Add support for inner header RSS on IP-in-IP and IPv6 tunneled packets.
Add rules to the steering table regarding outer IP header, with
IPv4/6->IP-in-IP. Tunneled packets with protocol numbers: 0x4 (IP-in-IP)
and 0x29 (IPv6) are RSS-ed on the inner IP header.
Separate FW dependencies between flow table inner IP capabilities and
GRE offload support. Allowing this feature even if GRE offload is not
supported. Tested with multi stream TCP traffic tunneled with IPnIP.
Verified that:
Without this patch, only a single RX ring was processing the traffic.
With this patch, multiple RX rings were processing the traffic.
Verified with and without GRE offload support.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Move function which indicates whether tunnel inner flow table is
supported from en.h to en_fs.c. It fits better right after tunnel
protocol rules definitions.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added the following packets drop counter:
Device out of buffer - counts packets which were dropped due to full
device internal receive queue.
This counter will be shown on ethtool as a new counter called
dev_out_of_buffer.
The counter is read from FW by command QUERY_VNIC_ENV.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When the VF LAG is in use, round-robin the TX affinity of channels among
the different ports, if supported by the firmware. Create a set of TISes
per port, while doing round-robin of the channels over the different
sets. Let all SQs of a channel share the same set of TISes.
If lag_tx_port_affinity HCA cap bit is supported, num_lag_ports > 1 and
we aren't the LACP owner (PF in the regular use), assign the affinities,
otherwise use tx_affinity == 0 in TIS context to let the FW assign the
affinities itself. The TISes of the LACP owner are mapped only to the
native physical port.
For VFs, the starting port for round-robin is determined by its vhca_id,
because a VF may have only one channel if attached to a single-core VM.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For better modularity and code sharing.
Function internal change to be introduced in the next patches.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix a typo in 'mlx5e_refomrat_wol_mode_mlx5_to_linux' and
'mlx5e_refomrat_wol_mode_linux_to_mlx5' function names:
"refomrat" -> "reformat".
Fixes: 928cfe8745 ("net/mlx5e: Wake On LAN support")
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5 HW spec and bits updates:
1) Aya exposes IP-in-IP capability in mlx5_core.
2) Maxim exposes lag tx port affinity capabilities.
3) Moshe adds VNIC_ENV internal rq counter bits.
4) ODP capabilities for DC transport
Misc updates:
5) Saeed, two compiler warnings cleanups
6) Add XRQ legacy commands opcodes
7) Use refcount_t for refcount
8) fix a -Wstringop-truncation warning
In mlx5_core initialization, query max ODP capabilities for DC transport
from FW and set as current capabilities.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Voon Weifeng says:
====================
stmmac: Add EHL and TGL PCI info and PCI ID
In order to keep PCI info simple and neat, this patch series have
introduced a 3 hierarchy of struct. First layer will be the
intel_mgbe_common_data struct which keeps all Intel common configuration.
Second layer will be xxx_common_data which keeps all the different Intel
microarchitecture, e.g tgl, ehl. The third layer will be configuration
that tied to the PCI ID only based on speed and RGMII/SGMII interface.
EHL and TGL will also having a higher system clock which is 200Mhz.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
EHL DW EQOS is running on a 200MHz clock. Setting up stmmac-clk,
ptp clock and ptp_max_adj to 200MHz.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added EHL RGMII 1Gbps PCI ID. Different MII and speed will have
different PCI ID.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added TGL SGMII 1Gbps PCI ID. Different MII and speed will have
different PCI ID.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added EHL SGMII 1Gbps PCI ID. Different MII and speed will have
different PCI ID.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Behún says:
====================
net: dsa: mv88e6xxx: Peridot/Topaz SERDES changes
this is the fifth version of changes for the Topaz/Peridot family of
switches. The patches apply on net-next.
Changes since v4:
- added Reviewed-by and Tested-by tags on first 2 patches, the others
are changed are affected by changes in patch 3/6, so I did not add
the tags, except for 5/6, which is just macro renaming
- patch 3 was changed: the serdes_get_lane returns 0 on success (lane
was discovered), -ENODEV if not lane is present on the port, and
other error if other error occured. Lane is put into a pointer of
type u8
- patches 4 and 6 were affected by this (error detecting from
serdes_get_lane)
- Andrew's complaint about the two additional parameters
(allow_over_2500 and make_cmode_writable) was addressed, by Vivien's
advice: I put a new method into chip operations structure, named
port_set_cmode_writable. This is called from mv88e6xxx_port_setup_mac
just before port_set_cmode. The method is implemented for Topaz.
