It's unreasonable to have CONFIG_ACPI for these in drivers, so add some
stub functions.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull an ACPI patch from Len Brown:
"It fixes a D3 issue new in 3.4-rc1."
By Lin Ming via Len Brown:
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
ACPI: Fix D3hot v D3cold confusion
Before this patch, ACPI_STATE_D3 incorrectly referenced D3hot
in some places, but D3cold in other places.
After this patch, ACPI_STATE_D3 always means ACPI_STATE_D3_COLD;
and all references to D3hot use ACPI_STATE_D3_HOT.
ACPI's _PR3 method is used to enter both D3hot and D3cold states.
What distinguishes D3hot from D3cold is the presence _PR3
(Power Resources for D3hot) If these resources are all ON,
then the state is D3hot. If _PR3 is not present,
or all _PR0 resources for the devices are OFF,
then the state is D3cold.
This patch applies after Linux-3.4-rc1.
A future syntax cleanup may remove ACPI_STATE_D3
to emphasize that it always means ACPI_STATE_D3_COLD.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull x86 fixes from H. Peter Anvin.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x32, siginfo: Provide proper overrides for x32 siginfo_t
asm-generic: Allow overriding clock_t and add attributes to siginfo_t
x32: Check __ILP32__ instead of __LP64__ for x32
x86, acpi: Call acpi_enter_sleep_state via an asmlinkage C function from assembler
ACPI: Convert wake_sleep_flags to a value instead of function
x86, apic: APIC code touches invalid MSR on P5 class machines
i387: ptrace breaks the lazy-fpu-restore logic
x86/platform: Remove incorrect error message in x86_default_fixup_cpu_id()
x86, efi: Add dedicated EFI stub entry point
x86/amd: Remove broken links from comment and kernel message
x86, microcode: Ensure that module is only loaded on supported AMD CPUs
x86, microcode: Fix sysfs warning during module unload on unsupported CPUs
With commit a2ef5c4fd4
"ACPI: Move module parameter gts and bfs to sleep.c" the wake_sleep_flags
is required when calling acpi_enter_sleep_state, which means
that if there are functions outside the sleep.c code they
can't get the wake_sleep_flags values.
This converts the function in to a exported value and converts
the module config operands to a function.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Lin Ming <ming.m.lin@intel.com>
[v2: Parameters can be turned on/off dynamically]
[v3: unsigned char -> u8]
[v4: val -> kp->arg]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/1335150198-21899-2-git-send-email-konrad.wilk@oracle.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This reverts commit cf450136bf.
It breaks reboot on at least one Thinkpad T43, as reported by Jörg Otte:
"On reboot it shuts down as normal.
The last lines displayed are:
>Unmounting temporary filesystems.. [OK]
>Deactivating swap... [OK]
>Unmounting local filesystems... [OK]
>Will now restart
> Restarting system
Then I hear it accessing the cd-drive, but then it's being stuck."
Jörg bisected the regression to this commit.
That commit fixes another machine (see
https://bugzilla.kernel.org/show_bug.cgi?id=11533
for details) that has a BIOS bug and doesn't support ACPI reset.
However, at least one of those other reporters no longer even has the
machine in question, and had a different workaround to begin with.
Besides, it clearly was a buggy BIOS. Let's not break the correct case
to fix that case.
Reported-and-bisected-by: Jörg Otte <jrg.otte@googlemail.com>
Cc: linux-acpi@vger.kernel.org
Cc: Len Brown <lenb@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 6fe0d06282.
Paul bisected this regression.
The conversion was done blindly and is wrong, as it does not provide a
primary handler to disable the level type irq on the device level.
Neither does it set the IRQF_ONESHOT flag which handles that at the irq
line level. This can't be done as the interrupt might be shared, though
we might extend the core to force it.
So an interrupt on this line will wake up the thread, but immediately
unmask the irq after that. Due to the interrupt being level type the
hardware interrupt is raised over and over and prevents the irq thread
from handling it. Fail.
request_irq() unfortunately does not refuse such a request and the patch
was obviously never tested with real interrupts.
