OOS_HANDED_TO_NETWORK should not be grouped with the various
*_CANCELED/*_FAILED cases.
Also, not only clear the RQ_NET_QUEUED flag, but also mark it RQ_NET_DONE,
so it can be distinguished from a local-only request even after that.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We used to have a barrier implementation where barrier_nr 0 was
reserved. That is long gone. Just use the full sequence space.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We assumed only bios with bi_idx == 0 would end up
in drbd_make_request().
That is wrong.
At least device mapper, in __clone_and_map(), may submit
clones only covering a partial bio, but sharing
the original bvec, by adjusting bi_idx and relevant
other bio members of the clone.
We used __bio_for_each_segment() in various places,
even though that is documented as
* drivers should not use the __ version unless they _really_ want to
* run through the entire bio and not just pending pieces
Impact: we would send the full bio bvec, even for the clone
with bi_idx > 0, which will cause data corruption on the
peer (because we submit wrong data at the clone offset),
and will cause a DRBD protocol error, disconnect/reconnect
and resync (thus fixing the corruption),
because the next package header would be expected right
in the middle of the sent data, causing DRBD magic mismatch.
Fix: drop the assert, and use bio_for_each_segment()
instead of the __ version.
Conflicts:
drbd/drbd_tracing.c
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If a SyncTarget node gets a P_RS_DATA_REPLY before a P_DATA packet
for the same sector, it simply submits these two IO requests.
This is be possible because on the SyncSource node, the data of the
P_RS_DATA_REPLY packet was read from disk. Immediately after that a
write request from upper layers came in.
The disk scheduler or even the "hardware" queues on the disk drive might
reorder these writes.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When we have a write request and a state change C_WF_BITMAP_S -> C_SYNC_SOURCE
at the same time, and it happens that the line
remote = remote && drbd_should_do_remote(s);
stills sees C_WF_BITMAP_S, and
send_oos = rw == WRITE && drbd_should_send_oos(s);
already sees C_SYNC_SOURCE both are 0.
This causes the write to not be mirrored, but marked as out-of-sync on the
Sync_Source node.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Without this, iostat frequently sees bogus svctime and >= 100% "utilization".
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
drbd_accept was modelled after kernel_accept
with drbd commit 53eb779 in July 2008.
Only, kernel_accept was then broken, and only fixed later
with kernel commit 1b08534e in Dec 2008:
net: Fix module refcount leak in kernel_accept()
Impact: protocol families provided as modules, e.g. ipv6 or ib_sdp,
would soon have their reference count become negative, preventing
them from being unloaded (likely), or worse, hit zero without actually
being unused, allowing them to be unloaded while still in use (unlikely,
but if triggered, causing a kernel crash).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If the backing device is already frozen during attach, we failed
to recognize that. The current disk-timeout code works on top
of the drbd_request objects. During attach we do not allow IO
and therefore never generate a drbd_request object but block
before that in drbd_make_request().
This patch adds the timeout to all drbd_md_sync_page_io().
Before this patch we used to go from D_ATTACHING directly
to D_DISKLESS if IO failed during attach. We can no longer
do this since we have to stay in D_FAILED until all IO
ops issued to the backing device returned.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
I.e. in C_WF_REPORT_PARAMS or in C_WF_CONNECTION.
Sending may already work in these cstates, but the peer still expects
the HandShake / ConnectionFeatures packet.
Actually triggered by the Testuite on kugel.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If the asender thread, or request_timer_fn(), or some other part of
the code, decided to drop the connection (because of timeout or other),
but the receiver just now was processing a P_STATE packet, there was a
chance that receive_state() would do a hard state change
"re-establishing" an already failed connection without additional handshake.
Log excerpt:
Remote failed to finish a request within ko-count * timeout
peer( Secondary -> Unknown ) conn( Connected -> Timeout ) pdsk( UpToDate -> DUnknown )
asender terminated
...
peer( Unknown -> Secondary ) conn( Timeout -> Connected ) pdsk( DUnknown -> UpToDate ) peer_isp( 0 -> 1 )
...
Connection closed
peer( Secondary -> Unknown ) conn( Connected -> Unconnected ) pdsk( UpToDate -> DUnknown ) peer_isp( 1 -> 0 )
receiver terminated
Impact:
while the connection state is erroneously "Connected",
requests may be queued and even sent,
which would never be acknowledged,
and may have been missed by the cleanup.
These requests would never be completed.
The next drbd_suspend_io() will then lock up,
waiting forever for these requests to complete.
Fixed in several code paths:
Make sure the connection state is NetworkFailure or worse
before starting the cleanup in drbd_disconnect().
This should make sure the cleanup won't miss any requests.
Disallow receive_state() to "upgrade" the connection state
from an error state. This will make sure the "illegal" state
transition won't happen.
For all connection failure states,
relax the safe-guard in sanitize_state() again
to silently mask out those state changes
(e.g. Timeout -> Connected becomes Timeout -> Timeout).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
drbd_try_clear_on_disk_bm() has a sanity check for the number of blocks
left to be resynced (rs_left) in the current resync extent.
