Commit Graph

68 Commits

Author SHA1 Message Date
Robert Hancock 8959d300a7 sata_nv: fix ATAPI issues with memory over 4GB (v7)
This fixes some problems with ATAPI devices on nForce4 controllers in ADMA mode
on systems with memory located above 4GB. We need to delay setting the 64-bit
DMA mask until the PRD table and padding buffer are allocated so that they don't
get allocated above 4GB and break legacy mode (which is needed for ATAPI
devices). Also, if either port is in ATAPI mode we need to set the DMA mask
for the PCI device to 32-bit to ensure that the IOMMU code properly bounces
requests above 4GB, as it appears setting the bounce limit does not guarantee
that we will not try to map requests above this point.

Reported to fix https://bugzilla.redhat.com/show_bug.cgi?id=351451

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-06 07:00:27 -05:00
Robert Hancock a1fe782414 sata_nv: fix for completion handling
This patch is based on an original patch from Kuan Luo of NVIDIA,
posted under subject "fixed a bug of adma in rhel4u5 with HDS7250SASUN500G".
His description follows. I've reworked it a bit to avoid some unnecessary
repeated checks but it should be functionally identical.

"The patch is to solve the error message "ata1: CPB flags CMD err,
flags=0x11" when testing HDS7250SASUN500G in rhel4u5.
I tested this hd in 2.6.24-rc7 which needed to remove the mask in
blacklist to run the ncq and the same error also showed up.

I traced the  bug and found that the interrupt finished a command (for
example, tag=0) when the driver got that adma status is
NV_ADMA_STAT_DONE  and  cpb->resp_flags is NV_CPB_RESP_DONE.
However, For this hd, the drive maybe didn't clear bit 0 at this moment.
It meaned the hardware  had not completely finished the command.
If at the same time  the driver freed the command(tag 0) and sended
another command (tag 0), the error happened.

The notifier register is 32-bit register containing notifier value.
Value is bit vector containing one bit per tag number (0-31) in
corresponding bit positions (bit 0 is for tag 0, etc). When bit is set
then ADMA indicates that command with corresponding tag number completed
execution.

So i added the check notifier code. Sometimes i saw that the notifier
reg set some bits  , but the adma status set NV_ADMA_STAT_CMD_COMPLETE
,not NV_ADMA_STAT_DONE. So i added the NV_ADMA_STAT_CMD_COMPLETE check
code."

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-01 12:26:38 -05:00
Tejun Heo ff2aeb1eb6 libata: convert to chained sg
libata used private sg iterator to handle padding sg.  Now that sg can
be chained, padding can be handled using standard sg ops.  Convert to
chained sg.

* s/qc->__sg/qc->sg/

* s/qc->pad_sgent/qc->extra_sg[]/.  Because chaining consumes one sg
  entry.  There need to be two extra sg entries.  The renaming is also
  for future addition of other extra sg entries.

* Padding setup is moved into ata_sg_setup_extra() which is organized
  in a way that future addition of other extra sg entries is easy.

* qc->orig_n_elem is unused and removed.

* qc->n_elem now contains the number of sg entries that LLDs should
  map.  qc->mapped_n_elem is added to carry the original number of
  mapped sgs for unmapping.

* The last sg of the original sg list is used to chain to extra sg
  list.  The original last sg is pointed to by qc->last_sg and the
  content is stored in qc->saved_last_sg.  It's restored during
  ata_sg_clean().

* All sg walking code has been updated.  Unnecessary assertions and
  checks for conditions the core layer already guarantees are removed.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:14 -05:00
Robert Hancock 3f3debdbfb sata_nv: don't use legacy DMA in ADMA mode (v3)
We need to run any DMA command with result taskfile requested in ADMA mode
when the port is in ADMA mode, otherwise it may try to use the legacy DMA engine
in ADMA mode which is not allowed. Enforce this with BUG_ON() since data
corruption could potentially result if this happened. Also, fail any attempt to
try and issue NCQ commands with result taskfile requested, since the hardware
doesn't allow this.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-04 14:01:18 -05:00
Fernando Luis Vázquez Cao 647c595dad nv_hardreset: update dangling reference to bugzilla entry
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-08 13:08:40 -05:00
Jeff Garzik 360737a982 [libata] sata_nv: fix SWNCQ enabling
Adapted from patches by Kuan Lou @ NVIDIA and Bartlomiej Zolnierkiewicz.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-29 06:49:24 -04:00
Jeff Garzik 5796d1c4c8 [libata] Address some checkpatch-spotted issues
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-29 06:15:27 -04:00
Jeff Garzik b447916e2b [libata] fix 'if(' and similar areas that lack whitespace
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-29 06:15:27 -04:00
Kuan Luo e2e031eb09 [libata] sata_nv: SWNCQ should not apply to MCP61
The mcp61 has bug with ncq.

