Pull MD fixes from Shaohua Li:
"This fixes several bugs, three of them are marked for stable:
- an initialization issue fixed by Ming
- a bio clone race issue fixed by me
- an async tx flush issue fixed by Ofer
- other cleanups"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
MD: fix warnning for UP case
md/raid5: add thread_group worker async_tx_issue_pending_all
md: simplify code with bio_io_error
md/raid1: fix writebehind bio clone
md: raid1-10: move raid1/raid10 common code into raid1-10.c
md: raid1/raid10: initialize bvec table via bio_add_page()
md: remove 'idx' from 'struct resync_pages'
inefficiencies in the on-disk journal device layout. Another that
makes use of the block layer's on-stack plugging when writing the
journal.
- A dm-bufio fix for the blk_status_t conversion that went in during the
merge window.
- A few DM raid fixes that address correctness when suspending the
device and a validation fix for validation that occurs during device
activation.
- A couple DM zoned target fixes. Important one being the fix to not
use GFP_KERNEL in the IO path due to concerns about deadlock in
low-memory conditions (e.g. swap over a DM zoned device, etc).
- A DM DAX device fix to make sure dm_dax_flush() is called if the
underlying DAX device is operating as a write cache.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZe13OAAoJEMUj8QotnQNav/gIAMXMUbXlYHVikVNq+6rNkXRk
FlsltNcJEDeZCit0nJd/2nOWGpssXdz+7cJTUU28Kp+3IscIolSHS51bzfSFI05V
7LbYqEX1EdXkTwEeYfHlAoOexvj4oarpAWWQF/ACU8rHCruaqfqIa57mstxLoyDY
XcxsIY/fds6GZViLB0MD/jBAKaLWX90aFZ9MQcF7AmdpMr56kCO2PUhiqHcrN47t
BjH7E5QSKGl2pMND1bR6pleWFw8HB7h82Qjaasd5bQuVWseQ4u9Illxny6bhhk2E
BiEWjzFvZB+JL1zl7JIXnBjhdmbwgAVvoW6EqHuVzHuR0X8gylBF2gDLnSzUZu4=
=3MxS
-----END PGP SIGNATURE-----
Merge tag 'for-4.13/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a few DM integrity fixes that improve performance. One that address
inefficiencies in the on-disk journal device layout. Another that
makes use of the block layer's on-stack plugging when writing the
journal.
- a dm-bufio fix for the blk_status_t conversion that went in during
the merge window.
- a few DM raid fixes that address correctness when suspending the
device and a validation fix for validation that occurs during device
activation.
- a couple DM zoned target fixes. Important one being the fix to not
use GFP_KERNEL in the IO path due to concerns about deadlock in
low-memory conditions (e.g. swap over a DM zoned device, etc).
- a DM DAX device fix to make sure dm_dax_flush() is called if the
underlying DAX device is operating as a write cache.
* tag 'for-4.13/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm, dax: Make sure dm_dax_flush() is called if device supports it
dm verity fec: fix GFP flags used with mempool_alloc()
dm zoned: use GFP_NOIO in I/O path
dm zoned: remove test for impossible REQ_OP_FLUSH conditions
dm raid: bump target version
dm raid: avoid mddev->suspended access
dm raid: fix activation check in validate_raid_redundancy()
dm raid: remove WARN_ON() in raid10_md_layout_to_format()
dm bufio: fix error code in dm_bufio_write_dirty_buffers()
dm integrity: test for corrupted disk format during table load
dm integrity: WARN_ON if variables representing journal usage get out of sync
dm integrity: use plugging when writing the journal
dm integrity: fix inefficient allocation of journal space
Pull block fixes from Jens Axboe:
"A small collection of fixes that should go into this series. This
contains:
- NVMe pull request from Christoph, with various fixes for nvme
proper and nvme-fc.
- disable runtime PM for blk-mq for now.
With scsi now defaulting to using blk-mq, this reared its head as
an issue. Longer term we'll fix up runtime PM for blk-mq, for now
just disable it to prevent a hang on laptop resume for some folks.
- blk-mq CPU <-> hw queue map fix from Christoph.
- xen/blkfront pull request from Konrad, with two small fixes for the
blkfront driver.
- a few fixups for nbd from Joseph.
