This patch rearranges the SIT DF bit handling using the new IPIP DF
code. The only externally visible effect should be the case where
PMTU is enabled and the MTU is exactly 1280 bytes. In this case the
previous code would send packets out with DF off while the new code
would set the DF bit. This is inline with RFC 4213.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks,
Signed-off-by: David S. Miller <davem@davemloft.net>
Apparently, inet6_dump_addr() is not able to handle more than
64 ipv6 addresses per device. We must break from inner loops
in case skb is full, or else cursor is put at the end of list.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling large number of netdevice, inet6_dump_ifinfo()
is very slow because it has O(N^2) complexity.
Instead of scanning one single list, we can use the 256 sub lists
of the dev_index hash table, and RCU lookups.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use guard DECLARE_SOCKADDR in a few more places which allow
us to catch if the structure copied back is too big.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP bind() can be O(N^2) in some pathological cases.
Thanks to secondary hash tables, we can make it O(N)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following bug in the current implementation of
net/xfrm: SAD entries timeouts do not count the time spent by the machine
in the suspended state. This leads to the connectivity problems because
after resuming local machine thinks that the SAD entry is still valid, while
it has already been expired on the remote server.
The cause of this is very simple: the timeouts in the net/xfrm are bound to
the old mod_timer() timers. This patch reassigns them to the
CLOCK_REALTIME hrtimer.
I have been using this version of the patch for a few months on my
machines without any problems. Also run a few stress tests w/o any
issues.
This version of the patch uses tasklet_hrtimer by Peter Zijlstra
(commit 9ba5f0).
This patch is against 2.6.31.4. Please CC me.
Signed-off-by: Yury Polyanskiy <polyanskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds compat_ioctl support for SIOCWANDEV, which has
always been missing.
The definition of struct compat_ifreq was missing an
ifru_settings fields that is needed to support SIOCWANDEV,
so add that and clean up the whitespace damage in the
struct definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
SIOCGMIIPHY and SIOCGMIIREG return data through ifreq,
so it needs to be converted on the way out as well.
SIOCGIFPFLAGS is unused, but has the same problem in theory.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When skb_clone() fails, we should increment sk_drops and SNMP counters.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPV6 UDP multicast rx path is a bit complex and can hold a spinlock
for a long time.
Using a small (32 or 64 entries) stack of socket pointers can help
to perform expensive operations (skb_clone(), udp_queue_rcv_skb())
outside of the lock, in most cases.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP multicast rx path is a bit complex and can hold a spinlock
for a long time.
Using a small (32 or 64 entries) stack of socket pointers can help
to perform expensive operations (skb_clone(), udp_queue_rcv_skb())
outside of the lock, in most cases.
It's also a base for a future RCU conversion of multicast recption.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Lucian Adrian Grijincu <lgrijincu@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We first locate the (local port) hash chain head
If few sockets are in this chain, we proceed with previous lookup algo.
If too many sockets are listed, we take a look at the secondary
(port, address) hash chain.
We choose the shortest chain and proceed with a RCU lookup on the elected chain.
But, if we chose (port, address) chain, and fail to find a socket on given address,
we must try another lookup on (port, in6addr_any) chain to find sockets not bound
to a particular IP.
-> No extra cost for typical setups, where the first lookup will probabbly
be performed.
RCU lookups everywhere, we dont acquire spinlock.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We first locate the (local port) hash chain head
If few sockets are in this chain, we proceed with previous lookup algo.
If too many sockets are listed, we take a look at the secondary
(port, address) hash chain we added in previous patch.
We choose the shortest chain and proceed with a RCU lookup on the elected chain.
But, if we chose (port, address) chain, and fail to find a socket on given address,
we must try another lookup on (port, INADDR_ANY) chain to find socket not bound
to a particular IP.
-> No extra cost for typical setups, where the first lookup will probabbly
be performed.
