Commit Graph

329 Commits

Author SHA1 Message Date
Lv Zheng c3a696b6e8 ACPI / EC: Use busy polling mode when GPE is not enabled
When GPE is not enabled, it is not efficient to use the wait polling mode
as it introduces an unexpected scheduler delay.
So before the GPE handler is installed, this patch uses busy polling mode
for all EC(s) and the logic can be applied to non boot EC(s) during the
suspend/resume process.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=191561
Tested-by: Jakobus Schurz <jakobus.schurz@gmail.com>
Tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-01-30 12:12:52 +01:00
Lv Zheng 4c237371f2 ACPI / EC: Remove old CLEAR_ON_RESUME quirk
IRQ polling logic has been implemented to drain the post-boot/resume
EC events:

 1. Triggered by the following code, invoked from acpi_ec_enable_event():

	if (!test_bit(EC_FLAGS_QUERY_PENDING, &ec->flags))
		advance_transaction(ec);

 2. Drained by the following code, invoked after acpi_ec_complete_query():

	if (status & ACPI_EC_FLAG_SCI)
		acpi_ec_submit_query(ec);

This facility is safer than the old CLEAR_ON_RESUME quirk as the
CLEAR_ON_RESUME quirk sends EC query commands unconditionally. The
behavior is apparently not suitable for firmware that requires
QUERY_HANDSHAKE quirk. Though the QUERY_HANDSHAKE quirk isn't used
now because of the improvement done in the EC transaction state
machine (ec_event_clearing=QUERY), it is the proof that we cannot
send EC query command unconditionally.

So it's time to delete the out-dated CLEAR_ON_RESUME quirk to let the
users to try the newer approach.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=191211
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-01-30 12:12:03 +01:00
Eric Biggers eab05ec380 ACPI / EC: Fix unused function warning when CONFIG_PM_SLEEP=n
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-10-10 02:22:20 +02:00
Lv Zheng 97cb159fd9 ACPI / EC: Fix issues related to boot_ec
There are issues related to the boot_ec:
1. If acpi_ec_remove() is invoked, boot_ec will also be freed, this is not
   expected as the boot_ec could be enumerated via ECDT.
2. Address space handler installation/unstallation lead to unexpected _REG
   evaluations.
This patch adds acpi_is_boot_ec() check to be used to fix the above issues.
However, since acpi_ec_remove() actually won't be invoked, this patch
doesn't handle the reference counting of "struct acpi_ec", it only ensures
the correctness of the boot_ec destruction during the boot.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=153511
Reported-and-tested-by: Jonh Henderson <jw.hendy@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-09-10 02:33:50 +02:00
Lv Zheng 2a5708409e ACPI / EC: Fix a gap that ECDT EC cannot handle EC events
It is possible to register _Qxx from namespace and use the ECDT EC to
perform event handling. The reported bug reveals that Windows is using ECDT
in this way in case the namespace EC is not present. This patch facilitates
Linux to support ECDT in this way.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=115021
Reported-and-tested-by: Luya Tshimbalanga <luya@fedoraproject.org>
Tested-by: Jonh Henderson <jw.hendy@gmail.com>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-09-10 02:33:50 +02:00
Lv Zheng 46922d2a3a ACPI / EC: Fix a memory leakage issue in acpi_ec_add()
When the handler installation failed, there was no code to free the
allocated EC device. This patch fixes this memory leakage issue.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=115021
Reported-and-tested-by: Luya Tshimbalanga <luya@fedoraproject.org>
Tested-by: Jonh Henderson <jw.hendy@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-09-10 02:33:49 +02:00
Lv Zheng 72c77b7ea9 ACPI / EC: Cleanup first_ec/boot_ec code
In order to support full ECDT (driving the ECDT EC after probing the
namespace EC), we need to change our EC device alloc/free algorithm, ensure
not to free old boot EC before qualifying new boot EC.
This patch achieves this by cleaning up first_ec/boot_ec logic:
1. first_ec: used to perform transactions, so it is assigned in new
   acpi_ec_setup() function.
2. boot_ec: used to track early EC device, so it is assigned in new
   acpi_config_boot_ec() function which explictly tells the driver to save
   the EC device as early EC device.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=115021
Reported-and-tested-by: Luya Tshimbalanga <luya@fedoraproject.org>
Tested-by: Jonh Henderson <jw.hendy@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-09-10 02:33:49 +02:00
Lv Zheng d30283057e ACPI / EC: Enable event freeze mode to improve event handling for suspend process
This patch enables the event freeze mode, flushing the EC event handling in
.suspend() callback. This feature is experimental, if it is bisected out to
be the cause of the real issues, please report the issues to the kernel
bugzilla for further root causing and improvement.

This mode eliminates useless _Qxx handling during the power saving
operations, thus can help to tune the power saving operations faster. Tests
show that this mode can efficiently block flooding _Qxx during the suspend
process and tune the speed of the suspend faster.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Tested-by: Todd E Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-08-31 00:32:11 +02:00
Lv Zheng 39a2a2aa3e ACPI / EC: Add PM operations to improve event handling for suspend process
In the original EC driver, though the event handling is not explicitly
stopped, the EC driver is actually not able to handle events during the
noirq stage as the EC driver is not prepared to handle the EC events in the
polling mode. So if there is no advance_transaction() triggered, the EC
driver couldn't notice the EC events.
However, do we actually need to handle EC events during suspend/resume
stage? EC events are mostly useless for the suspend/resume period (key
strokes and battery/thermal updates, etc.,), and the useful ones (lid
close, power/sleep button press) should have already been delivered to the
OSPM to trigger the power saving operations.
Thus this patch implements acpi_ec_disable_event() to be a reverse call of
acpi_ec_enable_event(), with which, the EC driver is able to stop handling
the EC events in a position before entering the noirq stage.

Since there are actually 2 choices for us:
1. implement event handling in polling mode;
2. stop event handling before entering noirq stage.
And this patch only implements the second choice using .suspend() callback.
Thus this is experimental (first choice is better? or different hook
position is better?). This patch finally keeps the old behavior by default
and prepares a boot parameter to enable this feature.

The differences of the event handling availability between the old behavior
(this patch is not applied) and the new behavior (this patch is applied)
are as follows:
                        !FreezeEvents   FreezeEvents
before suspend          Y               Y
suspend before EC       Y               Y
suspend after EC        Y               N
suspend_late            Y               N
suspend_noirq           Y (actually N)  N
resume_noirq            Y (actually N)  N
resume_late             Y (actually N)  N
resume before EC        Y (actually N)  N
resume after EC         Y               Y
after resume            Y               Y
Where "actually N" means if there is no EC transactions, the EC driver
is actually not able to notice the pending events.