- a stable fix for pblk from Javier"
* 'for-linus' of git://git.kernel.dk/linux-block:
lightnvm: pblk: advance bio according to lba index
nvme: validate admin queue before unquiesce
nbd: clear disconnected on reconnect
nvme-pci: fix HMB size calculation
nvme-fc: revise TRADDR parsing
nvme-fc: address target disconnect race conditions in fcp io submit
nvme: fabrics commands should use the fctype field for data direction
nvme: also provide a UUID in the WWID sysfs attribute
xen/blkfront: always allocate grants first from per-queue persistent grants
xen-blkfront: fix mq start/stop race
blk-mq: map queues to all present CPUs
block: disable runtime-pm for blk-mq
xen-blkfront: Fix handling of non-supported operations
nbd: only set sndtimeo if we have a timeout set
nbd: take tx_lock before disconnecting
nbd: allow multiple disconnects to be sent
- sunxi: Correct time phase settings
- omap_hsmmc: Clean up some dead code
- dw_mmc: Fix message printed for deprecated num-slots DT binding
- dw_mmc: Fix DT documentation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xWHL
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"Here are a couple of mmc fixes intended for v4.13-rc1.
I have also included a couple of cleanup patches in this pull request
for OMAP2+, related to the omap_hsmmc driver. The reason is because of
the changes are also depending on OMAP SoC specific code, so this
simplifies how to deal with this.
Summary:
MMC host:
- sunxi: Correct time phase settings
- omap_hsmmc: Clean up some dead code
- dw_mmc: Fix message printed for deprecated num-slots DT binding
- dw_mmc: Fix DT documentation"
* tag 'mmc-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
Documentation: dw-mshc: deprecate num-slots
mmc: dw_mmc: fix the wrong condition check of getting num-slots from DT
mmc: host: omap_hsmmc: remove unused platform callbacks
ARM: OMAP2+: hsmmc.c: Remove dead code
mmc: sunxi: Keep default timing phase settings for new timing mode
When a lba either hits the cache or corresponds to an empty entry in the
L2P table, we need to advance the bio according to the position in which
the lba is located. Otherwise, we will copy data in the wrong page, thus
causing data corruption for the application.
In case of a cache hit, we assumed that bio->bi_iter.bi_idx would
contain the correct index, but this is no necessarily true. Instead, use
the local bio advance counter and iterator. This guarantees that lbas
hitting the cache are copied into the right bv_page.
In case of an empty L2P entry, we omitted to advance the bio. In the
cases when the same I/O also contains a cache hit, data corresponding
to this lba will be copied to the wrong bv_page. Fix this by advancing
the bio as we do in the case of a cache hit.
Fixes: a4bd217b43 lightnvm: physical block device (pblk) target
Signed-off-by: Javier González <javier@javigon.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch fixes the pop noise in dmic recording using rt5514 on kabylake platform.
This patch enables the rt5514 to use MCLK instead of BLCK as the sysclock which fixes
the pop noise.
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the cracking noise in rt5663 headphones for kabylake platform
by calling rt5663_sel_asrc_clk_src() for RT5663_AD_STEREO_FILTER to set ASRC.
The ASRC function is for asynchronous MCLK and LRCK. For RT5663 ASRC should be
enabled to support special i2s clock format like Intel's 100fs.
ASRC function will track i2s clock and generate a corresponding
system clock for codec. Calling this function helps select the clock source
for both RT5663_AD_STEREO_FILTER and RT5663_DA_STEREO_FILTER filters
which fixes the crackling sound.
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The vast majority of virtual allocations in the vmalloc region are followed
by a guard page, which can help to avoid overruning on vma into another,
which may map a read-sensitive device.
This patch adds a guard page to the end of the kernel image mapping (i.e.
following the data/bss segments).
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The clang warning 'address-of-packed-member' is disabled for the general
kernel code, also disable it for the x86 boot code.
