Commit Graph

2893 Commits

Author SHA1 Message Date
Linus Torvalds 32250e4a5f Merge branch 'i2c/for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
 "Quite some driver updates:
   - piix4 can now handle multiplexed adapters
   - brcmstb, xlr, eg20t, designware drivers support more SoCs
   - emev2 gained i2c slave support
   - img-scb and rcar got bigger refactoring to remove issues
   - lots of common driver updates

  i2c core changes:
   - new quirk flag when an adapter does not support clock stretching,
     so clients can be configured to avoid that if possible
   - added a helper function to retrieve timing parameters from firmware
     (with rcar being the first user)
   - "multi-master" DT binding added so drivers can adapt to this
     setting (like disabling PM to keep arbitration working)
   - RuntimePM for the logical adapter device is now always enabled by
     the core to ensure propagation from childs to the parent (the HW
     device)
   - new macro builtin_i2c_driver to reduce boilerplate"

* 'i2c/for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (70 commits)
  i2c: create builtin_i2c_driver to avoid registration boilerplate
  i2c: imx: fix i2c resource leak with dma transfer
  dt-bindings: i2c: eeprom: add another EEPROM device
  dt-bindings: move I2C eeprom descriptions to the proper file
  i2c: designware: Do not require clock when SSCN and FFCN are provided
  DT: i2c: trivial-devices: Add Epson RX8010 and MPL3115
  i2c: s3c2410: remove superfluous runtime PM calls
  i2c: always enable RuntimePM for the adapter device
  i2c: designware: retry transfer on transient failure
  i2c: ibm_iic: rename i2c_timings struct due to clash with generic version
  i2c: designware: Add support for AMD Seattle I2C
  i2c: imx: Remove unneeded comments
  i2c: st: use to_platform_device()
  i2c: designware: use to_pci_dev()
  i2c: brcmstb: Adding support for CM and DSL SoCs
  i2c: mediatek: fix i2c multi transfer issue in high speed mode
  i2c: imx: improve code readability
  i2c: imx: Improve message log when DMA is not used
  i2c: imx: add runtime pm support to improve the performance
  i2c: imx: init bus recovery info before adding i2c adapter
  ...
2016-01-14 11:25:37 -08:00
Rafael J. Wysocki 1e3f28a552 Merge branch 'acpi-soc'
* acpi-soc:
  PM / clk: don't leave clocks enabled when driver not bound
  i2c: dw: Add APM X-Gene ACPI I2C device support
  ACPI / APD: Add APM X-Gene ACPI I2C device support
  ACPI / LPSS: change 'does not have' to 'has' in comment
  Revert "dmaengine: dw: platform: provide platform data for Intel"
  dmaengine: dw: return immediately from IRQ when DMA isn't in use
  dmaengine: dw: platform: power on device on shutdown
  ACPI / LPSS: override power state for LPSS DMA device
  ACPI / LPSS: power on when probe() and otherwise when remove()
  ACPI / LPSS: do delay for all LPSS devices when D3->D0
  ACPI / LPSS: allow to use specific PM domain during ->probe()
  Revert "ACPI / LPSS: allow to use specific PM domain during ->probe()"
  device core: add BUS_NOTIFY_DRIVER_NOT_BOUND notification
  x86/platform/iosf_mbi: Remove duplicate definitions

Conflicts:
	drivers/i2c/busses/i2c-designware-platdrv.c
2016-01-12 01:08:47 +01:00
Rafael J. Wysocki 989652871b Merge branch 'device-properties'
* device-properties:
  device property: avoid allocations of 0 length
  device property: the secondary fwnode needs to depend on the primary
  device property: add spaces to PROPERTY_ENTRY_STRING macro
  include/linux/property.h: fix build issues with gcc-4.4.4
  i2c: designware: Convert to use unified device property API
  mfd: intel-lpss: Pass HSUART configuration via properties
  mfd: intel-lpss: Pass SDA hold time to I2C host controller driver
  mfd: intel-lpss: Add support for passing device properties
  mfd: core: propagate device properties to sub devices drivers
  driver core: Do not overwrite secondary fwnode with NULL if it is set
  driver core: platform: Add support for built-in device properties
  device property: Take a copy of the property set
  device property: Fallback to secondary fwnode if primary misses the property
  device property: return -EINVAL when property isn't found in ACPI
  device property: improve readability of macros
  device property: helper macros for property entry creation
  device property: keep single value inplace
  device property: refactor built-in properties support
  device property: rename helper functions
  device property: always check for fwnode type
2016-01-12 01:07:46 +01:00
Gao Pan c552815312 i2c: imx: fix i2c resource leak with dma transfer
In i2c_imx_dma_xfer(), when dmaengine_submit() returns error,
the context goto label err_submit and then return. However, the
memory allocated for txdesc has not been freed yet, which
leads to resource leak.

Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-10 10:10:28 +01:00
Suravee Suthikulpanit b33af11de2 i2c: designware: Do not require clock when SSCN and FFCN are provided
The current driver uses input clock source frequency to calculate
values for [SS|FS]_[HC|LC] registers. However, when booting ACPI, we do not
currently have a good way to provide the frequency information.
Instead, we can leverage the SSCN and FFCN ACPI methods, which can be used
to directly provide these values. So, the clock information should
no longer be required during probing.

However, since clk can be invalid, additional checks must be done where
we are making use of it.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Loc Ho <lho@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-10 09:36:52 +01:00
Wolfram Sang 2fe3e51892 i2c: s3c2410: remove superfluous runtime PM calls
RuntimePM of the adapter device is now taken care of by the core. So, we
can remove these calls.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-10 09:27:53 +01:00
Wolfram Sang 9f924169c0 i2c: always enable RuntimePM for the adapter device
The adapter device is a logical device. Because of that, it already uses
pm_runtime_no_callbacks() in the core. To ensure proper propagation from
the children (i2c devices) to the parent of the adapter (the HW device),
make sure RuntimePM is enabled in any case.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-10 09:27:06 +01:00
Baruch Siach 8d22f30938 i2c: designware: retry transfer on transient failure
Set the i2c_adapter retries field to a sensible value. This allows the i2c core
to retry master_xfer() when it returns -EAGAIN. Currently the i2c-designware
driver returns -EAGAIN only on Tx arbitration failure (DW_IC_TX_ARB_LOST).

Reported-by: Rolland Chau <zourongrong@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-10 09:24:56 +01:00
Loc Ho 04a407f6b1 i2c: dw: Add APM X-Gene ACPI I2C device support
Enable APM X-Gene ACPI I2C device support by adding the
corresponding ACPI ID. The platform ACPI APD corresponding
change is required to provide the proper clock frequency input.

Signed-off-by: Loc Ho <lho@apm.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-01-07 14:11:55 +01:00
Stephen Rothwell f199b2605c i2c: ibm_iic: rename i2c_timings struct due to clash with generic version
Fixes: e1dba01ca6 ("i2c: add generic routine to parse DT for timing information")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-05 02:06:10 +01:00
Suravee Suthikulpanit 90708ce22b i2c: designware: Add support for AMD Seattle I2C
Add device HID AMDI0510 to match the I2C controlers on AMD Seattle platform

Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-04 20:25:01 +01:00
Fabio Estevam 995e68a5ee i2c: imx: Remove unneeded comments
These multi-lines comments do not follow the standard kernel coding
style. In fact, they are not useful comments, so get rid of them.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-04 20:23:33 +01:00
Geliang Tang 66e784130a i2c: st: use to_platform_device()
Use to_platform_device() instead of open-coding it.

Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-03 19:54:31 +01:00
Geliang Tang 238c44a70c i2c: designware: use to_pci_dev()
Use to_pci_dev() instead of open-coding it.

Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-03 19:54:00 +01:00
Kamal Dasu e2e5a2c618 i2c: brcmstb: Adding support for CM and DSL SoCs
Broadcoms DSL, CM (cable modem)and STB I2C core implementation have
8 data in/out registers that can transfer 8 bytes or 32 bytes max.
Cable and DSL "Peripheral" i2c cores use single byte per data
register and the STB can use 4 byte per data register transfer.
Adding support to take care of this difference. Accordingly added
the compatible string for SoCs using the "Peripheral" I2C block.

Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-03 19:50:09 +01:00
Liguo Zhang 8378d01f60 i2c: mediatek: fix i2c multi transfer issue in high speed mode
For mt8173 platform with auto restart support, when doing i2c multi
transfer in high speed, we should ignore the first restart irq after
the master code, otherwise the first transfer will be discarded.

Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Reviewed-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-03 19:38:22 +01:00
Gao Pan e8e712916c i2c: imx: improve code readability
Replace of_get_named_gpio_flags with of_get_named_gpio because
the latter has less parameters, which improves code readability.

Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-03 19:17:29 +01:00
Fabio Estevam 5b66153989 i2c: imx: Improve message log when DMA is not used
When DMA cannot be used, it is better to state that the I2C controller
will operate in PIO mode.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-03 19:11:09 +01:00
Gao Pan 588eb93ea4 i2c: imx: add runtime pm support to improve the performance
In our former i2c driver, i2c clk is enabled and disabled in
xfer function, which contributes to power saving. However,
the clk enable process brings a busy wait delay until the core
is stable. As a result, the performance is sacrificed.

To weigh the power consumption and i2c bus performance, runtime
pm is the good solution for it. The clk is enabled when a i2c
transfer starts, and disabled after a specifically defined delay.

If CONFIG_PM is disabled the net result of this patch is that the
clock is never disabled.

Without the patch the test case (many eeprom reads) executes with approx:
real 1m7.735s
user 0m0.488s
sys 0m20.040s

With the patch the same test case (many eeprom reads) executes with approx:
real 0m54.241s
user 0m0.440s
sys 0m5.920s

Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Gao Pan <b54642@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[wsa: sorted includes]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-03 19:08:09 +01:00
Gao Pan a5f650182b i2c: imx: init bus recovery info before adding i2c adapter
During driver probe, i2c_imx_init_recovery_info() must come before
i2c_add_numbered_adapter(), because the get/set_scl() functions
are assigned in i2c_register_adapter() under the conditon that bus
recover_info are initialized. Otherwise, get/set_scl() function
pointers never get assigned.

In such case, when i2c_generic_gpio_recovery() is used for bus recovery,
there will be kernel crash because bri->set_scl is NULL.

The solution to this bug is moving i2c_imx_init_recovery_info() before
i2c_register_adapter().

Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2016-01-03 19:06:50 +01:00
Wolfram Sang 7ee24eb508 i2c: rcar: disable PM in multi-master mode
In multi master mode, the IP core needs to be always active for
arbitration reasons. Get the config from DT and set up PM depending on
the config.

Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-02 22:11:48 +01:00
Wolfram Sang 42c0783b89 i2c: rcar: remove macros dealing with flags
These macros don't really hide complexity, but C idioms. Removing them
makes the code easier to read IMO and make a planned extension easier.

Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-02 22:11:21 +01:00
Sifan Naeem c20821a7f0 i2c: img-scb: support repeated starts on IP v3.3
In version 3.3 of the IP when transaction halt is set, an interrupt
will be generated after each byte of a transfer instead of after
every transfer but before the stop bit.
Due to this behaviour we have to be careful that every time we
release the transaction halt we have to re-enable it straight away
so that we only process a single byte, not doing so will result in
all remaining bytes been processed and a stop bit being issued,
which will prevent us having a repeated start.

This change will have no effect on earlier versions of the IP.

Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-02 22:05:21 +01:00
Sifan Naeem c7b0a7c107 i2c: img-scb: add handle for Master halt interrupt
Master halt is issued after each byte of a transaction is processed in
IP version 3.3.
Master halt will stall the bus by holding the SCK line low until the
halt bit in the scb_general_control is cleared.

After the last byte of a transfer is processed we can use the Master
Halt interrupt to facilitate a repeated start transfer without
issuing a stop bit.

Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-02 22:04:55 +01:00
Sifan Naeem dd29207e6c i2c: img-scb: add handle for stop detected interrupt
Stop Detected interrupt is triggered when a Stop bit is detected on
the bus, which indicates the end of the current transfer.

When the end of a transfer is indicated by the Stop Detected interrupt,
drain the FIFO and signal completion for the transaction.

Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-02 22:04:30 +01:00
Sifan Naeem a8c5a8d8c9 i2c: img-scb: remove fifo EMPTYING interrupts handle
Now that we are using the transaction halt interrupt to safely control
repeated start transfers, we no longer need to handle the fifo
emptying interrupts.

Handling this interrupt along with Transaction Halt interrupt can
cause erratic behaviour.

Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-02 22:04:05 +01:00
Sifan Naeem c55ebe0e72 i2c: img-scb: support I2C_M_IGNORE_NAK
This commit adds support for the I2C_M_IGNORE_NAK protocol
modification.

Such behaviour can only be implemented in atomic mode. So, if a
transaction contains a message with such flag the drivers
switches to atomic mode. The implementation consists simply in
treating NAKs as ACKs.

Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-01-02 22:03:39 +01:00
Wolfram Sang b4cd08aa1f i2c: rcar: disable runtime PM correctly in slave mode
When we also are I2C slave, we need to disable runtime PM because the
address detection mechanism needs to be active all the time. However, we
can reenable runtime PM once the slave instance was unregistered. So,
use pm_runtime_get_sync/put to achieve this, since it has proper
refcounting. pm_runtime_allow/forbid is like a global knob controllable
from userspace which is unsuitable here.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2015-12-19 12:00:37 +01:00
Wolfram Sang 54177ccfbe i2c: make i2c_parse_fw_timings() always visible
This function used to be DT only, so it lived inside a CONFIG_OF block.
Now it uses device attributes and must be moved outside of it. No
further code changes, only one whitespace improvement.

Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-17 20:36:39 +01:00
Wolfram Sang b7d518e6f4 i2c: emev: select I2C slave support
Until we have proper support to make I2C slave support fully optional,
select it to prevent build errors on randconfigs.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-17 20:34:36 +01:00
Måns Rullgård 5398b7ef6c i2c: xlr: add interrupt support for Sigma Designs chips
The Sigma Designs variant of this controller has the ability to generate
interrupts.  This is controlled using two additional registers, oddly
enough overlapping with the defined but unused HDSTATIM.

This patch adds support for using this feature instead of busy-looping
if an IRQ is specified.

Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-16 11:42:58 +01:00
Måns Rullgård a45af72a60 i2c: xlr: fix extra read/write at end of rx transfer
The BYTECNT register holds the transfer size minus one.  Setting it to
the correct value removes the need for a dummy read/write at the end of
each transfer.  As zero-length transfers are not supported, do not
advertise I2C_FUNC_SMBUS_QUICK.

In other words, this patch makes the driver transfer the number of bytes
requested unless this is zero, which is not supported by the hardware
and is thus refused.

Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-16 11:42:30 +01:00
Måns Rullgård 75d31c2372 i2c: xlr: add support for Sigma Designs controller variant
Sigma Designs chips use a variant of this controller with the following
differences:

- The BUSY bit in the STATUS register is inverted
- Bit 8 of the CONFIG register must be set
- The controller can generate interrupts

This patch adds support for the first two of these.  It also calculates
and sets the correct clock divisor if a clk is provided.  The bus
frequency is optionally speficied in the device tree node.

Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-15 13:13:00 +01:00
Masahiro Yamada 51549c087f i2c: uniphier_f: error out if bus speed is zero
There is code to divide by "bus_speed" some lines below.
To eliminate the possibility of division by zero, bail out if
"clock-frequency" is specified as zero.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-14 10:59:46 +01:00
Masahiro Yamada ac9b91f39d i2c: uniphier_f: error out if clock rate is zero
This input clock is used to generate the sampling clock for I2C bus.
If the clock rate is zero, there is something wrong with the clock
driver.  Bail out with the appropriate error message in such a case.
It would make it easier to find the root cause of failure.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-14 10:59:26 +01:00
Masahiro Yamada 2d5d23b96a i2c: uniphier: error out if bus speed is zero
There is code to divide by "bus_speed" some lines below.
To eliminate the possibility of division by zero, bail out if
"clock-frequency" is specified as zero.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-14 10:59:05 +01:00
Masahiro Yamada 1ff49b34bf i2c: uniphier: error out if clock rate is zero
This input clock is used to generate the sampling clock for I2C bus.
If the clock rate is zero, there is something wrong with the clock
driver.  Bail out with the appropriate error message in such a case.
It would make it easier to find the root cause of failure.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-14 10:58:44 +01:00
Wolfram Sang ca68eade66 i2c: rcar: honor additional i2c timings from DT
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-14 10:51:10 +01:00
Wolfram Sang c7881871de i2c: rcar: switch to i2c generic dt parsing
Switch to the new generic functions. Plain convert, no functionality
added yet.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-14 10:51:09 +01:00
Wolfram Sang f9c9d31bdd i2c: rcar: refactor probe function a little
The probe function is a little bit messy, something here, something
there. Rework it so that there is some order: first init the private
structure, then the adapter, then do HW init. This also allows us to
remove the device argument of the clock calculation function, because it
now can be deduced from the private structure. Also, shorten some lines
where possible. This is a preparation for further refactoring.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-14 10:51:08 +01:00
Wolfram Sang e1dba01ca6 i2c: add generic routine to parse DT for timing information
Inspired from the i2c-rk3x driver (thanks guys!) but refactored and
extended. See built-in docs for further information.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-14 10:51:07 +01:00
Jarkko Nikula e79e72c5a2 i2c: designware: Keep pm_runtime_enable/_disable calls in sync
On an hardware shared I2C bus (certain Intel Baytrail SoC platforms) the
runtime PM disable depth keeps increasing over repeated modprobe/rmmod
cycle because pm_runtime_disable() is called without checking should it
be disabled already because of bus sharing.

