Pull more input updates from Dmitry Torokhov:
"Second round of updates for the input subsystem.
This introduces two brand new touchscreen drivers (Colibri and
imx6ul_tsc), some small driver fixes, and we are no longer report
errors from evdev_flush() as users do not really have a way of
handling errors, error codes that we were returning were not on the
list of errors supposed to be returned by close(), and errors were
causing issues with one of older versions of systemd"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: imx_keypad - remove obsolete comment
Input: touchscreen - add imx6ul_tsc driver support
Input: Add touchscreen support for Colibri VF50
Input: i8042 - lower log level for "no controller" message
Input: evdev - do not report errors form flush()
Input: elants_i2c - extend the calibration timeout to 12 seconds
Input: sparcspkr - fix module autoload for OF platform drivers
Input: regulator-haptic - fix module autoload for OF platform driver
Input: pwm-beeper - fix module autoload for OF platform driver
Input: ab8500-ponkey - Fix module autoload for OF platform driver
Input: cyttsp - remove unnecessary MODULE_ALIAS()
Input: elan_i2c - add ACPI ID "ELAN1000"
Pull watchdog updates from Wim Van Sebroeck:
- new driver for NXP LPC18xx Watchdog Timer
- new driver for SAMA5D4 watchdog timer
- add support for MCP79 to nv_tco driver
- clean-up and improvement of the mpc8xxx watchdog driver
- improvements to gpio-wdt
- at91sam9_wdt clock improvements
... and other small fixes and improvements
* git://www.linux-watchdog.org/linux-watchdog: (25 commits)
Watchdog: Fix parent of watchdog_devices
watchdog: at91rm9200: Correct check for syscon_node_to_regmap() errors
watchdog: at91sam9: get and use slow clock
Documentation: dt: binding: atmel-sama5d4-wdt: for SAMA5D4 watchdog driver
watchdog: add a driver to support SAMA5D4 watchdog timer
watchdog: mpc8xxx: allow to compile for MPC512x
watchdog: mpc8xxx: use better error code when watchdog cannot be enabled
watchdog: mpc8xxx: use dynamic memory for device specific data
watchdog: mpc8xxx: use devm_ioremap_resource to map memory
watchdog: mpc8xxx: make use of of_device_get_match_data
watchdog: mpc8xxx: simplify registration
watchdog: mpc8xxx: remove dead code
watchdog: lpc18xx_wdt_get_timeleft() can be static
DT: watchdog: Add NXP LPC18xx Watchdog Timer binding documentation
watchdog: NXP LPC18xx Watchdog Timer Driver
watchdog: gpio-wdt: ping already at startup for always running devices
watchdog: gpio-wdt: be more strict about hw_algo matching
Documentation: watchdog: at91sam9_wdt: add clocks property
watchdog: booke_wdt: Use infrastructure to check timeout limits
watchdog: (nv_tco) add support for MCP79
...
This is a collection of a few late fixes and other misc. stuff that
had dependencies on things being merged from other trees.
The bulk of the changes are for samsung/exynos SoCs for some changes
that needed a few minor reworks so ended up a bit late. The others
are mainly for qcom SoCs: a couple fixes and some DTS updates.
There's one conflict with drivers/cpufreq/exynos-cpufreq.c because
it's now been completely removed, but there were some fixes that hit
mainline in the meantime.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=85Ck
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM SoC updates from Kevin Hilman:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
The bulk of the changes are for samsung/exynos SoCs for some changes
that needed a few minor reworks so ended up a bit late. The others
are mainly for qcom SoCs: a couple fixes and some DTS updates"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
ARM: multi_v7_defconfig: Enable PBIAS regulator
soc: qcom: smd: Correct fBLOCKREADINTR handling
soc: qcom: smd: Use correct remote processor ID
soc: qcom: smem: Fix errant private access
ARM: dts: qcom: msm8974-sony-xperia-honami: Use stdout-path
ARM: dts: qcom: msm8960-cdp: Use stdout-path
ARM: dts: qcom: msm8660-surf: Use stdout-path
ARM: dts: qcom: ipq8064-ap148: Use stdout-path
ARM: dts: qcom: apq8084-mtp: Use stdout-path
ARM: dts: qcom: apq8084-ifc6540: Use stdout-path
ARM: dts: qcom: apq8074-dragonboard: Use stdout-path
ARM: dts: qcom: apq8064-ifc6410: Use stdout-path
ARM: dts: qcom: apq8064-cm-qs600: Use stdout-path
ARM: dts: qcom: Label serial nodes for aliasing and stdout-path
reset: ath79: Fix missing spin_lock_init
reset: Add (devm_)reset_control_get stub functions
ARM: EXYNOS: switch to using generic cpufreq driver for exynos4x12
cpufreq: exynos: Remove unselectable rule for arm-exynos-cpufreq.o
ARM: dts: add iommu property to JPEG device for exynos4
ARM: dts: enable SPI1 for exynos4412-odroidu3
...
This patch fixes SMEM addressing issues when remote processors need to use
secure SMEM partitions.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
The compatible "atmel,sama5d4-wdt" supports the SAMA5D4 watchdog driver
and the watchdog's WDT_MR register can be written more than once.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog has an input clock, the slow clock. It is required as it will
not function without it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This set of changes introduces the beginnings of a new API that's based
around the concept of states that can be atomically applied. Drivers go
to various lengths to implement something similar, which indicates that
the core should really be providing the necessary framework.
On top of that, there is a bit of cleanup as well as improved kerneldoc
and integration into the device-drivers DocBook.
Regarding drivers there is a new one for the NXP LPC18xx family of SoCs
and a couple of fixes for existing drivers (pca9685, Broadcom Kona and
Atmel HLCDC).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ymH8
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes introduces the beginnings of a new API that's
based around the concept of states that can be atomically applied.
Drivers go to various lengths to implement something similar, which
indicates that the core should really be providing the necessary
framework.
On top of that, there is a bit of cleanup as well as improved
kerneldoc and integration into the device-drivers DocBook.
Regarding drivers there is a new one for the NXP LPC18xx family of
SoCs and a couple of fixes for existing drivers (pca9685, Broadcom
Kona and Atmel HLCDC)"
* tag 'pwm/for-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
ARM: at91: pwm: atmel-hlcdc: Add at91sam9n12 errata
pwm: Add NXP LPC18xx PWM/SCT DT binding documentation
pwm: NXP LPC18xx PWM/SCT driver
pwm-pca9685: Support changing the output frequency
pwm-pca9685: Fix several driver bugs
pwm: kona: Modify settings application sequence
pwm: pca9685: Drop owner assignment
pwm: Add to device-drivers documentation
pwm: Clean up kerneldoc
pwm: Remove useless whitespace
pwm: sysfs: Remove unnecessary padding
pwm: sysfs: Properly convert from enum to string
pwm: Make use of pwm_get_xxx() helpers where appropriate
pwm: Add pwm_get_polarity() helper function
pwm: Constify PWM device where possible
pwm: Add the pwm_is_enabled() helper
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlXoqLgACgkQIXnXXONXEReNCwCghq2EtqGYTvLhupB4bJFCdtA5
ZJMAoIJ+1WIbvGJmBZ/RxehiCl/FjxTl
=+N3y
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.3' of git://git.code.sf.net/p/openipmi/linux-ipmi
Pull IPMI updates from Corey Minyard:
"Most of these have been sitting in linux-next for more than a release,
particularly commit 0fbcf4af7c ("ipmi: Convert the IPMI SI ACPI
handling to a platform device") which is probably the most complex
patch.
That is also the one that changes drivers/acpi/acpi_pnp.c. The change
in that file is only removing IPMI from a "special platform devices"
list, since I convert it to the standard PNP interface. I posted this
one to the ACPI list twice and got no response, and it seems to work
well in my testing, so I'm hoping it's good.
Hidehiro Kawai posted a set of changes that improves the panic time
handling in the IPMI driver.
The rest of the changes are minor bug fixes or cleanups and some
documentation"
* tag 'for-linus-4.3' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi:ssif: Add a module parm to specify that SMBus alerts don't work
ipmi: add of_device_id in MODULE_DEVICE_TABLE
ipmi: Compensate for BMCs that wont set the irq enable bit
ipmi: Don't call receive handler in the panic context
ipmi: Avoid touching possible corrupted lists in the panic context
ipmi: Don't flush messages in sender() in run-to-completion mode
ipmi: Factor out message flushing procedure
ipmi: Remove unneeded set_run_to_completion call
ipmi: Make some data const that was only read
ipmi: constify SSIF ACPI device ids
ipmi: Delete an unnecessary check before the function call "cleanup_one_si"
char:ipmi - Change 1 to true for bool type variables during initialization.
impi:Remove unneeded setting of module owner to THIS_MODULE in the platform structure, powernv_ipmi_driver
ipmi: Add a comment in how messages are delivered from the lower layer
ipmi/powernv: Fix potential invalid pointer dereference
ipmi: Convert the IPMI SI ACPI handling to a platform device
ipmi: Add device tree bindings information
This time the IOMMU updates are mostly cleanups or fixes. No big new
features or drivers this time. In particular the changes include:
* Bigger cleanup of the Domain<->IOMMU data structures and the
code that manages them in the Intel VT-d driver. This makes
the code easier to understand and maintain, and also easier to
keep the data structures in sync. It is also a preparation
step to make use of default domains from the IOMMU core in the
Intel VT-d driver.
* Fixes for a couple of DMA-API misuses in ARM IOMMU drivers,
namely in the ARM and Tegra SMMU drivers.
* Fix for a potential buffer overflow in the OMAP iommu driver's
debug code
* A couple of smaller fixes and cleanups in various drivers
* One small new feature: Report domain-id usage in the Intel
VT-d driver to easier detect bugs where these are leaked.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=yoGE
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates for from Joerg Roedel:
"This time the IOMMU updates are mostly cleanups or fixes. No big new
features or drivers this time. In particular the changes include:
- Bigger cleanup of the Domain<->IOMMU data structures and the code
that manages them in the Intel VT-d driver. This makes the code
easier to understand and maintain, and also easier to keep the data
structures in sync. It is also a preparation step to make use of
default domains from the IOMMU core in the Intel VT-d driver.
- Fixes for a couple of DMA-API misuses in ARM IOMMU drivers, namely
in the ARM and Tegra SMMU drivers.
- Fix for a potential buffer overflow in the OMAP iommu driver's
debug code
- A couple of smaller fixes and cleanups in various drivers
- One small new feature: Report domain-id usage in the Intel VT-d
driver to easier detect bugs where these are leaked"
* tag 'iommu-updates-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (83 commits)
iommu/vt-d: Really use upper context table when necessary
x86/vt-d: Fix documentation of DRHD
iommu/fsl: Really fix init section(s) content
iommu/io-pgtable-arm: Unmap and free table when overwriting with block
iommu/io-pgtable-arm: Move init-fn declarations to io-pgtable.h
iommu/msm: Use BUG_ON instead of if () BUG()
iommu/vt-d: Access iomem correctly
iommu/vt-d: Make two functions static
iommu/vt-d: Use BUG_ON instead of if () BUG()
iommu/vt-d: Return false instead of 0 in irq_remapping_cap()
iommu/amd: Use BUG_ON instead of if () BUG()
iommu/amd: Make a symbol static
iommu/amd: Simplify allocation in irq_remapping_alloc()
iommu/tegra-smmu: Parameterize number of TLB lines
iommu/tegra-smmu: Factor out tegra_smmu_set_pde()
iommu/tegra-smmu: Extract tegra_smmu_pte_get_use()
iommu/tegra-smmu: Use __GFP_ZERO to allocate zeroed pages
iommu/tegra-smmu: Remove PageReserved manipulation
iommu/tegra-smmu: Convert to use DMA API
iommu/tegra-smmu: smmu_flush_ptc() wants device addresses
...
