Handling of connection-related message reception is currently scattered
around at different places in the code. This makes it harder to verify
that things are handled correctly in all possible scenarios.
So we consolidate the existing processing of connection-oriented
message reception in a single routine. In the process, we convert the
chain of if/else into a switch/case for improved readability.
A cast on the socket_state in the switch is needed to avoid compile
warnings on 32 bit, like "net/tipc/socket.c:1252:2: warning: case value
‘4294967295’ not in enumerated type". This happens because existing
tipc code pseudo extends the default linux socket state values with:
#define SS_LISTENING -1 /* socket is listening */
#define SS_READY -2 /* socket is connectionless */
It may make sense to add these as _positive_ values to the existing
socket state enum list someday, vs. these already existing defines.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
[PG: add cast to fix warning; remove returns from middle of switch]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Currently we have tipc_disconnect and tipc_disconnect_port. It is
not clear from the names alone, what they do or how they differ.
It turns out that tipc_disconnect just deals with the port locking
and then calls tipc_disconnect_port which does all the work.
If we rename as follows: tipc_disconnect_port --> __tipc_disconnect
then we will be following typical linux convention, where:
__tipc_disconnect: "raw" function that does all the work.
tipc_disconnect: wrapper that deals with locking and then calls
the real core __tipc_disconnect function
With this, the difference is immediately evident, and locking
violations are more apt to be spotted by chance while working on,
or even just while reading the code.
On the connect side of things, we currently only have the single
"tipc_connect2port" function. It does both the locking at enter/exit,
and the core of the work. Pending changes will make it desireable to
have the connect be a two part locking wrapper + worker function,
just like the disconnect is already.
Here, we make the connect look just like the updated disconnect case,
for the above reason, and for consistency. In the process, we also
get rid of the "2port" suffix that was on the original name, since
it adds no descriptive value.
On close examination, one might notice that the above connect
changes implicitly move the call to tipc_link_get_max_pkt() to be
within the scope of tipc_port_lock() protected region; when it was
not previously. We don't see any issues with this, and it is in
keeping with __tipc_connect doing the work and tipc_connect just
handling the locking.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The sk_recv_queue upper limit for connectionless sockets has empirically
turned out to be too low. When we double the current limit we get much
fewer rejected messages and no noticable negative side-effects.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
As a complement to the per-socket sk_recv_queue limit, TIPC keeps a
global atomic counter for the sum of sk_recv_queue sizes across all
tipc sockets. When incremented, the counter is compared to an upper
threshold value, and if this is reached, the message is rejected
with error code TIPC_OVERLOAD.
This check was originally meant to protect the node against
buffer exhaustion and general CPU overload. However, all experience
indicates that the feature not only is redundant on Linux, but even
harmful. Users run into the limit very often, causing disturbances
for their applications, while removing it seems to have no negative
effects at all. We have also seen that overall performance is
boosted significantly when this bottleneck is removed.
Furthermore, we don't see any other network protocols maintaining
such a mechanism, something strengthening our conviction that this
control can be eliminated.
As a result, the atomic variable tipc_queue_size is now unused
and so it can be deleted. There is a getsockopt call that used
to allow reading it; we retain that but just return zero for
maximum compatibility.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
[PG: phase out tipc_queue_size as pointed out by Neil Horman]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Each link instance has a periodic job checking if there is a stale
ongoing message reassembly associated to the link. If no new
fragment has been received during the last 4*[link_tolerance] period,
it is assumed the missing fragment will never arrive. As a consequence,
the reassembly buffer is discarded, and a gap in the message sequence
occurs.
This assumption is wrong. After we abandoned our ambition to develop
packet routing for multi-cluster networks, only single-hop packet
transfer remains as an option. For those, all packets are guaranteed
to be delivered in sequence to the defragmentation layer. Any failure
to achieve sequenced delivery will eventually lead to link reset, and
the reassembly buffer will be flushed anyway.
So we just remove this periodic check, which is now obsolete.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
[PG: also delete get/inc_timer count, since they are now unused]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
There used to be a time when TIPC had lots of Kconfig knobs the
end user could alter, but they have all been made automatic or
obsolete, with the exception of CONFIG_TIPC_PORTS. This
previously existing set of options was all hidden under the
TIPC_ADVANCED setting, which does not exist in any code, but
only in Kconfig scope.
Having this now, just to hide the one remaining "advanced"
option no longer makes sense. Remove it. Also get rid of the
ifdeffery in the TIPC code that allowed for TIPC_PORTS to be
possibly undefined.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
As the variable:node is currently defined to u32 type, it is
unnecessary to cast its type to u32 again when using it.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Upon establishing a first link between two nodes, there is
currently a risk that the two endpoints will disagree on exactly
which sequence number reception and acknowleding of broadcast
packets should start.
The following scenarios may happen:
1: Node A sends an ACTIVATE message to B, telling it to start acking
packets from sequence number N.
2: Node A sends out broadcast N, but does not expect an acknowledge
from B, since B is not yet in its broadcast receiver's list.
3: Node A receives ACK for N from all nodes except B, and releases
packet N.
4: Node B receives the ACTIVATE, activates its link endpoint, and
stores the value N as sequence number of first expected packet.
5: Node B sends a NAME_DISTR message to A.
6: Node A receives the NAME_DISTR message, and activates its endpoint.
At this moment B is added to A's broadcast receiver's set.
Node A also sets sequence number 0 as the first broadcast packet
to be received from B.
7: Node A sends broadcast N+1.
8: B receives N+1, determines there is a gap in the sequence, since
it is expecting N, and sends a NACK for N back to A.
9: Node A has already released N, so no retransmission is possible.
The broadcast link in direction A->B is stale.
In addition to, or instead of, 7-9 above, the following may happen:
10: Node B sends broadcast M > 0 to A.
11: Node A receives M, falsely decides there must be a gap, since
it is expecting packet 0, and asks for retransmission of packets
[0,M-1].
12: Node B has already released these packets, so the broadcast
link is stale in direction B->A.
We solve this problem by introducing a new unicast message type,
BCAST_PROTOCOL/STATE, to convey the sequence number of the next
sent broadcast packet to the other endpoint, at exactly the moment
that endpoint is added to the own node's broadcast receivers list,
and before any other unicast messages are permitted to be sent.
Furthermore, we don't allow any node to start receiving and
processing broadcast packets until this new synchronization
message has been received.
To maintain backwards compatibility, we still open up for
broadcast reception if we receive a NAME_DISTR message without
any preceding broadcast sync message. In this case, we must
assume that the other end has an older code version, and will
never send out the new synchronization message. Hence, for mixed
old and new nodes, the issue arising in 7-12 of the above may
happen with the same probability as before.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Rename the "supported" flag in bclink structure to "recv_permitted"
to better reflect what it is used for. When this flag is set for a
given node, we are permitted to receive and acknowledge broadcast
messages from that node. Convert it to a bool at the same time,
since it is not used to store any numerical values.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The "supportable" flag in bclink structure is a compatibility flag
indicating whether a peer node is capable of receiving TIPC broadcast
messages. However, all TIPC versions since tipc-1.5, and after the
inclusion in the upstream Linux kernel in 2006, support this capability.
It is highly unlikely that anybody is still using such an old
version of TIPC, let alone that they want to mix it with TIPC-2.0
nodes. Therefore, we now remove the "supportable" flag.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Currently at the TIPC bearer layer there is the following congestion
mechanism:
Once sending packets has failed via that bearer, the bearer will be
flagged as being in congested state at once. During bearer congestion,
all packets arriving at link will be queued on the link's outgoing
buffer. When we detect that the state of bearer congestion has
relaxed (e.g. some packets are received from the bearer) we will try
our best to push all packets in the link's outgoing buffer until the
buffer is empty, or until the bearer is congested again.
However, in fact the TIPC bearer never receives any feedback from the
device layer whether a send was successful or not, so it must always
assume it was successful. Therefore, the bearer congestion mechanism
as it exists currently is of no value.
But the bearer blocking state is still useful for us. For example,
when the physical media goes down/up, we need to change the state of
the links bound to the bearer. So the code maintaing the state
information is not removed.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
When a socket is shut down, we should wake up all thread sleeping on
it, instead of just one of them. Otherwise, when several threads are
polling the same socket, and one of them does shutdown(), the
remaining threads may end up sleeping forever.
Also, to align socket usage with common practice in other stacks, we
use one of the common socket callback handlers, sk_state_change(),
to wake up pending users. This is similar to the usage in e.g.
inet_shutdown(). [net/ipv4/af_inet.c].