This hasn't made any other harm than dev->power.disable_depth keeps
increasing but keep it sync by calling pm_runtime_disable() only when
runtime PM is not disabled.

Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-12 18:04:57 +01:00
Xiangliang Yu 2d244c8148 i2c: designware: fix IO timeout issue for AMD controller
Because of some hardware limitation, AMD I2C controller can't
trigger pending interrupt if interrupt status has been changed
after clearing interrupt status bits. Then, I2C will lost
interrupt and IO timeout.

According to hardware design, this patch implements a workaround
to disable i2c controller interrupt and re-enable i2c interrupt
before exiting ISR.

To reduce the performance impacts on other vendors, use unlikely
function to check flag in ISR.

Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2015-12-12 18:00:16 +01:00
Gao Pan 5212f9ae51 i2c: imx: init bus recovery info before adding i2c adapter
During driver probe, i2c_imx_init_recovery_info() must come before
i2c_add_numbered_adapter(), because the get/set_scl() functions
are assigned in i2c_register_adapter() under the conditon that bus
recover_info are initialized. Otherwise, get/set_scl() function
pointers never get assigned.

In such case, when i2c_generic_gpio_recovery() is used for bus recovery,
there will be kernel crash because bri->set_scl is NULL.

The solution to this bug is moving i2c_imx_init_recovery_info() before
i2c_register_adapter().

Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2015-12-09 11:15:41 +01:00
Andy Shevchenko 4077a387b7 x86/platform/iosf_mbi: Remove duplicate definitions
The read and write opcodes are global for all units on SoC and even across
Intel SoCs. Remove duplication of corresponding constants. At the same time
convert all current users.

No functional change.

Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Boon Leong Ong <boon.leong.ong@intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-12-09 01:18:34 +01:00
Mika Westerberg 4c5301abbf i2c: designware: Convert to use unified device property API
With ACPI _DSD (introduced in ACPI v5.1) it is now possible to pass device
configuration information from ACPI in addition to DT. In order to support
this, convert the driver to use the unified device property accessors
instead of DT specific.

Change to ordering a bit so that we first try platform data and if that's
not available look from device properties. ACPI *CNT methods are then used
as last resort to override everything else.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-12-07 02:29:24 +01:00
Niklas Söderlund c31d0a0002 i2c: emev2: add slave support
Add I2C slave provider using the generic slave interface.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-05 19:55:36 +01:00
Paul Burton 7a852b02d4 i2c: eg20t: allow build on MIPS platforms
Allow the eg20t I2C driver to be built for MIPS platforms, in
preparation for use on the MIPS Boston board.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-03 22:11:47 +01:00
Paul Burton a613d9d485 i2c: eg20t: set i2c_adapter->dev.of_node
Set the I2C adapter devices of_node to that of the PCI device, such that
I2C clients may be instantiated via device tree.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-03 22:11:46 +01:00
Ludovic Desroches cc018e3612 i2c: at91: add support for the HOLD field
The hold field allows to configure the data hold time which can be set
with the help of the generic binding 'i2c-sda-hold-time-ns'. This
feature has been introduced with SAMA5D4 SoC family.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-12-03 21:42:37 +01:00