We can see that FreezeEvents is the only approach now can actually flush
the EC event handling with both query commands and _Qxx evaluations
flushed, other modes can only flush the EC event handling with only query
commands flushed, _Qxx evaluations occurred after stopping the EC driver
may end up failure due to the failure of the EC transaction carried out in
the _Qxx control methods.

We also can see that this feature should be able to trigger some platform
notifications later than resuming other drivers.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Tested-by: Todd E Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-08-31 00:32:11 +02:00
Lv Zheng c2b46d679b ACPI / EC: Add PM operations to improve event handling for resume process
This patch makes 2 changes:

1. Restore old behavior
Originally, EC driver stops handling both events and transactions in
acpi_ec_block_transactions(), and restarts to handle transactions in
acpi_ec_unblock_transactions_early(), restarts to handle both events and
transactions in acpi_ec_unblock_transactions().
While currently, EC driver still stops handling both events and
transactions in acpi_ec_block_transactions(), but restarts to handle both
events and transactions in acpi_ec_unblock_transactions_early().
This patch tries to restore the old behavior by dropping
__acpi_ec_enable_event() from acpi_unblock_transactions_early().

2. Improve old behavior
However this still cannot fix the real issue as both of the
acpi_ec_unblock_xxx() functions are invoked in the noirq stage. Since the
EC driver actually doesn't implement the event handling in the polling
mode, re-enabling the event handling too early in the noirq stage could
result in the problem that if there is no triggering source causing
advance_transaction() to be invoked, pending SCI_EVT cannot be detected by
the EC driver and _Qxx cannot be triggered.
It actually makes sense to restart the event handling in any point during
resuming after the noirq stage. Just like the boot stage where the event
handling is enabled in .add(), this patch further moves
acpi_ec_enable_event() to .resume(). After doing that, the following 2
functions can be combined:
acpi_ec_unblock_transactions_early()/acpi_ec_unblock_transactions().

The differences of the event handling availability between the old behavior
(this patch isn't applied) and the new behavior (this patch is applied) are
as follows:
                        !Applied        Applied
before suspend          Y               Y
suspend before EC       Y               Y
suspend after EC        Y               Y
suspend_late            Y               Y
suspend_noirq           Y (actually N)  Y (actually N)
resume_noirq            Y (actually N)  Y (actually N)
resume_late             Y (actually N)  Y (actually N)
resume before EC        Y (actually N)  Y (actually N)
resume after EC         Y (actually N)  Y
after resume            Y (actually N)  Y
Where "actually N" means if there is no triggering source, the EC driver
is actually not able to notice the pending SCI_EVT occurred in the noirq
stage. So we can clearly see that this patch has improved the situation.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Tested-by: Todd E Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-08-31 00:32:10 +02:00
Lv Zheng e923e8e79e ACPI / EC: Fix an issue that SCI_EVT cannot be detected after event is enabled
After enabling the EC event handling, Linux is still in the noirq stage, if
there is no triggering source (EC transaction, GPE STS status),
advance_transaction() will not be invoked and SCI_EVT cannot be detected.
This patch adds one more triggering source after enabling the EC event
handling to poll the pending SCI_EVT.

Known issues:
1. Still no SCI_EVT triggering source
   There could still be no SCI_EVT triggering source after handling the
   first SCI_EVT (polled by this patch if any). Because after handling the
   first SCI_EVT, Linux could still be in noirq stage and there could still
   be no further triggering source in this stage. Then the second SCI_EVT
   indicated during this stage still cannot be detected by the EC driver.
   With this improvement applied, it is then possible to move
   acpi_ec_enable_event() out of the noirq stage to fix this issue (if the
   first SCI_EVT is handled out of the noirq stage, the follow-up SCI_EVTs
   should be able to trigger IRQs).

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Tested-by: Todd E Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-08-31 00:32:10 +02:00
Lv Zheng 750f628be6 ACPI / EC: Add EC_FLAGS_QUERY_ENABLED to reveal a hidden logic
There is a hidden logic in the EC driver:
1. During boot, EC_FLAGS_QUERY_PENDING is responsible for blocking event
   handling;
2. During suspend, EC_FLAGS_STARTED is responsible for blocking event
   handling.
This patch uses a new EC_FLAGS_QUERY_ENABLED flag to make this hidden
logic explicit and have code cleaned up. No functional change.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Tested-by: Todd E Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-08-31 00:32:10 +02:00
Lv Zheng df45db6177 ACPI / EC: Add PM operations for suspend/resume noirq stage
It is reported that on some platforms, resume speed is not fast. The cause
is: in noirq stage, EC driver is working in polling mode, and each state
machine advancement requires a context switch.

The context switch is not necessary to the EC driver's polling mode. This
patch implements PM hooks to automatically switch the driver to/from the
busy polling mode to eliminate the overhead caused by the context switch.

This finally contributes to the tuning result: acpi_pm_finish() execution
time is improved from 192ms to 6ms.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reported-and-tested-by: Todd E Brandt <todd.e.brandt@linux.intel.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-08-17 02:37:02 +02:00
Rafael J. Wysocki 4dc14b343d Merge branches 'acpi-ec' and 'acpi-button'
* acpi-ec:
  ACPI / EC: Work around method reentrancy limit in ACPICA for _Qxx

* acpi-button:
  ACPI / button: remove pointer to old lid_sysfs on unbind
2016-08-05 16:04:49 +02:00
Lv Zheng e1191bd4f6 ACPI / EC: Work around method reentrancy limit in ACPICA for _Qxx
A regression is caused by the following commit:

  Commit: 02b771b64b
  Subject: ACPI / EC: Fix an issue caused by the serialized _Qxx evaluations

In this commit, using system workqueue causes that the maximum parallel
executions of _Qxx can exceed 255. This violates the method reentrancy
limit in ACPICA and generates the following error log:

  ACPI Error: Method reached maximum reentrancy limit (255) (20150818/dsmethod-341)

This patch creates a seperate workqueue and limits the number of parallel
_Qxx evaluations down to a configurable value (can be tuned against number
of online CPUs).

Since EC events are handled after driver probe, we can create the workqueue
in acpi_ec_init().