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
If an implied connect is attempted on a nonblocking STREAM/SEQPACKET
socket during link congestion, the connect message will be discarded
and sendmsg will return EAGAIN. This is normal behavior, and the
application is expected to poll the socket until POLLOUT is set,
after which the connection attempt can be retried.
However, the POLLOUT flag is never set for unconnected sockets and
poll() always returns a zero mask. The application is then left without
a trigger for when it can make another attempt at sending the message.
The solution is to check if we're polling on an unconnected socket
and set the POLLOUT flag if the TIPC port owned by this socket
is not congested. The TIPC ports waiting on a specific link will be
marked as 'not congested' when the link congestion have abated.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
When an application blocks at poll/select on a TIPC socket
while requesting a specific event mask, both the filter_rcv() and
wakeupdispatch() case will wake it up unconditionally whenever
the state changes (i.e an incoming message arrives, or congestion
has subsided). No mask is used.
To avoid this, we populate sk->sk_data_ready and sk->sk_write_space
with tipc_data_ready and tipc_write_space respectively, which makes
tipc more in alignment with the rest of the networking code. These
pass the exact set of possible events to the waker in fs/select.c
hence avoiding waking up blocked processes unnecessarily.
In doing so, we uncover another issue -- that there needs to be a
memory barrier in these poll/receive callbacks, otherwise we are
subject to the the same race as documented above wq_has_sleeper()
[in commit a57de0b4 "net: adding memory barrier to the poll and
receive callbacks"]. So we need to replace poll_wait() with
sock_poll_wait() and use rcu protection for the sk->sk_wq pointer
in these two new functions.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
If tasklet_disable() is called before related tasklet handled,
tasklet_kill will never be finished. tasklet_kill is enough.
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Allan Stephens <allan.stephens@windriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: tipc-discussion@lists.sourceforge.net
Signed-off-by: David S. Miller <davem@davemloft.net>
When large buffers are sent over connected TIPC sockets, it
is likely that the sk_backlog will be filled up on the
receiver side, but the TIPC flow control mechanism is happily
unaware of this since that is based on message count.
The sender will receive a TIPC_ERR_OVERLOAD message when this occurs
and drop it's side of the connection, leaving it stale on
the receiver end.
By increasing the sk_rcvbuf to a 'worst case' value, we avoid the
overload caused by a full backlog queue and the flow control
will work properly.
This worst case value is the max TIPC message size times
the flow control window, multiplied by two because a sender
will transmit up to double the window size before a port is marked
congested.
We multiply this by 2 to account for the sk_buff and other overheads.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a frequent mistake to confuse the netlink port identifier with a
process identifier. Try to reduce this confusion by renaming fields
that hold port identifiers portid instead of pid.
I have carefully avoided changing the structures exported to
userspace to avoid changing the userspace API.
I have successfully built an allyesconfig kernel with this change.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gets rid of the need for users to specify the maximum number of
name publications supported by TIPC. TIPC now automatically provides
support for the maximum number of name publications to 65535.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gets rid of the need for users to specify the maximum number of
name subscriptions supported by TIPC. TIPC now automatically provides
support for the maximum number of name subscriptions to 65535.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added to the following:
- tipc_random
- tipc_own_addr
- tipc_max_ports
- tipc_net_id
- tipc_remote_management
- handler_enabled
The above global variables are read often, but written rarely. Use
__read_mostly to prevent them being on the same cacheline as another
variable which is written to often, which would cause cacheline
bouncing.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing changing this variable dynamically, so change
it to a macro to make that more obvious when reading the code.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since now tipc_net_start() always returns a success code - 0, its
return value type should be changed from integer to void, which can
avoid unnecessary check for its return value.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After eliminating the mechanism which checks whether all letters
in media name string are within a given character set, the
media_name_valid routine becomes trivial. It is also only
used once, so it is unnecessary to keep it as a separate function.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no real reason to check whether all letters in the given
media name and network interface name are within the character set
defined in tipc_alphabet array. Even if we eliminate the checking,
the rest of checking conditions in tipc_enable_bearer() can ensure
we do not enable an invalid or illegal bearer.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the lockdep validator is enabled, it will report the below
warning when we enable a TIPC bearer:
[ INFO: possible irq lock inversion dependency detected ]
---------------------------------------------------------
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(ptype_lock);
local_irq_disable();
lock(tipc_net_lock);
lock(ptype_lock);
<Interrupt>
lock(tipc_net_lock);
*** DEADLOCK ***
the shortest dependencies between 2nd lock and 1st lock:
-> (ptype_lock){+.+...} ops: 10 {
[...]
SOFTIRQ-ON-W at:
[<c1089418>] __lock_acquire+0x528/0x13e0
[<c108a360>] lock_acquire+0x90/0x100
[<c1553c38>] _raw_spin_lock+0x38/0x50
[<c14651ca>] dev_add_pack+0x3a/0x60
[<c182da75>] arp_init+0x1a/0x48
[<c182dce5>] inet_init+0x181/0x27e
[<c1001114>] do_one_initcall+0x34/0x170
[<c17f7329>] kernel_init+0x110/0x1b2
[<c155b6a2>] kernel_thread_helper+0x6/0x10
[...]
... key at: [<c17e4b10>] ptype_lock+0x10/0x20
... acquired at:
[<c108a360>] lock_acquire+0x90/0x100
[<c1553c38>] _raw_spin_lock+0x38/0x50
[<c14651ca>] dev_add_pack+0x3a/0x60
[<c8bc18d2>] enable_bearer+0xf2/0x140 [tipc]
[<c8bb283a>] tipc_enable_bearer+0x1ba/0x450 [tipc]
[<c8bb3a04>] tipc_cfg_do_cmd+0x5c4/0x830 [tipc]
[<c8bbc032>] handle_cmd+0x42/0xd0 [tipc]
[<c148e802>] genl_rcv_msg+0x232/0x280
[<c148d3f6>] netlink_rcv_skb+0x86/0xb0
[<c148e5bc>] genl_rcv+0x1c/0x30
[<c148d144>] netlink_unicast+0x174/0x1f0
[<c148ddab>] netlink_sendmsg+0x1eb/0x2d0
[<c1456bc1>] sock_aio_write+0x161/0x170
[<c1135a7c>] do_sync_write+0xac/0xf0
[<c11360f6>] vfs_write+0x156/0x170
[<c11361e2>] sys_write+0x42/0x70
[<c155b0df>] sysenter_do_call+0x12/0x38
[...]
}
-> (tipc_net_lock){+..-..} ops: 4 {
[...]
IN-SOFTIRQ-R at:
[<c108953a>] __lock_acquire+0x64a/0x13e0
[<c108a360>] lock_acquire+0x90/0x100
[<c15541cd>] _raw_read_lock_bh+0x3d/0x50
[<c8bb874d>] tipc_recv_msg+0x1d/0x830 [tipc]
[<c8bc195f>] recv_msg+0x3f/0x50 [tipc]
[<c146a5fa>] __netif_receive_skb+0x22a/0x590
[<c146ab0b>] netif_receive_skb+0x2b/0xf0
[<c13c43d2>] pcnet32_poll+0x292/0x780
[<c146b00a>] net_rx_action+0xfa/0x1e0
[<c103a4be>] __do_softirq+0xae/0x1e0
[...]
}
>From the log, we can see three different call chains between
CPU0 and CPU1:
Time 0 on CPU0:
kernel_init()->inet_init()->dev_add_pack()
At time 0, the ptype_lock is held by CPU0 in dev_add_pack();
Time 1 on CPU1:
tipc_enable_bearer()->enable_bearer()->dev_add_pack()
At time 1, tipc_enable_bearer() first holds tipc_net_lock, and then
wants to take ptype_lock to register TIPC protocol handler into the
networking stack. But the ptype_lock has been taken by dev_add_pack()
on CPU0, so at this time the dev_add_pack() running on CPU1 has to be
busy looping.
Time 2 on CPU0:
netif_receive_skb()->recv_msg()->tipc_recv_msg()
At time 2, an incoming TIPC packet arrives at CPU0, hence
tipc_recv_msg() will be invoked. In tipc_recv_msg(), it first wants
to hold tipc_net_lock. At the moment, below scenario happens:
On CPU0, below is our sequence of taking locks:
lock(ptype_lock)->lock(tipc_net_lock)
On CPU1, our sequence of taking locks looks like:
lock(tipc_net_lock)->lock(ptype_lock)
Obviously deadlock may happen in this case.
But please note the deadlock possibly doesn't occur at all when the
first TIPC bearer is enabled. Before enable_bearer() -- running on
CPU1 does not hold ptype_lock, so the TIPC receive handler (i.e.
recv_msg()) is not registered successfully via dev_add_pack(), so
the tipc_recv_msg() cannot be called by recv_msg() even if a TIPC
message comes to CPU0. But when the second TIPC bearer is
registered, the deadlock can perhaps really happen.
