The xHCI driver issues a Configure Endpoint command for two reasons:
- a new configuration or alternate interface setting is selected
- a quirky Fresco Logic prototype requires the command after a Reset
Endpoint command.
The xHCI driver only waits on the command in the first case.
When a configure endpoint command completes, the driver needs to know why
the command was generated. When the driver only supported selecting an
initial configuration, the check was simple. Unfortunately that check
doesn't work now that the driver supports alternate interfaces. If an
endpoint must be dropped (because it's not in the new alternate setting)
and no new endpoints are added, the math involving
xhci_last_valid_endpoint() will assign -1 to an unsigned integer and cause
an out-of-bounds array access.
Move the check for the quirky hardware sooner and avoid the bad array
access.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a driver wants to switch to a different alternate setting for an
interface, the USB core will (soon) check whether there is enough
bandwidth. Once the new alternate setting is installed in the xHCI
hardware, the USB core will send a USB_REQ_SET_INTERFACE control
message. That can fail in various ways, and the USB core needs to be
able to reinstate the old alternate setting.
With the old code, reinstating the old alt setting could fail if the
there's not enough memory to allocate new endpoint rings. Keep
around a cache of (at most 31) endpoint rings for this case. When we
successfully switch the xHCI hardware to the new alt setting, the old
alt setting's rings will be stored in the cache. Therefore we'll
always have enough rings to satisfy a conversion back to a previous
device setting.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When building qTDs (sTDs) from a scatter-gather list, the length of the
qTD must be a multiple of wMaxPacketSize if the transfer continues into
another qTD.
This also fixes a link failure on configurations for 32 bit processors
with 64 bit dma_addr_t (e.g., CONFIG_HIGHMEM_64G).
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xHCI 0.95 and 0.96 specification defines several transfer buffer
request completion codes that indicate a USB transaction error occurred.
When a stall, babble, transaction, or split transaction error completion code
is set, the xHCI has halted that endpoint ring. Software must issue a
Reset Endpoint command and a Set Transfer Ring Dequeue Pointer command
to clean up the halted ring.
The USB device driver is supposed to call into usb_reset_endpoint() when
an endpoint stalls. That calls into the xHCI driver to issue the proper
commands. However, drivers don't call that function for the other
errors that cause the xHC to halt the endpoint ring. If a babble,
transaction, or split transaction error occurs, check if the endpoint
context reports a halted condition, and clean up the endpoint ring if it
does.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An xHCI host controller manufacturer can choose to implement several
vendor-specific informational completion codes. These are all to be
treated like a successful transfer completion.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the xHCI hardware says a transfer completed with a split
transaction error, set the URB status to -EPROTO.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The transfer descriptor (TD) is a series of transfer request buffers
(TRBs) that describe the buffer pointer, length, and other
characteristics. The xHCI controllers want to know an estimate of how
long the TD is, for caching reasons. In each TRB, there is a "TD size"
field that provides a rough estimate of the remaining buffers to be
transmitted, including the buffer pointed to by that TRB.
The TD size is 5 bits long, and contains the remaining size in bytes,
right shifted by 10 bits. So a remaining TD size less than 1024 would get
a zero in the TD size field, and a remaining size greater than 32767 would
get 31 in the field.
This patches fixes a bug in the TD_REMAINDER macro that is triggered when
the URB has a scatter gather list with a size bigger than 32767 bytes.
Not all host controllers pay attention to the TD size field, so the bug
will not appear on all USB 3.0 hosts.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's not surprising that the transfer request buffer (TRB) physical to
virtual address translation function has bugs in it, since I wrote most of
it at 4am last October. Add a test suite to check the TRB math. This
runs at memory initialization time, and causes the driver to fail to load
if the TRB math fails.
Please excuse the excessively long lines in the test vectors; they can't
really be made shorter and still be readable.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
td and dev can not be null.
Also they are dereferenced in list_for_each_entry_safe and list_for_each
before the check happens so we would have an oops if it were possible
for them to be null.
Found using the smatch static checker.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
istl_flip is a signed bitfield of one bit so it can be -1 or 0.
However in drivers/usb/host/isp1362-hcd.c:1103:
finish_iso_transfers(isp1362_hcd,
&isp1362_hcd->istl_queue[isp1362_hcd->istl_flip]);
So if isp1362_hcd->istl_flip is set, the 2nd argument becomes
&isp1362_hcd->istl_queue[-1], which is invalid.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1300) adds native scatter-gather support to ehci-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Freescale MX27 and MX31 SoCs have a EHCI controller onboard.
The controller is capable of USB on the go. This patch adds
a driver to support all three of them.
Users have to pass details about serial interface configuration in the
platform data.
The USB OTG core used here is the ARC core, so the driver should
be renamed and probably be merged with ehci-fsl.c eventually.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The EHCI specification says that an EHCI host controller may cache part of
the isochronous schedule. The EHCI controller must advertise how much it
caches in the schedule through the HCCPARAMS register isochronous
scheduling threshold (IST) bits.
In theory, adding new iTDs within the IST should be harmless. The HW will
follow the old cached linked list and miss the new iTD. SW will notice HW
missed the iTD and return 0 for the transfer length.
However, Intel ICH9 chipsets (and some later chipsets) have issues when SW
attempts to schedule a split transaction within the IST. All transfers
will cease being sent out that port, and the drivers will see isochronous
packets complete with a length of zero. Start of frames may or may not
also disappear, causing the device to go into auto-suspend. This "bus
stall" will continue until a control or bulk transfer is queued to a
device under that roothub.
Most drivers will never cause this behavior, because they use multiple
URBs with multiple packets to keep the bus busy. If you limit the number
of URBs to one, you may be able to hit this bug.
Make sure the EHCI driver does not schedule full-speed transfers within
the IST under an Intel chipset. Make sure that when we fall behind the
current microframe plus IST, we schedule the new transfer at the next
periodic interval after the IST.
Don't change the scheduling for new transfers, since the schedule slop will
always be greater than the IST. Allow high speed isochronous transfers to
be scheduled within the IST, since this doesn't trigger the Intel chipset
bug.
Make sure that if the host caches the full frame, the EHCI driver's
internal isochronous threshold (ehci->i_thresh) is set to
8 microframes + 2 microframes wiggle room. This is similar to what is done in
the case where the host caches less than the full frame.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change the constant SCHEDULE_SLOP to be 80 microframes, instead of 10
frames. It was always multiplied by 8 to convert frames to microframes.
SCHEDULE_SLOP is only used in ehci-sched.c.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CONFIG_USB_HCD_STAT was used in an abandoned patch to track host
controller throughput statistics. Since CONFIG_USB_HCD_STAT will never be
defined, remove code that can never run.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In order to giveback a canceled URB, we must ensure that the xHCI
hardware will not access the buffer in an URB. We can't modify the
buffer pointers on endpoint rings without issuing and waiting for a stop
endpoint command. Since URBs can be canceled in interrupt context, we
can't wait on that command. The old code trusted that the host
controller would respond to the command, and would giveback the URBs in
the event handler. If the hardware never responds to the stop endpoint
command, the URBs will never be completed, and we might hang the USB
subsystem.
Implement a watchdog timer that is spawned whenever a stop endpoint
command is queued. If a stop endpoint command event is found on the
event ring during an interrupt, we need to stop the watchdog timer with
del_timer(). Since del_timer() can fail if the timer is running and
waiting on the xHCI lock, we need a way to signal to the timer that
everything is fine and it should exit. If we simply clear
EP_HALT_PENDING, a new stop endpoint command could sneak in and set it
before the watchdog timer can grab the lock.
Instead we use a combination of the EP_HALT_PENDING flag and a counter
for the number of pending stop endpoint commands
(xhci_virt_ep->stop_cmds_pending). If we need to cancel the watchdog
timer and del_timer() succeeds, we decrement the number of pending stop
endpoint commands. If del_timer() fails, we leave the number of pending
stop endpoint commands alone. In either case, we clear the
EP_HALT_PENDING flag.
The timer will decrement the number of pending stop endpoint commands
once it obtains the lock. If the timer is the tail end of the last stop
endpoint command (xhci_virt_ep->stop_cmds_pending == 0), and the
endpoint's command is still pending (EP_HALT_PENDING is set), we assume
the host is dying. The watchdog timer will set XHCI_STATE_DYING, try to
halt the xHCI host, and give back all pending URBs.
Various other places in the driver need to check whether the xHCI host
is dying. If the interrupt handler ever notices, it should immediately
stop processing events. The URB enqueue function should also return
-ESHUTDOWN. The URB dequeue function should simply return the value
of usb_hcd_check_unlink_urb() and the watchdog timer will take care of
giving the URB back. When a device is disconnected, the xHCI hardware
structures should be freed without issuing a disable slot command (since
the hardware probably won't respond to it anyway). The debugging
polling loop should stop polling if the host is dying.
