Until now the GPMI driver had its own timings logic while the core
already handles that and request the NAND controller drivers to support
the ->setup_data_interface() hook. Implement that hook by reusing the
already existing function. No real glue is necessary between core timing
delays and GPMI registers because the driver already translates the
ONFI timing modes into register values.
Make use of the core's tREA, tRLOH and tRHOH values that allow computing
more precise timings for mode [0-3] and get significantly better values
(+20% with an i.MX6 Sabre Auto board). Otherwise use the existing logic.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
Now that there is a small nand_parameters structure that hold all needed
ONFI parameters, remove the ONFI page from the nand_chip structure by
just allocating it during the identification phase and removing it right
after.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
Now that there is a small nand_parameters structure that can held
generic parameters, remove the JEDEC page from the nand_chip structure
by just allocating it during the identification phase and removing it
right after.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The MX30LF2G18AC chip declares in its parameter page supporting
SET/GET_FEATURES but when it comes to timings, experience shows that it
is not the case.
Unflag this feature for this particular chip in the nand_parameters
structure to avoid unnecessary errors and downturns.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
If SET/GET_FEATURES is available (from the parameter page), use a
bitmap to declare what feature is actually supported.
Initialize the bitmap in the core to support timing changes (only
feature used by the core), also add support for Micron specific features
used in Micron initialization code (in the init routine).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
ONFI-related parameters that will be used outside from the
identification function are stored in a separate onfi_parameters
structure embedded in nand_parameters, this small structure that
already hold generic parameters.
For now, the onfi_parameters structure is allocated statically. However,
after some deep rework in the NAND framework, it will be possible to do
dynamic allocations from the NAND identification phase, and this
strcuture will then be dynamically allocated when needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
To prepare to the removal of such huge structure, a small NAND parameter
structure is allocated statically and contains only very few members
that are generic to all chips and actually used elsewhere in the code.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
After a nand_reset_data_interface(), both the NAND chip and the NAND
controller use timing mode 0. The previously defined data interface for
this chip has been saved and is supposed to be restored after that.
However, if the saved data interface also refers to timing mode 0, there
is no need to re-apply them again.
Also, as nand_setup_data_interface() uses ->set/get_features(), it could
lead to issues when doing the reset at probe time as the parameter page
is not available yet to know if these functions are supported or not.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Choosing ONFI timings when ->set/get_features() calls are supported
by the NAND chip is a matter of reading the chip's ONFI parameter page
and telling the chip the chosen mode (between all of the supported ones)
with ->set_feature().
Add a check on whether the chip "acked" the timing mode or not.
This can be a problem for NAND chips that do not follow entirely the
ONFI specification. These chips actually support other modes than
"mode 0", but either:
1/ do not update the timing mode register once a timing mode has been
selected.
or
2/ do not support the TIMING_MODE featured and thus do not require users
to change the timing mode at all.
These issues will be addressed in another patch that will add the
feature to overwrite NAND chips features within the parameter page, from
the NAND chip driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
After a ->set_features(TIMINGS), the chip is supposed to be working at a
new speed. In order for all the transactions to be perperly handled, the
NAND controller should also be configured to this same speed. Calling
->setup_data_interface() is not enough and the chip should be
de-asserted/re-asserted through calls to ->select_chip().
Prepare the next change in nand_setup_data_interface() where timings
will be checked after being applied. Because assertions of the CS pin
will be needed from within this function, move the calls to
->select_chip() inside nand_setup_data_interface() for later
consistency.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
All the calls to the chip's hooks ->get/set_features() go through
the core's wrappers nand_get/set_features() that already do the
necessary checks about feature support. Remove these
checks from the mxc's functions.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Usually, the source of the error when setting/getting features does not
matter (if the controller does not support sending the command or if
the chip does not support the operation).
When it comes to timings, if the controller fails it is an error while
if the chip does not support the operation, it can be silently supposed
that it already works with the maximum supported timings.
Introduce some logic in nand_setup_data_interface() to handle that
difference.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Prepare the fact that some features managed by GET/SET_FEATURES could be
overloaded by vendor code. To handle this logic, use new wrappers
instead of directly call the ->get/set_features() hooks.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
SET/GET FEATURES are flagged ONFI-compliant because of their name. This
is not accurate as non-ONFI NAND chips support it and use it.
Rename the hooks and helpers to remove the "onfi" prefix.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Prepare future work on the ->onfi_get/set_features() hooks by renaming
the core's implementation as 'default' ones.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Files have been moved in the NAND subsystem to reflect the different
flavors of NAND devices.
Raw/Parallel NAND devices have been moved to a "raw" subdirectory to
make the difference with OneNAND and SPI NAND for instance. So adjust
the Kconfig entry to clarify things.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Section was not properly computed. The value of OOB region definition is
always ECC section 0 information in the OOB area, but we want to get all
the ECC bytes information, so we should call
mtd_ooblayout_ecc(mtd, section++, &oobregion) until it returns -ERANGE.
