The APIC LVTT register is MMIO mapped but the TSC_DEADLINE register is an
MSR. The write to the TSC_DEADLINE MSR is not serializing, so it's not
guaranteed that the write to LVTT has reached the APIC before the
TSC_DEADLINE MSR is written. In such a case the write to the MSR is
ignored and as a consequence the local timer interrupt never fires.
The SDM decribes this issue for xAPIC and x2APIC modes. The
serialization methods recommended by the SDM differ.
xAPIC:
"1. Memory-mapped write to LVT Timer Register, setting bits 18:17 to 10b.
2. WRMSR to the IA32_TSC_DEADLINE MSR a value much larger than current time-stamp counter.
3. If RDMSR of the IA32_TSC_DEADLINE MSR returns zero, go to step 2.
4. WRMSR to the IA32_TSC_DEADLINE MSR the desired deadline."
x2APIC:
"To allow for efficient access to the APIC registers in x2APIC mode,
the serializing semantics of WRMSR are relaxed when writing to the
APIC registers. Thus, system software should not use 'WRMSR to APIC
registers in x2APIC mode' as a serializing instruction. Read and write
accesses to the APIC registers will occur in program order. A WRMSR to
an APIC register may complete before all preceding stores are globally
visible; software can prevent this by inserting a serializing
instruction, an SFENCE, or an MFENCE before the WRMSR."
The xAPIC method is to just wait for the memory mapped write to hit
the LVTT by checking whether the MSR write has reached the hardware.
There is no reason why a proper MFENCE after the memory mapped write would
not do the same. Andi Kleen confirmed that MFENCE is sufficient for the
xAPIC case as well.
Issue MFENCE before writing to the TSC_DEADLINE MSR. This can be done
unconditionally as all CPUs which have TSC_DEADLINE also have MFENCE
support.
[ tglx: Massaged the changelog ]
Signed-off-by: Shaohua Li <shli@fb.com>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Cc: <Kernel-team@fb.com>
Cc: <lenb@kernel.org>
Cc: <fenghua.yu@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: stable@vger.kernel.org #v3.7+
Link: http://lkml.kernel.org/r/20150909041352.GA2059853@devbig257.prn2.facebook.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The recent ioapic cleanups changed the affinity setting in
setup_ioapic_dest() from a direct write to the hardware to the delayed
affinity setup via irq_set_affinity().
That results in a warning from chained_irq_exit():
WARNING: CPU: 0 PID: 5 at kernel/irq/migration.c:32 irq_move_masked_irq
[<ffffffff810a0a88>] irq_move_masked_irq+0xb8/0xc0
[<ffffffff8103c161>] ioapic_ack_level+0x111/0x130
[<ffffffff812bbfe8>] intel_gpio_irq_handler+0x148/0x1c0
The reason is that irq_set_affinity() does not write directly to the
hardware. It marks the affinity setting as pending and executes it
from the next interrupt. The chained handler infrastructure does not
take the irq descriptor lock for performance reasons because such a
chained interrupt is not visible to any interfaces. So the delayed
affinity setting triggers the warning in irq_move_masked_irq().
Restore the old behaviour by calling the set_affinity function of the
ioapic chip in setup_ioapic_dest(). This is safe as none of the
interrupts can be on the fly at this point.
Fixes: aa5cb97f14 'x86/irq: Remove x86_io_apic_ops.set_affinity and related interfaces'
Reported-and-tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: jarkko.nikula@linux.intel.com
When restoring the system register state for an AArch32 guest at EL2,
writes to DACR32_EL2 may not be correctly synchronised by Cortex-A57,
which can lead to the guest effectively running with junk in the DACR
and running into unexpected domain faults.
This patch works around the issue by re-ordering our restoration of the
AArch32 register aliases so that they happen before the AArch64 system
registers. Ensuring that the registers are restored in this order
guarantees that they will be correctly synchronised by the core.
