and A come to the rendezvous point and waiting
for B. B is stuck forever waiting for the spinlock and thus not
reaching the rendezvous point.

Fix the clockevents code so that clockevents_lock is taken with
interrupts disabled and thus avoid the above deadlock.

Also call lapic_timer_propagate_broadcast() on the destination cpu so
that we avoid calling smp_call_function() in the clockevents notifier
chain.

This issue left us wondering if we need to change the MTRR rendezvous
logic to use stop machine logic (instead of smp_call_function) or add
a check in spinlock debug code to see if there are other spinlocks
which gets taken under both interrupts enabled/disabled conditions.

Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: "Pallipadi Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: "Brown Len" <len.brown@intel.com>
LKML-Reference: <1250544899.2709.210.camel@sbs-t61.sc.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2009-08-19 18:15:10 +02:00
Dmitri Vorobiev a52f5c5620 clockevents: tick_broadcast_device can become static
The variable tick_broadcast_device is not used outside of the
file where it is defined, so let's make it static.

Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2009-05-02 10:31:14 +02:00
Rusty Russell 5db0e1e9e0 cpumask: replace for_each_cpu_mask_nr with for_each_cpu in kernel/time/
Impact: cleanup

Simple replacement, now the _nr is redundant.

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Ingo Molnar <mingo@redhat.com>
2009-01-01 10:12:29 +10:30
Rusty Russell 6b954823c2 cpumask: convert kernel time functions
Impact: Use new APIs

Convert kernel/time functions to use struct cpumask *.

Note the ugly bitmap declarations in tick-broadcast.c.  These should
be cpumask_var_t, but there was no obvious initialization function to
put the alloc_cpumask_var() calls in.  This was safe.

(Eventually 'struct cpumask' will be undefined for CONFIG_CPUMASK_OFFSTACK,
so we use a bitmap here to show we really mean it).

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
2009-01-01 10:12:25 +10:30
Rusty Russell 320ab2b0b1 cpumask: convert struct clock_event_device to cpumask pointers.
Impact: change calling convention of existing clock_event APIs

struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.

Another single-patch change.  For safety, we BUG_ON() in
clockevents_register_device() if it's not set.

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
2008-12-13 21:20:26 +10:30
Thomas Gleixner fb02fbc14d NOHZ: restart tick device from irq_enter()
We did not restart the tick device from irq_enter() to avoid double
reprogramming and extra events in the return immediate to idle case.

But long lasting softirqs can lead to a situation where jiffies become
stale:

idle()
  tick stopped (reprogrammed to next pending timer)
  halt()
   interrupt
     jiffies updated from irq_enter()
     interrupt handler
     softirq function 1 runs 20ms
     softirq function 2 arms a 10ms timer with a stale jiffies value
     jiffies updated from irq_exit()
     timer wheel has now an already expired timer
     (the one added in function 2)
     timer fires and timer softirq runs

This was discovered when debugging a timer problem which happend only
when the ath5k driver is active. The debugging proved that there is a
softirq function running for more than 20ms, which is a bug by itself.

To solve this we restart the tick timer right from irq_enter(), but do
not go through the other functions which are necessary to return from
idle when need_resched() is set.

Reported-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Elias Oltmanns <eo@nebensachen.de>
2008-10-17 18:13:38 +02:00
Thomas Gleixner 07454bfff1 clockevents: check broadcast tick device not the clock events device
Impact: jiffies increment too fast.

Hugh Dickins noted that with NOHZ=n and HIGHRES=n jiffies get
incremented too fast. The reason is a wrong check in the broadcast
enter/exit code, which keeps the local apic timer in periodic mode
when the switch happens.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-10-04 10:51:07 +02:00
Thomas Gleixner 27ce4cb4a0 clockevents: prevent mode mismatch on cpu online
Impact: timer hang on CPU online observed on AMD C1E systems

When a CPU is brought online then the broadcast machinery can
be in the one shot state already. Check this and setup the timer 
device of the new CPU in one shot mode so the broadcast code
can pick up the next_event value correctly.

Another AMD C1E oddity, as we switch to broadcast immediately and
not after the full bring up via the ACPI cpu idle code.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-09-23 11:38:53 +02:00
Thomas Gleixner 302745699c clockevents: check broadcast device not tick device
Impact: Possible hang on CPU online observed on AMD C1E machines.