When a device is disconnected, any pending watchdog timers are killed
with del_timer_sync(). It must be synchronous so that the watchdog
timer doesn't attempt to access the freed endpoint structures.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xhci_quiesce() is basically a no-op right now. It's only called if
HC_IS_RUNNING() is true, and the body of the function consists of a
BUG_ON if HC_IS_RUNNING() is false. For the new xHCI watchdog timer, we
need a new function that clears the xHCI running bit in the command
register, but doesn't wait for the halt status to show up in the status
register. Re-purpose xhci_quiesce() to do that.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the old code, there was a race condition between the stop endpoint
command and the URB submission process. When the stop endpoint command is
handled by the event handler, the endpoint ring is assumed to be stopped.
When a stop endpoint command is queued, URB submissions are to not ring
the doorbell. The old code would check the number of pending URBs to be
canceled, and would not ring the doorbell if it was non-zero.
However, the following race condition could occur with the old code:
1. Cancel an URB, add it to the list of URBs to be canceled, queue the stop
endpoint command, and increment ep->cancels_pending to 1.
2. The URB finishes on the HW, and an event is enqueued to the event ring
(at the same time as 1).
3. The stop endpoint command finishes, and the endpoint is halted. An
event is queued to the event ring.
4. The event handler sees the finished URB, notices it was to be
canceled, decrements ep->cancels_pending to 0, and removes it from the to
be canceled list.
5. The event handler drops the lock and gives back the URB. The
completion handler requeues the URB (or a different driver enqueues a new
URB). This causes the endpoint's doorbell to be rung, since
ep->cancels_pending == 0. The endpoint is now running.
6. A second URB is canceled, and it's added to the canceled list.
Since ep->cancels_pending == 0, a new stop endpoint command is queued, and
ep->cancels_pending is incremented to 1.
7. The event handler then sees the completed stop endpoint command. The
handler assumes the endpoint is stopped, but it isn't. It attempts to
move the dequeue pointer or change TDs to cancel the second URB, while the
hardware is actively accessing the endpoint ring.
To eliminate this race condition, a new endpoint state bit is introduced,
EP_HALT_PENDING. When this bit is set, a stop endpoint command has been
queued, and the command handler has not begun to process the URB
cancellation list yet. The endpoint doorbell should not be rung when this
is set. Set this when a stop endpoint command is queued, clear it when
the handler for that command runs, and check if it's set before ringing a
doorbell. ep->cancels_pending is eliminated, because it is no longer
used.
Make sure to ring the doorbell for an endpoint when the stop endpoint
command handler runs, even if the canceled URB list is empty. All
canceled URBs could have completed and new URBs could have been enqueued
without the doorbell being rung before the command was handled.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this driver has been sitting in linux-omap tree for quite
some time. It adds support for omap's ehci controller.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the wusb_phy_rate sysfs file to Wireless USB host controllers. This
sets the maximum PHY rate that will be used for all connected devices.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Print ep number, direction and type; and current window in asl and pzl
debugfs files.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify both host and gadget USB drivers for at91sam9g10.
This add a clock management equivalent to at91sam9261 on usb drivers.
It also add the way of handling gadget pull-ups (like the at91sam9261).
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fix type and format warning in the new sg code. Remove the very chatty
debug messages that were left in by mistake and use min_t() as required
(no one seems to agree on a type for buffer sizes).
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support urbs with scatter-gather lists by trying to fit sg list elements
into page lists in one or more qTDs. qTDs must end on a wMaxPacketSize
boundary so if this isn't possible the urb's sg list must be copied into
bounce buffers.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The WHCI HCD will also support urbs with scatter-gather lists. Add a
usb_bus field to indicated how many sg list elements are supported by
the HCD. Use this to decide whether to pass the scatter-list to the HCD
or not.
Make the usb-storage driver use this new field.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I can't see any reason why these would not be static.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add bus glue driver for Xilinx USB host controller. The controller can be
configured as HS only or HS/FS hybrid. The driver uses the device tree file
to configure the driver according to the setting in the hardware system.
This driver has been tested with usbtest using the NET2280 PCI card.
Signed-off-by: Julie Zhu <julie.zhu@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No need to check ehci->debug twice.
Found-by: Sergei Shtylyov sshtylyov@ru.mvista.com
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
a quirky chipset needs periodic schedules to run for a minimum
time before they can be disabled again. This enforces the requirement
with a time stamp and a calculated delay
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1304) fixes a regression in ehci-hcd. Evidently some
hubs don't handle Clear-TT-Buffer requests correctly, so we should
avoid sending them when they don't appear to be absolutely necessary.
The reported symptom is that output on a downstream audio device cuts
out because the hub stops relaying isochronous packets.
The patch prevents Clear-TT-Buffer requests from being sent following
a STALL handshake. In theory a STALL indicates either that the
downstream device sent a STALL or that no matching TT buffer could be
found. In either case, the transfer is completed and the TT buffer
does not remain busy, so it doesn't need to be cleared.
Also, the patch fixes a minor flaw in the code that actually sends the
Clear-TT-Buffer requests. Although the pipe direction isn't really
used for control transfers, it should be a Send rather than a Receive.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Javier Kohen <jkohen@users.sourceforge.net>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Most of the irq_req_t typedef'd struct can be re-worked quite
easily:
(1) IRQInfo2 was unused in any case, so drop it.
(2) IRQInfo1 was used write-only, so drop it.
(3) Instance (private data to be passed to the IRQ handler):
Most PCMCIA drivers using pcmcia_request_irq() to actually
register an IRQ handler set the "dev_id" to the same pointer
as the "priv" pointer in struct pcmcia_device. Modify the two
exceptions (ipwireless, ibmtr_cs) to also work this waym and
set the IRQ handler's "dev_id" to p_dev->priv unconditionally.
(4) Handler is to be of type irq_handler_t.
(5) Handler != NULL already tells whether an IRQ handler is present.
Therefore, we do not need the IRQ_HANDLER_PRESENT flag in
irq_req_t.Attributes.
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-scsi@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: Jaroslav Kysela <perex@perex.cz>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Karsten Keil <isdn@linux-pingi.de>
for the Bluetooth parts: Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The scratchpad_free() function uses xhci->page_size to free some memory
with pci_free_consistent(). However, the page_size is set to zero before
the call, causing kernel oopses on driver unload. Call scratchpad_free()
before setting xhci->page_size to zero.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: John Youn <John.Youn@synopsys.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The trb_in_td() function in the xHCI driver is supposed to translate a
physical transfer buffer request (TRB) into a virtual pointer to the ring
segment that TRB is in.
Unfortunately, a mistake in this function may cause endless loops as the
driver searches through the linked list of ring segments over and over
again. Fix a couple bugs that may lead to loops or bad output:
1. Bail out if we get a NULL pointer when translating the segment's
private structure and the starting DMA address of the segment chunk. If
this happens, we've been handed a starting TRB pointer from a different
ring.
2. Make sure the function works when there's multiple segments in the
ring. In the while loop to search through the ring segments, use the
current segment variable (cur_seg), rather than the starting segment
variable (start_seg) that is passed in.
3. Stop searching the ring if we've run through all the segments in the
ring.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the xHCI driver fails during the memory initialization, xhci->ir_set
may not be a valid pointer. Check that it points to valid DMA'able memory
before writing to that address during the memory freeing process.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch in the driver is required to avoid USB 1.1 device
failures that may occur due to requests from USB OHCI controllers may
be overwritten if the latency for any pending request by the USB
controller is very long (in the range of milliseconds).
Signed-off-by: Libin Yang <libin.yang@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert PCMCIA drivers to use the dynamic debug infrastructure, instead of
requiring manual settings of PCMCIA_DEBUG.
Also, remove all usages of the CS_CHECK macro and replace them with proper
Linux style calling and return value checking. The extra error reporting may
be dropped, as the PCMCIA core already complains about any (non-driver-author)
errors.
CC: linux-mtd@lists.infradead.org
CC: linux-usb@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
When the EHCI driver falls behind in its scheduling, the active stream's
first empty microframe may be in the past with respect to the current
microframe. The code attempts to move the starting microframe ("start") N
number of microframes forward, where N is the interval of endpoint.
However, stream->interval is a copy of the endpoint's bInterval, which is
designated in frames for FS devices, and microframes for HS devices.
Convert stream->interval to microframes before using it to move the
starting microframe forward.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A halted qTD always triggers a hardware list update because the qset was
either removed or reactivated.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If an endpoint is deleted before it's been fully added to the hardware
list, the associated qset will not be fully initialized and an oops will
occur when complete(&qset->remove_complete) is called. This can happen
if a queued URB is cancelled.
Fix this by only removing the qset from the hardware list if the
cancelled URB had qTDs.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit db8be50c43, as per
http://bugzilla.kernel.org/show_bug.cgi?id=14374http://marc.info/?l=linux-kernel&m=125446885705223&w=4
We simply can't do the USB handoff at FIXUP_HEADER time, since it will
often require us to have valid IO mappings etc. But that in turn
requires a whole different approach, not this trivial one-liner.
Maybe we could teach all the USB quirk handoff handlers to only do the
quirk if the device has all its registers set up (since if it isn't
initialized, it's unlikely to be active), but regardless that will need
a whole lot more code than just saying "let's do it really early".