The check if cmodes over 2500 should be allowed on given port is now
done in the specific port_set_cmode() that requires it, thus the
allow_over_2500 argument is not needed
Again, tested on Turris Mox with Peridot, Topaz, and Peridot + Topaz.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we support SERDES on the Topaz family in a limited way: no
IRQs and the cmode is not writable, thus the mode is determined by
strapping pins.
Marvell's examples though show how to make cmode writable on port 5 and
support SGMII autonegotiation. It is done by writing hidden registers,
for which we already have code.
This patch adds support for making the cmode for the SERDES port
writable on the Topaz family, via a new chip operation,
.port_set_cmode_writable, which is called from mv88e6xxx_port_setup_mac
just before .port_set_cmode.
SERDES IRQs are also enabled for Topaz.
Tested on Turris Mox.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic update. We are removing the last underscore from
macros MV88E6XXX_PORT_STS_CMODE_100BASE_X and
MV88E6XXX_PORT_STS_CMODE_1000BASE_X. The 2500base-x version does not
have that underscore. Also PHY_INTERFACE_MODE_ macros do not have it
there.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
By adding an additional serdes_get_lane implementation (for Topaz), we
can merge the implementations of other SERDES functions (powering and
IRQs). We can skip checking port numbers, since the serdes_get_lane()
methods inform if there is no lane on a port or if the lane cannot be
used for given cmode.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a serdes_get_lane() method in the mv88e6xxx operations structure.
Use it instead of calling the different implementations.
Also change the methods so that their return value is used only for
error. The lane number is put into a place referred to by a pointer
given as argument. If the port does not have a lane, return -ENODEV.
Lanes are phy addresses, so use u8 as their type.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the functions operating on the hidden debug registers
into it's own file, port_hidden.c. The functions prefix is renamed from
mv88e6390_hidden_ to mv88e6xxx_port_hidden_, to be consistent with the
rest of this driver. The macros are prefixed with MV88E6XXX_ prefix, and
are changed not to use the BIT() macro nor bit shifts, since the rest of
the port.h file does not use it.
We also add the support for setting the Block Address field when
operating hidden registers. Marvell's mdio examples for SERDES settings
on Topaz use Block Address 0x7 when reading/writing hidden registers,
and although the specification says that block must be set to 0xf, those
settings are reachable only with Block Address 0x7.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390_serdes_irq_link_sgmii IRQ handler reads the SERDES PHY
status register to determine speed, among other things. If cmode of the
port is set to 2500base-x, though, the PHY still reports 1000 Mbps (the
PHY register itself does not differentiate between 1000 Mbps and 2500
Mbps - it thinks it is running at 1000 Mbps, although clock is 2.5x
faster).
Look at the cmode and set SPEED_2500 if cmode is set to 2500base-x.
Also tell mv88e6xxx_port_setup_mac the PHY interface mode corresponding
to current cmode in terms of phy_interface_t.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long says:
====================
sctp: add SCTP_ECN_SUPPORTED sockopt
This patchset is to make ecn flag per netns and endpoint and then
add SCTP_ECN_SUPPORTED sockopt, as does for other feature flags.
====================
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP_ECN_SUPPORTED sockopt will be added to allow users to change
ep ecn flag, and it's similar with other feature flags.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl net.sctp.ecn_enable is added in this patch. It will allow
users to change the default sctp ecn flag, net.sctp.ecn_enable.
This feature was also required on this thread:
http://lkml.iu.edu/hypermail/linux/kernel/0812.1/01858.html
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add ecn flag for both netns_sctp and sctp_endpoint,
net->sctp.ecn_enable is set 1 by default, and ep->ecn_enable will
be initialized with net->sctp.ecn_enable.
asoc->peer.ecn_capable will be set during negotiation only when
ep->ecn_enable is set on both sides.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/mediatek/mtk_eth_soc.c: In function mtk_handle_irq:
drivers/net/ethernet/mediatek/mtk_eth_soc.c:1951:6: warning: variable status set but not used [-Wunused-but-set-variable]
Fixes: 296c912075 ("net: ethernet: mediatek: Add MT7628/88 SoC support")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Simplify DSA handling of VLAN subinterface offload
Depends on Vivien Didelot's patchset:
https://patchwork.ozlabs.org/project/netdev/list/?series=127197&state=*
This patchset removes a few strange-looking guards for -EOPNOTSUPP in
dsa_slave_vlan_rx_add_vid and dsa_slave_vlan_rx_kill_vid, making that
code path no longer possible.