This suppresses a bunch of warnings like this when building with clang:
./arch/x86/include/asm/processor.h:535:30: warning: taking address of
packed member 'sp0' of class or structure 'x86_hw_tss' may result in an
unaligned pointer value [-Waddress-of-packed-member]
return this_cpu_read_stable(cpu_tss.x86_tss.sp0);
^~~~~~~~~~~~~~~~~~~
./arch/x86/include/asm/percpu.h:391:59: note: expanded from macro
'this_cpu_read_stable'
#define this_cpu_read_stable(var) percpu_stable_op("mov", var)
^~~
./arch/x86/include/asm/percpu.h:228:16: note: expanded from macro
'percpu_stable_op'
: "p" (&(var)));
^~~
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170725215053.135586-1-mka@chromium.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=WLqQ
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-v4.13-rc3' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"These iare the fixes for 4.13-rc3: vmwgfx, exynos, i915, amdgpu,
nouveau, host1x and displayport fixes.
As expected people woke up this week, i915 didn't do an -rc2 pull so
got a bumper -rc3 pull, and Ben resurfaced on nouveau and fixed a
bunch of major crashers seen on Fedora 26, and there are a few vmwgfx
fixes as well.
Otherwise exynos had some regression fixes/cleanups, and amdgpu has an
rcu locking regression fix and a couple of minor fixes"
* tag 'drm-fixes-for-v4.13-rc3' of git://people.freedesktop.org/~airlied/linux: (44 commits)
drm/i915: Fix bad comparison in skl_compute_plane_wm.
drm/i915: Force CPU synchronisation even if userspace requests ASYNC
drm/i915: Only skip updating execobject.offset after error
drm/i915: Only mark the execobject as pinned on success
drm/i915: Remove assertion from raw __i915_vma_unpin()
drm/i915/cnl: Fix loadgen select programming on ddi vswing sequence
drm/i915: Fix scaler init during CRTC HW state readout
drm/i915/selftests: Fix an error handling path in 'mock_gem_device()'
drm/i915: Unbreak gpu reset vs. modeset locking
gpu: host1x: Free the IOMMU domain when there is no device to attach
drm/i915: Fix cursor updates on some platforms
drm/i915: Fix user ptr check size in eb_relocate_vma()
drm: exynos: mark pm functions as __maybe_unused
drm/exynos: select CEC_CORE if CEC_NOTIFIER
drm/exynos/hdmi: fix disable sequence
drm/exynos: mic: add a bridge at probe
drm/exynos/dsi: Remove error handling for bridge_node DT parsing
drm/exynos: dsi: do not try to find bridge
drm: exynos: hdmi: make of_device_ids const.
drm: exynos: constify mixer_match_types and *_mxr_drv_data.
...
i915 fixes for -rc3
Bit more than usual since we missed -rc2. 4x cc: stable, 2 gvt
patches, but all fairly minor stuff. Last minute rebase was to add a
few missing cc: stable, I did prep the pull this morning already and
made sure CI approves.
* tag 'drm-intel-fixes-2017-07-27' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Fix bad comparison in skl_compute_plane_wm.
drm/i915: Force CPU synchronisation even if userspace requests ASYNC
drm/i915: Only skip updating execobject.offset after error
drm/i915: Only mark the execobject as pinned on success
drm/i915: Remove assertion from raw __i915_vma_unpin()
drm/i915/cnl: Fix loadgen select programming on ddi vswing sequence
drm/i915: Fix scaler init during CRTC HW state readout
drm/i915/selftests: Fix an error handling path in 'mock_gem_device()'
drm/i915: Unbreak gpu reset vs. modeset locking
drm/i915: Fix cursor updates on some platforms
drm/i915: Fix user ptr check size in eb_relocate_vma()
drm/i915/gvt: Extend KBL platform support in GVT-g
drm/i915/gvt: Fix the vblank timer close issue after shutdown VMs in reverse
Core Changes:
- dp: A few fixes in drm_dp_downstream_debug() (Chris)
- rockchip: sanitize the Kconfig dependencies (fallout from EXTCON) (Arnd)
- host1x: Free the iommu domain when attach_device fails (Paul)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Kocialkowski <contact@paulk.fr>
* tag 'drm-misc-fixes-2017-07-27' of git://anongit.freedesktop.org/git/drm-misc:
gpu: host1x: Free the IOMMU domain when there is no device to attach
drm/rockchip: fix Kconfig dependencies
drm/dp: Don't trust drm_dp_downstream_id()
drm/dp: Fix read pointer for drm_dp_downsteam_debug()
- Add an ACPI module parameter to allow users to override the
new default behavior on some systems where the EC GPE is not
disabled during suspend-to-idle in case the EC on their systems
generates excessive wakeup events and they want to sacrifice
some functionality (like power button wakeups) for extra battery
life while suspended (Rafael Wysocki).
