In WoWLAN, we only get the triggers when we actually get
to suspend. As a consequence, drivers currently don't
know that the device should enable wakeup. However, the
device_set_wakeup_enable() API is intended to be called
when the wakeup is enabled, not later when needed.
Add a new set_wakeup() call to cfg80211 and mac80211 to
allow drivers to properly call device_set_wakeup_enable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report Toffset to userspace.
Let userspace select the mesh synchronization method.
Signed-off-by: Marco Porsch <marco.porsch@s2005.tu-chemnitz.de>
Signed-off-by: Pavel Zubarev <pavel.zubarev@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the plan to change mac80211's queue API to
not map ACs to queues 1:1, it seems necessary to
clarify some APIs that act on ACs rather than on
queues to spell that out explicitly. Do this.
Also verify that the AC number given is valid.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Free extra as done in the error-handling code just above.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nl80211 handling code should ensure as much as
it can that the interface is in a valid state, it
can certainly ensure the interface is running.
Not doing so can cause calls through mac80211 into
the driver that result in warnings and unspecified
behaviour in the driver.
Cc: stable@vger.kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
The station_info struct had demanded dBm signal values, but the
cfg80211 wireless extensions implementation was also accepting
"unspecified" (i.e. RSSI) unit values while the nl80211 code was
completely unaware of them. Resolve this by formally allowing the
"unspecified" units while making nl80211 ignore them.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
This is intended to be the timestamp sent by the
peer in the beacon/probe response, not any form
of host timestamp. Clarify the documentation and
variable names.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Receive background scan period as part of connect
command and pass the same to the driver.
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the signal strength (in dBm only for now) to
frames that are received via nl80211's various
frame APIs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds an attribute, NL80211_ATTR_INACTIVITY_TIMEOUT,
to set the inactivity timeout which can be used to remove the
station in AP mode. This can be passed in NL80211_CMD_START_AP
and used by the drivers which have AP MLME in firmware but
don't support get_station() properly. To disable inactivity
timer in userspace, wpa_s for example, there is a new flag,
NL80211_FEATURE_INACTIVITY_TIMER, in nl80211_feature_flags
through which drivers can register their capability to use
the inactivity timeout to free the stations.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh peer links are established only if average rssi of the peer
candidate satisfies the threshold. This is not in 802.11s specification
but was requested by David Fulgham, an open80211s user. This is a way to avoid
marginal peer links with stations that are barely within range.
This patch adds a new mesh configuration parameter, mesh_rssi_threshold. This
feature is supported only for hardwares that report signal in dBm.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In "cfg80211: no cookies in cfg80211_send_XXX()"
Holger Schurig removed the cookies in the calls
from mac80211 to cfg80211, but the ones in the
other direction were left in. Remove them now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AP/GO mode API isn't very clearly defined, it
has "set beacon" and "new beacon" etc.
Modify the API to the following:
* start AP -- all settings
* change beacon -- new beacon data
* stop AP -- stop AP mode operation
This also reflects in the nl80211 API, rename
the commands there correspondingly (but keep
the old names for compatibility.)
Overall, this makes it much clearer what's going
on in the API.
Kalle developed the ath6kl changes, I created
the rest of the patch.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ridx" is used as an index into the mcs_mask[] array which has
IEEE80211_HT_MCS_MASK_LEN elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the IBSS network is RSN-protected, let userspace authorize the stations
instead of adding them as AUTHORIZED by default.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed by mac80211 to keep a reference
to a BSS alive for the auth process. Remove the
old version of cfg80211_ref_bss() since it's
not actually used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To track authenticated state seems to have been
a design mistake in cfg80211. It is possible to
have out of band authentication (FT), tracking
multiple authentications caused more problems
than it ever helped, and the implementation in
mac80211 is too complex.
Remove all this complexity, and let userspace
do whatever it wants to, mac80211 can deal with
that just fine. Association is still tracked of
course, but authentication no longer is. Local
auth state changes are thus no longer of value,
so ignore them completely.
This will also help implement SAE -- asking the
driver to do an authentication is now almost
equivalent to sending an authentication frame,
with the exception of shared key authentication
which is still handled completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow to set mcs masks through nl80211. We also allow to set MCS
rates but no legacy rates (and vice versa).
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A mesh node that joins the mesh network is by default a forwarding entity. This patch allows
the mesh node to set as non-forwarding entity. Whenever dot11MeshForwarding is set to 0, the
mesh node can prevent itself from forwarding the traffic which is not destined to him.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems that -Wshadow is no longer default in
sparse runs, but let's fix the warnings anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The local maximum transmit power is the maximum power a wireless device
allowed to transmit. If Power Constraint is presented, the local maximum
power equals to the maximum allowed power defined in regulatory domain
minus power constraint.
The maximum transmit power is maximum power a wireless device capable of
transmitting, and should be used in Power Capability element (7.3.2.16
IEEE802.11 2007).
The transmit power from a wireless device should not greater than the
local maximum transmit power.
The maximum transmit power was not calculated correctly in the current
Linux wireless/mac80211 when Power Constraint is presented.
Signed-off-by: Hong Wu <hong.wu@dspg.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My patch to validate station flags broke compatibility
with the old station flags setting where all flags are
always set at once since it always set the mask as all
possible flags which ended up being rejected later in
the station add/modify code.