The proper fix is almost certainly to just leave the legacy IOMMU
mappings active until after all devices have been initialized.
Reported-by: Nick Piggin <npiggin@suse.de>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The EHCI driver does some bounds checking when it's scheduling an iTD for
an active endpoint. It sets the local variable start to
stream->next_uframe and moves that variable further in the schedule if
necessary. However, the driver fails to do anything with start before
jumping to the ready label and setting the URB's starting frame to
stream->next_uframe. Alan Stern confirms the EHCI driver should set
stream->next_uframe to start before jumping.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A bunch of places assumed pointers were 32-bits in size (bit checking and
debug output), but none of these affected runtime functionality.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When an endpoint is to be dropped from the hardware bandwidth schedule, we
want to clear its add flag.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the host controller dies or is removed while a device is plugged in,
the USB core will attempt to deallocate the struct usb_device. That will
call into xhci_free_dev(). This function used to attempt to submit a
disable slot command to the host controller and clean up the device
structures when that command returned. Change xhci_free_dev() to skip the
command submission and just free the memory if the host controller died.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the host controller dies (e.g. it is removed from a PCI card slot),
the xHCI driver cannot expect commands to complete. The buggy code this
patch fixes would mark an URB as canceled and then expect the URB to be
completed when the stop endpoint command completed. That would never
happen if the host controller was dead, so the USB core would just hang in
the disconnect code.
If the host controller died, and the driver asks to cancel an URB, free
any structures associated with that URB and immediately give it back.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the host controller card is removed from the system, stop the timer
function to debug the xHCI rings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a hook for updating xHCI internal structures after khubd fetches the
hub descriptor and sets up the hub's TT information. The xHCI driver must
update the internal structures before devices under the hub can be
enumerated.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For a USB hub to work under an xHCI host controller, the xHC's internal
scheduler must be made aware of the hub's characteristics. Add an xHCI
hook that the USB core will call after it fetches the hub descriptor.
This hook will add hub information to the slot context for that device,
including whether it has multiple TTs or a single TT, the number of ports
on the hub, and TT think time.
Setting up the slot context for the device is different for 0.95 and 0.96
xHCI host controllers.
Some of the slot context reserved fields in the 0.95 specification were
changed into hub fields in the 0.96 specification. Don't set the TT think
time or number of ports for a hub if we're dealing with a 0.95-compliant
xHCI host controller.
The 0.95 xHCI specification says that to modify the hub flag, we need to
issue an evaluate context command. The 0.96 specification says that flag
can be set with a configure endpoint command. Issue the correct command
based on the version reported by the hardware.
This patch does not add support for multi-TT hubs. Multi-TT hubs expose
a single TT on alt setting 0, and multi-TT on alt setting 1. The xHCI
driver can't handle setting alternate interfaces yet.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When setting up a slot context for an address device command, set the
multi-TT field if this is a low or full speed device under a HS hub with
multiple transaction translators.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xHCI driver needs to set the route string in the slot context of all
devices, not just SuperSpeed devices. The route string concept was added
in the USB 3.0 specification, section 10.1.3.2. Each hub in the topology
is expected to have no more than 15 ports in order for the route string of
a device to be unique. SuperSpeed hubs are restricted to only having 15
ports, but FS/LS/HS hubs are not. The xHCI specification says that if the
port number the device is under is greater than 15, that portion of the
route string shall be set to 15.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the xHCI driver, configure endpoint commands that are submitted to the
hardware may involve one of two data structures. If the configure
endpoint command is setting up a new configuration or modifying max packet
sizes, the data structures and completions are statically allocated in the
xhci_virt_device structure. If the command is being used to set up
streams or add hub information, then the data structures are dynamically
allocated, and placed on a device command waiting list.
Break out the code to check whether a completed command is in the device
command waiting list. Fix a subtle bug in the old code: continue
processing the command if the command isn't in the wait list. In the old
code, if there was a command in the wait list, but it didn't match the
completed command, the completed command event would be dropped.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some commands to the xHCI hardware cannot be allowed to fail due to out of
memory issues or the command ring being full.
Add a way to reserve a TRB on the command ring, and make all command
queueing functions indicate whether they are using a reserved TRB.
Add a way to pre-allocate all the memory a command might need. A command
needs an input context, a variable to store the status, and (optionally) a
completion for the caller to wait on. Change all code that assumes the
input device context, status, and completion for a command is stored in
the xhci virtual USB device structure (xhci_virt_device).
Store pending completions in a FIFO in xhci_virt_device. Make the event
handler for a configure endpoint command check to see whether a pending
command in the list has completed. We need to use separate input device
contexts for some configure endpoint commands, since multiple drivers can
submit requests at the same time that require a configure endpoint
command.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Refactor common code to set up the add and drop flags for the input device
context setup. This setup is used before a configure endpoint command for
the reset endpoint quirk, and will be used for the command to alloc or
free streams rings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xhci_ring structure contained information that is really related to an
endpoint, not a ring. This will cause problems later when endpoint
streams are supported and there are multiple rings per endpoint.
Move the endpoint state and cancellation information into a new virtual
endpoint structure, xhci_virt_ep. The list of TRBs to be cancelled should
be per endpoint, not per ring, for easy access. There can be only one TRB
that the endpoint stopped on after a stop endpoint command (even with
streams enabled); move the stopped TRB information into the new virtual
endpoint structure. Also move the 31 endpoint rings and temporary ring
storage from the virtual device structure (xhci_virt_device) into the
virtual endpoint structure (xhci_virt_ep).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In order for the dbgp driver to survive suspend/resume, on every ehci
resume operation the debug controller must get re-initialized.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: dbrownell@users.sourceforge.net
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the EHCI debug port is initialized and in use, the EHCI host
controller driver must follow two rules.
1) If the EHCI host driver issues a controller reset, the debug
controller driver re-initialization must get called after the reset
is completed.
2) The EHCI host driver should ignore any requests to the physical
EHCI debug port when the EHCI debug port is in use.
The code to check for the debug port was moved from ehci_pci_reinit()
to ehci_pci_setup because it must get called prior to ehci_reset()
which will clear the debug port registers.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: dbrownell@users.sourceforge.net
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1281) changes the way ehci-hcd deschedules interrupt
QHs, copying the approach used for async QHs. The caller is no longer
responsible for rescheduling the QH if its queue is non-empty; instead
the reschedule is done directly by intr_deschedule(), after calling
qh_completions(). This is exactly the same as how end_unlink_async()
works.
ehci_urb_dequeue() and intr_deschedule() now correctly handle the case
where they are called while another interrupt URB for the same QH is
being given back. This was a surprisingly large blind spot. And
scan_periodic() now respects the new needs_rescan flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1280) fixes an obscure bug in ehci-hcd's dequeuing logic
for async URBs. If a later URB is unlinked and the completion
routine unlinks an earlier URB, then the earlier URB won't be given
back in a timely manner because the endpoint queue isn't rescanned as
it should be.
Similar bugs occur if an endpoint is reset or a halt is cleared while
a completion routine is running, because the subroutines don't test
for the COMPLETING state.
All these problems are solved by adding a new needs_rescan flag to the
ehci_qh structure. If the flag is set while scanning through an idle
QH, the scan will be repeated. If the QH isn't idle then an unlink
cycle will be initiated, and the proper action will be taken when it
becomes idle.
Also, an unnecessary test is removed from qh_link_async(): That
routine is never called if the QH's state isn't IDLE.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove unused variable in ohci-ep93xx.c.
This only shows up when CONFIG_PM is enabled.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct priority problem in the use of ! and &.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ expression E; constant C; @@
- !E & C
+ !(E & C)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch was previously discussed in the following thread:
http://thread.gmane.org/gmane.linux.usb.general/19472/focus=19484
On the OMAP3 device the usbhost controller is in a separate internal
power-domain. So when the usbhost is inactive or suspend is called,
we can disable clocks and power-down the usbhost to save power.
Recently we found that after calling ehci_bus_suspend() and disabling
the usbhost clocks we would see the ehci watchdog timer event fire. This
was causing a kernel panic because the usbhost controllers clocks were
disabled and inside the watchdog timer function the clocks were not
being re-enabled, so when the ehci registers were accessed this resulted
in a CPU data-abort.
To avoid this panic, per recommendation from Alan Stern (see above thread), we
make sure any pending timer events (that may have been scheduled by calling
ehci_work within the ehci_bus_suspend() function) are deleted before returning.
Signed-off-by: Fei Yang <fei.yang@motorola.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We are seeing a number of crashes in SMM, when VT-d is enabled while
'Legacy USB support' is enabled in various BIOSes.
The BIOS is supposed to indicate which addresses it uses for DMA in a
special ACPI table ("RMRR"), so that we can punch a hole for it when we
set up the IOMMU.
The problem is, as usual, that BIOS engineers are totally incompetent.
