Signed-off-by: Kornilios Kourtis <kou@zurich.ibm.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Four patches from Or that add Hairpin support to mlx5:
===========================================================
From: Or Gerlitz <ogerlitz@mellanox.com>
We refer the ability of NIC HW to fwd packet received on one port to
the other port (also from a port to itself) as hairpin. The application API
is based
on ingress tc/flower rules set on the NIC with the mirred redirect
action. Other actions can apply to packets during the redirect.
Hairpin allows to offload the data-path of various SW DDoS gateways,
load-balancers, etc to HW. Packets go through all the required
processing in HW (header re-write, encap/decap, push/pop vlan) and
then forwarded, CPU stays at practically zero usage. HW Flow counters
are used by the control plane for monitoring and accounting.
Hairpin is implemented by pairing a receive queue (RQ) to send queue (SQ).
All the flows that share <recv NIC, mirred NIC> are redirected through
the same hairpin pair. Currently, only header-rewrite is supported as a
packet modification action.
I'd like to thanks Elijah Shakkour <elijahs@mellanox.com> for implementing this
functionality
on HW simulator, before it was avail in the FW so the driver code could be
tested early.
===========================================================
From Feras three patches that provide very small changes that allow IPoIB
to support RX timestamping for child interfaces, simply by hooking the mlx5e
timestamping PTP ioctl to IPoIB child interface netdev profile.
One patch from Gal to fix a spilling mistake.
Two patches from Eugenia adds drop counters to VF statistics
to be reported as part of VF statistics in netlink (iproute2) and
implemented them in mlx5 eswitch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaVF5WAAoJEEg/ir3gV/o+fRkH/0PxjwJRA3REqhi/H8HOdH9f
cBLrOzFdqTCYQWQFCLFbMQ/Zgoel3KglpJ0iQMjuVFfjMbybVXOe8FAEVdbWHnfL
C+2HRMe8dplKrsq5UkxJhbyKhFKhl2XeMFYWonw9dSM7Nz5DyowQ1y1r5SgMlMAv
t3mYAIa4kZHK18BjDoIsCoAXXwsHiztR2irMp5+DwataTGP7vC7AsrucDxLA/qFf
I3E15DZk9s1f53PUuY7CYnUnJfMMP3VJdxpyx4k6xt9J2IMuilF4YyD6wpAKsVQU
/LzRkWI9x/6QindffqlrACeeidimOeY4pC4txIhS5uXgFXulugDHq1/Ih1sgZS8=
=g5vr
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-01-08' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-updates-2018-01-08
Four patches from Or that add Hairpin support to mlx5:
===========================================================
From: Or Gerlitz <ogerlitz@mellanox.com>
We refer the ability of NIC HW to fwd packet received on one port to
the other port (also from a port to itself) as hairpin. The application API
is based
on ingress tc/flower rules set on the NIC with the mirred redirect
action. Other actions can apply to packets during the redirect.
Hairpin allows to offload the data-path of various SW DDoS gateways,
load-balancers, etc to HW. Packets go through all the required
processing in HW (header re-write, encap/decap, push/pop vlan) and
then forwarded, CPU stays at practically zero usage. HW Flow counters
are used by the control plane for monitoring and accounting.
Hairpin is implemented by pairing a receive queue (RQ) to send queue (SQ).
All the flows that share <recv NIC, mirred NIC> are redirected through
the same hairpin pair. Currently, only header-rewrite is supported as a
packet modification action.
I'd like to thanks Elijah Shakkour <elijahs@mellanox.com> for implementing this
functionality
on HW simulator, before it was avail in the FW so the driver code could be
tested early.
===========================================================
From Feras three patches that provide very small changes that allow IPoIB
to support RX timestamping for child interfaces, simply by hooking the mlx5e
timestamping PTP ioctl to IPoIB child interface netdev profile.
One patch from Gal to fix a spilling mistake.
Two patches from Eugenia adds drop counters to VF statistics
to be reported as part of VF statistics in netlink (iproute2) and
implemented them in mlx5 eswitch.
Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li says:
====================
code improvements in HNS3 driver
This patchset fixes 2 comments for community review.
[patch 1/2] reverts "net: hns3: Add packet statistics of netdev"
reported by Jakub Kicinski and David Miller.
[patch 2/2] reports the function type the same line with
hns3_nic_get_stats64, reported by Andrew Lunn.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The function type should be on the same line with the function
name, or it may cause display error if a patch edit the
function. There is am example following:
https://www.spinics.net/lists/netdev/msg476141.html
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 8491000754.