To fix it, we will push the work of registering TIPC protocol
handler into workqueue context. After the change, both paths taking
ptype_lock are always in process contexts, thus, the deadlock should
never occur.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet media initialization is only done when TIPC is started or
switched to network mode. So the initialization of the network device
notifier structure can be moved out of this function and done
statically instead.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal log buffer handling functions can now safely be
removed since there is no code using it anymore. Requests to
interact with the internal tipc log buffer over netlink (in
config.c) will report 'obsolete command'.
This represents the final removal of any references to a
struct print_buf, and the removal of the struct itself.
We also get rid of a TIPC specific Kconfig in the process.
Finally, log.h is removed since it is not needed anymore.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The tipc_printf is renamed to tipc_snprintf, as the new name
describes more what the function actually does. It is also
changed to take a buffer and length parameter and return
number of characters written to the buffer. All callers of
this function that used to pass a print_buf are updated.
Final removal of the struct print_buf itself will be done
synchronously with the pending removal of the deprecated
logging code that also was using it.
Functions that build up a response message with a list of
ports, nametable contents etc. are changed to return the number
of characters written to the output buffer. This information
was previously hidden in a field of the print_buf struct, and
the number of chars written was fetched with a call to
tipc_printbuf_validate. This function is removed since it
is no longer referenced nor needed.
A generic max size ULTRA_STRING_MAX_LEN is defined, named
in keeping with the existing TIPC_TLV_ULTRA_STRING, and the
various definitions in port, link and nametable code that
largely duplicated this information are removed. This means
that amount of link statistics that can be returned is now
increased from 2k to 32k.
The buffer overflow check is now done just before the reply
message is passed over netlink or TIPC to a remote node and
the message indicating a truncated buffer is changed to a less
dramatic one (less CAPS), placed at the end of the message.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
tipc_printf was previously used both to construct debug traces
and to append data to buffers that should be sent over netlink
to the tipc-config application. A global print_buffer was
used to format the string before it was copied to the actual
output buffer. This could lead to concurrent access of the
global print_buffer, which then had to be lock protected.
This is simplified by changing tipc_printf to append data
directly to the output buffer using vscnprintf.
With the new implementation of tipc_printf, there is no longer
any risk of concurrent access to the internal log buffer, so
the lock (and the comments describing it) are no longer
strictly necessary. However, there are still a few functions
that do grab this lock before resizing/dumping the log
buffer. We leave the lock, and these functions untouched since
they will be removed with a subsequent commit that drops the
deprecated log buffer handling code
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
To pave the way for a pending cleanup of tipc_printf, and
removal of struct print_buf entirely, we make that task simpler
by converting link_print to issue its messages with standard
printk infrastructure. [Original idea separated from a larger
patch from Erik Hugne <erik.hugne@ericsson.com>]
Cc: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The link queue traces and packet level debug functions served
a purpose during early development, but are now redundant
since there are other, more capable tools available for
debugging at the packet level.
The TIPC_DEBUG Kconfig option is removed since it does not
provide any extra debugging features anymore.
This gets rid of a lot of tipc_printf usages, which will
make the pending cleanup work of that function easier.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
All messages should go directly to the kernel log. The TIPC
specific error, warning, info and debug trace macro's are
removed and all references replaced with pr_err, pr_warn,
pr_info and pr_debug.
Commonly used sub-strings are explicitly declared as a const
char to reduce .text size.
Note that this means the debug messages (changed to pr_debug),
are now enabled through dynamic debugging, instead of a TIPC
specific Kconfig option (TIPC_DEBUG). The latter will be
phased out completely
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
[PG: use pr_fmt as suggested by Joe Perches <joe@perches.com>]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
With the default name table size of 1024, it is possible that
the sanity check in tipc_nametbl_stop could spam out 1024
essentially identical error messages if memory was corrupted
or similar. Limit it to issuing no more than a single message.
The actual chain number (i.e. 0 --> 1023) wouldn't provide any
useful insight if/when such an instance happened, so don't
bother printing out that value.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This is done to improve readability, and so that we can give
the struct a name that will allow us to declare a local
pointer to it in code, instead of having to always redirect
through the link struct to get to it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding casts of objects to the same type is unnecessary
and confusing for a human reader.
For example, this cast:
int y;
int *p = (int *)&y;
I used the coccinelle script below to find and remove these
unnecessary casts. I manually removed the conversions this
script produces of casts with __force and __user.
@@
type T;
T *p;
@@
- (T *)p
+ p
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the comment blocks are floating in limbo between two
functions, or between blocks of code. Delete the extra line
feeds between any comment and its associated following block
of code, to be consistent with the majority of the rest of
the kernel. Also delete trailing newlines at EOF and fix
a couple trivial typos in existing comments.
This is a 100% cosmetic change with no runtime impact. We get
rid of over 500 lines of non-code, and being blank line deletes,
they won't even show up as noise in git blame.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Adds check to ensure TIPC sockets reject incoming payload messages
that have an unrecognized message type.
Remove the old open question about whether TIPC_ERR_NO_PORT is
the proper return value. It is appropriate here since there are
valid instances where another node can make use of the reply,
and at this point in time the host is already broadcasting TIPC
data, so there are no real security concerns.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Consolidates validation of scope and name sequence range values into
a single routine where it applies both to local name publications
and to name publications issued by other nodes in the network. This
change means that the scope value for non-local publications is now
validated and the name sequence range for local publications is now
validated only once. Additionally, a publication attempt that fails
validation now creates an entry in the system log file only if debugging
capabilities have been enabled; this prevents the system log from being
cluttered up with messages caused by a defective application or network
node.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Replaces two identical chunks of code that delete an unused name
sequence structure from TIPC's name table with calls to a new routine
that performs this operation.
This change is cosmetic and doesn't impact the operation of TIPC.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminate code to zero-out the main topology service structure,
which is already zeroed-out.
Get rid of a comment documenting a field of the main topology
service structure that no longer exists.
Both are cosmetic changes with no impact on runtime behaviour.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Initialization now occurs in the calling thread of control,
rather than being deferred to the TIPC tasklet. With the
current codebase, the deferral is no longer necessary.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Streamlines the job of re-initializing TIPC's network topology service
when a node's network address is first assigned. Rather than destroying
the topology server port and breaking its connections to existing
subscribers, TIPC now simply lets the service continue running (since
the change to the port identifier of each port used by the topology
service no longer impacts the flow of messages between the service and
its subscribers).
This enhancement means that applications that utilize the topology
service prior to the assignment of TIPC's network address no longer need
to re-establish their subscriptions when the address is finally assigned.
However, it is worth noting that any subsequent events for existing
subscriptions report the new port identifier of the publishing port,
rather than the original port identifier. (For example, a name that was
previously reported as being published by <0.0.0:ref> may be subsequently
withdrawn by <Z.C.N:ref>.)
This doesn't impact any of the existing known userspace in tipc-utils,
since (a) TIPC continues to treat references to the original port ID
correctly and (b) normal use cases assign an address before active use.
However if there does happen to be some rare/custom application out
there that was relying on this, they can simply bypass the enhancement
by issuing a subscription to {0,0} and break its connection to the
topology service, if an associated withdrawal event occurs.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Termination no longer tests to see if the configuration service
port was successfully created or not. In the unlikely event that the
port was not created, attempting to delete the non-existent port is
detected gracefully and causes no harm.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Initialization now occurs in the calling thread of control,
rather than being deferred to the TIPC tasklet. With the
current codebase, the deferral is no longer necessary.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Streamlines the job of re-initializing TIPC's configuration service
when a node's network address is first assigned. Rather than destroying
the configuration server port and then recreating it, TIPC now simply
withdraws the existing {0,<0.0.0>} name publication and creates a new
{0,<Z.C.N>} name publication that identifies the node's network address
to interested subscribers.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Untie gcc's hands and let it do what it wants within the
individual source files. There are two files, node.c and
port.c -- only the latter effectively changes (gcc-4.5.2).
Objdump shows gcc deciding to not inline port_peernode().
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_add_backlog() & sk_rcvqueues_full() hard coded sk_rcvbuf as the
memory limit. We need to make this limit a parameter for TCP use.