- Fix flushing of the outstanding EC work in the ACPI core
suspend-to-idle code (Rafael Wysocki).
- Add a missing include and fix a messed-up comment in the ACPI
NUMA code (Ross Zwisler).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=m4S0
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These are two fixups for the suspend-to-idle handling in the ACPI
subsystem after recent changes in that area and two simple fixes of
the ACPI NUMA code.
Specifics:
- Add an ACPI module parameter to allow users to override the new
default behavior on some systems where the EC GPE is not disabled
during suspend-to-idle in case the EC on their systems generates
excessive wakeup events and they want to sacrifice some
functionality (like power button wakeups) for extra battery life
while suspended (Rafael Wysocki).
- Fix flushing of the outstanding EC work in the ACPI core
suspend-to-idle code (Rafael Wysocki).
- Add a missing include and fix a messed-up comment in the ACPI NUMA
code (Ross Zwisler)"
* tag 'acpi-4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: NUMA: Fix typo in the full name of SRAT
ACPI: NUMA: add missing include in acpi_numa.h
ACPI / PM / EC: Flush all EC work in acpi_freeze_sync()
ACPI / EC: Add parameter to force disable the GPE on suspend
* acpi-pm:
ACPI / PM / EC: Flush all EC work in acpi_freeze_sync()
ACPI / EC: Add parameter to force disable the GPE on suspend
* acpi-numa:
ACPI: NUMA: Fix typo in the full name of SRAT
ACPI: NUMA: add missing include in acpi_numa.h
ddb_allocation && ddb_allocation / blocks_per_line >= 1 is the same
as ddb_allocation >= blocks_per_line, so use the latter to simplify
this.
This fixes the following compiler warning:
drivers/gpu/drm/i915/intel_pm.c:4467]: (warning) Comparison of a
boolean expression with an integer other than 0 or 1.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: d555cb5827 ("drm/i915/skl+: use linetime latency if ddb size is not available")
Cc: "Mahesh Kumar" <mahesh1.kumar@intel.com>
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: David Binderman <dcb314@hotmail.com>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.13-rc1+
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
(cherry picked from commit 54d20ed1ff)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170717111355.4523-1-maarten.lankhorst@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The goal here was to minimise doing any thing or any check inside the
kernel that was not strictly required. For a userspace that assumes
complete control over the cache domains, the kernel is usually using
outdated information and may trigger clflushes where none were
required.
However, swapping is a situation where userspace has no knowledge of the
domain transfer, and will leave the object in the CPU cache. The kernel
must flush this out to the backing storage prior to use with the GPU. As
we use an asynchronous task tracked by an implicit fence for this, we
also need to cancel the ASYNC flag on the object so that the object will
wait for the clflush to complete before being executed. This also absolves
userspace of the responsibility imposed by commit 77ae995789 ("drm/i915:
Enable userspace to opt-out of implicit fencing") that its needed to ensure
that the object was out of the CPU cache prior to use on the GPU.
Fixes: 77ae995789 ("drm/i915: Enable userspace to opt-out of implicit fencing")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101571
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721145037.25105-5-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 0f46daa1a2)
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I was being overly paranoid in not updating the execobject.offset after
performing the fallback copy where we set reloc.presumed_offset to -1.
The thinking was to ensure that a subsequent NORELOC execbuf would be
forced to process the invalid relocations. However this is overkill so
long as we *only* update the execobject.offset following a successful
update of the relocation value witin the batch. If we have to repeat the
execbuf due to a later interruption, then we may skip the relocations on
the second pass (honouring NORELOC) since the execobject.offset match
the actual offsets (even though reloc.presumed_offset is garbage).
Subsequent calls to execbuf with NORELOC should themselves ensure that
the reloc.presumed_offset have been corrected in case of future
migration.
Reporting back the actual execobject.offset, even when
reloc.presumed_offset is garbage, ensures that reuse of those objects
use the latest information to avoid relocations.
Fixes: 2889caa923 ("drm/i915: Eliminate lots of iterations over the execobjects array")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101635
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721145037.25105-4-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 1f727d9e72)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After we detect a i915_vma pin overflow, we call __i915_vma_unpin to
cleanup. However, on an overflow the pin_count bitfield will be zero,
triggering an assertion, even though we the intention is to merely warn
and report the error back to the user (as historically the culprit has
be a leak in the display code).