RCU lookups everywhere, we dont acquire spinlock.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extends udp_table to contain a secondary hash table.
socket anchor for this second hash is free, because UDP
doesnt use skc_bind_node : We define an union to hold
both skc_bind_node & a new hlist_nulls_node udp_portaddr_node
udp_lib_get_port() inserts sockets into second hash chain
(additional cost of one atomic op)
udp_lib_unhash() deletes socket from second hash chain
(additional cost of one atomic op)
Note : No spinlock lockdep annotation is needed, because
lock for the secondary hash chain is always get after
lock for primary hash chain.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Union sk_hash with two u16 hashes for udp (no extra memory taken)
One 16 bits hash on (local port) value (the previous udp 'hash')
One 16 bits hash on (local address, local port) values, initialized
but not yet used. This second hash is using jenkin hash for better
distribution.
Because the 'port' is xored later, a partial hash is performed
on local address + net_hash_mix(net)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a counter in udp_hslot to keep an accurate count
of sockets present in chain.
This will permit to upcoming UDP lookup algo to chose
the shortest chain when secondary hash is added.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no good reason to not support userspace specifying the
network namespace during device creation, and it makes it easier
to create a network device and pass it to a child network namespace
with a well known name.
We have to be careful to ensure that the target network namespace
for the new device exists through the life of the call. To keep
that logic clear I have factored out the network namespace grabbing
logic into rtnl_link_get_net.
In addtion we need to continue to pass the source network namespace
to the rtnl_link_ops.newlink method so that we can find the base
device source network namespace.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
atalk_sum_partial can now use the rol16 function in bitops.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using RCU helps not touching device refcount in rawv6_bind()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_proc_getifname() is called with RTNL and dev_base_lock
not held. It calls __dev_get_by_index() without locks, and
this is illegal (might crash)
Close the race by holding dev_base_lock and copying dev->name
in the protected section.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The x25 driver uses lock_kernel() implicitly through
its proto_ops wrapper. The makes the usage explicit
in order to get rid of that wrapper and to better document
the usage of the BKL.
The next step should be to get rid of the usage of the BKL
in x25 entirely, which requires understanding what data
structures need serialized accesses.
Cc: Henner Eisen <eis@baty.hanse.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-x25@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The irda driver uses the BKL implicitly in its protocol
operations. Replace the wrapped proto_ops with explicit
lock_kernel() calls makes the usage more obvious and
shrinks the size of the object code.
The calls t lock_kernel() should eventually all be replaced
by other serialization methods, which requires finding out
The calls t lock_kernel() should eventually all be replaced
by other serialization methods, which requires finding out
which data actually needs protection.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Making the BKL usage explicit in ipx makes it more
obvious where it is used, reduces code size and helps
getting rid of the BKL in common code.
I did not analyse how to kill lock_kernel from ipx
entirely, this will involve either proving that it's not
needed, or replacing with a proper mutex or spinlock,
after finding out which data structures are protected
by the lock.
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Making the BKL usage explicit in appletalk makes it more
obvious where it is used, reduces code size and helps
getting rid of the BKL in common code.
I did not analyse how to kill lock_kernel from appletalk
entirely, this will involve either proving that it's not
needed, or replacing with a proper mutex or spinlock,
after finding out which data structures are protected
by the lock.
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
SPIN_LOCK_UNLOCKED is deprecated. Use DEFINE_SPINLOCK instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MII ioctls and SIOCSIFNAME need to go through ifsioc conversion,
which they never did so far. Some others are not implemented in the
native path, so we can just return -EINVAL directly.
Add IFSLAVE ioctls to the EINVAL list and move it to the end to
optimize the code path for the common case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the original socket compat_ioctl code
from fs/compat_ioctl.c and converts the code from the copy
in net/socket.c into a single function. We add a few cycles
of runtime to compat_sock_ioctl() with the long switch()
statement, but gain some cycles in return by simplifying
the call chain to get there.