Fixes: 02b771b64b (ACPI / EC: Fix an issue caused by the serialized _Qxx evaluations)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=135691
Cc: 4.3+ <stable@vger.kernel.org> # 4.3+
Reported-and-tested-by: Helen Buus <ubuntu@hbuus.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-08-04 02:07:53 +02:00
Rafael J. Wysocki f6bc0a168e Merge branches 'acpi-ec', 'acpi-video', 'acpi-button' and 'acpi-thermal'
* acpi-ec:
  ACPI / EC: Remove wrong ECDT correction quirks
  ACPI / EC: Cleanup boot EC code using acpi_ec_alloc()

* acpi-video:
  ACPI / video: Dummy acpi_video_register should return error code
  ACPI / video: skip evaluating _DOD when it does not exist
  ACPI / video: Thinkpad X201 Tablet needs video_detect_force_video

* acpi-button:
  ACPI / button: Add quirks for initial lid state notification
  ACPI / button: Refactor functions to eliminate redundant code
  ACPI / button: Remove initial lid state notification

* acpi-thermal:
  ACPI / thermal: Remove create_workqueue()
2016-07-25 13:42:00 +02:00
Lv Zheng fa5b4a509d ACPI / EC: Fix code ordering issue in ec_remove_handlers()
There is an order issue in ec_remove_handlers() that acpi_ec_stop()
is called before removing the operation region handler. That is
incorrect, because the operation region handler removal triggers
_REG(DISCONNECT) which may result in new EC transactions to carry
out.

That existing issue has been triggered by the following commit:

    Commit: dcf15cbded
    Subject: ACPI / EC: Fix a boot EC regresion by restoring boot EC

which changed the driver to call ec_remove_handlers() after invoking
_REG(CONNECT), so the issue has become visible.

Fixes: dcf15cbded (ACPI / EC: Fix a boot EC regresion by restoring boot EC)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=102421
Reported-and-tested-by: Wolfram Sang <wsa@the-dreams.de>
Reported-by: Nicholas <nkudriavtsev@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-07-08 21:44:12 +02:00
Lv Zheng bc539567ab ACPI / EC: Remove wrong ECDT correction quirks
Our Windows probe result shows that EC._REG is evaluated after evaluating
all _INI/_STA control methods.

With boot EC always switched in acpi_ec_dsdt_probe(), we can see that as
long as there is no EC opregion accesses in the MLC (module level code, AML
code out of any control methods) and in _INI/_STA, there is no need to make
sure that ECDT must be correct.

Bugs of 9399/12461 were reported against an order issue that BAT0/1._STA
evaluations contain EC accesses while the ECDT setting is wrong.

>From the acpidump output posted on bug 9399, we can see that it is actually
a different issue. In this table, if EC._REG is not executed, EC accesses
will be done in a platform specific manner. As we've already ensured not to
execute EC._REG during the eary stage, we can remove the quirks for bug
9399.

From the acpidump output posted on bug 12461, we can see that it still
needs the quirk. In this table, EC._REG flags a named object whose default
value is One, thus BAT1._STA surely should invoke EC accesses whatever we
invoke EC._REG or not. We have to keep the quirk for it before we can root
cause the issue.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-07-04 15:30:06 +02:00
Lv Zheng fd6231e785 ACPI / EC: Cleanup boot EC code using acpi_ec_alloc()
Failure handling of the boot EC code is not tidy. This patch cleans
them up with acpi_ec_alloc().

This patch also changes acpi_ec_dsdt_probe(), always switches the
boot EC from the ECDT one to the DSDT one in this function.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-07-04 15:30:06 +02:00
Lv Zheng dcf15cbded ACPI / EC: Fix a boot EC regresion by restoring boot EC support for the DSDT EC
According to the Windows probing result, during the table loading, the EC
device described in the ECDT should be used. And the ECDT EC is also
effective during the period the namespace objects are initialized (we can
see a separate process executing _STA/_INI on Windows before executing
other device specific control methods, for example, EC._REG). During the
device enumration, the EC device described in the DSDT should be used. But
there are differences between Linux and Windows around the device probing
order. Thus in Linux, we should enable the DSDT EC as early as possible
before enumerating devices in order not to trigger issues related to the
device enumeration order differences.

This patch thus converts acpi_boot_ec_enable() into acpi_ec_dsdt_probe() to
fix the gap. This also fixes a user reported regression triggered after we
switched the "table loading"/"ECDT support" to be ACPI spec 2.0 compliant.

Fixes: 59f0aa9480 (ACPI 2.0 / ECDT: Remove early namespace reference from EC)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=119261
Reported-and-tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-06-07 02:29:53 +02:00
Lv Zheng 59f0aa9480 ACPI 2.0 / ECDT: Remove early namespace reference from EC
All operation region accesses are allowed by AML interpreter when AML is
executed, so actually BIOSen are responsible to avoid the operation region
accesses in AML before OSPM has prepared an operation region driver. This
is done via _REG control method. So AML code normally sets a global named
object REGC to 1 when _REG(3, 1) is evaluated.

Then what is ECDT? Quoting from ACPI spec 6.0, 5.2.15 Embedded Controller
Boot Resources Table (ECDT):
 "The presence of this table allows OSPM to provide Embedded Controller
  operation region space access before the namespace has been evaluated."
Spec also suggests a compatible mean to indicate the early EC access
availability:
 Device (EC)
 {
     Name (REGC, Ones)
     Method (_REG, 2)
     {
         If (LEqual (Arg0, 3))
         {
             Store (Arg1, REGC)
         }
     }
     Method (ECAV)
     {
         If (LEqual (REGC, Ones))
         {
             If (LGreaterEqual (_REV, 2))
             {
                 Return (One)
             }
             Else
             {
                 Return (Zero)
             }
         }
         Else
         {
             Return (REGC)
         }
     }
 }
In this way, it allows EC accesses to happen before EC._REG(3, 1) is
invoked.

But ECAV is not the only way practical BIOSen using to indicate the early
EC access availibility, the known variations include:
1. Setting REGC to One in \_SB._INI when _REV >= 2. Since \_SB._INI is the
   first control method evaluated by OSPM during the enumeration, this
   allows EC accesses to happen for the entire enumeration process before
   the namespace EC is enumerated.
2. Initialize REGC to One by default, this even allows EC accesses to
   happen during the table loading.

Linux is now broken around ECDT support during the long term bug fixing
work because it has merged many wrong ECDT bug fixes (see details below).
Linux currently uses namespace EC's settings instead of ECDT settings when
ECDT is detected. This apparently will result in namespace walk and
_CRS/_GPE/_REG evaluations. Such stuffs could only happen after namespace
is ready, while ECDT is purposely to be used before namespace is ready.