It is duplicate to add statistics of netdev for ethtool -S.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
set_fipers() calling should be protected by spinlock in
case that any interrupt breaks related registers setting
and the function we expect. This patch is to move set_fipers()
to spinlock protecting area in ptp_gianfar_adjtime().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcelo Ricardo Leitner says:
====================
sctp: Some sockopt optlen fixes
Hangbin Liu reported that some SCTP sockopt are allowing the user to get
the kernel to allocate really large buffers by not having a ceiling on
optlen.
This patchset address this issue (in patch 2), replace an GFP_ATOMIC
that isn't needed and avoid calculating the option size multiple times
in some setsockopt.
====================
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some sockopt handling functions were calculating the length of the
buffer to be written to userspace and then calculating it again when
actually writing the buffer, which could lead to some write not using
an up-to-date length.
This patch updates such places to just make use of the len variable.
Also, replace some sizeof(type) to sizeof(var).
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu reported that some sockopt calls could cause the kernel to log
a warning on memory allocation failure if the user supplied a large optlen
value. That is because some of them called memdup_user() without a ceiling
on optlen, allowing it to try to allocate really large buffers.
This patch adds a ceiling by limiting optlen to the maximum allowed that
would still make sense for these sockopt.
Reported-by: Hangbin Liu <haliu@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So replace it with GFP_USER and also add __GFP_NOWARN.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jassi Brar says:
====================
Socionext Synquacer NETSEC driver
Changes since v5
# Removed helper macros
# Removed 'inline' qualifier
# Changed multiline empty comment to single line
# Added 'clock-names' property in DT binding example
# Ignore 'clock-names' property in driver until f/ws in the wild are
upgraded or we support instance that take in more than one clock.
# Rebased the patchset onto net-next
Changes since v4
# Fixed ucode indexing as a word, instead of byte
# Removed redundant clocks, keep only phy rate reference clock
and expect it to be 'phy_ref_clk'
Changes since v3
# Discard 'socionext,snq-mdio', and simply use 'mdio' subnode.
# Use ioremap on ucode region as well, instead of memremap.
Changes since v2
# Use 'mdio' subnode in DT bindings.
# Use phy_interface_mode_is_rgmii(), instead of open coding the check.
# Use readl/b with eeprom_base pointer.
# Unregister mdio bus upon failure in probe.
Changes since v1
# Switched from using memremap to ioremap
# Implemented ndo_do_ioctl callback
# Defined optional 'dma-coherent' DT property
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add entry for the Socionext Netsec controller driver and DT bindings.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver adds support for Socionext "netsec" IP Gigabit
Ethernet + PHY IP used in the Synquacer SC2A11 SoC.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds documentation for Device-Tree bindings for the
Socionext NetSec Controller driver.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2018-01-09
This series contains updates to ixgbe and ixgbevf only.
Emil fixes an issue with "wake on LAN"(WoL) where we need to ensure we
enable the reception of multicast packets so that WoL works for IPv6
magic packets. Cleaned up code no longer needed with the update to
adaptive ITR.
Paul update the driver to advertise the highest capable link speed
when a module gets inserted. Also extended the displaying of firmware
version to include the iSCSI and OEM block in the EEPROM to better
identify firmware versions/images.
Tonghao Zhang cleans up a code comment that no longer applies since
InterruptThrottleRate has been removed from the driver.
Alex fixes SR-IOV and MACVLAN offload interaction, where the MACVLAN
offload was incorrectly configuring several filters with the wrong
pool value which resulted in MACLVAN interfaces not being able to
receive traffic that had to pass over the physical interface. Fixed
transmit hangs and dropped receive frames when the number of VFs
changed. Added support for RSS on MACVLAN pools for X550 devices.