Fix by parsing only the current flags in the old flags
attribute -- new applications and new flags should use
(and will now require) the new flags attribute where
the mask is given by the application.
Reported-and-tested-by: Thomas Hilber <ath9k-dev@toh.cx>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wireless will select a different hardware queue based on the
top 3 bits of the diffserv field, for ipv4. Extend that queue
selection mechanism to ipv6, and make the calls orthogonal.
Signed-off-by: Dave Täht <dave.taht@bufferbloat.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Following the tradition we have had with ath5k, ath9k, CRDA,
wireless-regdb I'd like to license this code under the permissive ISC
license for the code sharing purposes with other OSes, it'd sure be nice
to help the landscape in this area. Although I am %82.89 owner of the
regulatory code I have asked every contributor to the regulatory code
and have receieved positive Acked-bys from everyone except two deceased
entities:
o Frans Pop RIP 2010 [0]
- Frans Pop <elendil@planet.nl>
- Frans Pop <fjp@debian.org>
o Nokia RIP February, 11, 2011 [1], [2]
- ext-yuri.ershov@nokia.com
- kalle.valo@nokia.com
Frans Pop's contribution was a simple patch 55f98938, titled,
"wireless: remove trailing space in messages" which just add a \n
to some printk lines. I'm going to treat these additions as
uncopyrightable.
As for the contributions made by employees on behalf of Nokia
my contact point was Petri Karhula <petri.karhula@nokia.com> but
after one month he noted he had not been able to get traction from the
legal department on this request, as such it I proceeded by replacing
their contributions in previous patches.
The end goal is to help a clean rewrite that starts in userspace
that is shared under ISC license which currently is taking place with
the regulatory simulator [3].
[0] http://lists.debian.org/debian-devel/2011/12/msg00263.html
[1] http://press.nokia.com/2011/02/11/nokia-outlines-new-strategy-introduces-new-leadership-operational-structure/
[2] http://NokiaPlanB.com
[3] git://github.com/mcgrof/regsim.git
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Acked-by: Mihai Moldovan <ionic@ionic.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Tony Vroon <tony@linx.net>
Acked-by: Pavel Roskin <proski@gnu.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Acked-by: Pat Erley <pat-lkml@erley.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Joe Perches <joe@perches.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: John Gordon <john@devicescape.com>
Acked-by: Simon Barber <protocolmagic@gmail.com>
Acked-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: Jiri Benc <jbenc@upir.cz>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Scott James Remnant <keybuk@google.com>
Acked-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nokia hasn't gotten back to me in over 1 month for a relicense
change request. There are only a few changes that they contributed,
so just reverting their changes but replacing with another set.
This change replaces this commit:
commit 269ac5fd2d
Author: Kalle Valo <kalle.valo@nokia.com>
Date: Tue Dec 1 10:47:15 2009 +0200
cfg80211: indent regulatory messages with spaces
The regulatory messages in syslog look weird:
kernel: cfg80211: Regulatory domain: US
kernel: ^I(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
kernel: ^I(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
kernel: ^I(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
kernel: ^I(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
kernel: ^I(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
kernel: ^I(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
kernel: ^I(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
Indent them with four spaces instead of the tab character to get prettier
output.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Petri Karhula <petri.karhula@nokia.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nokia hasn't gotten back to me in over 1 month for a relicense
change request. There are only a few changes that they contributed,
so just reverting their changes but replacing with another set.
This change replaces this commit:
commit c4c322941c
Author: Yuri Ershov <ext-yuri.ershov@nokia.com>
Date: Tue Jun 29 15:08:08 2010 +0400
cfg80211: Update of regulatory request initiator handling
In some cases there could be possible dereferencing freed pointer. The
update is intended to avoid this issue.
Signed-off-by: Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Petri Karhula <petri.karhula@nokia.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If station info contains a beacon loss count, return
it to userspace.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we restore regulatory settings the world regulatory domain
is properly reset on cfg80211 (or user prefered regulatory domain)
but we were never setting back channel values for drivers that use
WIPHY_FLAG_CUSTOM_REGULATORY. Set these values up again by using
the orig_ channel parameters.
This fixes restoring custom regulatory settings upon disconnect
events.
Cc: compat@orbit-lab.org
Cc: Paul Stewart <pstew@google.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Senthilkumar Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By definition WIPHY_FLAG_STRICT_REGULATORY was intended to allow the
wiphy to adjust itself to the country IE power information if the
card had no regulatory data but we had no way to tell cfg80211 that if
the card also had its own custom regulatory domain (these are typically
custom world regulatory domains) that we want to follow the country IE's
noted values for power for each channel. We add support for this and
document it.
This is not a critical fix but a performance optimization for cards
with custom regulatory domains that associate to an AP with sends
out country IEs with a higher EIRP than the one on the custom
regulatory domain. In practice the only driver affected right now
are the Atheros drivers as they are the only drivers using both
WIPHY_FLAG_STRICT_REGULATORY and WIPHY_FLAG_CUSTOM_REGULATORY --
used on cards that have an Atheros world regulatory domain. Cards
that have been programmed to follow a country specifically will not
follow the country IE power. So although not a stable fix distributions
should consider cherry picking this.
