Currently after configuring a GPIO pin as an interrupt related pinmux
registers are changed, but there is no protection from calling
gpio_direction_*() in a badly written driver, which would cause the same
pinmux register to be reconfigured for regular input/output and this
disabling interrupt capability of the pin.
This patch addresses this issue by moving pinmux reconfiguration to
.irq_{request,release}_resources() callback of irq_chip and calling
gpio_lock_as_irq() helper to prevent reconfiguration of pin direction.
Setting up a GPIO interrupt on Samsung SoCs is a two-step operation -
in addition to trigger configuration in a dedicated register, the pinmux
must be also reconfigured to GPIO interrupt, which is a different function
than normal GPIO input, although I/O-wise they both behave in the same way
and gpio_get_value() can be used on a pin configured as IRQ as well.
Such design implies subtleties such as gpio_direction_input() not having
to fail if a pin is already configured as an interrupt nor change the
configuration to normal input. But the FLAG_USED_AS_IRQ set in gpiolib by
gpio_lock_as_irq() is only used to check that gpio_direction_output() is
not called, it's not used to prevent gpio_direction_input() to be called.
So this is not a complete solution for Samsung SoCs but it's definitely a
move in the right direction.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
[javier: use request resources instead of startup and expand commit message]
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.
Found by using regex suggested by Joe Perches.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pctldev can't be NULL at this stage so remove the check
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a cut and paste bug so we test the wrong variable. "err" is
never less than zero at this point.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On rk3288, for gpio bank 0, the registers which configure pull-up,
iomux, and drive strength don't implement the enable bits in the upper
half of the register, unlike the other gpio configuration registers,
and so the kernel must perform a read-modify-write of the register to
update a particular gpio in that bank.
The current code is actually clobbering the contents of the register,
so this fixes it by using regmap_update_bits and masking out only the
bits which require updating. In the case of bank0 on rk3288 the upper
enable bits will just get ignored, and the other configurations won't
get clobbered.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I had made last-minute changes before submitting the patch "sh-pfc: r8a7791:
add CAN pin groups"; now I'm seeing that they weren't complete: I had missed
update to the pin group names in pin[01]_groups[]. Drop the "_a" suffixes there.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A handful of driver-related changes. We've had a bunch of them going in through
other branches as well, so it's only a part of what we really have this release.
Larger pieces are:
* Removal of a now unused PWM driver for atmel
- This includes AVR32 changes that have been appropriately acked.
* Performance counter support for the arm CCN interconnect
* OMAP mailbox driver cleanups and consolidation
* PCI and SATA PHY drivers for SPEAr 13xx platforms
* Redefinition (with backwards compatibility!) of PCI DT bindings for Tegra to
better model regulators/power.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=fsP6
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"A handful of driver-related changes. We've had a bunch of them going
in through other branches as well, so it's only a part of what we
really have this release.
Larger pieces are:
- Removal of a now unused PWM driver for atmel
[ This includes AVR32 changes that have been appropriately acked ]
- Performance counter support for the arm CCN interconnect
- OMAP mailbox driver cleanups and consolidation
- PCI and SATA PHY drivers for SPEAr 13xx platforms
- Redefinition (with backwards compatibility!) of PCI DT bindings for
Tegra to better model regulators/power"
Note: this merge also fixes up the semantic conflict with the new
calling convention for devm_phy_create(), see commit f0ed817638 ("phy:
core: Let node ptr of PHY point to PHY and not of PHY provider") that
came in through Greg's USB tree.
Semantic merge patch by Stephen Rothwell <sfr@canb.auug.org.au> through
the next tree.
* tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: arm-ccn: Fix error handling at event allocation
mailbox/omap: add a parent structure for every IP instance
mailbox/omap: remove the private mailbox structure
mailbox/omap: consolidate OMAP mailbox driver
mailbox/omap: simplify the fifo assignment by using macros
mailbox/omap: remove omap_mbox_type_t from mailbox ops
mailbox/omap: remove OMAP1 mailbox driver
mailbox/omap: use devm_* interfaces
bus: ARM CCN: add PERF_EVENTS dependency
bus: ARM CCN PMU driver
PCI: spear: Remove spear13xx_pcie_remove()
PCI: spear: Fix Section mismatch compilation warning for probe()
ARM: tegra: Remove legacy PCIe power supply properties
PCI: tegra: Remove deprecated power supply properties
PCI: tegra: Implement accurate power supply scheme
ARM: SPEAr13xx: Update defconfigs
ARM: SPEAr13xx: Add pcie and miphy DT nodes
ARM: SPEAr13xx: Add bindings and dt node for misc block
ARM: SPEAr13xx: Fix static mapping table
phy: Add drivers for PCIe and SATA phy on SPEAr13xx
...
Unlike the board branch, this keeps having large sets of changes for
every release, but that's quite expected and is so far working well.
Most of this is plumbing for various device bindings and new platforms,
but there's also a bit of cleanup and code removal for things that
are moved from platform code to DT contents (some OMAP clock code in
particular).
There's also a pinctrl driver for tegra here (appropriately acked),
that's introduced this way to make it more bisectable.
I'm happy to say that there were no conflicts at all with this branch
this release, which means that changes are flowing through our tree as
expected instead of merged through driver maintainers (or at least not
done with conflicts).
There are several new boards added, and a couple of SoCs. In no particular
order:
* Rockchip RK3288 SoC support, including DTS for a dev board that they
have seeded with some community developers.
* Better support for Hardkernel Exynos4-based ODROID boards.
* CCF conversions (and dtsi contents) for several Renesas platforms.
* Gumstix Pepper (TI AM335x) board support
* TI eval board support for AM437x
* Allwinner A23 SoC, very similar to existing ones which mostly has
resulted in DT changes for support. Also includes support for an Ippo
tablet with the chipset.
* Allwinner A31 Hummingbird board support, not to be confused with the
SolidRun i.MX-based Hummingboard.
* Tegra30 Apalis board support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=xxlY
-----END PGP SIGNATURE-----
Merge tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device-tree changes from Olof Johansson:
"Unlike the board branch, this keeps having large sets of changes for
every release, but that's quite expected and is so far working well.
Most of this is plumbing for various device bindings and new
platforms, but there's also a bit of cleanup and code removal for
things that are moved from platform code to DT contents (some OMAP
clock code in particular).
There's also a pinctrl driver for tegra here (appropriately acked),
that's introduced this way to make it more bisectable.
I'm happy to say that there were no conflicts at all with this branch
this release, which means that changes are flowing through our tree as
expected instead of merged through driver maintainers (or at least not
done with conflicts).
There are several new boards added, and a couple of SoCs. In no
particular order:
- Rockchip RK3288 SoC support, including DTS for a dev board that
they have seeded with some community developers.
- Better support for Hardkernel Exynos4-based ODROID boards.
- CCF conversions (and dtsi contents) for several Renesas platforms.
- Gumstix Pepper (TI AM335x) board support
- TI eval board support for AM437x
- Allwinner A23 SoC, very similar to existing ones which mostly has
resulted in DT changes for support. Also includes support for an
Ippo tablet with the chipset.
- Allwinner A31 Hummingbird board support, not to be confused with
the SolidRun i.MX-based Hummingboard.
- Tegra30 Apalis board support"
* tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (334 commits)
ARM: dts: Enable USB host0 (EHCI) on rk3288-evb
ARM: dts: add rk3288 ehci usb devices
ARM: dts: Turn on USB host vbus on rk3288-evb
ARM: tegra: apalis t30: fix device tree compatible node
ARM: tegra: paz00: Fix some indentation inconsistencies
ARM: zynq: DT: Clarify Xilinx Zynq platform
ARM: dts: rockchip: add watchdog node
ARM: dts: rockchip: remove pinctrl setting from radxarock uart2
ARM: dts: Add missing pinctrl for uart0/1 for exynos3250
ARM: dts: Remove duplicate 'interrput-parent' property for exynos3250
ARM: dts: Add TMU dt node to monitor the temperature for exynos3250
ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250
ARM: dts: cypress,cyapa trackpad is exynos5250-Snow only
ARM: dts: max77686 is exynos5250-snow only
ARM: zynq: DT: Remove DMA from board DTs
ARM: zynq: DT: Add CAN node
ARM: EXYNOS: Add exynos5260 PMU compatible string to DT match table
ARM: dts: Add PMU DT node for exynos5260 SoC
ARM: EXYNOS: Add support for Exynos5410 PMU
ARM: dts: Add PMU to exynos5410
...
development cycle:
- Get rid of the .disable() callback from the driver callback
vtable. This callback was abused and counterintuitive since
a pin or group of pins can be said to always be in some
setting, and never really disabled. We now only enable a
certain muxing, and move between some certain muxings, we
never "disable" a mux setting.
