Commit Graph

62 Commits

Author SHA1 Message Date
Johannes Berg 98f0334263 cfg80211: clean up beacon loss CQM event
Having it as a sub-event for RSSI thresholds is very ugly,
but luckily no userspace actually uses the events yet.

Move the event to its own function call internally and to
its own event attribute in nl80211.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-11-26 20:56:42 +01:00
Johannes Berg f815e2b3c0 mac80211: notify drivers on sta rate table changes
This allows drivers with a firmware or chip-based rate lookup table to
use the most recent default rate selection without having to get it from
per-packet data or explicit ieee80211_get_tx_rate calls

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-11-19 19:15:50 +01:00
Johannes Berg a344d6778a mac80211: allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDR
Allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDR with software
based scanning and generate a random MAC address for them for every
scan request with the flag.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-11-19 18:46:09 +01:00
Arik Nemtsov 8a4d32f30d mac80211: add TDLS channel-switch Rx flow
When receiving a TDLS channel switch request or response, parse the frame
and call a new tdls_recv_channel_switch op in the low level driver with
the parsed data.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-11-19 18:45:26 +01:00
Arik Nemtsov a7a6bdd067 mac80211: introduce TDLS channel switch ops
Implement the cfg80211 TDLS channel switch ops and introduce new mac80211
ones for low-level drivers.
Verify low-level driver support for the new ops when using the relevant
wiphy feature bit. Also verify the peer supports channel switching before
passing the command down.

Add a new STA flag to track the off-channel state with the TDLS peer and
make sure to cancel the channel-switch if the peer STA is unexpectedly
removed.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-11-19 18:45:21 +01:00
Luciano Coelho 127f10ec60 mac80211: add device_timestamp to the drv_pre_channel_switch trace
The device_timestamp value was left out of the event trace for
drv_pre_channel_switch by mistake.  Add it.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-11-10 10:18:04 +01:00
Eliad Peller cf2c92d840 mac80211: replace restart_complete() with reconfig_complete()
Drivers might want to know also when mac80211 has
completed reconfiguring after resume (e.g. in order
to know when frames can be passed to mac80211).

Rename restart_complete() to a more-generic reconfig_complete(),
and add a new enum to indicate the reconfiguration type.

Update the current users with the new prototype.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-11-04 13:49:00 +01:00
Felix Fietkau 5b3dc42b1b mac80211: add support for driver tx power reporting
The configured tx power is often limited by hardware capabilities,
channel settings, antenna configuration, etc.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[fix tracing compilation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-11-04 10:15:09 +01:00
Luciano Coelho 0f791eb47f mac80211: allow channel switch with multiple channel contexts
Channel switch with multiple channel contexts should now work fine.
Remove check that disallows switches when multiple contexts are in
use.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-10-09 11:30:09 +02:00
Luciano Coelho f1d65583bc mac80211: add post_channel_switch driver operation
As a counterpart to the pre_channel_switch operation, add a
post_channel_switch operation.  This allows the drivers to go back to
a normal configuration after the channel switch is completed.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-10-09 11:30:09 +02:00
Luciano Coelho 6d027bcc8a mac80211: add pre_channel_switch driver operation
Some drivers may need to prepare for a channel switch also when it is
initiated from the remote side (eg. station, P2P client).  To make
this possible, add a generic callback that can be called for all
interface types.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-10-09 11:30:08 +02:00
Luciano Coelho 2ba45384e5 mac80211: add device_timestamp to the ieee80211_channel_switch struct
Some devices may need the device timestamp in order to synchronize the
channel switch.  To pass this value back to the driver, add it to the
channel switch structure and copy the device_timestamp value received
in the rx info structure into it.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-10-09 11:30:08 +02:00
Lorenzo Bianconi a4bcaf5556 mac80211: extend set_coverage_class signature
Extend mac80211 set_coverage_class API in order to enable ACK timeout
estimation algorithm (dynack) passing coverage class equals to -1
to lower drivers. Synchronize set_coverage_class routine signature with
mac80211 function pointer for p54, ath9k, ath9k_htc and ath5k drivers.