Fixes: c2b78452a9 ("mtd: use mtd_ooblayout_xxx() helpers where appropriate")
Cc: <stable@vger.kernel.org>
Signed-off-by: OuYang ZhiZhong <ouyzz@yealink.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The blackfin architecture is getting removed, so this driver has
become obsolete.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
With the move to ->exec_op() the driver should now support ONFI
SET/GET_FEATURES commands.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Now that the driver is using ->exec_op(), remove the old
hooks.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This reworks the driver to make use of ->exec_op() callback. The
command sequencer of the VF610 NFC aligns well with the new ops
interface.
The operations are translated to a NFC command code while filling
the necessary registers. Instead of using the special status and
read ID command codes (which require to read status/ID from
special registers instead of the regular data area) the driver
now now uses the main data buffer for all commands. This
simplifies the driver as no special casing is needed.
For control data (status byte, id bytes and parameter page) the
driver needs to reverse byte order for little endian CPUs since
the controller seems to store the bytes in big endian order in
the data buffer.
The current state seems to pass MTD tests on a Colibri VF61.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
->fail_addr and ->addr can be updated no matter the result of
parent->_erase(), we just need to remove the code doing the same thing
in mtd_erase_callback() to avoid adjusting those fields twice.
Note that this can be done because all MTD users have been converted to
not pass an erase_info->callback() and are thus only taking the
->addr_fail and ->addr fields into account after part_erase() has
returned.
While we're at it, get rid of the erase_info->mtd field which was only
needed to let mtd_erase_callback() get the partition device back.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
None of the mtd->_erase() implementations work in an asynchronous manner,
so let's simplify MTD users that call mtd_erase(). All they need to do
is check the value returned by mtd_erase() and assume that != 0 means
failure.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
mtd_erase() can return an error before ->fail_addr is initialized to
MTD_FAIL_ADDR_UNKNOWN. Move this initialization at the very beginning
of the function.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Use %*ph format to print small buffer as hex string.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Antonio Cardace <anto.cardace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Pointer bdev is being initialized however this value is never
read as bdev is assigned an updated value from the returned
call to blkdev_get_by_path. Remove the redundant assignment.
Cleans up clang warning:
drivers/mtd/devices/block2mtd.c:228:23: warning: Value stored to
'bdev' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This file can not be built independently any more. We would have to
bring in more to resolve mtd_to_nand(mtd)->ecc.size, for example.
It is difficult to notice a breakage since nobody compiles this mode.
It is not worth fixing or maintaining in my opinion. Remove.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Using pr_<loglevel>() is more concise than printk(KERN_<LOGLEVEL>).
Replace printks having a log level with the appropriate pr_*() macros.
Define pr_fmt() and remove other additional macros from the replaced
printks.
Signed-off-by: Shreeya Patel <shreeya.patel23498@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Move onenand code base to the drivers/mtd/nand directory in the hope
that someday someone will patch it to use the generic NAND helpers.
If it never happens, at least we'll have all NAND related support in a
single directory and not spread over the drivers/mtd/ directory.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Some files add a comment giving the path of the file inside the Linux
tree, which is pretty useless since the reader had to find the file to
open it.
Getting rid of these comments will also allow us to easily move these
files around when needed.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
- minor changes for property API
- clock API fix for ULPI driver warning
It exceptionally contains a merge from the mtd tree from Boris
to prevent any merge conflicts in the PXA tree.
-----BEGIN PGP SIGNATURE-----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=/vgG
-----END PGP SIGNATURE-----
Merge tag 'pxa-for-4.17' of https://github.com/rjarzmik/linux into next/soc
Pull "This is the pxa changes for v4.17 cycle" from Robert Jarzmik:
- minor changes for property API
- clock API fix for ULPI driver warning
It exceptionally contains a merge from the mtd tree from Boris
to prevent any merge conflicts in the PXA tree.
* tag 'pxa-for-4.17' of https://github.com/rjarzmik/linux:
ARM: pxa/raumfeld: use PROPERTY_ENTRY_U32() directly
ARM: pxa: ulpi: fix ulpi timeout and slowpath warn
ARM: pxa: cm-x300: remove inline directive
ARM: pxa: fix static checker warning in pxa3xx-ulpi
MAINTAINERS: remove entry for deleted pxa3xx_nand driver
arm: dts: pxa: use reworked NAND controller driver
dt-bindings: mtd: remove pxa3xx NAND controller documentation
mtd: nand: remove useless fields from pxa3xx NAND platform data
mtd: nand: remove deprecated pxa3xx_nand driver
mtd: nand: use Marvell reworked NAND controller driver with all platforms
This patch has been generated as follows:
for verb in set_unlocked clear_unlocked set clear; do
replace-in-files queue_flag_${verb} blk_queue_flag_${verb%_unlocked} \
$(git grep -lw queue_flag_${verb} drivers block/bsg*)
done
Except for protecting all queue flag changes with the queue lock
this patch does not change any functionality.