No functional change expected in this patch, all callers still using the
old sk_rcvbuf limit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enhances command validation done by TIPC's configuration service so
that it works properly even if the node's network address is changed in
mid-operation. The default node address of <0.0.0> is now recognized as an
alias for "this node" even after a new network address has been assigned.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Revises handling of a rejected message to ensure that a locally
originated message is returned properly even if the node's network
address is changed in mid-operation. The routine now treats the
default node address of <0.0.0> as an alias for "this node" when
determining where to send a returned message.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Revises handling of send routines for payload messages to ensure that
they are processed properly even if the node's network address is
changed in mid-operation. The routines now treat the default node
address of <0.0.0> as an alias for "this node" when determining where
to send an outgoing message.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
There are two send routines that might conceivably be asked by an
application to send a message off-node when the node is still using
the default network address. These now have an added check that
detects this and rejects the message gracefully.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The routine that changes the node's network address now takes TIPC's
network lock in write mode while the main address variable and associated
data structures are being changed; this is needed to ensure that the
link subsystem won't attempt to send a message off-node until the sending
port's message header template has been updated with the node's new
network address.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Revises routines that deal with connections between two ports on
the same node to ensure the connection is not impacted if the node's
network address is changed in mid-operation. The routines now treat
the default node address of <0.0.0> as an alias for "this node" in
the following situations:
1) Incoming messages destined to a connected port now handle the alias
properly when validating that the message was sent by the expected
peer port, ensuring that the message will be accepted regardless of
whether it specifies the node's old network address or it's current one.
2) The code which completes connection establishment now handles the
alias properly when determining if the peer port is on the same node
as the connected port.
An added benefit of addressing issue 1) is that some peer port
validation code has been relocated to TIPC's socket subsystem, which
means that validation is no longer done twice when a message is
sent to a non-socket port (such as TIPC's configuration service or
network topology service).
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Prior to commit 23dd4cce38
"tipc: Combine port structure with tipc_port structure"
there was a need for the two sets of helper functions. But
now they are just duplicates. Remove the globally visible
ones, and mark the remaining ones as inline.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Re-orders port creation logic so that the initialization of a new
port's message header template occurs while the port list lock is
held. This ensures that a change to the node's network address that
occurs at the same time as the port is being created does not result
in the template identifying the sender using the former network
address. The new approach guarantees that the new port's template is
using the current network address or that it will be updated when
the address changes.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Removes an unnecessary check in the logic that updates the message
header template for existing ports when a node's network address is
first assigned. There is no longer any need to check to see if the
node's network address has actually changed since the calling routine
has already verified that this is so.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Revises routines that add and remove an entry from a node's name table
so that the publication scope lists are updated properly even if the
node's network address is changed in mid-operation. The routines now
recognize the default node address of <0.0.0> as an alias for "this node"
even after a new network address has been assigned.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Introduces routines that test whether a given network address is
equal to a node's own network address or if it lies within the node's
own network cluster, and which work properly regardless of whether
the node is using the default network address <0.0.0> or a non-zero
network address that is assigned later on. In essence, these routines
ensure that address <0.0.0> is treated as an alias for "this node",
regardless of which network address the node is actually using.
Old users of the pre-existing more strict match in_own_cluster()
have been accordingly redirected to what is now called
in_own_cluster_exact() --- which does not extend matching to <0,0,0>.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
No longer increments counter of number of publications by a node
if an attempt to add a new publication fails. This prevents TIPC from
incorrectly blocking future publications because the configured maximum
number of publications has been reached.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensures that node-scope name publications that exist prior to the
configuration of a node's network address are properly re-initialized
with that address when it is assigned. TIPC's node-scope publications
are now tracked using a publications list like the lists used for
cluster-scope and zone-scope publications so they can be easily updated
when required.
The inclusion of node scope name publications in a conventional publication
list means that they must now also be withdrawn, just like cluster and zone
scope publications are currently withdrawn. So some conditional tests on
scope ==/!= TIPC_NODE_SCOPE are inserted/removed accordingly.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Utilizes distinct lists to track zone-scope and cluster-scope names
published by a node. For now, TIPC continues to process the entries
in both lists in the same way; however, an upcoming patch will utilize
the existence of the lists to prevent the sending of cluster-scope names
to nodes that are not part of the local cluster.
To achieve this, an array of publication lists is introduced, so
that they can be iterated over and accessed via publ->scope as
an index where convenient.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This is done so that it can be reused with differing publication
lists, instead of being hard coded to the cluster publicaton list.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
There is currently a single list that is containing both cluster-scope and
zone-scope publications, and the list count is a separate free floating
variable. Create a struct to bind the count to the list, and to pave
the way for factoring out the publications into zone/cluster/node scope.
The current "publ_root" most matches what will be the cluster scope
list, so it is named accordingly in this commit.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Use of "unsigned int" is preferred to bare "unsigned" in net tree.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimizes routines that send payload messages so that they no longer
update the "originating node" and "originating port" fields of the
outgoing message header template, since these fields are initialized
when the sending port is created and never change thereafter. Also
optimizes the routine which updates the message header template when
a connection to a port is established, for the same reason.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Removes code that updated the "previous node" field of an out-going
message over TIPC's links. Such updating is unnecessary since the
removal of the prototype multi-cluster capability means that all
outgoing messages are generated locally and already have this field
populated correctly.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Converts a non-trivial routine from inline to non-inline form
to avoid bloating the TIPC code base with 6 copies of its body.
This change is essentially cosmetic, and doesn't change existing
TIPC behavior.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Removes all references to the global variable that records whether
TIPC is running in "single node" mode or "network" mode, since this
information can be easily deduced from the global variable that
records TIPC's network address. (i.e. a non-zero network address
means that TIPC is running in network mode.)
The changes made update most existing mode-based checks to use the
network address global variable. A few checks that are no longer
needed are removed entirely, along with any associated code lying on
non-executable control paths.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Removes all references to TIPC's "not running" mode, since the
removal of support for the native API means that there is no longer
any way to interact with TIPC if it has not been initialized.
The changes made consist of removing mode-based checks that are no
longer needed, along with any associated code lying on non-executable
control paths.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Restores name table translation using a non-zero domain that is
"out of scope", which was broken by an earlier commit
(5d9c54c1e9). Comments have now been
added to the name table translation routine to make it clear that
there are actually three possible outcomes to a translation request
(found/not found/deferred), rather than just two (found/not found).
Note that a straightforward revert of the earlier commit is not
possible, as other changes to the name table translation logic
have occurred since the incorrect optimization was made.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Optimizes processing done when contact with a neighboring node is
established to avoid recording the current state of outgoing broadcast
messages if the neighboring node isn't a valid broadcast link destination,
since this state information isn't needed for such nodes.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates a block of comments that describe how routing table updates
are to be handled. These comments no longer apply following the removal
of TIPC's prototype multi-cluster support.
Note that these changes are essentially cosmetic in nature, and have
no impact on the actual operation of TIPC.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Gets rid of two inlined routines that simply call existing sk_buff
manipulation routines, since there is no longer any extra processing
done by the helper routines.
Note that these changes are essentially cosmetic in nature, and have
no impact on the actual operation of TIPC.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Relocates information about the size of TIPC's node table index and
its associated hash function, since only node subsystem routines need
to have access to this information.
Note that these changes are essentially cosmetic in nature, and have
no impact on the actual operation of TIPC.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Simplifies a comparison operation to eliminate a useless test that
checks if an unsigned value is less than zero.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This "shortform" is actually longer than typing out what it is really
trying to do, and just makes reading the code more difficult, so
lets simply shoot it in the head.
In the case of log.c - the comparison is on a u32, so we can drop the
check for < 0 at the same time.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Adds a new check to TIPC's name table logic to reject any attempt to
create a new name publication that is identical to an existing one.
(Such an attempt will never happen under normal circumstances, but
could arise if another network node malfunctions and issues a duplicate
name publication message.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Streamlines the logic that prevents an application from binding a
reserved TIPC name type to a port by moving the check to the code
that handles a socket bind() operation. This allows internal TIPC
subsystems to bind a reserved name without having to set an atomic
flag to gain permission to use such a name. (This simplification is
now possible due to the elimination of support for TIPC's native API.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates a check in the processing of TIPC messages arriving from
off node that ensures the message is destined for this node, since this
check duplicates an earlier check. (The check would be necessary if TIPC
needed to be able to route incoming messages to another node, but the
elimination of multi-cluster support means that this never happens and
all incoming messages are consumed by the receiving node.)
Note: This change involves the elimination of a single "if" statement
with a large "then" clause; consequently, a significant number of lines
end up getting re-indented. In addition, a simple message header access
routine that is no longer referenced is eliminated. However, the only
functional change is the elimination of the single check described above.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Utilizes the new "node signature" field in neighbor discovery messages
to ensure that all links TIPC associates with a given <Z.C.N> network
address belong to the same neighboring node. (Previously, TIPC could not
tell if link setup requests arriving on different interfaces were from
the same node or from two different nodes that has mistakenly been assigned
the same network address.)