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-09-05 13:54:07 +02:00
Arik Nemtsov ee10f2c779 mac80211: protect TDLS discovery session
After sending a TDLS discovery-request, we expect a reply to arrive on
the AP's channel. We must stay on the channel (no PSM, scan, etc.), since
a TDLS setup-response is a direct packet not buffered by the AP.
Add a new mac80211 driver callback to allow discovery session protection.

Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-06-23 14:28:19 +02:00
John W. Linville 737be10d8c Merge git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next 2014-05-29 12:55:38 -04:00
Luciano Coelho 1a5f0c13d1 mac80211: add a single-transaction driver op to switch contexts
In some cases, when the driver is already using all the channel
contexts it can handle at once, we have to do an in-place switch
(ie. we cannot afford using an extra context temporarily for the
transaction).  But some drivers may not support switching the channel
context assigned to a vif on the fly (ie. without unassigning and
assigning it) while others may only work if the context is changed on
the fly, without unassigning it first.

To allow these different scenarios, add a new driver operation that
let's the driver decide how to handle an in-place switch.

Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-05-26 11:04:41 +02:00
John W. Linville 40a10fd740 Merge git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next 2014-05-22 13:58:36 -04:00
Antonio Quartulli cca674d47e mac80211: export the expected throughput
Add get_expected_throughput() API to mac80211 so that each
driver can implement its own version based on the RC
algorithm they are using (might be using an HW RC algo).
The API returns a value expressed in Kbps.

Also, add the new get_expected_throughput() member
to the rate_control_ops structure in order to be
able to query the RC algorithm (this patch provides an
implementation of this API for both minstrel and
minstrel_ht).

The related member in the station_info object is now
filled accordingly when dumping a station.

Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-05-21 09:15:16 +02:00
Eliad Peller f9ac71bfcc mac80211: fix vif name tracing
If sdata doesn't have a valid dev (e.g. in case of monitor
vif), the vif_name field was initialized with (a length of)
some short string, but later was set to a different,
potentially larger one.

This resulted in out-of-bounds write, which usually
appeared as garbage in the trace log.

Simply trace sdata->name, as it should always have the
correct name for both cases.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-05-09 14:35:40 +02:00
Johannes Berg 1b000789a4 mac80211: add tracing for ieee80211_sta_set_buffered
This is useful for debugging issues with drivers using this
function (erroneously), so add tracing for the API call.

Change-Id: Ice9d7eabb8fecbac188f0a741920d3488de700ec
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-01-06 12:09:01 +01:00
Weilong Chen f359d3fe83 mac80211: fix checkpatch errors
Fix a number of different checkpatch errors.

Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-18 10:33:06 +01:00
Johannes Berg 6a9d1b91f3 mac80211: add pre-RCU-sync sta removal driver operation
Currently, mac80211 allows drivers to keep RCU-protected station
references that are cleared when the station is removed from the
driver and consequently needs to synchronize twice, once before
removing the station from the driver (so it can guarantee that
the station is no longer used in TX towards the driver) and once
after the station is removed from the driver.

Add a new pre-RCU-synchronisation station removal operation to
the API to allow drivers to clear/invalidate their RCU-protected
station pointers before the RCU synchronisation.

This will allow removing the second synchronisation by changing
the driver API so that the driver may no longer assume a valid
RCU-protected pointer after sta_remove/sta_state returns.

The alternative to this would be to synchronize_rcu() in all the
drivers that currently rely on this behaviour (only iwlmvm) but
that would defeat the purpose.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-16 11:29:44 +01:00
Johannes Berg c4de673b77 Merge remote-tracking branch 'wireless-next/master' into mac80211-next 2013-12-16 11:23:45 +01:00
Johannes Berg 18cfd3bfc9 Revert "mac80211: add driver callback for per-interface multicast filter"
This reverts commit 488b366a45.

The code isn't used by anyone, and the Intel driver isn't planning
to use it either right now.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-12-03 13:21:55 +01:00
John W. Linville 4b074b0762 Merge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next 2013-12-02 14:25:38 -05:00
Eliad Peller 21f659bf1f mac80211: add min required channel definition field
Add a new field to ieee80211_chanctx_conf to indicate
the min required channel configuration.