Signed-off-by: Kuan Luo <kluo@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-25 02:14:17 -04:00
Jeff Garzik 2dcb407e61 [libata] checkpatch-inspired cleanups
Tackle the relatively sane complaints of checkpatch --file.

The vast majority is indentation and whitespace changes, the rest are

* #include fixes
* printk KERN_xxx prefix addition
* BSS/initializer cleanups

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-23 20:59:42 -04:00
Kuan Luo f140f0f12f [libata] sata_nv: add SW NCQ support for MCP51/MCP55/MCP61
Add the Software NCQ support to sata_nv.c for MCP51/MCP55/MCP61 SATA
controller.  NCQ function is disable by default, you can enable it
with 'swncq=1'.  NCQ will be turned off if the drive is Maxtor on
MCP51 or MCP55 rev 0xa2 platform.

[akpm@linux-foundation.org: build fix]
Signed-off-by: Kuan Luo <kluo@nvidia.com>
Signed-off-by: Peer Chen <pchen@nvidia.com>
Cc: Zoltan Boszormenyi <zboszor@dunaweb.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-15 15:16:53 -04:00
Tejun Heo 31cc23b349 libata-pmp-prep: implement ops->qc_defer()
Controllers which support PMP have various restrictions on which
combinations of commands are allowed to what number of devices
concurrently.  This patch implements ops->qc_defer() which determines
whether a qc can be issued at the moment or should be deferred.

If the function returns ATA_DEFER_LINK, the qc will be deferred until
a qc completes on the link.  If ATA_DEFER_PORT, until a qc completes
on any link.  The defer conditions are advisory and in general
ATA_DEFER_LINK can be considered as lower priority deferring than
ATA_DEFER_PORT.

ops->qc_defer() replaces fixed ata_scmd_need_defer().  For standard
NCQ/non-NCQ exclusion, ata_std_qc_defer() is implemented.  ahci and
sata_sil24 are converted to use ata_std_qc_defer().

ops->qc_defer() is heavier than the original mechanism because full qc
is prepped before determining to defer it, but various information is
needed to determine defer conditinos and fully translating a qc is the
only way to supply such information in generic manner.

IMHO, this shouldn't cause any noticeable performance issues as

* for most cases deferring occurs rarely (except for NCQ-aware
  cmd-switching PMP)
* translation itself isn't that expensive
* once deferred the command won't be repeated until another command
  completes which usually is a very long time cpu-wise.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:41 -04:00
Jeff Garzik ac8869d56d [libata] Remove ->port_disable() hook
It was always set to ata_port_disable().  Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:35 -04:00
Jeff Garzik 6d32d30f55 [libata] Remove ->irq_ack() hook, and ata_dummy_irq_on()
* ->irq_ack() is redundant to what the irq handler already
  performs... chk-status + irq-clear.  Furthermore, it is only
  called in one place, when screaming-irq-debugging is enabled,
  so we don't want to bother with a hook just for that.

* ata_dummy_irq_on() is only ever used in drivers that have
  no callpath reaching ->irq_on().  Remove .irq_on hook from
  those drivers, and the now-unused ata_dummy_irq_on()

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:34 -04:00
Tejun Heo 0c88758b5a libata-link: make two port flags HRST_TO_RESUME and SKIP_D2H_BSY link flags
HRST_TO_RESUME and SKIP_D2H_BSY are link attributes.  Move them to
ata_link->flags.  This will allow host and PMP links to have different
attributes.  ata_port_info->link_flags is added and used by LLDs to
specify these flags during initialization.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:31 -04:00
Tejun Heo cc0680a580 libata-link: linkify reset
Make reset methods and related functions deal with ata_link instead of
ata_port.

* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functions

This patch introduces no behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:31 -04:00
Tejun Heo 9af5c9c97d libata-link: introduce ata_link
Introduce ata_link.  It abstracts PHY and sits between ata_port and
ata_device.  This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port.  Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.

This patch only defines the host link.  Multiple link handling will be
added later.  Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.

This patch introduces no behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:30 -04:00
Jeff Garzik 2a3103ce43 [libata] Bump driver versions
Bump the versions for drivers that were modified, but had not already
had a version number bump.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-31 04:54:06 -04:00
Tejun Heo da3dbb17a0 libata: make ->scr_read/write callbacks return error code
Convert ->scr_read/write callbacks to return error code to better
indicate failure.  This will help handling of SCR_NOTIFICATION.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20 08:02:11 -04:00
Tejun Heo b64bbc39f2 libata: improve EH report formatting
Requiring LLDs to format multiple error description messages properly
doesn't work too well.  Help LLDs a bit by making ata_ehi_push_desc()
insert ", " on each invocation.  __ata_ehi_push_desc() is the raw
version without the automatic separator.

While at it, make ehi_desc interface proper functions instead of
macros.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20 08:02:11 -04:00
Tejun Heo d583bc1881 libata: simplify PCI legacy SFF host handling
With PCI resource fix up for legacy hosts.  We can use the same code
path to allocate IO resources and initialize host for both legacy and
native SFF hosts.  Only IRQ requesting needs to be different.

Rename ata_pci_*_native_host() to ata_pci_*_sff_host(), kill all
legacy specific functions and use the renamed functions instead.  This
simplifies code a lot.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-10 21:27:09 -04:00
Jeff Garzik 531e3a61f5 [libata] sata_nv: undo merge error
Only the ADMA entry was supposed to be able to change queue depth.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-02 18:12:19 -04:00
Robert Hancock 1e0b5ab81e sata_nv: allow changing queue depth
The sata_nv driver was missing the change_queue_depth hook in the SCSI host
template which the other NCQ-capable libata drivers had. This made it impossible
to change the queue depth by user request. Add this in.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-02 10:14:02 -04:00
Jeff Garzik 8bc3fc470e libata: bump versions
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-21 20:26:38 -04:00
Jeff Garzik a617c09f6d libata: Trim trailing whitespace
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-21 20:14:23 -04:00
Tejun Heo 1daf9ce74e sata_nv: fix fallout of devres conversion
As with all other drivers, sata_nv's hpriv is allocated with
devm_kzalloc() and there's no need to free it explicitly.  Kill
nv_remove_one() which incorrectly used kfree() instead of devm_kfree()
and use ata_pci_remove_one() directly.

Original fix is from Peer Chen.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-17 20:57:10 -04:00
Peer Chen 074b8ba386 drivers/ata: remove the wildcard from sata_nv driver
Because nvidia SATA controllers onward base on AHCI, so wildcard in sata_nv
driver is unnecessary.  Also the wildcard sometimes cause sata_nv driver to
be loaded for AHCI controllers,which is not as expected.

Signed-off-by: Peer Chen <pchen@nvidia.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-17 20:57:10 -04:00
Tejun Heo 1626aeb881 libata: clean up SFF init mess
The intention of using port_mask in SFF init helpers was to eventually
support exoctic configurations such as combination of legacy and
native port on the same controller.  This never became actually
necessary and the related code always has been subtly broken one way
or the other.  Now that new init model is in place, there is no reason
to make common helpers capable of handling all corner cases.  Exotic
cases can simply dealt within LLDs as necessary.

This patch removes port_mask handling in SFF init helpers.  SFF init
helpers don't take n_ports argument and interpret it into port_mask
anymore.  All information is carried via port_info.  n_ports argument
is dropped and always two ports are allocated.  LLD can tell SFF to
skip certain port by marking it dummy.  Note that SFF code has been
treating unuvailable ports this way for a long time until recent
breakage fix from Linus and is consistent with how other drivers
handle with unavailable ports.

This fixes 1-port legacy host handling still broken after the recent
native mode fix and simplifies SFF init logic.  The following changes
are made...

* ata_pci_init_native_host() and ata_init_legacy_host() both now try
  to initialized whatever they can and mark failed ports dummy.  They
  return 0 if any port is successfully initialized.

* ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't
  take n_ports argument.  All info should be specified via port_info
  array.  Always two ports are allocated.

* ata_pci_init_bmdma() exported to be used by LLDs in exotic cases.

* port_info handling in all LLDs are standardized - all port_info
  arrays are const stack variable named ppi.  Unless the second port
  is different from the first, its port_info is specified as NULL
  (tells libata that it's identical to the last non-NULL port_info).

* pata_hpt37x/hpt3x2n: don't modify static variable directly.  Make an
  on-stack copy instead as ata_piix does.

* pata_uli: It has 4 ports instead of 2.  Don't use
  ata_pci_prepare_native_host().  Allocate the host explicitly and use
  init helpers.  It's simple enough.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-11 18:09:18 -04:00
Tejun Heo 9666f4009c libata: reimplement suspend/resume support using sdev->manage_start_stop
Reimplement suspend/resume support using sdev->manage_start_stop.

* Device suspend/resume is now SCSI layer's responsibility and the
  code is simplified a lot.

* DPM is dropped.  This also simplifies code a lot.  Suspend/resume
  status is port-wide now.

* ata_scsi_device_suspend/resume() and ata_dev_ready() removed.

* Resume now has to wait for disk to spin up before proceeding.  I
  couldn't find easy way out as libata is in EH waiting for the
  disk to be ready and sd is waiting for EH to complete to issue
  START_STOP.

* sdev->manage_start_stop is set to 1 in ata_scsi_slave_config().
  This fixes spindown on shutdown and suspend-to-disk.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-11 18:01:03 -04:00
Robert Hancock 53014e2526 sata_nv: fix ADMA freeze/thaw/irq_clear issues
This patch fixes some problems with ADMA-capable controllers with
regard to freeze, thaw and irq_clear libata callbacks. Freeze and
thaw didn't switch the ADMA-specific interrupts on or off, and more
critically the irq_clear function didn't respect the restriction that
the notifier clear registers for both ports have to be written at
the same time even when only one port is being cleared. This could
result in timeouts on one port when error handling (i.e. as a result
of hotplug) occurred on the other port.

As well, this fixes some issues in the interrupt handler: we shouldn't
check any ADMA status if the port has ADMA switched off because of
an ATAPI device, and it also checks to see if any ADMA interrupt has
been raised even when we are in port-register mode.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-09 20:15:46 -04:00
Tejun Heo d4b2bab4f2 libata: add deadline support to prereset and reset methods
Add @deadline to prereset and reset methods and make them honor it.
ata_wait_ready() which directly takes @deadline is implemented to be
used as the wait function.  This patch is in preparation for EH timing
improvements.

* ata_wait_ready() never does busy sleep.  It's only used from EH and
  no wait in EH is that urgent.  This function also prints 'be
  patient' message automatically after 5 secs of waiting if more than
  3 secs is remaining till deadline.

* ata_bus_post_reset() now fails with error code if any of its wait
  fails.  This is important because earlier reset tries will have
  shorter timeout than the spec requires.  If a device fails to
  respond before the short timeout, reset should be retried with
  longer timeout rather than silently ignoring the device.

  There are three behavior differences.

  1. Timeout is applied to both devices at once, not separately.  This
     is more consistent with what the spec says.

  2. When a device passes devchk but fails to become ready before
     deadline.  Previouly, post_reset would just succeed and let
     device classification remove the device.  New code fails the
     reset thus causing reset retry.  After a few times, EH will give
     up disabling the port.

  3. When slave device passes devchk but fails to become accessible
     (TF-wise) after reset.  Original code disables dev1 after 30s
     timeout and continues as if the device doesn't exist, while the
     patched code fails reset.  When this happens, new code fails
     reset on whole port rather than proceeding with only the primary
     device.

  If the failing device is suffering transient problems, new code
  retries reset which is a better behavior.  If the failing device is
  actually broken, the net effect is identical to it, but not to the
  other device sharing the channel.  In the previous code, reset would
  have succeeded after 30s thus detecting the working one.  In the new
  code, reset fails and whole port gets disabled.  IMO, it's a
  pathological case anyway (broken device sharing bus with working
  one) and doesn't really matter.

* ata_bus_softreset() is changed to return error code from
  ata_bus_post_reset().  It used to return 0 unconditionally.