- Fix a race condition in the request handling
- Skip trim commands for some buggy kingston eMMCs
- An optimization and a correction for erase groups
- Set CMD23 quirk for some Sandisk cards
MMC host:
- sdhci: Give GPIO CD higher precedence and don't poll when it's used
- sdhci: Fix DMA memory leakage
- sdhci: Some updates for clock management
- sdhci-of-at91: introduce driver for the Atmel SDMMC
- sdhci-of-arasan: Add support for sdhci-5.1
- sdhci-esdhc-imx: Add support for imx7d which also supports HS400
- sdhci: A collection of fixes and improvements for various sdhci hosts
- omap_hsmmc: Modernization of the regulator code
- dw_mmc: A couple of fixes for DMA and PIO mode
- usdhi6rol0: A few fixes and support probe deferral for regulators
- pxamci: Convert to use dmaengine
- sh_mmcif: Fix the suspend process in a short term solution
- tmio: Adjust timeout for commands
- sunxi: Fix timeout while gating/ungating clock
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wR1C
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.3' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Fix a race condition in the request handling
- Skip trim commands for some buggy kingston eMMCs
- An optimization and a correction for erase groups
- Set CMD23 quirk for some Sandisk cards
MMC host:
- sdhci: Give GPIO CD higher precedence and don't poll when it's used
- sdhci: Fix DMA memory leakage
- sdhci: Some updates for clock management
- sdhci-of-at91: introduce driver for the Atmel SDMMC
- sdhci-of-arasan: Add support for sdhci-5.1
- sdhci-esdhc-imx: Add support for imx7d which also supports HS400
- sdhci: A collection of fixes and improvements for various sdhci hosts
- omap_hsmmc: Modernization of the regulator code
- dw_mmc: A couple of fixes for DMA and PIO mode
- usdhi6rol0: A few fixes and support probe deferral for regulators
- pxamci: Convert to use dmaengine
- sh_mmcif: Fix the suspend process in a short term solution
- tmio: Adjust timeout for commands
- sunxi: Fix timeout while gating/ungating clock"
* tag 'mmc-v4.3' of git://git.linaro.org/people/ulf.hansson/mmc: (67 commits)
mmc: android-goldfish: remove incorrect __iomem annotation
mmc: core: fix race condition in mmc_wait_data_done
mmc: host: omap_hsmmc: remove CONFIG_REGULATOR check
mmc: host: omap_hsmmc: use ios->vdd for setting vmmc voltage
mmc: host: omap_hsmmc: use regulator_is_enabled to find pbias status
mmc: host: omap_hsmmc: enable/disable vmmc_aux regulator based on previous state
mmc: host: omap_hsmmc: don't use ->set_power to set initial regulator state
mmc: host: omap_hsmmc: avoid pbias regulator enable on power off
mmc: host: omap_hsmmc: add separate function to set pbias
mmc: host: omap_hsmmc: add separate functions for enable/disable supply
mmc: host: omap_hsmmc: return error if any of the regulator APIs fail
mmc: host: omap_hsmmc: remove unnecessary pbias set_voltage
mmc: host: omap_hsmmc: use mmc_host's vmmc and vqmmc
mmc: host: omap_hsmmc: use the ocrmask provided by the vmmc regulator
mmc: host: omap_hsmmc: cleanup omap_hsmmc_reg_get()
mmc: host: omap_hsmmc: return on fatal errors from omap_hsmmc_reg_get
mmc: host: omap_hsmmc: use devm_regulator_get_optional() for vmmc
mmc: sdhci-of-at91: fix platform_no_drv_owner.cocci warnings
mmc: sh_mmcif: Fix suspend process
mmc: usdhi6rol0: fix error return code
...
Pull i2c updates from Wolfram Sang:
"Features:
- new drivers: Renesas EMEV2, register based MUX, NXP LPC2xxx
- core: scans DT and assigns wakeup interrupts. no driver changes needed.
- core: some refcouting issues fixed and better API for that
- core: new helper function for best effort block read emulation
- slave framework: proper DT bindings and userspace instantiation
- some bigger work for xiic, pxa, omap drivers
.. and quite a number of smaller driver fixes, cleanups, improvements"
* 'i2c/for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (65 commits)
i2c: mux: reg Change ioread endianness for readback
i2c: mux: reg: fix compilation warnings
i2c: mux: reg: simplify register size checking
i2c: muxes: fix leaked i2c adapter device node references
i2c: allow specifying separate wakeup interrupt in device tree
of/irq: export of_get_irq_byname()
i2c: xgene-slimpro: dma_mapping_error() doesn't return an error code
i2c: Replace I2C_CROS_EC_TUNNEL dependency
eeprom: at24: use i2c_smbus_read_i2c_block_data_or_emulated
i2c: core: Add support for best effort block read emulation
i2c: lpc2k: add driver
i2c: mux: Add register-based mux i2c-mux-reg
i2c: dt: describe generic bindings
i2c: slave: print warning if slave flag not set
i2c: support 10 bit and slave addresses in sysfs 'new_device'
i2c: take address space into account when checking for used addresses
i2c: apply DT flags when probing
i2c: make address check indpendent from client struct
i2c: rename address check functions
i2c: apply address offset for slaves, too
...
Core:
- use is_visible() to control sysfs attributes
- switch wakealarm attribute to DEVICE_ATTR_RW
- make rtc_does_wakealarm() return boolean
- properly manage lifetime of dev and cdev in rtc device
- remove unnecessary device_get() in rtc_device_unregister
- fix double free in rtc_register_device() error path
New drivers:
- NXP LPC24xx
- Xilinx Zynq MP
- Dialog DA9062
Subsystem wide cleanups:
- fix drivers that consider 0 as a valid IRQ in client->irq
- Drop (un)likely before IS_ERR(_OR_NULL)
- drop the remaining owner assignment for i2c_driver and platform_driver
- module autoload fixes
Drivers:
- 88pm80x: add device tree support
- abx80x: fix RTC write bit
- ab8500: Add a sentinel to ab85xx_rtc_ids[]
- armada38x: Align RTC set time procedure with the official errata
- as3722: correct month value
- at91sam9: cleanups
- at91rm9200: get and use slow clock and cleanups
- bq32k: remove redundant check
- cmos: century support, proper fix for the spurious wakeup
- ds1307: cleanups and wakeup irq support
- ds1374: Remove unused variable
- ds1685: Use module_platform_driver
- ds3232: fix WARNING trace in resume function
- gemini: fix ptr_ret.cocci warnings
- mt6397: implement suspend/resume
- omap: support internal and external clock enabling
- opal: Enable alarms only when opal supports tpo
- pcf2127: use OFS flag to detect unreliable date and warn the user
- pl031: fix typo for author email
- rx8025: huge cleanup and fixes
- sa1100/pxa: share common code
- s5m: fix to update ctrl register
- s3c: fix clocks and wakeup, cleanup
- sirfsoc: use regmap
- nvram_read()/nvram_write() functions for cmos, ds1305, ds1307, ds1343,
ds1511, ds1553, ds1742, m48t59, rp5c01, stk17ta8, tx4939
- use rtc_valid_tm() error code when reading date/time instead of 0 for
isl12022, pcf2123, pcf2127
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCAAGBQJV7ARpAAoJEKbNnwlvZCyzo40P/09fca3C9HBEI5hgJO7PmQX8
+3wkacMjEi58yMTzWoDCFh2H1Vvajm1d6bJ6H//5/3h/KPKrjIsCTFlMfuv8gfbe
xFoeXPMdiojjPxFjbjnpM+0GD9SKTIjwpP4d8HgoUDwGRJ6dxaTOVuJXRmVGcmas
e4Ih6hDy2YBiRXLzLHSvSNcTJDGznwMvEEg1AfqUjAtNm4BUzhUnvq0CYlSdwMzy
xK6w0LmOr67l2QpjiQNCvIn04OWdDQ35f0GcRHYEY66cZPkvPp3OCC/UbeChU6uK
He/v1n+QdBTbkKYeYmNnBSr42KPTLONNaOFXf79PpAz/WtiYxLxJDbf8DYW9gGQj
mC3rMNWXf4rEFHkHYH4KvbvxplYd6/pCByMFJa76pKtcE2FG7pVAQZgLaLGemct4
q0MW73n7yBR1wDlTHqqKu1pAnz1CW3Eui96mDJJptG3CtNqe9a8G48Yzy5OuYAcI
wxBWCbxeT2z+EuePOBGlQvPreyqyTjHXL87NqMEDrzFrdQd02rn90xqIPlCbcr/P
qyRwIrDGFyV8PX9I4ewrtt9WfgttayHgZ4juaSi9F479oT6006z6vArrTg2Q/saA
b0X+hG8oLGSZuSobASjjCtjTE+jYhr+4hzGuHJw0ky0CzLQOqf1APMKDwLN4m5Pz
Ex+JKalozL+LElGMCS3q
=cKuu
-----END PGP SIGNATURE-----
Merge tag 'rtc-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Core:
- use is_visible() to control sysfs attributes
- switch wakealarm attribute to DEVICE_ATTR_RW
- make rtc_does_wakealarm() return boolean
- properly manage lifetime of dev and cdev in rtc device
- remove unnecessary device_get() in rtc_device_unregister
- fix double free in rtc_register_device() error path
New drivers:
- NXP LPC24xx
- Xilinx Zynq MP
- Dialog DA9062
Subsystem wide cleanups:
- fix drivers that consider 0 as a valid IRQ in client->irq
- Drop (un)likely before IS_ERR(_OR_NULL)
- drop the remaining owner assignment for i2c_driver and
platform_driver
- module autoload fixes
Drivers:
- 88pm80x: add device tree support
- abx80x: fix RTC write bit
- ab8500: Add a sentinel to ab85xx_rtc_ids[]
- armada38x: Align RTC set time procedure with the official errata
- as3722: correct month value
- at91sam9: cleanups
- at91rm9200: get and use slow clock and cleanups
- bq32k: remove redundant check
- cmos: century support, proper fix for the spurious wakeup
- ds1307: cleanups and wakeup irq support
- ds1374: Remove unused variable
- ds1685: Use module_platform_driver
- ds3232: fix WARNING trace in resume function
- gemini: fix ptr_ret.cocci warnings
- mt6397: implement suspend/resume
- omap: support internal and external clock enabling
- opal: Enable alarms only when opal supports tpo
- pcf2127: use OFS flag to detect unreliable date and warn the user
- pl031: fix typo for author email
- rx8025: huge cleanup and fixes
- sa1100/pxa: share common code
- s5m: fix to update ctrl register
- s3c: fix clocks and wakeup, cleanup
- sirfsoc: use regmap
- nvram_read()/nvram_write() functions for cmos, ds1305, ds1307,
ds1343, ds1511, ds1553, ds1742, m48t59, rp5c01, stk17ta8, tx4939
- use rtc_valid_tm() error code when reading date/time instead of 0
for isl12022, pcf2123, pcf2127"
* tag 'rtc-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (90 commits)
rtc: abx80x: fix RTC write bit
rtc: ab8500: Add a sentinel to ab85xx_rtc_ids[]
rtc: ds1374: Remove unused variable
rtc: Fix module autoload for OF platform drivers
rtc: Fix module autoload for rtc-{ab8500,max8997,s5m} drivers
rtc: omap: Add external clock enabling support
rtc: omap: Add internal clock enabling support
ARM: dts: AM437x: Add the internal and external clock nodes for rtc
rtc: s5m: fix to update ctrl register
rtc: add xilinx zynqmp rtc driver
devicetree: bindings: rtc: add bindings for xilinx zynqmp rtc
rtc: as3722: correct month value
ARM: config: Switch PXA27x platforms to use PXA RTC driver
ARM: mmp: remove unused RTC register definitions
ARM: sa1100: remove unused RTC register definitions
rtc: sa1100/pxa: convert to run-time register mapping
ARM: pxa: add memory resource to SA1100 RTC device
rtc: pxa: convert to use shared sa1100 functions
rtc: sa1100: prepare to share sa1100_rtc_ops
rtc: ds3232: fix WARNING trace in resume function
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJV6ifEAAoJEAhfPr2O5OEVn5kP/i2jM1tWcmV/ZEBKGAN0jpRk
5Y/Q+rnXvOpIJSQC3dEkweoBymVMclSgSB/wFSWCZtp5MaB8KrH4/2uc3UvolF91