Bisected-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ACPI & Power Management patches from Len Brown:
"Two fixes for cpuidle merge-window changes, plus a URL fix in
MAINTAINERS"
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
MAINTAINERS: Update git url for ACPI
cpuidle: Fix panic in CPU off-lining with no idle driver
ACPI processor: Use safe_halt() rather than halt() in acpi_idle_play_dead()
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ACPI code is shared by arch/x86 and arch/ia64. ia64 doesn't provide a plain
"halt()" function. Use safe_halt() instead.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Tested-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Pull ACPI & Power Management changes from Len Brown:
- ACPI 5.0 after-ripples, ACPICA/Linux divergence cleanup
- cpuidle evolving, more ARM use
- thermal sub-system evolving, ditto
- assorted other PM bits
Fix up conflicts in various cpuidle implementations due to ARM cpuidle
cleanups (ARM at91 self-refresh and cpu idle code rewritten into
"standby" in asm conflicting with the consolidation of cpuidle time
keeping), trivial SH include file context conflict and RCU tracing fixes
in generic code.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (77 commits)
ACPI throttling: fix endian bug in acpi_read_throttling_status()
Disable MCP limit exceeded messages from Intel IPS driver
ACPI video: Don't start video device until its associated input device has been allocated
ACPI video: Harden video bus adding.
ACPI: Add support for exposing BGRT data
ACPI: export acpi_kobj
ACPI: Fix logic for removing mappings in 'acpi_unmap'
CPER failed to handle generic error records with multiple sections
ACPI: Clean redundant codes in scan.c
ACPI: Fix unprotected smp_processor_id() in acpi_processor_cst_has_changed()
ACPI: consistently use should_use_kmap()
PNPACPI: Fix device ref leaking in acpi_pnp_match
ACPI: Fix use-after-free in acpi_map_lsapic
ACPI: processor_driver: add missing kfree
ACPI, APEI: Fix incorrect APEI register bit width check and usage
Update documentation for parameter *notrigger* in einj.txt
ACPI, APEI, EINJ, new parameter to control trigger action
ACPI, APEI, EINJ, limit the range of einj_param
ACPI, APEI, Fix ERST header length check
cpuidle: power_usage should be declared signed integer
...
Conflicts:
drivers/acpi/acpica/hwsleep.c
Text conflict between:
2feec47d4c
(ACPICA: ACPI 5: Support for new FADT SleepStatus, SleepControl registers)
which removed #include "actables.h"
and
09f98a825a
(x86, acpi, tboot: Have a ACPI os prepare sleep instead of calling tboot_sleep.)
which removed #include <linux/tboot.h>
The resolution is to remove them both.
Signed-off-by: Len Brown <len.brown@intel.com>
Conflicts:
drivers/acpi/sleep.c
This was a text conflict between
a2ef5c4fd4
(ACPI: Move module parameter gts and bfs to sleep.c)
which added #include <linux/module.h>
and
b24e509885
(ACPI, PCI: Move acpi_dev_run_wake() to ACPI core)
which added #include <linux/pm_runtime.h>
The resolution was to take them both.
Signed-off-by: Len Brown <len.brown@intel.com>
Conflicts:
drivers/acpi/apei/apei-base.c
This was a conflict between
15afae6046
(CPI, APEI: Fix incorrect APEI register bit width check and usage)
and
653f4b538f
(ACPICA: Expand OSL memory read/write interfaces to 64 bits)
The former changed a parameter in the call to acpi_os_read_memory64()
and the later replaced all calls to acpi_os_read_memory64()
with calls to acpi_os_read_memory().
Signed-off-by: Len Brown <len.brown@intel.com>
Using a u64 here creates an endian bug. We store a u32 number in the
top byte which is a larger number than intended on big endian systems.
There is no reason to use a 64 bit data type here, I guess it was just
an oversight.
I removed the initialization to zero as well. It's needed with a u64
but with a u32, the variable gets initialized properly inside the call
to acpi_os_read_port().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Quoth Dmitry Torokhov:
In addition to bus notifier we do install device notifier explicitly
so it might fire up early. The easiest fox would be to move
acpi_video_bus_start_devices() after input_allocate_device() but
before input_register_device() - unregistered input devices can handle
input_event() calls just fine.
May fix crashes reported in:
https://bugzilla.kernel.org/show_bug.cgi?id=40672
Signed-off-by: Igor Murzov <e-mail@date.by>
Signed-off-by: Len Brown <len.brown@intel.com>
It is always better to check return values, so add some new checks and
correct existing ones.
v2: Be consistent and don't mix errors from -E* and AE_* namespaces.
Signed-off-by: Igor Murzov <e-mail@date.by>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI 5.0 adds the BGRT, a table that contains a pointer to the firmware
boot splash and associated metadata. This simple driver exposes it via
/sys/firmware/acpi in order to allow bootsplash applications to draw their
splash around the firmware image and reduce the number of jarring graphical
transitions during boot.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Drivers may wish to add entries to /sys/firmware/acpi, so export acpi_kobj
in order to let them do that.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Make sure the removal of mappings uses the same logic that put the
mappings in place.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The function apei_estatus_print() and apei_estatus_check() forget to move ahead
the gdata pointer when dealing with multiple generic error data sections.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The acpi_processor_cst_has_changed() function is invoked from a
CPU_ONLINE or CPU_DEAD function, which might well execute on CPU 0
even though the CPU being hotplugged is some other CPU. In addition,
acpi_processor_cst_has_changed() invokes smp_processor_id() without
protection, resulting in splats when onlining CPUs.
