Per IEEE Std. 802.11-2012, Sec 8.2.4.4.1, the sequence Control field is
not present in control frames. We noticed this problem when processing
Block Ack Requests.
Cc: stable@vger.kernel.org
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Javier Lopez <jlopex@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For a local variable there's no need to use the atomic
set_bit() operation, use __set_bit() instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Prior this fix, those frames were not received, nor forwarded. Fix
this to receive and not forward.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Doing otherwise is wrong, and may wreak havoc on the mpp tables,
specially if the frame is encrypted.
Cc: stable@vger.kernel.org
Reported-by: Chaoxing Lin <Chaoxing.Lin@ultra-3eti.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove a duplicate check in ieee80211_rx_mgmt_beacon,
there is no need to make again the same check for the
IEEE80211_HW_PS_NULLFUNC_STACK twice; the two ifs can
be consolidated.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
[reword commit message & break long lines and also
clean up variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of the current whitelist which accepts duplicates
only for the quiet and vendor IEs, use a blacklist of all
IEs (that we currently parse) that can't be duplicated.
This avoids detecting a beacon as corrupt in the future
when new IEs are added that can be duplicated.
Cc: stable@vger.kernel.org
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Expose a function for the AES-CMAC subkey calculation
to drivers. This is the first step of the AES-CMAC
cipher key setup and may be required for CMAC hardware
offloading.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Before, a mesh STA would execute some code on behalf of AP or IBSS
beacons. Since the mesh stack currently does not consider anything but
other mesh STAs interesting, limit processing to just these and save a
little overhead.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
WDS is (currently) not allowed when channel
contexts are *supported*, not when they're
*not* supported. Fix the inverted test.
Reported-by: Ronald <ronald645@gmail.com>
Tested-by: Ronald <ronald645@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch prepares mac80211 for a later implementation of mesh or
ad-hoc powersave clients.
The structures related to powersave (buffer, TIM map, counters) are
moved from the AP-specific interface structure to a generic structure
that can be embedded into any interface type.
The functions related to powersave are prepared to allow easy
extension with different interface types. For example with:
+ } else if (sta->sdata->vif.type == NL80211_IFTYPE_MESH_POINT) {
+ ps = &sdata->u.mesh.ps;
Some references to the AP's beacon structure are removed where they
were obviously not used.
The patch compiles without warning and has been briefly tested as AP
interface with one client in PS mode.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the user wants to scan using a vif configured as AP,
cfg80211 must give him a chance to do it, even if this
will disrupt the stations performance due to off-channel
scanning. To do so, this patch adds a 'force' flag to the
SCAN_TRIGGER command which tells cfg80211 to perform the
scanning operation even if the vif is an AP and the
beaconing has already started.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The internal function mac80211_format_buffer() has a
printf-style argument list, so add the attribute to
have gcc verify that list.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a number of unused variables that gcc
pointed out (when building with W=1) as well as
some conditions that can never be true due to
the datatypes used: unsigned values can't be
less than zero. Remove this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no vendor-specific mesh sync implemented
and there don't need to be dummy handlers that
only print messages, so remove that code. While
at it, also constify the mesh sync ops.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Initialization of beacon transmission in IBSS mode depends
on whether a new BSS is being created or joined. When joining
an existing IBSS network, beaconing has to start only after
a TSF-sync has happened - this is explained in 11.1.4.
Introduce a new parameter in the BSS information structure to
indicate creator/joiner mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use NL80211_SCAN_FLAG_LOW_PRIORITY flag in mac80211's scan state
machine to prematurely terminate scan operations if outbound
traffic collides. This is useful for marking background scans so
they don't affect throughput.
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
[set feature flag only if software scan is used]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The next patch will introduce a flag that is set
by default in cfg80211 so drivers and mac80211
need to use |= to set features they have so that
they don't clear the already-set feature.
We could set the flag in wiphy_register() instead
of wiphy_new() to avoid this patch, but then the
drivers couldn't *unset* flags they don't want to
use even though the implementation is generic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some changes to fix issues with HT40 APs in Korea
and follow-up changes to allow using HT40 even if
the local regulatory database disallows it caused
issues with iwlwifi (and could cause issues with
other devices); iwlwifi firmware would assert if
you tried to connect to an AP that has an invalid
configuration (e.g. using HT40- on channel 140.)
Fix this, while avoiding the "Korean AP" issue by
disabling HT40 and advertising HT20 to the AP
when connecting.