7bqXt+fCUacMbDQyaabMCR83mz9tdOJLd5sf0ABqBgXGfwh5uXmBPaYBzmcYvKcW
4D89MFUpaFDPARTs9rdpVyr0aPRU4GcN0R3snRO9Ly+cQnyV/RxPf9NqCgnI+yPq
+NvA9ScUBcBt62piSIGR4egcAR8boxYC+0r57340S21/JVMvsHQ3ok9b1aT8/rtd
Yl24FkcKrRV0ShN5S1RmW5DLH/HRGabuMjkiEz9xq52FGD2sQQda0At58dWivsa4
XYdxS9UUfb9Z+qyeMdmCl1MUFRrV2G4H6VItP+GKyT3UZLEDcLl6hBg3SkyWxWB4
CSO5WuRThiIB86OVcIaREftzqDy5HdvH3ZKRD7QrW0DItGVjQwV5j6gvwqO9OEXs
99BnSohyKwUBonumE2ZtFGGhIwIomllrMSqg991bPH9+13bg/rPxUqntkPrVap/9
cV3qKO8ZFrz5UInBnR1U83l60ZK7rV4G6AVMSMKpM9XVK9TDKryAUN9Mhj5XWRH8
hbma89TQVdhdrITtt27uzj8F622cvZvxd1BqDBR8DjKVvtv/E2GPzJrAj7GHe3/o
NgzP5fF6X2Si32GNb7J8
=cIed
-----END PGP SIGNATURE-----
Merge tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new DVB frontend drivers: ascot2e, cxd2841er, horus3a, lnbh25
- new HDMI capture driver: tc358743
- new driver for NetUP DVB new boards (netup_unidvb)
- IR support for DVBSky cards (smipcie-ir)
- Coda driver has gain macroblock tiling support
- Renesas R-Car gains JPEG codec driver
- new DVB platform driver for STi boards: c8sectpfe
- added documentation for the media core kABI to device-drivers DocBook
- lots of driver fixups, cleanups and improvements
* tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (297 commits)
[media] c8sectpfe: Remove select on undefined LIBELF_32
[media] i2c: fix platform_no_drv_owner.cocci warnings
[media] cx231xx: Use wake_up_interruptible() instead of wake_up_interruptible_nr()
[media] tc358743: only queue subdev notifications if devnode is set
[media] tc358743: add missing Kconfig dependency/select
[media] c8sectpfe: Use %pad to print 'dma_addr_t'
[media] DocBook media: Fix typo "the the" in xml files
[media] tc358743: make reset gpio optional
[media] tc358743: set direction of reset gpio using devm_gpiod_get
[media] dvbdev: document most of the functions/data structs
[media] dvb_frontend.h: document the struct dvb_frontend
[media] dvb-frontend.h: document struct dtv_frontend_properties
[media] dvb-frontend.h: document struct dvb_frontend_ops
[media] dvb: Use DVBFE_ALGO_HW where applicable
[media] dvb_frontend.h: document struct analog_demod_ops
[media] dvb_frontend.h: Document struct dvb_tuner_ops
[media] Docbook: Document struct analog_parameters
[media] dvb_frontend.h: get rid of dvbfe_modcod
[media] add documentation for struct dvb_tuner_info
[media] dvb_frontend: document dvb_frontend_tune_settings
...
Freescale i.MX6UL contains a internal touchscreen controller,
this patch add a driver to support this controller.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Colibri Vybrid VF50 module supports 4-wire touchscreens using
FETs and ADC inputs. This driver uses the IIO consumer interface
and relies on the vf610_adc driver based on the IIO framework.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
rtc can either be supplied from internal 32k clock or external crystal
generated 32k clock. Internal clock is SOC specific and the external
clock is board dependent. Adding the corresponding nodes.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
adds file for description on device node bindings for RTC
found on Xilinx Zynq Ultrascale+ MPSoC.
Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm for 4.3. Nouveau is
probably the biggest amount of changes in here, since it missed 4.2.
Highlights below, along with the usual bunch of fixes.
All stuff outside drm should have applicable acks.
Highlights:
- new drivers:
freescale dcu kms driver
- core:
more atomic fixes
disable some dri1 interfaces on kms drivers
drop fb panic handling, this was just getting more broken, as more locking was required.
new core fbdev Kconfig support - instead of each driver enable/disabling it
struct_mutex cleanups
- panel:
more new panels
cleanup Kconfig
- i915:
Skylake support enabled by default
legacy modesetting using atomic infrastructure
Skylake fixes
GEN9 workarounds
- amdgpu:
Fiji support
CGS support for amdgpu
Initial GPU scheduler - off by default
Lots of bug fixes and optimisations.
- radeon:
DP fixes
misc fixes
- amdkfd:
Add Carrizo support for amdkfd using amdgpu.
- nouveau:
long pending cleanup to complete driver,
fully bisectable which makes it larger,
perfmon work
more reclocking improvements
maxwell displayport fixes
- vmwgfx:
new DX device support, supports OpenGL 3.3
screen targets support
- mgag200:
G200eW support
G200e new revision support
- msm:
dragonboard 410c support, msm8x94 support, msm8x74v1 support
yuv format support
dma plane support
mdp5 rotation
initial hdcp
- sti:
atomic support
- exynos:
lots of cleanups
atomic modesetting/pageflipping support
render node support
- tegra:
tegra210 support (dc, dsi, dp/hdmi)
dpms with atomic modesetting support
- atmel:
support for 3 more atmel SoCs
new input formats, PRIME support.
- dwhdmi:
preparing to add audio support
- rockchip:
yuv plane support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1369 commits)
drm/amdgpu: rename gmc_v8_0_init_compute_vmid
drm/amdgpu: fix vce3 instance handling
drm/amdgpu: remove ib test for the second VCE Ring
drm/amdgpu: properly enable VM fault interrupts
drm/amdgpu: fix warning in scheduler
drm/amdgpu: fix buffer placement under memory pressure
drm/amdgpu/cz: fix cz_dpm_update_low_memory_pstate logic
drm/amdgpu: fix typo in dce11 watermark setup
drm/amdgpu: fix typo in dce10 watermark setup
drm/amdgpu: use top down allocation for non-CPU accessible vram
drm/amdgpu: be explicit about cpu vram access for driver BOs (v2)
drm/amdgpu: set MEC doorbell range for Fiji
drm/amdgpu: implement burst NOP for SDMA
drm/amdgpu: add insert_nop ring func and default implementation
drm/amdgpu: add amdgpu_get_sdma_instance helper function
drm/amdgpu: add AMDGPU_MAX_SDMA_INSTANCES
drm/amdgpu: add burst_nop flag for sdma
drm/amdgpu: add count field for the SDMA NOP packet v2
drm/amdgpu: use PT for VM sync on unmap
drm/amdgpu: make wait_event uninterruptible in push_job
...
There are little changes in core part, but lots of development are
found in drivers, especially ASoC. The diffstat shows regmap-
related changes for a slight API additions / changes, and that's all.
Looking at the code size statistics, the most significant addition
is for Intel Skylake. (Note that SKL support is still underway, the
codec driver is missing.) Also STI controller driver is a major
addition as well as a few new codec drivers.
In HD-audio side, there are fewer changes than the past. The
noticeable change is the support of ELD notification from i915
graphics driver. Thus this pull request carries a few changes in
drm/i915.
Other than that, USB-audio got a rewrite of runtime PM code. It
was initiated by lockdep warning, but resulted in a good cleanup in
the end.
Below are the highlights:
Common:
- Factoring out of AC'97 reset code from ASoC into the core helper
- A few regmap API extensions (in case it's not pulled yet)
ASoC:
- New drivers for Cirrus CS4349, GTM601, InvenSense ICS43432, Realtek
RT298 and ST STI controllers
- Machine drivers for Rockchip systems with MAX98090 and RT5645 and
RT5650
- Initial driver support for Intel Skylake devices
- Lots of rsnd cleanup and enhancements
- A few DAPM fixes and cleanups
- A large number of cleanups in various drivers (conversion and
standardized to regmap, component) mostly by Lars-Peter and Axel
HD-audio:
- Extended HD-audio core for Intel Skylake controller support
- Quirks for Dell headsets, Alienware 15
- Clean up of pin-based quirk tables for Realtek codecs
- ELD notifier implenetation for Intel HDMI/DP
USB-audio:
- Refactor runtime PM code to make lockdep happier
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/sXs
-----END PGP SIGNATURE-----
Merge tag 'sound-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There are little changes in core part, but lots of development are
found in drivers, especially ASoC. The diffstat shows regmap-related
changes for a slight API additions / changes, and that's all.
Looking at the code size statistics, the most significant addition is
for Intel Skylake. (Note that SKL support is still underway, the
codec driver is missing.) Also STI controller driver is a major
addition as well as a few new codec drivers.
In HD-audio side, there are fewer changes than the past. The
noticeable change is the support of ELD notification from i915
graphics driver. Thus this pull request carries a few changes in
drm/i915.
Other than that, USB-audio got a rewrite of runtime PM code. It was
initiated by lockdep warning, but resulted in a good cleanup in the
end.
Below are the highlights:
Common:
- Factoring out of AC'97 reset code from ASoC into the core helper
- A few regmap API extensions (in case it's not pulled yet)
ASoC:
- New drivers for Cirrus CS4349, GTM601, InvenSense ICS43432, Realtek
RT298 and ST STI controllers
- Machine drivers for Rockchip systems with MAX98090 and RT5645 and
RT5650
- Initial driver support for Intel Skylake devices
- Lots of rsnd cleanup and enhancements
- A few DAPM fixes and cleanups
- A large number of cleanups in various drivers (conversion and
standardized to regmap, component) mostly by Lars-Peter and Axel
HD-audio:
- Extended HD-audio core for Intel Skylake controller support
- Quirks for Dell headsets, Alienware 15
- Clean up of pin-based quirk tables for Realtek codecs
- ELD notifier implenetation for Intel HDMI/DP
USB-audio:
- Refactor runtime PM code to make lockdep happier"
* tag 'sound-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (411 commits)
drm/i915: Add locks around audio component bind/unbind
drm/i915: Drop port_mst_index parameter from pin/eld callback
ALSA: hda - Fix missing inline for dummy snd_hdac_set_codec_wakeup()
ALSA: hda - Wake the codec up on pin/ELD notify events
ALSA: hda - allow codecs to access the i915 pin/ELD callback
drm/i915: Call audio pin/ELD notify function
drm/i915: Add audio pin sense / ELD callback
ASoC: zx296702-i2s: Fix resource leak when unload module
ASoC: sti_uniperif: Ensure component is unregistered when unload module
ASoC: au1x: psc-i2s: Convert to use devm_ioremap_resource
ASoC: sh: dma-sh7760: Convert to devm_snd_soc_register_platform
ASoC: spear_pcm: Use devm_snd_dmaengine_pcm_register to fix resource leak
ALSA: fireworks/bebob/dice/oxfw: fix substreams counting at vmalloc failure
ASoC: Clean up docbook warnings
ASoC: txx9: Convert to devm_snd_soc_register_platform
ASoC: pxa: Convert to devm_snd_soc_register_platform
ASoC: nuc900: Convert to devm_snd_soc_register_platform
ASoC: blackfin: Convert to devm_snd_soc_register_platform
ASoC: au1x: Convert to devm_snd_soc_register_platform
ASoC: qcom: Constify asoc_qcom_lpass_cpu_dai_ops
...