This commit therefore changes the smp_processor_id() to pr->id, as is
used elsewhere in the code, for example, in acpi_processor_add().
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Tested-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
... so that acpi_unmap()'s behavior gets in sync with acpi_map()'s.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The function acpi_processor_add is stored in the ops.add field of a
acpi_driver structure. This function is then called in
acpi_bus_driver_init. On failure, this function clears the field
device->driver_data, but does not free its contents. Thus the free has to
be done by the add function. In acpi_processor_add, the corresponding
value is pr. This value is currently freed on failure before storing it in
device->driver_data, but not after. This free is added in the error
handling code at the end of the function. The per_cpu variable
processors is also cleared so that it does not refer to a dangling pointer.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The current code incorrectly assumes that
(1) the APEI register bit width is always 8, 16, 32, or 64 and
(2) the APEI register bit width is always equal to the APEI
register access width.
ERST serialization instructions entries such as:
[030h 0048 1] Action : 00 [Begin Write Operation]
[031h 0049 1] Instruction : 03 [Write Register Value]
[032h 0050 1] Flags (decoded below) : 01
Preserve Register Bits : 1
[033h 0051 1] Reserved : 00
[034h 0052 12] Register Region : [Generic Address Structure]
[034h 0052 1] Space ID : 00 [SystemMemory]
[035h 0053 1] Bit Width : 03
[036h 0054 1] Bit Offset : 00
[037h 0055 1] Encoded Access Width : 03 [DWord Access:32]
[038h 0056 8] Address : 000000007F2D7038
[040h 0064 8] Value : 0000000000000001
[048h 0072 8] Mask : 0000000000000007
break this assumption by yielding:
[Firmware Bug]: APEI: Invalid bit width in GAR [0x7f2d7038/3/0]
I have found no ACPI specification requirements corresponding
with the above assumptions. There is even a good example in
the Serialization Instruction Entries section (ACPI 4.0 section
17.4,1.2, ACPI 4.0a section 2.5.1.2, ACPI 5.0 section 18.5.1.2)
that mentions a serialization instruction with a bit range of
[6:2] which is 5 bits wide, _not_ 8, 16, 32, or 64 bits wide.
Compile and boot tested with 3.3.0-rc7 on a IBM HX5.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some APEI firmware implementation will access injected address
specified in param1 to trigger the error when injecting memory
error, which means if one SRAR error is injected, the crash
always happens because it is executed in kernel context. This
new parameter can disable trigger action and control is taken
over by the user. In this way, an SRAR error can happen in user
context instead of crashing the system. This function is highly
depended on BIOS implementation so please ensure you know the
BIOS trigger procedure before you enable this switch.
v2:
notrigger should be created together with param1/param2
Tested-by: Tony Luck <tony.luck@lintel.com>
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On the platforms with ACPI4.x support, parameter extension
is not always doable, which means only parameter extension
is enabled, einj_param can take effect.
v2->v1: stopping early in einj_get_parameter_address for einj_param
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes a trivial copy & paste error in ERST header length check.
It's just for future safety because sizeof(struct acpi_table_einj)
equals to sizeof(struct acpi_table_erst) with current ACPI5.0
specification. It applies to v3.3-rc6.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently when a CPU is off-lined it enters either MWAIT-based idle or,
if MWAIT is not desired or supported, HLT-based idle (which places the
processor in C1 state). This patch allows processors without MWAIT
support to stay in states deeper than C1.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_processor_install_hotplug_notify() registers processor objects to
receive ACPI CPU hotplug event notifications. This patch additionally
registers processor device objects (ACPI0007) to receive the notifications
as well.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Print physical address info in a style consistent with the %pR style used
elsewhere in the kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
An HP laptop (Pavilion G4-1016tx) has the following code in _TMP:
Store (\_SB.PCI0.LPCB.EC0.RTMP, Local0)
If (LGreaterEqual (Local0, S4TP))
{
Store (One, HTS4)
}
S4TP is initialised at 0 and not programmed further until either _HOT or
_CRT is called. If we evaluate _TMP before the trip points then HTS4 will
always be set, causing the firmware to generate a message on boot
complaining that the system shut down because of overheating. The simplest
solution is just to reverse the checking of trip points and _TMP in thermal
init.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_dev_run_wake() is a generic function which can be used by
other subsystem too. Rename it to acpi_pm_device_run_wake, to be
consistent with acpi_pm_device_sleep_wake.
