This pvrusb2 change is in support of an existing feature used to help
identify and locate newer vendor supplied firmware. This change makes
the feature work for the newer larger firmware size.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
New FX2 firmware from Hauppauge is no longer 8KB in size - it's 16KB.
This is true for HVR-1950 and HVR-1900 devices. Without this change,
new pvrusb2 users with that hardware are unable to use the driver
(because the CD shipped with the hardware only has the 16KB firmware).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new hardware design applied for this cards.
Silicon Labs C8051F300 microcontroller is used for LNB power control.
It connected to cx23885 GPIO pins:
GPIO0 - P0.3 data
GPIO1 - P0.2 reset
GPIO2 - P0.1 clk
GPIO3 - P0.0 busy
Tevii S470 based on Montage Technology M88TS2020 digital satellite tuner
and M88DS3000 advanced DVB-S/S2 demodulator.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix this trivial compile warning:
v4l/atbm8830.c:164: warning: 'set_agc_config' defined but not used
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx18 av core implemented an init call for no good reason. It's now
turned into an internal function.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The I2C adapter ID is actually depends on Board and may vary, Davinci
uses id=1, but in case of AM3517 id=3.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Avoid legacy IR I2C probing for PVR-150, PVR-500, and PVR-350 cards. This
still probes, but restricts the possbile addresses probed per card.
Also removed legacy probe addresses for the KNC and PixelView cards which are
not supported by ivtv as far as I know.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change creates per cx18 instances of IR_i2c_init_data for handing over
initialization data to ir-kbd-i2c, since that module wants non-const data
even though it never modifies the data.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add explicit support for the AVerTV M116 for use with the ir-kbd-i2c module.
This also eases future support for other AVerMedia ivtv boards with the same
microcontroller program at I2C address 0x40.
This is a reworked version of an earlier patch that was...
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This avoids collisions of legacy IR controller probing with known I2C devices
in the card definitions in ivtv-cards.c. I2C driver modules for device listed
explicitly in a card definition should always take precedence over a probe
guessing where and IR controller may be.
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a module parameter to adjust I2C SCL clock period per board. This allows
some experimental fine tuning by end users to overcome quirky I2C device
problems.
Reported-by: "Aleksandr V. Piskunov" <aleksandr.v.piskunov@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Aleksandr V. Piskunov <alexandr.v.piskunov@gmail.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update the incoming MDL's buffers' bytesused and sync the buffers for the cpu
in one pass instead of two.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The encoder was not honoring the MDL size sent in DE_SET_MDL mailbox commands.
This change adjusts the size of the last buffer in an MDL, as reported to the
firmware, so that the encoder will send the exact amount of bytes we specify
per MDL transfer. This eliminates tearing in YUV playback when using
non-default YUV buffer sizes.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix YUV capture such that the encoder will pass one frame per transfer. This
will allow the application to maintain frame alignment when a transfer from
the encoder is missed due to high system latency in service the CX23418 IRQ.
Also force YUV buffer sizes to be specified in multiples of 33.75 kB, the
smalled amount of buffer sizes need to store a complete set of HM12 4:2:0
macroblocks specifying 32 lines of the frame. A full 60Hz/525 line
screen requires 15 * 33.75 kB per frame and a full 50Hz/625 line screen
requires 18 * 33.75 kB per frame so the default buffer size is 3 * 33.75 kB,
requiring exactly 5 or 6 buffers per MDL respectively. The bytes needed per
frame and hence MDL need not be the bytes in an integer number of buffers.
However, if frame artifacts are seen with scaled screen sizes, the YUV buffer
size can be set 34 kB (33.75 kB) to get rid of the artifacts at the cost of more
copies between the kernel and userspace.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a Memory Descriptor List (MDL) layer to buffer handling to implement
scatter-gather I/O. Currently there is still only 1 buffer per MDL.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename type in anticipation of implementing a struct cx18_mdl type that
actually keeps track of a memory descriptor list.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- the ov772x brightness was not setteble (fixed by M. Thrun)
- the set_frame_rate function does not work for ov965x
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For whatever reason, the device structure pointer to
videobuf_queue_vmalloc_init is typed "void *", even though it's passed
right through to videobuf_queue_core_init(), which expects a struct
device pointer. The other videobuf implementations use struct device *;
I think vmalloc should too.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The return value may be used uninitialized when the size parameter
happens to be 0.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use strlcat() to append a string to the previously created first part.
The semantic match that finds this kind of problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression dev;
expression phys;
expression str;
expression size;
@@
usb_make_path(dev, phys, size);
- strlcpy(phys, str, size);
+ strlcat(phys, str, size);
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