Fixes: 20dfbde463 ("drm/i915: Wrap vma->pin_count accessors with small inline helpers")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721145037.25105-2-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 67fddd902b)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The condition for setting the Loadgen Select bit of
PORT_TX_DW4 register during DDI Vswing Sequence should be
Bit rate <=6 GHz whereas the existing code checks only
Bit Rate < 6GHz. This patch fixes this condition.
While at it also remove the redundant paranthesis.
Fixes: cf54ca8bc5 ("drm/i915/cnl: Implement voltage swing sequence.")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1500329122-32662-1-git-send-email-manasi.d.navare@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit a8e45a1c42)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The scaler allocation code depends on a non-zero default value for the
crtc scaler_id, so make sure we initialize the scaler state accordingly
even if the crtc is off. This fixes at least an initial YUV420 modeset
(added in a follow-up patchset by Shashank) when booting with the screen
off: after the initial HW readout and modeset which enables the scaler a
subsequent modeset will disable the scaler which isn't properly
allocated. This results in a funky HW state where the pipe scaler HW
registers can't be modified and the normally black screen is grey and
shifted to the right or jitters.
The problem was revealed by Shashank's YUV420 patchset and first
reported by Ville.
v2:
- In the stable tag also include versions which need backporting (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chandra Konduru <chandra.konduru@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: <stable@vger.kernel.org> # 4.2.x
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: a1b2278e4d ("drm/i915: skylake panel fitting using shared scalers")
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170720112820.26816-1-imre.deak@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 5fb9dadf33)
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Goto the right label in case of error, otherwise there is a leak.
This has been introduced by c5cf9a9147. In this patch a goto has not been
updated.
Fixes: c5cf9a9147 ("drm/i915: Create a kmem_cache to allocate struct i915_priolist from")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20170719223503.30580-1-christophe.jaillet@wanadoo.fr
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit a5ec7fe81a)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Taking the modeset locks unconditionally isn't the greatest idea,
because atm that part is still broken and times out (and then atomic
keels over). And there's really no reason to do so, the old code
didn't do that either.
To make the patch a bit simpler let's also nuke 2 cases that are only
around for the old mmioflip paths. Atomic nonblocking workers will not
die (minus bugs) when a gpu reset happens.
And of course this doesn't fix any of the gpu reset vs. modeset
deadlock fun, but it at least stop modern CI machines from keeling
over all over the place for no reason at all.
And we still have the explicit testcases to run the fake gpu reset, so
coverage isn't that much worse.
v2: Split out additional changes on top, restrict this to purely reducing
the critical section of modeset locks.
v2: Review from Maarten
- update comments
- don't oops when state is NULL in intel_finish_reset, but try to at
least still drop locks properly. The hw is going to be toast anyway.
Fixes: 7397489399 ("drm/i915: Fix modeset handling during gpu reset, v5.")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170719125502.25696-3-daniel.vetter@ffwll.ch
(cherry picked from commit ce87ea15eb)
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull parisc fixes from Helge Deller:
- The majority of lines changed are due to regenerated defconfig files.
- The support for the Page Deallocation Table (PDT) which was merged in
the merge window for 4.13 contained a bug which crashes the kernel if
a bad page is reported by firmware. This is now fixed and the kernel
messages will show which memory slot holds the broken DIMM.
- Commit 3a166fc2d4 ("kbuild: handle libs-y archives separately from
built-in.o archives") broke linking the parisc kernel due to
millicode symbols which can't be reached then any longer. This was
fixed by modifying the parisc vmlinux.lds linker script.
- If the stack checker panics on stack overflow, avoid recursive
panics.
- Some parisc machines can't physically power off and thus instead
start after some time to flood the console by presumably detected
soft lockups. Avoid this by disabling the lockup detectors before
entering the endless for-next loop.
- Dave Anglin provided fixes which prevents TLB speculation on flushed
pages on PA8800/PA9000 CPUs.