Due to better inlining, save 1.5kb of object size in the
process, and enable further savings:
before:
text data bss dec hex filename
13540 18008 2080 33628 835c obj/fs/compat_ioctl.o
14565 636 40 15241 3b89 obj/net/socket.o
after:
text data bss dec hex filename
8916 15176 2080 26172 663c obj/fs/compat_ioctl.o
20725 636 40 21401 5399 obj/net/socket.o
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must not have a compat ioctl handler for SIOCATALKDIFADDR
in common code, because the same number is used in other protocols
with different data structures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes an identical copy of the socket compat_ioctl code
from fs/compat_ioctl.c to net/socket.c, as a preparation
for moving the functionality in a way that can be easily
reviewed.
The code is hidden inside of #if 0 and gets activated in the
patch that will make it work.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 2003 requires the outer header to have DF set if DF is set
on the inner header, even when PMTU discovery is off for the
tunnel. Our implementation does exactly that.
For this to work properly the IPIP gateway also needs to engate
in PMTU when the inner DF bit is set. As otherwise the original
host would not be able to carry out its PMTU successfully since
part of the path is only visible to the gateway.
Unfortunately when the tunnel PMTU discovery setting is off, we
do not collect the necessary soft state, resulting in blackholes
when the original host tries to perform PMTU discovery.
This problem is not reproducible on the IPIP gateway itself as
the inner packet usually has skb->local_df set. This is not
correctly cleared (an unrelated bug) when the packet passes
through the tunnel, which allows fragmentation to occur. For
hosts behind the IPIP gateway it is readily visible with a simple
ping.
This patch fixes the problem by performing PMTU discovery for
all packets with the inner DF bit set, regardless of the PMTU
discovery setting on the tunnel itself.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit v2.6.28-rc1~717^2~109^2~2 was slightly incomplete; not all
instances of par->match->family were changed to par->family.
References: http://bugzilla.netfilter.org/show_bug.cgi?id=610
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices require that all frames to a station
are flushed when that station goes into powersave
mode before being able to send frames to that
station again when it wakes up or polls -- all in
order to avoid reordering and too many or too few
frames being sent to the station when it polls.
Normally, this is the case unless the station
goes to sleep and wakes up very quickly again.
But in that case, frames for it may be pending
on the hardware queues, and thus races could
happen in the case of multiple hardware queues
used for QoS/WMM. Normally this isn't a problem,
but with the iwlwifi mechanism we need to make
sure the race doesn't happen.
This makes mac80211 able to cope with the race
with driver help by a new WLAN_STA_PS_DRIVER
per-station flag that can be controlled by the
driver and tells mac80211 whether it can transmit
frames or not. This flag must be set according to
very specific rules outlined in the documentation
for the function that controls it.
When we buffer new frames for the station, we
normally set the TIM bit right away, but while
the driver has blocked transmission to that sta
we need to avoid that as well since we cannot
respond to the station if it wakes up due to the
TIM bit. Once the driver unblocks, we can set
the TIM bit.
Similarly, when the station just wakes up, we
need to wait until all other frames are flushed
before we can transmit frames to that station,
so the same applies here, we need to wait for
the driver to give the OK.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for two more NL802154 commands: ADD_IFACE and DEL_IFACE,
thus allowing creation and removal of logic WPAN interfaces on the top
of wpan-phy.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Move all mac-related stuff to separate file so that ieee802154/netlink.c
contains only generic code.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
There is no real need to have ieee802154 interfaces separate
into several small modules, as neither of them has it's own use.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Follow the usual pattern of devices registration by adding new function
(wpan_phy_set_dev) that sets child->parent relationship and removing
parent argument from wpan_phy_register call.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
IEEE 802.15.4-2006 defines channel pages that hold channels (max 32 pages,
27 channels per page). Allow the driver to specify supported channels
on pages, other than the first one.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Set page to zero (for compatibility w/ devices supporting only first page).
Also init channel by default to -1 to disallow transfers for non-initialised
devices.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Conflicts:
drivers/net/usb/cdc_ether.c
All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on device refcount stuff, I found a device refcount leak
through DECNET.
