Commit Graph

176 Commits

Author SHA1 Message Date
Jean Delvare 600a711cfe i2c-mux-gpio: Update documentation
* Document the possibility to pass relative GPIO pin numbers.
* Document what platform device IDs to use, so that they do not
  collide.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
2012-10-05 22:23:54 +02:00
Jean Delvare 01d56a6aa1 i2c-viapro: Add VIA VX900 device ID
The SMBus controller in the VIA VX900 appears to be compatible with
the VIA VX855, so just add the device ID.

This closes kernel bug #43096.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-10-05 22:23:53 +02:00
James Ralston 4a8f1ddde9 i2c-i801: Add Device IDs for Intel Lynx Point-LP PCH
Add the SMBus Device IDs for the Intel Lynx Point-LP PCH.

Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-09-10 10:14:02 +02:00
Daniel Kurtz 636752bcb5 i2c-i801: Enable IRQ for SMBus transactions
Add a new 'feature' to i2c-i801 to enable using PCI interrupts.
When the feature is enabled, then an isr is installed for the device's
PCI IRQ.

An I2C/SMBus transaction is always terminated by one of the following
interrupt sources: FAILED, BUS_ERR, DEV_ERR, or on success: INTR.

When the isr fires for one of these cases, it sets the ->status variable
and wakes up the waitq.  The waitq then saves off the status code, and
clears ->status (in preparation for some future transaction).
The SMBus controller generates an INTR irq at the end of each
transaction where INTREN was set in the HST_CNT register.

No locking is needed around accesses to priv->status since all writes to
it are serialized: it is only ever set once in the isr at the end of a
transaction, and cleared while no interrupts can occur.  In addition, the
I2C adapter lock guarantees that entire I2C transactions for a single
adapter are always serialized.

For this patch, the INTREN bit is set only for SMBus block, byte and word
transactions, but not for I2C reads or writes.  The use of the DS
(BYTE_DONE) interrupt with byte-by-byte I2C transactions is implemented in
a subsequent patch.

The interrupt feature has only been enabled for COUGARPOINT hardware.
In addition, it is disabled if SMBus is using the SMI# interrupt.

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24 14:13:58 +02:00
Jean Delvare 9cd3f2e849 i2c/writing-clients: Mention module_i2c_driver()
Based on a previous patch from Peter Meerwald.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Peter Meerwald <p.meerwald@bct-electronic.com>
2012-07-24 14:13:57 +02:00
Andrew Armenia 2a2f7404a1 i2c-piix4: Support AMD auxiliary SMBus controller
Some AMD chipsets, such as the SP5100, have an auxiliary SMBus
controller with a second set of registers. This patch adds
support for this auxiliary controller.

Tested on ASUS KCMA-D8 motherboard.

Signed-off-by: Andrew Armenia <andrew@asquaredlabs.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-07-24 14:13:57 +02:00
Mark Brown 14674e7011 i2c: Split I2C_M_NOSTART support out of I2C_FUNC_PROTOCOL_MANGLING
Since there are uses for I2C_M_NOSTART which are much more sensible and
standard than most of the protocol mangling functionality (the main one
being gather writes to devices where something like a register address
needs to be inserted before a block of data) create a new I2C_FUNC_NOSTART
for this feature and update all the users to use it.

Also strengthen the disrecommendation of the protocol mangling while we're
at it.

In the case of regmap-i2c we remove the requirement for mangling as
I2C_M_NOSTART is the only mangling feature which is being used.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-05-30 10:55:34 +02:00
Jean Delvare e7065e20d9 i2c: Rename last mux driver to standard pattern
Update the MAINTAINERS entry and all other references accordingly.

Based on an original patch by Wolfram Sang.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>

[wsa: fixed merge conflict due to rework in i2c_add_mux_adapter()]

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-05-12 14:28:18 +02:00
Lucas De Marchi 970e248649 Documentation: remove references to /etc/modprobe.conf
Usage of /etc/modprobe.conf file was deprecated by module-init-tools and
is no longer parsed by new kmod tool. References to this file are
replaced in Documentation, comments and Kconfig according to the
context.

There are also some references to the old /etc/modules.conf from 2.4
kernels that are being removed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-03-30 16:03:15 -07:00
Seth Heasley 062737fb6d i2c-i801: Add device IDs for Intel Lynx Point
Add the SMBus controller device IDs for the Intel Lynx Point PCH.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2012-03-26 21:47:19 +02:00
Roland Stigge 286431048b USB: ohci-nxp: Rename symbols from pnx4008 to nxp
Since this driver is compatible with several NXP devices, the driver was renamed
accordingly. This patch also changes the respective symbol names.

Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-13 14:27:28 -07:00
Jean Delvare cbb4451404 i2c: Fix device name for 10-bit slave address
10-bit addresses overlap with traditional 7-bit addresses, leading in
device name collisions. Add an arbitrary offset to 10-bit addresses to
prevent this collision. The offset was chosen so that the address is
still easily recognizable.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
2011-11-23 11:33:07 +01:00
Jonathan Cameron 06a67848c6 i2c: Functions for byte-swapped smbus_write/read_word_data
Reimplemented at least 17 times discounting error mangling cases
where it could be used.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2011-10-30 13:47:25 +01:00
Seth Heasley 6e2a851e71 i2c-i801: SMBus patch for Intel Panther Point DeviceIDs
This patch adds the SMBus controller DeviceID for the Intel Panther Point PCH.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2011-05-24 20:58:49 +02:00
Vikram Narayanan 3116c86033 i2c/writing-clients: Fix foo_driver.id_table
The i2c_device_id structure variable's name is not used in the
i2c_driver structure.

Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2011-05-24 20:58:48 +02:00
Lucas De Marchi 25985edced Fix common misspellings
Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-31 11:26:23 -03:00
Linus Torvalds 75ea6358bc Merge branch 'for-linus/2639/i2c-2' of git://git.fluff.org/bjdooks/linux
* 'for-linus/2639/i2c-2' of git://git.fluff.org/bjdooks/linux:
  i2c-pxa2xx: Don't clear isr bits too early
  i2c-pxa2xx: Fix register offsets
  i2c-pxa2xx: pass of_node from platform driver to adapter and publish
  i2c-pxa2xx: check timeout correctly
  i2c-pxa2xx: add support for shared IRQ handler
  i2c-pxa2xx: Add PCI support for PXA I2C controller
  ARM: pxa2xx: reorganize I2C files
  i2c-pxa2xx: use dynamic register layout
  i2c-mxs: set controller to pio queue mode after reset
  i2c-eg20t: support new device OKI SEMICONDUCTOR ML7213 IOH
  i2c/busses: Add support for Diolan U2C-12 USB-I2C adapter
2011-03-22 10:05:27 -07:00
Seth Heasley 662cda8abb i2c-i801: SMBus patch for Intel DH89xxCC DeviceIDs
Add the SMBus Controller DeviceIDs for the Intel DH89xxCC PCH.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2011-03-20 14:50:53 +01:00
Jean Delvare ed065e26b8 i2c: Minor fixes to upgrading-clients document
* Typical legacy drivers implemented method .detach_client, not
  .detach_adapter.
* Drop all references to __devexit, as i2c drivers shouldn't use it.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2011-03-20 14:50:52 +01:00
Roman Fietze 6ced9e6b39 i2c: Fix typo in instantiating-devices document
The struct i2c_board_info member holding the name is "type", not
"name".

Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
2011-03-20 14:50:52 +01:00
Guenter Roeck 335d7c58fc i2c/busses: Add support for Diolan U2C-12 USB-I2C adapter
This patch adds support for the Diolan U2C-12 USB-I2C adapter.
It also updates MAINTAINERS to list the author as maintainer.

Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2011-01-27 00:39:30 +00:00
Peter Korsgaard 92ed1a76ca i2c: Add generic I2C multiplexer using GPIO API
Add an i2c mux driver providing access to i2c bus segments using a
hardware MUX sitting on a master bus and controlled through gpio pins.

E.G. something like:

  ----------              ----------  Bus segment 1   - - - - -
 |          | SCL/SDA    |          |-------------- |           |
 |          |------------|          |
 |          |            |          | Bus segment 2 |           |
 |  Linux   | GPIO 1..N  |   MUX    |---------------   Devices
 |          |------------|          |               |           |
 |          |            |          | Bus segment M
 |          |            |          |---------------|           |
  ----------              ----------                  - - - - -