The broadcast setup code looks at the mode of the tick device to
determine whether it needs to be shut down or setup. This is wrong
when the broadcast mode is set to one shot already. This can happen
when a CPU is brought online as it goes through the periodic setup
first.

The problem went unnoticed as sane systems do not call into that code
before the switch to one shot for the clock event device happens.
The AMD C1E idle routine switches over immediately and thereby shuts
down the just setup device before the first interrupt happens.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-09-23 11:38:53 +02:00
Thomas Gleixner 2344abbcbd clockevents: make device shutdown robust
The device shut down does not cleanup the next_event variable of the
clock event device. So when the device is reactivated the possible
stale next_event value can prevent the device to be reprogrammed as it
claims to wait on a event already.

This is the root cause of the resurfacing suspend/resume problem,
where systems need key press to come back to life.

Fix this by setting next_event to KTIME_MAX when the device is shut
down. Use a separate function for shutdown which takes care of that
and only keep the direct set mode call in the broadcast code, where we
can not touch the next_event value.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-09-16 13:47:02 -07:00
Thomas Gleixner 7300711e8c clockevents: broadcast fixup possible waiters
Until the C1E patches arrived there where no users of periodic broadcast
before switching to oneshot mode. Now we need to trigger a possible
waiter for a periodic broadcast when switching to oneshot mode.
Otherwise we can starve them for ever.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-09-06 07:21:17 +02:00
Thomas Gleixner 1fb9b7d29d clockevents: prevent endless loop lockup
The C1E/HPET bug reports on AMDX2/RS690 systems where tracked down to a
too small value of the HPET minumum delta for programming an event.

The clockevents code needs to enforce an interrupt event on the clock event
device in some cases. The enforcement code was stupid and naive, as it just
added the minimum delta to the current time and tried to reprogram the device.
When the minimum delta is too small, then this loops forever.

Add a sanity check. Allow reprogramming to fail 3 times, then print a warning
and double the minimum delta value to make sure, that this does not happen again.
Use the same function for both tick-oneshot and tick-broadcast code.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-09-05 11:11:53 +02:00
Thomas Gleixner 9c17bcda99 clockevents: prevent multiple init/shutdown
While chasing the C1E/HPET bugreports I went through the clock events
code inch by inch and found that the broadcast device can be initialized
and shutdown multiple times. Multiple shutdowns are not critical, but
useless waste of time. Multiple initializations are simply broken. Another
CPU might have the device in use already after the first initialization and
the second init could just render it unusable again.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-09-05 11:11:52 +02:00
Thomas Gleixner d4496b3955 clockevents: prevent endless loop in periodic broadcast handler
The reprogramming of the periodic broadcast handler was broken,
when the first programming returned -ETIME. The clockevents code
stores the new expiry value in the clock events device next_event field
only when the programming time has not been elapsed yet. The loop in
question calculates the new expiry value from the next_event value
and therefor never increases.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-09-05 11:11:51 +02:00
Ingo Molnar 82638844d9 Merge branch 'linus' into cpus4096
Conflicts:

	arch/x86/xen/smp.c
	kernel/sched_rt.c
	net/iucv/iucv.c

Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-07-16 00:29:07 +02:00
Ingo Molnar 1a781a777b Merge branch 'generic-ipi' into generic-ipi-for-linus
Conflicts:

	arch/powerpc/Kconfig
	arch/s390/kernel/time.c
	arch/x86/kernel/apic_32.c
	arch/x86/kernel/cpu/perfctr-watchdog.c
	arch/x86/kernel/i8259_64.c
	arch/x86/kernel/ldt.c
	arch/x86/kernel/nmi_64.c
	arch/x86/kernel/smpboot.c
	arch/x86/xen/smp.c
	include/asm-x86/hw_irq_32.h
	include/asm-x86/hw_irq_64.h
	include/asm-x86/mach-default/irq_vectors.h
	include/asm-x86/mach-voyager/irq_vectors.h
	include/asm-x86/smp.h
	kernel/Makefile

Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-07-15 21:55:59 +02:00
Thomas Gleixner aa276e1caf x86, clockevents: add C1E aware idle function
C1E on AMD machines is like C3 but without control from the OS. Up to
now we disabled the local apic timer for those machines as it stops
when the CPU goes into C1E. This excludes those machines from high
resolution timers / dynamic ticks, which hurts especially X2 based
laptops.