Then move it to ACPI core.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Devices may share same list of power resources in _PR0, for example
Device(Dev0)
{
Name (_PR0, Package (0x01)
{
P0PR,
P1PR
})
}
Device(Dev1)
{
Name (_PR0, Package (0x01)
{
P0PR,
P1PR
}
}
Assume Dev0 and Dev1 were runtime suspended.
Then Dev0 is resumed first and it goes into D0 state.
But Dev1 is left in D0_Uninitialised state.
This is wrong. In this case, Dev1 must be resumed too.
In order to hand this case, each power resource maintains a list of
devices which relies on it.
When power resource is ON, it will check if the devices on its list
can be resumed. The device can only be resumed when all the power
resouces of its _PR0 are ON.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If a device has _PR3, it means the device supports D3_COLD.
Add the ability to validate and enter D3_COLD state in ACPI.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Repair a common problem with objects that are defined to return
a variable-length Package of sub-objects. If there is only one
sub-object, some BIOS code mistakenly simply declares the single
object instead of a Package with one sub-object. This function
attempts to repair this error by wrapping a Package object around
the original object, creating the correct and expected Package
with one sub-object.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some ACPI interrupt actions may need to wait, and it's easiest to
have a thread context for this. So turn the ACPI interrupt
into a threaded interrupt.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
WARN() is not supposed to have side effects, so move the request_regions
outside.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Pull x86 platform driver updates from Matthew Garrett:
"Some significant updates to samsung-laptop, additional hardware
support for Toshibas, misc updates to various hardware and a new
backlight driver for some Apple machines."
Fix up trivial conflicts: geode Geos update happening next to net5501
support, and MSIC thermal platform support added twice.
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (77 commits)
acer-wmi: add quirk table for video backlight vendor mode
drivers/platform/x86/amilo-rfkill.c::amilo_rfkill_probe() avoid NULL deref
samsung-laptop: unregister ACPI video module for some well known laptops
acer-wmi: No wifi rfkill on Sony machines
thinkpad-acpi: recognize Lenovo as version string in newer V-series BIOS
asus-wmi: don't update power and brightness when using scalar
eeepc-wmi: split et2012 specific hacks
eeepc-wmi: refine quirks handling
asus-nb-wmi: set panel_power correctly
asus-wmi: move WAPF variable into quirks_entry
asus-wmi: store backlight power status for AIO machine
asus-wmi: add scalar board brightness adj. support
samsung-laptop: cleanup return type: mode_t vs umode_t
drivers, samsung-laptop: fix usage of isalnum
drivers, samsung-laptop: fix initialization of sabi_data in sabi_set_commandb
asus-wmi: on/off bit is not set when reading the value
eeepc-wmi: add extra keymaps for EP121
asus-nb-wmi: ignore useless keys
acer-wmi: support Lenovo ideapad S205 Brazos wifi switch
acer-wmi: fix out of input parameter size when set
...
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
Move linux specific module parameter gts and bfs out of ACPICA core
code to sleep.c.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Enhanced the sleep/wake interfaces to optionally execute the
_GTS method (Going To Sleep), and the _BFS method (Back From
Sleep). Windows apparently does not execute these methods, and
therefore these methods are often untested. It has been seen on
some systems where the execution of these methods causes errors
and also prevents the machine from entering S5. It is therefore
suggested that host operating systems do not execute these methods
by default. In the future, perhaps these methods can be optionally
executed based on the age of the system and/or what is the newest
version of Windows that the BIOS asks for via _OSI.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On Intel CPUs the processor typically uses the highest frequency
set by any logical CPU. When the system overheats
Linux first forces the frequency to the lowest available one
to lower the temperature.
However this was done only per logical CPU, which means all
logical CPUs in a package would need to go through this before
the frequency is actually lowered.
Worse this delay actually prevents real throttling, because
the real throttle code only proceeds when the lowest frequency
is already reached.
So when a throttle event happens force the lowest frequency
for all CPUs in the package where it happened. The per CPU
state is now kept per package, not per logical CPU. An alternative
would be to do it per cpufreq unit, but since we want to bring
down the temperature of the complete chip it's better
to do it for all.
In principle it may even make sense to do it for all CPUs,
but I kept it on the package for now.
With this change the frequency is actually lowered, which
in terms also allows real throttling to proceed.
I also removed an unnecessary per cpu variable initialization.
v2: Fix package mapping
Cc: <stable@vger.kernel.org>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Many namespace node types must have an attached object. For
these node types, print a message about a missing object during
a namespace dump.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Change the returned exception code from AE_BAD_PARAMETER to the
more appropriate AE_BAD_PATHNAME, when the input pathname to
evaluate object is invalid.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>