- Move PWM8941 WLED driver into Backlight
- Remove invalid use of IS_ERR_VALUE() macro
- Remove duplicate check for NULL data before unregistering
- Export I2C Device ID structure
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJV6FPVAAoJEFGvii+H/Hdh1NIP/2mcBwvmF8zgmTUALbRLKyAp
3LXx0/Nh64Pjz2rDsZPclo4NLlq43d9xq/A3CBI4b00VgiofgRG/Cihhzo8nxhTu
XN73TgVQ2CiNrQ0yn85dedoVEbv0cAlZYdyuHrp1SUUSPOUhaiRU2w6k7BkY0gc2
8lkzmVnMOkQjT+Elj6wVBcPiojm333Tu5wE125W8t6XDOwDfpLoVkzcxcv/V7eIo
pStB7u3MsXZ9kmG2S9aMSZX1PS6C772OeN1I7+3lFy67qiIDj3tQ+8MyaMFvWGdQ
/w8+f4K8k0t1m1OJVLgsT4UKR/7qprTOvEXYGrsVPPwZqSOypRZOooPOQbAVtkV6
qYsVYEnbsJerkCuAyWETL+H5eH+P56Zl66t6a9hgnzw4wKYarufo+xUe0b+ntmoO
dtegXgUVryY1P9teXsnnWx24r4pfaCWunO1RUXSZABCK+0qEeXa2SM/PFtkCWwEd
AGBp8Rcv9a2BHtY2oaii+rs6WFUH+CGeZ8rt1cKBZvT2gCjlTPb5WiGvCEnN3OBi
BCWgTLILldSRG7ERW6P6W6WkpP9u6gz8BChLNe0PsoOoNLXElHj6VCAlusOc1kHU
6WwvMpKcQ+SVMVNouFLv3Ur5K8sF7VkyaHDRoipeKufu0n3b3+AXEaRr/Ch1BsIh
cdUHgYJSujzcD/Zx8crp
=URbg
-----END PGP SIGNATURE-----
Merge tag 'backlight-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
- Stop using LP855X Platform Data to control regulators
- Move PWM8941 WLED driver into Backlight
- Remove invalid use of IS_ERR_VALUE() macro
- Remove duplicate check for NULL data before unregistering
- Export I2C Device ID structure
* tag 'backlight-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: tosa: Export I2C module alias information
backlight: lp8788_bl: Delete a check before backlight_device_unregister()
backlight: sky81452: Remove unneeded use of IS_ERR_VALUE() macro
backlight: pm8941-wled: Move PM8941 WLED driver to backlight
backlight: lp855x: Use private data for regulator control
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
- Core Frameworks
- New Base API to traverse devices and their children in reverse order
- Bug Fixes
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
- Fix-ups
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2blS
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support:
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
Core Frameworks:
- New Base API to traverse devices and their children in reverse order
Bug Fixes:
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
Fix-ups:
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures"
* tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: jz4740-adc: Init mask cache in generic IRQ chip
mfd: cros_ec: spi: Add OF match table
mfd: stmpe: Add OF match table
mfd: max77686: Split out regulator part from the DT binding
mfd: Add DT binding for Maxim MAX77802 IC
mfd: max77686: Use a generic name for the PMIC node in the example
mfd: max77686: Don't suggest in binding to use a deprecated property
mfd: Add MFD_CROS_EC dependencies
mfd: cros_ec: Remove CROS_EC_PROTO dependency for SPI and I2C drivers
mfd: axp20x: Add a cell for the usb power_supply part of the axp20x PMICs
mfd: axp20x: Add missing registers, and mark more registers volatile
mfd: arizona: Fixup some formatting/white space errors
mfd: wm8994: Fix NULL pointer exception on missing pdata
of: Add vendor prefix for Nuvoton
mfd: mt6397: Implement wake handler and suspend/resume to handle wake up event
mfd: atmel-hlcdc: Add support for new SoCs
mfd: Export OF module alias information in missing drivers
mfd: stw481x: Export I2C module alias information
mfd: da9062: Support for the DA9063 OnKey in the DA9062 core
mfd: max899x: Avoid redundant irq_data lookup
...
This time we have aded a new capability for scatter-gathered memset using
dmaengine APIs. This is supported in xdmac & hdmac drivers
We have added support for reusing descriptors for examples like video
buffers etc. Driver will follow
The behaviour of descriptor ack has been clarified and documented
New devices added are:
- dma controller in sun[457]i SoCs
- lpc18xx dmamux
- ZTE ZX296702 dma controller
- Analog Devices AXI-DMAC DMA controller
- eDMA support for dma-crossbar
- imx6sx support in imx-sdma driver
- imx-sdma device to device support
Others
- jz4780 fixes
- ioatdma large refactor and cleanup for removal of ioat v1 and v2 which is
deprecated and fixes
- ACPI support in X-Gene DMA engine driver
- ipu irq fixes
- mvxor fixes
- minor fixes spread thru drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gQZ6
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have aded a new capability for scatter-gathered memset
using dmaengine APIs. This is supported in xdmac & hdmac drivers
We have added support for reusing descriptors for examples like video
buffers etc. Driver will follow
The behaviour of descriptor ack has been clarified and documented
New devices added are:
- dma controller in sun[457]i SoCs
- lpc18xx dmamux
- ZTE ZX296702 dma controller
- Analog Devices AXI-DMAC DMA controller
- eDMA support for dma-crossbar
- imx6sx support in imx-sdma driver
- imx-sdma device to device support
Other:
- jz4780 fixes
- ioatdma large refactor and cleanup for removal of ioat v1 and v2
which is deprecated and fixes
- ACPI support in X-Gene DMA engine driver
- ipu irq fixes
- mvxor fixes
- minor fixes spread thru drivers"
[ The Kconfig and Makefile entries got re-sorted alphabetically, and I
handled the conflict with the new Intel integrated IDMA driver by
slightly mis-sorting it on purpose: "IDMA64" got sorted after "IMX" in
order to keep the Intel entries together. I think it might be a good
idea to just rename the IDMA64 config entry to INTEL_IDMA64 to make
the sorting be a true sort, not this mismash.
Also, this merge disables the COMPILE_TEST for the sun4i DMA
controller, because it does not compile cleanly at all. - Linus ]
* tag 'dmaengine-4.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (89 commits)
dmaengine: ioatdma: add Broadwell EP ioatdma PCI dev IDs
dmaengine :ipu: change ipu_irq_handler() to remove compile warning
dmaengine: ioatdma: Fix variable array length
dmaengine: ioatdma: fix sparse "error" with prep lock
dmaengine: hdmac: Add memset capabilities
dmaengine: sort the sh Makefile
dmaengine: sort the sh Kconfig
dmaengine: sort the dw Kconfig
dmaengine: sort the Kconfig
dmaengine: sort the makefile
drivers/dma: make mv_xor.c driver explicitly non-modular
dmaengine: Add support for the Analog Devices AXI-DMAC DMA controller
devicetree: Add bindings documentation for Analog Devices AXI-DMAC
dmaengine: xgene-dma: Fix the lock to allow client for further submission of requests
dmaengine: ioatdma: fix coccinelle warning
dmaengine: ioatdma: fix zero day warning on incompatible pointer type
dmaengine: tegra-apb: Simplify locking for device using global pause
dmaengine: tegra-apb: Remove unnecessary return statements and variables
dmaengine: tegra-apb: Avoid unnecessary channel base address calculation
dmaengine: tegra-apb: Remove unused variables
...
cycle
Core changes:
- It is possible configure groups in debugfs.
- Consolidation of chained IRQ handler install/remove replacing
all call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a
combined call to irq_set_chained_handler_and_data(). This
series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which
is way cleaner.
- Tglx also wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs
from IRQ numbers. The goal is to get rid of the irq number
from the handlers in the IRQ flow which is nice.
Driver feature enhancements:
- Power management support for the SiRF SoC Atlas 7.
- Power down support for the Qualcomm driver.
- Intel Cherryview and Baytrail: switch drivers to use raw
spinlocks in IRQ handlers to play nice with the realtime
patch set.
- Rework and new modes handling for Qualcomm SPMI-MPP.
- Pinconf power source config for SH PFC.
New drivers and subdrivers:
- A new driver for Conexant Digicolor CX92755.
- A new driver for UniPhier PH1-LD4, PH1-Pro4, PH1-sLD8,
PH1-Pro5, ProXtream2 and PH1-LD6b SoC pin control support.
- Reverse-egineered the S/PDIF settings for the Allwinner
sun4i driver.
- Support for Qualcomm Technologies QDF2xxx ARM64 SoCs
- A new Freescale i.mx6ul subdriver.
Cleanup:
- Remove platform data support in a number of SH PFC
subdrivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJV6YzgAAoJEEEQszewGV1zbIAQAILzMrzWkxsy7bhvL4QdP5/K
OG3EodE//AE0G5gKugUDjg5t2lftdiIJVhjDA17ruETCSciuAxZSLThlMy1sQgyN
LPxy9LlCrmsqrYt9+fmJ9js8j52RBJikKK0RUyUVz0VojTBplRpElyEx/KxwM5sG
Hy3+hU61uKO0j9AyIcsa/RKP6SGavwZdHytJBsHNw+pODyE3UZCf52ChAVBsTPfE
MV70g3Qzfqur7ZFqcNgtUV7qCyYvlF12ooiihrGFDOsTL3sSq4/OXB7z1z1mGGHL
Dgq8pXJ6EIZlCbk+jFMTzPRSzy46dxNai0eErjTUVEldH1tOphzGMvKmOdm/nczH
4M/UOWOKBE1aOYZNPtnUgDy2MRt5K9VJStCNSHEQCB2lGdojNAtmj2cmr8flBN5m
gM9FDpIS1/C+OYYTkOY9ftPsH5zOk7sCLEHSH5USYRGJHihzLnkV90eiN6a7vlF1
hyTGrIyl6e//E5JBgamjnR3+fYuxQGr6WeAZEP/gXZRm7BCKCaPwCarq+kPZVG4A
nolZ/QQN6XYPSlveSPU97VYvLYEUvXaKN0Hf2DTbwkqvNFp7JORD65QLESPtQoIp
x95iHMdB/1+0OfgOqMmlOtKpOKREeQ/R+KWACxsrr5Rfv3/7CP4BMRGypIZ/iPmz
HWoyDI4lIebBR+JnjMjK
=4QFX
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.3 development
cycle.
Like with GPIO it's a lot of stuff. If my subsystems are any sign of
the overall tempo of the kernel v4.3 will be a gigantic diff.
[ It looks like 4.3 is calmer than 4.2 in most other subsystems, but
we'll see - Linus ]
Core changes:
- It is possible configure groups in debugfs.
- Consolidation of chained IRQ handler install/remove replacing all
call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a combined
call to irq_set_chained_handler_and_data(). This series was
created by Thomas Gleixner after the problem was observed by
Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which is
way cleaner.
- Tglx also wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs from
IRQ numbers. The goal is to get rid of the irq number from the
handlers in the IRQ flow which is nice.
Driver feature enhancements:
- Power management support for the SiRF SoC Atlas 7.
- Power down support for the Qualcomm driver.
- Intel Cherryview and Baytrail: switch drivers to use raw spinlocks
in IRQ handlers to play nice with the realtime patch set.
- Rework and new modes handling for Qualcomm SPMI-MPP.
- Pinconf power source config for SH PFC.
New drivers and subdrivers:
- A new driver for Conexant Digicolor CX92755.
- A new driver for UniPhier PH1-LD4, PH1-Pro4, PH1-sLD8, PH1-Pro5,
ProXtream2 and PH1-LD6b SoC pin control support.
- Reverse-egineered the S/PDIF settings for the Allwinner sun4i
driver.
- Support for Qualcomm Technologies QDF2xxx ARM64 SoCs
- A new Freescale i.mx6ul subdriver.