The current boot time C1E detection has another, more serious flaw
as well: some BIOSes do not enable C1E until the ACPI processor module
is loaded. This causes systems to stop working after that point.

To work nicely with C1E enabled machines we use a separate idle
function, which checks on idle entry whether C1E was enabled in the
Interrupt Pending Message MSR. This allows us to do timer broadcasting
for C1E and covers the late enablement of C1E as well.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-07-08 07:47:18 +02:00
Jens Axboe 8691e5a8f6 smp_call_function: get rid of the unused nonatomic/retry argument
It's never used and the comments refer to nonatomic and retry
interchangably. So get rid of it.

Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-06-26 11:24:35 +02:00
Mike Travis cad0e458d1 clocksource/events: use performance variant for_each_cpu_mask_nr
Change references from for_each_cpu_mask to for_each_cpu_mask_nr
where appropriate

Reviewed-by: Paul Jackson <pj@sgi.com>
Reviewed-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-23 18:39:06 +02:00
Glauber Costa 833df317f9 clockevents: fix typo in tick-broadcast.c
braodcast -> broadcast

Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-04-21 07:59:51 +02:00
Russell King d7b906897e [S390] genirq/clockevents: move irq affinity prototypes/inlines to interrupt.h
> Generic code is not supposed to include irq.h. Replace this include
> by linux/hardirq.h instead and add/replace an include of linux/irq.h
> in asm header files where necessary.
> This change should only matter for architectures that make use of
> GENERIC_CLOCKEVENTS.
> Architectures in question are mips, x86, arm, sh, powerpc, uml and sparc64.
>
> I did some cross compile tests for mips, x86_64, arm, powerpc and sparc64.
> This patch fixes also build breakages caused by the include replacement in
> tick-common.h.

I generally dislike adding optional linux/* includes in asm/* includes -
I'm nervous about this causing include loops.

However, there's a separate point to be discussed here.

That is, what interfaces are expected of every architecture in the kernel.
If generic code wants to be able to set the affinity of interrupts, then
that needs to become part of the interfaces listed in linux/interrupt.h
rather than linux/irq.h.

So what I suggest is this approach instead (against Linus' tree of a
couple of days ago) - we move irq_set_affinity() and irq_can_set_affinity()
to linux/interrupt.h, change the linux/irq.h includes to linux/interrupt.h
and include asm/irq_regs.h where needed (asm/irq_regs.h is supposed to be
rarely used include since not much touches the stacked parent context
registers.)

Build tested on ARM PXA family kernels and ARM's Realview platform
kernels which both use genirq.

[ tglx@linutronix.de: add GENERIC_HARDIRQ dependencies ]

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
2008-04-17 07:47:05 +02:00
Thomas Gleixner 186e3cb8a4 timer: clean up tick-broadcast.c
clean up tick-broadcast.c

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-01-30 13:30:01 +01:00
Thomas Gleixner cdc6f27d9e clockevents: fix reprogramming decision in oneshot broadcast
Resolve the following regression of a choppy, almost unusable laptop:

 http://lkml.org/lkml/2007/12/7/299
 http://bugzilla.kernel.org/show_bug.cgi?id=9525

A previous version of the code did the reprogramming of the broadcast
device in the return from idle code. This was removed, but the logic in
tick_handle_oneshot_broadcast() was kept the same.

When a broadcast interrupt happens we signal the expiry to all CPUs
which have an expired event. If none of the CPUs has an expired event,
which can happen in dyntick mode, then we reprogram the broadcast
device. We do not reprogram otherwise, but this is only correct if all
CPUs, which are in the idle broadcast state have been woken up.

The code ignores, that there might be pending not yet expired events on
other CPUs, which are in the idle broadcast state. So the delivery of
those events can be delayed for quite a time.

Change the tick_handle_oneshot_broadcast() function to check for CPUs,
which are in broadcast state and are not woken up by the current event,
and enforce the rearming of the broadcast device for those CPUs.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2007-12-18 18:05:58 +01:00
Li Zefan 8dce39c231 time: fix inconsistent function names in comments
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-11-05 15:12:33 -08:00
Thomas Gleixner 3dfbc88464 x86: C1E late detection fix. Really switch off lapic timer
Doh, I completely missed that devices marked DUMMY are not running
the set_mode function. So we force broadcasting, but we keep the
local APIC timer running.