Tuning to a narrower channel might help reducing
the noise level and saving some power.

The min required channel definition is the max of
all min required channel definitions of the interfaces
bound to this channel context.

In AP mode, use 20MHz when there are no connected station.
When a new station is added/removed, calculate the new max
bandwidth supported by any of the stations (e.g. 80MHz when
80MHz and 40MHz stations are connected).

In other cases, simply use bss_conf.chandef as the
min required chandef.

Notify drivers about changes to this field by calling
drv_change_chanctx with a new CHANGE_MIN_WIDTH notification.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-11-25 20:52:05 +01:00
John W. Linville 9f96da4dd2 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem 2013-10-17 14:02:07 -04:00
Joe Perches d458cdf712 net:drivers/net: Miscellaneous conversions to ETH_ALEN
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.

Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-02 17:04:45 -04:00
Johannes Berg 55fff50113 mac80211: add explicit IBSS driver operations
This can be useful for drivers if they have any failure cases
when joining an IBSS. Also move setting the queue parameters
to before this new call, in case the new driver op needs them
already.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-10-01 12:17:45 +02:00
Simon Wunderlich 73da7d5bab mac80211: add channel switch command and beacon callbacks
The count field in CSA must be decremented with each beacon
transmitted. This patch implements the functionality for drivers
using ieee80211_beacon_get(). Other drivers must call back manually
after reaching count == 0.

This patch also contains the handling and finish worker for the channel
switch command, and mac80211/chanctx code to allow to change a channel
definition of an active channel context.

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[small cleanups, catch identical chandef]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-08-01 18:30:33 +02:00
Johannes Berg 85220d71bf mac80211: support secondary channel offset in CSA
Add support for the secondary channel offset IE in channel
switch announcements. This is necessary for proper handling
of CSA on HT access points.

For this to work it is also necessary to convert everything
here to use chandef structs instead of just channels. The
driver updates aren't really correct though. In particular,
the TI wl18xx driver update can't possibly be right since
it just ignores the new channel width for lack of firmware
API.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-04-16 15:29:44 +02:00
Karl Beldan 675a0b049a mac80211: Use a cfg80211_chan_def in ieee80211_hw_conf_chan
Drivers that don't use chanctxes cannot perform VHT association because
they still use a "backward compatibility" pair of {ieee80211_channel,
nl80211_channel_type} in ieee80211_conf and ieee80211_local.

Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
[fix kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-25 19:19:35 +01:00
Janusz Dziedzic 67baf66339 mac80211: add P2P NoA settings
Add P2P NoA settings for STA mode.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[fix docs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-22 14:13:42 +01:00
Johannes Berg 39ecc01d1b mac80211: pass queue bitmap to flush operation
There are a number of situations in which mac80211 only
really needs to flush queues for one virtual interface,
and in fact during this frames might be transmitted on
other virtual interfaces. Calculate and pass a queue
bitmap to the driver so it knows which queues to flush.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-18 20:15:03 +01:00
Alexander Bondar 488b366a45 mac80211: add driver callback for per-interface multicast filter
Some devices have multicast filter capability for each individual
virtual interface rather than just a global one. Add an interface
specific driver callback allowing such drivers to configure this.

Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-11 16:22:14 +02:00
Ilan Peer d339d5ca8e mac80211: Allow drivers to differentiate between ROC types
Some devices can handle remain on channel requests differently
based on the request type/priority. Add support to
differentiate between different ROC types, i.e., indicate that
the ROC is required for sending managment frames.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-03-06 16:35:49 +01:00
Seth Forshee 15ac7c478f mac80211: Fix incorrect use of STA_PR_FMT in trace points
Several tracepoints are using STA_PR_FMT where STA_PR_ARG should be
used, resulting in messages like "phy0 sta:ARG TYPE NOT FIELD BUT 1".
Change these to STA_PR_ARG.

Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-02-15 20:25:11 +01:00
Simon Wunderlich 164eb02d07 mac80211: add radar detection command/event
Add command to trigger radar detection in the driver/FW.
Once radar detection is started it should continuously
monitor for radars as long as the channel active.
If radar is detected usermode notified with 'radar
detected' event.

Scanning and remain on channel functionality must be disabled
while doing radar detection/scanning, and vice versa.

Based on original patch by Victor Goldenshtein <victorg@ti.com>

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-02-15 09:41:04 +01:00
Johannes Berg ef429dadf3 mac80211: introduce beacon-only timing data
In order to be able to predict the next DTIM TBTT
in the driver, add the ability to use timing data
from beacons only with the new hardware flag
IEEE80211_HW_TIMING_BEACON_ONLY and the BSS info
value sync_dtim_count which is only valid if the
timing data came from a beacon. The data can only
come from a beacon, and if no beacon was received
before association it is updated later together
with the DTIM count notification.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-02-11 18:45:00 +01:00
Johannes Berg 757af6fefd mac80211: fix chandef tracing bug
The chandef tracing writes center_freq1 twice, so
that it is always 0 (no driver supports 80+80 yet)
and leaves center_freq2 unset. Fix this mistake.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-02-11 18:44:56 +01:00
Emmanuel Grumbach 887da9176e mac80211: provide the vif in rssi_callback
Since drivers can support several BSS / P2P Client
interfaces, the rssi callback needs to inform the driver
about the interface teh rssi event relates to.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-24 15:41:29 +01:00
Johannes Berg a65240c101 mac80211: allow drivers to access IPv6 information
To be able to implement NS response offloading (in
regular operation or while in WoWLAN) drivers need
to know the IPv6 addresses assigned to interfaces.
Implement an IPv6 notifier in mac80211 to call the
driver when addresses change.

Unlike for IPv4, implement it as a callback rather
than as a list in the BSS configuration, that is
more flexible.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-18 21:55:38 +01:00
Johannes Berg 0f19b41e22 mac80211: remove ARP filter enable/disable logic
Depending on the driver, having ARP filtering for
some addresses may be possible. Remove the logic
that tracks whether ARP filter is enabled or not
and give the driver the total number of addresses
instead of the length of the list so it can make
its own decision.

Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-18 21:20:34 +01:00
Yoni Divinsky de5fad8157 mac80211: add op to configure default key id
There are hardwares which support offload of data packets
for example when auto ARP is enabled the hw will send
the ARP response. In such cases if WEP encryption is
configured the hw must know the default WEP key in order
to encrypt the packets correctly.

When hw_accel is enabled and encryption type is set to WEP,
the driver should get the default key index from mac80211.

Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
[cleanups, fixes, documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-18 13:30:21 +01:00
Johannes Berg 5a32aff37a mac80211: split out chandef tracing macros
Some new APIs will require tracing a chandef without
it being part of a channel context, so separate out
the tracing macros for that.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-16 23:57:51 +01:00
Johannes Berg 4bf88530be mac80211: convert to channel definition struct
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.

This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-26 12:42:59 +01:00
Johannes Berg 42d97a599e cfg80211: remove remain-on-channel channel type
As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.

Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-26 12:42:58 +01:00
Eliad Peller 4988456862 mac80211: make remain_on_channel() op pass vif param
Drivers (e.g. wl12xx) might need to know the vif
to roc on (mainly in order to configure the
rx filters correctly).

Add the vif to the op params, and update the current
users (iwlwifi) to use the new api.

Signed-off-by: Eliad Peller <eliad@wizery.com>
[fix hwsim]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-19 16:20:37 +01:00
Johannes Berg 9214ad7f9a mac80211: call driver method when restart completes
When the driver requests a restart (reconfiguration) it
gets all the normal method calls, but can't really tell
why they're happening. Call a new restart_complete op
in the driver when the restart completes, so it could
keep its own state about the restart and clear it there.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-09 17:34:35 +01:00
Johannes Berg 60762cbfeb mac80211: remove unused tracepoint
Clearly the tracepoint drv_offchannel_tx was
forgotten when that functionality was removed,
remove it now.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2012-11-09 17:30:50 +01:00