Commit Graph

12 Commits

Author SHA1 Message Date
Vasanthakumar Thiagarajan b35a51c7dd cfg80211: Make pre-CAC results valid only for ETSI domain
DFS requirement for ETSI domain (section 4.7.1.4 in
ETSI EN 301 893 V1.8.1) is the only one which explicitly
states that once DFS channel is marked as available afer
the CAC, this channel will remain in available state even
moving to a different operating channel. But the same is
not explicitly stated in FCC DFS requirement. Also, Pre-CAC
requriements are not explicitly mentioned in FCC requirement.
Current implementation in keeping DFS channel in available
state is same as described in ETSI domain.

For non-ETSI DFS domain, this patch gives a grace period of 2 seconds
since the completion of successful CAC before moving the channel's
DFS state to 'usable' from 'available' state. The same grace period
is checked against the channel's dfs_state_entered timestamp while
deciding if a DFS channel is available for operation. There is a new
radar event, NL80211_RADAR_PRE_CAC_EXPIRED, reported when DFS channel
is moved from available to usable state after the grace period. Also
make sure the DFS channel state is reset to usable once the beaconing
operation on that channel is brought down (like stop_ap, leave_ibss
and leave_mesh) in non-ETSI domain.

Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-06 13:54:15 +01:00
Michal Kazior f04c22033c cfg80211: export interface stopping function
This exports a new cfg80211_stop_iface() function.

This is intended for driver internal interface
combination management and channel switching.

Due to locking issues (it re-enters driver) the
call is asynchronous and uses cfg80211 event
list/worker.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-05-06 15:16:34 +02:00
Ilan Peer 7c8d5e03ac cfg80211: send stop AP event only due to internal reason
Commit "nl80211: send event when AP operation is stopped" added an
event to notify user space that an AP interface has been stopped, to
handle cases such as suspend etc. The event is sent regardless
if the stop AP flow was triggered by user space or due to internal state
change.

This might cause issues with wpa_supplicant/hostapd flows that consider
stop AP flow as a synchronous one, e.g., AP/GO channel change in the
absence of CSA support. In such cases, the flow will restart the AP
immediately after the stop AP flow is done, and only handle the stop
AP event after the current flow is done, and as a result stop the AP
again.

Change the current implementation to only send the event in case the
stop AP was triggered due to an internal reason.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-02-25 17:34:18 +01:00
Michal Kazior 9e0e29615a cfg80211: consider existing DFS interfaces
It was possible to break interface combinations in
the following way:

 combo 1: iftype = AP, num_ifaces = 2, num_chans = 2,
 combo 2: iftype = AP, num_ifaces = 1, num_chans = 1, radar = HT20

With the above interface combinations it was
possible to:

 step 1. start AP on DFS channel by matching combo 2
 step 2. start AP on non-DFS channel by matching combo 1

This was possible beacuse (step 2) did not consider
if other interfaces require radar detection.

The patch changes how cfg80211 tracks channels -
instead of channel itself now a complete chandef
is stored.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-02-04 21:58:17 +01:00
Johannes Berg 348baf0eac nl80211: send event when AP operation is stopped
There are a few cases, e.g. suspend, where an AP interface is
stopped by the kernel rather than by userspace request, most
commonly when suspending. To let userspace know about this,
send the NL80211_CMD_STOP_AP command as an event every time
an AP interface is stopped. This also happens when userspace
did in fact request the AP stop, but that's not a problem.

For full-MAC drivers this may need to be extended to also
cover cases where the device stopped the AP operation for
some reason, this a bit more complicated because then all
cfg80211 state also needs to be reset; such API is not part
of this patch.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-02-04 21:58:08 +01:00
Kyeyoon Park fa9ffc7456 cfg80211: Add support for QoS mapping
This allows QoS mapping from external networks to be implemented as
defined in IEEE Std 802.11-2012, 10.24.9. APs can use this to advertise
DSCP ranges and exceptions for mapping frames to a specific UP over
Wi-Fi.

The payload of the QoS Map Set element (IEEE Std 802.11-2012, 8.4.2.97)
is sent to the driver through the new NL80211_ATTR_QOS_MAP attribute to
configure the local behavior either on the AP (based on local
configuration) or on a station (based on information received from the
AP).

Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-19 16:29:22 +01:00
Johannes Berg 947add36ca cfg80211: move exported event functions into nl80211
This is the sort of thing gcc's LTO could do, but since
we don't have that yet we can also do it manually. The
advantage is reduced code, both source and binary, e.g.
on x86-64

   text	   data	    bss	    dec	    hex	filename
 442825	  56230	    776	 499831	  7a077	cfg80211.ko (before)
 441585	  56230	    776	 498591	  79b9f	cfg80211.ko (after)

a reduction of ~1k.

But in order to not complicate the code move only those
functions that are simple wrappers, not those that have
functionality of their own.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-06 16:35:46 +01:00
Johannes Berg dfa674da18 cfg80211: move some AP code to right file
Some AP code ended up in mlme.c as ap.c didn't
exist when it was written, move it now.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-03 13:01:40 +01:00
Antonio Quartulli 06e191e22e cfg80211: store the ssid into wirless_dev in AP mode
Store the configured ssid in wdev->ssid when starting an AP

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-07 17:57:14 +01:00
Hila Gonen e35e4d28b6 cfg80211: add wrappers for registered_device_ops
This will allow adding central tracing like in mac80211.

Signed-off-by: Hila Gonen <hila.gonen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-10-18 10:53:37 +02:00
Michal Kazior f4489ebeff cfg80211: add channel tracking for AP and mesh
We need to know which channel is used by a running
AP and mesh for channel context accounting and
finding matching/active interface combination.

STA/IBSS have current_bss already which allows us
to check which channel a vif is tuned to.
Non-fixed channel IBSS can be handled with
additional changes.

Monitor mode is going to be handled differently.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-29 13:39:15 +02:00
Michal Kazior 60771780c2 cfg80211: introduce cfg80211_stop_ap
This functionality will be reused when interface
is going down. Avoids code duplication. Also adds
missing wdev locking.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-06-29 13:39:14 +02:00