If it detects a mismatch, it complains, and forces a disconnect using
drbd_force_state(mdev, NS(conn, C_DISCONNECTING));
Unfortunately, this may be called while holding the req_lock,
and drbd_force_state() want's to aquire that lock itself. Deadlock.
Don't force a disconnect, but fix up rs_left by recounting and
reassigning the number of dirty blocks in that extent.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This bug might have caused troubles if disk-barriers and the ahead-behind
more are enabled at the same time.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
DRBD state changes schedule after_state_ch() actions to a worker thread,
which decides on the old and new states of that change, whether to send
an informational state update packet (P_STATE) to the peer.
If it decides to drbd_send_state(), it would however always send the
_curent_ state, which, if a second state change happens before the
after_state_ch() of the first ran, may "fast-forward" the peer's view
about this node. In most cases that is harmless, but sometimes this can
confuse DRBD, for example into not actually starting a necessary resync
if you do a very tight detach/attach loop on a Connected Secondary.
Fix this by always sending the "new" state of the respective state
transition which scheduled this after_state_ch() work.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When detaching, even cleanly detaching due to administrator request,
we always go through D_FAILED before we become D_DISKLESS.
Don't let that state change race with an in-flight meta data IO,
or that one might think it actually experienced an IO error.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
drbd_state_lock() is only there to serialize cluster wide state
changes. Testing the local disk state needs to happen while
holding the global_state_lock.
Otherwise you might see something like this (Oct 6 on kugel)
14:20:24 drbd0: conn( WFSyncUUID -> Connected ) disk( Inconsistent -> Failed )
14:20:24 drbd0: helper command: /sbin/drbdadm before-resync-target minor-0 exit code 0 (0x0)
14:20:24 drbd0: conn( Connected -> SyncTarget ) disk( Failed -> Inconsistent )
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We have one pre-allocated page to do certain synchronous meta data IO with,
using it is serialized like so:
drbd_md_get_buffer();
drbd_md_sync_page_io();
drbd_md_sync_page_io();
...
drbd_md_put_buffer();
In drbd_md_sync_page_io() there is an
ASSERT(atomic_read(&mdev->md_io_in_use) == 1);
We want to be able to timeout on unresponsive lower level devices, so we
can "detach" in that case. Inside drbd_md_sync_page_io() we grab an extra
reference, to not have a dangling pointer in case a delayed IO eventually
does still complete, even after we "detached" already.
We need to put the extra reference before we signal completion from the
completion handler, or the second drbd_md_sync_page_io() above may
trigger the assert (reference count still 2).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
With sync-after dependencies, given "lucky" timing of pause/unpause
events, and the end of an empty (0 bits set) resync was sometimes not
detected on the SyncTarget, leading to a "stalled" SyncSource state.
Fixed this by expecting not only "Inconsistent -> UpToDate" but also
"Consistent -> UpToDate" transitions for the peer disk state
to end a resync.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we get into the C_BROKEN_PIPE cstate once, the state engine set the
thi->t_state of the receiver thread to restarting. But with the while loop
in drbdd_init() a new connection gets established. After the call into
drbdd() returns immediately since the thi->t_state is not RUNNING. The
restart of drbd_init() then resets thi->t_state to RUNNING.
I.e. after entering C_BROKEN_PIPE once, the next successful established
connection gets wasted.
The two parts of the fix:
* Do not cause the thread to restart if we detect the issue
with the sockets while we are in C_WF_CONNECTION.
* Make sure that all actions that would have set us to C_BROKEN_PIPE
happen before the state change to C_WF_REPORT_PARAMS.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
...when the peer has inconsistent data. In that case we failed to
clear the susp_nod flag. When the local disk was attached again
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Now, the new edition of the clause only fires if a diskless
peer gets promoted.
This is a fixup for "drbd: Delayed creation of current-UUID".
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Bitmap IO may happend in the context of an application write,
in the generic block IO path. We need to use GFP_NOIO.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When the disk-timeout is active, and it expires for a single request,
we consider the local disk as D_FAILED. Note: With this change,
I made both timeout based state transitions HARD state transitions.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The last bunch of commits prepared the 'detach from tar pit' feature.
With that we can be for long time in disk state FAILED. We need
to accept new IO requests during that time.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The new function drbd_md_get_buffer() aborts waiting for the buffer
in case the disk failes in the meantime.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Regression introduced with 8.3.11 commit:
drbd: Take a more conservative approach when deciding max_bio_size
Never ever tell an older drbd, that we support more than 32KiB
in a single data request (packet).
Never believe an older drbd, that is supports more than 32KiB
in a single data request (packet)
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The reason for this change is that, with when doing
'drbdadm invalidate' on a disconnected resource caused
an "implicitly set pdsk from UpToDate to DUnknown" message,
which was missleading.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Fix warnings of the following nature in the drbd header:
In file included from drivers/block/drbd/drbd_bitmap.c:32:
drivers/block/drbd/drbd_int.h: In function 'drbd_get_syncer_progress':
drivers/block/drbd/drbd_int.h:2234: warning: comparison is always false due to limited range of data
where mdev->rs_total (an unsigned long) is being compared to 1ULL << 32, which
is always false on a 32-bit machine.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
It is not "to small", but "too small".