Fixed up the MACVLAN limitations so we can now support 63 offloaded
devices. Cleaned up MACVLAN code that is no longer needed with the
recent changes and fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A collection of the last-minute small PCM fixes:
- A workaround for the recent regression wrt PulseAudio
- Removal of spurious WARN_ON() that is triggered by syzkaller
- Fixes for aloop, hardening racy accesses
- Fixes in PCM OSS emulation wrt the unabortable loops that may cause
RCU stall
-----BEGIN PGP SIGNATURE-----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=Fz+p
-----END PGP SIGNATURE-----
Merge tag 'sound-4.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of the last-minute small PCM fixes:
- A workaround for the recent regression wrt PulseAudio
- Removal of spurious WARN_ON() that is triggered by syzkaller
- Fixes for aloop, hardening racy accesses
- Fixes in PCM OSS emulation wrt the unabortable loops that may cause
RCU stall"
* tag 'sound-4.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pcm: Allow aborting mutex lock at OSS read/write loops
ALSA: pcm: Abort properly at pending signal in OSS read/write loops
ALSA: aloop: Fix racy hw constraints adjustment
ALSA: aloop: Fix inconsistent format due to incomplete rule
ALSA: aloop: Release cable upon open error path
ALSA: pcm: Workaround for weird PulseAudio behavior on rewind error
ALSA: pcm: Add missing error checks in OSS emulation plugin builder
ALSA: pcm: Remove incorrect snd_BUG_ON() usages
According to the documentation for Laird SD40 radio modules (which use
the BCM4329 chipset), the order of the Enable_BREAK_To_Host and
Pulsed_HOST_WAKE parameters in the sleep mode struct is reversed
vis-à-vis our struct declaration. See page 46 of this PDF:
http://cdn.lairdtech.com/home/brandworld/files/Application%20Note%20-%2040%20Series%20Bluetooth.pdf
The documentation is dated Oct 2015, so fairly recent, making it appear
more likely that the documentation is correct and our code is wrong.
Amend our code to be in congruence with the documentation.
Cc: Sue White <sue.white@lairdtech.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The driver calls mdelay(15) in the ->suspend, ->resume, ->runtime_suspend
and ->runtime_resume hook, however spinning for such a long period of
time is discouraged as per Documentation/timers/timers-howto.txt.
The use of mdelay() seems unnecessary, it is allowed to sleep in the
system sleep and runtime PM hooks (with the exception of ->suspend_noirq
and ->resume_noirq) and the driver itself also does not rely on a
non-sleeping ->runtime_resume as the only place where a synchronous
resume is performed, in bcm_dequeue(), is called from a work item in
hci_ldisc.c and hci_serdev.c.
So replace the mdelay(15) with msleep(15).
Note that the delay is inserted after asserting or deasserting the
device wake pin, but in bcm_gpio_set_power() that pin is asserted or
deasserted *without* observing a delay. It is thus unclear if the delay
is necessary at all. It is likewise unclear why it is exactly 15 ms,
the commit introducing it, 118612fb91 ("Bluetooth: hci_bcm: Add
suspend/resume PM functions"), does not provide a rationale.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Suggested-and-reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The host wake IRQ is optional, but if none is found, "BCM irq: -22" is
logged which may irritate users. This is really a debug message, so use
dev_dbg() instead of dev_info(). If users are interested in the IRQ,
they can always consult /proc/interrupts.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enable Bluetooth on the following Macs which provide custom ACPI methods
to toggle the GPIOs for device wake and shutdown instead of accessing
the pins directly:
MacBook8,1 2015 12"
MacBook9,1 2016 12"
MacBook10,1 2017 12"
MacBookPro13,1 2016 13"
MacBookPro13,2 2016 13" with Touch Bar
MacBookPro13,3 2016 15" with Touch Bar
MacBookPro14,1 2017 13"
MacBookPro14,2 2017 13" with Touch Bar
MacBookPro14,3 2017 15" with Touch Bar
On the MacBook8,1 Bluetooth is muxed with a second device (a debug port
on the SSD) under the control of PCH GPIO 36. Because serdev cannot
deal with multiple slaves yet, it is currently necessary to patch the
DSDT and remove the SSDC device.
The custom ACPI methods are called:
BTLP (Low Power) takes one argument, toggles device wake GPIO
BTPU (Power Up) tells SMC to drive shutdown GPIO high
BTPD (Power Down) tells SMC to drive shutdown GPIO low
BTRS (Reset) calls BTPD followed by BTPU
BTRB unknown, not present on all MacBooks
Search for the BTLP, BTPU and BTPD methods on ->probe and cache them in
struct bcm_device if the machine is a Mac.
Additionally, set the init_speed based on a custom device property
provided by Apple in lieu of _CRS resources. The Broadcom UART's speed
is fixed on Apple Macs: Any attempt to change it results in Bluetooth
status code 0x0c and bcm_set_baudrate() thus always returns -EBUSY.