Cc: compat@orbit-lab.org
Cc: Paul Stewart <pstew@google.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Senthilkumar Balasubramanian <senthilb@qca.qualcomm.com>
Reported-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nl80211 station handling code is a bit messy
and doesn't do a lot of validation. It seems like
this could be an issue for drivers that don't use
mac80211 to validate everything.
As cfg80211 doesn't keep station state, move the
validation of allowing supported_rates to change
for TDLS only in station mode to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was evidently missed in the TDLS patch (07ba55d7).
Cc: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All nl80211 commands that need only the wiphy
still allow identifying it by giving an interface
index, except, as Kenny pointed out, the testmode
dump support.
Fix this by looking up the wiphy via the ifidx in
this case as well.
Tested-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Regulatory updates set by CORE are ignored for custom regulatory cards.
Let us notify the changes to the driver, as some drivers uses core hint
to restore its orig_* reg domain setting.
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is quite possible to run into a race in bss timeout where
the drivers see the bss entry just before notifying cfg80211
of a roaming event but it got timed out by the time rdev->event_work
got scehduled from cfg80211_wq. This would result in the following
WARN-ON() along with the failure to notify the user space of
the roaming. The other situation which is happening with ath6kl
that runs into issue is when the driver reports roam to same AP
event where the AP bss entry already got expired. To fix this,
move cfg80211_get_bss() from __cfg80211_roamed() to cfg80211_roamed().
[158645.538384] WARNING: at net/wireless/sme.c:586
__cfg80211_roamed+0xc2/0x1b1()
[158645.538810] Call Trace:
[158645.538838] [<c1033527>] warn_slowpath_common+0x65/0x7a
[158645.538917] [<c14cfacf>] ? __cfg80211_roamed+0xc2/0x1b1
[158645.538946] [<c103354b>] warn_slowpath_null+0xf/0x13
[158645.539055] [<c14cfacf>] __cfg80211_roamed+0xc2/0x1b1
[158645.539086] [<c14beb5b>] cfg80211_process_rdev_events+0x153/0x1cc
[158645.539166] [<c14bd57b>] cfg80211_event_work+0x26/0x36
[158645.539195] [<c10482ae>] process_one_work+0x219/0x38b
[158645.539273] [<c14bd555>] ? wiphy_new+0x419/0x419
[158645.539301] [<c10486cb>] worker_thread+0xf6/0x1bf
[158645.539379] [<c10485d5>] ? rescuer_thread+0x1b5/0x1b5
[158645.539407] [<c104b3e2>] kthread+0x62/0x67
[158645.539484] [<c104b380>] ? __init_kthread_worker+0x42/0x42
[158645.539514] [<c151309a>] kernel_thread_helper+0x6/0xd
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code has been on the list to remove for a long
time, so disable it by default, add a warning to its
Kconfig, and schedule it for removal in 3.5.
The only known dependency, hal, has not required it
since its 0.5.12 release, which was in early 2009
and hal has since been deprecated completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prepare cfg80211 for IBSS HT:
* extend cfg80211 ibss struct with channel_type
* Check if extension channel can be used
* Export can_beacon_sec_chan for use in mac80211 (will be called
from ibss.c later).
Signed-off-by: Alexander Simon <an.alexsimon@googlemail.com>
[siwu@hrz.tu-chemnitz.de: Updates]
* fix cfg80211_can_beacon_ext_chan comment
* remove implicit channel_type enum assumptions
* remove radar channel flags check
* add HT IBSS feature flag
* reword commit message
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes' patch for "cfg80211: fix regulatory NULL dereference"
broke user regulaotry hints and it did not address the fact that
last_request was left populated even if the previous regulatory
hint was stale due to the wiphy disappearing.
Fix user reguluatory hints by only bailing out if for those
regulatory hints where a request_wiphy is expected. The stale last_request
considerations are addressed through the previous fixes on last_request
where we reset the last_request to a static world regdom request upon
reset_regdomains(). In this case though we further enhance the effect
by simply restoring reguluatory settings completely.
Cc: stable@vger.kernel.org
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a theoretical race that if hit will trigger
a crash. The race is between when we issue the first
regulatory hint, regulatory_hint_core(), gets processed
by the workqueue and between when the first device
gets registered to the wireless core. This is not easy
to reproduce but it was easy to do so through the
regulatory simulator I have been working on. This
is a port of the fix I implemented there [1].
[1] a246ccf81f
Cc: stable@vger.kernel.org
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As per 802.11mb 13.9.11.3
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains the configuration changes in nl80211/cfg80211.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MAC addresses have a fixed length. The current
policy allows passing < ETH_ALEN bytes, which
might result in reading beyond the buffer.
Cc: stable@vger.kernel.org
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sparse reports:
net/wireless/util.c:499:30: error: cannot size expression
net/wireless/util.c:503:30: error: cannot size expression
This is evidently due to the EXPORT_SYMBOL() of the
bridge_tunnel_header and rfc1042 header variables.
Move them to the end of the file to work around the
sparse issue. The error itself from sparse can be
ignored safely, but since sparse stops parsing at
errors, other issues after this would go undetected.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows users to disable features such as HT, HT40,
and to modify the MCS, AMPDU, and AMSDU settings for
drivers that support it.