It also disables the code path for the sja1105 driver, which does
support editing the VLAN table, but not hardware-accelerated VLAN
sub-interfaces, therefore the check in the DSA core would be wrong.
There was no better DSA callback to do this than .port_enable, i.e.
at ndo_open time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch barely supports traffic I/O, and it does that by repurposing
VLANs when there is no bridge that is taking control of them.
Letting DSA declare this netdev feature as supported (see
dsa_slave_create) would mean that VLAN sub-interfaces created on sja1105
switch ports will be hardware offloaded. That means that
net/8021q/vlan_core.c would install the VLAN into the filter tables of
the switch, potentially interfering with the tag_8021q VLANs.
We need to prevent that from happening and not let the 8021q core
offload VLANs to the switch hardware tables. In vlan_filtering=0 modes
of operation, the switch ports can pass through VLAN-tagged frames with
no problem.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding a VLAN sub-interface on a DSA slave port, the 8021q core
checks NETIF_F_HW_VLAN_CTAG_FILTER and, if the netdev is capable of
filtering, calls .ndo_vlan_rx_add_vid or .ndo_vlan_rx_kill_vid to
configure the VLAN offloading.
DSA sets this up counter-intuitively: it always advertises this netdev
feature, but the underlying driver may not actually support VLAN table
manipulation. In that case, the DSA core is forced to ignore the error,
because not being able to offload the VLAN is still fine - and should
result in the creation of a non-accelerated VLAN sub-interface.
Change this so that the netdev feature is only advertised for switch
drivers that support VLAN manipulation, instead of checking for
-EOPNOTSUPP at runtime.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
René van Dorst says:
====================
net: ethernet: mediatek: convert to PHYLINK
These patches converts mediatek driver to PHYLINK API.
v3->v4:
* Phylink improvements and clean-ups after review
v2->v3:
* Phylink improvements and clean-ups after review
v1->v2:
* Rebase for mt76x8 changes
* Phylink improvements and clean-ups after review
* SGMII port doesn't support 2.5Gbit in SGMII mode only in BASE-X mode.
Refactor the code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch the removes the recently added mediatek,physpeed property.
Use the fixed-link property speed = <2500> to set the phy in 2.5Gbit.
See mt7622-bananapi-bpi-r64.dts for a working example.
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Re-add SGMII support but now with PHYLINK API support
So the SGMII changes are more clear
* Move SGMII block setup from mtk_gmac_sgmii_path_setup() to
mtk_mac_config()
* Merge mtk_setup_hw_path() into mtk_mac_config()
* Remove mediatek,physpeed property, fixed-link supports now any speed so
speed = <2500>; is now valid with PHYLINK
* Demagic SGMII register values
* Use phylink state to setup fixed-link mode
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This convert the basics to PHYLINK API.
SGMII support is not in this patch.
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: explicit programmation of VLAN on CPU ports
When a VLAN is programmed on a user port, every switch of the fabric also
program the CPU ports and the DSA links as part of the VLAN. To do that,
DSA makes use of bitmaps to prepare all members of a VLAN.
While this is expected for DSA links which are used as conduit between
interconnected switches, only the dedicated CPU port of the slave must be
programmed, not all CPU ports of the fabric. This may also cause problems in
other corners of DSA such as the tag_8021q.c driver, which needs to program
its ports manually, CPU port included.
We need the dsa_port_vlan_{add,del} functions and its dsa_port_vid_{add,del}
variants to simply trigger the VLAN programmation without any logic in them,
but they may currently skip the operation based on the bridge device state.
This patchset gets rid of the bitmap operations, and moves the bridge device
check as well as the explicit programmation of CPU ports where they belong,
in the slave code.
While at it, clear the VLAN flags before programming a CPU port, as it
doesn't make sense to forward the PVID flag for example for such ports.
Changes in v2: only clear the PVID flag.