By setting only the init_speed and leaving oper_speed at zero, we can
achieve that the host UART's speed is adjusted but the Broadcom UART's
speed is left as is.
The host wake pin goes into the SMC which handles it independently
of the OS, so there's no IRQ for it.
Thanks to Ronald Tschalär who did extensive debugging and testing of
this patch and contributed fixes.
ACPI snippet containing the custom methods and device properties
(taken from a MacBook8,1):
Method (BTLP, 1, Serialized)
{
If (LEqual (Arg0, 0x00))
{
Store (0x01, GD54) /* set PCH GPIO 54 direction to input */
}
If (LEqual (Arg0, 0x01))
{
Store (0x00, GD54) /* set PCH GPIO 54 direction to output */
Store (0x00, GP54) /* set PCH GPIO 54 value to low */
}
}
Method (BTPU, 0, Serialized)
{
Store (0x01, \_SB.PCI0.LPCB.EC.BTPC)
Sleep (0x0A)
}
Method (BTPD, 0, Serialized)
{
Store (0x00, \_SB.PCI0.LPCB.EC.BTPC)
Sleep (0x0A)
}
Method (BTRS, 0, Serialized)
{
BTPD ()
BTPU ()
}
Method (_DSM, 4, NotSerialized) // _DSM: Device-Specific Method
{
If (LEqual (Arg0, ToUUID ("a0b5b7c6-1318-441c-b0c9-fe695eaf949b")))
{
Store (Package (0x08)
{
"baud",
Buffer (0x08)
{ 0xC0, 0xC6, 0x2D, 0x00, 0x00, 0x00, 0x00, 0x00 },
"parity",
Buffer (0x08)
{ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 },
"dataBits",
Buffer (0x08)
{ 0x08, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 },
"stopBits",
Buffer (0x08)
{ 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }
}, Local0)
DTGP (Arg0, Arg1, Arg2, Arg3, RefOf (Local0))
Return (Local0)
}
Return (0x00)
}
Link: https://github.com/Dunedan/mbp-2016-linux/issues/29
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=110901
Reported-by: Leif Liddy <leif.liddy@gmail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Cc: Loic Poulain <loic.poulain@linaro.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Tested-by: Max Shavrick <mxms@me.com> [MacBook8,1]
Tested-by: Leif Liddy <leif.liddy@gmail.com> [MacBook9,1]
Tested-by: Daniel Roschka <danielroschka@phoenitydawn.de> [MacBookPro13,2]
Tested-by: Ronald Tschalär <ronald@innovation.ch> [MacBookPro13,3]
Tested-by: Peter Y. Chuang <peteryuchuang@gmail.com> [MacBookPro14,1]
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A significant portion of this driver lacks error handling. As a first
step, add error paths to bcm_gpio_set_power(), bcm_open(), bcm_close(),
bcm_suspend_device(), bcm_resume_device(), bcm_resume(), bcm_probe() and
bcm_serdev_probe(). (I've also scrutinized bcm_suspend() but think it's
fine as is.)
Those are all the functions accessing the device wake and shutdown GPIO.
On Apple Macs the pins are accessed through ACPI methods, which may fail
for various reasons, hence proper error handling is necessary. Non-Macs
access the pins directly, which may fail as well but the GPIO core does
not yet pass back errors to consumers.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
MacBooks provides custom ACPI methods to toggle the GPIOs for device
wake and shutdown instead of accessing the pins directly. Prepare for
their support by adding callbacks to toggle the GPIOs, which on non-Macs
do nothing more but call gpiod_set_value().
No functional change intended.
Suggested-and-reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If devm_request_irq() fails, the driver bails out of bcm_request_irq()
but continues to ->setup the device (because the IRQ is optional).
The driver subsequently calls devm_free_irq(), enable_irq_wake() and
disable_irq_wake() on the IRQ even though requesting it failed.
Avoid by invalidating the IRQ on request failure.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On ->setup, pm_runtime_enable() is only called if a valid IRQ was found,
but on ->close(), pm_runtime_disable() is called unconditionally.
Disablement of runtime PM is recorded in a counter, so every
pm_runtime_disable() needs to be balanced. Fix it.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Reported-and-reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Upon ->close, the driver powers the Bluetooth controller down, deasserts
the device wake pin, updates the runtime PM status to "suspended" and
finally frees the IRQ.
Because the IRQ is freed last, a runtime resume can take place after
the controller was powered down. The impact is not grave, the worst
thing that can happen is that the device wake pin is reasserted (should
have no effect while the regulator is off) and that setting the runtime
PM status to "suspended" does not reflect reality.