They write code which will crash if the DMA goes AWOL, and then they
either neglect to provide an RMRR table at all, or they put the wrong
addresses in it. And of course they don't do _any_ QA, since that would
take too much time away from their crack-smoking habit.
The real fix, of course, is for consumers to refuse to buy motherboards
which only have closed-source firmware available. If we had _open_
firmware, bugs like this would be easy to fix.
Since that's something I can only dream about, this patch implements an
alternative -- ensuring that the USB controllers are handed off from the
BIOS and quiesced _before_ the IOMMU is initialised. That would have
been a much better design than this RMRR nonsense in the first place, of
course. The bootloader has no business doing DMA after the OS has booted
anyway.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
HCHWCFG_PULLDOWN_DS2 and HCHWCFG_PULLDOWN_DS1 were swapped. Incorrect
operator precedence in isp1362_hc_start() hid part of the problem.
This fixes a problem where Port 1 in Host mode fails to see disconnects.
Signed-Off-By: Ken MacLeod <ken@bitsko.slc.ut.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some ohci-pxa27x platforms may require OCPM and NOCP in UHCRHDA to be
clear, but the existing code was only allowing setting. This patch
ensures that these bits are clear if the respective flags are not set.
This is particularly important for the PXA3xx family where the
documentation says OCPM must be cleared, but it is set after reset.
Signed-off-by: Aric Blumer <aric@sdgsystems.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
At91sam9g45 series has a set of high speed USB interfaces.
The host driver is an EHCI with its companion OHCI. OHCI is
always handled by ohci-at91.c.
This wrapper is just modified to allow IRQ sharing
between two controllers.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add host USB High speed driver for at91sam9g45 series.
The host driver is an EHCI with its companion OHCI. EHCI is
handled by the new ehci-atmel.c whereas the OHCI is always
handled by ohci-at91.c.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
move both ohci-au1xxx and ehci-au1xxx over to dev_pm_ops.
Tested on Au1200.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Platform device support was merged earlier, but support for boards to
customize the devflags aspect of the controller was not. We want this on
Blackfin systems to control the bus width, but might as well expose all of
the fields while we're at it.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Intel Moorestown EHCI controller supports non-standard HOSTPCx register
extension. This register controls the LPM behaviour and controls the behaviour
of each USB port.
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Alek Du <alek.du@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ehci_qh structure merged hw and sw together which is not good:
1. More and more items are being added into ehci_qh, the ehci_qh software
part are unnecessary to be allocated in DMA qh_pool.
2. If HCD has local SRAM, the sw part will consume it too, and it won't
bring any benefit.
3. For non-cache-coherence system, the entire ehci_qh is uncachable, actually
we only need the hw part to be uncacheable. Spliting them will let the sw
part to be cacheable.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Basically the io watchdog is only useful for those quirk HCDs. For most
good ones, it only brings unnecessary wakeups. At least, I know the
Intel EHCI HCDs should turn off the flag.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb_hcd_endpoint_reset() may be called in atomic context and must not
sleep. So make whci-hcd's endpoint_reset() asynchronous. URBs
submitted while the reset is in progress will be queued (on the std
list) and transfers will resume once the reset is complete.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add ehci support for w90p910 platform.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
vfree() does it's own NULL checking,so no need for check before
calling it.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Interrupt transfers are submitted to the xHCI hardware using the same TRB
type as bulk transfers. Re-use the bulk transfer enqueueing code to
enqueue interrupt transfers.
Interrupt transfers are a bit different than bulk transfers. When the
interrupt endpoint is to be serviced, the xHC will consume (at most) one
TD. A TD (comprised of sg list entries) can take several service
intervals to transmit. The important thing for device drivers to note is
that if they use the scatter gather interface to submit interrupt
requests, they will not get data sent from two different scatter gather
lists in the same service interval.
For now, the xHCI driver will use the service interval from the endpoint's
descriptor (bInterval). Drivers will need a hook to poll at a more
frequent interval. Set urb->interval to the interval that the xHCI
hardware will use.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xHCI hardware reports the number of bytes untransferred for a given
transfer buffer. If the hardware reports a bytes untransferred value
greater than the submitted buffer size, we want to play it safe and say no
data was transferred. If the driver considers a short packet to be an
error, remember to set -EREMOTEIO.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure that the driver that submitted the URB considers a short packet
an error before setting -EREMOTEIO during a short control transfer.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure that the amount of data the xHC says was transmitted is less
than or equal to the size of the requested transfer buffer. Before, if
the host controller erroneously reported that the number of bytes
untransferred was bigger than the buffer in the URB, urb->actual_length
could be set to a very large size.
Make sure urb->actual_length <= urb->transfer_buffer_length.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On a successful transfer, urb->td is freed before the URB is ready to be
given back to the driver. Don't touch urb->td after it's freed. This bug
would have only shown up when xHCI debugging was turned on, and the freed
memory was quickly reused for something else.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 0.95 xHCI spec says that non-control endpoints will be halted if a
babble is detected on a transfer. The 0.96 xHCI spec says all types of
endpoints will be halted when a babble is detected. Some hardware that
claims to be 0.95 compliant halts the control endpoint anyway.
When a babble is detected on a control endpoint, check the hardware's
output endpoint context to see if the endpoint is marked as halted. If
the control endpoint is halted, a reset endpoint command must be issued
and the transfer ring dequeue pointer needs to be moved past the stopped
transfer. Basically, we treat it as if the control endpoint had stalled.
Handle bulk babbling endpoints as if we got a completion event with a
stall completion code.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use trb_comp_code instead of getting the completion code from the transfer
event every time.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This Fresco Logic xHCI host controller chip revision puts bad data into
the output endpoint context after a Reset Endpoint command. It needs a
Configure Endpoint command (instead of a Set TR Dequeue Pointer command)
after the reset endpoint command.
Set up the input context before issuing the Reset Endpoint command so we
don't copy bad data from the output endpoint context. The HW also can't
handle two commands queued at once, so submit the TRB for the Configure
Endpoint command in the event handler for the Reset Endpoint command.
Devices that stall on control endpoints before a configuration is selected
will not work under this Fresco Logic xHCI host controller revision.
This patch is for prototype hardware that will be given to other companies
for evaluation purposes only, and should not reach consumer hands. Fresco
Logic's next chip rev should have this bug fixed.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a control endpoint stalls, the next control transfer will clear the
stall. The USB core doesn't call down to the host controller driver's
endpoint_reset() method when control endpoints stall, so the xHCI driver
has to do all its stall handling for internal state in its interrupt handler.
When the host stalls on a control endpoint, it may stop on the data phase
or status phase of the control transfer. Like other stalled endpoints,
the xHCI driver needs to queue a Reset Endpoint command and move the
hardware's control endpoint ring dequeue pointer past the failed control
transfer (with a Set TR Dequeue Pointer or a Configure Endpoint command).
Since the USB core doesn't call usb_hcd_reset_endpoint() for control
endpoints, we need to do this in interrupt context when we get notified of
the stalled transfer. URBs may be queued to the hardware before these two
commands complete. The endpoint queue will be restarted once both
commands complete.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Full speed devices have varying max packet sizes (8, 16, 32, or 64) for
endpoint 0. The xHCI hardware needs to know the real max packet size
that the USB core discovers after it fetches the first 8 bytes of the
device descriptor.
In order to fix this without adding a new hook to host controller drivers,
the xHCI driver looks for an updated max packet size for control
endpoints. If it finds an updated size, it issues an evaluate context
command and waits for that command to finish. This should only happen in
the initialization and device descriptor fetching steps in the khubd
thread, so blocking should be fine.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Set the max packet size for the default control endpoint on high speed
devices to be 64 bytes. High speed devices always have a max packet size
of 64 bytes. There's no use setting it to eight for the initial 8 byte
descriptor fetch and then issuing (and waiting for) an evaluate context
command to update it to 64 bytes for the subsequent control transfers.
The USB core guesses that the max packet size on a full speed control
endpoint is 64 bytes, and then updates it after the first 8-byte
descriptor fetch. Change the initial setup for the xHCI internal
representation of the full speed device to have a 64 byte max packet size.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Refactor out the code issue, wait for, and parse the event completion code
for a configure endpoint command. Modify it to support the evaluate
context command, which has a very similar submission process. Add
functions to copy parts of the output context into the input context
(which will be used in the evaluate context command).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the virtual address of the memory hardware uses, not the address for
the container of that memory.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Different sections of the xHCI 0.95 specification had opposing
requirements for the chain bit in a link transaction request buffer (TRB).
The chain bit is used to designate that adjacent TRBs are all part of the
same scatter gather list that should be sent to the device. Link TRBs can
be in the middle, or at the beginning or end of these chained TRBs.
Sections 4.11.5.1 and 6.4.4.1 both stated the link TRB "shall have the
chain bit set to 1", meaning it is always chained to the next TRB.
However, section 4.6.9 on the stop endpoint command has specific cases for
what the hardware must do for a link TRB with the chain bit set to 0. The
0.96 specification errata later cleared up this issue by fixing the
4.11.5.1 and 6.4.4.1 sections to state that a link TRB can have the chain
bit set to 1 or 0.