Cc: stable@vger.kernel.org [3.6]
Reported-by: Florian Reitmeir <florian@reitmeir.org>
Tested-by: Florian Reitmeir <florian@reitmeir.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Save the AP's VHT capabilities (in managed
mode) and make them available to the driver
in the station information.
Unlike HT capabilities, they aren't restricted
to the common capabilities, so drivers must be
aware of their own capabilities.
Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
[fix endian conversion bug ...]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rename struct ieee80211_vht_capabilities to ieee80211_vht_cap
and renamed its member vht_capabilities_info to vht_cap_info.
Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
estab_plinks is not a statistics member. Hence move estab_plinks from
struct mesh_stat to struct ieee80211_if_mesh
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_sta_expire will be called by both IBSS and mesh
interfaces to account for inactive stations, so it would be more
appropriate to use sta_dbg instead of ibss_dbg.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SAE uses two rounds of Authentication frames and both rounds require
considerable calculation to be done. This commit extends the existing
station mode authentication request to allow more control for user
space programs to build the SAE fields and to run the authentication
step ones. Only the second round with authentication transaction
sequence 2 will result in moving to authenticated state.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is useful when debugging authentication process issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Non-zero status code may be needed for Authentication frames, e.g.,
when using SAE.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers may need to iterate the active channel
contexts, export an iterator function to allow
that. To make it possible, use RCU-safe list
functions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On each channel that the device is operating on, it
may need to listen using one or more chains depending
on the SMPS settings of the interfaces using it. The
previous channel context changes completely removed
this ability (before, it was available as the SMPS
mode).
Add per-context tracking of the required static and
dynamic RX chains and notify the driver on changes.
To achieve this, track the chains and SMPS mode used
on each virtual interface and update the channel
context whenever this changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of operating on a single channel only,
use the new channel context infrastructure in
all mac80211 code.
This enables drivers that want to use the new
channel context infrastructure to use multiple
channels, while nothing should change for all
the other drivers that don't support it.
Right now this disables both TX power settings
and spatial multiplexing powersave. Both need
to be re-enabled on a channel context basis.
Additionally, when channel contexts are used
drop the connection when channel switch is
received rather than trying to handle it. This
will have to be improved later.
[With fixes from Eliad and Emmanuel incorporated]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on the driver, channel contexts may be used or
not. If they are used, the driver must have support for
hardware scan and remain-on-channel; otherwise the driver
must not advertise support for multiple channels.
Also prohibit WDS type interfaces when channel contexts
are to be used as there's no clear definition of which
channel they use.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reuse channels with compatible channel types. Some
channel types are compatible and can be used
concurrently.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel context pointer will be accessible on
both assign and unassign events.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce channel context driver methods. The channel
on a context channel is immutable, but the channel type
and other properties can change.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel context are the foundation for multi-channel
operation. They are are immutable and are re-created
(or re-used if other interfaces are bound to a certain
channel and a compatible channel type) on channel
switching.
This is an initial implementation and more features
will come in separate patches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[some changes including RCU protection]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Free tx status skbs when draining power save buffers, pending frames, or
when tearing down a vif.
Fixes remaining conditions that can lead to hostapd/wpa_supplicant hangs when
running out of socket write memory.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fix corruption which can manifest itself by following crash
when switching on rfkill switch with rt2x00 driver:
https://bugzilla.redhat.com/attachment.cgi?id=615362
Pointer key->u.ccmp.tfm of group key get corrupted in:
ieee80211_rx_h_michael_mic_verify():
/* update IV in key information to be able to detect replays */
rx->key->u.tkip.rx[rx->security_idx].iv32 = rx->tkip_iv32;
rx->key->u.tkip.rx[rx->security_idx].iv16 = rx->tkip_iv16;
because rt2x00 always set RX_FLAG_MMIC_STRIPPED, even if key is not TKIP.
We already check type of the key in different path in
ieee80211_rx_h_michael_mic_verify() function, so adding additional
check here is reasonable.
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avoid situation when we are on associate state in mac80211 and
on disassociate state in cfg80211. This can results on crash
during modules unload (like showed on this thread:
http://marc.info/?t=134373976300001&r=1&w=2) and possibly other
problems.