Still, it's wrong, so free the IRQ first.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
pm_runtime_disable() and pm_runtime_set_suspended() are replaced with
empty inlines if CONFIG_PM is disabled, so there's no need to #ifdef
them.
device_init_wakeup() is likewise replaced with an inline, though it's
not empty, but it and devm_free_irq() can be made conditional on
IS_ENABLED(CONFIG_PM), which is preferable to #ifdef as per section 20
of Documentation/process/coding-style.rst.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ->close, ->suspend and ->resume hooks assume presence of a valid IRQ
if the device is wakeup capable. However it's entirely possible that
wakeup was enabled by some other entity besides this driver and in this
case the user will get a WARN splat if no valid IRQ was found. Avoid by
checking if the IRQ is valid, i.e. > 0.
Case in point: On recent MacBook Pros, the Bluetooth device lacks an
IRQ (because host wakeup is handled by the SMC, independently of the
operating system), but it does possess a _PRW method (which specifies
the SMC's GPE as wake event). The ACPI core therefore automatically
marks the physical Bluetooth device wakeup capable upon binding it to
its ACPI companion:
device_set_wakeup_capable+0x96/0xb0
acpi_bind_one+0x28a/0x310
acpi_platform_notify+0x20/0xa0
device_add+0x215/0x690
serdev_device_add+0x57/0xf0
acpi_serdev_add_device+0xc9/0x110
acpi_ns_walk_namespace+0x131/0x280
acpi_walk_namespace+0xf5/0x13d
serdev_controller_add+0x6f/0x110
serdev_tty_port_register+0x98/0xf0
tty_port_register_device_attr_serdev+0x3a/0x70
uart_add_one_port+0x268/0x500
serial8250_register_8250_port+0x32e/0x490
dw8250_probe+0x46c/0x720
platform_drv_probe+0x35/0x90
driver_probe_device+0x300/0x450
bus_for_each_drv+0x67/0xb0
__device_attach+0xde/0x160
bus_probe_device+0x9c/0xb0
device_add+0x448/0x690
platform_device_add+0x10e/0x260
mfd_add_device+0x392/0x4c0
mfd_add_devices+0xb1/0x110
intel_lpss_probe+0x2a9/0x610 [intel_lpss]
intel_lpss_pci_probe+0x7a/0xa8 [intel_lpss_pci]
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
[lukas: fix up ->suspend and ->resume as well, add commit message]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit 0395ffc1ee ("Bluetooth: hci_bcm: Add PM for BCM devices")
amended this driver to request a shutdown and device wake GPIO on probe,
but mandated that only one of them need to be present:
/* Make sure at-least one of the GPIO is defined and that
* a name is specified for this instance
*/
if ((!dev->device_wakeup && !dev->shutdown) || !dev->name) {
dev_err(&pdev->dev, "invalid platform data\n");
return -EINVAL;
}
However the same commit added a call to bcm_gpio_set_power() to the
->probe hook, which unconditionally accesses *both* GPIOs. Luckily,
the resulting NULL pointer deref was never reported, suggesting there's
no machine where either GPIO is missing.
Commit 8a92056837 ("Bluetooth: hci_bcm: Add (runtime)pm support to the
serdev driver") removed the check whether at least one of the GPIOs is
present without specifying a reason.
Because commit 62aaefa7d0 ("Bluetooth: hci_bcm: improve use of gpios
API") refactored the driver to use devm_gpiod_get_optional() instead of
devm_gpiod_get(), one is now tempted to believe that the driver doesn't
require *any* of the two GPIOs.
Which is wrong, the driver still requires both GPIOs to avoid a NULL
pointer deref. To this end, establish the status quo ante and request
the GPIOs with devm_gpiod_get() again. Bail out of ->probe if either
of them is missing.
Oddly enough, whereas bcm_gpio_set_power() accesses the device wake pin
unconditionally, bcm_suspend_device() and bcm_resume_device() do check
for its presence before accessing it. Those checks are superfluous,
so remove them.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Cc: Loic Poulain <loic.poulain@linaro.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Daniel Borkmann says:
====================
pull-request: bpf 2018-01-09
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Prevent out-of-bounds speculation in BPF maps by masking the
index after bounds checks in order to fix spectre v1, and
add an option BPF_JIT_ALWAYS_ON into Kconfig that allows for
removing the BPF interpreter from the kernel in favor of
JIT-only mode to make spectre v2 harder, from Alexei.