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The "enable arbiter" bit is available only for pxa3xx based platforms
but it was experimentally shown that even if this bit is reserved,
some Marvell platforms (64-bit) actually need it to be set. The driver
always set this bit regardless of this property, which is harmless.
Then this property is not needed.
The "num_cs" field is always 1 and for a good reason, the old driver
(pxa3xx_nand.c) could only handle one. The new driver that replaces it
(marvell_nand.c) can handle more, but better use device tree for such
description. As there is only one available chip select, there is no
need for an array of partitions neither an array of partition numbers.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
All board files and defconfig files have been moved to use the new
marvell_nand driver instead of pxa3xx_nand, so we can safely remove this
file now. People should use the new driver which is supposed to behave
exactly like the old one.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Remove the deprecated ->cmd_ctrl() implementation to use ->exec_op() in
the fsmc_nand driver.
Implement the ->select_chip() hook to avoid having to support the hack
from the core that send a NAND_CMD_NONE with NAND_NCE to signal a
deassertion of nCE.
Also get rid of the last references to ->IO_ADDR_[R|W] that are not used
anymore.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Remove the use of IO_ADDR_[R|W] in the fsmc_nand driver. Instead, use a
pointer to the control registers to avoid doing several arithmetic
operations (including a multiplication) each time a control register is
read or written.
All references to IO_ADDR_[R|W] are not entirely removed from the driver
as, at this time, these values are needed by the NAND core in the
default ->read/write_byte/word() hooks. These references will be
entirely removed when switching to ->exec_op(), that does not make use
of these hooks anymore.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add an intermediate layer to abstract NAND device interface so that
some logic can be shared between SPI NANDs, parallel/raw NANDs,
OneNANDs, ...
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
As part of the process of sharing more code between different NAND
based devices, we need to move all raw NAND related code to the raw/
subdirectory.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Some drivers have been derived from others which have then been removed
from the source tree. When this is the case, add mention the copyright
of the source file(s) they've been derived from.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
A lot of NAND drivers have been derived from other old NAND drivers
which have since then been removed from the Linux tree. When this is
the case, specify when the file the header is referring to has been
removed so that people can find the original implementation more
easily.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Last known location of toto.c was drivers/mtd/nand/toto.c. Fix the
path so that one can use git log to find when the driver was deleted
and possibly checkout the source code.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Some NAND drivers are derived from other NAND drivers and state it in
their license header. Using full path to point to other driver files
sitting in the same directory is not such a good idea, since the NAND
drivers might be moved to a different directory at some point, and we
don't to patch all license/copyright headers everytime this happen.
The only exception where we keep full path is when the referred source
files no longer exist in the tree.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Some files add a comment giving the path of the file inside the Linux
tree, which is pretty useless since the reader had to find the file to
open it.
Getting rid of these comments will also allow us to easily move these
files around when needed.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This patch enables support to read the ECC strength and size from the
NAND flash using Toshiba Memory SLC NAND extended-ID. This patch is
based on the information of the 6th ID byte of the Toshiba Memory SLC
NAND.
Signed-off-by: KOBAYASHI Yoshitake <yoshitake.kobayashi@toshiba.co.jp>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
vf610_nfc_probe() misses error handling of mtd_device_register().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Use clearer error labels as Boris Brezillon suggested.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Calling of_node_put() in vf610_nfc_probe() is wrong because nothing in
this code retains a reference to the DT node.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The function count_written_bits has been replaced by the generic
nand_check_erased_ecc_chunk() function with commit 48c25cf441
("mtd: nand: vf610_nfc: use nand_check_erased_ecc_chunk() helper").
Remove the unused function.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
First generation of Marvell NAND flash controllers (eg. embedded in PXA
boards) did not make use of the NAND core hook ->setup_data_interface()
to setup controller timings. Add support for it.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Since we now have our own read_page/write_page functions
mxc_nand_command() will no longer be called with NAND_CMD_READ0,
NAND_CMD_READOOB, NAND_CMD_SEQIN and NAND_CMD_PAGEPROG. Remove
the code handling these commands.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Since we have our own read_page/write_page functions correct_data and
calculate are no longer needed. Remove them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Now that we have our own read_page function add a write_page function
for consistency aswell. This can be a lot easier than the generic
function since we do not have to iterate over subpages but can write
the whole page at once. Also add write_page_raw and write_oob for
proper raw and oob write support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The v1 controller code has several flaws:
- We do not forward the number of corrected bitflips to the upper layers
- For 2k page NAND chips only the status results from the fourth subpage
read are evaluated, so ECC failures in the other subpages remain
uncovered
- When there are uncorrectable errors we have to increase the statistics
counter, but still have to return successfully. Currently we return
an error
This patch fixes this by introducing a v1 specific read_page function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Currently nand_read_page_hwecc() from nand_base calls
mxc_nand_correct_data_v2_v3() for each subpage, but in this function we
return the corrected/failed results for the whole page instead
of a single subpage. On a 2k page size Nand this leads to results which
are 4 times too high.
