Up till now we only needed to access the partition table in boot.c.
But to add support for reading the MAC address from the FUSE in
testmode, we will have to change the partition in testmode.c.
Thus, we move the partition table to io.c and export it via io.h. It
makes more sense to have it in the io part anyway.
Signed-off-by: Luciano Coelho <coelho@ti.com>
after re-factoring a bunch of symbols are only
used inside main.c which allows us to mark
them as static.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[forward-ported]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Move all common parts from sdio.c and spi.c to main.c, since they now
can be handled as part of the platform driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[forward-ported, cleaned-up and rephrased commit message]
[added a bunch of fixes and a new pdata element]
[moved some new code into main.c as well]
Signed-off-by: Luciano Coelho <coelho@ti.com>
The new fw doesn't support rx_filtering configuration (as a
stand-alone command. the rx filtering is done automatically
according to the active role).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
A recently added feature to the firmware enables the driver to retrieve
firmware logs via the host bus (SDIO or SPI).
There are two modes of operation:
1. On-demand: The FW collects its log in an internal ring buffer. This
buffer can later be read, for example, upon recovery.
2. Continuous: The FW pushes the FW logs as special packets in the RX
path.
Reading the internal ring buffer does not involve the FW. Thus, as long
as the HW is not in ELP, it should be possible to read the logs, even if
the FW crashes.
A sysfs binary file named "fwlog" was added to support this feature,
letting a monitor process read the FW messages. The log is transferred
from the FW only when available, so the reading process might block.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wl12xx device normally drops all frames coming from BSSID
it is not joined with.
This behavior is configured today by the wl12xx driver in response
to a handful of ieee80211_bss_change and ieee80211_conf_changed
notification flags, such as BSS_CHANGED_ASSOC, BSS_CHANGED_BSSID,
IEEE80211_CONF_CHANGE_IDLE, etc..
This breaks when we roam to a new BSSID, where authentication frames
are sent before any BSS_CHANGED/CONF_CHANGED flags are received.
When this happens the hardware silently drops the authentication
responses, and the roaming fails.
Ideally this aggressive filtering behavior of the device should be disabled
upon a notification from mac80211. Such notification will take place
after multi-channel support will be added: mac80211 will likely send a
remain-on-channel notification to drivers when entering sensitive
states (like authentication), otherwise the firmware might jump to
different channels (to serve a different role).
Until those notifications materialize, disable the hw BSSID filter
when authentication requests are sent, so roaming would work.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Support sending dummy packet to wl128x FW as results of
dummy packet event. That is part of dynamic TX mem blocks mechanism.
Only send dummy packet when not in AP mode.
[Even though the DUMMY_PACKET_EVENT_ID and the
STA_REMOVE_COMPLETE_EVENT_ID events are defined to the same value, we
need to treat them separately in the code. Keep the check and enable
STA_REMOVE_COMPLETE_EVENT_ID for AP mode and DUMMY_PACKET_EVENT_ID for
STA. Moved one warning to a cleaner place. Use WL1271_TID_MGMT for
dummy packets -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
New acx command that sets: Rx fifo enable reduced bus transactions
in RX path. Tx bus transactions padding to SDIO block size that
improve preference in Tx and essential for working with SDIO HS (48Mhz).
The max SDIO block size is 256 when working with Tx bus transactions
padding to SDIO block.
Add new ops to SDIO & SPI that handles the win size change in case of
transactions padding (relevant only for SDIO).
[Fix endianess issues; simplify sdio-specific block_size handling;
minor changes in comments; use "aligned_len" in one calculation
instead of "pad" to avoid confusion -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
To achieve maximal throughput, it is very important to react to
interrupts as soon as possible. Currently the interrupt handler wakes up
a worker for handling interrupts in process context. A cleaner and more
efficient design would be to request a threaded interrupt handler. This
handler's priority is very high, and can do blocking operations such as
SDIO/SPI transactions.
Some work can be deferred, mostly calls to mac80211 APIs
(ieee80211_rx_ni and ieee80211_tx_status). By deferring such work to a
different worker, we can keep the irq handler thread more I/O
responsive. In addition, on multi-core systems the two threads can be
scheduled on different cores, which will improve overall performance.
The use of WL1271_FLAG_IRQ_PENDING & WL1271_FLAG_IRQ_RUNNING was
changed. For simplicity, always query the FW for more pending
interrupts. Since there are relatively long bursts of interrupts, the
extra FW status read overhead is negligible. In addition, this enables
registering the IRQ handler with the ONESHOT option.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
All files name prefix removed due to the fact that wl12xx driver supports
wl1271 and wl1273.
Also the definition in Kconfig and header files changed respectively.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Luciano Coelho
Felipe Balbi
Eliad Peller
John W. Linville
Ido Yariv
Alexey Dobriyan
Ohad Ben-Cohen
Shahar Levi
Lucas De Marchi