The ISP1760 has some timing requirements where it has to delay a short
period after a write to a register has started. However, this delay is
from the time the write hits the USB chip (the ISP1760), not from the
time where the processor started processing the write. So on a quick
enough processor, it is sometimes possible for the write to not hit the
device before we start delaying, and we then violate the part's timing
requirements, so things stop working.
To avoid all this, insert a write barrier after the register write and
before the timing delay/register read so we can guarantee we only start
counting time after the write has hit the device.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1393) converts several of the single-bit fields in
struct usb_hcd to atomic flags. This is for safety's sake; not all
CPUs can update bitfield values atomically, and these flags are used
in multiple contexts.
The flag fields that are set only during registration or removal can
remain as they are, since non-atomic accesses at those times will not
cause any problems.
(Strictly speaking, the authorized_default flag should become atomic
as well. I didn't bother with it because it gets changed only via
sysfs. It can be done later, if anyone wants.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There were some reports[1] of isp1760 USB driver malfunctioning
with high speed devices, noticed on Blackfin and PowerPC targets.
These reports indicated that the original Philips 'pehcd'[2]
driver worked fine.
We've noticed the same issue with an ARM RealView platform. This
happens under load (with only some mass storage devices, not all,
just as in another report[3]):
error bit is set in DW3
error bit is set in DW3
error bit is set in DW3
usb 1-1.2: device descriptor read/64, error -32
It appears that the 'pehcd' driver checks the X bit only if the
transaction is halted (H bit), otherwise the error is so far
insignificant.
The ISP176x chips were modeled after EHCI, and EHCI spec says
(thanks to Alan Stern for pointing out):
"Transaction errors cause the status field to be updated to reflect
the type of error, but the transaction continues to be retried until
the Active bit is set to 0. When the error counter reaches 0, the
Halt bit is set and the Active bit is cleared."
So, just as the original Philips driver, isp1760 must report the
error only if the transaction error and the halt bits are set.
[1] http://markmail.org/message/lx4qrlbrs2uhcnly
[2] svn co svn://sources.blackfin.uclinux.org/linux-kernel/trunk/drivers/usb/host -r 5494
See pehci.c:pehci_hcd_update_error_status().
[3] http://blackfin.uclinux.org/gf/tracker/5148
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1349b) clears up the confusion in many USB host
controller drivers between port features and port statuses. In mosty
cases it's true that the status bit is in the position given by the
corresponding feature value, but that's not always true and it's not
guaranteed in the USB spec.
There's no functional change, just replacing expressions of the form
(1 << USB_PORT_FEAT_x) with USB_PORT_STAT_x, which has the same value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1348) removes the bogus
USB_PORT_FEAT_{HIGHSPEED,SUPERSPEED} symbols from ch11.h. No such
features are defined by the USB spec. (There is a PORT_LOWSPEED
feature, but the spec doesn't mention it except to say that host
software should never use it.) The speed indicators are port
statuses, not port features.
As a temporary workaround for the xhci-hcd driver, a fictional
USB_PORT_STAT_SUPER_SPEED symbol is added.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usbcore headers: hcd.h and hub.h are shared between usbcore,
HCDs and a couple of other drivers (e.g. USBIP modules).
So, it makes sense to move them into a more public location and
to cleanup dependency of those modules on kernel internal headers.
This patch moves hcd.h from drivers/usb/core into include/linux/usb/
Signed-of-by: Eric Lescouet <eric@lescouet.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the HDC driver writes the data to the transfer buffers it pollutes
the D-cache (unlike DMA drivers where the device writes the data). If
the corresponding pages get mapped into user space, there are no
additional cache flushing operations performed and this causes random
user space faults on architectures with separate I and D caches
(Harvard) or those with aliasing D-cache.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Matthew Dharm <mdharm-kernel@one-eyed-alien.net>
Cc: Greg KH <greg@kroah.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This error message is not actually an error, it's an information
message. It is triggered when a transfer which ended in a NAQ is
retried successfully by the hardware.