2) Remove false sharing of map refcount with max_entries which
was used in spectre v1, from Daniel.
3) Add a missing NULL psock check in sockmap in order to fix
a race, from John.
4) Fix test_align BPF selftest case since a recent change in
verifier rejects the bit-wise arithmetic on pointers
earlier but test_align update was missing, from Alexei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit f11a04464a ("i2c: gpio: Enable working over slow
can_sleep GPIOs"), probing the i2c RTC connected to an i2c-gpio bus on
r8a7740/armadillo fails with:
rtc-s35390a 0-0030: error resetting chip
rtc-s35390a: probe of 0-0030 failed with error -5
More debug code reveals:
i2c i2c-0: master_xfer[0] R, addr=0x30, len=1
i2c i2c-0: NAK from device addr 0x30 msg #0
s35390a_get_reg: ret = -6
Commit 02e479808b ("gpio: Alter semantics of *raw* operations to
actually be raw") moved open drain/source handling from
gpiod_set_raw_value_commit() to gpiod_set_value(), but forgot to take
into account that gpiod_set_value_cansleep() also needs this handling.
The i2c protocol mandates that i2c signals are open drain, hence i2c
communication fails.
Fix this by adding the missing handling to gpiod_set_value_cansleep(),
using a new common helper gpiod_set_value_nocheck().
Fixes: 02e479808b ("gpio: Alter semantics of *raw* operations to actually be raw")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[removed underscore syntax, added kerneldoc]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Jakub Kicinski says:
====================
This series starts with a fix to Jesper's recent work, somehow I forgot
about control rings during review. Second patch is cleaning up a vNIC
header, in kdoc we should not use @ for #define constants. Aligning of
the top of the stack as well as bottom (last bytes will be unused) helps
the performance. We should check offload datapath's max MTU when program
is loaded and we can allow TC hw offload flag to be changed freely while
XDP offload is active.
Next group of patches adds more fully featured relocation support. Due
to limited amount of code space we only load the image to NIC's memory
when program is attached. Since we can't predict which programs are
loaded later, we should translate as if image was to be loaded at offset
zero and only apply relocations at load time. Many more advanced features
(eg. tail class, subprograms, dynamic allocation of program space and
sharing it between ports) will depend on this.
Nic adds support for signed comparison instructions.
Quentin makes use of the verifier log in our driver, the verifier print
function (verbose()) has to be renamed and exported.
v2:
- replace #define by function aliasing for verbose() in patch 13
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Now that `bpf_verifier_log_write()` is exported from the verifier and
makes it possible to reuse the verifier log to print messages to the
standard output, use this instead of the kernel logs in the nfp driver
for printing error messages occurring at verification time.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Rename the BPF verifier `verbose()` to `bpf_verifier_log_write()` and
export it, so that other components (in particular, drivers for BPF
offload) can reuse the user buffer log to dump error messages at
verification time.
Renaming `verbose()` was necessary in order to avoid a name so generic
to be exported to the global namespace. However to prevent too much pain
for backports, the calls to `verbose()` in the kernel BPF verifier were
not changed. Instead, use function aliasing to make `verbose` point to
`bpf_verifier_log_write`. Another solution could consist in making a
wrapper around `verbose()`, but since it is a variadic function, I don't
see a clean way without creating two identical wrappers, one for the
verifier and one to export.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This patch adds signed jump instructions (jsgt, jsge, jslt, jsle)
to the nfp jit. As well as adding the additional required raw
assembler branch mask to nfp_asm.h
Signed-off-by: Nic Viljoen <nick.viljoen@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Instead of having an app callback per message type hand off
all offload-related handling to apps with one "rest of ndo_bpf"
callback.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
To make absolute relocated branches (branches which will be completely
rewritten with br_set_offset()) distinguishable in user space dumps
from normal jumps add a large offset to them.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The translator pre-allocates a buffer of maximal program size.
Due to HW/FW limitations the program buffer can't currently be
longer than 128Kb, so we used to kmalloc() it, and then map for
DMA directly.
Now that the late branch resolution is copying the program image
anyway, we can just kvmalloc() the buffer. While at it, after
translation reallocate the buffer to save space.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Don't translate the program assuming it will be loaded at a given
address. This will be required for sharing programs between ports
of the same NIC, tail calls and subprograms. It will also make the
jump targets easier to understand when dumping the program to user
space.