The MCS, AMPDU, and AMSDU features that may be disabled are
are reported in the phy-info netlink message as a mask.
Attemping to disable features that are not supported will
take no affect, but will not return errors. This is to aid
backwards compatibility in user-space apps that may not be
clever enough to deal with parsing the the capabilities mask.
This patch only enables the infrastructure. An additional
patch will enable the feature in mac80211.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No other driver ever ended up using this, and
the commit forgot to move the prototype so no
driver could have used it. Revert it, if any
driver shows up and needs it it can be moved
again, but until then it's more efficient to
have it in mac80211 where the only user is.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_vlan() sets the output parameter even if it
returns an error, which is a bit odd. Instead,
convert it to use ERR_PTR.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently mac80211 implements these for all devices,
but given restrictions of some devices that isn't
really true, so prepare for being able to remove the
capability for some mac80211 devices.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
User space might want to test if driver supports testmode. Adding testmode
to the list of supported commands makes this easier.
I omitted testmode_dump() in purpose. I assume all drivers implementing
testmode_dump() will also implement testmode_cmd().
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This grants drivers access to the DFS region that a
regulatory domain belongs to.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wireless-regdb now has support for mapping a country to
one DFS region. CRDA sends this to us now so process it
so we can provide that hint to drivers. This will later be
used by code for processing DFS in a way that meets the
criteria for the DFS region the country belongs to.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By the time userspace returns with a response to
the regulatory domain request, the wiphy causing
the request might have gone away. If this is so,
reject the update but mark the request as having
been processed anyway.
Cc: Luis R. Rodriguez <lrodriguez@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass probe-response data from usermode via beacon parameters.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Notify user-space about probe-response offloading support in the driver.
A wiphy flag is used to indicate support and a bitmap of protocols
determines which protocols are supported.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John reported the following warning:
net/wireless/nl80211.c: In function ‘nl80211_tx_mgmt’:
net/wireless/nl80211.c:5286:8: warning: ‘hdr’ may be used uninitialized in this function
Evidently, his version of gcc isn't able to see that
when "msg" is initialized, "hdr" must also be. My
gcc, 4.6.1, can actually see that and doesn't warn.
Simply initialize the variable to NULL. That means
if the compiler was ever right we'll crash though so
isn't really optimal since it may hide warnings from
the compiler when somebody modifies this code in the
future.
Reported-by: John Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just add API to get the channel & report it. Trivial really.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The problem with PSM when a hidden SSID was used was originally
reported by Juuso Oikarinen.
- When generally scanning, the AP is getting a bss entry with
a zero SSID.
- When associating, a probe-req is sent to the AP with the SSID,
and as a result a probe-response is received with the hidden
SSID in place. As a consequence, a second bss entry is created
for the AP, now with the real SSID.
- After association, mac80211 executes ieee80211_recalc_ps(),
but does not switch to powersave because the beacon-ies are missing.
As result, the STA does not ever enter PSM.
The patch merges in beacon ies of hidden bss from beacon to the probe
response, creating a consistent set of ies in place.
Patch is depended on "cfg80211: fix cmp_ies" made by Johannes.
Signed-off-by: Dmitry Tarnyagin <dmitry.tarnyagin@stericsson.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new wifi socket TX capability should be
supported by wifi drivers, let them advertise
whether they do or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For probe responses it can be useful to not wait for ACK to
avoid retransmissions if the station that sent the probe is
already on the next channel, so allow userspace to request
not caring about the ACK with a new nl80211 flag.
Since mac80211 needs to be updated for the new function
prototype anyway implement it right away -- it's just a
few lines of code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The frames are used by AP/STA WDS mode, and hostapd
needs to know when such a frame was received to set
up the VLAN appropriately to allow using it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the ability to register to received beacon frames
to allow implementing OLBC logic in userspace. The
registration is per wiphy since there's no point in
receiving the same frame multiple times.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the AP SME in hostapd is used it wants to
probe the clients when they have been idle for
some time. Add explicit API to support this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the ability to advertise that the device
contains the AP SME and what features it can
support. There are currently no features in
the bitmap -- probe response offload will be
advertised by a few patches Arik is working
on now (who took over from Guy Eilam) and a
device with AP SME will typically implement
and require response offload.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To implement AP mode without monitor interfaces we
need to be able to send a deauth to stations that
send frames without being associated. Enable this
by adding a new nl80211 event for such frames that
an application can subscribe to.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WPI-SMS4 uses 16-octet PN field, so we need to allow longer key
sequence values to be configured.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 4d9d88d1 by Scott James Remnant <keybuk@google.com> added
the .uevent() callback for the regulatory device used during
the platform device registration. The change was done to account
for queuing up udev change requests through udevadm triggers.
The change also meant that upon regulatory core exit we will now
send a uevent() but the uevent() callback, reg_device_uevent(),
also accessed last_request. Right before commiting device suicide
we free'd last_request but never set it to NULL so
platform_device_unregister() would lead to bogus kernel paging
request. Fix this and also simply supress uevents right before
we commit suicide as they are pointless.