The revised algorithm for detecting a duplicate node considers both the
node signature and the network interface adddress specified in a request
message when deciding how to respond to a link setup request. This prevents
false alarms that might otherwise arise during normal network operation
under the following scenarios:
a) A neighboring node reboots. (The node's signature changes, but the
network interface address remains unchanged.)
b) A neighboring node's network interface is replaced. (The node's signature
remains unchanged, but the network interface address changes.)
c) A neighboring node is completely replaced. (The node's signature and
network interface address both change.)
The algorithm also handles cases in which a node reboots and re-establishes
its links to TIPC (or begins re-establishing those links) before TIPC
detects that it is using a new node signature. In such cases of "delayed
rediscovery" TIPC simply accepts the new signature without disrupting
communication that is already underway over the links.
Thanks to Laser [gotolaser@gmail.com] for his contributions to the
development of this enhancement.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Adds support for the new "node signature" in neighbor discovery messages,
which is a 16 bit identifier chosen randomly when TIPC is initialized.
This field makes it possible for nodes receiving a neighbor discovery
message to detect if multiple neighboring nodes are using the same network
address (i.e. <Z.C.N>), even when the messages are arriving on different
interfaces.
This first phase of node signature support creates the signature,
incorporates it into outgoing neighbor discovery messages, and tracks
the signature used by valid neighbors. An upcoming patch builds on this
foundation to implement the improved duplicate neighbor detection checking.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies message rejection logic so that TIPC doesn't attempt to
send a FIN message to the rejecting port if it is known in advance
that there is no such message because the rejecting port doesn't exist.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Removes code that alters the publication key of a name table entry
that is being forcibly purged from TIPC's name table after contact
with the publishing node has been lost.
Current TIPC ensures that all defunct names are purged before
re-establishing contact with a failed node. There used to be a risk
that the publication might be accidentally deleted because it might be
re-added to the name table before the purge operation was completed.
But now there is no longer a need to ensure that the new key is different
than the old one.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies broadcast link so that an incoming fragmented message is not
lost if reassembly cannot begin because there currently is no buffer
big enough to hold the entire reassembled message. The broadcast link
now ignores the first fragment completely, which causes the sending node
to retransmit the first fragment so that reassembly can be re-attempted.
Previously, the sender would have had no reason to retransmit the 1st
fragment, so we would never have a chance to re-try the allocation.
To do this cleanly without duplicaton, a new bclink_accept_pkt()
function is introduced.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies unicast link endpoint logic so an incoming fragmented message
is not lost if reassembly cannot begin because there is no buffer big
enough to hold the entire reassembled message. The link endpoint now
ignores the first fragment completely, which causes the sending node to
retransmit the first fragment so that reassembly can be re-attempted.
Previously, the sender would have had no reason to retransmit the 1st
fragment, so we would never have a chance to re-try the allocation.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Eliminates support for the broadcast tag field, which is no longer
used by broadcast link NACK messages.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Completely redesigns broadcast link ACK and NACK mechanisms to prevent
spurious retransmit requests in dual LAN networks, and to prevent the
broadcast link from stalling due to the failure of a receiving node to
acknowledge receiving a broadcast message or request its retransmission.
Note: These changes only impact the timing of when ACK and NACK messages
are sent, and not the basic broadcast link protocol itself, so inter-
operability with nodes using the "classic" algorithms is maintained.
The revised algorithms are as follows:
1) An explicit ACK message is still sent after receiving 16 in-sequence
messages, and implicit ACK information continues to be carried in other
unicast link message headers (including link state messages). However,
the timing of explicit ACKs is now based on the receiving node's absolute
network address rather than its relative network address to ensure that
the failure of another node does not delay the ACK beyond its 16 message
target.
2) A NACK message is now typically sent only when a message gap persists
for two consecutive incoming link state messages; this ensures that a
suspected gap is not confirmed until both LANs in a dual LAN network have
had an opportunity to deliver the message, thereby preventing spurious NACKs.
A NACK message can also be generated by the arrival of a single link state
message, if the deferred queue is so big that the current message gap
cannot be the result of "normal" mis-ordering due to the use of dual LANs
(or one LAN using a bonded interface). Since link state messages typically
arrive at different nodes at different times the problem of multiple nodes
issuing identical NACKs simultaneously is inherently avoided.
3) Nodes continue to "peek" at NACK messages sent by other nodes. If
another node requests retransmission of a message gap suspected (but not
yet confirmed) by the peeking node, the peeking node forgets about the
gap and does not generate a duplicate retransmit request. (If the peeking
node subsequently fails to receive the lost message, later link state
messages will cause it to rediscover and confirm the gap and send another
NACK.)
4) Message gap "equality" is now determined by the start of the gap only.
This is sufficient to deal with the most common cases of message loss,
and eliminates the need for complex end of gap computations.
5) A peeking node no longer tries to determine whether it should send a
complementary NACK, since the most common cases of message loss don't
require it to be sent. Consequently, the node no longer examines the
"broadcast tag" field of a NACK message when peeking.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensures that all attempts to update broadcast link statistics are done
only while holding the lock that protects the link's main data structures,
to prevent interference by simultaneous updates caused by messages
arriving on other interfaces.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies broadcast link so that it increments the "received duplicate
message" count if an incoming message cannot be added to the deferred
message queue because it is already present in the queue. (The aligns
broadcast link behavior with that of TIPC's unicast links.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Fixes a pair of problems in broadcast link message reception code
relating to the reclamation of the node lock after consuming an
in-sequence message.
1) Now retests to see if the sending node is still up after reclaiming
the node lock, and bails out if it is non-operational.
2) Now manipulates the node's deferred message queue only after
reclaiming the node lock, rather than using queue head pointer
information that was cached previously.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensures that any attempt to send a NACK message over TIPC's broadcast
link has exclusive access to the link's main data structures, to prevent
interference with a simultaneous attempt to send other broadcast link
traffic (such as application-generated multicast messages).
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Corrects a problem in which a link endpoint that activates as the
result of receiving a RESET/STATE sequence of link protocol messages
fails to properly record the broadcast link status information about
the node to which it is now communicating with. (The problem does
not occur with the more common RESET/ACTIVATE sequence of messages.)
The fix ensures that the broadcast link status info is updated after
the RESET message resets the link endpoint, rather than before, thereby
preventing new information from being overwritten by the reset operation.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Fix a bug that can prevent TIPC from sending broadcast messages to a node
if contact with the node is lost and then regained. The problem occurs if
the broadcast link first clears the flag indicating the node is part of the
link's distribution set (when it loses contact with the node), and later
fails to restore the flag (when contact is regained); restoration fails
if contact with the node is regained by implicit unicast link activation
triggered by the arrival of a data message, rather than explicitly by the
arrival of a link activation message.
The broadcast link now uses separate fields to track whether a node is
theoretically capable of receiving broadcast messages versus whether it is
actually part of the link's distribution set. The former member is updated
by the receipt of link protocol messages, which can occur at any time; the
latter member is updated only when contact with the node is gained or lost.
This change also permits the simplification of several conditional
expressions since the broadcast link's "supported" field can now only be
set if there are working links to the associated node.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensure that sequence number information about incoming broadcast link
messages is initialized only by the activation of the first link to a
given cluster node. Previously, a race condition allowed reset and/or
activation messages for a second link to re-initialize this sequence
number information with obsolete values. This could trigger TIPC to
request the retransmission of previously acknowledged broadcast link
messages from that node, resulting in broadcast link processing becoming
stalled if the node had already released one or more of those messages
and was unable to perform the required retransmission.
Thanks to Laser <gotolaser@gmail.com> for identifying this problem
and assisting in the development of this fix.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensures that a link endpoint discards any previously deferred link
protocol message whenever it attempts to send a new one.
Previously, it was possible for a link protocol message that was unsent
due to congestion to be transmitted after newer protocol messages had
been sent. The stale link protocol message might then cause the receiving
link endpoint to malfunction because of its outdated conent.
Thanks to Osamu Kaminuma [okaminum@avaya.com] for diagnosing the problem
and contributing a prototype patch.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Re-code the algorithm for inserting an out-of-sequence message into
a unicast or broadcast link's deferred message queue. It remains
functionally equivalent but should be easier to understand/maintain.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The addition of the "s" to indicate pluralization is intentional,
since the struct actually contains two name variants.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This changes both the struct bcbearer and struct bcbearer_pair to
have the "tipc_" prefix. Runtime behaviour is unchanged.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Make this rename so that it is consistent with the majority
of the other tipc structs and to assist in removing any
ambiguity with other similar names in other subsystems.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Make this rename so that it is consistent with the majority
of the other tipc structs and to assist in removing any
ambiguity with other similar names in other subsystems.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Make this rename so that it is consistent with the majority
of the other tipc structs and to assist in removing any
ambiguity with other similar names in other subsystems.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Make this rename so that it is consistent with the majority
of the other tipc structs and to assist in removing any
ambiguity with other similar names in other subsystems.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Give it a meaningful prefix, as suggested by DaveM, so that it
is consistent with things like struct tipc_bearer, and so it isn't
confused with anything else. This has no impact on the actual
runtime code behaviour.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Migrates the buf_seqno() helper routine from broadcast link level to
unicast link level so that it can be used both types of TIPC links.