The wrong bug fixing story is:
1. Link 1:
   At Linux ACPI early stages, "no _Lxx/_Exx/_Qxx evaluation can happen
   before the namespace is ready" are not ensured by ACPICA core and Linux.
   This is currently ensured by deferred enabling of GPE and defered
   registering of EC query methods (acpi_ec_register_query_methods).
2. Link 2:
   Reporters reported buggy ECDTs, expecting quirks for the platform.
   Originally, the quirk is simple, only doing things with ECDT.
   Bug 9399 and 12461 are platforms (Asus L4R, Asus M6R, MSI MS-171F)
   reported to have wrong ECDT IO port addresses, the port addresses are
   reversed.
   Bug 11880 is a platform (Asus X50GL) reported to have 0 valued port
   addresses, we can see that all EC accesses are protected by ECAV on
   this platform, so actually no early EC accesses is required by this
   platform.
3. Link 3:
   But when the bug fixing developer was requested to provide a handy and
   non-quirk bug fix, he tried to use correct EC settings from namespace
   and broke the spec purpose. We can even see that the developer was
   suffered from many regrssions. One interesting one is 14086, where the
   actual root cause obviously should be: _REG is evaluated too early. But
   unfortunately, the bug is fixed in a totally wrong way.

So everything goes wrong from these commits:
   Commit: c6cb0e8784
   Subject: ACPI: EC: Don't trust ECDT tables from ASUS
   Commit: a5032bfdd9
   Subject: ACPI: EC: Always parse EC device

This patch reverts Linux behavior to simple ECDT quirk support in order to
stop early _CRS/_GPE/_REG evaluations.
For Bug 9399, 12461, since it is reported that the platforms require early
EC accesses, this patch restores the simple ECDT quirks for them.
For Bug 11880, since it is not reported that the platform requires early EC
accesses and its ACPI tables contain correct ECAV, we choose an ECDT
enumeration failure for this platform.

Link 1: https://bugzilla.kernel.org/show_bug.cgi?id=9916
        http://bugzilla.kernel.org/show_bug.cgi?id=10100
        https://lkml.org/lkml/2008/2/25/282
Link 2: https://bugzilla.kernel.org/show_bug.cgi?id=9399
        https://bugzilla.kernel.org/show_bug.cgi?id=12461
        https://bugzilla.kernel.org/show_bug.cgi?id=11880
Link 3: https://bugzilla.kernel.org/show_bug.cgi?id=11884
        https://bugzilla.kernel.org/show_bug.cgi?id=14081
        https://bugzilla.kernel.org/show_bug.cgi?id=14086
        https://bugzilla.kernel.org/show_bug.cgi?id=14446
Link 4: https://bugzilla.kernel.org/show_bug.cgi?id=112911
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Tested-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-04-09 03:06:44 +02:00
Lv Zheng 0e1affe41b ACPI 2.0 / ECDT: Split EC_FLAGS_HANDLERS_INSTALLED
This patch splits EC_FLAGS_HANDLERS_INSTALLED so that address space handler
can be installed when it is not possible to install GPE handler during
early stage.
This patch also tunes address space handler installation, making it
happening earlier than GPE handler installation for the same purpose.

Since acpi_ec_start()/acpi_ec_stop() will be entered multiple times after
applying this change, it is also required to protect acpi_enable_gpe()/
acpi_disable_gpe() invocations.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=112911
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Tested-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-04-09 03:06:43 +02:00
Markus Elfring 4981c2b7ab ACPI-EC: Drop unnecessary check made before calling acpi_ec_delete_query()
The acpi_ec_delete_query() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-11-16 23:29:44 +01:00
Lv Zheng 6119754707 ACPI / EC: Fix a race issue in acpi_ec_guard_event()
In acpi_ec_guard_event(), EC transaction state machine variables should be
checked with the EC spinlock locked.
The bug doesn't trigger any real issue now because this bug can only occur
when the ec_event_clearing=event mode is applied while there is no user
currently using this mode.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-09-26 01:46:25 +02:00
Lv Zheng 0700c047f6 ACPI / EC: Fix query handler related issues
1. acpi_ec_remove_query_handlers()
This patch refines the query handler removal logic implemented in
acpi_ec_remove_query_handler(), making it to invoke new
acpi_ec_remove_query_handlers() API, and ensuring all other removal code
paths to invoke the new API to honor the reference count of the query
handlers.

2. acpi_ec_get_query_handler_by_value()
This patch also refines the query handler search logic originally
implemented in acpi_ec_query(), collecting it into
acpi_ec_get_query_handler_by_value(). And since schedule_work() can ensure
the serilization of acpi_ec_event_handler(), we needn't put the
mutex_lock() around schedule_work().

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-09-26 01:46:24 +02:00
Lv Zheng 15b94fa32a ACPI / EC: Fix a memory leak issue in acpi_ec_query()
When query handler is not found, "result" is actually stil 0, and
"struct acpi_ec_query" is not NULL, so the deletion code of
"struct acpi_ec_query" at the end of the function cannot be invoked.
As a consequence, memory leak can be observed.

The issue is introduced by this commit:
  Commit: 02b771b64b
  Subject: ACPI / EC: Fix an issue caused by the serialized _Qxx

This patch fixes such memory leakage.

Fixes: 02b771b64b (ACPI / EC: Fix an issue caused by the serialized _Qxx evaluations)
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-09-26 01:44:59 +02:00
Rafael J. Wysocki 5d2a1a927d Merge branches 'acpi-pci', 'acpi-soc', 'acpi-ec' and 'acpi-osl'
* acpi-pci:
  ACPI, PCI: Penalize legacy IRQ used by ACPI SCI

* acpi-soc:
  ACPI / LPSS: Ignore 10ms delay for Braswell

* acpi-ec:
  ACPI / EC: Fix an issue caused by the serialized _Qxx evaluations

* acpi-osl:
  ACPI / osl: replace custom implementation of readq / writeq
2015-09-01 03:41:19 +02:00
Lv Zheng 02b771b64b ACPI / EC: Fix an issue caused by the serialized _Qxx evaluations
It is proven that Windows evaluates _Qxx handlers in a parallel way. This
patch follows this fact, splits _Qxx evaluations from the NOTIFY queue to
form a separate queue, so that _Qxx evaluations can be queued up on
different CPUs rather than being queued up on a CPU0 bound queue.
Event handling related callbacks are also renamed and sorted in this patch.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=94411
Reported-and-tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-08-25 03:19:32 +02:00
Jarkko Nikula 4c62dbbce9 ACPI: Remove FSF mailing addresses
There is no need to carry potentially outdated Free Software Foundation
mailing address in file headers since the COPYING file includes it.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-07-08 02:27:32 +02:00
Lv Zheng 66db383439 ACPI / EC: Fix a code coverity issue when QR_EC transactions are failed.
When the QR_EC transaction fails, the EC_FLAGS_QUERY_PENDING flag prevents
the event handling work queue from being scheduled again.

Though there shouldn't be failed QR_EC transactions, and this gap was
efficiently used for catching and learning the SCI_EVT clearing timing
compliance issues, we need to fix this as we are not fully compatible
with all platforms/Windows to handle SCI_EVT clearing timing correctly.
Fixing this gives the EC driver the chances to recover from a state machine
failure.