The whole ecc.calculate/ecc.correct mechanism used by
nand_read_page_hwecc() is not suitable for devices which correct the
data in hardware, so fix this by using a driver specific read_page
function which does the right thing. Also add read_page_raw and read_oob
For proper raw and oob read support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
With following patches we will have to copy the spare data to/from
other buffers, so add the buffer as argument to copy_spare().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
For proper raw read/write support need to be able to control the
hardware ECC engine. Add a function to enable/disable it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
We'll call copy_spare() and mxc_do_addr_cycle() from another place
during the next patches, so move functions up to avoid forward
declarations.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This simplifies code a bit by:
1) Avoiding an extra (tiny) function
2) Checking for amount of parsed (found) partitions just once
3) Avoiding clearing/filling struct mtd_partitions manually
With this commit proper functions are called directly from the
mtd_device_parse_register(). It doesn't need to use minor tricks like
memsetting struct to 0 to trigger an expected
mtd_add_device_partitions() behavior.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This change is a small cleanup of mtd_device_parse_register(). When
using MTD_PARTITIONED_MASTER it makes sure a master MTD is registered
before dealing with partitions. The advantage of this is not mixing
code handling master MTD with code handling partitions.
This commit doesn't change any behavior except from a slightly different
failure code path. The new code may need to call del_mtd_device when
something goes wrong.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Some devices do not implement ->_erase() or have an invalid ->erasesize
value. In this case, mtd_erase() should return -ENOTSUPP.
Note that the test is not done on the MTD_NO_ERASE flag because this
flag means 'erasing a block before writing to it is unnecessary',
not 'the erase operation is not supported'. Actually, some drivers are
setting the MTD_NO_ERASE flag but still implementing the ->_erase()
hook and setting a valid ->erasesize value.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
With commit 3cf32d1802 ("mtd: nand: vf610: switch to
mtd_ooblayout_ops") the driver started to use the NAND cores
default large page ooblayout. However, shortly after commit
6a623e0769 ("mtd: nand: add ooblayout for old hamming layout")
changed the default layout to the old hamming layout, which is
not what vf610_nfc is using. Specify the default large page
layout explicitly.
Fixes: 6a623e0769 ("mtd: nand: add ooblayout for old hamming layout")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This pull requests contains a consolidation of the generic no-IOMMU code,
a well as the glue code for swiotlb. All the code is based on the x86
implementation with hooks to allow all architectures that aren't cache
coherent to use it. The x86 conversion itself has been deferred because
the x86 maintainers were a little busy in the last months.
-----BEGIN PGP SIGNATURE-----
iQI/BAABCAApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAlpxcVoLHGhjaEBsc3Qu
ZGUACgkQD55TZVIEUYN/Lw/+Je9teM4NPQ8lU/ncbJN/bUzCFGJ6dFt2eVX/6xs3
sfl8vBdeHt6CBM02rRNecEr31z3+orjQes5JnlEJFYeG3jumV0zCPw/zbxqjzbJ1
3n6cckLxbxzy8Ca1G/BVjHLAUX5eWp1ujn/Q4d03VKVQZhJvFYlqDbP3TrNVx7xn
k86u37p/o+ngjwX66UdZ3C4iIBF8zqy6n2kkpv4HUQtHHzPwEvliN39eNilovb56
iGOzjDX1UWHAu4xCTVnPHSG4fA4XU41NWzIN3DIVPE25lYSISSl9TFAdR8GeZA0G
0Yj6sW53pRSoUwco1ocoS44/FgrPOB5/vHIL06pABvicXBiomje1QylqcK7zAczk
esjkfPEZrmZuu99GtqFyDNKEvKKdy+aBGaTZ3y+NxsuBs+0xS2Owz1IE4Tk28xaw
xh7zn+CVdk2fJh6ZIdw5Eu9b9VN08UriqDmDzO/ylDlcNGcDi7wcxiSTEkHJ1ON/
g9nletV6f3egL0wljDcOnhCJCHTvmWEeq3z8lE55QzPzSH0hHpnGQ2WD0tKrroxz
kjOZp0TdXa4F5iysOHe2xl2sftOH0zIkBQJ+oBcK12mTaLu21+yeuCggQXJ/CBdk
1Ol7l9g9T0TDuZPfiTHt5+6jmECQs92LElWA8x7uF7Fpix3BpnafWaaSMSsosF3F
D1Y=
=Nrl9
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.16' of git://git.infradead.org/users/hch/dma-mapping
Pull dma mapping updates from Christoph Hellwig:
"Except for a runtime warning fix from Christian this is all about
consolidation of the generic no-IOMMU code, a well as the glue code
for swiotlb.
All the code is based on the x86 implementation with hooks to allow
all architectures that aren't cache coherent to use it.