Reported-by: Pedro Francisco <pedrogfrancisco@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few places free skbs using dev_kfree_skb even though they're called
after ieee80211_subif_start_xmit might have cloned it for tracking tx
status. Use ieee80211_free_txskb here to prevent skb leaks.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The call to drv_get/set_tsf() was put on the workqueue to perform tsf
adjustments since that function might sleep. However it ended up inside
a spinlock, whose critical section must be atomic. Do tsf adjustment
outside the spinlock instead, and get rid of a warning.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bits used in the mask were off-by-one and ended up masking PwrMgt,
MoreData, Protected fields instead of Retry, PwrMgt, MoreData. Fix this
and to mask the correct fields. While doing so, convert the code to mask
the full FC using IEEE80211_FCTL_* defines similarly to how CCMP AAD is
built.
Since BIP is used only with broadcast/multicast management frames, the
Retry field is always 0 in these frames. The Protected field is also
zero to maintain backwards compatibility. As such, the incorrect mask
here does not really cause any problems for valid frames. In theory, an
invalid BIP frame with Retry or Protected field set to 1 could be
rejected because of BIP validation. However, no such frame should show
up with standard compliant implementations, so this does not cause
problems in normal BIP use.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a station is removed and we stop the aggregation
sessions, it's not useful to send delBA since this is
due to us or the station disassociating or dropping
the connection in some other way, so change that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we disassociate, it's not really useful to
send delBA action frames since we're going to send
disassoc/deauth anyway, so change that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the IBSS auth TX debug message the BSSID and DA
address are reversed, fix that.
Signed-off-by: Sylvain Roger Rieunier <sylvain.roger.rieunier@gmail.com>
[reword commit message and make it fit 72 cols]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The suspend/resume code depends on CONFIG_PM, so
the reset debugfs file can only be made available
if that is enabled.
Fengguang Wu's zero-day build testing found this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Peer link which is blocked using the "iw mesh0 station
set <MAC addr> plink_action block" is previously not able
to re-open using "iw mesh0 station set <MAC addr>
plink_action open". This patch is intended to solve this.
If the station plink state remains at OPN_SNT once open,
try block and open again should solve this problem.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, mac80211 uses the power constraint IE, and reduces
the regulatory max TX power by it. This can cause issues if
the AP is advertising a large power constraint value matching
a high TX power in its country IE, for example in this case:
...
Country: US Environment: Indoor/Outdoor
...
Channels [157 - 157] @ 30 dBm
...
Power constraint: 13 dB
...
What happened here is that our local regulatory TX power is
15 dBm, and gets reduced by 13 dB so we end up with only
2 dBm effective TX power, which is way too low.
Instead, handle the country IE/power constraint IE combined
and restrict our TX power to the max of the regulatory power
and the maximum power advertised by the AP, in this case
17 dBm (= 30 dBm - 13 dB).
Also print a message when this happens to let the user know
and help us debug issues with it.
Reported-by: Carl A. Cook <CACook@quantum-equities.com>
Tested-by: Carl A. Cook <CACook@quantum-equities.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The functions are only called if CONFIG_PM is set
as the callers are under an ifdef, so there's no
need to also define no-op functions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
skb->dev might contain a stale reference to a device that was already
deleted, and using it unchecked can lead to invalid pointer accesses.
Since this is only used for nl80211 tx, iterate over active interfaces
to find a match for skb->dev, and discard the tx status if the device
is gone.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 calls synchronize_rcu() on sta deletion,
which increase the roaming time significantly.
Convert it into a call_rcu() mechanism, in order
to avoid blocking. Since some of the cleanup
functions might sleep, schedule from the call_rcu
callback a new work that will do the actual cleanup.
In order to make sure the cleanup occurs before
the interface went down, flush local->workqueue
on ieee80211_do_stop().
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mark keys that might be used to receive management
frames so drivers can fall back on software crypto
for them if they don't support hardware offload.
As the new flag is only set correctly for RX keys
and the existing IEEE80211_KEY_FLAG_SW_MGMT flag
can only affect TX, also rename the latter to
IEEE80211_KEY_FLAG_SW_MGMT_TX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Whenever a host gets an AUTH frame it first allocates a new
station and then replies with another AUTH frame. However,
if sta allocations fails the host should send a DEAUTH frame
instead to tell the other end that something went wrong.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
[reword commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move ieee80211_send_deauth_disassoc() to util.c to make it
available for the rest of the mac80211 code.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
removes unnecessary semicolon
Found by Coccinelle: http://coccinelle.lip6.fr/
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split functionality for further reuse.