* Spin up waiting is to be removed and not converted to honor
  deadline.

* To be on the safe side, deadline is set to 40s for the time being.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-01 07:49:53 -04:00
Tejun Heo 9a829ccfc8 libata: convert ata_pci_init_native_mode() users to new init model
Convert drivers which use ata_pci_init_native_mode() to new init
model.  ata_pci_init_native_host() is used instead.  sata_nv, sata_uli
and sata_sis are in this category.

Tested on nVidia Corporation CK804 Serial ATA Controller [10de:0054]
in both BMDMA and ADMA mode.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 14:16:03 -04:00
Robert Hancock f2fb344bea sata_nv: don't read shadow registers when in ADMA mode
Reading from the ATA shadow registers while we are in ADMA mode may cause
undefined behavior.  Don't read the ATA status register when completing
commands for this reason, it shouldn't be needed as the controller will
notify us if the command failed.  Also, don't allow commands with result
taskfile requested to execute in ADMA mode, since that requires accessing
the shadow registers.  We also still need to override tf_read since libata
will read the result taskfile on a command failure, and we need to go into
port register mode before allowing this.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 14:16:00 -04:00
Robert Hancock 8ba5e4cbe4 sata_nv: revert use of notifiers for now
Commit 721449bf0d added support for using the
ADMA notifier bits to determine which commands to check for completion.
However there have been reports that this causes command timeouts in certain
cases. This is still being investigated. In addition, apparently the notifiers
won't work if ADMA is disabled on the other port as a result of an ATAPI device
being connected, and we don't handle this case properly.

For now, just restore the previous behavior of checking all active commands
to see if they are complete, without relying on the notifiers.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-09 08:41:16 -05:00
Tejun Heo 438ac6d5e3 libata: add missing CONFIG_PM in LLDs
Add missing #ifdef CONFIG_PM conditionals around all PM related parts
in libata LLDs.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-02 18:30:35 -05:00
Jeff Garzik a84471fe26 [libata] Trim trailing whitespace.
No code changes.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-26 05:51:33 -05:00
Robert Hancock 2a54cf76d1 sata_nv: complain on spurious completion notifiers
Recently Tejun wrote a patch to ahci.c to make it raise a HSM violation
if the drive attempted to complete a tag that wasn't outstanding. We could
run into the same problem with sata_nv ADMA. This adds code to raise a HSM
violation error if the controller gives us a notifier tag that isn't
outstanding, since the drive may be issuing spurious completions.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-23 05:37:11 -05:00
Robert Hancock f5ecac2d8e sata_nv: kill old private BMDMA helper functions
sata_nv implemented its own copies of the BMDMA helper functions for ADMA,
since the ADMA BMDMA status registers are PIO while the other registers
are MMIO, and this was the only way to handle this previously. Now that
we have iomap support, the standard routines should just work, so use them.
The only thing we need to override as far as ADMA and BMDMA is the
post_internal_cmd callback, where we should only call ata_post_internal_cmd
if we are in port-register mode.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-23 05:37:11 -05:00
Robert Hancock 5ce0cf6faf sata_nv: enable hotplug interrupt and fix some readl/readw mismatches
We already have code that handles hotplug interrupt indications in ADMA
mode, this turns on the control flag that actually enables these interrupts.
Also fixes some cases in the same functions where a 16-bit register was read
using a readl instead of a readw.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-21 04:58:19 -05:00
Robert Hancock 721449bf0d sata_nv: Use notifier for completion checks
The hardware provides us a notifier register that indicates what command
tags have completed. Use this to determine which CPBs to check, rather
than blindly checking all active CPBs. This should provide a minor
performance win, since if the controller has touched some of these
incomplete CPBs, accessing them will likely result in a cache miss.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-21 04:58:19 -05:00
Robert Hancock ac3d6b869f sata_nv: Cleanup taskfile setup
This edits the taskfile setup to more closely match the way that libata
sends the taskfile for other controllers. This avoids putting taskfile writes
into the CPB buffer that are not needed according to the taskfile flags.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-21 04:58:19 -05:00
Robert Hancock 41949ed5c1 sata_nv: cleanup CPB and APRD initialization
Clean up the initialization of the CPB and APRD structures so that we
strictly follow the rules for ordering of writes to the CPB flags and
response flags, and prevent duplicate initialization.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-21 04:58:19 -05:00
Robert Hancock 08af741478 sata_nv: Add CPB register info to error_handler output
When error handling occurs with pending commands, output the contents
of the next CPB count and next CPB index registers as well as the others,
since these may be useful for debugging.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-21 04:58:19 -05:00
Robert Hancock 5e5c74a5e1 sata_nv: delay on switching between NCQ and non-NCQ commands
This patch appears to solve some problems with commands timing out in
cases where an NCQ command is immediately followed by a non-NCQ command
(or possibly vice versa). This is a rather ugly solution, but until we
know more about why this is needed, this is about all we can do.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-21 04:58:18 -05:00
Robert Hancock 2cb27853b7 sata_nv: add back some verbosity into ADMA error_handler
Some debug output in the ADMA error_handler function was removed recently,
but it may be useful in certain cases, like NCQ commands timing out. Add it
back in, but make it a bit more intelligent so that it only prints if
command(s) are active and only prints the CPBs for those commands.
That way it won't spew at inappropriate times like suspend/resume.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-21 04:58:17 -05:00
Robert Hancock 5278b50cea sata_nv: handle SError status indication
ADMA-capable controllers provide a bit in the status register that appears
to indicate that the controller detected an SError condition. Update sata_nv
to detect this and trigger error handling in order to handle the fault.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-15 18:05:32 -05:00
Robert Hancock ce053fa8b5 sata_nv: propagate ata_pci_device_do_resume return value
ata_pci_device_do_resume can fail if the PCI device couldn't be re-enabled.
 Update sata_nv to propagate the return value from this call and to not try
to do any other resume activities if it fails.  Fixes a compile warning.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09 17:39:40 -05:00
Robert Hancock a2cfe81a59 sata_nv: wait for response on entering/leaving ADMA mode
Update sata_nv to wait for the controller to indicate via the status
register that it has entered the requested state when switching between
ADMA mode and register mode.  This issue came up recently when debugging
some problems with cache flush command timeouts and while it didn't appear
to fix that problem, this is something we should likely be doing in any
case.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09 17:39:39 -05:00
Robert Hancock 382a6652e9 sata_nv: use ADMA for NODATA commands
Some problems showed up recently with cache flush commands timing out on
sata_nv.  Previously these commands were always handled by transitioning to
legacy mode from ADMA mode first.  The timeout problem was worked around
already by a change to the interrupt handling code for legacy mode, but for
non-data commands like these it appears we can handle them in ADMA mode, so
the switch to legacy mode is not needed.