This is a cosmetic change only, and does not affect the operation of TIPC.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Adds checks to TIPC's broadcast link so that it ignores any
acknowledgement message containing a sequence number that does not
correspond to an unacknowledged message currently in the broadcast
link's transmit queue.
This change prevents the broadcast link from becoming stalled if a
newly booted node receives stale broadcast link acknowledgement
information from another node that has not yet fully synchronized
its end of the broadcast link to reflect the current state of the
new node's end.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Adds code to release any unsent broadcast messages in the broadcast link
transmit queue if TIPC loses contact with its only neighboring node.
Previously, a broadcast link that was in the congested state would hold
on to the unsent messages, even though the messages were now undeliverable.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The two broadcast link statistics fields that are used to derive the
average length of that link's transmit queue are now updated only after
a successful attempt to send a broadcast message, since there is no need
to update these values when an unsuccessful send attempt leaves the
queue unchanged.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Adds a check to detect when an attempt is made to send a message
via the broadcast link and no neighboring nodes are currently available
to receive it. Rather than wasting effort passing the message to the
broadcast link and broadcast bearer, who will only throw it away,
TIPC now frees the message immediately and reports success (i.e. the
message has been delivered to all available destinations).
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Fixes oversight that allowed broadcast link node map to be updated without
first taking the broadcast link spinlock that protects the map. As part
of this fix the node map has been incorporated into the broadcast link
structure to make the need for such protection more evident.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Creates global variables to hold the broadcast link's pseudo-bearer and
pseudo-link structures, rather than allocating them dynamically. There
is only a single instance of each structure, and changing over to static
allocation allows elimination of code to handle the cases where dynamic
allocation was unsuccessful.
The memset in the teardown code may look like they aren't used, but
the same teardown code is run when there is a non-fatal error at
init-time, so that stale data isn't present when the user fixes the
cause of the soft error.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Gets rid of an unnecessary check in the routine that updates the port id
of a node's name publications when the node is assigned a network address,
since the routine is only invoked if the new address is different from
the existing one.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies TIPC's module unloading logic to switch itself into "single
node" mode before starting to terminate networking support. This helps
to ensure that no operations that require TIPC to be in "networking"
mode can initiate once unloading starts.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Gets rid of two pointless operations that zero out the array used to
record information about TIPC's Ethernet bearers. There is no need to
initialize the array on start up since it is a global variable that is
already zero'd out, and there is no need to zero it out on exit because
the array is never referenced again.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies Ethernet bearer disable logic to break the association between
the bearer and its device driver at the time the bearer is disabled,
rather than when the TIPC module is unloaded. This allows the array
entry used by the disabled bearer to be re-used if the same bearer (or
a different one) is subsequently enabled.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Change TIPC's shutdown code to deactivate generic networking support
before terminating Ethernet media support. The deactivation of generic
networking support causes all existing bearers to be destroyed, meaning
the Ethernet media termination routine no longer has to bother marking
them as unavailable.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Comment-only change to better explain why TIPC's configuration lock is
temporarily released while activating support for network interfaces,
and why the existing activation code doesn't require rework.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Permits run-time alteration of default link settings on a per-media
and per-bearer basis, in addition to the existing per-link basis.
The following syntax can now be used:
tipc-config -lt=<link-name|bearer-name|media-name>/<tolerance>
tipc-config -lp=<link-name|bearer-name|media-name>/<priority>
tipc-config -lw=<link-name|bearer-name|media-name>/<window>
Note that changes to the default settings for a given media type has
no effect on the default settings used by existing bearers. Similarly,
changes to default bearer settings has no effect on existing link
endpoints that utilize that interface.
Thanks to Florian Westphal <fw@strlen.de> for his contributions to
the development of this enhancement.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Adds a check to ensure that TIPC ignores an incoming neighbor discovery
message that specifies an invalid media address as its source. The check
ensures that the source address is a valid, non-broadcast address that
could legally be used by a neighboring link endpoint.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reworks TIPC's media address data structure and associated processing
routines to transfer all media-specific details of address conversion
to the associated TIPC media adaptation code. TIPC's generic bearer code
now only needs to know which media type an address is associated with
and whether or not it is a broadcast address, and totally ignores the
"value" field that contains the actual media-specific addressing info.
These changes eliminate the need for a number of endianness conversion
operations and will make it easier for TIPC to support new media types
in the future.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Enhances TIPC's Ethernet media support to provide 3 new address conversion
routines, which allow TIPC to interpret an address that is in string form
and to convert an address to and from the 20 byte format used in TIPC's
neighbor discovery messages.
These routines are pre-requisites to a follow on commit that hides all
media-specific addressing details from TIPC's generic bearer code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Enhances conversion of a media address to printable form so that an
unconvertable address will be displayed as a string of hex digits,
rather than not being displayed at all. (Also removes a pointless check
for the existence of the media-specific address conversion routine,
since the routine is not optional.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Simplifies error handling performed during media registration, since
TIPC no longer supports the dynamic addition of new media types that
are potentially error-prone. These simplifications include the following:
1) No longer check for premature registration of a new media type.
2) No longer check for negative link priority values (which was pointless
since such values are unsigned, and could cause a compiler warning).
3) No longer generate a warning describing the exact cause of any
registration failure (just warns that overall registration failed).
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Changes TIPC's list of registered media types from an array of media
structures to an array of pointers to media structures. This eliminates
the need to copy of the contents of the structure passed in during media
registration.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Streamlines the detection of an attempt to register a TIPC media structure
using an already registered name or type identifier. The revised logic now
reuses an existing routine to detect an existing name and no longer
unnecessarily manipulates the media type counter during an unsuccessful
registration attempt.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Speeds up the registration of TIPC media types by passing in a structure
containing the required information, rather than by passing in the various
fields describing the media type individually.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Permits a Linux container to use TIPC sockets even when it has its own
network namespace defined by removing the check that prohibits such use.
This makes it possible for users who wish to isolate their container
network traffic from normal network traffic to utilize TIPC.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
We can use vzalloc() helper now instead of __vmalloc() trick
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These files are non modular, but need to export symbols using
the macros now living in export.h -- call out the include so
that things won't break when we remove the implicit presence
of module.h from everywhere.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
With calls to modular infrastructure, these files really
needs the full module.h header. Call it out so some of the
cleanups of implicit and unrequired includes elsewhere can be
cleaned up.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Elimintes prototype link event tracking functionality that has never
been fleshed out and doesn't do anything useful at the current time.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminate the "event_cb" member from TIPC's "subscription" structure
since the function pointer it holds always points to subscr_send_event().
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies the proto_ops structure used by TIPC DGRAM and RDM sockets
so that calls to listen() and accept() are handled by existing kernel
"unsupported operation" routines, and eliminates the related checks
in the listen and accept routines used by SEQPACKET and STREAM sockets
that are no longer needed.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Adds support for the SO_SNDTIMEO socket option. (This complements the
existing support for SO_RCVTIMEO that is already present.)
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies the initial transfer of name table entries to a new neighboring
node so that the messages are enqueued as a unit, rather than individually.
The revised algorithm now locates the link carrying the message only once,
and eliminates unnecessary checks for link congestion, message fragmentation,
and message bundling that are not required when sending these messages.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Functions like this are called using unsigned longs from
function pointers. In this case, the function is passed in
a node which is normally internally treated as a u32 by TIPC.
Rather than add more casts into this function in the future
for each added use of node within, move the cast to a single
place on a local.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reduces the maximum size of messages sent during the initial exchange
of name table information between two nodes to be no larger than the
MTU of the first link established between the nodes. This ensures that
messages will never need to be fragmented, which would add unnecessary
overhead to the name table synchronization mechanism.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reduces the number of bearers a node can support to 2, which can use
identical or non-identical media. This change won't impact users,
since they are currently limited to a maximum of 2 Ethernet bearers,
and will save memory by eliminating a number of unused entries in
TIPC's media and bearer arrays.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Removes obsolete code that searches for an Ethernet bearer structure entry
to use for a newly enabled bearer, since this search is now performed
at the start of the enabling algorithm.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensures that the device list lock is held while trying to locate
the Ethernet device used by a newly enabled bearer, so that the
addition or removal of a device does not cause problems.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Enhances TIPC to ensure that a node that loses contact with a
neighboring node does not allow contact to be re-established until
it sees that its peer has also recognized the loss of contact.