So this patch fixes this issue. When nr_pending_queries drops to 0, it
clears EC_FLAGS_QUERY_PENDING at the proper position for different modes in
order to ensure that the SCI_EVT handling can proceed.

In order to be clearer for future ec_event_clearing modes, all checks in
this patch are written in the inclusive style, not the exclusive style.

Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-06-15 14:35:59 +02:00
Lv Zheng 3cb02aeb28 ACPI / EC: Fix EC_FLAGS_QUERY_HANDSHAKE platforms using new event clearing timing.
It is reported that on several platforms, EC firmware will not respond
non-expected QR_EC (see EC_FLAGS_QUERY_HANDSHAKE, only write QR_EC when
SCI_EVT is set).

Unfortunately, ACPI specification doesn't define when the SCI_EVT should be
cleared by the firmware, thus the original implementation queued up second
QR_EC right after writing QR_EC command and before reading the returned
event value as at that time the SCI_EVT is ensured not cleared. This
behavior is also based on the assumption that the firmware should be able
to return 0x00 to indicate "no outstanding event". This behavior did fix
issues on Samsung platforms where the spurious query value of 0x00 is
supported and didn't break platforms in my test queue.

But recently, specific Acer, Asus, Lenovo platforms keep on blaming this
change.

This patch changes the behavior to re-check the SCI_EVT a bit later and
removes EC_FLAGS_QUERY_HANDSHAKE quirks, hoping this is the Windows
compliant EC driver behavior.

In order to be robust to the possible regressions, instead of removing the
quirk directly, this patch keeps the quirk code, removes the quirk users
and keeps old behavior for Samsung platforms.

Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Link: https://bugzilla.kernel.org/show_bug.cgi?id=94411
Link: https://bugzilla.kernel.org/show_bug.cgi?id=97381
Link: https://bugzilla.kernel.org/show_bug.cgi?id=98111
Reported-and-tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reported-and-tested-by: Tigran Gabrielyan <tigrangab@gmail.com>
Reported-and-tested-by: Adrien D <ghbdtn@openmailbox.org>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-06-15 14:35:59 +02:00
Lv Zheng 1d68d2612c ACPI / EC: Add event clearing variation support.
We've been suffering from the uncertainty of the SCI_EVT clearing timing.
This patch implements 3 of 4 possible modes to handle SCI_EVT clearing
variations. The old behavior is kept in this patch.

Status: QR_EC is re-checked as early as possible after checking previous
        SCI_EVT. This always leads to 2 QR_EC transactions per SCI_EVT
        indication and the target may implement event queue which returns
        0x00 indicating "no outstanding event".
        This is proven to be a conflict against Windows behavior, but is
        still kept in this patch to make the EC driver robust to the
        possible regressions that may occur on Samsung platforms.
Query: QR_EC is re-checked after the target has handled the QR_EC query
       request command pushed by the host.
Event: QR_EC is re-checked after the target has noticed the query event
       response data pulled by the host.
       This timing is not determined by any IRQs, so we may need to use a
       guard period in this mode, which may explain the existence of the
       ec_guard() code used by the old EC driver where the re-check timing
       is implemented in the similar way as this mode.
Method: QR_EC is re-checked as late as possible after completing the _Qxx
        evaluation. The target may implement SCI_EVT like a level triggered
        interrupt.
        It is proven on kernel bugzilla 94411 that, Windows will have all
        _Qxx evaluations parallelized. Thus unless required by further
        evidences, we needn't implement this mode as it is a conflict of
        the _Qxx parallelism requirement.

Note that, according to the reports, there are platforms that cannot be
handled using the "Status" mode without enabling the
EC_FLAGS_QUERY_HANDSHAKE quirk. But they can be handled with the other
modes according to the tests (kernel bugzilla 97381).

The following log entry can be used to confirm the differences of the 3
modes as it should appear at the different positions for the 3 modes:
  Command(QR_EC) unblocked
Status: appearing after
         EC_SC(W) = 0x84
Query: appearing after
         EC_DATA(R) = 0xXX
       where XX is the event number used to determine _QXX
Event: appearing after first
         EC_SC(R) = 0xX0 SCI_EVT=x BURST=0 CMD=0 IBF=0 OBF=0
       that is next to the following log entry:
         Command(QR_EC) completed by hardware

Link: https://bugzilla.kernel.org/show_bug.cgi?id=94411
Link: https://bugzilla.kernel.org/show_bug.cgi?id=97381
Link: https://bugzilla.kernel.org/show_bug.cgi?id=98111
Reported-and-tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reported-and-tested-by: Tigran Gabrielyan <tigrangab@gmail.com>
Reported-and-tested-by: Adrien D <ghbdtn@openmailbox.org>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-06-15 14:35:59 +02:00
Lv Zheng 9d8993be2d ACPI / EC: Convert event handling work queue into loop style.
During the period that a work queue is scheduled (queued up for run) but
hasn't been run, second schedule_work() could fail. This may not lead to
the loss of queries because QR_EC is always ensured to be submitted after
the work queue has been in the running state.

The event handling work queue can be changed into the loop style to allow
us to control the code in a more flexible way:
1. Makes it possible to add event=0x00 termination condition in the loop.
2. Increases the thoughput of the QR_EC transactions as the 2nd+ QR_EC
   transactions may be handled in the same work item used for the 1st QR_EC
   transaction, thus the delay caused by the 2nd+ work item scheduling can
   be eliminated.

Except the logging message changes and the throughput improvement, this
patch is just a funcitonal no-op.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Tested-by: Tigran Gabrielyan <tigrangab@gmail.com>
Tested-by: Adrien D <ghbdtn@openmailbox.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-06-15 14:35:59 +02:00
Lv Zheng f8b8eb7153 ACPI / EC: Cleanup transaction state transition.
This patch collects transaction state transition code into one function. We
then could have a single function to maintain transaction transition
related behaviors. No functional changes.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Tested-by: Tigran Gabrielyan <tigrangab@gmail.com>
Tested-by: Adrien D <ghbdtn@openmailbox.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-06-15 14:35:58 +02:00
Lv Zheng 3174abcfea ACPI / EC: Remove non-root-caused busy polling quirks.
{ Update to correct 1 patch subject in the description }

We have fixed a lot of race issues in the EC driver recently.

The following commit introduces MSI udelay()/msleep() quirk to MSI laptops
to make EC firmware working for bug 12011 without root causing any EC
driver race issues:
  Commit: 5423a0cb3f
  Subject: ACPI: EC: Add delay for slow MSI controller
  Commit: 34ff4dbccc
  Subject: ACPI: EC: Separate delays for MSI hardware

The following commit extends ECDT validation quirk to MSI laptops to make
EC driver locating EC registers properly for bug 12461:
  Commit: a5032bfdd9
  Subject: ACPI: EC: Always parse EC device
This is a different quirk than the MSI udelay()/msleep() quirk. This patch
keeps validating ECDT for only "Micro-Star MS-171F" as reported.