This fix is required for kernels >= v2.6.39
$ git describe --contains 4d9d88d1
v2.6.39-rc1~468^2~25^2^2~21
The impact of not having this present is that a bogus paging
access may occur (only read) upon cfg80211 unload time. You
may also get this BUG complaint below. Although Johannes
could not reproduce the issue this fix is theoretically correct.
mac80211_hwsim: unregister radios
mac80211_hwsim: closing netlink
BUG: unable to handle kernel paging request at ffff88001a06b5ab
IP: [<ffffffffa030df9a>] reg_device_uevent+0x1a/0x50 [cfg80211]
PGD 1836063 PUD 183a063 PMD 1ffcb067 PTE 1a06b160
Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
CPU 0
Modules linked in: cfg80211(-) [last unloaded: mac80211]
Pid: 2279, comm: rmmod Tainted: G W 3.1.0-wl+ #663 Bochs Bochs
RIP: 0010:[<ffffffffa030df9a>] [<ffffffffa030df9a>] reg_device_uevent+0x1a/0x50 [cfg80211]
RSP: 0000:ffff88001c5f9d58 EFLAGS: 00010286
RAX: 0000000000000000 RBX: ffff88001d2eda88 RCX: ffff88001c7468fc
RDX: ffff88001a06b5a0 RSI: ffff88001c7467b0 RDI: ffff88001c7467b0
RBP: ffff88001c5f9d58 R08: 000000000000ffff R09: 000000000000ffff
R10: 0000000000000000 R11: 0000000000000001 R12: ffff88001c7467b0
R13: ffff88001d2eda78 R14: ffffffff8164a840 R15: 0000000000000001
FS: 00007f8a91d8a6e0(0000) GS:ffff88001fc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffff88001a06b5ab CR3: 000000001c62e000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process rmmod (pid: 2279, threadinfo ffff88001c5f8000, task ffff88000023c780)
Stack:
ffff88001c5f9d98 ffffffff812ff7e5 ffffffff8176ab3d ffff88001c7468c2
000000000000ffff ffff88001d2eda88 ffff88001c7467b0 ffff880000114820
ffff88001c5f9e38 ffffffff81241dc7 ffff88001c5f9db8 ffffffff81040189
Call Trace:
[<ffffffff812ff7e5>] dev_uevent+0xc5/0x170
[<ffffffff81241dc7>] kobject_uevent_env+0x1f7/0x490
[<ffffffff81040189>] ? sub_preempt_count+0x29/0x60
[<ffffffff814cab1a>] ? _raw_spin_unlock_irqrestore+0x4a/0x90
[<ffffffff81305307>] ? devres_release_all+0x27/0x60
[<ffffffff8124206b>] kobject_uevent+0xb/0x10
[<ffffffff812fee27>] device_del+0x157/0x1b0
[<ffffffff8130377d>] platform_device_del+0x1d/0x90
[<ffffffff81303b76>] platform_device_unregister+0x16/0x30
[<ffffffffa030fffd>] regulatory_exit+0x5d/0x180 [cfg80211]
[<ffffffffa032bec3>] cfg80211_exit+0x2b/0x45 [cfg80211]
[<ffffffff8109a84c>] sys_delete_module+0x16c/0x220
[<ffffffff8108a23e>] ? trace_hardirqs_on_caller+0x7e/0x120
[<ffffffff814cba02>] system_call_fastpath+0x16/0x1b
Code: <all your base are belong to me>
RIP [<ffffffffa030df9a>] reg_device_uevent+0x1a/0x50 [cfg80211]
RSP <ffff88001c5f9d58>
CR2: ffff88001a06b5ab
---[ end trace 147c5099a411e8c0 ]---
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Scott James Remnant <keybuk@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
genlmsg_end() cannot fail, it just returns the length
of the message. Thus, error handling for it is useless.
While removing it, I also noticed a useless variable
and removed this it as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When comparing two items by IE, the sort order
wasn't stable, which could lead to issues in the
rbtree. Make it stable by making a missing IE
sort before a present IE.
Also sort by length first if it differs and then
by contents.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In other modes the parameters should not be set.
Right now, mac80211 will set them, even if the
user asked for setting them on VLANs which the
driver doesn't know about, causing all kinds of
trouble.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the NL80211_ATTR_HT_CAPABILITY attribute is
used as a struct, it needs a minimum, not maximum
length. Enforce that properly. Not doing so could
potentially lead to reading after the buffer.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These files are non modular, but need to export symbols using
the macros now living in export.h -- call out the include so
that things won't break when we remove the implicit presence
of module.h from everywhere.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files were getting access to these two via the implicit
presence of module.h everywhere. They aren't modules, so they
don't need the full module.h inclusion though.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reuse the already existing struct nl80211_sta_flag_update to specify
both, a flag mask and the flag set itself. This means
nl80211_sta_flag_update is now used for setting station flags and also
for getting station flags.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mark the STA entries of enabled TDLS peers with a new "peer authorized"
flag.
During link setup, allow special TDLS setup frames through the AP, but
otherwise drop all packets destined to the peer. This is required by the
TDLS (802.11z) specification in order to prevent reordering of MSDUs
between the AP and direct paths.
When setup completes and the peer is authorized, send data directly,
bypassing the AP.