The problem is that the xHCI cancellation code depends on the chain bit of
the link TRB being cleared when it's at the end of a TD, and some 0.95
xHCI hardware simply stops processing the ring when it encounters a link
TRB with the chain bit cleared.
Allow users who are testing 0.95 xHCI prototypes to set a module parameter
(link_quirk) to turn on this link TRB work around. Cancellation may not
work if the ring is stopped exactly on a link TRB with chain bit set, but
cancellation should be a relatively uncommon case.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SL811 Device detected after removal used to be working in linux-2.6.22
but then broke somewhere between 2.6.22 and 2.6.28. Current
hub_port_connect_change() in drivers/usb/core/hub.c won't call
usb_disconnect() in case the SL811 driver sets portstatus
USB_PORT_FEAT_CONNECTION upon removal.
AFAIK the SL811 has only a combined Device Insert/Remove
detection bit, therefore use a count to distinguish insert or remove.
Signed-Off-By: Michael Hennerich <hennerich@blackfin.uclinux.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (262 commits)
sh: mach-ecovec24: Add user debug switch support
sh: Kill off unused se_skipped in alignment trap notification code.
sh: Wire up HAVE_SYSCALL_TRACEPOINTS.
video: sh_mobile_lcdcfb: use both register sets for display panning
video: sh_mobile_lcdcfb: implement display panning
sh: Fix up sh7705 flush_dcache_page() build.
sh: kfr2r09: document the PLL/FLL <-> RF relationship.
sh: mach-ecovec24: need asm/clock.h.
sh: mach-ecovec24: deassert usb irq on boot.
sh: Add KEYSC support for EcoVec24
sh: add kycr2_delay for sh_keysc
sh: cpufreq: Include CPU id in info messages.
sh: multi-evt support for SH-X3 proto CPU.
sh: clkfwk: remove bogus set_bus_parent() from SH7709.
sh: Fix the indication point of the liquid crystal of AP-325RXA(AP3300)
sh: Add EcoVec24 romImage defconfig
sh: USB disable process is needed if romImage boot for EcoVec24
sh: EcoVec24: add HIZA setting for LED
sh: EcoVec24: write MAC address in boot
sh: Add romImage support for EcoVec24
...
Change default debugfs directory as mounting point for debugging
UHCI(Universal Host Controller Interface driver) for USB.
As we all know, We need change default directory for consistency of
debugfs by Greg K-H
Signed-off-by: GeunSik Lim <geunsik.lim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On resume, the power-related bits in UHCRHDA were not being set, so
they would default to the reset state. For PXA3xx devices, OCPM must
be cleared, but it was remaining set from resume reset.
Signed-off-by: Aric D. Blumer <aric@sdgsystems.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch (as1274) simplifies the counting of transaction-error
retries. Now we will count up from 0 to QH_XACTERR_MAX instead of
down from QH_XACTERR_MAX to 0.
The patch also fixes a small bug: qh->xacterr was not getting
initialized for interrupt endpoints.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1273) fixes two(!) bugs introduced by the new
Clear-TT-Buffer implementation in ehci-hcd.
It is now possible for an idle QH to have some URBs on its
queue -- this will happen if a Clear-TT-Buffer is pending for
the QH's endpoint. Consequently we should not issue a warning
when someone tries to unlink an URB from an idle QH; instead
we should process the request immediately.
The refcounts for QHs could get messed up, because
submit_async() would increment the refcount when calling
qh_link_async() and qh_link_async() would then refuse to link
the QH into the schedule if a Clear-TT-Buffer was pending.
Instead we should increment the refcount only when the QH
actually is added to the schedule. The current code tries to
be clever by leaving the refcount alone if an unlink is
immediately followed by a relink; the patch changes this to an
unconditional decrement and increment (although they occur in
the opposite order).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Tested-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes up the dev_pm_ops conversion and wires up the callbacks needed
for hibernation.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Correct the xHCI code to handle stalls on USB endpoints. We need to move
the endpoint ring's dequeue pointer past the stalled transfer, or the HW
will try to restart the transfer the next time the doorbell is rung.
Don't attempt to clear a halt on an endpoint if we haven't seen a stalled
transfer for it. The USB core will attempt to clear a halt on all
endpoints when it selects a new configuration.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support for controllers that use 64-byte contexts. The following context
data structures are affected by this: Device, Input, Input Control, Endpoint,
and Slot. To accommodate the use of either 32 or 64-byte contexts, a Device or
Input context can only be accessed through functions which look-up and return
pointers to their contained contexts.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure the xHCI output device context is 64-byte aligned. Previous
code was using the same structure for both the output device context and
the input control context. Since the structure had 32 bytes of flags
before the device context, the output device context wouldn't be 64-byte
aligned. Define a new structure to use for the output device context and
clean up the debugging for these two structures.
The copy of the device context in the input control context does *not*
need to be 64-byte aligned.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allocates and initializes the scratchpad buffer array (XHCI 4.20). This is an
array of 64-bit DMA addresses to scratch pages that the controller may use
during operation. The number of pages is specified in the "Max Scratchpad
Buffers" field of HCSPARAMS2. The DMA address of this array is written into
slot 0 of the DCBAA.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a work around for a bug in the SuperSpeed Endpoint Companion Descriptor
parsing code. It fails in some corner cases, which means ep->ss_ep_comp may be
NULL.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pass back a babble error when this error code is seen in the transfer event TRB.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xHCI host controller can be programmed to retry a transfer a certain number
of times per endpoint before it passes back an error condition to the host
controller driver. The xHC will return an error code when the error count
transitions from 1 to 0. Programming an error count of 3 means the xHC tries
the transfer 3 times, programming it with a 1 means it tries to transfer once,
and programming it with 0 means the HW tries the transfer infinitely.
We want isochronous transfers to only be tried once, so set the error count to
one.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add more debugging to the irq handler, slot context initialization, ring
operations, URB cancellation, and MMIO writes.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Event Handler Busy bit in the event ring dequeue pointer is write 1 to
clear. Fix the interrupt service routine to clear that bit after the
event handler has run.
xhci_set_hc_event_deq() is designed to update the event ring dequeue pointer
without changing any of the four reserved bits in the lower nibble. The event
handler busy (EHB) bit is write one to clear, so the new value must always
contain a zero in that bit in order to preserve the EHB value.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When there is a short packet on a control transfer, the xHCI host controller
hardware will generate two events. The first event will be for the data stage
TD with a completion code for a short packet. The second event will be for the
status stage with a successful completion code. Before this patch, the xHCI
driver would giveback the short control URB when it received the event for the
data stage TD. Then it would become confused when it saw a status stage event
for the endpoint for an URB it had already finished processing.
Change the xHCI host controller driver to wait for the status stage event when
it receives a short transfer completion code for a data stage TD.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are several xHCI data structures that use two 32-bit fields to
represent a 64-bit address. Since some architectures don't support 64-bit
PCI writes, the fields need to be written in two 32-bit writes. The xHCI
specification says that if a platform is incapable of generating 64-bit
writes, software must write the low 32-bits first, then the high 32-bits.
Hardware that supports 64-bit addressing will wait for the high 32-bit
write before reading the revised value, and hardware that only supports
32-bit writes will ignore the high 32-bit write.
Previous xHCI code represented 64-bit addresses with two u32 values. This
lead to buggy code that would write the 32-bits in the wrong order, or
forget to write the upper 32-bits. Change the two u32s to one u64 and
create a function call to write all 64-bit addresses in the proper order.
This new function could be modified in the future if all platforms support
64-bit writes.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xHCI functions to queue an URB onto the hardware rings must be called
with the xhci spinlock held. Those functions will allocate memory, and
take a gfp_t memory flags argument. We must pass them the GFP_ATOMIC
flag, since we don't want the memory allocation to attempt to sleep while
waiting for more memory to become available.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When an endpoint on a device under an xHCI host controller stalls, the
host controller driver must let the hardware know that the USB core has
successfully cleared the halt condition. The HCD submits a Reset Endpoint
Command, which will clear the toggle bit for USB 2.0 devices, and set the
sequence number to zero for USB 3.0 devices.
The xHCI urb_enqueue will accept new URBs while the endpoint is halted,
and will queue them to the hardware rings. However, the endpoint doorbell
will not be rung until the Reset Endpoint Command completes.
Don't queue a reset endpoint command for root hubs. khubd clears halt
conditions on the roothub during the initialization process, but the roothub
isn't a real device, so the xHCI host controller doesn't need to know about the
cleared halt.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 0.95 xHCI specification requires software to set the "TD size" field
in each transaction request block (TRB). This field gives the host
controller an indication of how much data is remaining in the TD
(including the buffer in the current TRB). Set this field in bulk TRBs
and data stage TRBs for control transfers.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without this change the loops won't start
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I noticed that USB initialization didn't setup correctly on my kirkwood
based board (OpenRD base) if I hadn't initialized USB in U-boot first.