Will prevent code duplication when channel context
channel_type merging is introduced.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
__ieee80211_key_destroy() calls synchronize_rcu() in
order to sync the tx path before destroying the key.
However, synching the tx path can be done with
synchronize_net() as well, which is usually faster
(the timing might be important for roaming scenarios).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The power constraint IE is always a single byte
so check the size when parsing instead of later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Disconnect from the AP if channel switching in the
driver failed or if the new channel is unavailable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to keep a copy of the scheduled
scan IEs after the driver has been told, if it
requires a copy it must make one. Therefore, we
can move sched_scan_ies into the function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull in mac80211.git to let the next patch apply
without conflicts, also resolving a hwsim conflict.
Conflicts:
drivers/net/wireless/mac80211_hwsim.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using list_move() instead of list_del() + list_add().
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Various small fixes for net/mac80211/cfg.c:mpath_set_pinfo():
Initialize *pinfo before filling members in, handle MESH_PATH_RESOLVED
correctly, and remove bogus assignment; result in correct display
of FLAGS values and meaningful EXPTIME for expired paths in iw utility.
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Doing so creates warnings, but the function is internal and
not part of the 802.11 docbooks, so it from kerneldoc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ifmgd->bssid wasn't cleared properly in some
auth/assoc failure cases, causing mac80211 and
the low-level driver to go out of sync.
Clear ifmgd->bssid on failure, and notify the driver.
Cc: stable@kernel.org # 3.4+
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A P2P Device interface does not have a netdev, and is not
expected to be used for transmitting data, so there is no
need to assign hw queues for it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit mac80211: avoid using synchronize_rcu in ieee80211_set_probe_resp
changed the return value when the probe response template is not present.
Revert to the earlier value of 1 - this fixes AP mode for drivers like
ath9k.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The destination address of unicast frames forwarded through a mesh gate
was being replaced with the broadcast address. Instead leave the
original destination address as the mesh DA. If the nexthop address is
not in the mpath table it will be resolved. If that fails, the frame
will be forwarded to known mesh gates.
Reported-by: Cedric Voncken <cedric.voncken@acksys.fr>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In multi-channel scenarios, the channel that we will
transmit a probe request on isn't always the current
channel (which will be NULL anyway) but will instead
be the channel that the AP is on. Pass the channel
to the ieee80211_send_probe_req() function so it can
be used in the different scenarios. The scan code
continues to pass the current channel, of course.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The optimisation of scanning only on the current
channel should check the operating channel. Also
modify it to compare channel pointer rather than
the frequency.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even for single-channel devices it is possible that we
switch the channel temporarily (e.g. for scanning) but
while doing so process a received frame that was still
received on the old channel, so checking the current
band is racy. Use the band from status instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the move to multi-channel and away from
drv_config(), hw.conf.channel will not always
be set, only for devices using the current API
instead of the new channel context APIs. Check
the channel is set before adding its frequency
to the trace data.
Also break some overly long lines in the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using hw.conf.channel is wrong as it could be the
temporary channel if the station is added from the
workqueue while the device is already on another
channel. Use oper_channel instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using local->_oper_channel_type in the mesh code is
completely wrong as this value is the combination
of the various interface channel types and can be
a different value from the mesh interface in case
there are multiple virtual interfaces.
Use sdata->vif.bss_conf.channel_type instead as it
tracks the per-vif channel type.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to use a single scratch buffer and
calculate offsets into it, just use two separate
buffers for the separate variables.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices like the current iwlwifi implementation
require that the P2P interface address match the P2P
Device address (only one P2P interface is supported.)
Add the HW flag IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF
that allows drivers to request that P2P Interfaces
added while a P2P Device is active get the same MAC
address by default.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After cfg80211 got a P2P Device abstraction, add
support to mac80211. Whether it really is supported
or not will depend on whether or not the driver has
support for it, but mac80211 needs to change to be
able to support drivers that need a P2P Device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support using a different MAC address
for the P2P Device address we must first have a
P2P Device abstraction that can be assigned a MAC
address.
This abstraction will also be useful to support
offloading P2P operations to the device, e.g.
periodic listen for discoverability.
Currently, the driver is responsible for assigning
a MAC address to the P2P Device, but this could be
changed by allowing a MAC address to be given to
the NEW_INTERFACE command.