The x86 conversion itself has been deferred because the x86
maintainers were a little busy in the last months"
* tag 'dma-mapping-4.16' of git://git.infradead.org/users/hch/dma-mapping: (57 commits)
MAINTAINERS: add the iommu list for swiotlb and xen-swiotlb
arm64: use swiotlb_alloc and swiotlb_free
arm64: replace ZONE_DMA with ZONE_DMA32
mips: use swiotlb_{alloc,free}
mips/netlogic: remove swiotlb support
tile: use generic swiotlb_ops
tile: replace ZONE_DMA with ZONE_DMA32
unicore32: use generic swiotlb_ops
ia64: remove an ifdef around the content of pci-dma.c
ia64: clean up swiotlb support
ia64: use generic swiotlb_ops
ia64: replace ZONE_DMA with ZONE_DMA32
swiotlb: remove various exports
swiotlb: refactor coherent buffer allocation
swiotlb: refactor coherent buffer freeing
swiotlb: wire up ->dma_supported in swiotlb_dma_ops
swiotlb: add common swiotlb_map_ops
swiotlb: rename swiotlb_free to swiotlb_exit
x86: rename swiotlb_dma_ops
powerpc: rename swiotlb_dma_ops
...
- Usage of new fscrypt APIs
- A fix for a Fastmap issue
- Other minor bug fixes
-----BEGIN PGP SIGNATURE-----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=+cCd
-----END PGP SIGNATURE-----
Merge tag 'upstream-4.16-rc1' of git://git.infradead.org/linux-ubifs
Pull UBI/UBIFS updates from Richard Weinberger:
- use the new fscrypt APIs
- a fix for a Fastmap issue
- other minor bug fixes
* tag 'upstream-4.16-rc1' of git://git.infradead.org/linux-ubifs:
ubi: block: Fix locking for idr_alloc/idr_remove
mtd: ubi: wl: Fix error return code in ubi_wl_init()
ubi: Fix copy/paste error in function documentation
ubi: Fastmap: Fix typo
ubifs: remove error message in ubifs_xattr_get
ubi: fastmap: Erase outdated anchor PEBs during attach
ubifs: switch to fscrypt_prepare_setattr()
ubifs: switch to fscrypt_prepare_lookup()
ubifs: switch to fscrypt_prepare_rename()
ubifs: switch to fscrypt_prepare_link()
ubifs: switch to fscrypt_file_open()
ubi: fastmap: Clean up the initialization of pointer p
ubi: fastmap: Use kmem_cache_free to deallocate memory
ubi: Fix race condition between ubi volume creation and udev
mtd: ubi: Use 'max_bad_blocks' to compute bad_peb_limit if available
ubifs: Fix uninitialized variable in search_dh_cookie()
Core changes:
* Rework core functions to avoid duplicating generic checks in
NAND/OneNAND sub-layers
* Update the MAINTAINERS entry to reflect the fact that MTD
maintainers now use a single git tree
Driver changes:
* CFI: use macros instead of inline functions to limit stack
usage and make KASAN happy
NAND changes:
Core changes:
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
* Introduce the ->exec_op() infrastructure
* Rework NAND buffers handling
* Fix ECC requirements for K9F4G08U0D
* Fix nand_do_read_oob() to return the number of bitflips
* Mark K9F1G08U0E as not supporting subpage writes
Driver changes:
* MTK: Rework the driver to support new IP versions
* OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
DT support
* Marvell: Add a new driver to replace the pxa3xx one
SPI NOR changes:
Core changes:
* Add support to new ISSI and Cypress/Spansion memory parts.
* Fix support of Micron memories by checking error bits in the FSR.
* Fix update of block-protection bits by reading back the SR.
* Restore the internal state of the SPI flash memory when removing the
device.
Driver changes:
* Maintenance for Freescale, Intel and Metiatek drivers.
* Add support of the direct access mode for the Cadence QSPI controller.
-----BEGIN PGP SIGNATURE-----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=Mxo2
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"MTD core changes:
- Rework core functions to avoid duplicating generic checks in
NAND/OneNAND sub-layers
- Update the MAINTAINERS entry to reflect the fact that MTD
maintainers now use a single git tree
MTD driver changes:
- CFI: use macros instead of inline functions to limit stack usage
and make KASAN happy
NAND core changes:
- Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
- Introduce the ->exec_op() infrastructure
- Rework NAND buffers handling
- Fix ECC requirements for K9F4G08U0D
- Fix nand_do_read_oob() to return the number of bitflips
- Mark K9F1G08U0E as not supporting subpage writes
NAND driver changes:
- MTK: Rework the driver to support new IP versions
- OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and
fix DT support
- Marvell: Add a new driver to replace the pxa3xx one
SPI NOR core changes:
- Add support to new ISSI and Cypress/Spansion memory parts.
- Fix support of Micron memories by checking error bits in the FSR.
- Fix update of block-protection bits by reading back the SR.
- Restore the internal state of the SPI flash memory when removing
the device.
SPI NOR driver changes:
- Maintenance for Freescale, Intel and Metiatek drivers.
