Otherwise we won't run correctly on systems that require this for larger
data transfers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the case of no-match, return -EINVAL instead of 0.
Since we assign i to ret in the for loop, ret always less than
ARRAY_SIZE(clk_map_table). Thus remove the boundary checking for ret.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update lm49453_reg_defs values as per LM49453 HW revision-B
Signed-off-by: M R Swami Reddy <mr.swami.reddy@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The FLL source constants were numbered as a simple enumeration but were
being used in the code as direct values to be written to the registers.
Renumber the constants to reflect the usage.
Reported-by: Ryo Tsutsui <Ryo.Tsutsui@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
ARIZONA_AIF1_RATE_MASK is 0x7800 /* AIF1_RATE - [14:11] */
Thus we need left shift ARIZONA_AIF1_RATE_SHIFT when setting aif1 rate.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The mode variable is either 0 or 1.
To update mode setting, the mask should be BIT(0) rather than BIT(1).
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Omair M. Abdullah <omair.m.abdullah@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
sgtl5000 microphone gain only has 2 bits of resolution, so maximum value is 3.
From Eric Nelson:
"We also found that for the microphones we have here (commodity PC boom mics) a
default value of 2 for the gain gives the best results."
So change the default microphone gain as well.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the defines in wm2200.h:
/*
* R1284 (0x504) - Audio IF 1_5
*/
We should not left shift 1 bit for fmt_val when setting dai format.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Both the mask and mode settings are wrong in current code.
According to the datasheet:
S2PCFG0 (0x0A)
BIT[3:1] DATA_FORMAT
serial interface protocol format:
000: left Justified
001: I2S (default)
010: right justified
100: PCM no delay
101: PCM delay
111: DSP
Thus fixes the defines for LEFT_J_DATA_FORMAT, I2S_DATA_FORMAT, and
RIGHT_J_DATA_FORMAT.
Also adds define for DATA_FORMAT_MSK.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Since VSP only has one power bit, only provide one DAPM widget.
Signed-off-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add power down delays between setting PDN and MCLKDIS for spk amp, spklo amp, and ear amp.
Signed-off-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The 'addr' field of the sigma_action struct is stored as big endian in the
firmware file.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