The error message looks like this:
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: can't setup
orion-ehci orion-ehci.0: USB bus 1 deregistered
orion-ehci orion-ehci.0: init orion-ehci.0 fail, -110
orion-ehci: probe of orion-ehci.0 failed with error -110
which is caused by ehci_halt() timing out in the handshake() call. I
noticed that U-boot does a reset before calling handshake(), so this
patch does the same thing for Linux. USB now works for me.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
OMAP: OHCI: hc_driver's stop method should call ohci_stop
Without this, the ohci-omap driver will not cleanup the debugfs
nodes when the driver is unloaded. So the next insmod will fail,
if CONFIG_DEBUG_FS and CONFIG_USB_DEBUG are both selected.
Reported-by: vikram pandita <vikram.pandita@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move r8a66597 hardware register definitions from the host
controller header file to the platform data header file.
With this change in place we can easily share register
definitions between the host controller driver and a future
gadget driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the r8a66597-hcd driver to use the on_chip flag
from platform data to enable on chip behaviour instead
of relying on CONFIG_SUPERH_ON_CHIP_R8A66597 ugliness.
This makes the code cleaner and also allows us to support
both external and internal r8a66597 with the same kernel.
It also makes the Kconfig part more future proof since
we with this patch can add support for new processors
with on-chip r8a66597 without modifying the Kconfig.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the r8a66597-hcd driver to dev_pm_ops. This makes
the driver a good PM citizen and removes a warning printout.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch (as1259b) makes ehci-hcd return the total number of bytes
transferred in urb->actual_length for Isochronous transfers.
Until now, the actual_length value was unaccountably left at 0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1257) revises the way ehci-hcd detects STALLs. The
logic is a little peculiar because there's no hardware status bit
specifically meant to indicate a STALL. You just have to guess that a
STALL was received if the BABBLE bit (which is fatal) isn't set and
the transfer stopped before all its retries were used up.
The existing code doesn't do this properly, because it tests for MMF
(Missed MicroFrame) and DBE (Data Buffer Error) before testing the
retry counter. Thus, if a transaction gets either MMF or DBE the
corresponding flag is set and the transaction is retried. If the
second attempt receives a STALL then -EPIPE is the correct return
value. But the existing code would see the MMF or DBE flag instead
and return -EPROTO, -ENOSR, or -ECOMM.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1256) changes ehci-hcd and all the other drivers in the
EHCI family to make use of the new clear_tt_buffer callbacks. When a
Clear-TT-Buffer request is in progress for a QH, the QH is not allowed
to be linked into the async schedule until the request is finished.
At that time, if there are any URBs queued for the QH, it is linked
into the async schedule.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1255) updates the interface for calling
usb_hub_clear_tt_buffer(). Even the name of the function is changed!
When an async URB (i.e., Control or Bulk) going through a high-speed
hub to a non-high-speed device is cancelled or fails, the hub's
Transaction Translator buffer may be left busy still trying to
complete the transaction. The buffer has to be cleared; that's what
usb_hub_clear_tt_buffer() does.
It isn't safe to send any more URBs to the same endpoint until the TT
buffer is fully clear. Therefore the HCD needs to be told when the
Clear-TT-Buffer request has finished. This patch adds a callback
method to struct hc_driver for that purpose, and makes the hub driver
invoke the callback at the proper time.
The patch also changes a couple of names; "hub_tt_kevent" and
"tt.kevent" now look rather antiquated.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We could just make the USB_OHCI_HCD_PPC_OF option implicit
and selected only if at least one of USB_OHCI_HCD_PPC_OF_BE
and USB_OHCI_HCD_PPC_OF_LE are set.
[ dbrownell@users.sourceforge.net: fix patch manglation and dependencies ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The isp1760_plat_remove function is declared with __devexit, so the
.remove assignment needs to be wrapped with __devexit_p().
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is an update to the "usb-ehci-update-toggle-state-for-linked-qhs"
patch. Since an HCD's endpoint_reset method can be called in
interrupt context, it mustn't assume that interrupts are enabled or
that it can sleep.
So we revert to the original way of refreshing QHs' toggle bits. Now
the endpoint_reset method merely clears the toggle flag in the device
structure (as was done before) and starts an async QH unlink. When the
QH is linked again, after the unlink finishes and an URB is queued,
the qh_refresh() routine will update the QH's toggle bit.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: David <david@unsolicited.net>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
FHCI_PORT_DISABLED, -LOW and -FULL are mutually exclusive as status.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sh7724 processor has two on-chip r8a66597 blocks, so add
it to the list of processors for SUPERH_ON_CHIP_R8A66597.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
While it looks like xhci was written with both PCI and non-PCI in mind,
apparently only the former has seen any testing. xhci-mem.o can be "fixed"
with a linux/dmapool.h include, but there are still parts of the code that
make use of struct pci_dev directly. So, at least more work is needed before
this can be turned on for non-PCI builds:
CC drivers/usb/host/xhci-mem.o
drivers/usb/host/xhci-mem.c: In function 'xhci_segment_alloc':
drivers/usb/host/xhci-mem.c:45: error: implicit declaration of function 'dma_pool_alloc'
drivers/usb/host/xhci-mem.c:45: warning: assignment makes pointer from integer without a cast
drivers/usb/host/xhci-mem.c: In function 'xhci_segment_free':
drivers/usb/host/xhci-mem.c:67: error: implicit declaration of function 'dma_pool_free'
drivers/usb/host/xhci-mem.c: In function 'xhci_alloc_virt_device':
drivers/usb/host/xhci-mem.c:239: warning: assignment makes pointer from integer without a cast
drivers/usb/host/xhci-mem.c:248: warning: assignment makes pointer from integer without a cast
drivers/usb/host/xhci-mem.c: In function 'xhci_mem_cleanup':
drivers/usb/host/xhci-mem.c:578: error: implicit declaration of function 'dma_pool_destroy'
drivers/usb/host/xhci-mem.c: In function 'xhci_mem_init':
drivers/usb/host/xhci-mem.c:657: error: implicit declaration of function 'dma_pool_create'
drivers/usb/host/xhci-mem.c:658: warning: assignment makes pointer from integer without a cast
drivers/usb/host/xhci-mem.c:663: warning: assignment makes pointer from integer without a cast
make[3]: *** [drivers/usb/host/xhci-mem.o] Error 1
CC drivers/usb/host/xhci-pci.o
drivers/usb/host/xhci-pci.c: In function 'xhci_pci_reinit':
drivers/usb/host/xhci-pci.c:39: error: implicit declaration of function 'pci_set_mwi'
drivers/usb/host/xhci-pci.c: At top level:
drivers/usb/host/xhci-pci.c:151: error: 'usb_hcd_pci_probe' undeclared here (not in a function)
drivers/usb/host/xhci-pci.c:152: error: 'usb_hcd_pci_remove' undeclared here (not in a function)
drivers/usb/host/xhci-pci.c:155: error: 'usb_hcd_pci_shutdown' undeclared here (not in a function)
drivers/usb/host/xhci-pci.c:159: warning: function declaration isn't a prototype
drivers/usb/host/xhci-pci.c:164: warning: function declaration isn't a prototype
make[3]: *** [drivers/usb/host/xhci-pci.o] Error 1
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add Makefile and Kconfig entries for the xHCI host controller driver.
List Sarah Sharp as the maintainer for the xHCI driver.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Narrow down time spent holding the xHCI spinlock so that it's only used to
protect the xHCI rings, not as mutual exclusion. Stop allocating memory
while holding the spinlock and calling xhci_alloc_virt_device() and
xhci_endpoint_init().
The USB core should have locking in it to prevent device state to be
manipulated by more than one kernel thread. E.g. you can't free a device
while you're in the middle of setting a new configuration. So removing
the locks from the sections where xhci_alloc_dev() and
xhci_reset_bandwidth() touch xHCI's representation of the device should be
OK.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mask off the lower 16 bits of the interrupt control register, instead of
masking off the upper 16 bits. The interrupt moderation interval field is
the lower 16 bytes, and is set to 0x4000 (1ms) by default. The previous
code was adding 40 us to the default value, instead of setting it to 40
us. This makes performance really bad.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The packed attribute allows gcc to muck with the alignment of data
structures, which may lead to byte-wise writes that break atomicity of
writes. Packed should only be used when the compile may add undesired
padding to the structure. Each element of the structure will be aligned
by C based on its size and the size of the elements around it. E.g. a u64
would be aligned on an 8 byte boundary, the next u32 would be aligned on a
four byte boundary, etc.
Since most of the xHCI structures contain only u32 bit values, removing
the packed attribute for them should be harmless. (A future patch will
change some of the twin 32-bit address fields to one 64-bit field, but all
those places have an even number of 32-bit fields before them, so the
alignment should be correct.) Add BUILD_BUG_ON statements to check that
the compiler doesn't add padding to the data structures that have a
hardware-defined layout.