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
For large resync rates, seq_printf_with_thousands_grouping()
accidentally only produced Y,000,00Y, instead of the real numbers.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This was an ill-conceived feature that has been removed from Ceph. Do
this gracefully:
- reject attempts to specify a preferred_osd via the ioctl
- stop exposing this information via virtual xattrs
- always fill in -1 for requests, in case we talk to an older server
- don't calculate preferred_osd placements/pgids
Reviewed-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Fix merge between commit 3adadc08cc ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d ("net ax25: Simplify and
cleanup the ax25 sysctl handling")
The former moved around the sysctl register/unregister calls, the
later simply removed them.
With help from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Name them in a "backward compatible" manner, i.e. reuse or not
are still 1 and 0 respectively. The reuse value of 2 means that
the socket with it will forcibly reuse everyone else's port.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* mechanism to work with misconfigured backends (where they are
advertised but in reality don't exist).
* two tiny compile warning fixes.
* proper error handling in gnttab_resume
* Not using VM_PFNMAP anymore to allow backends in the same domain.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPkYeqAAoJEFjIrFwIi8fJEXIIAI+PYLNMcHTc4bxa6pErpKaS
rq5eCXL9+EaZOwTUqHRJjfrjnlAc+BWO8lN0H41oRQWFYh14hgfUVJ+ziEujb1kw
N1eTMVHnH/XRJV6rIFX+TiBasnyoMmNfWEAb45UL1nEUTMPL1Jv7AiRY/GxUlHyg
M+uFG52KP3ytXxcIiGW6pYEqJd6UgWrqnclaeg5TR5zvDlWfJbUIBEMQ/PyV0WSS
4e7biiwi4XPWT2f1qewOmI+3r68CltU3GAs1XxjcSX+bYYuh00UtY39AsBWo2N8I
1VORuq0QPs+GB22r3e47IqBcjXkBGRIf6w1e/5a6WLiq7TqVq4bYgCGUmWT8V7o=
=olCU
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.4-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen fixes from Konrad Rzeszutek Wilk:
- mechanism to work with misconfigured backends (where they are
advertised but in reality don't exist).
- two tiny compile warning fixes.
- proper error handling in gnttab_resume
- Not using VM_PFNMAP anymore to allow backends in the same domain.
* tag 'stable/for-linus-3.4-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
Revert "xen/p2m: m2p_find_override: use list_for_each_entry_safe"
xen/resume: Fix compile warnings.
xen/xenbus: Add quirk to deal with misconfigured backends.
xen/blkback: Fix warning error.
xen/p2m: m2p_find_override: use list_for_each_entry_safe
xen/gntdev: do not set VM_PFNMAP
xen/grant-table: add error-handling code on failure of gnttab_resume
drivers/block/xen-blkback/xenbus.c: In function 'xen_blkbk_discard':
drivers/block/xen-blkback/xenbus.c:419:4: warning: passing argument 1 of 'dev_warn' makes pointer from integer without a cast
+[enabled by default]
include/linux/device.h:894:5: note: expected 'const struct device *' but argument is of type 'long int'
It is unclear how that mistake made it in. It surely is wrong.
Acked-by: Jens Axboe <axboe@kernel.dk>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Here are some virtio fixes for 3.4:
a test build fix, a patch by Ren fixing naming for systems with a massive
number of virtio blk devices, and balloon fixes for powerpc
by David Gibson.
There was some discussion about Ren's patch for virtio disc naming: some people
wanted to move the legacy name mangling function to the block core. But
there's no concensus on that yet, and we can always deduplicate later.
Added comments in the hope that this will stop people from
copying this legacy naming scheme into future drivers.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPio1GAAoJECgfDbjSjVRpGDAH/3C/bXm9mriuNauRHwktHgJe
gmh2BfUgnxly6vheuz0Fv61lTe6V8kekHVolbUYwAUgXeWEKK1C59xehrMGRIPDG
1XUiti50U3P+skhIfrbkS5nZ7L+5Hk0ToQ6dd9v0BM2GxDOvgwidlY1bZe+wJEZf
Lvl6w/djBCr1e3k4qfRnpTcdJJ4FnOjGbikLQhSTGfUXeNo6uWS1hljYWnAhzFkd
1xU8h5PP0TDR0nYb80CeB+9Lxw0w4qyNPJIBhNN6ucB/1U6R+55HpEpmrLUkn910
sEFEFsc0cRVWr8FiOTlmzxLHnwTc8AY/Bsp9TMSmnTRu3ZQcoQMTQQCczRj04xI=
=VmpJ
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael S. Tsirkin:
"Here are some virtio fixes for 3.4: a test build fix, a patch by Ren
fixing naming for systems with a massive number of virtio blk devices,
and balloon fixes for powerpc by David Gibson.
There was some discussion about Ren's patch for virtio disc naming:
some people wanted to move the legacy name mangling function to the
block core. But there's no concensus on that yet, and we can always
deduplicate later. Added comments in the hope that this will stop
people from copying this legacy naming scheme into future drivers."