====================
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bridge offloads a VLAN on a slave port, we also need to
program its dedicated CPU port as a member of the VLAN.
Drivers may handle the CPU port's membership as they want. For example,
Marvell as a special "Unmodified" mode to pass frames as is through
such ports.
Even though DSA expects the drivers to handle the CPU port membership,
it does not make sense to program user VLANs as PVID on the CPU port.
This patch clears this flag before programming the CPU port.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA currently programs a VLAN on the CPU port implicitly after the
related notifier is received by a switch.
While we still need to do this transparent programmation of the DSA
links in the fabric, programming the CPU port this way may cause
problems in some corners such as the tag_8021q driver.
Because the dedicated CPU port is specific to a slave, make their
programmation explicit a few layers up, in the slave code.
Note that technically, DSA links have a dedicated CPU port as well,
but since they are only used as conduit between interconnected switches
of a fabric, programming them transparently this way is what we want.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge VLANs are not offloaded by dsa_port_vlan_* if the port is
not bridged or if its bridge is not VLAN aware.
This is a good thing but other corners of DSA, such as the tag_8021q
driver, may need to program VLANs regardless the bridge state.
And also because bridge_dev is specific to user ports anyway, move
these checks were it belongs, one layer up in the slave code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dsa_slave_vlan_add and dsa_slave_vlan_del helpers to handle
SWITCHDEV_OBJ_ID_PORT_VLAN switchdev objects. Also copy the
switchdev_obj_port_vlan structure on add since we will modify it in
future patches.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently dsa_port_vid_add returns 0 if the switch returns -EOPNOTSUPP.
This function is used in the tag_8021q.c code to offload the PVID of
ports, which would simply not work if .port_vlan_add is not supported
by the underlying switch.
Do not skip -EOPNOTSUPP in dsa_port_vid_add but only when necessary,
that is to say in dsa_slave_vlan_rx_add_vid.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bitmap operations were introduced to simplify the switch drivers
in the future, since most of them could implement the common VLAN and
MDB operations (add, del, dump) with simple functions taking all target
ports at once, and thus limiting the number of hardware accesses.
Programming an MDB or VLAN this way in a single operation would clearly
simplify the drivers a lot but would require a new get-set interface
in DSA. The usage of such bitmap from the stack also raised concerned
in the past, leading to the dynamic allocation of a new ds->_bitmap
member in the dsa_switch structure. So let's get rid of them for now.
This commit nicely wraps the ds->ops->port_{mdb,vlan}_{prepare,add}
switch operations into new dsa_switch_{mdb,vlan}_{prepare,add}
variants not using any bitmap argument anymore.
New dsa_switch_{mdb,vlan}_match helpers have been introduced to make
clear which local port of a switch must be programmed with the target
object. While the targeted user port is an obvious candidate, the
DSA links must also be programmed, as well as the CPU port for VLANs.
While at it, also remove local variables that are only used once.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In file included from ./arch/powerpc/include/asm/paca.h:15,
from ./arch/powerpc/include/asm/current.h:13,
from ./include/linux/thread_info.h:21,
from ./include/asm-generic/preempt.h:5,
from ./arch/powerpc/include/generated/asm/preempt.h:1,
from ./include/linux/preempt.h:78,
from ./include/linux/spinlock.h:51,
from ./include/linux/wait.h:9,
from ./include/linux/completion.h:12,
from ./include/linux/mlx5/driver.h:37,
from
drivers/net/ethernet/mellanox/mlx5/core/lib/eq.h:6,
from
drivers/net/ethernet/mellanox/mlx5/core/diag/fw_tracer.c:33:
In function 'strncpy',
inlined from 'mlx5_fw_tracer_save_trace' at
drivers/net/ethernet/mellanox/mlx5/core/diag/fw_tracer.c:549:2,
inlined from 'mlx5_tracer_print_trace' at
drivers/net/ethernet/mellanox/mlx5/core/diag/fw_tracer.c:574:2:
./include/linux/string.h:305:9: warning: '__builtin_strncpy' output may
be truncated copying 256 bytes from a string of length 511
[-Wstringop-truncation]
return __builtin_strncpy(p, q, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix it by using the new strscpy_pad() since the commit 458a3bf82d
("lib/string: Add strscpy_pad() function") which will always
NUL-terminate the string, and avoid possibly leak data through the ring
buffer where non-admin account might enable these events through perf.