The following commit extends MSI udelay()/msleep() quirk to Quanta laptops
to make EC firmware working for bug 20242, there is no requirement to
validate ECDT for Quanta laptops:
  Commit: 534bc4e3d2 Mon Sep 17 00:00:00 2001
  Subject: ACPI EC: enable MSI workaround for Quanta laptops

The following commit extends MSI udelay()/msleep() quirk to Clevo laptops
to make EC firmware working for bug 77431, there is no requirement to
validate ECDT for Clevo laptops:
  Commit: 777cb38295
  Subject: ACPI / EC: Add msi quirk for Clevo W350etq

All udelay()/msleep() quirks for MSI/Quanta/Clevo seem to be the wrong
fixes generated without fixing the EC driver race issues.
And even if it is not wrong, the guarding can be covered by the following
commits in wait polling mode:
  Commit: 9e295ac14d
  Subject: ACPI / EC: Reduce ec_poll() by referencing the last register access timestamp.
  Commit: commit in the same series
  Subject: ACPI / EC: Fix and clean up register access guarding logics.
The only case that is not covered is the inter-transaction guarding. And
there is no evidence that we need the inter-transaction guarding upon
reading the noted bug entries.

So it is time to remove the quirks and let the users to try again. If there
is a regression, the only thing we need to do is to restore the
inter-transaction guarding for the reported platforms.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=12011
Link: https://bugzilla.kernel.org/show_bug.cgi?id=12461
Link: https://bugzilla.kernel.org/show_bug.cgi?id=20242
Link: https://bugzilla.kernel.org/show_bug.cgi?id=77431
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-05-16 01:53:03 +02:00
Lv Zheng 15de603b04 ACPI / EC: Add module params for polling modes.
We have 2 polling modes in the EC driver:
1. busy polling: originally used for the MSI quirks. udelay() is used to
   perform register access guarding.
2. wait polling: normal code path uses wait_event_timeout() and it can be
   woken up as soon as the transaction is completed in the interrupt mode.
   It also contains the register acces guarding logic in case the interrupt
   doesn't arrive and the EC driver is about to advance the transaction in
   task context (the polling mode).
The wait polling is useful for interrupt mode to allow other tasks to use
the CPU during the wait.
But for the polling mode, the busy polling takes less time than the wait
polling, because if no interrupt arrives, the wait polling has to wait the
minimal HZ interval.

We have a new use case for using the busy polling mode. Some GPIO drivers
initialize PIN configuration which cause a GPIO multiplexed EC GPE to be
disabled out of the GPE register's control. Busy polling mode is useful
here as it takes less time than the wait polling. But the guarding logic
prevents it from responding even faster. We should spinning around the EC
status rather than spinning around the nop execution lasted a determined
period.

This patch introduces 2 module params for the polling mode switch and the
guard time, so that users can use the busy polling mode without the
guarding in case the guarding is not necessary. This is an example to use
the 2 module params for this purpose:
  acpi.ec_busy_polling acpi.ec_polling_guard=0

We've tested the patch on a test platform. The platform suffers from such
kind of the GPIO PIN issue. The GPIO driver resets all PIN configuration
and after that, EC interrupt cannot arrive because of the multiplexing.
Then the platform suffers from a long delay carried out by the
wait_event_timeout() as all further EC transactions will run in the polling
mode. We switched the EC driver to use the busy polling mechanism instead
of the wait timeout polling mechanism and the delay is still high:
[   44.283005] calling  PNP0C0B:00+ @ 1305, parent: platform
[   44.417548] call PNP0C0B:00+ returned 0 after 131323 usecs
And this patch can significantly reduce the delay:
[   44.502625] calling  PNP0C0B:00+ @ 1308, parent: platform
[   44.503760] call PNP0C0B:00+ returned 0 after 1103 usecs

Tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-05-16 01:51:18 +02:00
Lv Zheng d8d031a605 ACPI / EC: Fix and clean up register access guarding logics.
In the polling mode, EC driver shouldn't access the EC registers too
frequently. Though this statement is concluded from the non-root caused
bugs (see links below), we've maintained the register access guarding
logics in the current EC driver. The guarding logics can be found here and
there, makes it hard to root cause real timing issues. This patch collects
the guarding logics into one single function so that all hidden logics
related to this can be seen clearly.

