By default no control events are sent to the application that caused the
control value or flags change (i.e. the control(s) passed to VIDIOC_S_CTRL
or VIDIOC_S_EXT_CTRLS). But if a change in one control causes a change in
another control that was not part of the control(s) in VIDIOC_S_CTRL or
S_EXT_CTRLS, then the application should be notified.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new values were never copied to userspace due to this copy and paste
error. This was introduced during the rewrite of this part of the code in
commit 3219f8a362640b7e4b7e2187b1094c4e46d85aa0.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove unused pwc-ioctl.h (the copy in include/media is used everywhere)
Remove almost empty pwc-uncompress.h, move single define to pwc.h
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes the API for this:
1) v4l2 spec compliant
2) match that of the UVC Logitech QuickCam Sphere models
For now this operates in parellel to the sysfs interface for this, but the
intend is to deprecate the sysfs interface and remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also remove all the converting from native range to 0-65535 and back
that was going on. This is no longer needed now that we no longer support
v4l1.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow multiple opens of the /dev/video node so that control panel apps
can be open to-gether with streaming apps.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Doing a bunch of initialization every time /dev/video is opened, and thus
for example when the udev rules probe for capabilities makes no sense,
do it at driver load, resp. stream start instead.
This is a preparation patch for allowing multiple opens of the /dev/video
node.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
as vcinterface must be set before calling pwc_camera_power()
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Having 2 ways of tracking disconnection is too much, remove both and
instead simply set pdev->udev to NULL on disconnect. Also check for
pdev->udev being NULL in all possible entry paths.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Looking at the pwc buffer management code has made it clear to me it needed
some serious fixing. Not only was there a ton of code duplication even
internally to pwc (read and mmap wait for frame code was duplicated), the
code also was outright buggy. With the worst offender being dqbuf, which
just round robin returned all the mmap buffers, without paying any attention
to them being queued by the app with qbuf or not. And qbuf itself was a noop.
So I set out to fix this and already had some cleanups in place when
I read Jonathan Corbet's lwn article on videobuf2, this inspired me to just
rip out the buffer management code and replace it with videobuf2, greatly
reducing the amount of code, and fixing all bugs in one go:
Many thanks to Jonathan for the timely article on this !
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The chances if any of these becoming NULL magically are 0% And if they
do become NULL oopsing is the right thing to do (so that the user logs a
bug with the kernel rather then with whatever app he was using).
Returning EFAULT to userspace should only be done when userspace supplies
a bad address, not on driver bugs / hw issues, so in the few cases where the
check is not bogus return something else.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just like in userspace strncpy does not guarantee 0 termination. Use strlcpy
instead which does guarantee 0 termination.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't issue a stream stop to the camera at the end of sd_start, this fixes
streaming with this particular model.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Based on the old v4l1 camera by Jeroen Vreeken driver which recently got
removed from the kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reset image and image_len to NULL/0 on LAST_PACKET when we're in discard
frame mode, just like we do when not discarding the current frame.
The new se401 driver uses image_len for SOF/EOF detection and thus depends on
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the webcam 041e:405f, the LED is inverted.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sensor of some webcams could not be detected due to timing problems
in sensor register reading. This patch adds bridge register readings
before sensor register reading.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab wrote:
> I'm validating if all drivers are behaving equally with respect to the
> error codes returned to userspace, and double-checking with the API.
>
> On almost all places, -EFAULT code is used only to indicate when
> copy_from_user/copy_to_user fails. However, firedtv uses a lot of
> -EFAULT, where it seems to me that other error codes should be used
> instead (like -EIO for bus transfer errors and -EINVAL/-ERANGE for
> invalid/out of range parameters).
This concerns only the CI (CAM) related code of firedtv of which I know
little. Let's just pass through the error returns of lower level I/O
code where applicable, and -EACCES (permission denied) when a seemingly
valid but negative FCP response or an unknown-to-firedtv CA message is
received.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Henrik Kurelid <henrik@kurelid.se>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those drivers are not relying at the V4L2 core to handle the ioctl's.
So, we need to manually patch them every time a change goes to the
core.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-By: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, -EINVAL is used to return either when an IOCTL is not
implemented, or if the ioctl was not implemented.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move generic stuff into gen-errors.xml, and remove them from
DVB API. While here, removes two bogus error codes that aren't
supported or used on Linux: EINTERNAL and ENOSIGNAL.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When a device (or their PCI structs) are not found, the error should
be -ENODEV. -EFAULT is reserved for errors while copying arguments
from/to userspace.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove generic errors from ioctl() descriptions. For other ioctl's,
there's no generic section. So, just keep whatever is there.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove generic errors from ioctl() descriptions. For other ioctl's,
there's no generic section. So, just keep whatever is there.
Also remove the EINTERNAL error code, as no DVB driver returns
it, and this error code is not defined on POSIX or on Linux.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just like the V4L, MC and LIRC API's, point to the generic error
chapter for ioctl's. This will allow moving generic error codes
to just one place inside all media API's.
A latter patch will remove the generic errors from each specific
ioctl.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
data from/to userspace. Don't mix it with I2C bus error (-EIO).
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a reference for the generic error code chapter to LIRC ioctl
description.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L ioctl function descripton also has a generic error chapter.
Remove it, as it is now obsoleted by a general, multi-API generic
error descriptions.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The EBUSY is already described as a generic error condition, with a
similar text.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having their own generic error codes at the MC API, move
its section to the generic one and be sure that all media ioctl's
will point to it.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Be sure that all VIDIOC_* ioctl are using the return error macro, and
aren't specifying generic error codes internally.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several errors reported by V4L that aren't described.
They can occur on almost all ioctl's. Instead of adding them
into each ioctl, create a new chapter.
For V4L, the new chapter will automatically be listed on all
places, as there's a macro used everywhere there.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Scatter/gather DMA mode works nicely on this platform and is clearly the
best way of doing things.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The core Marvell camera driver can now do scatter/gather DMA on controllers
which support that functionality.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Normally no control events will go to the filehandle that called the
VIDIOC_S_CTRL/VIDIOC_S_EXT_CTRLS ioctls. This is to prevent a feedback
loop.
This can now be overridden by setting the new V4L2_EVENT_SUB_FL_ALLOW_FEEDBACK
flag.
Based on suggestions from Mauro Carvalho Chehab <mchehab@redhat.com> and
Laurent Pinchart <laurent.pinchart@ideasonboard.com>.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It's getting confusing who is linking to what, so add an overview at
the start of the header.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Starting with v3.1 the V4L2 API provides certain guarantees with respect to
events. Document these.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil
Hans de Goede
Jean-François Moine
Stefan Richter
Mauro Carvalho Chehab
Jonathan Corbet