As it has no associated netdev, a P2P Device can
only be identified by its wdev identifier but the
previous patches allowed using the wdev identifier
in various APIs, e.g. remain-on-channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to declare the function in the
header file since it's only used in a single
place, so make it static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel switch IE has a fixed size, so we can
discard it in parsing if it's not the right size
and use the right struct pointer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The time until the channel switch is in TU,
not in milliseconds, so use TU_TO_EXP_TIME()
to correctly program the timer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clean up the CSA handling code by moving some
of it out of the if and using a C99 initializer
for the struct passed to the driver method.
While at it, also add a comment that we should
wait for a beacon after switching the channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support getting A-MPDU status information from the
drivers and reporting it to userspace via radiotap
in the standard fields.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In IBSS it is possible that the supported rates set for a station changes over
time (e.g. it gets first initialised as an empty set because of no available
information about rates and updated later). In this case the driver has to be
notified about the change in order to update its internal table accordingly (if
needed).
This behaviour is needed by all those drivers that handle rc internally but
leave stations management to mac80211
Reported-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
[Johannes - add docs, validate IBSS mode only, fix compilation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use skb_queue_walk_safe instead, and fix a few issues:
- didn't free old skbs on moving
- didn't react to failed skb alloc
- needlessly held a local pointer to the destination frame queue
- didn't check destination queue length before adding skb
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since all we really want is just to iterate over all skbs, do just that
and avoid (de)queueing to a clusmy tmpq.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This could take a while (100ms+) and may delay sending assoc resp
in AP mode with WPS or P2P GO (as setting the probe resp takes place
there). We've encountered situations where the delay was big enough
to cause connection problems with devices like Galaxy Nexus.
Switch to using call_rcu with a free handler.
[Arik - rework to use plain buffer and instead of skb]
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_bss_info_change_notify is called everytime a peer link is established
or closed, because the accepting_plinks flag in the meshconf IE *might* have changed.
With this patch the corresponding functions return the BSS_CHANGED_BEACON flag when a beacon update is necessary.
Also it makes mesh_accept_plinks_update the common place to update the accepting_plinks flag.
mesh_accept_plinks_update is called upon plink change and also periodically from ieee80211_mesh_housekeeping.
Thus, it also picks up changes of local->num_sta.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Acked-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although adding an IE is almost guaranteed to succeed since we already
accounted for its length while allocating the skb, we should still free
the skb in case of failure.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It doesn't make a lot of sense to wait for an ack in response to a
peering close frame since either peer in this exchange could be going
down.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function was only used by mesh, and not really needed since any
interface-specific cleanup already happens in the netdev handlers.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is not necessary to stop the mesh beacon in the mac80211 ndo_stop
handler, since cfg80211 has already left the mesh on NETDEV_GOING_DOWN
notification.
Also some improvements to ieee80211_stop_mesh():
- flush mpath entries.
- flush sta entries per-sdata so we don't remove entries belonging to
other vifs on the same hw.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh path timer needs to be canceled when
leaving the mesh as otherwise it could fire
after the interface has been removed already.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a corner case that can happen when we
suspend with a timer running, then resume and
disconnect. If we connect again, suspend and
resume we might start timers that shouldn't be
running. Reset the timer flags to avoid this.
This affects both mesh and managed modes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When associating anew, the old station MLME flags should
be cleared. The only exception is the 40 MHz disable
flag as it might have been set while the channel was set
in a previous authentication attempt so it needs to be
kept intact.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enable the carrier on WDS type interfaces only
after having added the station entry for the
WDS peer so outgoing frames will find it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of assuming the carrier is on all
the time in mesh manage it with joining
and leaving the mesh.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we only need the band, remove the channel
pointer from struct ieee80211_tx_data and also
assign it properly, depending on context, to the
correct operating or current channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When sending probe requests, e.g. during software scanning,
these will go out on the *current* channel, so their IEs
need to be built from the current channel. At other times,
e.g. for beacons or probe request templates, the IEs will
be used on the *operating* channel and using the current
channel instead might result in errors.
Add the appropriate parameters to respect the difference.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using hw.conf.channel is wrong as it could be the
temporary channel if any function like the beacon
get function is called while scanning or during
other temporary out-of-channel activities.
Use oper_channel instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using hw.conf.channel is wrong as it could be the
temporary channel if any function like the beacon
get function is called while scanning or during
other temporary out-of-channel activities.
Use oper_channel instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using hw.conf.channel is wrong as it could be the
temporary channel if any function like the beacon
get function is called while scanning or during
other temporary out-of-channel activities.