This nasty bug can be used to hold refcounts on any !DECNET netdevice.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitezslav Samel discovered that since 2.6.30.4+ active FTP can not work
over NAT. The "cause" of the problem was a fix of unacknowledged data
detection with NAT (commit a3a9f79e36).
However, actually, that fix uncovered a long standing bug in TCP conntrack:
when NAT was enabled, we simply updated the max of the right edge of
the segments we have seen (td_end), by the offset NAT produced with
changing IP/port in the data. However, we did not update the other parameter
(td_maxend) which is affected by the NAT offset. Thus that could drift
away from the correct value and thus resulted breaking active FTP.
The patch below fixes the issue by *not* updating the conntrack parameters
from NAT, but instead taking into account the NAT offsets in conntrack in a
consistent way. (Updating from NAT would be more harder and expensive because
it'd need to re-calculate parameters we already calculated in conntrack.)
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/core/sock.c: In function 'sock_setsockopt':
net/core/sock.c:396: warning: 'index' may be used uninitialized in this function
net/core/sock.c:396: note: 'index' was declared here
GCC can't see that all paths initialize index, so just
set it to the default (0) and eliminate the specific
code block that handles the null device name string.
Signed-off-by: David S. Miller <davem@davemloft.net>
cur_pkt_size can be changed in proc fs while pktgen is running,
we better use a private field to get precise tx-bytes counter.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid dev_hold()/dev_put() in sock_bindtodevice()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending fragmentation expiration ICMP V4/V6 messages,
we can avoid touching device refcount, thanks to RCU
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We hold RTNL in tc_dump_tfilter(), we can avoid dev_hold()/dev_put()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid touching device refcount in sctp/ipv6, thanks to RCU
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_get_by_name_rcu() to avoid dev_put() calls,
in sections already inside a rcu_read_lock()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add_del_if() is called with RTNL, we can use __dev_get_by_index()
instead of [dev_get_by_index() + dev_put()]
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before calling capable(CAP_NET_RAW) check if this operations is on behalf
of the kernel or on behalf of userspace. Do not do the security check if
it is on behalf of the kernel.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic __sock_create function has a kern argument which allows the
security system to make decisions based on if a socket is being created by
the kernel or by userspace. This patch passes that flag to the
net_proto_family specific create function, so it can do the same thing.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct can_proto had a capability field which wasn't ever used. It is
dropped entirely.
struct inet_protosw had a capability field which can be more clearly
expressed in the code by just checking if sock->type = SOCK_RAW.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While hunting dev_put() for net-next-2.6, I found a device refcount
leak in ROSE, ioctl(SIOCADDRT) error path.
Fix is to not touch device refcount, as we hold RTNL
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge code assumes ethernet addressing, so be more strict in
the what is allowed. This showed up when GRE had a bug and was not
using correct address format.
Add some more comments for increased clarity.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to parse the option of a SYN packet that we have
no route entry for should just use global wide defaults
for route entry options.
Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Tested-by: Valdis.Kletnieks@vt.edu
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling IPv4 specific inet_csk_route_req in tcp_check_req
is a bad idea and crashes machine on IPv6 connections, as reported
by Valdis Kletnieks
Also, all we are really interested in is the timestamp
option in the header, so calling tcp_parse_options()
with the "estab" set to false flag is an overkill as
it tries to parse half a dozen other TCP options.
We know whether timestamp should be enabled or not
using data from request_sock.
Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Tested-by: Valdis.Kletnieks@vt.edu
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed by Stephen Rothwell, commit c6d14c84 added a warning :
net/ipv4/devinet.c: In function 'inet_select_addr':
net/ipv4/devinet.c:902: warning: label 'out' defined but not used
delete unused 'out' label and do some cleanups as well
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal scan request mac80211 uses to
scan for IBSS networks was set up to contain
no channels at all because n_channels wasn't
set after setting up the channels array. Fix
this to properly scan for networks.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, in IBSS mode, a single creator would go into
a loop trying to merge/scan. This happens because the IBSS timer is
rearmed on finishing a scan and the subsequent
timer invocation requests another scan immediately.