The current guarding related code also has several issues:
1. Per-transaction timestamp prevents inter-transaction guarding from being
   implemented in the same place. We have an inter-transaction udelay() in
   acpi_ec_transaction_unblocked(), this logic can be merged into ec_poll()
   if we can use per-device timestamp. This patch completes such merge to
   form a new ec_guard() function and collects all guarding related hidden
   logics in it.
   One hidden logic is: there is no inter-transaction guarding performed
   for non MSI quirk (wait polling mode), this patch skips
   inter-transaction guarding before wait_event_timeout() for the wait
   polling mode to reveal the hidden logic.
   The other hidden logic is: there is msleep() inter-transaction guarding
   performed when the GPE storming is observed. As after merging this
   commit:
     Commit: e1d4d90fc0
     Subject: ACPI / EC: Refine command storm prevention support
   EC_FLAGS_COMMAND_STORM is ensured to be cleared after invoking
   acpi_ec_transaction_unlocked(), the msleep() guard logic will never
   happen now. Since no one complains such change, this logic is likely
   added during the old times where the EC race issues are not fixed and
   the bugs are false root-caused to the timing issue. This patch simply
   removes the out-dated logic. We can restore it by stop skipping
   inter-transaction guarding for wait polling mode.
   Two different delay values are defined for msleep() and udelay() while
   they are merged in this patch to 550us.
2. time_after() causes additional delay in the polling mode (can only be
   observed in noirq suspend/resume processes where polling mode is always
   used) before advance_transaction() is invoked ("wait polling" log is
   added before wait_event_timeout()). We can see 2 wait_event_timeout()
   invocations. This is because time_after() ensures a ">" validation while
   we only need a ">=" validation here:
   [   86.739909] ACPI: Waking up from system sleep state S3
   [   86.742857] ACPI : EC: 2: Increase command
   [   86.742859] ACPI : EC: ***** Command(RD_EC) started *****
   [   86.742861] ACPI : EC: ===== TASK (0) =====
   [   86.742871] ACPI : EC: EC_SC(R) = 0x20 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=0
   [   86.742873] ACPI : EC: EC_SC(W) = 0x80
   [   86.742876] ACPI : EC: ***** Event started *****
   [   86.742880] ACPI : EC: ~~~~~ wait polling ~~~~~
   [   86.743972] ACPI : EC: ~~~~~ wait polling ~~~~~
   [   86.747966] ACPI : EC: ===== TASK (0) =====
   [   86.747977] ACPI : EC: EC_SC(R) = 0x20 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=0
   [   86.747978] ACPI : EC: EC_DATA(W) = 0x06
   [   86.747981] ACPI : EC: ~~~~~ wait polling ~~~~~
   [   86.751971] ACPI : EC: ~~~~~ wait polling ~~~~~
   [   86.755969] ACPI : EC: ===== TASK (0) =====
   [   86.755991] ACPI : EC: EC_SC(R) = 0x21 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=1
   [   86.755993] ACPI : EC: EC_DATA(R) = 0x03
   [   86.755994] ACPI : EC: ~~~~~ wait polling ~~~~~
   [   86.755995] ACPI : EC: ***** Command(RD_EC) stopped *****
   [   86.755996] ACPI : EC: 1: Decrease command
   This patch corrects this by using time_before() instead in ec_guard():
   [   54.283146] ACPI: Waking up from system sleep state S3
   [   54.285414] ACPI : EC: 2: Increase command
   [   54.285415] ACPI : EC: ***** Command(RD_EC) started *****
   [   54.285416] ACPI : EC: ~~~~~ wait polling ~~~~~
   [   54.285417] ACPI : EC: ===== TASK (0) =====
   [   54.285424] ACPI : EC: EC_SC(R) = 0x20 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=0
   [   54.285425] ACPI : EC: EC_SC(W) = 0x80
   [   54.285427] ACPI : EC: ***** Event started *****
   [   54.285429] ACPI : EC: ~~~~~ wait polling ~~~~~
   [   54.287209] ACPI : EC: ===== TASK (0) =====
   [   54.287218] ACPI : EC: EC_SC(R) = 0x20 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=0
   [   54.287219] ACPI : EC: EC_DATA(W) = 0x06
   [   54.287222] ACPI : EC: ~~~~~ wait polling ~~~~~
   [   54.291190] ACPI : EC: ===== TASK (0) =====
   [   54.291210] ACPI : EC: EC_SC(R) = 0x21 SCI_EVT=1 BURST=0 CMD=0 IBF=0 OBF=1
   [   54.291213] ACPI : EC: EC_DATA(R) = 0x03
   [   54.291214] ACPI : EC: ~~~~~ wait polling ~~~~~
   [   54.291215] ACPI : EC: ***** Command(RD_EC) stopped *****
   [   54.291216] ACPI : EC: 1: Decrease command

After cleaning up all guarding logics, we have one single function
ec_guard() collecting all old, non-root-caused, hidden logics. Then we can
easily tune the logics in one place to respond to the bug reports.

Except the time_before() change, all other changes do not change the
behavior of the EC driver.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=12011
Link: https://bugzilla.kernel.org/show_bug.cgi?id=20242
Link: https://bugzilla.kernel.org/show_bug.cgi?id=77431
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-05-16 01:51:18 +02:00
Lv Zheng 373783e6e9 ACPI / EC: Remove irqs_disabled() check.
The following commit merges polling and interrupt modes for EC driver:
  Commit: 2a84cb9852 Mon Sep 17 00:00:00 2001
  Subject: ACPI: EC: Merge IRQ and POLL modes
The irqs_disabled() check introduced in it tries to fall into busy polling
mode when the context of ec_poll() cannot sleep.

Actually ec_poll() is ensured to be invoked in the contexts that can sleep
(from a sysfs /sys/kernel/debug/ec/ec0/io access, or from
acpi_evaluate_object(), or from acpi_ec_gpe_poller()). Without the MSI
quirk, we never saw the udelay() logic invoked. Thus this check is useless
and can be removed.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-05-16 01:51:17 +02:00
Lv Zheng 5ab82a11e5 ACPI / EC: Remove storming threashold enlarging quirk.
This patch removes the storming threashold enlarging quirk.

After applying the following commit, we can notice that there is no no-op
GPE handling invocation can be observed, thus it is unlikely that the
no-op counts can exceed the storming threashold:
  Commit: ca37bfdfbc
  Subject: ACPI / EC: Fix several GPE handling issues by deploying ACPI_GPE_DISPATCH_RAW_HANDLER mode.
Even when the storming happens, we have already limited its affection to
the only transaction and no further transactions will be affected. This is
done by this commit:
  Commit: e1d4d90fc0
  Subject: ACPI / EC: Refine command storm prevention support

So it's time to remove this quirk.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=45151
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-05-16 01:51:17 +02:00
Lv Zheng 7c0b2595da ACPI / EC: Update acpi_ec_is_gpe_raised() with new GPE status flag.
This patch updates acpi_ec_is_gpe_raised() according to the following
commit:
  Commit: 09af8e8290
  Subject: ACPICA: Events: Add support to return both enable/status register values for GPE and fixed event.
This is actually a no-op change as both the flags are defined to a same
value.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-05-16 01:51:17 +02:00
Chris Bainbridge 6b5eab5469 ACPI / EC: fix NULL pointer dereference in acpi_ec_remove_query_handler()
Use list_for_each_entry_safe for iterating because handler may be freed
in the loop.

BUG: unable to handle kernel NULL pointer dereference at 000000000000002c
IP: [<ffffffff814d69c8>] acpi_ec_put_query_handler+0x7/0x1a
Call Trace:
 acpi_ec_remove_query_handler+0x87/0x97
 acpi_smbus_hc_remove+0x2a/0x44 [sbshc]
 acpi_device_remove+0x7b/0x9a
 __device_release_driver+0x7e/0x110
 driver_detach+0xb0/0xc0
 bus_remove_driver+0x54/0xe0
 driver_unregister+0x2b/0x60
 acpi_bus_unregister_driver+0x10/0x12
 acpi_smb_hc_driver_exit+0x10/0x12 [sbshc]
 SyS_delete_module+0x1b8/0x210
 system_call_fastpath+0x12/0x6a

Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-04-22 04:12:35 +02:00
Lan Tianyu 1c832b3e85 ACPI / EC: Call acpi_walk_dep_device_list() after installing EC opregion handler
On some machines(E,G Mircosoft surface 3), ACPI battery depends on
the EC operation region and it has _DEP method which contains EC.
Current code doesn't support such devices whose dep_unmet will be
not be decreased after EC opregion handler being installed. This
blocks battery device to be attached with its driver. This patch
is to fix the issue.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=90161
Reported-and-tested-by: Lompik <lompik@voila.fr>
Tested-by: Valentin Lab <valentin.lab_bugzilla.kernel.org@kalysto.org>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-04-02 02:21:41 +02:00
Lv Zheng 770970f0b4 ACPI / EC: Add GPE reference counting debugging messages.
This patch enhances debugging with the GPE reference count messages added.

This kind of log entries can be used by the platform validators to validate
if there is an EC transaction broken because of firmware/driver bugs.

No functional changes.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-03-10 00:58:37 +01:00
Lv Zheng 3535a3c126 ACPI / EC: Cleanup logging/debugging splitter support.
This patch refines logging/debugging splitter support so that when DEBUG is
disabled, splitters won't be visible in the kernel logs while they are
still available for developers when DEBUG is enabled.

This patch also refines the splitters to mark the following handling
process boundaries:
  +++++: boundary of driver starting/stopping
         boundary of IRQ storming
  =====: boundary of transaction advancement
  *****: boundary of EC command
         boundary of EC query
  #####: boundary of EC _Qxx evaluation

The following 2 log entries are originally logged using pr_info() in order
to be used as the boot/suspend/resume log entries for the EC device, this
patch also restores them to pr_info() logging level:
 ACPI : EC: EC started
 ACPI : EC: EC stopped

In this patch, one log entry around "Polling quirk" is converted into
ec_dbg_raw() which doesn't contain the boundary marker.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-03-10 00:58:36 +01:00
Scot Doyle 92e4b1bcd6 ACPI / EC: Remove non-standard log emphasis
Remove unusual pr_info() visual emphasis introduced in ad479e7f47
"ACPI / EC: Introduce STARTED/STOPPED flags to replace BLOCKED flag".

Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
[ rjw: Change pr_info() to pr_debug() too in those places. ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-02-17 18:27:59 +01:00
Rafael J. Wysocki 37d11391c2 Revert "ACPI / EC: Add query flushing support"
Revert commit f252cb09e1 (ACPI / EC: Add query flushing support),
because it breaks system suspend on Acer Aspire S5.  The machine
just hangs solid at the last stage of suspend (after taking non-boot
CPUs offline).

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-02-11 17:35:05 +01:00
Rafael J. Wysocki e06bf91b59 Revert "ACPI / EC: Add GPE reference counting debugging messages"
Revert commit b5bca896ef (ACPI / EC: Add GPE reference counting
debugging messages), because it depends on commit f252cb09e1
(ACPI / EC: Add query flushing support) which breaks system suspend
on Acer Aspire S5 and needs to be reverted.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-02-11 17:33:23 +01:00
Lv Zheng b5bca896ef ACPI / EC: Add GPE reference counting debugging messages
This patch enhances debugging with the GPE reference count messages added.
No functional changes.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-02-06 15:48:10 +01:00
Lv Zheng f252cb09e1 ACPI / EC: Add query flushing support
This patch implementes the QR_EC flushing support.

Grace periods are implemented from the detection of an SCI_EVT to the
submission/completion of the QR_EC transaction. During this period, all
EC command transactions are allowed to be submitted.

Note that query periods and event periods are intentionally distiguished to
allow further improvements.
1. Query period: from the detection of an SCI_EVT to the sumission of the
   QR_EC command. This period is used for storming prevention, as currently
   QR_EC is deferred to a work queue rather than directly issued from the
   IRQ context even there is no other transactions pending, so malicous
   SCI_EVT GPE can act like "level triggered" to trigger a GPE storm. We
   need to be prepared for this. And in the future, we may change it to be
   a part of the advance_transaction() where we will try QR_EC submission
   in appropriate positions to avoid such GPE storming.
2. Event period: from the detection of an SCI_EVT to the completion of the
   QR_EC command. We may extend it to the completion of _Qxx evaluation.
   This is actually a grace period for event flushing, but we only flush
   queries due to the reason stated in known issue 1. That's also why we
   use EC_FLAGS_EVENT_xxx. During this period, QR_EC transactions need to
   pass the flushable submission check.

In this patch, the following flags are implemented:
1. EC_FLAGS_EVENT_ENABLED: this is derived from the old
   EC_FLAGS_QUERY_PENDING flag which can block SCI_EVT handlings.
   With this flag, the logics implemented by the original flag are
   extended:
   1. Old logic: unless both of the flags are set, the event poller will
                 not be scheduled, and
   2. New logic: as soon as both of the flags are set, the evet poller will
                 be scheduled.
2. EC_FLAGS_EVENT_DETECTED: this is also derived from the old
   EC_FLAGS_QUERY_PENDING flag which can block SCI_EVT detection. It thus
   can be used to indicate the storming prevention period for query
   submission.
   acpi_ec_submit_request()/acpi_ec_complete_request() are invoked to
   implement this period so that acpi_set_gpe() can be invoked under the
   "reference count > 0" condition.
3. EC_FLAGS_EVENT_PENDING: this is newly added to indicate the grace period
   for event flushing (query flushing for now).
   acpi_ec_submit_request()/acpi_ec_complete_request() are invoked to
   implement this period so that the flushing process can wait until the
   event handling (query transaction for now) to be completed.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=82611
Link: https://bugzilla.kernel.org/show_bug.cgi?id=77431
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Tested-by: Ortwin Glück <odi@odi.ch>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-02-06 15:48:10 +01:00
Lv Zheng e1d4d90fc0 ACPI / EC: Refine command storm prevention support
This patch refines EC command storm prevention support.

Current command storming code is wrong, when the storming condition is
detected, it only flags the condition without doing anything for the
current command but performing storming prevention for the follow-up
commands. So:
1. The first command which suffers from the storming still suffers from
   storming.
2. The follow-up commands which may not suffer from the storming are
   unconditionally forced into the storming prevention mode.
Ideally, we should only enable storm prevention immediately after detection
for the current command so that the next command can try the
power/performance efficient interrupt mode again.

This patch improves the command storm prevention by disabling GPE right
after the detection and re-enabling it right before completing the command
transaction using the GPE storming prevention APIs. This thus deploys the
following GPE handling model:
1. acpi_enable_gpe()/acpi_disable_gpe() for reference count changes:
   This set of APIs are used for EC usage reference counting.
2. acpi_set_gpe(ACPI_GPE_ENABLE)/acpi_set_gpe(ACPI_GPE_DISABLE):
   This set of APIs are used for preventing GPE storm. They must be invoked
   when the reference count > 0.
   Note that as the storming prevention should always happen when there is
   an outstanding request, or GPE enabling value will be messed up by the
   races. This patch also adds BUG_ON() to enforces this rule to prevent
   future bugs.

The msleep(1) used after completing a transaction is useless now as this
sounds like a guard time only useful for platforms that need the
EC_FLAGS_MSI quirks while we have fixed GPE race issues using the previous
raw handler mode enabling. It is kept to avoid regressions. A seperate
patch which deletes EC_FLAGS_MSI quirks should take care of deleting it.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-02-06 15:48:09 +01:00