While we're modifying the registers, change the name of intr_reg to
xhci_intr_reg to avoid global conflicts.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg KH introduced a bug into xhci_trb_virt_to_dma() when he changed the
type of offset to dma_addr_t from unsigned int and dropped the casts to
unsigned int around the virtual address pointer subtraction.
trb and seg->trbs are both valid pointers to virtual addresses, so the
compiler will mod the subtraction by the size of union trb (16 bytes).
segment_offset is an unsigned long, which is guaranteed to be at least as
big as a void *.
Drop the void * casts in the first if statement because trb and seg->trbs
are both pointers of the same type (pointers to union trb).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xhci-mem.c includes calls to dma_pool_alloc() and other functions defined
in linux/dmapool.h. Make sure to include that header file.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure the error path in xhci_urb_enqueue() releases the spinlock
before it returns. Reported by Oliver in
http://marc.info/?l=linux-usb&m=124091637311832&w=2
Reported-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Differentiate between SuperSpeed endpoint companion descriptor and the
wireless USB endpoint companion descriptor. Make all structure names for
this descriptor have "ss" (SuperSpeed) in them. David Vrabel asked for
this change in http://marc.info/?l=linux-usb&m=124091465109367&w=2
Reported-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Force the compiler to write the cycle bit of the Link TRB last. This
ensures that the hardware doesn't think it owns the Link TRB before we set
the chain bit. Reported by Oliver in this thread:
http://marc.info/?l=linux-usb&m=124091532410219&w=2
Reported-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop spinlock in xhci_irq() error path.
This fixes the issue reported by Oliver Neukum on this thread:
http://marc.info/?l=linux-usb&m=124090924401444&w=2
Remove unnecessary register read reported by Viral Mehta:
http://marc.info/?l=linux-usb&m=124091326007398&w=2
Reported-by: Oliver Neukum <oliver@neukum.org>
Reported-by: Viral Mehta <viral.mehta@einfochips.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make all globally visible functions start with xhci_ and mark functions as
static if they're only called within the same C file. Fix some long lines
while we're at it.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure to preserve all bits *except* the TRB_CHAIN bit when giving a
Link TRB to the hardware. We need to save things like TRB type and the
toggle bit in the control dword.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 0.95 xHCI spec says that if the xHCI HW support 64-bit addressing, you
must write the whole 64-bit address as one atomic operation, or write the
low 32 bits, and then the high 32 bits. I had the register writes
swapped in some places.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the warning:
drivers/usb/host/xhci.h:1083: warning: passing argument 1 of ‘xhci_to_hcd’ discards qualifiers from pointer target type
drivers/usb/host/xhci.h:1083: warning: passing argument 1 of ‘xhci_to_hcd’ discards qualifiers from pointer target type
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Turns out someone never built this code on a 64bit platform.
Someone owes me a beer...
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The former is way to generic for a global symbol.
Fixes this build error:
drivers/usb/built-in.o: In function `.handle_event': (.text+0x67dd0): multiple definition of `.handle_event'
drivers/pcmcia/built-in.o:(.text+0xcfcc): first defined here
drivers/usb/built-in.o: In function `handle_event': (.opd+0x5bc8): multiple definition of `handle_event'
drivers/pcmcia/built-in.o:(.opd+0xed0): first defined here
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add URB cancellation support to the xHCI host controller driver. This
currently supports cancellation for endpoints that do not have streams
enabled.
An URB is represented by a number of Transaction Request Buffers (TRBs),
that are chained together to make one (or more) Transaction Descriptors
(TDs) on an endpoint ring. The ring is comprised of contiguous segments,
linked together with Link TRBs (which may or may not be chained into a TD).
To cancel an URB, we must stop the endpoint ring, make the hardware skip
over the TDs in the URB (either by turning them into No-op TDs, or by
moving the hardware's ring dequeue pointer past the last TRB in the last
TD), and then restart the ring.
There are times when we must drop the xHCI lock during this process, like
when we need to complete cancelled URBs. We must ensure that additional
URBs can be marked as cancelled, and that new URBs can be enqueued (since
the URB completion handlers can do either). The new endpoint ring
variables cancels_pending and state (which can only be modified while
holding the xHCI lock) ensure that future cancellation and enqueueing do
not interrupt any pending cancellation code.
To facilitate cancellation, we must keep track of the starting ring
segment, first TRB, and last TRB for each URB. We also need to keep track
of the list of TDs that have been marked as cancelled, separate from the
list of TDs that are queued for this endpoint. The new variables and
cancellation list are stored in the xhci_td structure.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for bulk URBs that pass scatter gather lists to xHCI. This allows
xHCI to more efficiently enqueue these transfers, and allows the host
controller to take advantage of USB 3.0 "bursts" for bulk endpoints.
Use requested length to calculate the number of TRBs needed for a scatter gather
list transfer, instead of using the number of sglist entries. The application
can pass down a scatter gather list that is bigger than it needs for the
requested transfer.
Scatter gather entries can cross 64KB boundaries, so be careful to setup TRBs
such that no buffer crosses a 64KB boundary.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow device drivers to submit URBs to bulk endpoints on devices under an
xHCI host controller. Share code between the control and bulk enqueueing
functions when it makes sense.
To get the best performance out of bulk transfers, SuperSpeed devices must
have the bMaxBurst size copied from their endpoint companion controller
into the xHCI device context. This allows the host controller to "burst"
up to 16 packets before it has to wait for the device to acknowledge the
first packet.
The buffers in Transfer Request Blocks (TRBs) can cross page boundaries,
but they cannot cross 64KB boundaries. The buffer must be broken into
multiple TRBs if a 64KB boundary is crossed.
The sum of buffer lengths in all the TRBs in a Transfer Descriptor (TD)
cannot exceed 64MB. To work around this, the enqueueing code must enqueue
multiple TDs. The transfer event handler may incorrectly give back the
URB in this case, if it gets a transfer event that points somewhere in the
first TD. FIXME later.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the xHCI host controller hardware (xHC) has an internal schedule, it
needs a better representation of what devices are consuming bandwidth on
the bus. Each device is represented by a device context, with data about
the device, endpoints, and pointers to each endpoint ring.
We need to update the endpoint information for a device context before a
new configuration or alternate interface setting is selected. We setup an
input device context with modified endpoint information and newly
allocated endpoint rings, and then submit a Configure Endpoint Command to
the hardware.
The host controller can reject the new configuration if it exceeds the bus
bandwidth, or the host controller doesn't have enough internal resources
for the configuration. If the command fails, we still have the older
device context with the previous configuration. If the command succeeds,
we free the old endpoint rings.
The root hub isn't a real device, so always say yes to any bandwidth
changes for it.
The USB core will enable, disable, and then enable endpoint 0 several
times during the initialization sequence. The device will always have an
endpoint ring for endpoint 0 and bandwidth allocated for that, unless the
device is disconnected or gets a SetAddress 0 request. So we don't pay
attention for when xhci_check_bandwidth() is called for a re-add of
endpoint 0.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow device drivers to enqueue URBs to control endpoints on devices under
an xHCI host controller. Each control transfer is represented by a
series of Transfer Descriptors (TDs) written to an endpoint ring. There
is one TD for the Setup phase, (optionally) one TD for the Data phase, and
one TD for the Status phase.
Enqueue these TDs onto the endpoint ring that represents the control
endpoint. The host controller hardware will return an event on the event
ring that points to the (DMA) address of one of the TDs on the endpoint
ring. If the transfer was successful, the transfer event TRB will have a
completion code of success, and it will point to the Status phase TD.
Anything else is considered an error.
This should work for control endpoints besides the default endpoint, but
that hasn't been tested.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xHCI needs to get a "Slot ID" from the host controller and allocate other
data structures for every USB device. Make usb_alloc_dev() and
usb_release_dev() allocate and free these device structures. After
setting up the xHC device structures, usb_alloc_dev() must wait for the
hardware to respond to an Enable Slot command. usb_alloc_dev() fires off
a Disable Slot command and does not wait for it to complete.
When the USB core wants to choose an address for the device, the xHCI
driver must issue a Set Address command and wait for an event for that
command.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add functionality for getting port status and hub descriptor for xHCI root
hubs. This is WIP because the USB 3.0 hub descriptor is different from
the USB 2.0 hub descriptor. For now, we lie about the root hub descriptor
because the changes won't effect how the core talks to the root hub.
Later we will need to add the USB 3.0 hub descriptor for real hubs, and
this code might change.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xHCI host controllers can optionally implement a no-op test. This
simple test ensures the OS has correctly setup all basic data structures
and can correctly respond to interrupts from the host controller
hardware.
There are two rings exercised by the no-op test: the command ring, and
the event ring.
The host controller driver writes a no-op command TRB to the command
ring, and rings the doorbell for the command ring (the first entry in
the doorbell array). The hardware receives this event, places a command
completion event on the event ring, and fires an interrupt.
The host controller driver sees the interrupt, and checks the event ring
for TRBs it can process, and sees the command completion event. (See
the rules in xhci-ring.c for who "owns" a TRB. This is a simplified set
of rules, and may not contain all the details that are in the xHCI 0.95
spec.)