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_balloon: fix handling of PAGE_SIZE != 4k
virtio_balloon: Fix endian bug
virtio_blk: helper function to format disk names
tools/virtio: fix up vhost/test module build
Pull block driver bits from Jens Axboe:
- A series of fixes for mtip32xx. Most from Asai at Micron, but also
one from Greg, getting rid of the dependency on PCIE_HOTPLUG.
- A few bug fixes for xen-blkfront, and blkback.
- A virtio-blk fix for Vivek, making resize actually work.
- Two fixes from Stephen, making larger transfers possible on cciss.
This is needed for tape drive support.
* 'for-3.4/drivers' of git://git.kernel.dk/linux-block:
block: mtip32xx: remove HOTPLUG_PCI_PCIE dependancy
mtip32xx: dump tagmap on failure
mtip32xx: fix handling of commands in various scenarios
mtip32xx: Shorten macro names
mtip32xx: misc changes
mtip32xx: Add new sysfs entry 'status'
mtip32xx: make setting comp_time as common
mtip32xx: Add new bitwise flag 'dd_flag'
mtip32xx: fix error handling in mtip_init()
virtio-blk: Call revalidate_disk() upon online disk resize
xen/blkback: Make optional features be really optional.
xen/blkback: Squash the discard support for 'file' and 'phy' type.
mtip32xx: fix incorrect value set for drv_cleanup_done, and re-initialize and start port in mtip_restart_port()
cciss: Fix scsi tape io with more than 255 scatter gather elements
cciss: Initialize scsi host max_sectors for tape drive support
xen-blkfront: make blkif_io_lock spinlock per-device
xen/blkfront: don't put bdev right after getting it
xen-blkfront: use bitmap_set() and bitmap_clear()
xen/blkback: Enable blkback on HVM guests
xen/blkback: use grant-table.c hypercall wrappers
The current virtio block's naming algorithm just supports 18278
(26^3 + 26^2 + 26) disks. If there are more virtio blocks,
there will be disks with the same name.
Based on commit 3e1a7ff8a0, add
a function "virtblk_name_format()" for virtio block to support mass
of disks naming.
Notes:
- Our naming scheme is ugly. We are stuck with it
for virtio but don't use it for any new driver:
new drivers should name their devices PREFIX%d
where the sequence number can be allocated by ida
- sd_format_disk_name has exactly the same logic.
Moving it to a central place was deferred over worries
that this will make people keep using the legacy naming
in new drivers.
We kept code idential in case someone wants to deduplicate later.
Signed-off-by: Ren Mingxin <renmx@cn.fujitsu.com>
Acked-by: Asias He <asias@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This removes the HOTPLUG_PCI_PCIE dependency on the driver and makes it
depend on PCI.
Cc: Sam Bradshaw <sbradshaw@micron.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Dump tagmap on failure, instead of individual tags.
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* If a ncq command time out and a non-ncq command is active, skip restart port
* Queue(pause) ncq commands during operations spanning more than one non-ncq commands - secure erase, download microcode
* When a non-ncq command is active, allow incoming non-ncq commands to wait instead of failing back
* Changed timeout for download microcode and smart commands
* If the device in write protect mode, fail all writes (do not send to device)
* Set maximum retries to 2
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Shortened macros used to represent mtip_port->flags and dd->dd_flag
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* Handle the interrupt completion of polled internal commands
* Do not check remove pending flag for standby command
* On rebuild failure,
- set corresponding bit dd_flag
- do not send standby command
* Free ida index in remove path
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* Add support for detecting the following device status
- write protect
- over temp (thermal shutdown)
* Add new sysfs entry 'status', possible values - online, write_protect, thermal_shutdown
* Add new file 'sysfs-block-rssd' to document ABI (Reported-by: Greg Kroah-Hartman)
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Moved setting completion time into mtip_issue_ncq_command()
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* Merged the following flags into one variable 'dd_flag':
* drv_cleanup_done
* resumeflag
* Added the following flags into 'dd_flag'
* remove pending
* init done
* Removed 'ftlrebuildflag' (similar flag is already part of mti_port->flags)
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* one is a workaround that will be removed in v3.5 with proper fix in the tip/x86 tree,
* the other is to fix drivers to load on PV (a previous patch made them only
load in PVonHVM mode).
The rest are just minor fixes in the various drivers and some cleanup in the
core code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPfyVUAAoJEFjIrFwIi8fJUjUH/jbY5JavRqSlNELZW2A4Ta76
8p00LqLHw/C56iHZcWKke8mqtWNb+ZfcQt7ZYcxDIYa4QWBL28x0OLAO2tOBIt37
ZjYESWSdFJaJvmpADluWtFyGyZ9TYJllDTBm/jWj1ZtKSZvR1YkhuMXCS0f4AmGQ
xFzSWJZUDdiOAqpN+VQD8wP00gfR8knQLg16XE2fvFdQo4XwpCtqLfHV/5pMMGdy
Cs/ep6rq/7cdv/nshKOcBnw7RW8l3Xoi/28ht8k3DvAQ2VtFq1Tugv2G9pcCHwQG
DIBkB3SOU6/v6P5at5+egKS5xR1fJetCWlkMd8kkbcdz2NPI4UDMkvOW6Q8yQls=
=6Ve+
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen fixes from Konrad Rzeszutek Wilk:
"Two fixes for regressions:
* one is a workaround that will be removed in v3.5 with proper fix in
the tip/x86 tree,
* the other is to fix drivers to load on PV (a previous patch made
them only load in PVonHVM mode).
The rest are just minor fixes in the various drivers and some cleanup
in the core code."
* tag 'stable/for-linus-3.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pcifront: avoid pci_frontend_enable_msix() falsely returning success
xen/pciback: fix XEN_PCI_OP_enable_msix result
xen/smp: Remove unnecessary call to smp_processor_id()
xen/x86: Workaround 'x86/ioapic: Add register level checks to detect bogus io-apic entries'
xen: only check xen_platform_pci_unplug if hvm
commit b9136d207f08
xen: initialize platform-pci even if xen_emul_unplug=never
breaks blkfront/netfront by not loading them because of
xen_platform_pci_unplug=0 and it is never set for PV guest.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
A recent change made changes to the rbd_client_list be protected by
a spinlock. Unfortunately in rbd_put_client(), the lock is taken
before possibly dropping the last reference to an rbd_client, and on
the last reference that eventually calls flush_workqueue() which can
sleep.
The problem was flagged by a debug spinlock warning:
BUG: spinlock wrong CPU on CPU#3, rbd/27814
The solution is to move the spinlock acquisition and release inside
rbd_client_release(), which is the spot where it's really needed for
protecting the removal of the rbd_client from the client list.
Signed-off-by: Alex Elder <elder@dreamhost.com>
Reviewed-by: Sage Weil <sage@newdream.net>
The X86_32-only disable_hlt/enable_hlt mechanism was used by the
32-bit floppy driver. Its effect was to replace the use of the
HLT instruction inside default_idle() with cpu_relax() - essentially
it turned off the use of HLT.
This workaround was commented in the code as:
"disable hlt during certain critical i/o operations"
"This halt magic was a workaround for ancient floppy DMA
wreckage. It should be safe to remove."
H. Peter Anvin additionally adds:
"To the best of my knowledge, no-hlt only existed because of
flaky power distributions on 386/486 systems which were sold to
run DOS. Since DOS did no power management of any kind,
including HLT, the power draw was fairly uniform; when exposed
to the much hhigher noise levels you got when Linux used HLT
caused some of these systems to fail.
They were by far in the minority even back then."
Alan Cox further says:
"Also for the Cyrix 5510 which tended to go castors up if a HLT
occurred during a DMA cycle and on a few other boxes HLT during
DMA tended to go astray.
Do we care ? I doubt it. The 5510 was pretty obscure, the 5520
fixed it, the 5530 is probably the oldest still in any kind of
use."
So, let's finally drop this.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Stephen Hemminger <shemminger@vyatta.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/n/tip-3rhk9bzf0x9rljkv488tloib@git.kernel.org
[ If anyone cares then alternative instruction patching could be
used to replace HLT with a one-byte NOP instruction. Much simpler. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If a virtio disk is open in guest and a disk resize operation is done,
(virsh blockresize), new size is not visible to tools like "fdisk -l".
This seems to be happening as we update only part->nr_sects and not
bdev->bd_inode size.
Call revalidate_disk() which should take care of it. I tested growing disk
size of already open disk and it works for me.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Merge third batch of patches from Andrew Morton:
- Some MM stragglers
- core SMP library cleanups (on_each_cpu_mask)
- Some IPI optimisations
- kexec
- kdump
- IPMI
- the radix-tree iterator work
- various other misc bits.
"That'll do for -rc1. I still have ~10 patches for 3.4, will send
those along when they've baked a little more."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (35 commits)
backlight: fix typo in tosa_lcd.c
crc32: add help text for the algorithm select option
mm: move hugepage test examples to tools/testing/selftests/vm
mm: move slabinfo.c to tools/vm
mm: move page-types.c from Documentation to tools/vm
selftests/Makefile: make `run_tests' depend on `all'
selftests: launch individual selftests from the main Makefile
radix-tree: use iterators in find_get_pages* functions
radix-tree: rewrite gang lookup using iterator
radix-tree: introduce bit-optimized iterator
fs/proc/namespaces.c: prevent crash when ns_entries[] is empty
nbd: rename the nbd_device variable from lo to nbd
pidns: add reboot_pid_ns() to handle the reboot syscall
sysctl: use bitmap library functions
ipmi: use locks on watchdog timeout set on reboot
ipmi: simplify locking
ipmi: fix message handling during panics
ipmi: use a tasklet for handling received messages
ipmi: increase KCS timeouts
ipmi: decrease the IPMI message transaction time in interrupt mode
...
rename the nbd_device variable from "lo" to "nbd", since "lo" is just a name
copied from loop.c.
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Pull a few more things for powerpc by Benjamin Herrenschmidt:
- Anton's did some recent improvements to EPOW event reporting on
pSeries (power supply failures and such). The patches are self
contained enough and replace really nasty code so I felt it should
still go in
- I did the vio driver registration change Greg requested, I don't see
the point of leaving that til the next merge window
- The remaining EEH changes I said were still pending to get rid of the
EEH references from the generic struct device_node
- A few more iSeries removal bits
- A perf bug fix on 970
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/perf: Fix instruction address sampling on 970 and Power4
powerpc+sparc/vio: Modernize driver registration
powerpc: Random little legacy iSeries removal tidy ups
powerpc: Remove NO_IRQ_IGNORE
powerpc/pseries: Cut down on enthusiastic use of defines in RAS code
powerpc/pseries: Clean up ras_error_interrupt code
powerpc/pseries: Remove RTAS_POWERMGM_EVENTS
powerpc/pseries: Use rtas_get_sensor in RAS code
powerpc/pseries: Parse and handle EPOW interrupts
powerpc: Make function that parses RTAS error logs global
powerpc/eeh: Retrieve PHB from global list
powerpc/eeh: Remove eeh information from pci_dn
powerpc/eeh: Remove eeh device from OF node
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
Pull Ceph updates for 3.4-rc1 from Sage Weil:
"Alex has been busy. There are a range of rbd and libceph cleanups,
especially surrounding device setup and teardown, and a few critical
fixes in that code. There are more cleanups in the messenger code,
virtual xattrs, a fix for CRC calculation/checks, and lots of other
miscellaneous stuff.
There's a patch from Amon Ott to make inos behave a bit better on
32-bit boxes, some decode check fixes from Xi Wang, and network
throttling fix from Jim Schutt, and a couple RBD fixes from Josh
Durgin.
No new functionality, just a lot of cleanup and bug fixing."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (65 commits)
rbd: move snap_rwsem to the device, rename to header_rwsem
ceph: fix three bugs, two in ceph_vxattrcb_file_layout()
libceph: isolate kmap() call in write_partial_msg_pages()
libceph: rename "page_shift" variable to something sensible
libceph: get rid of zero_page_address
libceph: only call kernel_sendpage() via helper
libceph: use kernel_sendpage() for sending zeroes
libceph: fix inverted crc option logic
libceph: some simple changes
libceph: small refactor in write_partial_kvec()
libceph: do crc calculations outside loop
libceph: separate CRC calculation from byte swapping
libceph: use "do" in CRC-related Boolean variables
ceph: ensure Boolean options support both senses
libceph: a few small changes
libceph: make ceph_tcp_connect() return int
libceph: encapsulate some messenger cleanup code
libceph: make ceph_msgr_wq private
libceph: encapsulate connection kvec operations
libceph: move prepare_write_banner()
...
This makes vio_register_driver() get the module owner & name at compile
time like PCI drivers do, and adds a name pointer directly in struct
vio_driver to avoid having to explicitly initialize the embedded
struct device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David S. Miller <davem@davemloft.net>
Konrad writes:
I've two small fixes for the xen-blkback - and I think one more will show up
eventually (a partial revert), but not sure when. So in the spirit of keeping
the patches flowing, please git pull the following branch.
* Add fast-EOI acking of interrupts (clear a bit instead of hypercall)
And bug-fixes:
* Fix CPU bring-up code missing a call to notify other subsystems.
* Fix reading /sys/hypervisor even if PVonHVM drivers are not loaded.
* In Xen ACPI processor driver: remove too verbose WARN messages, fix up
the Kconfig dependency to be a module by default, and add dependency on
CPU_FREQ.
* Disable CPU frequency drivers from loading when booting under Xen
(as we want the Xen ACPI processor to be used instead).
* Cleanups in tmem code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPbc3DAAoJEFjIrFwIi8fJTQkIAMnH2fPhcHAb4mNaz+3gdmsZ
Flo6V1gMBcO8xKZlUkFgKKPYoOm7lLmvoceXLVSH5oOKSnSJo1zSinzKmcdJQo/D
kPo4/EguNwtzcAcQh2dmT6/IM9O3ihMKUli7Oajif9PLCFFFqTaG3Y3YNBo/rxTY
D3HAnJrIfmIyG0NpLnaFCWhCzUvcB4M7ysutECqcF8l5gnbHxRVeCKD0blM+n9GH
Wyum00dQCwo6h6wTduhPOAxHAM4rncyR3heOB2vDxq9YJHSUhhcva5QCgQ+tdUVt
6U2TQT1L2Px8iXXzr2w9YBpepOVajZReoKhajLjJ5VbkpBZFz5dVNfJ8LpF8RV8=
=z8IB
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.4-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull more xen updates from Konrad Rzeszutek Wilk:
"One tiny feature that accidentally got lost in the initial git pull:
* Add fast-EOI acking of interrupts (clear a bit instead of
hypercall)
And bug-fixes:
* Fix CPU bring-up code missing a call to notify other subsystems.
* Fix reading /sys/hypervisor even if PVonHVM drivers are not loaded.
* In Xen ACPI processor driver: remove too verbose WARN messages, fix
up the Kconfig dependency to be a module by default, and add
dependency on CPU_FREQ.
* Disable CPU frequency drivers from loading when booting under Xen
(as we want the Xen ACPI processor to be used instead).
* Cleanups in tmem code."
* tag 'stable/for-linus-3.4-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/acpi: Fix Kconfig dependency on CPU_FREQ
xen: initialize platform-pci even if xen_emul_unplug=never
xen/smp: Fix bringup bug in AP code.
xen/acpi: Remove the WARN's as they just create noise.
xen/tmem: cleanup
xen: support pirq_eoi_map
xen/acpi-processor: Do not depend on CPU frequency scaling drivers.
xen/cpufreq: Disable the cpu frequency scaling drivers from loading.
provide disable_cpufreq() function to disable the API.
They were using the xenbus_dev_fatal() function which would
change the state of the connection immediately. Which is not
what we want when we advertise optional features.
So make 'feature-discard','feature-barrier','feature-flush-cache'
optional.
Suggested-by: Jan Beulich <JBeulich@suse.com>
[v1: Made the discard function void and static]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The only reason for the distinction was for the special case of
'file' (which is assumed to be loopback device), was to reach inside
the loopback device, find the underlaying file, and call fallocate on it.
Fortunately "xen-blkback: convert hole punching to discard request on
loop devices" removes that use-case and we now based the discard
support based on blk_queue_discard(q) and extract all appropriate
parameters from the 'struct request_queue'.
CC: Li Dongyang <lidongyang@novell.com>
Acked-by: Jan Beulich <JBeulich@suse.com>
[v1: Dropping pointless initializer and keeping blank line]
[v2: Remove the kfree as it is not used anymore]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This patch includes two changes:
* fix incorrect value set for drv_cleanup_done
* re-initialize and start port in mtip_restart_port()
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Sam Bradshaw <sbradshaw@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The total number of scatter gather elements in the CISS command
used by the scsi tape code was being cast to a u8, which can hold
at most 255 scatter gather elements. It should have been cast to
a u16. Without this patch the command gets rejected by the controller
since the total scatter gather count did not add up to the right
value resulting in an i/o error.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The default is too small (1024 blocks), use h->cciss_max_sectors (8192 blocks)
Without this change, if you try to set the block size of a tape drive above
512*1024, via "mt -f /dev/st0 setblk nnn" where nnn is greater than 524288,
it won't work right.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A new temporary header is allocated each time the header changes, but
only the changed properties are copied over. We don't need a new
semaphore for each header update.
This addresses http://tracker.newdream.net/issues/2174
Signed-off-by: Josh Durgin <josh.durgin@dreamhost.com>
Reviewed-by: Alex Elder <elder@dreamhost.com>
Currently an rbd device's id is released when it is removed, but it
is done before the code is run to clean up sysfs-related files (such
as /sys/bus/rbd/devices/1).
It's possible that an rbd is still in use after the rbd_remove()
call has been made. It's essentially the same as an active inode
that stays around after it has been removed--until its final close
operation. This means that the id shows up as free for reuse at a
time it should not be.
The effect of this was seen by Jens Rehpoehler, who:
- had a filesystem mounted on an rbd device
- unmapped that filesystem (without unmounting)
- found that the mount still worked properly
- but hit a panic when he attempted to re-map a new rbd device
This re-map attempt found the previously-unmapped id available.
The subsequent attempt to reuse it was met with a panic while
attempting to (re-)install the sysfs entry for the new mapped
device.
Fix this by holding off "putting" the rbd id, until the rbd_device
release function is called--when the last reference is finally
dropped.
Note: This fixes: http://tracker.newdream.net/issues/1907
Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
Here is another set of small code tidy-ups:
- Define SECTOR_SHIFT and SECTOR_SIZE, and use these symbolic
names throughout. Tell the blk_queue system our physical
block size, in the (unlikely) event we want to use something
other than the default.
- Delete the definition of struct rbd_info, which is never used.
- Move the definition of dev_to_rbd() down in its source file,
just above where it gets first used, and change its name to
dev_to_rbd_dev().
- Replace an open-coded operation in rbd_dev_release() to use
dev_to_rbd_dev() instead.
- Calculate the segment size for a given rbd_device just once in
rbd_init_disk().
- Use the '%zd' conversion specifier in rbd_snap_size_show(),
since the value formatted is a size_t.
- Switch to the '%llu' conversion specifier in rbd_snap_id_show().
since the value formatted is unsigned.
Signed-off-by: Alex Elder <elder@dreamhost.com>
A few blocks of code are rearranged a bit here:
- In rbd_header_from_disk():
- Don't bother computing snap_count until we're sure the
on-disk header starts with a good signature.
- Move a few independent lines of code so they are *after* a
check for a failed memory allocation.
- Get rid of unnecessary local variable "ret".
- Make a few other changes in rbd_read_header(), similar to the
above--just moving things around a bit while preserving the
functionality.
- In rbd_rq_fn(), just assign rq in the while loop's controlling
expression rather than duplicating it before and at the end of
the loop body. This allows the use of "continue" rather than
"goto next" in a number of spots.
- Rearrange the logic in snap_by_name(). End result is the same.
Signed-off-by: Alex Elder <elder@dreamhost.com>
Once rbd_bus_type is registered, it allows an "add" operation via
the /sys/bus/rbd/add bus attribute, and adding a new rbd device that
way establishes a connection between the device and rbd_root_dev.
But rbd_root_dev is not registered until after the rbd_bus_type
registration is complete. This could (in principle anyway) result
in an invalid state.
Since rbd_root_dev has no tie to rbd_bus_type we can reorder these
two initializations and never be faced with this scenario.
In addition, unregister the device in the event the bus registration
fails at module init time.
Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
The mon_addrs buffer in rbd_add is used to hold a copy of the
monitor IP addresses supplied via /sys/bus/rbd/add. That is
passed to rbd_get_client(), which never modifies it (nor do
any of the functions it gets passed to thereafter)--the mon_addr
parameter to rbd_get_client() is a pointer to constant data, so it
can't be modifed. Furthermore, rbd_get_client() has the length of
the mon_addrs buffer and that is used to ensure nothing goes beyond
its end.
Based on all this, there is no reason that a buffer needs to
be used to hold a copy of the mon_addrs provided via
/sys/bus/rbd/add. Instead, the location within that passed-in
buffer can be provided, along with the length of the "token"
therein which represents the monitor IP's.
A small change to rbd_add_parse_args() allows the address within the
buffer to be passed back, and the length is already returned. This
now means that, at least from the perspective of this interface,
there is no such thing as a list of monitor addresses that is too
long.
Signed-off-by: Alex Elder <elder@dreamhost.com>
The argument parsing routine already computes the size of the
mon_addrs buffer it extracts from the "command." Pass it to the
caller so it can use it to provide the length to rbd_get_client().
Signed-off-by: Alex Elder <elder@dreamhost.com>
This is a bit gratuitous, but there are a few things that can be
verified at build time rather than run time, so do that.
Signed-off-by: Alex Elder <elder@dreamhost.com>
Make use of a few simple helper routines to parse the arguments
rather than sscanf(). This will treat both missing and too-long
arguments as invalid input (rather than silently truncating the
input in the too-long case). In time this can also be used by
rbd_add() to use the passed-in buffer in place, rather than copying
its contents into new buffers.
It appears to me that the sscanf() previously used would not
correctly handle a supplied snapshot--the two final "%s" conversion
specifications were not separated by a space, and I'm not sure
how sscanf() handles that situation. It may not be well-defined.
So that may be a bug this change fixes (but I didn't verify that).
The sizes of the mon_addrs and options buffers are now passed to
rbd_add_parse_args(), so they can be supplied to copy_token().
Signed-off-by: Alex Elder <elder@dreamhost.com>
Move the code that parses the arguments provided to rbd_add() (which
are supplied via /sys/bus/rbd/add) into a separate function.
Also rename the "mon_dev_name" variable in rbd_add() to be
"mon_addrs". The variable represents a list of one or more
comma-separated monitor IP addresses, each with an optional port
number. I think "mon_addrs" captures that notion a little better.
Signed-off-by: Alex Elder <elder@dreamhost.com>
If a couple pointers are initialized to NULL then a single
"out_nomem" label can be used for all of the memory allocation
failure cases in rbd_add().
Also, get rid of the "irc" local variable there. There is no
real need for "rc" to be type ssize_t, and it can be used in
the spot "irc" was.
Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
The length of the string containing the monitor address
specification(s) will never exceed the length of the string passed
in to rbd_add(). The same holds true for the ceph + rbd options
string. So reduce the amount of memory allocated for these to
that length rather than the maximum (1024 bytes).
Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
Since rbd_get_client() currently returns an error code. It assigns
the rbd_client field of the rbd_device structure it is passed if
successful. Instead, have it return the created rbd_client
structure and return a pointer-coded error if there is an error.
This makes the assignment of the client pointer more obvious at the
call site.
Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
Here are a few very simple cleanups:
- Add a "RBD_" prefix to the two driver name string definitions.
- Move the definition of struct rbd_request below struct rbd_req_coll
to avoid the need for an empty declaration of the latter.
- Move and group the definitions of rbd_root_dev_release() and
rbd_root_dev, as well as rbd_bus_type and rbd_bus_attrs[],
close to the top of the file. Arrange the latter so
rbd_bus_type.bus_attrs can be initialized statically.
- Get rid of an unnecessary local variable in rbd_open().
- Rework some hokey logic in rbd_bus_add_dev(), so the value of
"ret" at the end is either 0 or -ENOENT to avoid the need for
the code duplication that was there.
- Rename a goto target in rbd_add().
Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
The spinlock used to protect rbd_client_list is named "node_lock".
Rename it to "rbd_client_list_lock" to make it more obvious what
it's for.
Signed-off-by: Alex Elder <elder@dreamhost.com>
Signed-off-by: Sage Weil <sage@newdream.net>