Fixes: fd1483fe1f ("net/mlx5: Add support for FW reporter dump")
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Highlights include:
Stable fixes:
- Fix a page lock leak in nfs_pageio_resend()
- Ensure O_DIRECT reports an error if the bytes read/written is 0
- Don't handle errors if the bind/connect succeeded
- Revert "NFSv4/flexfiles: Abort I/O early if the layout segment was invalidat
ed"
Bugfixes:
- Don't refresh attributes with mounted-on-file information
- Fix return values for nfs4_file_open() and nfs_finish_open()
- Fix pnfs layoutstats reporting of I/O errors
- Don't use soft RPC calls for pNFS/flexfiles I/O, and don't abort for
soft I/O errors when the user specifies a hard mount.
- Various fixes to the error handling in sunrpc
- Don't report writepage()/writepages() errors twice.
-----BEGIN PGP SIGNATURE-----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=YHhU
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-5.3-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable fixes:
- Fix a page lock leak in nfs_pageio_resend()
- Ensure O_DIRECT reports an error if the bytes read/written is 0
- Don't handle errors if the bind/connect succeeded
- Revert "NFSv4/flexfiles: Abort I/O early if the layout segment was
invalidat ed"
Bugfixes:
- Don't refresh attributes with mounted-on-file information
- Fix return values for nfs4_file_open() and nfs_finish_open()
- Fix pnfs layoutstats reporting of I/O errors
- Don't use soft RPC calls for pNFS/flexfiles I/O, and don't abort
for soft I/O errors when the user specifies a hard mount.
- Various fixes to the error handling in sunrpc
- Don't report writepage()/writepages() errors twice"
* tag 'nfs-for-5.3-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: remove set but not used variable 'mapping'
NFSv2: Fix write regression
NFSv2: Fix eof handling
NFS: Fix writepage(s) error handling to not report errors twice
NFS: Fix spurious EIO read errors
pNFS/flexfiles: Don't time out requests on hard mounts
SUNRPC: Handle connection breakages correctly in call_status()
Revert "NFSv4/flexfiles: Abort I/O early if the layout segment was invalidated"
SUNRPC: Handle EADDRINUSE and ENOBUFS correctly
pNFS/flexfiles: Turn off soft RPC calls
SUNRPC: Don't handle errors if the bind/connect succeeded
NFS: On fatal writeback errors, we need to call nfs_inode_remove_request()
NFS: Fix initialisation of I/O result struct in nfs_pgio_rpcsetup
NFS: Ensure O_DIRECT reports an error if the bytes read/written is 0
NFSv4/pnfs: Fix a page lock leak in nfs_pageio_resend()
NFSv4: Fix return value in nfs_finish_open()
NFSv4: Fix return values for nfs4_file_open()
NFS: Don't refresh attributes with mounted-on-file information
- Support for Edge Triggered IRQs in ARC IDU intc
- other fixes here and there
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CJKr
-----END PGP SIGNATURE-----
Merge tag 'arc-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- support for Edge Triggered IRQs in ARC IDU intc
- other fixes here and there
* tag 'arc-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
arc: prefer __section from compiler_attributes.h
dt-bindings: IDU-intc: Add support for edge-triggered interrupts
dt-bindings: IDU-intc: Clean up documentation
ARCv2: IDU-intc: Add support for edge-triggered interrupts
ARC: unwind: Mark expected switch fall-throughs
ARC: [plat-hsdk]: allow to switch between AXI DMAC port configurations
ARC: fix typo in setup_dma_ops log message
ARCv2: entry: early return from exception need not clear U & DE bits
A collection of small fixes as usual:
- More coverage of USB-audio descriptor sanity checks
- A fix for mute LED regression on Conexant HD-audio codecs
- A few device-specific fixes and quirks for USB-audio and HD-audio
- A fix for (die-hard remaining) possible race in sequencer core
- FireWire oxfw regression fix that was introduced in 5.3-rc1
-----BEGIN PGP SIGNATURE-----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=Cco7
-----END PGP SIGNATURE-----
Merge tag 'sound-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes as usual:
- More coverage of USB-audio descriptor sanity checks
- A fix for mute LED regression on Conexant HD-audio codecs
- A few device-specific fixes and quirks for USB-audio and HD-audio
- A fix for (die-hard remaining) possible race in sequencer core
- FireWire oxfw regression fix that was introduced in 5.3-rc1"
* tag 'sound-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: oxfw: fix to handle correct stream for PCM playback
ALSA: seq: Fix potential concurrent access to the deleted pool
ALSA: usb-audio: Check mixer unit bitmap yet more strictly
ALSA: line6: Fix memory leak at line6_init_pcm() error path
ALSA: usb-audio: Fix invalid NULL check in snd_emuusb_set_samplerate()
ALSA: hda/ca0132 - Add new SBZ quirk
ALSA: usb-audio: Add implicit fb quirk for Behringer UFX1604
ALSA: hda - Fixes inverted Conexant GPIO mic mute led
Pull networking fixes from David Miller:
1) Use 32-bit index for tails calls in s390 bpf JIT, from Ilya
Leoshkevich.