- Add support of the direct access mode for the Cadence QSPI
controller"
* tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd: (93 commits)
mtd: nand: sunxi: Fix ECC strength choice
mtd: nand: gpmi: Fix subpage reads
mtd: nand: Fix build issues due to an anonymous union
mtd: nand: marvell: Fix missing memory allocation modifier
mtd: nand: marvell: remove redundant variable 'oob_len'
mtd: nand: marvell: fix spelling mistake: "suceed"-> "succeed"
mtd: onenand: omap2: Remove redundant dev_err call in omap2_onenand_probe()
mtd: Remove duplicate checks on mtd_oob_ops parameter
mtd: Fallback to ->_read/write_oob() when ->_read/write() is missing
mtd: mtdpart: Make ECC stat handling consistent
mtd: onenand: omap2: print resource using %pR format string
mtd: mtk-nor: modify functions' name more generally
mtd: onenand: samsung: remove incorrect __iomem annotation
MAINTAINERS: Add entry for Marvell NAND controller driver
ARM: OMAP2+: Remove gpmc-onenand
mtd: onenand: omap2: Configure driver from DT
mtd: onenand: omap2: Decouple DMA enabling from INT pin availability
mtd: onenand: omap2: Do not make delay for GPIO OMAP3 specific
mtd: onenand: omap2: Convert to use dmaengine for memcpy
mtd: onenand: omap2: Unify OMAP2 and OMAP3 DMA implementation
...
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
* Introduce the ->exec_op() infrastructure
* Rework NAND buffers handling
* Fix ECC requirements for K9F4G08U0D
* Fix nand_do_read_oob() to return the number of bitflips
* Mark K9F1G08U0E as not supporting subpage writes
Driver changes:
* MTK: Rework the driver to support new IP versions
* OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
DT support
* Marvell: Add a new driver to replace the pxa3xx one
-----BEGIN PGP SIGNATURE-----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=TXIU
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.16' of git://git.infradead.org/linux-mtd into mtd/next
Pull NAND changes from Boris Brezillon:
"
Core changes:
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
* Introduce the ->exec_op() infrastructure
* Rework NAND buffers handling
* Fix ECC requirements for K9F4G08U0D
* Fix nand_do_read_oob() to return the number of bitflips
* Mark K9F1G08U0E as not supporting subpage writes
Driver changes:
* MTK: Rework the driver to support new IP versions
* OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
DT support
* Marvell: Add a new driver to replace the pxa3xx one
"
Core changes:
* Add support to new ISSI and Cypress/Spansion memory parts.
* Fix support of Micron memories by checking error bits in the FSR.
* Fix update of block-protection bits by reading back the SR.
* Restore the internal state of the SPI flash memory when removing the
device.
Driver changes:
* Maintenance for Freescale, Intel and Metiatek drivers.
* Add support of the direct access mode for the Cadence QSPI controller.
-----BEGIN PGP SIGNATURE-----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=3oDP
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.16' of git://git.infradead.org/linux-mtd into mtd/next
Pull spi-nor changes from Cyrille Pitchen:
"
This pull-request contains the following notable changes:
Core changes:
* Add support to new ISSI and Cypress/Spansion memory parts.
* Fix support of Micron memories by checking error bits in the FSR.
* Fix update of block-protection bits by reading back the SR.
* Restore the internal state of the SPI flash memory when removing the
device.
Driver changes:
* Maintenance for Freescale, Intel and Metiatek drivers.
* Add support of the direct access mode for the Cadence QSPI controller.
"
When the requested ECC strength does not exactly match the strengths
supported by the ECC engine, the driver is selecting the closest
strength meeting the 'selected_strength > requested_strength'
constraint. Fix the fact that, in this particular case, ecc->strength
value was not updated to match the 'selected_strength'.
For instance, one can encounter this issue when no ECC requirement is
filled in the device tree while the NAND chip minimum requirement is not
a strength/step_size combo natively supported by the ECC engine.
Fixes: 1fef62c142 ("mtd: nand: add sunxi NAND flash controller support")
Cc: <stable@vger.kernel.org>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Commit 25f815f66a ("mtd: nand: force drivers to explicitly send
READ/PROG commands") added a call to nand_read_page_op() in
gpmi_ecc_read_page(), which means this function now sends a READ0
command and place the data pointer at the beginning of the page. This
logic is breaking gpmi_ecc_read_subpage() which was calling
gpmi_ecc_read_page() and expected it to only retrieve the data without
sending the READ0 command.
Create a gpmi_ecc_read_page_data() helper which only does the data
retrieval and ECC correction steps and implement gpmi_ecc_read_page()
as a wrapper that calls nand_read_page_op()+gpmi_ecc_read_page_data().
This way, gpmi_ecc_read_subpage() can call gpmi_ecc_read_page_data()
which restores the logic we had before commit 25f815f66a ("mtd: nand:
force drivers to explicitly send READ/PROG commands").