Let the clock event layer mark the device _after_ switching it off.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2007-10-17 20:15:13 +02:00
Avi Kivity bf020cb7b3 time: simplify smp_call_function_single() call sequence
smp_call_function_single() now knows how to call the function on the
current cpu.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-17 08:42:48 -07:00
Thomas Gleixner 1595f452f3 clockevents: introduce force broadcast notifier
The 64bit SMP bootup is slightly different to the 32bit one. It enables
the boot CPU local APIC timer before all CPUs are brought up. Some AMD C1E
systems have the C1E feature flag only set in the secondary CPU. Due to
the early enable of the boot CPU local APIC timer the APIC timer is
registered as a fully functional device. When we detect the wreckage during
the bringup of the secondary CPU, we need to force the boot CPU into
broadcast mode. 

Add a new notifier reason and implement the force broadcast in the clock
events layer.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2007-10-14 22:57:45 +02:00
Venki Pallipadi 4a93232dab clock events: allow replacement of broadcast timer
Change the broadcast timer, if a timer with higher rating becomes available.

Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2007-10-12 23:04:23 +02:00
Thomas Gleixner c8a1d398de clockevents: fix periodic broadcast for oneshot devices
The next_event member of the clock event device is used to keep track
of the next periodic event. For one shot only devices it is wrong to
clear the variable, as the next event will be based on it.

Pointed out by Ralf Baechle

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
2007-10-12 23:04:06 +02:00
Thomas Gleixner b7e113dc9d clockevents: remove the suspend/resume workaround^Wthinko
In a desparate attempt to fix the suspend/resume problem on Andrews
VAIO I added a workaround which enforced the broadcast of the oneshot
timer on resume. This was actually resolving the problem on the VAIO
but was just a stupid workaround, which was not tackling the root
cause: the assignement of lower idle C-States in the ACPI processor_idle
code. The cpuidle patches, which utilize the dynamic tick feature and
go faster into deeper C-states exposed the problem again. The correct
solution is the previous patch, which prevents lower C-states across
the suspend/resume.

Remove the enforcement code, including the conditional broadcast timer
arming, which helped to pamper over the real problem for quite a time.
The oneshot broadcast flag for the cpu, which runs the resume code can
never be set at the time when this code is executed. It only gets set,
when the CPU is entering a lower idle C-State.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-09-22 17:15:34 -07:00
Thomas Gleixner 31d9b3938c clockevents: do not shutdown the oneshot broadcast device
When a cpu goes offline it is removed from the broadcast masks. If the
mask becomes empty the code shuts down the broadcast device. This is
wrong, because the broadcast device needs to be ready for the online
cpu going idle (into a c-state, which stops the local apic timer).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2007-09-16 15:36:43 +02:00
Thomas Gleixner 07eec6af44 clockevents: Enforce oneshot broadcast when broadcast mask is set on resume
The jinxed VAIO refuses to resume without hitting keys on the keyboard
when this is not enforced. It is unclear why the cpu ends up in a lower
C State without notifying the clock events layer, but enforcing the
oneshot broadcast here is safe.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2007-09-16 15:36:43 +02:00
Thomas Gleixner 5590a536c0 clockevents: fix device replacement
When a device is replaced by a better rated device, then the broadcast
mode needs to be evaluated again. When the new device has no requirement
for broadcasting, then the broadcast bits for the CPU must be cleared.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-21 17:49:15 -07:00
Thomas Gleixner 18de5bc4c1 clockevents: fix resume logic
We need to make sure, that the clockevent devices are resumed, before
the tick is resumed. The current resume logic does not guarantee this.

Add CLOCK_EVT_MODE_RESUME and call the set mode functions of the clock
event devices before resuming the tick / oneshot functionality.

Fixup the existing users.

Thanks to Nigel Cunningham for tracking down a long standing thinko,
which affected the jinxed VAIO.

[akpm@linux-foundation.org: xen build fix]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-21 17:49:15 -07:00
Thomas Gleixner 72fcde9662 Ignore bogus ACPI info for offline CPUs
Booting a SMP kernel with maxcpus=1 on a SMP system leads to a hard hang,
because ACPI ignores the maxcpus setting and sends timer broadcast info for
the offline CPUs.  This results in a stuck for ever call to
smp_call_function_single() on an offline CPU.

Ignore the bogus information and print a kernel error to remind ACPI
folks to fix it.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-23 20:14:11 -07:00