Previously, nodes that were connected by two or more links could
encounter a situation in which node A would lose contact with node B
on all of its links, purge its name table of names published by B,
and then fail to repopulate those names once contact with B was restored.
This would happen because B was able to re-establish one or more links
so quickly that it never reached a point where it had no links to A --
meaning that B never saw a loss of contact with A, and consequently
didn't re-publish its names to A.
This problem is now prevented by enhancing the cleanup done by TIPC
following a loss of contact with a neighboring node to ensure that
node A ignores all messages sent by B until it receives a LINK_PROTOCOL
message that indicates B has lost contact with A, thereby preventing
the (re)establishment of links between the nodes. The loss of contact
is recognized when a RESET or ACTIVATE message is received that has
a "redundant link exists" field of 0, indicating that B's sending link
endpoint is in a reset state and that B has no other working links.
Additionally, TIPC now suppresses the sending of (most) link protocol
messages to a neighboring node while it is cleaning up after an earlier
loss of contact with that node. This stops the peer node from prematurely
activating its link endpoint, which would prevent TIPC from later
activating its own end. TIPC still allows outgoing RESET messages to
occur during cleanup, to avoid problems if its own node recognizes
the loss of contact first and tries to notify the peer of the situation.
Finally, TIPC now recognizes an impending loss of contact with a peer node
as soon as it receives a RESET message on a working link that is the
peer's only link to the node, and ensures that the link protocol
suppression mentioned above goes into effect right away -- that is,
even before its own link endpoints have failed. This is necessary to
ensure correct operation when there are redundant links between the nodes,
since otherwise TIPC would send an ACTIVATE message upon receiving a RESET
on its first link and only begin suppressing when a RESET on its second
link was received, instead of initiating suppression with the first RESET
message as it needs to.
Note: The reworked cleanup code also eliminates a check that prevented
a link endpoint's discovery object from responding to incoming messages
while stale name table entries are being purged. This check is now
unnecessary and would have slowed down re-establishment of communication
between the nodes in some situations.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies code that disables a bearer to ensure that all of its links
are deleted, not just its uncongested links. Similarly, modifies code
that blocks a bearer to ensure that all of its links are reset, not
just its uncongested links.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Saves a socket's TIPC_CONN_TIMEOUT socket option value in its original
form (milliseconds), rather than jiffies. This ensures that the exact
value set using setsockopt() is always returned by getsockopt(), without
being subject to rounding issues introduced by a ms->jiffies->ms
conversion sequence.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates code in tipc_send_buf_fast() that handles messages
sent to a destination on the current node, since the only caller
of the routine only passes in messages destined for other nodes.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates obsolete code that handles broadcast bearer congestion when
the broadast link sends a NACK message, since the broadcast pseudo-bearer
never becomes blocked.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies TIPC's incoming broadcast packet handler to discard messages
that cannot legally be sent over the broadcast link, including:
- broadcast protocol messages that do no contain state information
- payload messages that are not named multicast messages
- any other form of message except for bundled messages, fragmented
messages, and name distribution messages.
These checks are needed to prevent TIPC from handing an unexpected
message to a routine that isn't prepared to handle it, which could
lead to incorrect processing (up to and including invalid memory
references caused by attempts to access message fields that aren't
present in the message).
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies TIPC's incoming broadcast packet handler so that it no longer
pre-reads information about the deferred packet queue, since the cached
value is unreliable once the associated node lock has been released.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies TIPC's incoming broadcast packet handler to ensure that the
node lock associated with the sender of the packet is held whenever
node-related data structure fields are accessed. The routine is also
restructured with a single exit point, making it easier to ensure
the node lock is properly released and the incoming packet is properly
disposed of.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensure that broadcast link messages that have not been acknowledged
by a newly failed node do not get an implied acknowledgement until the
failed node is removed from the broadcast link's map of reachable nodes.
Previously, a race condition allowed a new broadcast link message to be
sent after the implicit acknowledgement processing was completed, but
before the map of reachable nodes was updated, resulting in the message
having an expected acknowledgement count that required the failed node
to explicitly acknowledge the message. Since this would never occur
the new message would remain in the broadcast link's transmit queue
forever, eventually causing the link to become congested and "stall".
Delaying the implicit acknowledgement processing until after the update
of the map of reachable nodes eliminates this race condition and prevents
stalling.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Enhances cleanup of broadcast link-related information when contact
with a node is lost.
1) All broadcast link-related cleanup now occurs only if the lost node
was capable of communicating over the broadcast link.
2) Following cleanup, the lost node is marked as no longer supporting
the broadcast link, ensuring that any remaining broadcast messages
received from that node prior to the re-establishment of a normal
communication link are ignored.
Thanks to Surya [Suryanarayana.Garlapati@emerson.com] for contributing
a prototype version of this patch.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates code associated with the sending of unsent broadcast link
traffic when the broadcast pseudo-bearer becomes unblocked following a
temporary congestion situation. This code is non-executable because the
broadcast pseudo-bearer never becomes blocked [see tipc_bcbearer_send()].
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Updates the comments in the broadcast bearer send routine to more
accurately describe the processing done by the routine. Also replaces
the improper use of a TIPC payload message error status symbol (in a place
that has nothing to do with such errors) with its numeric equivalent.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Updates TIPC's broadcast link in a couple of places that were missed
during the transition from its former name ("multicast-link") to its
current name ("broadcast-link"). These changes are essentially cosmetic
and do not affect the overall operation of TIPC.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensure TIPC ignores an out-dated link reset message whose session
number predates the current session number. (Previously, TIPC only
ignored an out-date reset message whose session number was equal
to the current link session number.)
Out-dated link reset messages should not occur under normal circumstances;
however, they can be generated if a link endpoint is unable to send a
link reset message right away and queues it for later delivery, but the
queued message is not sent until after the link is established.
Thanks to Laser [gotolaser@gmail.com] for diagnosing the problem and
contributing a prototype patch.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Initializes the peer session number field of a newly created link
endpoint to an invalid value. This eliminates the remote possibility
that it will accidentally match the session number used by the peer
the first time the link is activated, and cause the link to ignore
a valid RESET message.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Sets the peer interface portion of the name of a newly created link
endpoint to "unknown". This ensures that state and statistics information
can be properly displayed during the time between the link endpoint's
creation and the time handshaking with its peer is completed.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Removes a test that ensures unicast link endpoints discard an incoming
message if it will not be consumed by the node itself and cannot be
forwarded to another node, since the preceding test already ensures that
the message is destined for this node and single-cluster TIPC no longer
performs message forwarding.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates code that increments and validates the re-route count field
of payload messages, since the elimination of multi-cluster support
means that it is no longer necessary for TIPC to forward incoming messages
to another node. (The obsolete code was incorrect anyway, since it
incorrectly incremented the re-route count field of messages that
originated on the node that forwarded the message.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simplifies the creation of connection protocol messages by eliminating
the passing of information that is no longer required, is constant,
or is contained within the port structure that is issuing the message.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies the logic that creates a connection termination payload
message so that it no longer (mis)uses a routine that creates a
connection protocol message. The revised code is now more easily
understood, and avoids setting several fields that are either not
present in payload messages or were being set more than once.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Restructures the logic used in tipc_port_recv_proto_msg() to ensure
that incoming connection protocol messages are handled properly. The
routine now uses a two-stage process that first ensures the message
applies on an existing connection and then processes the request.
This corrects a loophole that allowed a connection probe request to
be processed if it was sent to an unconnected port that had no names
bound to it.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Speeds up the creation of the FIN message that terminates a TIPC
connection. The typical peer termination message is now created by
duplicating the terminating port's standard payload message header
and adjusting the message size, importance, and error code fields,
rather than building all fields of the message from scratch. A FIN
message that is directed to the port itself is created the same way.
but also requires swapping the origin and destination address fields.
In addition to reducing the work required to create FIN messages,
these changes eliminate several instances of duplicated code,
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Performs cosmetic cleanup of the symbolic names used to specify TIPC
payload message header sizes. The revised names now more accurately
reflect the payload messages in which they can appear. In addition,
several places where these payload message symbol names were being used
to create non-payload messages have been updated to use the proper
internal message symbolic name.
