Move of_register_spi_devices() call from drivers to
spi_register_master(). Also change the function to use
the struct device_node pointer from master spi device
instead of passing it as function argument.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
spi_t was removed in commit 644b2a680c
("powerpc/cpm: Remove SPI defines and spi structs"), the commit assumed
that spi_t isn't used anywhere outside of the spi_mpc8xxx driver. But
it appears that the struct is needed for micropatch code. So, let's
reintroduce the struct.
Fixes the following build issue:
CC arch/powerpc/sysdev/micropatch.o
micropatch.c: In function 'cpm_load_patch':
micropatch.c:629: error: expected '=', ',', ';', 'asm' or '__attribute__' before '*' token
micropatch.c:629: error: 'spp' undeclared (first use in this function)
micropatch.c:629: error: (Each undeclared identifier is reported only once
micropatch.c:629: error: for each function it appears in.)
Reported-by: LEROY Christophe <christophe.leroy@c-s.fr>
Reported-by: Tony Breeds <tony@bakeyournoodle.com>
Cc: <stable@kernel.org> [ .33, .34 ]
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This fixes a typo were map_tx_dma is used instead of
map_rx_dma, casing the driver to unmap rx_dma when it
shouldn't.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
QE mode uses Little Endian so words > 8 bits are byte swapped.
Workaround this by always enforcing wordsize 8 for words
> 8 bits. Unfortunately this will not work for LSB transfers
where wordsize is > 8 bits so disable these for now.
Also move the different quirks into its own function to keep
mpc8xxx_spi_setup_transfer() sane.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
tx_dma/rx_dma are already set to a dummy buffer when no
tx/rx buffer and t->tx_dma/t->rx_dma does not contain a dma
address, but NULL.
This may lead to corruption of kernel memory. Fix this by
leaving tx_dma/rx_dma alone.
Do not INIT_TX_RX while controller is enabled, this is bad according
to the MPC8321 manual.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Correct SPI clock frequency division factor rounding, preventing clock rates
higher than the maximum specified clock frequency being used.
When specifying spi-max-frequency = <10000000> in the device tree,
the resulting frequency was 11.1 MHz, with spibrg being 133333332.
According to the freescale data sheet [1], the spi clock rate is
spiclk = spibrg / (4 * (pm+1))
The existing code calculated
pm = mpc8xxx_spi->spibrg / (hz * 4); pm--;
resulting in pm = (int) (3.3333) - 1 = 2,
resulting in spiclk = 133333332/(4*(2+1)) = 11111111
With the fix,
pm = (mpc8xxx_spi->spibrg - 1) / (hz * 4) + 1; pm--;
resulting in pm = (int) (4.3333) - 1 = 3,
resulting in spiclk = 133333332/(4*(3+1)) = 8333333
Without the fix, for every desired SPI frequency that
is not exactly derivable from spibrg, pm will be too
small due to rounding down, resulting in a too high SPI clock,
so we need a pm which is one higher.
For values that are exactly derivable, spibrg will
be dividable by (hz*4) without remainder, and
(int) ((spibrg-1)/(hz*4)) will be one lower than
(int) (spibrg)/(hz*4), which is compensated by adding 1.
For these values, the fixed version calculates the same pm
as the unfixed version.
For all values that are not exactly derivable,
spibrg will be not dividable by (hz*4) without
remainder, and (int) ((spibrg-1)/(hz*4)) will be
the same as (int) (spibrg)/(hz*4), and the calculated pm will
be one higher than calculated by the unfixed version.
References:
[1] http://www.freescale.com/files/32bit/doc/ref_manual/MPC8315ERM.pdf,
page 22-10 -> 1398
Signed-off-by: Ernst Schwab <eschwab@online.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
platform_get_irq returns -ENXIO on failure, so !irq was probably
always true. Make irq a signed variable and compare irq <= 0. Note
that a return value of zero is still handled as error even though this
could mean irq0.