SCL/SDA of the master I2C bus is multiplexed to bus segment 1..M
according to the settings of the GPIO pins 1..N.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2011-01-10 22:11:23 +01:00
David Woodhouse 55fee8d7f7 i2c-i801: Add PCI idents for Patsburg 'IDF' SMBus controllers
These are the extra 'Integrated Device Function' SMBus controllers found
on the Patsburg chipset. Mention the absence of slave mode support.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-31 21:07:00 +01:00
Seth Heasley e30d9859cf i2c-i801: Add Intel Patsburg device ID
Add support for the Intel Patsburg PCH SMBus Controller.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-31 21:06:59 +01:00
Jean Delvare 9a94241afc i2c: Add support for custom probe function
The probe method used by i2c_new_probed_device() may not be suitable
for all cases. Let the caller provide its own, optional probe
function.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2010-08-11 18:20:56 +02:00
Justin P. Mattock 0ea6e61122 Documentation: update broken web addresses.
Below you will find an updated version from the original series bunching all patches into one big patch
updating broken web addresses that are located in Documentation/*
Some of the addresses date as far far back as 1995 etc... so searching became a bit difficult,
the best way to deal with these is to use web.archive.org to locate these addresses that are outdated.
Now there are also some addresses pointing to .spec files some are located, but some(after searching
on the companies site)where still no where to be found. In this case I just changed the address
to the company site this way the users can contact the company and they can locate them for the users.

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Cc: Paulo Marques <pmarques@grupopie.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Michael Neuling <mikey@neuling.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-08-04 15:21:40 +02:00
Andrea Gelmini 89140f4157 Documentation/i2c: Checkpatch cleanup
Remove all trailing whitespace in Documentation/i2c.

Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-06-03 11:33:50 +02:00
Jean Delvare adff687d8c i2c-i801: Let the user disable selected driver features
Let the user disable selected features normally supported by the
device. This makes it possible to work around possible driver or
hardware bugs if the feature in question doesn't work as intended
for whatever reason.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Felix Rubinstein <felixru@gmail.com>
2010-05-21 18:40:54 +02:00
Wolfram Sang e4a7b9b04d i2c-core: Erase pointer to clientdata on removal
After discovering that a lot of i2c-drivers leave the pointer to their
clientdata dangling, it was decided to let the core handle this issue.
It is assumed that the core may access the private data after remove()
as there are no guarantees for the lifetime of such pointers anyhow (see
thread starting at http://lkml.org/lkml/2010/3/21/68)

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-05-04 11:09:27 +02:00
Zhangfei Gao 0c43ea544c i2c: Document the message size limit
i2c_master_send & i2c_master_recv do not support more than 64 kb
transfer, since msg.len is u16.

Signed-off-by: Zhangfei Gao <zgao6@marvell.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-03-02 12:23:49 +01:00
Jean Delvare 927ab2f807 i2c-parport-light: Add SMBus alert support
Add support for the SMBus alert mechanism to the i2c-parport-light
driver. The ADM1032 evaluation board at least is properly wired for
this.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Trent Piepho <tpiepho@freescale.com>
2010-03-02 12:23:45 +01:00
Jean Delvare 3585925448 i2c-parport: Add SMBus alert support
Add support for the SMBus alert mechanism to the i2c-parport driver.
The ADM1032 evaluation board at least is properly wired for this.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Trent Piepho <tpiepho@freescale.com>
2010-03-02 12:23:44 +01:00
Jean Delvare b5527a7766 i2c: Add SMBus alert support
SMBus alert support. The SMBus alert protocol allows several SMBus
slave devices to share a single interrupt pin on the SMBus master,
while still allowing the master to know which slave triggered the
interrupt.

This is based on preliminary work by David Brownell. The key
difference between David's implementation and mine is that his was
part of i2c-core, while mine is split into a separate, standalone
module named i2c-smbus. The i2c-smbus module is meant to include
support for all SMBus extensions to the I2C protocol in the future.

The benefit of this approach is a zero cost for I2C bus segments which
do not need SMBus alert support. Where David's implementation
increased the size of struct i2c_adapter by 7% (40 bytes on i386),
mine doesn't touch it. Where David's implementation added over 150
lines of code to i2c-core (+10%), mine doesn't touch it. The only
change that touches all the users of the i2c subsystem is a new
callback in struct i2c_driver (common to both implementations.) I seem
to remember Trent was worried about the footprint of David'd
implementation, hopefully mine addresses the issue.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Trent Piepho <tpiepho@freescale.com>
2010-03-02 12:23:42 +01:00
Seth Heasley 393764340b i2c-i801: Add Intel Cougar Point device IDs
Add the Intel Cougar Point (PCH) SMBus controller device IDs.

Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-03-02 12:23:39 +01:00
Jean Delvare c3813d6af1 i2c: Get rid of struct i2c_client_address_data
Struct i2c_client_address_data only contains one field at this point,
which makes its usefulness questionable. Get rid of it and pass simple
address lists around instead.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
2009-12-14 21:17:25 +01:00
Jean Delvare 6471b68982 i2c-stub: Documentation update
There is nothing sensors-specific to i2c-stub.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-06 17:06:30 +01:00
Jean Delvare 38f41f282f i2c-stub: Allow user to disable some commands
Add a module parameter to override the functionality bitfield. This
lets the user disable some commands. This can be used to force a chip
driver to take different code paths.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-06 17:06:29 +01:00
Jean Delvare 4710317891 i2c-stub: Implement I2C block support
This is required to test some drivers, for example at24.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-06 17:06:28 +01:00
Jean Delvare c7b25a9e96 i2c: Drop probe, ignore and force module parameters
The legacy probe and force module parameters are obsolete now, the
same can be achieved using the new_device sysfs interface, which is
both more flexible and cheaper (it is implemented by i2c-core rather
than replicated in every driver module.)

The legacy ignore module parameters can be dropped as well. Ignoring
can be done by instantiating a "dummy" device at the problematic
address.

This is the first step of a huge cleanup to i2c-core's i2c_detect
function, i2c.h's I2C_CLIENT_INSMOD* macros, and all drivers that made
use of them.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-12-06 17:06:24 +01:00
Jean Delvare a0c11cdd6a i2c-voodoo3: Delete
Superseded by tdfxfb. I2C/DDC support used to live in a separate
driver but this caused driver conflicts.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
2009-12-06 17:06:21 +01:00
Crane Cai 3806e94b01 i2c-piix4: Modify code name SB900 to Hudson-2
Change SB900 to its formal code name Hudson-2.

Signed-off-by: Crane Cai <crane.cai@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-11-07 13:10:46 +01:00
Jean Delvare 03f1805ad0 i2c: Minor documentation update
The sysfs path to i2c adapters has changed recently, update the
documentation to reflect that change.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-10-04 22:53:45 +02:00
Jean Delvare f546c65cd5 i2c: Move misc devices documentation
Some times ago the eeprom and max6875 drivers moved to
drivers/misc/eeprom, but their documentation did not follow. It's
finally time to get rid of Documentation/i2c/chips.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Gardner <gardner.ben@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
2009-10-04 22:53:40 +02:00
Crane Cai 76b3e28fa7 i2c-piix4: Add AMD SB900 SMBus device ID
Add new SMBus device ID for AMD SB900.

Signed-off-by: Crane Cai <crane.cai@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-09-18 22:45:50 +02:00
Wolfram Sang e7c5c49ecd i2c/chips: Remove deprecated pcf8574 driver
The pcf8574 driver in drivers/i2c/chips which just exports its register to
sysfs is superseded by drivers/gpio/pcf857x.c which properly uses the gpiolib.
As this driver has been deprecated for more than a year, finally remove it.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-09-18 22:45:49 +02:00
Wolfram Sang 732d481127 i2c/chips: Remove deprecated pca9539 driver
The pca9539 driver in drivers/i2c/chips which just exports its registers to
sysfs is superseded by drivers/gpio/pca953x.c which properly uses the gpiolib.
As this driver has been deprecated for more than a year, finally remove it.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-09-18 22:45:48 +02:00
Wolfram Sang 8f67eeb0b4 i2c/chips: Remove deprecated pcf8575 driver
The pcf8575 driver in drivers/i2c/chips which just exports its register to
sysfs is superseded by drivers/gpio/pcf857x.c which properly uses the gpiolib.
As this driver has been deprecated for more than a year, finally remove it.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-09-18 22:45:48 +02:00
Jean Delvare 99cd8e2587 i2c: Add a sysfs interface to instantiate devices
Add a sysfs interface to instantiate and delete I2C devices. This is
primarily a replacement of the force_* module parameters implemented
by some i2c drivers. These module parameters were implemented
internally by the I2C_CLIENT_INSMOD* macros, which don't scale well.

This can also be used when developing a driver on a self-soldered
board which doesn't yet have proper I2C device declaration at the
platform level, and presumably for various debugging situations.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
2009-06-19 16:58:20 +02:00
Jean Delvare 729d6dd571 i2c: Get rid of the legacy binding model
We converted all the legacy i2c drivers so we can finally get rid of
the legacy binding model. Hooray!

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
2009-06-19 16:58:18 +02:00
Harald Welte a231591f04 i2c-viapro: Add new PCI device ID for VX855
The south bridge of the VIA VX855 chipset has a different PCI Device ID
so i2c-viapro.c needs to be updated with this.

Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2009-06-15 18:01:49 +02:00