Fixes: 25f815f66a ("mtd: nand: force drivers to explicitly send READ/PROG commands")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Han Xu <han.xu@nxp.com>
GCC-4.4.4 raises errors when assigning a parameter in an anonymous
union, leading to this kind of failure:
drivers/mtd/nand/marvell_nand.c:1936:
warning: missing braces around initializer
warning: (near initialization for '(anonymous)[1].<anonymous>')
error: unknown field 'data' specified in initializer
error: unknown field 'addr' specified in initializer
Work around the situation by naming these unions.
Fixes: 8878b126df ("mtd: nand: add ->exec_op() implementation")
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Tested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The function marvell_nfc_init_dma() allocates a DMA buffer without the
GFP_KERNEL modifier, that triggers this warning:
"marvell_nfc_init_dma() error: no modifiers for allocation."
Fix this by using (GFP_KERNEL | GFP_DMA) instead of only GFP_DMA as the
probe happens in non-interrupt context.
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Variable oob_len is assigned and never read, hence it is redundant and
can be removed.
Cleans up clang warnings:
drivers/mtd/nand/marvell_nand.c:1356:6: warning: Value stored to 'oob_len'
during its initialization is never read
drivers/mtd/nand/marvell_nand.c:1369:4: warning: Value stored to 'oob_len'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Trivial fix to spelling mistakes in dev_err error message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This fixes a race with idr_alloc where gd->first_minor can be set to the
same value for two simultaneous calls to ubiblock_create. Each instance
calls device_add_disk with the same first_minor. device_add_disk calls
bdi_register_owner which generates several warnings.
WARNING: CPU: 1 PID: 179 at kernel-source/fs/sysfs/dir.c:31
sysfs_warn_dup+0x68/0x88
sysfs: cannot create duplicate filename '/devices/virtual/bdi/252:2'
WARNING: CPU: 1 PID: 179 at kernel-source/lib/kobject.c:240
kobject_add_internal+0x1ec/0x2f8
kobject_add_internal failed for 252:2 with -EEXIST, don't try to
register things with the same name in the same directory
WARNING: CPU: 1 PID: 179 at kernel-source/fs/sysfs/dir.c:31
sysfs_warn_dup+0x68/0x88
sysfs: cannot create duplicate filename '/dev/block/252:2'
However, device_add_disk does not error out when bdi_register_owner
returns an error. Control continues until reaching blk_register_queue.
It then BUGs.
kernel BUG at kernel-source/fs/sysfs/group.c:113!
[<c01e26cc>] (internal_create_group) from [<c01e2950>]
(sysfs_create_group+0x20/0x24)
[<c01e2950>] (sysfs_create_group) from [<c00e3d38>]
(blk_trace_init_sysfs+0x18/0x20)
[<c00e3d38>] (blk_trace_init_sysfs) from [<c02bdfbc>]
(blk_register_queue+0xd8/0x154)
[<c02bdfbc>] (blk_register_queue) from [<c02cec84>]
(device_add_disk+0x194/0x44c)
[<c02cec84>] (device_add_disk) from [<c0436ec8>]
(ubiblock_create+0x284/0x2e0)
[<c0436ec8>] (ubiblock_create) from [<c0427bb8>]
(vol_cdev_ioctl+0x450/0x554)
[<c0427bb8>] (vol_cdev_ioctl) from [<c0189110>] (vfs_ioctl+0x30/0x44)
[<c0189110>] (vfs_ioctl) from [<c01892e0>] (do_vfs_ioctl+0xa0/0x790)
[<c01892e0>] (do_vfs_ioctl) from [<c0189a14>] (SyS_ioctl+0x44/0x68)
[<c0189a14>] (SyS_ioctl) from [<c0010640>] (ret_fast_syscall+0x0/0x34)
Locking idr_alloc/idr_remove removes the race and keeps gd->first_minor
unique.
Fixes: 2bf50d42f3 ("UBI: block: Dynamically allocate minor numbers")
Cc: stable@vger.kernel.org
Signed-off-by: Bradley Bolen <bradleybolen@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Fix to return error code -ENOMEM from the kmem_cache_alloc() error
handling case instead of 0, as done elsewhere in this function.
Fixes: f78e5623f4 ("ubi: fastmap: Erase outdated anchor PEBs during
attach")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The function documentation of leb_write_trylock is copied from
leb_write_lock. Replace the function name with the correct one.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Fix misspelling of 'available' in function name.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
The fastmap update code might erase the current fastmap anchor PEB
in case it doesn't find any new free PEB. When a power cut happens
in this situation we must not have any outdated fastmap anchor PEB
on the device, because that would be used to attach during next
boot.
The easiest way to make that sure is to erase all outdated fastmap
anchor PEBs synchronously during attach.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Richard Weinberger <richard@nod.at>
Fixes: dbb7d2a88d ("UBI: Add fastmap core")
Cc: <stable@vger.kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
The pointer p is being initialized with one value and a few lines
later being set to a newer replacement value. Clean up the code by
using the latter assignment to p as the initial value. Cleans up
clang warning:
drivers/mtd/ubi/fastmap.c:217:19: warning: Value stored to 'p'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Memory allocated by kmem_cache_alloc() should not be deallocated with
kfree(). Use kmem_cache_free() instead.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Similar to commit 714fb87e8b ("ubi: Fix race condition between ubi
device creation and udev"), we should make the volume active before
registering it.