This is a followup to 305b3228f9 that
changed the return value of platform_get_irq from 0 to -ENXIO on error.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi: spi_txx9.c: use resource_size()
spi: spi_sh_sci.c: use resource_size()
spi: spi_mpc8xxx.c: use resource_size()
spi: spi_bfin5xx.c: use resource_size()
spi: atmel_spi.c: use resource_size()
spi: Add s3c64xx SPI Controller driver
atmel_spi: fix dma addr calculation for len > BUFFER_SIZE
spi_s3c24xx: add FIQ pseudo-DMA support
spi: controller driver for Designware SPI core
spidev: add proper section markers
spidev: use DECLARE_BITMAP instead of declaring the array
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (23 commits)
spi: fix probe/remove section markings
Add OMAP spi100k driver
spi-imx: don't access struct device directly but use dev_get_platdata
spi-imx: Add mx25 support
spi-imx: use positive logic to distinguish cpu variants
spi-imx: correct check for platform_get_irq failing
ARM: NUC900: Add spi driver support for nuc900
spi: SuperH MSIOF SPI Master driver V2
spi: fix spidev compilation failure when VERBOSE is defined
spi/au1550_spi: fix setupxfer not to override cfg with zeros
spi/mpc8xxx: don't use __exit_p to wrap plat_mpc8xxx_spi_remove
spi/i.MX: fix broken error handling for gpio_request
spi/i.mx: drain MXC SPI transfer buffer when probing device
MAINTAINERS: add SPI co-maintainer.
spi/xilinx_spi: fix incorrect casting
spi/mpc52xx-spi: minor cleanups
xilinx_spi: add a platform driver using the xilinx_spi common module.
xilinx_spi: add support for the DS570 IP.
xilinx_spi: Switch to iomem functions and support little endian.
xilinx_spi: Split into of driver and generic part.
...
The function plat_mpc8xxx_spi_remove is defined using __devexit, so don't
use __exit_p but __devexit_p to wrap it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit 87ec0e98cf in kumar's next branch
broke one of my test configs since it looks like Anton forgot about
that mpc832x_rdb platform which still uses the old style probing for
the SPI stuff.
I'll let them do a cleaner fix that probably involves changing the
probing method and getting rid of the platform device but for now
this will do to fix it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds QE buffer descriptors mode support for the
spi_mpc8xxx driver, and as a side effect we now support CPM1
and CPM2 SPI controllers.
That means that today we support almost all MPC SPI controllers:
- MPC834x-style controllers (support PIO mode only);
- CPM1 and CPM2 controllers (support DMA mode only);
- QE SPI controllers in CPU mode (PIO mode with shift quirks);
- QE SPI controllers in buffer descriptors (DMA) mode;
The only controller we don't currently support is a newer eSPI
(with a dedicated chip selects and a bit different registers map).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Soon there will be more flags introduced in subsequent patches, so
let's turn qe_mode into flags.
Also introduce mpc8xxx_spi_strmode() and print current SPI mode.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We'll add more steps soon, so get rid of the duplication.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes the following warning:
CC drivers/spi/spi_mpc8xxx.o
spi_mpc8xxx.c: In function 'of_mpc8xxx_spi_probe':
spi_mpc8xxx.c:681: warning: 'ret' may be used uninitialized in this function
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since we renamed the file, we might want to rename the file internals too.
Though we don't bother with changing platform driver name and platform
module alias. The stuff is legacy and hopefully we'll remove it soon.
Suggested-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver handles MPC83xx, MPC85xx and MPC86xx SPI controllers, so rename
the file for clarity.
Suggested-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anatolij Gustschin
Anton Vorontsov
Grant Likely
Joakim Tjernlund
Jiri Kosina
Tejun Heo
Thomas Weber
Ernst Schwab
Uwe Kleine-König
Linus Torvalds
hartleys
Benjamin Herrenschmidt
Anton Vorontsov