In the Rx path, allow data to be received directly from TDLS peers.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When adding a TDLS peer STA, mark it with a new flag in both nl80211 and
mac80211. Before adding a peer, make sure the wiphy supports TDLS and
our operating mode is appropriate (managed).
In addition, make sure all peers are removed on disassociation.
A TDLS peer is first added just before link setup is initiated. In later
setup stages we have more info about peer supported rates, capabilities,
etc. This info is reported via nl80211_set_station().
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for sending high-level TDLS commands and TDLS frames via
NL80211_CMD_TDLS_OPER and NL80211_CMD_TDLS_MGMT, respectively. Add
appropriate cfg80211 callbacks for lower level drivers.
Add wiphy capability flags for TDLS support and advertise them via
nl80211.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when hostapd sets the station as authorized
we also overwrite its uAPSD parameter. This obviously
leads to buggy behaviour (later, with my patches that
actually add uAPSD support). To fix this, only apply
those parameters if they were actually set in nl80211,
and to achieve that add a bitmap of things to apply.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct flag usage - use it as a bit index instead of a bit value.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx params are currently configured per hw, although they
should be configured per interface.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new nl80211 attribute to specify whether to send the management
frames in CCK rate or not. As of now the wpa_supplicant is disabling
CCK rate at P2P init itself. So this patch helps to send P2P probe
request/probe response/action frames being sent at non CCK rate in 2GHz
without disabling 11b rates.
This attribute is used with NL80211_CMD_TRIGGER_SCAN and
NL80211_CMD_FRAME commands to disable CCK rate for management frame
transmission.
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using a hardcoded list of cipher suites in nl80211.c, use a
shared function in util.c to verify that the driver advertises support
for the specified cipher. This provides more accurate validation of the
values and allows vendor-specific cipher suites to be added in drivers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NL80211_ATTR_AKM_SUITES can be used to configure new AKMs, like FT or
the SHA-256 -based AKMs or FT from 802.11r/802.11w. In addition, vendor
specific AKMs could be used. The current validation code for the connect
command prevents cfg80211-based drivers from using these mechanisms even
if the driver would not actually use this AKM value (i.e., it uses
WPA/RSN IE from user space). mac80211-based drivers allow any AKM to be
used since this value is not used there.
Remove the unnecessary validation step in cfg80211 to allow drivers to
decide what AKMs are supported. In theory, we could handle this by
advertising supported AKMs, but that would not be very effective unless
we enforce all drivers (including mac80211) to advertise the set of
supported AKMs. This would require additional changes in many places
whenever a new AKM is introduced even though no actually functionality
changes may be required in most drivers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect variable was used in validating the akm_suites array from
NL80211_ATTR_AKM_SUITES. In addition, there was no explicit
validation of the array length (we only have room for
NL80211_MAX_NR_AKM_SUITES).
This can result in a buffer write overflow for stack variables with
arbitrary data from user space. The nl80211 commands using the affected
functionality require GENL_ADMIN_PERM, so this is only exposed to admin
users.
Cc: stable@kernel.org
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_conn_scan allows disabled channels at scan request.
Hence probe request was seen at the disabled one. This patch
ensures that disabled channel never be added into the scan
request's channel list.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the driver (or most likely firmware) decides which AP to use
for roaming based on internal scan result processing, user space
needs to be notified of PMKSA caching candidates to allow RSN
pre-authentication to be used.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IBSS BSSID is never validated, so an
invalid one might end up being used. Fix
this by rejecting invalid configuration.
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add function to find vendor-specific ie (along with
vendor-specific ie struct definition and P2P OUI values)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scan request received from cfg80211_connect do not
have proper rate mast. So the probe request sent on each
channel do not have proper the supported rates ie.
Cc: stable@kernel.org
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During the association, the regulatory is updated by country IE
that reaps the previously found beacons. The impact is that
after a STA disconnects *or* when for any reason a regulatory
domain change happens the beacon hint flag is not cleared
therefore preventing future beacon hints to be learned.
This is important as a regulatory domain change or a restore
of regulatory settings would set back the passive scan and no-ibss
flags on the channel. This is the right place to do this given that
it covers any regulatory domain change.
Cc: stable@kernel.org
Reviewed-by: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The format is intended to be like the subfields
in the QoS Info field, verify that is the case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reorder functions to remove the need for a forward declaration
introduced by the last commit.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: linux-wireless@vger.kernel.org
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function wiphy_update_regulatory() uses the static variable
last_request and thus needs to be called with reg_mutex held.
This is the case for all users in reg.c, but the function was
exported for use by wiphy_register(), from where it is called
without the lock being held.
Fix this by making wiphy_update_regulatory() private and introducing
regulatory_update() as a wrapper that acquires and holds the lock.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: linux-wireless@vger.kernel.org
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Two spaces and the second "KHz" suggest that the code author meant to
print the bandwidth but forgot it. The code appears in commit e702d3cf
already with two spaces and "KHz" in place of the bandwidth.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce filtering for scheduled scans to reduce the number of
unnecessary results (which cause useless wake-ups).
Add a new nested attribute where sets of parameters to be matched can
be passed when starting a scheduled scan. Only scan results that
match any of the sets will be returned.
At this point, the set consists of a single parameter, an SSID. This
can be easily extended in the future to support more complex matches.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add WIPHY_FLAG_AP_UAPSD flag to indicate uapsd support on
AP mode.
