Commit Graph

12 Commits

Author SHA1 Message Date
Thierry Reding 7e939de1b2 soc/tegra: fuse: Unify Tegra20 and Tegra30 drivers
Unifying the drivers makes it easier to restrict the legacy probing
paths to 32-bit ARM. This in turn will come in handy as support for
new 64-bit ARM SoCs is added.

Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-07-16 10:38:28 +02:00
Marc Zyngier 1a703bffd8 ARM: tegra: remove old LIC support
Now that all DTs have been updated, entierely drop support for
the non-DT code.

This is likely to break platforms that do not update their DT,
so print a warning at boot time.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088583-15097-7-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2015-03-15 00:40:52 +00:00
Stephen Warren 6dee8200b7 ARM: tegra: use section-sized static mappings for LPAE too
The static mappings for Tegra's PPSB and APB regions were sized at 1MB
in order to allow mapping via sections in order to avoid burning RAM for
PTEs. On LPAE, sections are 2MB, so the static mappings need to be
larger in order to gain the same benefit. Set IO_{PPSB,APB}_SIZE to
SECTION_SIZE so this adjusts automatically.

While we're fiddling with iomap.h, compress IO_{IRAM,CPU}_VIRT together
to save virtual address space in the vmalloc region; these two regions
are mapped using PTEs.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
2013-12-04 12:25:25 -07:00
Joseph Lo f0c4ac1329 ARM: tegra: add LP1 support code for Tegra124
The LP1 suspend procedure is the same with Tegra30 and Tegra114. Just
need to update the difference of the register address, then we can
continue to share the code.

Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2013-10-18 16:28:10 -06:00
Stephen Warren 4cf6791a60 ARM: tegra: remove much of iomap.h
iomap.h defines the base address of Tegra peripherals. Most of this
information comes from device tree now, and hence can be deleted.
Entries are kept for various system peripherals that low-level code
(such as initial boot, system suspend/resume, debug) still requires.

Removing the values removes the temptation for someone to use them.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2013-09-17 13:44:22 -06:00
Stephen Warren fddb770dbe ARM: tegra: move resume vector define to irammap.h
irammap.h's purpose is to define the layout/usage of IRAM. As such,
TEGRA_IRAM_CODE_AREA should have been added there rather than iomap.h.
Move the define, and rename it something more descriptive.

Cc: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2013-09-17 13:44:22 -06:00
Thierry Reding d1523b52bf PCI: tegra: Move PCIe driver to drivers/pci/host
Move the PCIe driver from arch/arm/mach-tegra into the drivers/pci/host
directory. The motivation is to collect various host controller drivers
in the same location in order to facilitate refactoring.

The Tegra PCIe driver has been largely rewritten, both in order to turn
it into a proper platform driver and to add MSI (based on code by
Krishna Kishore <kthota@nvidia.com>) as well as device tree support.

Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
[swarren, split DT changes into a separate patch in another branch]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2013-08-13 12:07:45 -06:00
Joseph Lo e9f624499c ARM: tegra: add LP1 suspend support for Tegra114
The LP1 suspend mode will power off the CPU, clock gated the PLLs and put
SDRAM to self-refresh mode. Any interrupt can wake up device from LP1. The
sequence when LP1 suspending:

* tunning off L1 data cache and the MMU
* storing some EMC registers, DPD (deep power down) status, clk source of
  mselect and SCLK burst policy
* putting SDRAM into self-refresh
* switching CPU to CLK_M (12MHz OSC)
* tunning off PLLM, PLLP, PLLA, PLLC and PLLX
* switching SCLK to CLK_S (32KHz OSC)
* shutting off the CPU rail

The sequence of LP1 resuming:

* re-enabling PLLM, PLLP, PLLA, PLLC and PLLX
* restoring the clk source of mselect and SCLK burst policy
* setting up CCLK burst policy to PLLX
* restoring DPD status and some EMC registers
* resuming SDRAM to normal mode
* jumping to the "tegra_resume" from PMC_SCRATCH41

Due to the SDRAM will be put into self-refresh mode, the low level
procedures of LP1 suspending and resuming should be copied to
TEGRA_IRAM_CODE_AREA (TEGRA_IRAM_BASE + SZ_4K) when suspending. Before
restoring the CPU context when resuming, the SDRAM needs to be switched
back to normal mode. And the PLLs need to be re-enabled, SCLK burst policy
be restored. Then jumping to "tegra_resume" that was expected to be stored
in PMC_SCRATCH41 to restore CPU context and back to kernel.

Based on the work by: Bo Yan <byan@nvidia.com>

Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2013-08-12 13:30:12 -06:00
Joseph Lo 5b795d051c ARM: tegra: add common resume handling code for LP1 resuming
Add support to the Tegra CPU reset vector to detect whether the CPU is
resuming from LP1 suspend state. If it is, branch to the LP1-specific
resume code.

When Tegra enters the LP1 suspend state, the SDRAM controller is placed
into a self-refresh state. For this reason, we must place the LP1 resume
code into IRAM, so that it is accessible before SDRAM access has been
re-enabled.

Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2013-08-12 12:22:38 -06:00
Venu Byravarasu 16a665f805 ARM: tegra: remove USB address related macros from iomap.h
USB register base address and sizes defined in iomap.h
are not used in any files other than board-dt-tegra20.c.
Hence removed those defines from header file and using
the absolute values in board files.

Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2013-01-28 11:20:04 -07:00
Stephen Warren adc1831588 ARM: tegra: simplify DEBUG_LL UART selection options
Delete CONFIG_TEGRA_DEBUG_UART_AUTO_SCRATCH; it's not useful any more:
* No upstream bootloader currently or will ever support this option.
* CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA is a much more direct alternative.

Merge the fixed and automatic UART selection menus into a single choice
for simplicity; now you either pick AUTO_ODMDATA or a single fixed UART,
rather than potentially having an AUTO option override whatever fixed
option was chosen.

Remove TEGRA_DEBUG_UART_NONE; if you don't want a Tegra DEBUG_LL UART,
simply don't turn on DEBUG_LL. NONE used to be the default option, so
pick AUTO_ODMDATA as the new default.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2012-11-16 12:22:17 -07:00
Stephen Warren 2be39c079d ARM: tegra: move iomap.h to mach-tegra
Nothing outside mach-tegra uses this file, so there's no need for it to
be in <mach/>.

Since uncompress.h and debug-macro.S remain in include/mach, they need
to include "../../iomap.h" becaue of this change. uncompress.h will soon
be deleted in later multi-platform/single-zImage patches. debug-macro.S
will need to continue to include this header using an explicit relative
path, to avoid duplicating the physical->virtual address mapping that
iomap.h dictates.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2012-11-05 11:36:06 -07:00