Use oper_channel instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using hw.conf.channel is wrong as it could be the
temporary channel if any function like the beacon
get function is called while scanning or during
other temporary out-of-channel activities.
Use oper_channel instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to set up the channel during auth
and again during assoc, just do it once. Currently
this doesn't result in any changes since calling
hw_config() with an unchanged channel will return
early, but with the channel context work this has
an impact on channel context assignment.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_prep_connection(), the station (if not NULL)
is the new station (representing the AP) that needs to be
added. Rename the variable to "new_sta" to clarify this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If HT/VHT isn't supported by us we shouldn't print
a message that we disabled it, do that only if the
AP didn't support WMM and we therefore disable it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the control.sta pointer from ieee80211_tx_info to free up
sufficient space in the TX skb control buffer for the upcoming
Transmit Power Control (TPC).
Instead, the pointer is now on the stack in a new control struct
that is passed as a function parameter to the drivers' tx method.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[reworded commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, ps mode is indicated per device (rather than
per interface), which doesn't make a lot of sense.
Moreover, there are subtle bugs caused by the inability
to indicate ps change along with other changes
(e.g. when the AP deauth us, we'd like to indicate
CHANGED_PS | CHANGED_ASSOC, as changing PS before
notifying about disassociation will result in null-packets
being sent (if IEEE80211_HW_SUPPORTS_DYNAMIC_PS) while
the sta is already disconnected.)
Keep the current per-device notifications, and add
parallel per-vif notifications.
In order to keep it simple, the per-device ps and
the per-vif ps are orthogonal - the per-vif ps
configuration is determined only by the user
configuration (enable/disable) and the connection
state, and is not affected by other vifs state and
(temporary) dynamic_ps/offchannel operations
(unlike per-device ps).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This doesn't make any sense since we are expected to be on
the medium or at least to Tx only when we are on the right
channel and the AP/GO can hear us.
Move the call to mgd_prepare_tx() for deauth to be only
done in case we're sending a deauth while not associated.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the HW is monitoring connection loss (as advertised
by IEEE80211_HW_CONNECTION_MONITOR) but not filtering
beacons (IEEE80211_VIF_BEACON_FILTER) then mac80211 will
still start the beacon loss timer and if a few beacons
are lost, e.g. due to scanning, drop the connection.
If the hardware doesn't advertise connection monitoring,
then it won't drop the connection right away but probe
the AP, which is intended, but due to the logic in the
timer when connection monitoring is done it assumes the
connection was actually lost.
Fix this problem by not starting the timer when the HW
does connection monitoring.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Insert VHT IEs into association frames to allow
mac80211 to connect as a VHT client.
Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
[clarify commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rate control is re-initialized whenever a beacon from a mesh
peer received, breaking the algorithms and resulting in low
performance. Return early from mesh_peer_init if we already
established a link with this peer to avoid this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[clarify commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_request_sched_scan_stop() cleared
local->sched_scan_sdata. However, sched_scan_sdata
should be cleared only after the driver calls
ieee80211_sched_scan_stopped() (like with normal hw scan).
Clearing sched_scan_sdata too early caused
ieee80211_sched_scan_stopped_work to exit prematurely
without properly cleaning all the sched scan resources
and without calling cfg80211_sched_scan_stopped (so
userspace wasn't notified about sched scan completion).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull LED subsystem update from Bryan Wu.
* 'for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (50 commits)
leds-lp8788: forgotten unlock at lp8788_led_work
LEDS: propagate error codes in blinkm_detect()
LEDS: memory leak in blinkm_led_common_set()
leds: add new lp8788 led driver
LEDS: add BlinkM RGB LED driver, documentation and update MAINTAINERS
leds: max8997: Simplify max8997_led_set_mode implementation
leds/leds-s3c24xx: use devm_gpio_request
leds: convert Network Space v2 LED driver to devm_kzalloc() and cleanup error exit path
leds: convert DAC124S085 LED driver to devm_kzalloc()
leds: convert LM3530 LED driver to devm_kzalloc() and cleanup error exit path
leds: convert TCA6507 LED driver to devm_kzalloc()
leds: convert Freescale MC13783 LED driver to devm_kzalloc() and cleanup error exit path
leds: convert ADP5520 LED driver to devm_kzalloc() and cleanup error exit path
leds: convert PCA955x LED driver to devm_kzalloc() and cleanup error exit path
leds: convert Sun Fire LED driver to devm_kzalloc() and cleanup error exit path
leds: convert PCA9532 LED driver to devm_kzalloc()
leds: convert LT3593 LED driver to devm_kzalloc()
leds: convert Renesas TPU LED driver to devm_kzalloc() and cleanup error exit path
leds: convert LP5523 LED driver to devm_kzalloc() and cleanup error exit path
leds: convert PCA9633 LED driver to devm_kzalloc()
...