- Arvind Yadav sent a trivial patch to constify the attribute_group
structure in our firmware on-board-flash storage driver
(pdc_stable.c)
* 'parisc-4.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Extend disabled preemption in copy_user_page
parisc: Prevent TLB speculation on flushed pages on CPUs that only support equivalent aliases
parisc: Suspend lockup detectors before system halt
parisc: Show DIMM slot number which holds broken memory module
parisc: Add function to return DIMM slot of physical address
parisc: Fix crash when calling PDC_PAT_MEM PDT firmware function
parisc: regenerate defconfig files
parisc: pdc_stable: constify attribute_group structures.
parisc: Merge millicode routines via linker script
parisc: Disable further stack checks when panic occurs during stack check
Instead of fiddling with masking the event channels during suspend
and resume handling let do the irq subsystem do its job. It will do
the mask and unmask operations as needed.
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Remove unnecessary static on local variables last_frontswap_pages and
tgt_frontswap_pages. Such variables are initialized before being used,
on every execution path throughout the function. The statics have no
benefit and, removing them reduce the code size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
You can see a significant difference in the code size after executing
the size command, before and after the code change:
before:
text data bss dec hex filename
5633 3452 384 9469 24fd drivers/xen/xen-selfballoon.o
after:
text data bss dec hex filename
5576 3308 256 9140 23b4 drivers/xen/xen-selfballoon.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
On systems that are not booted as a Xen domain, the xenfs driver prints
the following message during boot.
[ 3.460595] xenfs: not registering filesystem on non-xen platform
As the user chose not to boot a Xen domain, this message does not
provide useful information. Drop this message.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
This is a pretty boring pull request, containing a few HD-audio
quirks and ID updates as usual suspects, as well as a fix for a
regression of FM801 chip on ia64 (what a legacy combination!)
-----BEGIN PGP SIGNATURE-----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=y0Ak
-----END PGP SIGNATURE-----
Merge tag 'sound-4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This is a pretty boring pull request, containing a few HD-audio quirks
and ID updates as usual suspects, as well as a fix for a regression of
FM801 chip on ia64 (what a legacy combination!)"
* tag 'sound-4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Add mute led support for HP ProBook 440 G4
ALSA: hda/realtek - No loopback on ALC225/ALC295 codec
ALSA: hda/realtek - Update headset mode for ALC225
ALSA: fm801: Initialize chip after IRQ handler is registered
ALSA: hda/realtek - Update headset mode for ALC298
ALSA: hda - Add missing NVIDIA GPU codec IDs to patch table
Pull ARM fixes from Russell King:
"Two areas addressed by these fixes:
- Fixes from Dave Martin for the signal frames that were broken with
certain configurations. No one noticed until recently.
- More kexec fixes to ensure that the crashkernel region is correctly
allocated, and a fix for the location of the device tree when
several kexec kernels are loaded"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8687/1: signal: Fix unparseable iwmmxt_sigframe in uc_regspace[]
ARM: 8686/1: iwmmxt: Add missing __user annotations to sigframe accessors
ARM: kexec: fix failure to boot crash kernel
ARM: kexec: avoid allocating crashkernel region outside lowmem
posix_fallocate() will allocate space in an NFS file by considering
the last byte of every 4K block. If it is before EOF, it will read
the byte and if it is zero, a zero is written out. If it is after EOF,
the zero is unconditionally written.
For the blocks beyond EOF, if NFS believes its cache is valid, it will
expand these writes to write full pages, and then will merge the pages.
This results if (typically) 1MB writes. If NFS believes its cache is
not valid (particularly if NFS_INO_INVALID_DATA or
NFS_INO_REVAL_PAGECACHE are set - see nfs_write_pageuptodate()), it will
send the individual 1-byte writes. This results in (typically) 256 times
as many RPC requests, and can be substantially slower.
Currently nfs_revalidate_mapping() is only used when reading a file or
mmapping a file, as these are times when the content needs to be
up-to-date. Writes don't generally need the cache to be up-to-date, but
writes beyond EOF can benefit, particularly in the posix_fallocate()
case.
So this patch calls nfs_revalidate_mapping() when writing beyond EOF -
i.e. when there is a gap between the end of the file and the start of
the write. If the cache is thought to be out of date (as happens after
taking a file lock), this will cause a GETATTR, and the two flags
mentioned above will be cleared. With this, posix_fallocate() on a
newly locked file does not generate excessive tiny writes.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Prior to commit ca0daa277a ("NFS: Cache aggressively when file is open
for writing"), NFS would revalidate, or invalidate, the file size when
taking a lock. Since that commit it only invalidates the file content.