2) Fix missed EPOLLOUT events in TCP, from Eric Dumazet. Same fix for
SMC from Jason Baron.
3) ipv6_mc_may_pull() should return 0 for malformed packets, not
-EINVAL. From Stefano Brivio.
4) Don't forget to unpin umem xdp pages in error path of
xdp_umem_reg(). From Ivan Khoronzhuk.
5) Fix sta object leak in mac80211, from Johannes Berg.
6) Fix regression by not configuring PHYLINK on CPU port of bcm_sf2
switches. From Florian Fainelli.
7) Revert DMA sync removal from r8169 which was causing regressions on
some MIPS Loongson platforms. From Heiner Kallweit.
8) Use after free in flow dissector, from Jakub Sitnicki.
9) Fix NULL derefs of net devices during ICMP processing across
collect_md tunnels, from Hangbin Liu.
10) proto_register() memory leaks, from Zhang Lin.
11) Set NLM_F_MULTI flag in multipart netlink messages consistently,
from John Fastabend.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits)
r8152: Set memory to all 0xFFs on failed reg reads
openvswitch: Fix conntrack cache with timeout
ipv4: mpls: fix mpls_xmit for iptunnel
nexthop: Fix nexthop_num_path for blackhole nexthops
net: rds: add service level support in rds-info
net: route dump netlink NLM_F_MULTI flag missing
s390/qeth: reject oversized SNMP requests
sock: fix potential memory leak in proto_register()
MAINTAINERS: Add phylink keyword to SFF/SFP/SFP+ MODULE SUPPORT
xfrm/xfrm_policy: fix dst dev null pointer dereference in collect_md mode
ipv4/icmp: fix rt dst dev null pointer dereference
openvswitch: Fix log message in ovs conntrack
bpf: allow narrow loads of some sk_reuseport_md fields with offset > 0
bpf: fix use after free in prog symbol exposure
bpf: fix precision tracking in presence of bpf2bpf calls
flow_dissector: Fix potential use-after-free on BPF_PROG_DETACH
Revert "r8169: remove not needed call to dma_sync_single_for_device"
ipv6: propagate ipv6_add_dev's error returns out of ipv6_find_idev
net/ncsi: Fix the payload copying for the request coming from Netlink
qed: Add cleanup in qed_slowpath_start()
...
Fixes gcc '-Wunused-but-set-variable' warning:
fs/nfs/write.c: In function nfs_page_async_flush:
fs/nfs/write.c:609:24: warning: variable mapping set but not used [-Wunused-but-set-variable]
It is not use since commit aefb623c422e ("NFS: Fix
writepage(s) error handling to not report errors twice")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Ensure we update the write result count on success, since the
RPC call itself does not do so.
Reported-by: Jan Stancek <jstancek@redhat.com>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
If we received a reply from the server with a zero length read and
no error, then that implies we are at eof.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Avoids:
../drivers/mfd/rk808.c:771:1: warning: symbol 'rk8xx_pm_ops' \
was not declared. Should it be static?
Fixes: 5752bc4373 ("mfd: rk808: Mark pm functions __maybe_unused")
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Aya Levin
Moshe Shemesh
Maxim Mikityanskiy
Tariq Toukan
Erez Alfasi
Saeed Mahameed
Michael Guralnik
David S. Miller
Voon Weifeng
Marek Behún
Xin Long
Mao Wenan
Vladimir Oltean
René van Dorst
Vivien Didelot
Qian Cai
Linus Torvalds
YueHaibing
Trond Myklebust
Lee Jones