No functional changes are introduced by this rework.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Gets rid of code that allows tipc_msg_init() to create a short
payload message header. This optimization is possible because
there are no longer any callers who require this capability.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates a pair of #include statements for files that are brought in
automatically by including core.h.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Gets rid of counter that records the number of times a bearer has
resumed after congestion or blocking, since the value is never
referenced anywhere.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Fixes a minor error in the title of one of the message size profiling
values printed as part of TIPC's link statistics.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Gets rid of a pair of checks to see if a name sequence entry in
TIPC's name table has an empty zone list. These checks are pointless
since the zone list can never be empty (i.e. as soon as the list
becomes empty the associated name sequence entry is deleted).
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies the main circular linked lists of publications used in TIPC's
name table to use the standard kernel linked list type. This change
simplifies the deletion of an existing publication by eliminating
the need to search up to three lists to locate the publication.
The use of standard list routines also helps improve the readability
of the name table code by make it clearer what each list operation
being performed is actually doing.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies the name table array structure that contains the name
sequence instances for a given name type so that the publication
lists associated with a given instance are stored in a dynamically
allocated structure, rather than being embedded within the array
entry itself. This change is being done for several reasons:
1) It reduces the amount of data that needs to be copied whenever
a given array is expanded or contracted to accommodate the first
publication of a new name sequence or the removal of the last
publication of an existing name sequence.
2) It reduces the amount of memory associated with array entries that
are currently unused.
3) It facilitates the upcoming conversion of the publication lists
from TIPC-specific circular lists to standard kernel lists. (Standard
lists cannot be used with the former array structure because the
relocation of array entries during array expansion and contraction
would corrupt the lists.)
Note that, aside from introducing a small amount of code to dynamically
allocate and free the structure that now holds publication list info,
this change is largely a simple renaming exercise that replaces
references to "sseq->LIST" with "sseq->info->LIST" (or "info->LIST").
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Gets rid of unnecessary masking in two routines that set TIPC message
header fields. (The msg_set_bits() routine already takes care of
masking the new value to the correct size.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Gets rid of a pair of routines that provide support for temporarily
caching the destination node for a message in the associated message
buffer's application handle, since this capability is no longer used.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Optimizes the creation of a returned payload message by duplicating
the original message and then updating the small number of fields
that need to be adjusted, rather than building the new message header
from scratch. In addition, certain operations that are not always
required are relocated so that they are only done if needed.
These optimizations also have the effect of addressing other issues
that were present previously:
1) Fixes a bug that caused the socket send routines to return the
size of the returned message, rather than the size of the sent
message, when a returnable payload message was sent to a non-existent
destination port.
2) The message header of the returned message now matches that of
the original message more closely. The header is now always the same
size as the original header, and some message header fields that
weren't being initialized in the returned message header are now
populated correctly -- namely the "d" and "s" bits, and the upper
bound of a multicast name instance (where present).
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reduces the work involved in transmitting a returned payload message
by doing only the work necessary to route such a message directly to
the specified destination port, rather than invoking the code used
to route an arbitrary message to an arbitrary destination.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Introduces an internal sanity check to ensure that the only undeliverable
messages TIPC attempts to return to their origin are application payload
messages.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies the routine that handles the rejection of payload messages
so that it has a single exit point that frees up the rejected message,
thereby eliminating some duplicated code.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates a TIPC-specific assert() macro that is no longer used.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies the existing broadcast link sanity check that detects an
attempt to send a message off-node when there are no available
destinations so that it no longer causes a kernel panic; instead,
the check now issues a warning and stack trace and then returns
without sending the message anywhere.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Revises the algorithm governing the sending of link request messages
to take into account the number of nodes each bearer is currently in
contact with, and to ensure more rapid rediscovery of neighboring nodes
if a bearer fails and then recovers.
The discovery object now sends requests at least once a second if it
is not in contact with any other nodes, and at least once a minute if
it has at least one neighbor; if contact with the only neighbor is
lost, the object immediately reverts to its initial rapid-fire search
timing to accelerate the rediscovery process.
In addition, the discovery object now stops issuing link request
messages if it is in contact with the only neighboring node it is
configured to communicate with, since further searching is unnecessary.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Augments TIPC's discovery object to track the number of neighboring nodes
having an active link to the associated bearer.
This means tipc_disc_update_link_req() becomes either one of:
tipc_disc_add_dest()
or:
tipc_disc_remove_dest()
depending on the code flow direction of things.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Augments TIPC's discovery object to send its initial neighbor discovery
request message as soon as the associated bearer is created, rather than
waiting for its first periodic timeout to occur, thereby speeding up the
discovery process. Also adds a check to suppress the initial request or
subsequent requests if the bearer is blocked at the time the request is
scheduled for transmission.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies bearer creation and deletion code to improve handling of
scenarios when a neighbor discovery object cannot be created. The
creation routine now aborts the creation of a bearer if its discovery
object cannot be created, and deletes the newly created bearer, rather
than failing quietly and leaving an unusable bearer hanging around.
Since the exit via the goto label really isn't a definitive failure
in all cases, relabel it appropriately.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Create a helper routine to enqueue a chain of sk_buffs to a link's
transmit queue. It improves readability and the new function is
anticipated to be used more than just once in the future as well.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Rework TIPC's message sending routines to take advantage of the total
amount of data value passed to it by the kernel socket infrastructure.
This change eliminates the need for TIPC to compute the size of outgoing
messages itself, as well as the check for an oversize message in
tipc_msg_build(). In addition, this change warrants an explanation:
- res = send_packet(NULL, sock, &my_msg, 0);
+ res = send_packet(NULL, sock, &my_msg, bytes_to_send);
Previously, the final argument to send_packet() was ignored (since the
amount of data being sent was recalculated by a lower-level routine)
and we could just pass in a dummy value (0). Now that the
recalculation is being eliminated, the argument value being passed to
send_packet() is significant and we have to supply the actual amount
of data we want to send.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Adds checks to TIPC's socket send routines to promptly detect and
abort attempts to send more than 66,000 bytes in a single TIPC
message or more than 2**31-1 bytes in a single TIPC byte stream request.
In addition, this ensures that the number of iovecs in a send request
does not exceed the limits of a standard integer variable.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Enhances existing checks on the discovery domain associated with a TIPC
bearer. A bearer can no longer be configured to accept links from itself
only (which would be pointless), or to nodes outside its own cluster
(since multi-cluster support has now been removed from TIPC). Also, the
neighbor discovery routine now validates link setup requests against the
configured discovery domain for the bearer, rather than simply ensuring
the requesting node belongs to the node's own cluster.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This allows them to be available for easy re-use in other places
and avoids trivial mistakes caused by "count the f's and 0's".
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies a TIPC send routine that did not discard the outgoing sk_buff
if it was not transmitted because of link congestion; this eliminates
the potential for buffer leakage in the many callers who did not clean up
the unsent buffer. (The two routines that previously did discard the unsent
buffer have been updated to eliminate their now-redundant clean up.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Sets the destination node field of an incoming multicast message
to the receiving node's network address before handing off the message
to each receiving port. This ensures that, in the event the destination
port returns the message to the sender, the sender can identify which
node the destination port belonged to.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Set the destination node and destination port fields of an outgoing
multicast message header to zero; this is necessary to ensure that
the receiving node can route the message properly if it was packed
into a bundle due to link congestion. (Previously, there was a chance
that the receiving node would send the unbundled message to a random
node & port, rather than processing the message itself.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensures that all outgoing data messages have the "name lookup scope"
field of their header set correctly; that is, named multicast messages
now specify cluster-wide name lookup, while messages not using TIPC
naming zero out the lookup field. (Previously, the lookup scope specified
for these types of messages was inherited from the last message sent
by the sending port.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Modifies the routine that fragments an existing message buffer to
use similar logic to that used when generating fragments from an iovec.
The routine now creates a complete chain of fragments and adds them to
the link transmit queue as a unit, so that the link sends all fragments
or none; this prevents the incomplete transmission of a fragmented
message that might otherwise result because of link congestion or
memory exhaustion. This change also ensures that the counter recording
the number of fragmented messages sent by the link is now incremented
only if the message is actually sent.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates code that restricts a link's counter of its fragmented
messages to a 16-bit value, since the counter value is automatically
restricted to this range when it is written into the message header.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates code that sets the link selector field in the header of
fragmented messages, since this information is never referenced.
(The unnecessary initialization was harmless as it was over-written
by the fragmented message identifier value before the fragments were
transmitted.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Eliminates optional code used to test TIPC's ability to recover
from lost broadcast messages. This code duplicates functionality
already provided by the network stack's QoS option "network emulator".
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Half of the #define entries in msg.h were down at the bottom
of the header, instead of up at the top before any of the static
inlines etc. Relocate them up to the top, to be consistent with
the other normal linux header file layout conventions.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>