- Some janitorial moving the MSM, Samsung and Nomadik and
drivers to their own subdirectories for a clearer view in
the subsystem. This will continue.
- Kill off the use of the return value from gpiochip_remove(),
this will be done in parallel in the GPIO subsystem and
hopefully not trigger too many unchecked return value
warnings before we get rid of this altogether.
- A huge set of changes and improvements to the Allwinner
sunxi drivers especially for their latest A23 and A31 SoCs,
and some ground work for the new sun8i platform family.
- A large set of Rockchip driver improvements adding support
for the RK3288 SoC.
- Advances in migration of older Freescale platforms to pin
control, especially i.MX1.
- Samsung and Exynos improvements.
- Support for the Qualcomm MSM8960 SoC.
- Use the gpiolib irqchip helpers for the ST SPEAr and
Intel Baytrail drivers.
- A bunch of nice janitorial work done with cppcheck.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=t1pR
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl updates from Linus Walleij:
"This is the bulk pin control changes for the v3.17 merge development
cycle:
- get rid of the .disable() callback from the driver callback vtable.
This callback was abused and counterintuitive since a pin or group
of pins can be said to always be in some setting, and never really
disabled. We now only enable a certain muxing, and move between
some certain muxings, we never "disable" a mux setting
- some janitorial moving the MSM, Samsung and Nomadik and drivers to
their own subdirectories for a clearer view in the subsystem. This
will continue
- kill off the use of the return value from gpiochip_remove(), this
will be done in parallel in the GPIO subsystem and hopefully not
trigger too many unchecked return value warnings before we get rid
of this altogether
- a huge set of changes and improvements to the Allwinner sunxi
drivers especially for their latest A23 and A31 SoCs, and some
ground work for the new sun8i platform family
- a large set of Rockchip driver improvements adding support for the
RK3288 SoC
- advances in migration of older Freescale platforms to pin control,
especially i.MX1
- Samsung and Exynos improvements
- support for the Qualcomm MSM8960 SoC
- use the gpiolib irqchip helpers for the ST SPEAr and Intel Baytrail
drivers
- a bunch of nice janitorial work done with cppcheck"
* tag 'pinctrl-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (61 commits)
pinctrl: baytrail: Convert to use gpiolib irqchip
pinctrl: sunxi: number gpio ranges starting from 0
pinctrl: sunxi: use gpiolib API to mark a GPIO used as an IRQ
pinctrl: rockchip: add drive-strength control for rk3288
pinctrl: rockchip: add separate type for rk3288
pinctrl: rockchip: set is_generic in pinconf_ops
pinctrl: msm: drop negativity check on unsigned value
pinctrl: remove all usage of gpio_remove ret val in driver/pinctl
pinctrl: qcom: Make muxing of gpio function explicit
pinctrl: nomadik: move all Nomadik drivers to subdir
pinctrl: samsung: Group all drivers in a sub-dir
sh-pfc: sh73a0: Introduce the use of devm_regulator_register
sh-pfc: Add renesas,pfc-r8a7791 to binding documentation
pinctrl: msm: move all qualcomm drivers to subdir
pinctrl: msm: Add msm8960 definitions
pinctrl: samsung: Allow pin value to be initialized using pinfunc
pinctrl: samsung: Allow grouping multiple pinmux/pinconf nodes
pinctrl: exynos: Consolidate irq_chips of GPIO and WKUP EINTs
pinctrl: samsung: Handle GPIO request and free using pinctrl helpers
pinctrl: samsung: Decouple direction setting from pinctrl
...
Instead of open-coding irqchip handling in the driver we can take advantage
of the new irqchip helpers provided by the gpiolib core.
While doing this we also make sure that we call gpiochip_irqchip_add()
after the gpiochip itself is registered as required.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl-sunxi driver originally used the pin number as the gpio
range offset. This resulted in large, bogus gpio numbers for the
new sun6i-a31-r pinctrl devices.
This patch makes the driver number the gpios ranges starting from an
offset of 0, by subtracting the pin_base number from the pin number.
This also makes the system-wide gpio number match the pin number.
Tested on sun8i with sysfs exported gpios.
This patch also changes the GPIO bindings for R_PIO:
gpios = <&r_pio B N flag>;
Where B originally was the pinbank label (L or M) counted from A,
with this patch it becomes (L or M) counted from its pinbank base (L).
Thus
gpios = <&r_pio 10 11 0>; /* PL11 */
becomes
gpios = <&r_pio 0 11 0>; /* PL11 */
IMO this is correct, as the binding shows the bank offset and pin offset
within the bank for the GPIO controller. But I'm worried it might be a
bit confusing.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When an IRQ is started on a GPIO line, mark this GPIO as IRQ in
the gpiolib so we can keep track of the usage centrally.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The rk3288 is the first Rockchip soc handling the drive strength on a per-pin
basis, while the older ones can set the drive-strength only for specific
pin-groups. Therefore limit setting the drive-strength to this soc for now.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
An upcoming pinctrl function of the rk3288 differs again from everything else,
so we'll need a separate type for it.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The rockchip pinctrl driver implements the generic pinconfig, therefore
also state this, so that the default pinconf dump functions work.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of relying on pinmux->disable(), make the gpio function an
explicit function for all pins that supports it.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds device tree bindings and a driver for the XUSB pad controller found
on Tegra114 and later. This is a prerequisites for PCIe, SATA and XUSB
drivers which are all currently being reviewed or pending for merge.
This is a separate branch in case it needs to be pulled into the pinctrl
tree to resolve conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=oUBt
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.17-xusb-padctl' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: Add XUSB pad controller support" from Thierry Reding:
Adds device tree bindings and a driver for the XUSB pad controller found
on Tegra114 and later. This is a prerequisites for PCIe, SATA and XUSB
drivers which are all currently being reviewed or pending for merge.
This is a separate branch in case it needs to be pulled into the pinctrl
tree to resolve conflicts.
* tag 'tegra-for-3.17-xusb-padctl' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
pinctrl: Add NVIDIA Tegra XUSB pad controller support
of: Add NVIDIA Tegra XUSB pad controller binding
Signed-off-by: Olof Johansson <olof@lixom.net>
st_gpio_irqmux_handler() reads the status register to find out
which banks inside the controller have pending IRQs.
For each banks having pending IRQs, it calls the corresponding handler.
Problem is that current code restricts the number of possible banks inside the
controller to ST_GPIO_PINS_PER_BANK. This define represents the number of pins
inside a bank, so it shouldn't be used here.
On STiH407, PIO_FRONT0 controller has 10 banks, so IRQs pending in the two
last banks (PIO18 & PIO19) aren't handled.
This patch replace ST_GPIO_PINS_PER_BANK by the number of banks inside the
controller.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org> #v3.15+
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have a bunch of Nomadik family pin control drivers, so let's
move them into their own subdirectory.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The XUSB pad controller found on NVIDIA Tegra SoCs provides several pads
that lanes can be assigned to in order to support a variety of interface
options: USB 2.0, USB 3.0, PCIe and SATA.
In addition to the pin controller used to assign lanes to pads two PHYs
are exposed to allow the bricks for PCIe and SATA to be powered up and
down by PCIe and SATA drivers.
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Group all pin control drivers of Samsung platform together in
a sub-directory for easy maintenance.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch moves data allocated using regulator_register to
devm_regulator_register and does away the calls to regulator_unregister.
The sh73a0_pinmux_soc_exit function is no longer needed and is removed.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have four Qualcomm-related pin control drivers, and now there
are drivers coming in for the PMICs on these systems, so let's
create a qcom subdirectory to hold all the Qualcomm stuff.
Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch extends the range of settings configurable via pinfunc API
to cover pin value as well. This allows configuration of default values
of pins, which is useful for pins that are not supposed to be used by
any dedicated driver, but need certain board-specific setting.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
One of remaining limitations of current pinctrl-samsung driver was
the inability to parse multiple pinmux/pinconf group nodes grouped
inside a single device tree node. It made defining groups of pins for
single purpose, but with different parameters very inconvenient.
This patch implements Tegra-like support for grouping multiple pinctrl
groups inside one device tree node, by completely changing the way
pin groups and functions are parsed from device tree. The code creating
pinctrl maps from DT nodes has been borrowed from pinctrl-tegra, while
the initial creation of groups and functions has been completely
rewritten with following assumptions:
- each group consists of just one pin and does not depend on data
from device tree,
- each function is represented by a device tree child node of the
pin controller, which in turn can contain multiple child nodes
for pins that need to have different configuration values.
Device Tree bindings are fully backwards compatible. New functionality
can be used by defining a new pinctrl group consisting of several child
nodes, as on following example:
sd4_bus8: sd4-bus-width8 {
part-1 {
samsung,pins = "gpk0-3", "gpk0-4",
"gpk0-5", "gpk0-6";
samsung,pin-function = <3>;
samsung,pin-pud = <3>;
samsung,pin-drv = <3>;
};
part-2 {
samsung,pins = "gpk1-3", "gpk1-4",
"gpk1-5", "gpk1-6";
samsung,pin-function = <4>;
samsung,pin-pud = <4>;
samsung,pin-drv = <3>;
};
};
Tested on Exynos4210-Trats board and a custom Exynos4212-based one.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Handling of irq_chip operations for GPIO and WKUP external interrupts
is mostly the same, with the difference being offset of registers.
However currently the driver has all the code duplicated for both EINT
types, which is undesirable, because changes in irq_chip operations have
to be done to both instances of the same code.
This patch fixes this by creating exynos_irq_chip struct that has normal
irq_chip struct embedded and contain differences between particular EINT
types, which are three register offsets. One instance of code is removed
and the new structure is used instead to fetch necessary data instead of
samsung_pin_ctrl struct used previously.
While at it, the patch removes Exynos-specific fields from
aforementioned structure to improve layering of the driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds .request() and .free() operations to gpio_chip of
pinctrl-samsung driver, which call pinctrl request and free helpers to
request and free pinctrl pin along with GPIO pin.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch makes the pinctrl-samsung driver configure GPIO direction on
its own, without using the pinctrl_gpio_direction_*() "helpers". The
rationale behind this change is as follows:
- pinctrl-samsung does not need translation from GPIO namespace to
pinctrl namespace to handle GPIO operations - GPIO chip and offset
therein are enough to calculate necessary offsets and bit masks in
constant time,
- the pinctrl_gpio_direction_*() functions do not do anything useful
other than translating the pin into pinctrl namespace and calling the
.gpio_set_direction() from pinmux_ops of the controller,
- the undesirable side effect of using those helpers is losing the
ability to change GPIO direction in atomic context, because they
explicitly use a mutex for synchronization,
Results of this patch are:
- fixed warnings about scheduling while atomic in code that needs to
set GPIO direction in atomic context (e.g. interrupt handler),
- reduced overhead of bitbanging drivers that use gpio_direction_*(),
e.g. i2c-gpio.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For Baytrail, you should never set a GPIO set to direct_irq
to output mode. When direct_irq_en is set for a GPIO, it is
tied directly to an APIC internally, and making the pad output
does not make any sense. Assert a WARN() in the event this happens.
Signed-off-by: Eric Ernst <eric.ernst@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove variable that are never used
This was found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
%d in format string used, but the type is unsigned int
This was found using a static code analysis program called cppcheck
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
%d in format string used, but the type is unsigned int
This was found using a static code analysis program called cppcheck
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove variable that are never used
This was found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove variable that are never used
This was found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove checking if a unsigned is less than zero
This was found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove checking if a unsigned is less than zero
This was found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove checking if a unsigned is less than zero
This was found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove checking if a unsigned is less than zero
This was found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
no .irq_set_wake API is available for pinctrl-st driver.
Add the IRQCHIP_SKIP_SET_WAKE flag to inform irq handler
not to call this API.
Signed-off-by: David Paris <david.paris@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
bcm281xx_pinctrl_probe is local to this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A23 has a R_PIO pin controller, similar to the one found on the A31 SoC.
Add support for the pins controlled by the R_PIO controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A23 uses the same pin controller as previous SoC's from Allwinner.
Add support for the pins controlled by the main PIO controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PINCTRL_SUNXI configuration was kept only to deal with the introduction of
per-machine symbols and the various pintrl drivers through different tree.
Now that it's not useful anymore, we can just remove it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A13 user manual states pins PG0/1/2 only have GPIO input and
interrupt functions. Remove the gpio_out functions for these pins.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