Translate the program as if it was going to be loaded at address
zero. When load happens add the load offset in and set addresses
of special branches.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In preparation for better handling of relocations move existing
helper for setting branch offset to nfp_asm.c and add two more.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jump target resolution should be in jit.c not offload.c.
No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
TC BPF offload was added first, so we used to assume that
the ethtool TC HW offload flag cannot be touched whenever
any BPF program is loaded on the NIC. This unncessarily
limits changes to the TC flag when offloaded program is XDP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When BPF offload is active we need may need to restrict the MTU
changes more than just to the limitation of the kernel XDP datapath.
Allow the BPF code to veto a MTU change.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Kernel enforces the alignment of the bottom of the stack, NFP
deals with positive offsets better so we should align the top
of the stack. Round the stack size to NFP word size (4B).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
We should use % instead of @ for documenting preprocessor defines.
Add missing documentation of __NFP_REPR_TYPE_MAX. This gets rid
of all remaining kdoc warnings in the driver.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Some RX rings are used for control messages, those will not have
a netdev pointer in dp. Skip XDP rxq handling on those rings.
Fixes: 7f1c684a89 ("nfp: setup xdp_rxq_info")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski says:
====================
Two more trivial fixes to the recent XDP RXQ series.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Looks like commit e817f85652 ("xdp: generic XDP handling of
xdp_rxq_info") replaced kvfree(dev->_rx) in free_netdev() with
a call to netif_free_rx_queues() which doesn't actually free
the rings?
While at it remove the unnecessary temporary variable.
Fixes: e817f85652 ("xdp: generic XDP handling of xdp_rxq_info")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
kvzalloc'ed memory should be kvfree'd.
Fixes: e817f85652 ("xdp: generic XDP handling of xdp_rxq_info")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This contains what I hope are the last RISC-V changes to go into 4.15.
I know it's a bit last minute, but I think they're all fairly small
changes:
* SR_* constants have been renamed to match the latest ISA
specification.
* Some CONFIG_MMU #ifdef cruft has been removed. We've never supported
!CONFIG_MMU.
* __NR_riscv_flush_icache is now visible to userspace. We were hoping
to avoid making this public in order to force userspace to call the
vDSO entry, but it looks like QEMU's user-mode emulation doesn't want
to emulate a vDSO. In order to allow glibc to fall back to a system
call when the vDSO entry doesn't exist we're just
* Our defconfig is no long empty. This is another one that just slipped
through the cracks. The defconfig isn't perfect, but it's at least
close to what users will want for the first RISC-V development board.
Getting closer is kind of splitting hairs here: none of the RISC-V
specific drivers are in yet, so it's not like things will boot out of
the box.
The only one that's strictly necessary is the __NR_riscv_flush_icache
change, as I want that to be part of the public API starting from our
first kernel so nobody has to worry about it. The others are nice to
haves, but they seem sane for 4.15 to me.
-----BEGIN PGP SIGNATURE-----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=PhUK
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-4.15-rc8_cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains what I hope are the last RISC-V changes to go into 4.15.
I know it's a bit last minute, but I think they're all fairly small
changes:
- SR_* constants have been renamed to match the latest ISA
specification.
- Some CONFIG_MMU #ifdef cruft has been removed. We've never
supported !CONFIG_MMU.
- __NR_riscv_flush_icache is now visible to userspace. We were hoping
to avoid making this public in order to force userspace to call the
vDSO entry, but it looks like QEMU's user-mode emulation doesn't
want to emulate a vDSO. In order to allow glibc to fall back to a
system call when the vDSO entry doesn't exist we're just
- Our defconfig is no long empty. This is another one that just
slipped through the cracks. The defconfig isn't perfect, but it's
at least close to what users will want for the first RISC-V
development board. Getting closer is kind of splitting hairs here:
none of the RISC-V specific drivers are in yet, so it's not like
things will boot out of the box.
The only one that's strictly necessary is the __NR_riscv_flush_icache
change, as I want that to be part of the public API starting from our
first kernel so nobody has to worry about it. The others are nice to
haves, but they seem sane for 4.15 to me"
* tag 'riscv-for-linus-4.15-rc8_cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/linux:
riscv: rename SR_* constants to match the spec
riscv: remove CONFIG_MMU ifdefs
RISC-V: Make __NR_riscv_flush_icache visible to userspace
RISC-V: Add a basic defconfig