This patch fixes this issue by checking if we have just completed
a scan run trying to merge with other IBSS networks.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we have a TODO item to make all station
management dependent on virtual interfaces, I
figured I'd start with pushing such a change
to drivers before more drivers start using the
ieee80211_find_sta() API with a hw pointer and
cause us grief later on.
For now continue exporting the old API in form
of ieee80211_find_sta_by_hw(), but discourage
its use strongly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 211a4d12abf86fe0df4cd68fc6327cbb58f56f81
Author: Johannes Berg <johannes@sipsolutions.net>
Date: Tue Oct 20 15:08:53 2009 +0900
cfg80211: sme: deauthenticate on assoc failure
accidentally introduced a dead variable, I had
changed the code to not need it while creating
the patch and it looks like I forgot to remove
the variable (and nobody else noticed either).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adds RCU management to the list of netdevices.
Convert some for_each_netdev() users to RCU version, if
it can avoid read_lock-ing dev_base_lock
Ie:
read_lock(&dev_base_loack);
for_each_netdev(net, dev)
some_action();
read_unlock(&dev_base_lock);
becomes :
rcu_read_lock();
for_each_netdev_rcu(net, dev)
some_action();
rcu_read_unlock();
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another rcu conversion to avoid one dev_hold()/dev_put() pair
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These checks don't make sense anymore since rtnl_notify() cannot fail.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it is possible to request a scan on only
disabled channels, which could be problematic for
some drivers. Reject such scans, and also ignore
disabled channels that are given. This resuls in
the scan begin/end event only including channels
that are actually used.
This makes the mac80211 check for disabled channels
superfluous. At the same time, remove the no-IBSS
check from mac80211 -- nothing says that we should
not find any networks on channels that cannot be
used for an IBSS, even when operating in IBSS mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Neither of these commands should clear the current configuration value
if they return error. Furthermore, cfg80211_set_cipher_group() should
be able to handle IW_AUTH_CIPHER_NONE without reporting error.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since sometimes mac80211 queues up a scan request
to only act on it later, it must be allowed to
(internally) cancel a not-yet-running scan, e.g.
when the interface is taken down. This condition
was missing since we always checked only the
local->scanning variable which isn't yet set in
that situation.
Reported-by: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The multi-line code in this macro wasn't wrapped
in do {} while (0) so we cannot use it in an if()
branch safely in the future -- fix that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some strange reason the netif_running() check
ended up after the actual type change instead of
before, potentially causing all kinds of problems
if the interface is up while changing the type;
one of the problems manifests itself as a warning:
WARNING: at net/mac80211/iface.c:651 ieee80211_teardown_sdata+0xda/0x1a0 [mac80211]()
Hardware name: Aspire one
Pid: 2596, comm: wpa_supplicant Tainted: G W 2.6.31-10-generic #32-Ubuntu
Call Trace:
[] warn_slowpath_common+0x6d/0xa0
[] warn_slowpath_null+0x15/0x20
[] ieee80211_teardown_sdata+0xda/0x1a0 [mac80211]
[] ieee80211_if_change_type+0x4a/0xc0 [mac80211]
[] ieee80211_change_iface+0x61/0xa0 [mac80211]
[] cfg80211_wext_siwmode+0xc7/0x120 [cfg80211]
[] ioctl_standard_call+0x58/0xf0
(http://www.kerneloops.org/searchweek.php?search=ieee80211_teardown_sdata)
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 211a4d12abf86fe0df4cd68fc6327cbb58f56f81
Author: Johannes Berg <johannes@sipsolutions.net>
Date: Tue Oct 20 15:08:53 2009 +0900
cfg80211: sme: deauthenticate on assoc failure
introduced a potential NULL pointer dereference that
some people have been hitting for some reason -- the
params.bssid pointer is not guaranteed to be non-NULL
for what seems to be a race between various ways of
reaching the same thing.
