The smatch utility reports a possible leak:
smatch warnings:
drivers/clocksource/timer-atmel-pit.c:183 at91sam926x_pit_dt_init() warn: possible memory leak of 'data'
Ensure data is freed before exiting with an error.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Use array_index_nospec() to sanitize i with respect to speculation.
Note that the user doesn't control i directly, but can make it out
of bounds by not finding a threshold in the array.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[add note about user control, as explained by Masashi]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current netpoll implementation in the bnxt_en driver has problems
that may miss TX completion events. bnxt_poll_work() in effect is
only handling at most 1 TX packet before exiting. In addition,
there may be in flight TX completions that ->poll() may miss even
after we fix bnxt_poll_work() to handle all visible TX completions.
netpoll may not call ->poll() again and HW may not generate IRQ
because the driver does not ARM the IRQ when the budget (0 for netpoll)
is reached.
We fix it by handling all TX completions and to always ARM the IRQ
when we exit ->poll() with 0 budget.
Also, the logic to ACK the completion ring in case it is almost filled
with TX completions need to be adjusted to take care of the 0 budget
case, as discussed with Eric Dumazet <edumazet@google.com>
Reported-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Song Liu <songliubraving@fb.com>
Tested-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When add vxlan ttl inherit support, I forgot to fill it when dump
vlxan info. Fix it now.
Fixes: 72f6d71e49 ("vxlan: add ttl inherit support")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A HWMON device is only registered is the SFP module supports the
diagnostic page and is complient to SFF8472. Don't unconditionally
unregister the hwmon device when the SFP module is remove, otherwise
we access data structures which don't exist.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: 1323061a01 ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:1713:25: warning: implicit
conversion from enumeration type 'enum tcp_ip_version' to different
enumeration type 'enum qed_tcp_ip_version' [-Wenum-conversion]
cm_info->ip_version = TCP_IPV4;
~ ^~~~~~~~
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:1733:25: warning: implicit
conversion from enumeration type 'enum tcp_ip_version' to different
enumeration type 'enum qed_tcp_ip_version' [-Wenum-conversion]
cm_info->ip_version = TCP_IPV6;
~ ^~~~~~~~
2 warnings generated.
Use the appropriate values from the expected type, qed_tcp_ip_version:
TCP_IPV4 = QED_TCP_IPV4 = 0
TCP_IPV6 = QED_TCP_IPV6 = 1
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when a constant is used in a boolean context as it thinks a
bitwise operation may have been intended.
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: warning: use of logical
'&&' with constant operand [-Wconstant-logical-operand]
if (!p_iov->b_pre_fp_hsi &&
^
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: note: use '&' for a
bitwise operation
if (!p_iov->b_pre_fp_hsi &&
^~
&
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: note: remove constant
to silence this warning
if (!p_iov->b_pre_fp_hsi &&
~^~
1 warning generated.
This has been here since commit 1fe614d10f ("qed: Relax VF firmware
requirements") and I am not entirely sure why since 0 isn't a special
case. Just remove the statement causing Clang to warn since it isn't
required.
Link: https://github.com/ClangBuiltLinux/linux/issues/126
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b89f04c61e ("bonding: deliver link-local packets with
skb->dev set to link that packets arrived on") changed the behavior
of how link-local-multicast packets are processed. The change in
the behavior broke some legacy use cases where these packets are
expected to arrive on bonding master device also.
This patch passes the packet to the stack with the link it arrived
on as well as passes to the bonding-master device to preserve the
legacy use case.
Fixes: b89f04c61e ("bonding: deliver link-local packets with skb->dev set to link that packets arrived on")
Reported-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/qlogic/qed/qed_roce.c:153:12: warning: implicit
conversion from enumeration type 'enum roce_mode' to different
enumeration type 'enum roce_flavor' [-Wenum-conversion]
flavor = ROCE_V2_IPV6;
~ ^~~~~~~~~~~~
drivers/net/ethernet/qlogic/qed/qed_roce.c:156:12: warning: implicit
conversion from enumeration type 'enum roce_mode' to different
enumeration type 'enum roce_flavor' [-Wenum-conversion]
flavor = MAX_ROCE_MODE;
~ ^~~~~~~~~~~~~
2 warnings generated.
Use the appropriate values from the expected type, roce_flavor:
ROCE_V2_IPV6 = RROCE_IPV6 = 2
MAX_ROCE_MODE = MAX_ROCE_FLAVOR = 3
While we're add it, ditch the local variable flavor, we can just return
the value directly from the switch statement.
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang complains when one enumerated type is implicitly converted to
another.
drivers/net/ethernet/qlogic/qed/qed_vf.c:686:6: warning: implicit
conversion from enumeration type 'enum qed_tunn_mode' to different
enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
QED_MODE_L2GENEVE_TUNN,
^~~~~~~~~~~~~~~~~~~~~~
Update mask's parameter to expect qed_tunn_mode, which is what was
intended.
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:163:25: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->vxlan.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:165:26: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->l2_gre.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:167:26: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->ip_gre.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:169:29: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->l2_geneve.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:171:29: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->ip_geneve.tun_cls = type;
~ ^~~~
5 warnings generated.
Avoid this by changing type to an int.
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in ms_to_errno array of error messages
and remove confusing "not" from the error text since the error code
refers to an uninitialized error code.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in DP_VERBOSE message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
net: phy: fix WoL handling when suspending the PHY
phy_suspend doesn't always recognize that WoL is enabled and therefore
suspends the PHY when it should not. First idea to address the issue
was to reuse checks used in mdio_bus_phy_may_suspend which check
whether relevant devices are wakeup-enabled.
Florian raised some concerns because drivers may enable wakeup even if
WoL isn't enabled (e.g. certain USB network drivers).
The new approach focuses on reducing the risk to break existing stuff.
We add a flag wol_enabled to struct net_device which is set in
ethtool_set_wol(). Then this flag is checked in phy_suspend().
This doesn't cover 100% of the cases yet (e.g. if WoL is enabled w/o
explicit configuration), but it covers the most relevant cases with
very little risk of regressions.
v2:
- Fix a typo
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Core of the problem is that phy_suspend() suspends the PHY when it
should not because of WoL. phy_suspend() checks for WoL already, but
this works only if the PHY driver handles WoL (what is rarely the case).
Typically WoL is handled by the MAC driver.
This patch uses new member wol_enabled of struct net_device as
additional criteria in the check when not to suspend the PHY because
of WoL.
Last but not least change phy_detach() to call phy_suspend() before
attached_dev is set to NULL. phy_suspend() accesses attached_dev
when checking whether the MAC driver activated WoL.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Fixes: e8cfd9d6c7 ("net: phy: call state machine synchronously in phy_stop")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flag wol_enabled to struct net_device indicating whether
Wake-on-LAN is enabled. As first user phy_suspend() will use it to
decide whether PHY can be suspended or not.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Fixes: e8cfd9d6c7 ("net: phy: call state machine synchronously in phy_stop")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Actually there's nothing wrong with the two changes marked as "Fixes",
they just revealed a problem which has been existing before.
After having switched r8169 to phylib it was reported that WoL from
shutdown doesn't work any longer (WoL from suspend isn't affected).
Reason is that during shutdown phy_disconnect()->phy_detach()->
phy_suspend() is called.
A similar issue occurs when the phylib state machine calls
phy_suspend() when handling state PHY_HALTED.
Core of the problem is that phy_suspend() suspends the PHY when it
should not due to WoL. phy_suspend() checks for WoL already, but this
works only if the PHY driver handles WoL (what is rarely the case).
Typically WoL is handled by the MAC driver.
phylib knows about this and handles it in mdio_bus_phy_may_suspend(),
but that's used only when suspending the system, not in other cases
like shutdown.
Therefore factor out the relevant check from
mdio_bus_phy_may_suspend() to a new function phy_may_suspend() and
use it in phy_suspend().
Last but not least change phy_detach() to call phy_suspend() before
attached_dev is set to NULL. phy_suspend() accesses attached_dev
when checking whether the MAC driver activated WoL.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Fixes: e8cfd9d6c7 ("net: phy: call state machine synchronously in phy_stop")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to move metrics from the dst to rt6_info moved the call
to ip6_convert_metrics from ip6_route_add to ip6_route_info_create. In
doing so it makes the call in ip6_route_info_append redundant and
actually leaks the metrics installed as part of the ip6_route_info_create.
Remove the now unnecessary call.
Fixes: d4ead6b34b ("net/ipv6: move metrics from dst to rt6_info")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the deadline scheduler is used with a zoned block device, writes
to a zone will be dispatched one at a time. This causes the warning
message:
deadline: forced dispatching is broken (nr_sorted=X), please report this
to be displayed when switching to another elevator with the legacy I/O
path while write requests to a zone are being retained in the scheduler
queue.
Prevent this message from being displayed when executing
elv_drain_elevator() for a zoned block device. __blk_drain_queue() will
loop until all writes are dispatched and completed, resulting in the
desired elevator queue drain without extensive modifications to the
deadline code itself to handle forced-dispatch calls.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Fixes: 8dc8146f9c ("deadline-iosched: Introduce zone locking support")
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
one fix to get a proper DMA configuration in place for the etnaviv
virtual device. I'm sending this as a fix, as a dma-mapping change at
the ARC architecture side during the 4.19 cycle broke etnaviv on this
platform, which gets remedied with this patch, but it also enables
ARM64.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/ea1f712bf09bf9439c6b092bf2c2bde7bb01cf5e.camel@pengutronix.de
The debounce value in device tree is in milliseconds but needs to be in
microseconds for mmc_gpiod_request_cd().
Fixes: bfd694d5e2 ("mmc: core: Add tunable delay before detecting card
after card is inserted")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
HP 6730b laptop has an ethernet NIC connected to one of the PCIe root
ports. The root ports themselves are native PCIe hotplug capable. Now,
during boot after PCI devices are scanned the BIOS triggers ACPI bus check
directly to the NIC:
ACPI: \_SB_.PCI0.RP06.NIC_: Bus check in hotplug_event()
It is not clear why it is sending bus check but regardless the ACPI hotplug
notify handler calls enable_slot() directly (instead of going through
acpiphp_check_bridge() as there is no bridge), which ends up handling
special case for non-hotplug bridges with native PCIe hotplug. This
results a crash of some kind but the reporter only sees black screen so it
is hard to figure out the exact spot and what actually happens. Based on
a few fix proposals it was tracked to crash somewhere inside
pci_assign_unassigned_bridge_resources().
In any case we should not really be in that special branch at all because
the ACPI notify happened to a slot that is not a PCI bridge (it is just a
regular PCI device).
Fix this so that we only go to that special branch if we are calling
enable_slot() for a bridge (e.g., the ACPI notification was for the
bridge).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201127
Fixes: 84c8b58ed3 ("ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug")
Reported-by: Peter Anemone <peter.anemone@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org # v4.18+
Replace "fall though" with a proper "fall through" annotation.
This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Addresses-Coverity-ID: 402013 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
In some setups restoring the BGRT logo is undesirable, allow passing
video=efifb:nobgrt on the kernel commandline to disable it.
Reported-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
OMAPFB_MEMORY_READ ioctl reads pixels from the LCD's memory and copies
them to a userspace buffer. The code has two issues:
- The user provided width and height could be large enough to overflow
the calculations
- The copy_to_user() can copy uninitialized memory to the userspace,
which might contain sensitive kernel information.
Fix these by limiting the width & height parameters, and only copying
the amount of data that we actually received from the LCD.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Jann Horn <jannh@google.com>
Cc: stable@vger.kernel.org
Cc: security@kernel.org
Cc: Will Deacon <will.deacon@arm.com>
Cc: Jann Horn <jannh@google.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
We attempt to get fences earlier in the hopes that everything will
already have fences and no callbacks will be needed. If we do succeed
in getting a fence, getting one a second time will result in a duplicate
ref with no unref. This is causing memory leaks in Vulkan applications
that create a lot of fences; playing for a few hours can, apparently,
bring down the system.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107899
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180926071703.15257-1-jason.ekstrand@intel.com
-----BEGIN PGP SIGNATURE-----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=OFJh
-----END PGP SIGNATURE-----
Merge tag 'v4.19-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into fbdev-for-next
Sync with upstream (which now contains fbdev-v4.19 changes) to
prepare a base for fbdev-v4.20 changes.
Three fixes queued up:
- Warning fix for Rockchip IOMMU where there were IRQ handlers
for offlined hardware.
- Fix for Intel VT-d because recent changes caused boot failures
on some machines because it tried to allocate to much
contiguous memory.
- Fix for AMD IOMMU to handle eMMC devices correctly that appear
as ACPI HID devices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=bwMQ
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v4.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Joerg writes:
"IOMMU Fixes for Linux v4.19-rc5
Three fixes queued up:
- Warning fix for Rockchip IOMMU where there were IRQ handlers
for offlined hardware.
- Fix for Intel VT-d because recent changes caused boot failures
on some machines because it tried to allocate to much
contiguous memory.
- Fix for AMD IOMMU to handle eMMC devices correctly that appear
as ACPI HID devices."
* tag 'iommu-fixes-v4.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Return devid as alias for ACPI HID devices
iommu/vt-d: Handle memory shortage on pasid table allocation
iommu/rockchip: Free irqs in shutdown handler
The allocation of hwsim radio identifiers uses a post-increment from 0,
so the first radio has idx 0. This idx is explicitly excluded from
multicast announcements ever since, but it is unclear why.
Drop that idx check and announce the first radio as well. This makes
userspace happy if it relies on these events.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The asynchronous destruction from a work-queue of radios tagged with
destroy-on-close may race with the owning namespace about to exit,
resulting in potential use-after-free of that namespace.
Instead of using a work-queue, move radios about to destroy to a
temporary list, which can be worked on synchronously after releasing
the lock. This should be safe to do from the netlink socket notifier,
as the namespace is guaranteed to not get released.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The cleanup of radios during namespace exit has recently been reworked
to directly delete a radio while temporarily releasing the spinlock,
fixing a race condition between the work-queue execution and namespace
exits. However, the temporary unlock allows unsafe modifications on the
iterated list, resulting in a potential crash when continuing the
iteration of additional radios.
Move radios about to destroy to a temporary list, and clean that up
after releasing the spinlock once iteration is complete.
Fixes: 8cfd36a0b5 ("mac80211_hwsim: fix use-after-free bug in hwsim_exit_net")
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use array_index_nospec() to sanitize ridx with respect to speculation.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drop @ptr from kernel-doc for function reg_query_regdb_wmm().
This function parameter was recently removed so update the
kernel-doc to match that and remove the kernel-doc warnings.
Removes 109 occurrences of this warning message:
../include/net/cfg80211.h:4869: warning: Excess function parameter 'ptr' description in 'reg_query_regdb_wmm'
Fixes: 38cb87ee47 ("cfg80211: make wmm_rule part of the reg_rule structure")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Monitor mode interfaces with the active flag are passed down to the driver.
Drivers using TXQ expect that all interfaces have allocated TXQs before
they get added.
Fixes: 79af1f8661 ("mac80211: avoid allocating TXQs that won't be used")
Cc: stable@vger.kernel.org
Reported-by: Catrinel Catrinescu <cc@80211.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ACPI HID devices do not actually have an alias for
them in the IVRS. But dev_data->alias is still used
for indexing into the IOMMU device table for devices
being handled by the IOMMU. So for ACPI HID devices,
we simply return the corresponding devid as an alias,
as parsed from IVRS table.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Fixes: 2bf9a0a127 ('iommu/amd: Add iommu support for ACPI HID devices')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In tipc_link_reset() we copy the wakeup queue to input queue using
skb_queue_splice_init(link->wakeupq, link->inputq).
This is performed without holding any locks. The lists might be
simultaneously be accessed by other cpu threads in tipc_sk_rcv(),
something leading to to random missing packets.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we detect that under lying carrier detects errors and goes down,
we reset the bearer.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused parameter from SPI6 dmas property on stm32mp157c SoC.
Fixes: dc3f8c86c1 ("ARM: dts: stm32: add SPI support on stm32mp157c")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
[olof: Without this patch, SPI6 will fall back to interrupt mode with
lower perfmance]
Signed-off-by: Olof Johansson <olof@lixom.net>
A recent commit runs tag iterator callbacks under the rcu read lock,
but existing callbacks do not satisfy the non-blocking requirement.
The commit intended to prevent an iterator from accessing a queue that's
being modified. This patch fixes the original issue by taking a queue
reference instead of reading it, which allows callbacks to make blocking
calls.
Fixes: f5bbbbe4d6 ("blk-mq: sync the update nr_hw_queues with blk_mq_queue_tag_busy_iter")
Acked-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The patch adding the infrastructure failed to actually add the symbol
declaration, oops..
Fixes: faef87723a ("dma-noncoherent: add a arch_sync_dma_for_cpu_all hook")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently add_modify_gid() for IB link layer has followong issue
in cache update path.
When GID update event occurs, core releases reference to the GID
table without updating its state and/or entry pointer.
CPU-0 CPU-1
------ -----
ib_cache_update() IPoIB ULP
add_modify_gid() [..]
put_gid_entry()
refcnt = 0, but
state = valid,
entry is valid.
(work item is not yet executed).
ipoib_create_ah()
rdma_create_ah()
rdma_get_gid_attr() <--
Tries to acquire gid_attr
which has refcnt = 0.
This is incorrect.
GID entry state and entry pointer is provides the accurate GID enty
state. Such fields must be updated with rwlock to protect against
readers and, such fields must be in sane state before refcount can drop
to zero. Otherwise above race condition can happen leading to
use-after-free situation.
Following backtrace has been observed when cache update for an IB port
is triggered while IPoIB ULP is creating an AH.
Therefore, when updating GID entry, first mark a valid entry as invalid
through state and set the barrier so that no callers can acquired
the GID entry, followed by release reference to it.
refcount_t: increment on 0; use-after-free.
WARNING: CPU: 4 PID: 29106 at lib/refcount.c:153 refcount_inc_checked+0x30/0x50
Workqueue: ib-comp-unb-wq ib_cq_poll_work [ib_core]
RIP: 0010:refcount_inc_checked+0x30/0x50
RSP: 0018:ffff8802ad36f600 EFLAGS: 00010082
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000002 RSI: 0000000000000008 RDI: ffffffff86710100
RBP: ffff8802d6e60a30 R08: ffffed005d67bf8b R09: ffffed005d67bf8b
R10: 0000000000000001 R11: ffffed005d67bf8a R12: ffff88027620cee8
R13: ffff8802d6e60988 R14: ffff8802d6e60a78 R15: 0000000000000202
FS: 0000000000000000(0000) GS:ffff8802eb200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f3ab35e5c88 CR3: 00000002ce84a000 CR4: 00000000000006e0
IPv6: ADDRCONF(NETDEV_CHANGE): ib1: link becomes ready
Call Trace:
rdma_get_gid_attr+0x220/0x310 [ib_core]
? lock_acquire+0x145/0x3a0
rdma_fill_sgid_attr+0x32c/0x470 [ib_core]
rdma_create_ah+0x89/0x160 [ib_core]
? rdma_fill_sgid_attr+0x470/0x470 [ib_core]
? ipoib_create_ah+0x52/0x260 [ib_ipoib]
ipoib_create_ah+0xf5/0x260 [ib_ipoib]
ipoib_mcast_join_complete+0xbbe/0x2540 [ib_ipoib]
Fixes: b150c3862d ("IB/core: Introduce GID entry reference counts")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
There is a copy and paste bug so we accidentally use the RX_ shift when
we're in TX_ mode.
Fixes: bb8b2062af ("fsl/qe: setup clock source for TDM mode")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
(cherry picked from commit 3cb31b634052ed458922e0c8e2b4b093d7fb60b9)
Signed-off-by: Olof Johansson <olof@lixom.net>