Add support for the ab9540 variant of the ab8500 family.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Avinash Kumar <avinash.kumar@stericsson.com>
Cc: Thirupathi Chippakurthy <thirupathi.chippakurthy@stericsson.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for the ab8540 variant of the ab8500 family.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Avinash Kumar <avinash.kumar@stericsson.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Introduce a "flags" field in "struct ab8500_usb" to allow controlling
driver features and quirks depending on ab8500 chip variant and
revision.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move each chip's PHY tuning value set code to a separate function to
improve code readability.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add an initial platform_device_id table to the ab8500-usb driver to
allow probing additional variants of the ab8500 family chips.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The driver supports both ab8500 and ab8505, but the actual phy tuning
values logic sets ab8500 values:
if (!is_ab8500_2p0_or_earlier(ab->ab8500))
which is supposed to set values for ab8500, but incorrectly results true
for ab8505 too.
Fix this by adding an additional is_ab8500(ab->ab8500) check.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add an ab8500_usb_restart_phy() function called during probe to ensure
that the AB8500 USB phy is initialized properly even when a cable is
connected at probe time.
Without this fix subsequent host reconnections are not detected
properly.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Sakethram Bommisetti <sakethram.bommisetti@stericsson.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Various non functional coding style fixes on ux500_dma.c and
phy-ab8500-usb.c drivers.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since regulator_enable() is going to be marked as __must_check in the
next merge window, always check regulator_enable() return value and
print a warning if it fails.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Modify ab8500_usb_set_peripheral() and ab8500_usb_set_host() code to
schedule phy_dis_work only when necessary in order to prevent regulator
count mismatch during reboot/shutdown.
Signed-off-by: Sakethram Bommisetti <sakethram.bommisetti@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ab8500_usb_delayed_work was implemented as a workaroud for the internal
only and now unsupported v1.0 version of AB850. This patch removes the
delayed work and just leave a link status update call at probe time.
Signed-off-by: Sakethram Bommisetti <sakethram.bommisetti@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Amend the ab8500-usb driver to optionally take a pin control handle and
set the state of the pins to "default" on ab8500_usb_phy_enable and to
"sleep" on ab8500_usb_phy_disable.
The pinctrl handle is released on ab8500_usb_phy_disable because USB
pins are shared with ab8505_micro_usb_iddet driver.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix last ab->phy.notifier call to use vbus_draw as notifier argument, as
that's used in ab8500_charger to control charging current.
Also drop a related TODO comment, and the additional
ux500_musb_set_vbus(musb, 0), as with this patch it was causing an
erratic behaviour of gadget ep0 state machine.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To prevent clock and regulator frameworks from complaining, only disable
the host or peripheral phy if they were enabled.
Reported-by: Sakethram Bommisetti <sakethram.bommisetti@stericsson.com>
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add ab8500_usb_regulator_{enable,disable} functions to control USB phy
regulators on corresponding ab8500_usb_phy_{enable,disable} events.
This contains some workaround and optimization for specific AB8500
versions.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Sakethram Bommisetti <sakethram.bommisetti@stericsson.com>
Signed-off-by: Praveena Nadahally <praveen.nadahally@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Split ab8500_usb_phy_ctrl into separate enable/disable functions to make
the code more linear and readable.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
AB8500 v2.0 has eye diagram issues when drawing more than 100mA from
VBUS. Force charging current to 100mA in case of standard host.
Signed-off-by: Sakethram Bommisetti <sakethram.bommisetti@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Set phy tuning values proposed by the hardware teams for AB8500 and
AB8505 to improve USB eye diagram performances.
Signed-off-by: Sakethram Bommisetti <sakethram.bommisetti@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert local data allocation to devm_kzalloc and drop unnecessary fail
path code.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Update irq handling code to notify all possible link status changes of
AB8500 and AB8505 to the ux500-musb glue driver. The additional event
codes will be used for pm-runtime implementation, and are defined in a
separate ux500-specific header.
This also modify the irq registration code to use devm_* helpers and
drop all non necessary fail path code.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
AB8500 versions preceding 2.0 were only used internally by ST-Ericsson
and are not supported anymore. This patch drops all v1.0 and v1.1
support code.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this will make sure that we have sensible names
for all phy drivers. Current situation was already
quite bad with too generic names being used.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fabio Baltieri
Sakethram Bommisetti
Mian Yousaf Kaukab
Sachin Kamat
Patrice Chotard
Felipe Balbi