Cleanup:
- Remove platform data support in a number of SH PFC subdrivers"
* tag 'pinctrl-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (95 commits)
pinctrl: at91: fix null pointer dereference
pinctrl: mediatek: Implement wake handler and suspend resume
pinctrl: mediatek: Fix multiple registration issue.
pinctrl: sh-pfc: r8a7794: add USB pin groups
pinctrl: at91: Use generic irq_{request,release}_resources()
pinctrl: cherryview: Use raw_spinlock for locking
pinctrl: baytrail: Use raw_spinlock for locking
pinctrl: imx6ul: Remove .owner field
pinctrl: zynq: Fix typos in smc0_nand_grp and smc0_nor_grp
pinctrl: sh-pfc: Implement pinconf power-source param for voltage switching
clk: rockchip: add pclk_pd_pmu to the list of rk3288 critical clocks
pinctrl: sun4i: add spdif to pin description.
pinctrl: atlas7: clear ugly branch statements for pull and drivestrength
pinctrl: baytrail: Serialize all register access
pinctrl: baytrail: Drop FSF mailing address
pinctrl: rockchip: only enable gpio clock when it setting
pinctrl/mediatek: fix spelling mistake in dev_err error message
pinctrl: cherryview: Serialize all register access
pinctrl: UniPhier: PH1-Pro5: add I2C ch6 pin-mux setting
pinctrl: nomadik: reflect current input value
...
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc
versions of the descriptor calls that did not use the flags
argument on the end. This was around for too long and eventually
Uwe Kleine-König took the time to clean it out and the last
users are removed along with the macros in this tag. In several
cases the use of flags simplifies the code. For this reason we
have (ACKed) patches hitting in DRM, IIO, media, NFC, USB+PHY
up until we hammer in the nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff
we have i the kernel to discourage people from reinventing
a square wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO
IRQ chip instead of using one class for all chips, as the current
code will not work with systems with several GPIO chips doing
lockdep debugging.
- Protect against driver unloading also when a GPIO line is only
used as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent
device driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing
all call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a
combined call to irq_set_chained_handler_and_data(). This
series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which
is way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs
from IRQ numbers. The goal is to get rid of the irq number
from the handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO
drivers. This was an ARM specific function that is replaced
with the generic irq_modify_status() where special flags
are actually needed.
- When an OF node has a pin range for its GPIOs, return
-EPROBE_DEFER if the pin controller isn't available.
Pretty logical, yet needed to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own
irq_*_resources call back, then call these instead of the
defaults provided by the GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not
properly documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the
generic GPIO driver.
- Clean out platform data support from the Emma Mobile (EM)
driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver,
we now support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iQ2P
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.3 kernel cycle.
There is quite a lot going on in the GPIO subsystem this merge window,
so the main matter is decribed below.
The hits in other subsystems when making the GPIO flags optional are
all ACKed by their respective subsystem maintainers.
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc versions
of the descriptor calls that did not use the flags argument on the
end. This was around for too long and eventually Uwe Kleine-König
took the time to clean it out and the last users are removed along
with the macros in this tag. In several cases the use of flags
simplifies the code. For this reason we have (ACKed) patches
hitting in DRM, IIO, media, NFC, USB+PHY up until we hammer in the
nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff we
have i the kernel to discourage people from reinventing a square
wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO IRQ
chip instead of using one class for all chips, as the current code
will not work with systems with several GPIO chips doing lockdep
debugging.
- Protect against driver unloading also when a GPIO line is only used
as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent device
driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing all
call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a combined
call to irq_set_chained_handler_and_data().
This series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which is
way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs from
IRQ numbers. The goal is to get rid of the irq number from the
handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO drivers.
This was an ARM specific function that is replaced with the generic
irq_modify_status() where special flags are actually needed.
- When an OF node has a pin range for its GPIOs, return -EPROBE_DEFER
if the pin controller isn't available. Pretty logical, yet needed
to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own irq_*_resources call
back, then call these instead of the defaults provided by the
GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not properly
documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the generic
GPIO driver.
- Clean out platform data support from the Emma Mobile (EM) driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver, we now
support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver"
* tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
Revert "gpio: extraxfs: fix returnvar.cocci warnings"
gpio: tc3589x: use static container helper
gpio: xlp: fix error return code
gpio: vf610: handle level IRQ's properly
gpio: max732x: Fix error handling in probe()
gpio: omap: fix clk_prepare/unprepare usage
gpio: omap: protect regs access in omap_gpio_irq_handler
gpio: omap: fix omap2_set_gpio_debounce
gpio: omap: switch to use platform_get_irq
gpio: omap: remove wrong irq_domain_remove usage in probe
gpiolib: add description for gpio irqchip fields in struct gpio_chip
gpio: extraxfs: fix returnvar.cocci warnings
gpiolib: irqchip: use different lockdep class for each gpio irqchip
gpio/grgpio: fix deadlock in grgpio_irq_unmap()
Documentation: gpio: consumer: describe active low property
gpio: mxc: fix section mismatch warning
gpio/mxc: mask gpio interrupts in suspend
gpio: omap: Fix missing raw locks conversion
gpio: brcmstb: support wakeup from S5 cold boot
gpio: brcmstb: Add interrupt and wakeup source support
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.3 for MIPS. Here's the summary:
Three fixes that didn't make 4.2-stable:
- a -Os build might compile the kernel using the MIPS16 instruction
set but the R2 optimized inline functions in <uapi/asm/swab.h> are
implemented using 32-bit wide instructions which is invalid.
- a build error in pgtable-bits.h for a particular kernel
configuration.
- accessing registers of the CM GCR might have been compiled to use
64 bit accesses but these registers are onl 32 bit wide.
And also a few new bits:
- move the ATH79 GPIO driver to drivers/gpio
- the definition of IRQCHIP_DECLARE has moved to linux/irqchip.h,
change ATH79 accordingly.
- fix definition of pgprot_writecombine
- add an implementation of dma_map_ops.mmap
- fix alignment of quiet build output for vmlinuz link
- BCM47xx: Use kmemdup rather than duplicating its implementation
- Netlogic: Fix 0x0x prefixes of constants.
- merge Bjorn Helgaas' series to remove most of the weak keywords
from function declarations.
- CP0 and CP1 registers are best considered treated as unsigned
values to avoid large values from becoming negative values.
- improve support for the MIPS GIC timer.
- enable common clock framework for Malta and SEAD3.
- a number of improvments and fixes to dump_tlb().
- document the MIPS TLB dump functionality in Magic SysRq.
- Cavium Octeon CN68XX improvments.
- NetLogic improvments.
- irq: Use access helper irq_data_get_affinity_mask.
- handle MSA unaligned accesses.
- a number of R6-related math-emu fixes.
- support for I6400.
- improvments to MSA support.
- add uprobes support.
- move from deprecated __initcall to arch_initcall.
- remove finish_arch_switch().
- IRQ cleanups by Thomas Gleixner.
- migrate to new 'set-state' interface.
- random small cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (148 commits)
MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16.
MIPS: Fix alignment of quiet build output for vmlinuz link
MIPS: math-emu: Remove unused handle_dsemul function declaration
MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 CLASS FPU instruction
MIPS: math-emu: Add support for the MIPS R6 RINT FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELNEZ FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELEQZ FPU instruction
MIPS: math-emu: Add support for the CMP.condn.fmt R6 instruction
MIPS: inst.h: Add new MIPS R6 FPU opcodes
MIPS: Octeon: Fix management port MII address on Kontron S1901
MIPS: BCM47xx: Use kmemdup rather than duplicating its implementation
STAGING: Octeon: Use common helpers for determining interface and port
MIPS: Octeon: Support interfaces 4 and 5
MIPS: Octeon: Set up 1:1 mapping between CN68XX PKO queues and ports
MIPS: Octeon: Initialize CN68XX PKO
STAGING: Octeon: Support CN68XX style WQE
...
- Support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- Introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- Use hardware RNG for arch_get_random_seed_* not arch_get_random_* from Paul Mackerras
- Seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh Salgaonkar
- Add powerpc timebase as a trace clock source from Naveen N. Rao
- Misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- Add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- Fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- Drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from Andrew Donnellan
- Initialize distance lookup table from drconf path from Nikunj A Dadhania
- Enable RTC class support from Vaibhav Jain
- Disable automatically blocked PCI config from Gavin Shan
- Add LEDs driver for PowerNV platform from Vasant Hegde
- Fix endianness issues in the HVSI driver from Laurent Dufour
- Kexec endian fixes from Samuel Mendoza-Jonas
- Fix corrupted pdn list from Gavin Shan
- Fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and updates,
device tree updates, e6500 fixes for non-SMP, and misc cleanup and minor
fixes.
- A ton of cxl updates & fixes:
- Add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- Destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- Destroy afu->contexts_idr on release of an afu from Johannes Thumshirn
- Compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- Plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- Add alternate MMIO error handling from Ian Munsie
- Allow release of contexts which have been OPENED but not STARTED from Andrew Donnellan
- Remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- Release irqs if memory allocation fails from Vaibhav Jain
- Remove racy attempt to force EEH invocation in reset from Daniel Axtens
- Fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- Fix force unmapping mmaps of contexts allocated through the kernel api from Ian Munsie
- Set up and enable PSL Timebase from Philippe Bergheaud
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=n9+X
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask
from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- use hardware RNG for arch_get_random_seed_* not arch_get_random_*
from Paul Mackerras
- seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh
Salgaonkar
- add powerpc timebase as a trace clock source from Naveen N. Rao
- misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from
Andrew Donnellan
- initialize distance lookup table from drconf path from Nikunj A
Dadhania
- enable RTC class support from Vaibhav Jain
- disable automatically blocked PCI config from Gavin Shan
- add LEDs driver for PowerNV platform from Vasant Hegde
- fix endianness issues in the HVSI driver from Laurent Dufour
- kexec endian fixes from Samuel Mendoza-Jonas
- fix corrupted pdn list from Gavin Shan
- fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and
updates, device tree updates, e6500 fixes for non-SMP, and misc
cleanup and minor fixes.
- a ton of cxl updates & fixes:
- add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- destroy afu->contexts_idr on release of an afu from Johannes
Thumshirn
- compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- add alternate MMIO error handling from Ian Munsie
- allow release of contexts which have been OPENED but not STARTED
from Andrew Donnellan
- remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- release irqs if memory allocation fails from Vaibhav Jain
- remove racy attempt to force EEH invocation in reset from Daniel
Axtens
- fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- fix force unmapping mmaps of contexts allocated through the kernel
api from Ian Munsie
- set up and enable PSL Timebase from Philippe Bergheaud
* tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (140 commits)
cxl: Set up and enable PSL Timebase
cxl: Fix force unmapping mmaps of contexts allocated through the kernel api
cxl: Fix + cleanup error paths in cxl_dev_context_init
powerpc/eeh: Fix fenced PHB caused by eeh_slot_error_detail()
powerpc/pseries: Cleanup on pci_dn_reconfig_notifier()
powerpc/pseries: Fix corrupted pdn list
powerpc/powernv: Enable LEDS support
powerpc/iommu: Set default DMA offset in dma_dev_setup
cxl: Remove racy attempt to force EEH invocation in reset
cxl: Release irqs if memory allocation fails
cxl: Remove use of macro DEFINE_PCI_DEVICE_TABLE
powerpc/powernv: Fix mis-merge of OPAL support for LEDS driver
powerpc/powernv: Reset HILE before kexec_sequence()
powerpc/kexec: Reset secondary cpu endianness before kexec
powerpc/hvsi: Fix endianness issues in the HVSI driver
leds/powernv: Add driver for PowerNV platform
powerpc/powernv: Create LED platform device
powerpc/powernv: Add OPAL interfaces for accessing and modifying system LED states
powerpc/powernv: Fix the log message when disabling VF
cxl: Allow release of contexts which have been OPENED but not STARTED
...
Pull ARM development updates from Russell King:
"Included in this update:
- moving PSCI code from ARM64/ARM to drivers/
- removal of some architecture internals from global kernel view
- addition of software based "privileged no access" support using the
old domains register to turn off the ability for kernel
loads/stores to access userspace. Only the proper accessors will
be usable.
- addition of early fixup support for early console
- re-addition (and reimplementation) of OMAP special interconnect
barrier
- removal of finish_arch_switch()
- only expose cpuX/online in sysfs if hotpluggable
- a number of code cleanups"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (41 commits)
ARM: software-based priviledged-no-access support
ARM: entry: provide uaccess assembly macro hooks
ARM: entry: get rid of multiple macro definitions
ARM: 8421/1: smp: Collapse arch_cpu_idle_dead() into cpu_die()
ARM: uaccess: provide uaccess_save_and_enable() and uaccess_restore()
ARM: mm: improve do_ldrd_abort macro
ARM: entry: ensure that IRQs are enabled when calling syscall_trace_exit()
ARM: entry: efficiency cleanups
ARM: entry: get rid of asm_trace_hardirqs_on_cond
ARM: uaccess: simplify user access assembly
ARM: domains: remove DOMAIN_TABLE
ARM: domains: keep vectors in separate domain
ARM: domains: get rid of manager mode for user domain
ARM: domains: move initial domain setting value to asm/domains.h
ARM: domains: provide domain_mask()
ARM: domains: switch to keeping domain value in register
ARM: 8419/1: dma-mapping: harmonize definition of DMA_ERROR_CODE
ARM: 8417/1: refactor bitops functions with BIT_MASK() and BIT_WORD()
ARM: 8416/1: Feroceon: use of_iomap() to map register base
ARM: 8415/1: early fixmap support for earlycon
...
Pull networking updates from David Miller:
"Another merge window, another set of networking changes. I've heard
rumblings that the lightweight tunnels infrastructure has been voted
networking change of the year. But what do I know?
1) Add conntrack support to openvswitch, from Joe Stringer.
2) Initial support for VRF (Virtual Routing and Forwarding), which
allows the segmentation of routing paths without using multiple
devices. There are some semantic kinks to work out still, but
this is a reasonably strong foundation. From David Ahern.
3) Remove spinlock fro act_bpf fast path, from Alexei Starovoitov.
4) Ignore route nexthops with a link down state in ipv6, just like
ipv4. From Andy Gospodarek.
5) Remove spinlock from fast path of act_gact and act_mirred, from
Eric Dumazet.
6) Document the DSA layer, from Florian Fainelli.
7) Add netconsole support to bcmgenet, systemport, and DSA. Also
from Florian Fainelli.
8) Add Mellanox Switch Driver and core infrastructure, from Jiri
Pirko.
9) Add support for "light weight tunnels", which allow for
encapsulation and decapsulation without bearing the overhead of a
full blown netdevice. From Thomas Graf, Jiri Benc, and a cast of
others.
10) Add Identifier Locator Addressing support for ipv6, from Tom
Herbert.
11) Support fragmented SKBs in iwlwifi, from Johannes Berg.
12) Allow perf PMUs to be accessed from eBPF programs, from Kaixu Xia.
13) Add BQL support to 3c59x driver, from Loganaden Velvindron.
14) Stop using a zero TX queue length to mean that a device shouldn't
have a qdisc attached, use an explicit flag instead. From Phil
Sutter.
15) Use generic geneve netdevice infrastructure in openvswitch, from
Pravin B Shelar.
16) Add infrastructure to avoid re-forwarding a packet in software
that was already forwarded by a hardware switch. From Scott
Feldman.
17) Allow AF_PACKET fanout function to be implemented in a bpf
program, from Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1458 commits)
netfilter: nf_conntrack: make nf_ct_zone_dflt built-in
netfilter: nf_dup{4, 6}: fix build error when nf_conntrack disabled
net: fec: clear receive interrupts before processing a packet
ipv6: fix exthdrs offload registration in out_rt path
xen-netback: add support for multicast control
bgmac: Update fixed_phy_register()
sock, diag: fix panic in sock_diag_put_filterinfo
flow_dissector: Use 'const' where possible.
flow_dissector: Fix function argument ordering dependency
ixgbe: Resolve "initialized field overwritten" warnings
ixgbe: Remove bimodal SR-IOV disabling
ixgbe: Add support for reporting 2.5G link speed
ixgbe: fix bounds checking in ixgbe_setup_tc for 82598
ixgbe: support for ethtool set_rxfh
ixgbe: Avoid needless PHY access on copper phys
ixgbe: cleanup to use cached mask value
ixgbe: Remove second instance of lan_id variable
ixgbe: use kzalloc for allocating one thing
flow: Move __get_hash_from_flowi{4,6} into flow_dissector.c
ixgbe: Remove unused PCI bus types
...
SPI NOR
* reduce virtual address space requirements for fsl-quadspi memory map
* new fsl-quadspi IP support: imx6ul-qspi and imx7d-qspi
* add new NOR flash device support
* add new driver for NXP SPI Flash Interface (SPIFI)
* stop abusing SPI API structs for non-SPI framework
* fixup DT table matching for new "jedec,spi-nor" string
NAND
* brcmnand: fix big endian MIPS macro usage
* denali: refactor to use devres, dev_*() printing, etc.
* OMAP ELM: change the module alias to actually be usable
* pxa3xx_nand: fixup a few command sequencing issues -- both new and old
- race conditions in the IRQ handler status clearing
- problems when a bootloader left interrupts pending
- config issues when overriding the bootloader configuration
* new flash device support
* sunxi_nand:
- optimize timing configuration by calculation, rather than fixed
fail-safe values
- use EDO setting from ONFI
* r852: fix compiler warnings
* davinci: add 4KB page support
Core
* oobtest: correct debug print information
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vpBS
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20150901' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"SPI NOR:
- reduce virtual address space requirements for fsl-quadspi memory map
- new fsl-quadspi IP support: imx6ul-qspi and imx7d-qspi
- add new NOR flash device support
- add new driver for NXP SPI Flash Interface (SPIFI)
- stop abusing SPI API structs for non-SPI framework
- fixup DT table matching for new "jedec,spi-nor" string
NAND:
- brcmnand: fix big endian MIPS macro usage
- denali: refactor to use devres, dev_*() printing, etc.
- OMAP ELM: change the module alias to actually be usable
- pxa3xx_nand: fixup a few command sequencing issues -- both new and old
- race conditions in the IRQ handler status clearing
- problems when a bootloader left interrupts pending
- config issues when overriding the bootloader configuration
- new flash device support
- sunxi_nand:
- optimize timing configuration by calculation, rather than fixed
fail-safe values
- use EDO setting from ONFI
- r852: fix compiler warnings
- davinci: add 4KB page support
Core:
- oobtest: correct debug print information"
* tag 'for-linus-20150901' of git://git.infradead.org/linux-mtd: (42 commits)
mtd: mtd_oobtest: Fix the address offset with vary_offset case
mtd: blkdevs: fix switch-bool compilation warning
mtd: spi-nor: stop (ab)using struct spi_device_id
mtd: nand: add Toshiba TC58NVG0S3E to nand_ids table
mtd: dataflash: Export OF module alias information
nand: pxa3xx: Increase READ_ID buffer and make the size static
mtd: nand: pxa3xx-nand: fix random command timeouts
mtd: nand: pxa3xx_nand: fix early spurious interrupt
mtd: pxa3xx_nand: add a default chunk size
mtd: omap_elm: Fix module alias
mtd: physmap_of: fix null pointer deference when kzalloc returns null
mtd: nettel: do not ignore mtd_device_register() failure in nettel_init()
mtd: denali_pci: switch to dev_err()
mtd: denali_pci: refactor driver using devres API
mtd: denali_pci: use module_pci_driver() macro
mtd: denali: hide core part from user in Kconfig
mtd: spi-nor: add Spansion S25FL204K support
mtd: spi-nor: Improve Kconfig help text for SPI_FSL_QUADSPI
mtd: spi-nor: add driver for NXP SPI Flash Interface (SPIFI)
doc: dt: add documentation for nxp,lpc1773-spifi
...
- ACPICA update to upstream revision 20150818 including method
tracing extensions to allow more in-depth AML debugging in the
kernel and a number of assorted fixes and cleanups (Bob Moore,
Lv Zheng, Markus Elfring).
- ACPI sysfs code updates and a documentation update related to
AML method tracing (Lv Zheng).
- ACPI EC driver fix related to serialized evaluations of _Qxx
methods and ACPI tools updates allowing the EC userspace tool
to be built from the kernel source (Lv Zheng).
- ACPI processor driver updates preparing it for future
introduction of CPPC support and ACPI PCC mailbox driver
updates (Ashwin Chaugule).
- ACPI interrupts enumeration fix for a regression related
to the handling of IRQ attribute conflicts between MADT
and the ACPI namespace (Jiang Liu).
- Fixes related to ACPI device PM (Mika Westerberg, Srinidhi Kasagar).
- ACPI device registration code reorganization to separate the
sysfs-related code and bus type operations from the rest (Rafael
J Wysocki).
- Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).
- ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups
(Pan Xinhui, Rafael J Wysocki).
- cpufreq core cleanups on top of the previous changes allowing it
to preseve its sysfs directories over system suspend/resume (Viresh
Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).
- cpufreq fixes and cleanups related to governors (Viresh Kumar).
- cpufreq updates (core and the cpufreq-dt driver) related to the
turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).
- New DT bindings for Operating Performance Points (OPP), support
for them in the OPP framework and in the cpufreq-dt driver plus
related OPP framework fixes and cleanups (Viresh Kumar).
- cpufreq powernv driver updates (Shilpasri G Bhat).
- New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).
- Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).
- intel_pstate driver updates including Skylake-S support, support
for enabling HW P-states per CPU and an additional vendor bypass
list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).
- cpuidle core fixes related to the handling of coupled idle states
(Xunlei Pang).
- intel_idle driver updates including Skylake Client support and
support for freeze-mode-specific idle states (Len Brown).
- Driver core updates related to power management (Andy Shevchenko,
Rafael J Wysocki).
- Generic power domains framework fixes and cleanups (Jon Hunter,
Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).
- Device PM QoS framework update to allow the latency tolerance
setting to be exposed to user space via sysfs (Mika Westerberg).
- devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).
- System sleep support updates (Alan Stern, Len Brown, SungEun Kim).
- rockchip-io AVS support updates (Heiko Stuebner).
- PM core clocks support fixup (Colin Ian King).
- Power capping RAPL driver update including support for Skylake H/S
and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).
- Generic device properties framework fixes related to the handling
of static (driver-provided) property sets (Andy Shevchenko).
- turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
Shreyas B Prabhu).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=fTgI
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"From the number of commits perspective, the biggest items are ACPICA
and cpufreq changes with the latter taking the lead (over 50 commits).
On the cpufreq front, there are many cleanups and minor fixes in the
core and governors, driver updates etc. We also have a new cpufreq
driver for Mediatek MT8173 chips.
ACPICA mostly updates its debug infrastructure and adds a number of
fixes and cleanups for a good measure.
The Operating Performance Points (OPP) framework is updated with new
DT bindings and support for them among other things.
We have a few updates of the generic power domains framework and a
reorganization of the ACPI device enumeration code and bus type
operations.
And a lot of fixes and cleanups all over.
Included is one branch from the MFD tree as it contains some
PM-related driver core and ACPI PM changes a few other commits are
based on.
Specifics:
- ACPICA update to upstream revision 20150818 including method
tracing extensions to allow more in-depth AML debugging in the
kernel and a number of assorted fixes and cleanups (Bob Moore, Lv
Zheng, Markus Elfring).
- ACPI sysfs code updates and a documentation update related to AML
method tracing (Lv Zheng).