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Platform device support was merged earlier, but support for boards to
customize the devflags aspect of the controller was not. We want this on
Blackfin systems to control the bus width, but might as well expose all of
the fields while we're at it.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The option driver (and presumably others) allocates several URBs when it
opens and tries to free them when it closes. The isp1760_urb_dequeue
function gets called, but the packet being dequeued is not necessarily at
the
front of one of the 32 queues. If not, the isp1760_urb_done function doesn't
get called for the URB and the process trying to free it hangs forever on a
wait_queue. This patch does two things. If the URB being dequeued has others
queued behind it, it re-queues them. And it searches the queues looking for
the URB being dequeued rather than just looking at the one at the front of
the queue.
[bigeasy@linutronix] whitespace fixes, reformating
Cc: stable <stable@kernel.org>
Signed-off-by: Warren Free <wfree@ipmn.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The data read from the SKIPMAP registers is not immediately available
after writing and the driver panics when a packet is enqueued from the
interrupt handler. This patch adds an ndelay(195) before these registers
are read (delay value mentioned in section 15.1.1.3 of the ISP1760 data
sheet).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch changes the prototype of the isp1760_register() function to use
predefined types like phys_addr_t and resource_size_t rather than u64
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no need to disable port 1 on ISP1761. That port could
be used as an OTG port which would require a different init
sequence. However we don't have OTG support (yet) so we can use
it as a normal USB port.
This patch allows port 1 to be used a normal Port on the ISP1761.
Signed-off-by: Thomas Hommel <Thomas.Hommel@gefanuc.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to Alan Stern, short packets are quite normal under
certain circumstances. This printk was triggered by usb to
serial converters on every packet and some usb sticks triggered
a few of those while plugging the stick.
This printks are now hidden unless USB debug mode is activated.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ISP1760 requires a delay of 90ns between programming the address and
reading the data. Current driver solves this by a mdelay(1) which is
very heavy weighted and slow. This patch applies the workaround from
the ISP1760 FAQ by using two different banks for PTD and payload data
and using a common wait for them. This wait is done by an additional
ISP1760 access (whose timing constraints guarantee the 90ns delay).
This improves speed when reading from an USB stick from:
$ time dd if=/dev/sda of=/dev/zero bs=65536 count=1638
real 1m 15.43s
user 0m 0.44s
sys 0m 39.46s
to
$ time dd if=/dev/sda of=/dev/zero bs=65536 count=1638
real 0m 18.53s
user 0m 0.16s
sys 0m 12.97s
[bigeasy@linutronix.de: fixed comment formating, moved define into
header file, obey 80 char rule]
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
if the enqueue function returns -ESHUTDOWN or -ENOMEM then
we return 0 instead of an error. This leads to a timeout and
then to a dequeue request of an not enqueued urb.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for hardware configurations that don't match the
chip default register settings (e.g., 16-bit data bus, DACK and
DREQ pulled up instead of down, analog overcurrent mode).
These settings are passed in via the OF device tree. The PCI
interface still assumes the same default values.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the following needlessly global functions static:
- enqueue_an_ATL_packet()
- enqueue_an_INT_packet()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bus_id field is going away, use the dev_set_name() function
to set it properly.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the bogus "io mem 0x00000000" message printed
during driver init due to hcd->rsrc_start being assigned after
the call to usb_add_hcd().
Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix printk format warnings in isp1760 (in linux-next):
next-20080430/drivers/usb/host/isp1760-hcd.c:994: warning: format '%d' expects type 'int', but argument 6 has type 'size_t'
next-20080430/drivers/usb/host/isp1760-hcd.c:1092: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver has been written from scratch and supports the ISP1760. ISP1761
might (should) work as well but the OTG isn't supported. Also ISO packets are
not. However, it works on my little PowerPC board.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Michael Hennerich
Alan Stern
Anton Vorontsov
Eric Lescouet
Catalin Marinas
Colin Tuckley
Warren Free
Harvey Harrison
Thomas Hommel
Enrico Scholz
Sebastian Siewior
Nate Case
Andrew Morton
Adrian Bunk
Kay Sievers
Randy Dunlap
Sebastian Siewior