Advertise it to userspace by including a new
NL80211_ATTR_SUPPORT_AP_UAPSD attribute.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removing unnecessary messages saves code and text.
Site specific OOM messages are duplications of a generic MM
out of memory message and aren't really useful, so just
delete them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the rssi of the current AP drops, both wpa_supplicant and the
firmware may do a background scan to find a better AP and try to
associate. Since firmware based roaming is faster, inform
wpa_supplicant to avoid roaming and let the firmware decide to
roam if necessary.
For fullmac drivers like ath6kl, it is just enough to provide the
ESSID and the firmware will decide on the BSSID. Since it is not
possible to do pre-auth during roaming for fullmac drivers, the
wpa_supplicant needs to completely disconnect with the old AP and
reconnect with the new AP. This consumes lot of time and it is
better to leave the roaming decision to the firmware.
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new NL80211_ATTR_STA_WME nested attribute that contains
wme params needed by the low-level driver (uapsd_queues and
max_sp).
Add these params to the station_parameters struct as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to set NL80211_MESHCONF_GATE_ANNOUNCEMENTS attribute,
which will advertise this mesh node as being a mesh gate.
NL80211_HWMP_ROOTMODE must be set or this will do nothing.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to set Root Announcement Interval for our mesh
interface. Also, RANN interval is now in proper units of TUs.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fix allows userspace to mark a meshif as a root node.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the mesh peering frames to the format specified in
the recently ratified 802.11s standard. Several changes took place to
make this happen:
- Change RX path to handle new self-protected frames
- Add new Peering management IE
- Remove old Peer Link IE
- Remove old plink_action field in ieee80211_mgmt header
These changes by themselves would either break peering, or work by
coincidence, so squash them all into this patch.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The NL80211_CMD_NEW_BEACON command is, in practice, requesting AP mode
operations to be started. Add new attributes to provide extra IEs
(e.g., WPS IE, P2P IE) for drivers that build Beacon, Probe Response,
and (Re)Association Response frames internally (likely in firmware).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes need from drivers to parse the beacon tail/head data
to figure out what crypto settings are to be used in AP mode in case
the Beacon and Probe Response frames are fully constructed in the
driver/firmware.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes it easier for drivers that generate Beacon and Probe Response
frames internally (in firmware most likely) in AP mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Moving the parsing logic for retrieving the information elements
stored in management frames, e.g. beacons or probe responses,
and making it available to other cfg80211 drivers.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a comment pointing out the use of enum station_info_flags for
all new struct station_info fields. In addition, memset the sinfo
buffer to zero before use on all paths in the current tree to avoid
leaving uninitialized pointers in the data.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 leaves sinfo->assoc_req_ies uninitialized, causing a random
pointer memory access in nl80211_send_station.
Instead of checking if the pointer is null, use sinfo->filled, like
the rest of the fields.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When user space SME/MLME (e.g., hostapd) is not used in AP mode, the
IEs from the (Re)Association Request frame that was processed in
firmware need to be made available for user space (e.g., RSN IE for
hostapd). Allow this to be done with cfg80211_new_sta().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers that support frame transmission with mgmt_tx() may not support
driver-based offchannel TX. Use mgmt_tx_cancel_wait instead of mgmt_tx
when figuring out whether to indicate support for this with
NL80211_ATTR_OFFCHANNEL_TX_OK.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Several uses were missing terminating newlines.
Typo fix and macro neatening.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A lot of code is dedicated to giving drivers the
ability to use cfg80211's wext handlers without
completely converting. However, only orinoco is
currently using this, and it is only partially
using it.
We reduce the size of both the source and binary
by removing those that nobody needs. If a driver
shows up that needs it during conversion, we can
add back those that are needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A lot of drivers erroneously use wext constants
and don't notice since cfg80211.h includes them.
Make this more split up so drivers needing wext
compatibility from cfg80211 need to explicitly
include that from cfg80211-wext.h.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The test is off by one so we'd read past the end of the
wiphy->bands[] array on the next line.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just a typo fix changing regulaotry to regulatory.
Signed-off-by: Mihai Moldovan <ionic@ionic.de>
CC: John W. Linville <linville@tuxdriver.com>
CC: Mohammed Shafi <shafi.wireless@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At the beginning of wiphy_update_regulatory() a check is performed
whether the request is to be ignored. Then the request is sent to
the driver nevertheless. This happens even if last_request points
to NULL, leading to a crash in the driver:
[<bf01d864>] (lbs_set_11d_domain_info+0x28/0x1e4 [libertas]) from [<c03b714c>] (wiphy_update_regulatory+0x4d0/0x4f4)
[<c03b714c>] (wiphy_update_regulatory+0x4d0/0x4f4) from [<c03b4008>] (wiphy_register+0x354/0x420)
[<c03b4008>] (wiphy_register+0x354/0x420) from [<bf01b17c>] (lbs_cfg_register+0x80/0x164 [libertas])
[<bf01b17c>] (lbs_cfg_register+0x80/0x164 [libertas]) from [<bf020e64>] (lbs_start_card+0x20/0x88 [libertas])
[<bf020e64>] (lbs_start_card+0x20/0x88 [libertas]) from [<bf02cbd8>] (if_sdio_probe+0x898/0x9c0 [libertas_sdio])
Fix this by returning early. Also remove the out: label as it is
not any longer needed.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Cc: linux-wireless@vger.kernel.org
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Daniel Mack <daniel@zonque.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 58389c69150e6032504dfcd3edca6b1975c8b5bc
Author: Johannes Berg <johannes.berg@intel.com>
Date: Mon Jul 18 18:08:35 2011 +0200
cfg80211: allow userspace to control supported rates in scan
made single-band cards crash since it would always
access all wiphy->bands[]. Fix this and reject any
attempts in the new helper ieee80211_get_ratemask()
to do the same, rejecting rates configuration for
unsupported bands.