- ACPI EC driver fix related to serialized evaluations of _Qxx
methods and ACPI tools updates allowing the EC userspace tool to be
built from the kernel source (Lv Zheng).
- ACPI processor driver updates preparing it for future introduction
of CPPC support and ACPI PCC mailbox driver updates (Ashwin
Chaugule).
- ACPI interrupts enumeration fix for a regression related to the
handling of IRQ attribute conflicts between MADT and the ACPI
namespace (Jiang Liu).
- Fixes related to ACPI device PM (Mika Westerberg, Srinidhi
Kasagar).
- ACPI device registration code reorganization to separate the
sysfs-related code and bus type operations from the rest (Rafael J
Wysocki).
- Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).
- ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups (Pan
Xinhui, Rafael J Wysocki).
- cpufreq core cleanups on top of the previous changes allowing it to
preseve its sysfs directories over system suspend/resume (Viresh
Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).
- cpufreq fixes and cleanups related to governors (Viresh Kumar).
- cpufreq updates (core and the cpufreq-dt driver) related to the
turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).
- New DT bindings for Operating Performance Points (OPP), support for
them in the OPP framework and in the cpufreq-dt driver plus related
OPP framework fixes and cleanups (Viresh Kumar).
- cpufreq powernv driver updates (Shilpasri G Bhat).
- New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).
- Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).
- intel_pstate driver updates including Skylake-S support, support
for enabling HW P-states per CPU and an additional vendor bypass
list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).
- cpuidle core fixes related to the handling of coupled idle states
(Xunlei Pang).
- intel_idle driver updates including Skylake Client support and
support for freeze-mode-specific idle states (Len Brown).
- Driver core updates related to power management (Andy Shevchenko,
Rafael J Wysocki).
- Generic power domains framework fixes and cleanups (Jon Hunter,
Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).
- Device PM QoS framework update to allow the latency tolerance
setting to be exposed to user space via sysfs (Mika Westerberg).
- devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).
- System sleep support updates (Alan Stern, Len Brown, SungEun Kim).
- rockchip-io AVS support updates (Heiko Stuebner).
- PM core clocks support fixup (Colin Ian King).
- Power capping RAPL driver update including support for Skylake H/S
and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).
- Generic device properties framework fixes related to the handling
of static (driver-provided) property sets (Andy Shevchenko).
- turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
Shreyas B Prabhu)"
* tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (180 commits)
cpufreq: speedstep-lib: Use monotonic clock
cpufreq: powernv: Increase the verbosity of OCC console messages
cpufreq: sfi: use kmemdup rather than duplicating its implementation
cpufreq: drop !cpufreq_driver check from cpufreq_parse_governor()
cpufreq: rename cpufreq_real_policy as cpufreq_user_policy
cpufreq: remove redundant 'policy' field from user_policy
cpufreq: remove redundant 'governor' field from user_policy
cpufreq: update user_policy.* on success
cpufreq: use memcpy() to copy policy
cpufreq: remove redundant CPUFREQ_INCOMPATIBLE notifier event
cpufreq: mediatek: Add MT8173 cpufreq driver
dt-bindings: mediatek: Add MT8173 CPU DVFS clock bindings
PM / Domains: Fix typo in description of genpd_dev_pm_detach()
PM / Domains: Remove unusable governor dummies
PM / Domains: Make pm_genpd_init() available to modules
PM / domains: Align column headers and data in pm_genpd_summary output
powercap / RAPL: disable the 2nd power limit properly
tools: cpupower: Fix error when running cpupower monitor
PM / OPP: Drop unlikely before IS_ERR(_OR_NULL)
PM / OPP: Fix static checker warning (broken 64bit big endian systems)
...
- Adding Frank Rowand as DT maintainer in preparation for Grant's
retirement.
- Generic MSI binding documentation and a few other minor doc updates
- Fix long standing issue with DT platorm device unregistration
- Fix loop forever bug in of_find_matching_node_by_address()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV5hAQAAoJEMhvYp4jgsXiguMIAJippY6yiqatAQr2TcWktkUx
KiN209DxPCoAFz9EeCyJ+ck0BV6xKSQf1x/ef93kynYXlQ2uWOWXW6guH8rQ5XFN
15aovQnd03PVcpzsMOSVi/ZxtyGJflxO+RBrcrJ0Vy2HaAYsMmfCiYdLAnhMmJnz
Wr4W1LfYLTxchNIS1LlBUKRAeZyOx47yRVEXfNqfjbCu+bJgXDtMj7NNH3muXqVf
WZIJu0XFb6UIgMPB/jDdC0Ln6FGe01HIDKQ/EpGgBm/flfSsywVH6eB06R7+EHym
T6ap5pRQHXB+oxRU8bGo88Z7xEbcBhKckRT/zvs/vPuG/DfWluIVxbJpR4htJ84=
=zTPm
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- added Frank Rowand as DT maintainer in preparation for Grant's
retirement.
- generic MSI binding documentation and a few other minor doc updates
- fix long standing issue with DT platorm device unregistration
- fix loop forever bug in of_find_matching_node_by_address()
* tag 'devicetree-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
MAINTAINERS: Add Frank Rowand as DT maintainer
mtd: nand: pxa3xx: add optional dma for pxa architecture
Documentation: DT: cpsw: document missing compatible
Docs: dt: add generic MSI bindings
drivercore: Fix unregistration path of platform devices
of/address: Don't loop forever in of_find_matching_node_by_address().
of: Add vendor prefix for JEDEC Solid State Technology Association
of/platform: add function to populate default bus
of: Add vendor prefix for Sharp Corporation
Pull irq updates from Thomas Gleixner:
"This updated pull request does not contain the last few GIC related
patches which were reported to cause a regression. There is a fix
available, but I let it breed for a couple of days first.
The irq departement provides:
- new infrastructure to support non PCI based MSI interrupts
- a couple of new irq chip drivers
- the usual pile of fixlets and updates to irq chip drivers
- preparatory changes for removal of the irq argument from interrupt
flow handlers
- preparatory changes to remove IRQF_VALID"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources
irqchip: Add bcm2836 interrupt controller for Raspberry Pi 2
irqchip: Add documentation for the bcm2836 interrupt controller
irqchip/bcm2835: Add support for being used as a second level controller
irqchip/bcm2835: Refactor handle_IRQ() calls out of MAKE_HWIRQ
PCI: xilinx: Fix typo in function name
irqchip/gic: Ensure gic_cpu_if_up/down() programs correct GIC instance
irqchip/gic: Only allow the primary GIC to set the CPU map
PCI/MSI: pci-xgene-msi: Consolidate chained IRQ handler install/remove
unicore32/irq: Prepare puv3_gpio_handler for irq argument removal
tile/pci_gx: Prepare trio_handle_level_irq for irq argument removal
m68k/irq: Prepare irq handlers for irq argument removal
C6X/megamode-pic: Prepare megamod_irq_cascade for irq argument removal
blackfin: Prepare irq handlers for irq argument removal
arc/irq: Prepare idu_cascade_isr for irq argument removal
sparc/irq: Use access helper irq_data_get_affinity_mask()
sparc/irq: Use helper irq_data_get_irq_handler_data()
parisc/irq: Use access helper irq_data_get_affinity_mask()
mn10300/irq: Use access helper irq_data_get_affinity_mask()
irqchip/i8259: Prepare i8259_irq_dispatch for irq argument removal
...
Here's our branch of ARM64 contents for this merge window.
Most of this is DT contents for new SoCs (or those who have seen new
device support added). Maybe we should stop separating out the arm64
contents here to avoid the kind of internal conflicts as we got this
time around, where 32- and 64-bit contents conflicted.
Anyhow, on the actual contents:
New SoCs:
- Broadcom North Star 2 (ns2)
- Marvell Berlin4CT
- Mediatek MT6795
- Rockchip RK3368
In addition, there are enhancements for the following platforms:
- Mediatek MT8173: cpuidle-dt updates, misc other additions
- ZyncMP: A bunch of devices added to the existing DTSI
- Qualcomm MSM8916 and APQ8016 updates for USB, etc.
+ A handful of other updates for various platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SZR9
-----END PGP SIGNATURE-----
Merge tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit changes from Olof Johansson:
"Here's our branch of ARM64 contents for this merge window.
Most of this is DT contents for new SoCs (or those who have seen new
device support added). Maybe we should stop separating out the arm64
contents here to avoid the kind of internal conflicts as we got this
time around, where 32- and 64-bit contents conflicted.
Anyhow, on the actual contents:
New SoCs:
- Broadcom North Star 2 (ns2)
- Marvell Berlin4CT
- Mediatek MT6795
- Rockchip RK3368
In addition, there are enhancements for the following platforms:
- Mediatek MT8173: cpuidle-dt updates, misc other additions
- ZyncMP: A bunch of devices added to the existing DTSI
- Qualcomm MSM8916 and APQ8016 updates for USB, etc.
+ a handful of other updates for various platforms"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (47 commits)
ARM64: dts: vexpress: Use assigned-clock-parents for sp810
ARM64: dts: mt6795: enable basic SMP bringup for MT6795
arm64: Enable Marvell Berlin SoC family in defconfig
arm64: Enable Marvell Berlin SoC family in Kconfig
arm64: dts: Add dts files for Marvell Berlin4CT SoC
ARM64: zynqmp: Move SPI nodes to the right location
ARM64: zynqmp: Move uart and ttcs to the right location
ARM64: zynqmp: Enable spi flashes on ep108
ARM64: zynqmp: Add eeprom memories on i2c bus
ARM64: zynqmp: Enable sdhci on ep108
ARM64: zynqmp: Enable watchdog on ep108
ARM64: zynqmp: Add DWC3 usb support
ARM64: zynqmp: Add SMMU support
ARM64: zynqmp: Add CANs node for platform
ARM64: zynqmp: Use zynqmp specific compatible string for gpio
devicetree: xilinx: zynqmp: add sata node
PCI: iproc: Fix BCMA dependency in Kconfig
arm64: dts: Add Broadcom North Star 2 support
arm64: Add Broadcom iProc family support
PCI: iproc: Fix ARM64 dependency in Kconfig
...
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- Cleanups for Renesas shmobile platforms
- Lots of added devices on LPC18xx
- Lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some branches
that are primarily merged through the clock tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=D2Pm
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Ladies and gentlemen, we proudly announce to you the latest branch of
ARM device tree contents for the mainline kernel. Come and see, come
and see!
No less than twentythree thousand lines of additions! Just imagine the
joy you will have of using your mainline kernel on newly supported
hardware such as Rockchip Chromebooks, Freescale i.MX6UL boards or
UniPhier hardware!
For those of you feeling less adventurous, added hardware support on
platforms such as TI DM814x and Gumstix Overo platforms might be more
of your liking.
We've got something for everyone here!
Ahem. Cough. So, anyway...
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- cleanups for Renesas shmobile platforms
- lots of added devices on LPC18xx
- lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some
branches that are primarily merged through the clock tree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (389 commits)
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
ARM: dts: zynq: Add devicetree entry for Xilinx Zynq reset controller.
ARM: dts: UniPhier: fix PPI interrupt CPU mask of timer nodes
ARM: dts: rockchip: correct regulator power states for suspend
ARM: dts: rockchip: correct regulator PM properties
ARM: dts: vexpress: Use assigned-clock-parents for sp810
pinctrl: tegra: Only set the gpio range if needed
arm: boot: dts: am4372: add ARM timers and SCU nodes
ARM: dts: AM4372: Add the am4372-rtc compatible string
ARM: shmobile: r8a7794 dtsi: Add CPG/MSTP Clock Domain
ARM: shmobile: r8a7793 dtsi: Add CPG/MSTP Clock Domain
...
Some releases this branch is nearly empty, others we have more stuff. It
tends to gather drivers that need SoC modification or dependencies such
that they have to (also) go in through our tree.