A timer fires every 60 seconds to debug the state of the hardware and
command and event rings. This timer only runs if
CONFIG_USB_XHCI_HCD_DEBUGGING is 'y'.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead of keeping a "frame list" like older host controllers, the xHCI
host controller keeps internal representations of the USB devices, with a
transfer ring per endpoint. The host controller queues Transfer Request
Blocks (TRBs) to the endpoint ring, and then "rings the doorbell" for that
device. The host controller processes the transfer, places a transfer
completion event on the event ring, and interrupts the system.
The device context base address array must be allocated by the xHCI host
controller driver, along with the device contexts it points to.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allocate basic xHCI host controller data structures. For every xHC, there
is a command ring, an event ring, and a doorbell array.
The doorbell array is used to notify the host controller that work has
been enqueued onto one of the rings. The host controller driver enqueues
commands on the command ring. The HW enqueues command completion events
on the event ring and interrupts the system (currently using PCI
interrupts, although the xHCI HW will use MSI interrupts eventually).
All rings and the doorbell array must be allocated by the xHCI host
controller driver.
Each ring is comprised of one or more segments, which consists of 16-byte
Transfer Request Blocks (TRBs) that can be chained to form a Transfer
Descriptor (TD) that represents a multiple-buffer request. Segments are
linked into a ring using Link TRBs, which means they are dynamically
growable.
The producer of the ring enqueues a TD by writing one or more TRBs in the
ring and toggling the TRB cycle bit for each TRB. The consumer knows it
can process the TRB when the cycle bit matches its internal consumer cycle
state for the ring. The consumer cycle state is toggled an odd amount of
times in the ring.
An example ring (a ring must have a minimum of 16 TRBs on it, but that's
too big to draw in ASCII art):
chain cycle
bit bit
------------------------
| TD A TRB 1 | 1 | 1 |<------------- <-- consumer dequeue ptr
------------------------ | consumer cycle state = 1
| TD A TRB 2 | 1 | 1 | |
------------------------ |
| TD A TRB 3 | 0 | 1 | segment 1 |
------------------------ |
| TD B TRB 1 | 1 | 1 | |
------------------------ |
| TD B TRB 2 | 0 | 1 | |
------------------------ |
| Link TRB | 0 | 1 |----- |
------------------------ | |
| |
chain cycle | |
bit bit | |
------------------------ | |
| TD C TRB 1 | 0 | 1 |<---- |
------------------------ |
| TD D TRB 1 | 1 | 1 | |
------------------------ |
| TD D TRB 2 | 1 | 1 | segment 2 |
------------------------ |
| TD D TRB 3 | 1 | 1 | |
------------------------ |
| TD D TRB 4 | 1 | 1 | |
------------------------ |
| Link TRB | 1 | 1 |----- |
------------------------ | |
| |
chain cycle | |
bit bit | |
------------------------ | |
| TD D TRB 5 | 1 | 1 |<---- |
------------------------ |
| TD D TRB 6 | 0 | 1 | |
------------------------ |
| TD E TRB 1 | 0 | 1 | segment 3 |
------------------------ |
| | 0 | 0 | | <-- producer enqueue ptr
------------------------ |
| | 0 | 0 | |
------------------------ |
| Link TRB | 0 | 0 |---------------
------------------------
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add PCI initialization code to take control of the xHCI host controller
away from the BIOS, halt, and reset the host controller. The xHCI spec
says that BIOSes must give up the host controller within 5 seconds.
Add some host controller glue functions to handle hardware initialization
and memory allocation for the host controller. The current xHCI
prototypes use PCI interrupts, but the xHCI spec requires MSI-X
interrupts. Add code to support MSI-X interrupts, but use the PCI
interrupts for now.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the first of many patches to add support for USB 3.0 devices and
the hardware that implements the eXtensible Host Controller Interface
(xHCI) 0.95 specification. This specification is not yet publicly
available, but companies can receive a copy by becoming an xHCI
Contributor (see http://www.intel.com/technology/usb/xhcispec.htm).
No xHCI hardware has made it onto the market yet, but these patches have
been tested under the Fresco Logic host controller prototype.
This patch adds the xHCI register sets, which are grouped into five sets:
- Generic PCI registers
- Host controller "capabilities" registers (cap_regs) short
- Host controller "operational" registers (op_regs)
- Host controller "runtime" registers (run_regs)
- Host controller "doorbell" registers
These some of these registers may be virtualized if the Linux driver is
running under a VM. Virtualization has not been tested for this patch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1245) fixes a bug in ehci-hcd. When an URB is queued
for an endpoint whose QH is already in the LINKED state, the QH
doesn't get refreshed. As a result, if usb_clear_halt() was called
during the time that the QH was linked but idle, the data toggle value
in the QH doesn't get reset.
The symptom is that after a clear_halt, data gets lost and transfers
time out. This problem is starting to show up now because the
"ehci-hcd unlink speedups" patch causes QHs with no queued URBs to
remain linked for a suitable time.
The patch utilizes the new endpoint_reset mechanism to fix the
problem. When an endpoint is reset, the new method forcibly unlinks
the QH (if necessary) and safely updates the toggle value. This
allows qh_update() to be simplified and avoids using usb_device's
toggle bits in a rather unintuitive way.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Tested-by: David <david@unsolicited.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CPU/board specific parameters (PLL clock, vif etc...) can be set
by platform_data instead of module_param.
v2: remove irq_sense member in platform_data because it can OR in
IRQF_TRIGGER_LOW or IRQF_TRIGGER_FALLING against IORESOURCE_IRQ in
the struct resource.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Reviewed-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1243) tries to improve ehci-hcd's scheduling of
interrupt transfers. Instead of trying to cram all transfers with the
same period into the same frame, the new code will spread the
transfers out among lots of different frames. This should reduce the
periodic schedule load in any one frame -- some host controllers have
trouble when there's too much work to do.
A more thorough approach would stagger the uframe values as well. But
this is enough to make a big improvement.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dwayne Fontenot <dwayne.fontenot@att.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CC drivers/usb/host/hwa-hc.o
drivers/usb/host/hwa-hc.c:601: warning: initialization from incompatible pointer type
drivers/usb/host/hwa-hc.c:602: warning: initialization from incompatible pointer type
The prototype for these changed, so the message itself was dropped. As the only
thing these hooks were doing was printing out the message for debugging, there
is not much point in keeping them around. So, just kill them off.
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1237) changes the way the PCI host controller drivers
avoid retaining bogus hardware states during resume-from-hibernation.
Previously we had reset the hardware as part of preparing to reinstate
the memory image. But we can do better now with the new PM framework,
since we know exactly which resume operations are from hibernation.
The pci_resume method is changed to accept a flag indicating whether
the system is resuming from hibernation. When this flag is set, the
drivers will reset the hardware to get rid of any existing state.
Similarly, the pci_suspend method is changed to remove the
pm_message_t argument. It's no longer needed, since no special action
has to be taken when preparing to reinstate the memory image.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1236) converts the USB PCI power management routines
over to the new PM framework.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The controller device is where we want this sysfs file, especially as
the dev pointer is about to go away...
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Right now we jump through some hoops to get to the struct ohci_hcd
struct in the ohci debugfs files. Remove all of the fun casting around
and just use the pointer directly.
This is needed as the dev pointer in the hcd structure is going away,
and it makes the code simpler and smaller
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix sparse warnings in drivers/usb/host/ohci-hcd.c.
Four of the following sparse warning are seen when building on
ARM due do the macro raw_local_irq_save():
warning: symbol 'temp' shadows an earlier one
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
use usb_endpoint_type() instead of fiddling manually with bmAttributes
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A pointer to ehci_orion_drv_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Ronen Shitrit <rshitrit@marvell.com>
Cc: Lennert Buytenhek <buytenh@marvell.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Nicolas Pitre <nico@marvell.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Tzachi Perelstein <tzachi@marvell.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A pointer to r8a66597_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Cc: Magnus Damm <damm@igel.co.jp>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexey Dobriyan
Sarah Sharp
Julia Lawall
David Vrabel
Dan Carpenter
Roel Kluin
Alan Stern
Daniel Mack
Felipe Balbi
Hong Xu
Jean Delvare
Julie Zhu
Jason Wessel
Linus Torvalds
Jiri Kosina
André Goddard Rosa
Ozan Çağlayan
Oliver Neukum
Dominik Brodowski
Tony Lindgren
Libin Yang
Yoshihiro Shimoda
Mike Frysinger
Russell King
H Hartley Sweeten
Jon Hunter
David Woodhouse
Ken MacLeod
Aric Blumer
Anand Gadiyar
Nicolas Ferre
Bob Liu
Lothar Wassmann
Manuel Lauss
Michael Hennerich
Alek Du
Wan ZongShun
Figo.zhang
Uwe Kleine-Koenig
GeunSik Lim
Mike Rapoport
Paul Mundt
John Youn
Simon Kagstrom
Magnus Damm
Arnd Bergmann
Benjamin Herrenschmidt
Greg Kroah-Hartman
Stephen Rothwell
Matthias Kaehlcke