Reported-by: Pavel Roskin <proski@gnu.org>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_netdev_notifier_call() is configuring psm in case
of NL80211_IFTYPE_STATION interface type (on NETDEV_UP).
do the same for NL80211_IFTYPE_P2P_CLIENT interface type.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some P2P scans are not allowed to advertise
11b rates, but that is a rather special case
so instead of having that, allow userspace
to request the rate sets (per band) that are
advertised in scan probe request frames.
Since it's needed in two places now, factor
out some common code parsing a rate array.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some chips may support different lengths of user-supplied IEs with a
single scheduled scan command than with a single normal scan command.
To support this, this patch creates a separate hardware description
element that describes the maximum size of user-supplied information
element data supported in scheduled scans.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some chips can scan more SSIDs with a single scheduled scan command
than with a single normal scan command (eg. wl12xx chips).
To support this, this patch creates a separate hardware description
element that describes the amount of SSIDs supported in scheduled
scans.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we now have the necessary API in place to support
GTK rekeying, applications will need to know whether it
is supported by a device. Add a pseudo-trigger that is
used only to advertise that capability. Also, add some
new triggers that match what iwlagn devices can do.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we try to stop a scheduled scan while it is not running, we should
return -ENOENT instead of simply ignoring the command and returning
success. This is more consistent with other parts of the code.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In certain circumstances, like WoWLAN scenarios,
devices may implement (partial) GTK rekeying on
the device to avoid waking up the host for it.
In order to successfully go through GTK rekeying,
the KEK, KCK and the replay counter are required.
Add API to let the supplicant hand the parameters
to the driver which may store it for future GTK
rekey operations.
Note that, of course, if GTK rekeying is done by
the device, the EAP frame must not be passed up
to userspace, instead a rekey event needs to be
sent to let userspace update its replay counter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the 'driver_initiated' function argument to
__cfg80211_stop_sched_scan() is not 0 then we'll return an
uninitialized 'err' from the function.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a deadlock when rfkill-blocking a wireless interface,
because we were locking the rdev mutex on NETDEV_GOING_DOWN to stop
sched_scans that were eventually running. The rfkill block code was
already holding a mutex under rdev:
kernel: =======================================================
kernel: [ INFO: possible circular locking dependency detected ]
kernel: 3.0.0-rc1-00049-g1fa7b6a #57
kernel: -------------------------------------------------------
kernel: kworker/0:1/4525 is trying to acquire lock:
kernel: (&rdev->mtx){+.+.+.}, at: [<ffffffff8164c831>] cfg80211_netdev_notifier_call+0x131/0x5b0
kernel:
kernel: but task is already holding lock:
kernel: (&rdev->devlist_mtx){+.+.+.}, at: [<ffffffff8164dcef>] cfg80211_rfkill_set_block+0x4f/0xa0
kernel:
kernel: which lock already depends on the new lock.
To fix this, add a new mutex specifically for sched_scan, to protect
the sched_scan_req element in the rdev struct, instead of using the
global rdev mutex.
Reported-by: Duane Griffin <duaneg@dghda.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes when reporting a MIC failure rx->key may be unset. This
code path is hit when receiving a packet meant for a multicast
address, and decryption is performed in HW.
Fortunately, the failing key_idx is not used for anything up to
(and including) usermode, so we allow ourselves to drop it on the
way up when a key cannot be retrieved.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the new consistent dump feature from (generic) netlink
to advertise when dumps are incomplete.
Readers may note that this does not initialize the
rdev->bss_generation counter to a non-zero value. This is
still OK since the value is modified only under spinlock
when the list is modified. Since the dump code holds the
spinlock, the value will either be > 0 already, or the
list will still be empty in which case a consistent dump
will actually be made (and be empty).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Downsteram DEAUTH messages do not refer to a current authentication
attempt -- AUTH responses do. Therefore we should not allow DEAUTH
from an AP to void state for an AUTH attempt in progress.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When one of the SSID's length passed in a scan or sched_scan request
is larger than 255, there will be an overflow in the u8 that is used
to store the length before checking. This causes the check to fail
and we overrun the buffer when copying the SSID.
Fix this by checking the nl80211 attribute length before copying it to
the struct.
This is a follow up for the previous commit
208c72f4fe, which didn't fix the problem
entirely.
Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel survey information will be empy for
disabled channels so simply discard those entries.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds dump support to testmode. The testmode
dump support in nl80211 requires using two of the
six cb->args, the rest can be used by the driver
to figure out where the dump position is at or to
store other data across invocations.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg