smatch warns that the RC query code could go past the array size:
drivers/media/usb/dvb-usb-v2/rtl28xxu.c:1757 rtl2832u_rc_query() error: buffer overflow 'buf' 128 <= 130
drivers/media/usb/dvb-usb-v2/rtl28xxu.c:1758 rtl2832u_rc_query() error: buffer overflow 'buf' 128 <= 130
The driver logic gets the length of the IR RX buffer with:
ret = rtl28xxu_rd_reg(d, IR_RX_BC, &buf[0]);
...
len = buf[0];
In thesis, this could range between 0 and 255 [1].
While this should never happen in practice, due to hardware limits,
smatch is right when it complains about that, as there's nothing at
the logic that would prevent it. So, if for whatever reason, buf[0]
gets filled by rtl28xx read functions with a value bigger than 128,
it will go past the array.
So, add an explicit check.
[1] I've no idea why smatch thinks that the maximum value is 130.
I double-checked the code several times. Was unable to find any
reason for assuming 130. Perhaps smatch is not properly parsing
u8 here?
Fixes: b5cbaa43a6 ("[media] rtl28xx: initial support for rtl2832u")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Trivial fix to spelling mistake in au0828_isocdbg debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Trivial fix to spelling mistake in dev_dbg debug messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Trivial fix to spelling mistake in dev_dbg and dev_err messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Trivial fix to spelling mistake in debug and error messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
hackrf_submit_urbs(), hackrf_alloc_stream_bufs() and hackrf_alloc_urbs()
are never called in atomic context.
They call usb_submit_urb(), usb_alloc_coherent() and usb_alloc_urb()
with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
em28xx_pre_card_setup() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
em28xx_init_usb_xfer() is never called in atomic context.
It calls usb_submit_urb() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Each call to dw2102_probe() allocates memory by kmemdup for structures
p1100, s660, p7500 and s421, but there is no their deallocation.
dvb_usb_device_init() copies the corresponding structure into
dvb_usb_device->props, so there is no use of original structure after
dvb_usb_device_init().
The patch moves structures from global scope to local and adds their
deallocation.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Right now, satellite frontend drivers specify frequencies in kHz,
while terrestrial/cable ones specify in Hz. That's confusing
for developers.
However, the main problem is that universal frontends capable
of handling both satellite and non-satelite delivery systems
are appearing. We end by needing to hack the drivers in
order to support such hybrid frontends.
So, convert everything to specify frontend frequencies in Hz.
Tested-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Right now, satellite tuner drivers specify frequencies in kHz,
while terrestrial/cable ones specify in Hz. That's confusing
for developers.
However, the main problem is that universal tuners capable
of handling both satellite and non-satelite delivery systems
are appearing. We end by needing to hack the drivers in
order to support such hybrid tuners.
So, convert everything to specify tuner frequencies in Hz.
Plese notice that a similar patch is also needed for frontends.
Tested-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch disables the null packet filter for the Hauppauge
WinTV-dualHD. There are applications which require the unfiltered
transport stream (e.g. DOCSIS segment load analyzers).
Tests showed that the device is capable of delivering two unfiltered
EuroDOCSIS 3.0 transport streams simultaneously, i.e. over 100 Mbit/s
worth of data, without any losses.
Signed-off-by: Robert Schlabbach <Robert.Schlabbach@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The em28xx driver never touched the EM2874 register bits that control
the transport stream packet filters, leaving them at whatever default
the firmware has set. E.g. the Pinnacle 290e disables them by default,
while the Hauppauge WinTV dualHD enables discarding NULL packets by
default.
However, some applications require NULL packets, e.g. to determine the
load in DOCSIS segments, so discarding NULL packets is undesired for
such applications.
This patch simply extends the bit mask when starting or stopping the
transport stream packet capture, so that the filter bits are cleared.
It has been verified that this makes the Hauppauge WinTV dualHD pass
an unfiltered DVB-C stream including NULL packets, which it didn't
before.
Signed-off-by: Robert Schlabbach <Robert.Schlabbach@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Friio device contains "gl861" bridge and "tc90522" demod,
for which the separate drivers are already in the kernel.
But friio driver was monolithic and did not use them,
practically copying those features.
This patch decomposes friio driver into sub drivers and
re-uses existing ones, thus reduces some code.