This patch changes the behavior so that we use ADMA mode to submit
interrupt-driven commands with ATA_PROT_NODATA protocol.  In addition to
avoiding the problem mentioned above entirely, this avoids the overhead of
switching to legacy mode and back to ADMA mode for handling cache flushes.
When handling non-DMA-mapped commands, we leave the APRD blank and clear
the NV_CPB_CTL_APRD_VALID field in the CPB so the controller does not
attempt to read it.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09 17:39:39 -05:00
Robert Hancock 5bd28a4b6e sata_nv: cleanup ADMA error handling
This cleans up a few issues with the error handling in sata_nv in ADMA mode
to make it more consistent with other NCQ-capable drivers like ahci and
sata_sil24:

- When a command failed, we would effectively set AC_ERR_DEV on the
  queued command always.  In the case of NCQ commands this prevents libata
  from doing a log page query to determine the details of the failed
  command, since it thinks we've already analyzed.  Just set flags in the
  port ehi->err_mask, then freeze or abort and let libata figure out what
  went wrong.

- The code handled NV_ADMA_STAT_CPBERR as a "really bad error" which
  caused it to set error flags on every queued command.  I don't know
  exactly what this flag means (no docs, grr!) but from what I can guess
  from the standard ADMA spec, it just means that one or more of the CPBs
  had an error, so we just need to go through and do our normal checks in
  this case.

- In the error_handler function the code would always dump the state of
  all the CPBs.  This output seems redundant at this point since libata
  already dumps the state of all active commands on errors (and it also
  triggers at times when it shouldn't, like when suspending).  Take this
  out.

[akpm@osdl.org: many coding-style fixes]
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Allen Martin <AMartin@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09 17:39:39 -05:00