Rename leds external interface led_brightness_set() to led_set_brightness().
This is the second phase of the change to reduce confusion between the
leds internal and external interfaces that set brightness. With this change,
now the external interface is led_set_brightness(). The first phase renamed
the internal interface led_set_brightness() to __led_set_brightness().
There are no changes to the interface implementations.
Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
When AP interface is going down, the stations
are flushed (in ieee80211_do_stop()) only after
the beaconing was stopped.
However, drivers might rely on stations being
removed before the beaconing was stopped, in
order to clean up properly.
Fix it by flushing the stations on ap stop.
(we already do the same for other interface
types, e.g. in ieee80211_set_disassoc())
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
on disassoc, ieee80211_set_disassoc() goes out of PS
before indicating BSS_CHANGED_ASSOC (not sure why this
is needed, but some drivers might count on the current
behavior).
However, it does it after sending the disassoc
frame, which results in null-data frame being sent
(in order to go out of ps) after we were already sent
the disassoc, which is invalid.
Fix it by going out of ps before sending the disassoc.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
commit "mac80211: unify SW/offload remain-on-channel"
moved the cookie assignment from ieee80211_mgmt_tx()
to ieee80211_start_roc_work(). But the latter is only
called where offchannel is needed. If offchannel isn't
needed/used, a uninitialized cookie value would be returned
to userspace.
This patch sets the cookie value when offchannel isn't used.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This essentially reverts commit 2e165b8184 but
introduces the get_channel operation with a new
wireless_dev argument so that you can retrieve
the channel per interface. This is necessary as
even though we can track all interface channels
(except monitor) we can't track the channel type
used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 870d37fc22.
This code doesn't work as cfg80211 will call
set_monitor_enabled at the wrong time and it
doesn't seem to be possible to fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
roc is destroyed then roc->started is referenced. Keep a local cache.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the virtual monitor interface is requested
by the driver, it should also be iterated over
when the driver wants to iterate all active
interfaces.
To allow that protect it with the iflist_mtx.
Change-Id: I58ac5de2f4ce93d12c5a98ecd2859f60158d5d69
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When sample_idx is set to a value other than -1 it activates
the IEEE80211_TX_CTL_RATE_CTRL_PROBE flag which disables
frame aggregation. To allow frame aggregation during fixed
rate it is necessary to set max_tp_rate, max_tp_rate2 and
max_prob_rate instead of sample_idx.
Signed-off-by: Sylvain Roger Rieunier <sylvain.roger.rieunier@gmail.com>
[reword commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When drop_unencrypted is enabled and MFP is disabled,
non-robust management frames for not-yet associated STA are dropped.
This isn't visible as many management frames sent from the kernel
have TX_INTFL_DONT_ENCRYPT set and management frames injected
from a monitor vif have TX_CTL_INJECTED so aren't dropped.
But management frames sent from userspace via NL80211_CMD_FRAME
do not have this flag set, so are dropped.
This patch make it always accept non-robust management frames.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "no key" case in key selection that decides
whether to drop the frame or not is impossible
to understand, restructure the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[cavallar@lri.fr: removed blank line and restructured action frame clause]
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Johannes Berg
Javier Cardona
Rami Rosen
Assaf Krauss
Thomas Pedersen
John W. Linville
Marco Porsch
Antonio Quartulli
Sujith Manoharan
Sam Leffler
Mahesh Palivela
Ashok Nagarajan
Mohammed Shafi Shajakhan
Jouni Malinen
Michal Kazior
Felix Fietkau
Stanislaw Gruszka
Sylvain Roger Rieunier
Chun-Yeow Yeoh
Eliad Peller
Peter Senna Tschudin
Wei Yongjun
LEO Airwarosu Yoichi Shinoda
Ilan Peer
Sujith Manoharan
Eyal Shapira
Thomas Huehn
Emmanuel Grumbach
Linus Torvalds
Shuah Khan
Nicolas Cavallari
Alan Cox