It adds some features to gl861,
to support the friio-specific init/config of the devices
and implement i2c communications to the tuner via demod
with USB vendor requests.
[mchehab+samsung@kernel.org: fix merge conflicts]
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
UVC defines a method of handling asynchronous controls, which sends a
USB packet over the interrupt pipe. This patch implements support for
such packets by sending a control event to the user. Since this can
involve USB traffic and, therefore, scheduling, this has to be done
in a work queue.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When a command ends up in a STALL on the control pipe, use the Request
Error Code control to provide a more precise error information to the
user. For example, if a camera is still busy processing a control,
when the same or an interrelated control set request arrives, the
camera can react with a STALL and then return the "Not ready" status
in response to a UVC_VC_REQUEST_ERROR_CODE_CONTROL command. With this
patch the user would then get an EBUSY error code instead of a
generic EPIPE.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Event subscribers cannot have a NULL file handle. They are only added
at a single location in the code, and the .fh pointer is used without
checking there.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Just like for ISOC, validate the decoded BULK buffer size when possible.
This avoids sending corrupted or partial buffers to userspace, which may
lead to application crash or run-time failure.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
[laurent.pinchart@ideasonboard.com: Move uvc_video_validate_buffer() call to uvc_video_next_buffers()]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the 8-bit IR format GUID defined in the Microsoft Kernel
Streaming Media API.
Reported-by: Paul Menzel <pmenzel+linux-media@molgen.mpg.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Paul Menzel <pmenzel+linux-media@molgen.mpg.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Right now, the code that calculates alternate modes is not ready
for devices with dual tuners. That's ok, as we currently don't
have any such devices, but better to add a warning for such
case, as, if anyone adds such device, the logic will need to
be reviewed.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Half-revert: commit 5b1a270d22 ("media: dvb: add alternative USB PID for Hauppauge WinTV-soloHD")'
The PID already exists on the line above.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Michael Ira Krufky <mkrufky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Addresses the following, which introduced a regression itself:
Commit 509f89652f ("media: em28xx: fix a regression with HVR-950")
The regression fix breaks dual transport stream support. Currently,
when a tuner starts streaming it sets alt mode on the USB interface.
The problem is, in a dual tuner model, both tuners share the same
USB interface, so when the second tuner becomes active and sets alt
mode on the interface it kills streaming on the other port.
This patch addresses the regression by only setting alt mode
on the USB interface during em28xx_start_streaming, if the
device is not a dual tuner model. This allows all older and
single tuner devices to explicitly set alt mode during stream
startup. Testers report both isoc and bulk DualHD models work
correctly with the alt mode set only once, in em28xx_dvb_init.
Fixes: 509f89652f ("media: em28xx: fix a regression with HVR-950")
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Michael Ira Krufky <mkrufky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add FIXME code comment:
/* FIXME: check if it is fe_adap[1] */
It is likely that it should be adap->fe_adap[1].fe in the second clause,
but this has never been verified.
Suggested-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit 1eace8344c ("i2c: add param sanity check to
i2c_transfer()"), the I2C core does this check now. We can remove it
from drivers.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit 1eace8344c ("i2c: add param sanity check to
i2c_transfer()"), the I2C core does this check now. We can remove it
from drivers.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit 1eace8344c ("i2c: add param sanity check to
i2c_transfer()"), the I2C core does this check now. We can remove it
from drivers.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit 1eace8344c ("i2c: add param sanity check to
i2c_transfer()"), the I2C core does this check now. We can remove it
from drivers.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit 1eace8344c ("i2c: add param sanity check to
i2c_transfer()"), the I2C core does this check now. We can remove it
from drivers.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Probe of dvb_usb_gl861 was working at least with v4.4. Noticed the issue
with v4.13 but according to similar issues the problem started with v4.9.
[ 15.288065] transfer buffer not dma capable
[ 15.288090] WARNING: CPU: 2 PID: 493 at drivers/usb/core/hcd.c:1595 usb_hcd_map_urb_for_dma+0x4e2/0x640
...CUT...