While I'm trying to analyse the problem more let's
first fix the crash. I think the real fix may be to
avoid doing _anything_ if it ended up being NULL, but
right now I'm not sure yet.
I think
http://bugzilla.kernel.org/show_bug.cgi?id=14342
might also be this issue.
Reported-by: Parag Warudkar <parag.lkml@gmail.com>
Tested-by: Parag Warudkar <parag.lkml@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avoids touching device refcount in datagram_send_ctl(), thanks to RCU
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoids touching device refcount in inet6_bind(), thanks to RCU
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using dev_get_by_index_rcu() in ip6_tnl_rcv_ctl() & ip6_tnl_xmit_ctl()
avoids touching device refcount.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- packet_sendmsg_spkt() can use dev_get_by_name_rcu() to avoid touching device refcount.
- packet_getname_spkt() & packet_getname() can use dev_get_by_index_rcu() to
avoid touching device refcount too.
tpacket_snd() & packet_snd() can not use RCU yet because they can sleep when
allocating skb.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All ioctls() implemented by dev_ifsioc_locked() :
SIOCGIFFLAGS, SIOCGIFMETRIC, SIOCGIFMTU, SIOCGIFHWADDR,
SIOCGIFSLAVE, SIOCGIFMAP, SIOCGIFINDEX & SIOCGIFTXQLEN
can use RCU lock instead of dev_base_lock rwlock
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can avoid touching device refcount in icmp_send(),
using dev_get_by_index_rcu()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_get_by_index_rcu() instead of __dev_get_by_index() and
dev_base_lock rwlock
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I tested the recent unregister many changes and got a weird,
nasty and seemingly unrelasted kernel oops. Changing
unregister_netdevice_queue to use list_move_tail fixes
the problem for me.
ip link add type veth
rmmod veth
ls /sys/class/net/
showed one of the veth devices still present.
A subsequent ip link oopsed the box.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some workloads hit dev_base_lock rwlock pretty hard.
We can use RCU lookups to avoid touching this rwlock
(and avoid touching netdevice refcount)
netdevices are already freed after a RCU grace period, so this patch
adds no penalty at device dismantle time.
However, it adds a synchronize_rcu() call in dev_change_name()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move receive processing from event handler to a tasklet.
This should help prevent hangcheck timer from going off
when RDS is under heavy load.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was discovered by HP's Pradeep and fixed in OFED
1.3, but not fixed in later versions, since the fix's implementation
was not immediately applyable to the later code. This patch should
do the trick for 1.4+ codebases.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove explicit destruction of passive connection when destroying
active end of the connection. The passive end is also on the
device's connection list, and will thus be cleaned up properly.
Panic was caused by trying to clean it up twice.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"At rds_ib_recv_refill_one(), it first executes atomic_read(&rds_ib_allocation)
for if-condition checking,
and then executes atomic_inc(&rds_ib_allocation) if the condition was
not satisfied.
However, if any other code which updates rds_ib_allocation executes
between these two atomic operation executions,
it seems that it may result race condition. (especially when
rds_ib_allocation + 1 == rds_ib_sysctl_max_recv_allocation)"
This patch fixes this by using atomic_inc_unless to eliminate the
possibility of allocating more than rds_ib_sysctl_max_recv_allocation
and then decrementing the count if the allocation fails. It also
makes an identical change to the iwarp transport.
Reported-by: Shin Hong <hongshin@gmail.com>
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDS currently supports a GET_MR sockopt to establish a
memory region (MR) for a chunk of memory. However, the fastreg
method ties a MR to a particular destination. The GET_MR_FOR_DEST
sockopt allows the remote machine to be specified, and thus
support for fastreg (aka FRWRs).
Note that this patch does *not* do all of this - it simply
implements the new sockopt in terms of the old one, so applications
can begin to use the new sockopt in preparation for cutover to
FRWRs.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not right to do something here when returning an
error, and hostapd should never have relied on it as
it only fixes up a small part of the problem anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>