If the file size is changed on the server while wait for the lock, the
client will have an incorrect understanding of the file size and could
corrupt data. This particularly happens when writing beyond the
(supposed) end of file and can be easily be demonstrated with
posix_fallocate().
If an application opens an empty file, waits for a write lock, and then
calls posix_fallocate(), glibc will determine that the underlying
filesystem doesn't support fallocate (assuming version 4.1 or earlier)
and will write out a '0' byte at the end of each 4K page in the region
being fallocated that is after the end of the file.
NFS will (usually) detect that these writes are beyond EOF and will
expand them to cover the whole page, and then will merge the pages.
Consequently, NFS will write out large blocks of zeroes beyond where it
thought EOF was. If EOF had moved, the pre-existing part of the file
will be over-written. Locking should have protected against this,
but it doesn't.
This patch restores the use of nfs_zap_caches() which invalidated the
cached attributes. When posix_fallocate() asks for the file size, the
request will go to the server and get a correct answer.
cc: stable@vger.kernel.org (v4.8+)
Fixes: ca0daa277a ("NFS: Cache aggressively when file is open for writing")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
When there is no device to attach to the IOMMU domain, as may be the
case when the device-tree does not contain the proper iommu node, it is
best to keep going without IOMMU support rather than failing.
This allows the driver to probe and function instead of taking down
all of the tegra drm driver, leading to missing display support.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Fixes: 404bfb78da ("gpu: host1x: Add IOMMU support")
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170710193305.5987-1-contact@paulk.fr
dwmmc host driver already deprecate it in the driver
but didn't modify the documentation to reflect the fact.
This patch deprecates it and clean up num-slots from the
examples of all variant host drivers.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Fixes: d30a8f7bdf ("mmc: dw_mmc: deprecated the "num-slots" property")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change to print the information about when the deprecated "num-slots" DT
binding is being used, as to avoid confusion when browsing the log:
dwmmc_rockchip fe320000.dwmmc: 'num-slots' was deprecated.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: d30a8f7bdf ("mmc: dw_mmc: deprecated the "num-slots" property")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
That commit was part of the changes moving x86 to the generic CPU hotplug
interrupt migration code. The force flag was required on x86 before the
hierarchical irqdomain rework, but invoking set_affinity() with force=true
stayed and had no side effects.
At some point in the past, the force flag got repurposed to support the
exynos timer interrupt affinity setting to a not yet online CPU, so the
interrupt controller callback does not verify the supplied affinity mask
against cpu_online_mask.
Setting the flag in the CPU hotplug code causes the cpu online masking to
be blocked on these irq controllers and results in potentially affining an
interrupt to the CPU which is unplugged, i.e. instead of moving it away,
it's just reassigned to it.
As the force flags is not longer needed on x86, it's safe to revert that
patch so the ARM irqchips which use the force flag work again.
Add comments to that effect, so this won't happen again.
Note: The online mask handling should be done in the generic code and the
force flag and the masking in the irq chips removed all together, but
that's not a change possible for 4.13.
Fixes: 77f85e66aa ("genirq/cpuhotplug: Set force affinity flag on hotplug migration")
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: LAK <linux-arm-kernel@lists.infradead.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1707271217590.3109@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since the PMU register interface is banked per CPU, CPU PMU interrrupts
cannot be handled by a CPU other than the one with the PMU asserting the
interrupt. This means that migrating PMU SPIs, as we do during a CPU
hotplug operation doesn't make any sense and can lead to the IRQ being
disabled entirely if we route a spurious IRQ to the new affinity target.
This has been observed in practice on AMD Seattle, where CPUs on the
non-boot cluster appear to take a spurious PMU IRQ when coming online,
which is routed to CPU0 where it cannot be handled.
This patch passes IRQF_PERCPU for PMU SPIs and forcefully sets their
affinity prior to requesting them, ensuring that they cannot
be migrated during hotplug events. This interacts badly with the DB8500
erratum workaround that ping-pongs the interrupt affinity from the handler,
so we avoid passing IRQF_PERCPU in that case by allowing the IRQ flags
to be overridden in the platdata.