[ 15.288791] dvb_usb_gl861: probe of 3-7:1.0 failed with error -5
Tested with MSI Mega Sky 580 DVB-T Tuner [GL861]
[mchehab+samsung@kernel.org: rebased on the top of upstream]
Cc: stable@vger.kernel.org
Signed-off-by: Mika Båtsman <mika.batsman@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Comparing an int to a size, which is unsigned, causes the int to become
unsigned, giving the wrong result. kinect_read returns the result of
usb_control_msg, which can return a negtive error code.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
int x;
expression e,e1;
identifier f;
@@
*x = f(...);
... when != x = e1
when != if (x < 0 || ...) { ... return ...; }
*x < sizeof(e)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The vb2_queue will soon be mandatory. The videobuf2 core
will throw a verbose warning if it's not set.
The stk1160 driver is setting the queue lock, but after
the vb2_queue_init call. Avoid the warning by setting
the lock before the queue initialization.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When dvb_register_adapter fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling dvb_register_adapter.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
[hans.verkuil@cisco.com: use pr_err and fix typo: adater -> adapter]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
With CONFIG_RC_CORE=m and VIDEO_CX231XX=y, we get a link failure:
drivers/media/usb/cx231xx/cx231xx-input.o: In function `cx231xx_ir_init':
cx231xx-input.c:(.text+0xd4): undefined reference to `rc_allocate_device'
This narrows down the dependency so that only valid configurations
are allowed.
Fixes: 84545d2a14 ("media: cx231xx: Remove RC_CORE dependency")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are several places pointing to old documentation files:
Documentation/video4linux/API.html
Documentation/video4linux/bttv/
Documentation/video4linux/cx2341x/fw-encoder-api.txt
Documentation/video4linux/m5602.txt
Documentation/video4linux/v4l2-framework.txt
Documentation/video4linux/videobuf
Documentation/video4linux/Zoran
Make them point to the new location where available, removing
otherwise.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
This file got renamed, but the references still point to the
old place.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
This script was moved out of Documentation/dvb, but the
links weren't updated.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
As we move stuff around, some doc references are broken. Fix some of
them via this script:
./scripts/documentation-file-ref-check --fix
Manually checked if the produced result is valid, removing a few
false-positives.
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
The addition of an extra operation to use the GET_INFO command
overwrites all existing flags from the uvc_ctrls table. This includes
setting all controls as supporting GET_MIN, GET_MAX, GET_RES, and
GET_DEF regardless of whether they do or not.
Move the initialisation of these control capabilities directly to the
uvc_ctrl_fill_xu_info() call where they were originally located in that
use case, and ensure that the new functionality in uvc_ctrl_get_flags()
will only set flags based on their reported capability from the GET_INFO
call.
Fixes: 859086ae36 ("media: uvcvideo: Apply flags from device to actual properties")
Cc: stable@vger.kernel.org
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Tested-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
media: uvcvideo: Support UVC 1.5 video probe & commit controls
The length of UVC 1.5 video control is 48, and it is 34 for UVC 1.1.
Change it to 48 for UVC 1.5 device, and the UVC 1.5 device can be
recognized.
More changes to the driver are needed for full UVC 1.5 compatibility.
However, at least the UVC 1.5 Realtek RTS5847/RTS5852 cameras have been
reported to work well.
[laurent.pinchart@ideasonboard.com: Factor out code to helper function, update size checks]
Cc: stable@vger.kernel.org
Signed-off-by: ming_qian <ming_qian@realsil.com.cn>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Ana Guerrero Lopez <ana.guerrero@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
kref_init initializes the reference count to 1, not 0. This additional
reference is never released since the conversion to reference counters.
As a result, uvc_delete is not called anymore when UVC cameras are
disconnected.
Fix this by adding an additional kref_put in uvc_disconnect and in the
probe error path. This also allows to remove the temporary additional
reference in uvc_unregister_video.
Fixes: 9d15cd958c ("media: uvcvideo: Convert from using an atomic variable to a reference count")
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The 50Hz and 60Hz power line frequency settings disable short (1/120s
and 1/100s) exposure times for banding filter (causing overexposed
image near lamps). No flicker setting enables them (when banding
filter is disabled and they're not used).
Seems that the logic is just the wrong way around.
(This bug came from the Windows driver.)
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Power line frequency settings for OV7648 sensor contain autogain
and exposure commands, affecting unrelated controls. Remove them.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ZS0211 internal autogain causes pumping and flickering with OV7648
sensor on 0ac8:307b webcam.
Implement OV7648 autogain and exposure control and use that instead.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