For this release, we have merged in part of the reset controller tree
(with handshake that the parts we have merged in will remain stable),
as well as dependencies on a few clock branches.
In general, new items here are:
- Qualcomm driver for SMM/SMD, which is how they communicate with the
coprocessors on (some) of their platforms
- Memory controller work for ARM's PL172 memory controller
- Reset drivers for various platforms
- PMU power domain support for Marvell platforms
- Tegra support for T132/T210 SoCs: PMC, fuse, memory controller per-SoC support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=B6jn
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Some releases this branch is nearly empty, others we have more stuff.
It tends to gather drivers that need SoC modification or dependencies
such that they have to (also) go in through our tree.
For this release, we have merged in part of the reset controller tree
(with handshake that the parts we have merged in will remain stable),
as well as dependencies on a few clock branches.
In general, new items here are:
- Qualcomm driver for SMM/SMD, which is how they communicate with the
coprocessors on (some) of their platforms
- memory controller work for ARM's PL172 memory controller
- reset drivers for various platforms
- PMU power domain support for Marvell platforms
- Tegra support for T132/T210 SoCs: PMC, fuse, memory controller
per-SoC support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits)
ARM: tegra: cpuidle: implement cpuidle_state.enter_freeze()
ARM: tegra: Disable cpuidle if PSCI is available
soc/tegra: pmc: Use existing pclk reference
soc/tegra: pmc: Remove unnecessary return statement
soc: tegra: Remove redundant $(CONFIG_ARCH_TEGRA) in Makefile
memory: tegra: Add Tegra210 support
memory: tegra: Add support for a variable-size client ID bitfield
clk: shmobile: rz: Add CPG/MSTP Clock Domain support
clk: shmobile: rcar-gen2: Add CPG/MSTP Clock Domain support
clk: shmobile: r8a7779: Add CPG/MSTP Clock Domain support
clk: shmobile: r8a7778: Add CPG/MSTP Clock Domain support
clk: shmobile: Add CPG/MSTP Clock Domain support
ARM: dove: create a proper PMU driver for power domains, PMU IRQs and resets
reset: reset-zynq: Adding support for Xilinx Zynq reset controller.
docs: dts: Added documentation for Xilinx Zynq Reset Controller bindings.
MIPS: ath79: Add the reset controller to the AR9132 dtsi
reset: Add a driver for the reset controller on the AR71XX/AR9XXX
devicetree: Add bindings for the ATH79 reset controller
reset: socfpga: Update reset-socfpga to read the altr,modrst-offset property
doc: dt: add documentation for lpc1850-rgu reset driver
...
New or improved SoC support:
- Addition of support for Atmel's SAMA5D2 SoC
- Addition of Freescale i.MX6UL
- Improved support of TI's DM814x platform
- Misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch are
also here (acked by appropriate maintainers):
- Power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- Clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJV5Mo6AAoJEIwa5zzehBx3VnMP/28LFJVUjIbd2xjJBo2gbSwV
jN7uGlTkKU+1kHjZqnUPuirlBxBzsXKgRfBvCoeu0cPOggwmFcaF915/HHPz7xuz
vTP7k98+Y5nSXScIohWkWCdZTpKKjve4sn74rXmiNakTUiuaHf5lKut/m7ldVrWd
hN1o9W4LN+5O1mOYbc9ZD98v3bkDb6eu+a22oK7qemXiEiQi+NIMoDx+IR2bd4pA
FeDaW7sOFWTEYU/p+M5nZNvI3n53P0/mlB5rPRiAYRjhQf9DrWHm5G7HdnMkUkgo
/s8/QlVjBkJwhkY0TqpwtHY23JjSSB6UtCnXzb1eVAkX1nJN6PJQpcpCz1zJhd9q
+sJ2k1zEvrfomJCK7/iZ1ubQE09KlJLEeb8xi5xCwD0MBOBAYC31bovDVAswCitV
8NHnfltEG+wCMyX955eqqGkVxkcw8sJMJUK5A95aK6w+vKqjd7gUgLJjXFC1u4eN
ECuVVUf1hVmUEmM799CDayTlfGDt4oGLmHGao+SiSCVc1XbG9HkWr7Lcgr6u9UHr
lNv3RIe6Axb85xxIU0/9hqLHrtB85uEQjjlbnQx3o7u8RsSOeaiZvCz4BzcjP9E1
VGyD6zkRWhuDiMFlPVXiAX0qIH5xSjIWkC0wPNJNy8eWFH9tkfGL0mOlLbl09oGR
gtuvOrjbF/BhILkPw38y
=8T5Z
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New or improved SoC support:
- add support for Atmel's SAMA5D2 SoC
- add support for Freescale i.MX6UL
- improved support for TI's DM814x platform
- misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch
are also here (acked by appropriate maintainers):
- power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: rockchip: pm: Fix PTR_ERR() argument
ARM: imx: mach-imx6ul: Fix allmodconfig build
clk: ti: fix for definition movement
ARM: uniphier: drop v7_invalidate_l1 call at secondary entry
memory: kill off set_irq_flags usage
rtc: snvs: select option REGMAP_MMIO
ARM: brcmstb: select ARCH_DMA_ADDR_T_64BIT for LPAE
ARM: BCM: Enable ARM erratum 798181 for BRCMSTB
ARM: OMAP2+: Fix power domain operations regression caused by 81xx
ARM: rockchip: enable PMU_GPIOINT_WAKEUP_EN when entering shallow suspend
ARM: rockchip: set correct stabilization thresholds in suspend
ARM: rockchip: rename osc_switch_to_32k variable
ARM: imx6ul: add fec MAC refrence clock and phy fixup init
ARM: imx6ul: add fec bits to GPR syscon definition
rtc: mxc: add support of device tree
dt-binding: document the binding for mxc rtc
rtc: mxc: use a second rtc clock
ARM: davinci: cp_intc: use IRQCHIP_SKIP_SET_WAKE instead of irq_set_wake callback
soc: mediatek: Fix SCPSYS compilation
ARM: at91/soc: add basic support for new sama5d2 SoC
...
A large cleanup branch this release, with a healthy 10k negative line delta.
Most of this is removal of legacy (non-DT) support of shmobile
platforms. There is also removal of two non-DT platforms on OMAP,
and the plat-samsung directory is cleaned out by moving most of the
previously shared-location-but-not-actually-shared files from there to
the appropriate mach directories instead.
There are other sets of changes in here as well:
- Rob Herring removed use of set_irq_flags under all platforms and
moved to genirq alternatives
- A series of timer API conversions to set-state interface
- ep93xx, nomadik and ux500 cleanups from Linus Walleij
- __init annotation fixes from Nicolas Pitre
+ a bunch of other changes that all add up to a nice set of cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=acy4
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"A large cleanup branch this release, with a healthy 10k negative line
delta.
Most of this is removal of legacy (non-DT) support of shmobile
platforms. There is also removal of two non-DT platforms on OMAP, and
the plat-samsung directory is cleaned out by moving most of the
previously shared-location-but-not-actually-shared files from there to
the appropriate mach directories instead.
There are other sets of changes in here as well:
- Rob Herring removed use of set_irq_flags under all platforms and
moved to genirq alternatives
- a series of timer API conversions to set-state interface
- ep93xx, nomadik and ux500 cleanups from Linus Walleij
- __init annotation fixes from Nicolas Pitre
+ a bunch of other changes that all add up to a nice set of cleanups"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (108 commits)
ARM/fb: ep93xx: switch framebuffer to use modedb only
ARM: gemini: Setup timer3 as free running timer
ARM: gemini: Use timer1 for clockevent
ARM: gemini: Add missing register definitions for gemini timer
ARM: ep93xx/timer: Migrate to new 'set-state' interface
ARM: nomadik: push accelerometer down to boards
ARM: nomadik: move l2x0 setup to device tree
ARM: nomadik: selectively enable UART0 on boards
ARM: nomadik: move hog code to use DT hogs
ARM: shmobile: Fix mismerges
ARM: ux500: simplify secondary CPU boot
ARM: SAMSUNG: remove keypad-core header in plat-samsung
ARM: SAMSUNG: local watchdog-reset header in mach-s3c64xx
ARM: SAMSUNG: local onenand-core header in mach-s3c64xx
ARM: SAMSUNG: local irq-uart header in mach-s3c64xx
ARM: SAMSUNG: local backlight header in mach-s3c64xx
ARM: SAMSUNG: local ata-core header in mach-s3c64xx
ARM: SAMSUNG: local regs-usb-hsotg-phy header in mach-s3c64xx
ARM: SAMSUNG: local spi-core header in mach-s3c24xx
ARM: SAMSUNG: local nand-core header in mach-s3c24xx
...
-perf support for ARCv2 based cores (sampling interrupt, SMP)
-leftovers for ARCv2 support
-Futex fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wem3
-----END PGP SIGNATURE-----
Merge tag 'arc-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC architecture updates from Vineet Gupta:
"ARC updates for 4.3:
- perf support for ARCv2 based cores (sampling interrupt, SMP)
- leftovers for ARCv2 support
- futex fixes"
* tag 'arc-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARCv2: entry: Fix reserved handler
ARCv2: perf: Finally introduce HS perf unit
ARCv2: perf: SMP support
ARCv2: perf: implement exclusion of event counting in user or kernel mode
ARCv2: perf: Support sampling events using overflow interrupts
ARCv2: perf: implement "event_set_period"
ARC: perf: cap the number of counters to hardware max of 32
ARC: Eliminate some ARCv2 specific code for ARCompact build
ARC: add/fix some comments in code - no functional change
ARC: change some branchs to jumps to resolve linkage errors
ARC: ensure futex ops are atomic in !LLSC config
ARC: Enable HAVE_FUTEX_CMPXCHG
ARC: make futex_atomic_cmpxchg_inatomic() return bimodal
ARC: futex cosmetics
ARC: add barriers to futex code
ARCv2: IOC: Allow boot time disable
ARCv2: SLC: Allow boot time disable
ARCv2: Support IO Coherency and permutations involving L1 and L2 caches
ARC: Enable optimistic spinning for LLSC config
MAINTAINERS: add git tree for the arc architecture
* pm-sleep:
PM / suspend: make sync() on suspend-to-RAM build-time optional
PM / sleep: Allow devices without runtime PM to do direct-complete
PM / autosleep: Use workqueue for user space wakeup sources garbage collector
* pm-domains:
PM / Domains: Fix typo in description of genpd_dev_pm_detach()
PM / Domains: Remove unusable governor dummies
PM / Domains: Make pm_genpd_init() available to modules
PM / domains: Align column headers and data in pm_genpd_summary output
PM / Domains: Return -EPROBE_DEFER if we fail to init or turn-on domain
PM / Domains: Correct unit address in power-controller example
PM / Domains: Remove intermediate states from the power off sequence
* pm-avs:
PM / AVS: rockchip-io: add io selectors and supplies for rk3368
PM / AVS: rockchip-io: depend on CONFIG_POWER_AVS
* pm-cpuidle:
cpuidle/coupled: Remove redundant 'dev' argument of cpuidle_state_is_coupled()
cpuidle/coupled: Remove cpuidle_device::safe_state_index
intel_idle: Skylake Client Support
intel_idle: allow idle states to be freeze-mode specific
* pm-devfreq:
PM / devfreq: exynos-ppmu: Update documentation to support PPMUv2
PM / devfreq: exynos-ppmu: Add the support of PPMUv2 for Exynos5433
PM / devfreq: event: Remove incorrect property in exynos-ppmu DT binding
* pm-clk:
PM / clk: don't return int on __pm_clk_enable()
Linus Torvalds
Kevin Hilman
Andy Gross
Wenyou Yang
Ariel D'Alessandro
Alexandre Belloni
Haibo Chen
Sanchayan Maity
Keerthy
Suneel Garapati
Joachim Eastwood
Corey Minyard
Russell King
Ezequiel Garcia
Rafael J. Wysocki