Fixes: 3cf7ee98b8 ("drivers/perf: arm_pmu: move irq request/free into probe")
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Turns out that just writing CURPOS isn't sufficient to move the cursor
on some platforms. My 830 works just fine, but eg. 945 and PNV don't.
On those platforms we need to arm even the CURPOS update with a
CURBASE write.
Even worse, a write to any of the cursor register apart from CURBASE
will cancel an already pending cursor update. So if we have armed a
CURCNTR/CURBASE update, a subsequent CURPOS write prior to vblank
would cancel that armed update. Thus we're left with a cursor that
doesn't appear to move, or even change shape.
Fix the problem by always performing the CURBASE write after a
CURPOS write. Bspec is somewhat unclear which platforms actually
require this CURBASE write and which don't. So to keep it simple
and to make sure we really fix the problem across all supported
devices, let's just perform the CURBASE write unconditionally.
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101790
Fixes: 75343a44c9 ("drm/i915: Drop useless posting reads from cursor commit")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170714155227.6089-1-ville.syrjala@linux.intel.com
(cherry picked from commit 8753d2bc5e)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the sizeof(ptr) vs. sizeof(*ptr) typo.
Fixes: 2889caa923 ("drm/i915: Eliminate lots of iterations over the execobjects array")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170714151242.517-2-imre.deak@intel.com
(cherry picked from commit edd9003f7f)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes: dad6f37c26 ("powerpc: subpage_protect: Increase the array size to take care of 64TB")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Tested-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The rework of the exynos DRM clock handling introduced
warnings for configurations that have CONFIG_PM disabled:
drivers/gpu/drm/exynos/exynos_hdmi.c:736:13: error: 'hdmi_clk_disable_gates' defined but not used [-Werror=unused-function]
static void hdmi_clk_disable_gates(struct hdmi_context *hdata)
^~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/exynos/exynos_hdmi.c:717:12: error: 'hdmi_clk_enable_gates' defined but not used [-Werror=unused-function]
static int hdmi_clk_enable_gates(struct hdmi_context *hdata)
The problem is that the PM functions themselves are inside of
an #ifdef, but some functions they call are not.
This patch removes the #ifdef and instead marks the PM functions
as __maybe_unused, which is a more reliable way to get it right.
Link: https://patchwork.kernel.org/patch/8436281/
Fixes: 9be7e98984 ("drm/exynos/hdmi: clock code re-factoring")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
If the s5p-cec driver is a module and the drm exynos driver is built-in, then
the CEC core will be a module also, causing the CEC notifier to fail (will be
compiled as empty functions).
To prevent this select CEC_CORE if CEC_NOTIFIER is set to ensure the CEC core
is also built into the kernel.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The "Fixes" patch was incorrectly merged, as a result PHY is prematurely
powered off and for example Odroid-U3 cannot disable TV power domain
when HDMI cable is unplugged.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 625e63e2 ("drm/exynos/hdmi: fix pipeline disable order")
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch moves drm_bridge_add call into probe.
It doesn't need to call drm_bridge_add call every time
bind callback is called.
Changelog v2
- moved drm_bridge_remove call into remove callback.
- corrected description.
Suggested-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Remove the error handling of bridge_node because the bridge_node is
optional.
For example, In case of Exynos SoC, a bridge device such as mDNIe and
MIC could be placed between Display Controller and MIPI DSI device but
the bridge device is optional.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
It doesn't need to try to find a bridge if bridge node doesn't exist.
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Tested-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
12294 1192 0 13486 34ae drivers/gpu/drm/exynos/exynos_hdmi.o
File size after constify hdmi_match_types.
text data bss dec hex filename
13318 176 0 13494 34b6 drivers/gpu/drm/exynos/exynos_hdmi.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Linus Torvalds
Javier González
Harsha Priya N
Will Deacon
Matthias Kaehlcke
Dave Airlie
Rafael J. Wysocki
Daniel Vetter
Maarten Lankhorst
Chris Wilson
Navare, Manasi D
Imre Deak
Christophe JAILLET
Juergen Gross
Gustavo A. R. Silva
Punit Agrawal
NeilBrown
Paul Kocialkowski
Shawn Lin
Jens Axboe
Thomas Gleixner
Ville Syrjälä
Aneesh Kumar K.V
Arnd Bergmann
Hans Verkuil
Andrzej Hajda
Inki Dae
Hoegeun Kwon
Arvind Yadav