Signed-off-by: Clay McClure <clay@daemons.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
If the user has not set max_beb_per1024 using either the cmdline or
Kconfig options for doing so, use the MTD function 'max_bad_blocks' to
compute the UBI bad_peb_limit.
Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electron.com>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Richard Weinberger <richard@nod.at>
Some of the check done in custom ->_read/write_oob() implementation are
already done by the core (in mtd_check_oob_ops()).
Suggested-by: Peter Pan <peterpansjtu@gmail.com>
[Remove redundant checks done in mtdpart.c]
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Some MTD sublayers/drivers are implementing ->_read/write_oob() and
provide dummy wrappers for their ->_read/write() implementations.
Let the core handle this case instead of duplicating the logic.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
part_read() and part_read_oob() were counting ECC failures and
bitflips differently. Adjust part_read_oob() to mimic what is done in
part_read(). This is needed to use ->_read_oob() as a fallback when
when ->_read() is not implemented.
Note that bitflips and ECC failure accounting on MTD partitions is
broken by design, because nothing prevents concurrent accesses to the
underlying master MTD device between the moment we save the stats in a
local variable and the moment master->_read[_oob]() returns. It's not
something that can easily be fixed, so leave it like that for now.
Suggested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
The omap2 onenand driver is now available for compile-testing, which
uncovers a warning in configurations that have a 64-bit resource_size_t:
drivers/mtd/onenand/omap2.c: In function 'omap2_onenand_probe':
drivers/mtd/onenand/omap2.c:536:54: error: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'resource_size_t {aka long long unsigned int}' [-Werror=format=]
dev_err(dev, "Cannot reserve memory region at 0x%08x, size: 0x%x\n",
drivers/mtd/onenand/omap2.c:536:66: error: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t {aka long long unsigned int}' [-Werror=format=]
Changing the format string to the special %pR simplifies the code
and lets it do the right thing in that configuration, while avoiding
the warning.
Fixes: a758f50f10 ("mtd: onenand: omap2: Configure driver from DT")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Since more and more Mediatek's SoC can use this driver to
control spi-nor flash, functions' name with "mt8173_" is
no longer properly. Replacing "mt8173_" with "mtk_" will
be more accurate to describe these functions' usable scope.
Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
'page_buf' and 'oob_buf' are allocated with 'devm_kzalloc()' and should not
have __iomem decoration.
Remove these decorations and some useless casting.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Move away from platform data configuration and use pure DT approach.
Use generic probe function to deal with OneNAND node and remove now useless
gpmc_probe_onenand_child function. Import sync mode timing calculation
function from mach-omap2/gpmc-onenand.c
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
INT pin (gpio_irq) is not really needed for DMA but only for notification
when a command that needs wait has completed. DMA memcpy can be still used
even without gpio_irq available, so enable it unconditionally.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Second commit in driver history (782b7a367d81: "[MTD] [OneNAND] OMAP3:
add delay for GPIO") added quirk for waiting until GPIO line settle.
As DMA was disabled for OMAP2 boards, chances are this problem was
not OMAP3 specific and as it is just one register read, previous
test for SoC type is approximately as expensive as read itself.
Make delay unconditional, which allows removing SoC specific code
alltogether.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Do not use the legacy and deprecated omap-dma interface for setting up the
memcpy.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Since the very first commit (36cd4fb5d277: "[MTD] [OneNAND] Add
OMAP2 / OMAP3 OneNAND driver") DMA is disabled for OMAP2. Later
fixes thus went only into OMAP3 specific DMA functions which
turned out not to be so OMAP3 specific, so merge those two
implementations.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We have 4 functions containing almost identical DMA setup code. Create one
function which can set up the DMA for both read and write and use this in
place for the setup code in the driver.
The new function will use wait_for_completion_io_timeout() and it will
figure out the best data_type to be used for the transfer instead of
hardwiring 32 or 16 bit data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Use wait_for_completion_io_timeout, which has an impact on how the
task is accounted in scheduling stats.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
No platform data user setups partitioning information, so remove.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
No platform data user sets skip_initial_unlocking, so remove test
for this field.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
As no platform data user sets regulator_can_sleep, regulator code is
no-op and can be deleted.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Miquel Raynal
OuYang ZhiZhong
Arnd Bergmann
Stefan Agner
Boris Brezillon
Antonio Cardace
Colin Ian King
Masahiro Yamada
Shreeya Patel
Bart Van Assche
KOBAYASHI Yoshitake
Alexey Khoroshilov
Miquel Raynal
Sascha Hauer
Rafał Miłecki
Boris Brezillon
Geert Uytterhoeven
Linus Torvalds
Wei Yongjun
Bradley Bolen
Pan Bian
Clay McClure
Jeff Westfahl
Guochun Mao
Christophe JAILLET
Ladislav Michl
Peter Ujfalusi