Cc: <stable@vger.kernel.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- Fix timer interrupt injection after the rework
that went in during the merge window
- Reset the timer to zero on reboot
- Make sure the TCR_EL2 RES1 bits are really set to 1
- Fix a PSCI affinity bug for non-existing vcpus
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=G02h
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
KVM/ARM changes for 4.3-rc2
- Fix timer interrupt injection after the rework
that went in during the merge window
- Reset the timer to zero on reboot
- Make sure the TCR_EL2 RES1 bits are really set to 1
- Fix a PSCI affinity bug for non-existing vcpus
If there is already some polling ongoing, it's impossible to disable the
polling, since as soon as somebody sets halt_poll_ns to 0, polling will
never stop, as grow and shrink are only handled if halt_poll_ns is != 0.
This patch fix it by reset vcpu->halt_poll_ns in order to stop polling
when polling is disabled.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Depending on CONFIG_ARM64_HW_AFDBM, we use either bit 57 or 51 of the
pte to represent PTE_WRITE. Given that bit 51 is reserved prior to
ARMv8.1, we can just use that bit regardless of the config option. That
also matches what happens if a kernel configured with ARM64_HW_AFDBM=y
is run on a CPU without the DBM functionality.
Cc: Julien Grall <julien.grall@citrix.com>
Tested-by: Julien Grall <julien.grall@citrix.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The pte_modify() function with hardware AF/DBM enabled must transfer the
hardware dirty information to the software PTE_DIRTY bit. However, it
was setting this bit in newprot and the mask does not cover such bit.
This patch sets PTE_DIRTY on the original pte which will be preserved in
the returned value.
Fixes: 2f4b829c62 ("arm64: Add support for hardware updates of the access and dirty pte bits")
Cc: Julien Grall <julien.grall@citrix.com>
Tested-by: Julien Grall <julien.grall@citrix.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 2f4b829c62 ("arm64: Add support for hardware updates of the
access and dirty pte bits") introduced support for handling hardware
updates of the access flag and dirty status. The PTE is automatically
dirtied in hardware (if supported) by clearing the PTE_RDONLY bit when
the PTE_DBM/PTE_WRITE bit is set. The pte_hw_dirty() macro was added to
detect a hardware dirtied pte. The pte_dirty() macro checks for both
software PTE_DIRTY and pte_hw_dirty().
Functions like pte_modify() clear the PTE_RDONLY bit since it is meant
to be set in set_pte_at() when written to memory. In such cases,
pte_hw_dirty() would return true even though such pte is clean. This
patch changes pte_hw_dirty() to test the PTE_DBM/PTE_WRITE bit together
with PTE_RDONLY.
Fixes: 2f4b829c62 ("arm64: Add support for hardware updates of the access and dirty pte bits")
Reported-by: Julien Grall <julien.grall@citrix.com>
Tested-by: Julien Grall <julien.grall@citrix.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If CMA is turned on and CMA size is set to zero, kernel should
behave as if CMA was not enabled at compile time.
Every dma allocation should check existence of cma area
before requesting memory.
Arm has done this by commit e464ef16c4 ("arm: dma-mapping: add
checking cma area initialized"), also do this for arm64.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
While the following commit:
37868fe113 ("x86/ldt: Make modify_ldt synchronous")
added a nice comment explaining that Xen needs page-aligned
whole page chunks for guest descriptor tables, it then
nevertheless used kzalloc() on the small size path.
As I'm unaware of guarantees for kmalloc(PAGE_SIZE, ) to return
page-aligned memory blocks, I believe this needs to be switched
back to __get_free_page() (or better get_zeroed_page()).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/55E735D6020000780009F1E6@prv-mh.provo.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The CONFIG_VM86 Kconfig help text is actively misleading, so fix it:
- Don't mark it 'obsolete' in the text as we'll support the ABI as long as CPUs
support it.
- Qualify the part about software emulation and mention that for some apps you
want a real vm86 mode.
- Don't scare users away from the option, instead explain what it does.
Reported-by: Stas Sergeev <stsp@list.ru>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Austin S Hemmelgarn <ahferroin7@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Search and replace done with coccinelle
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linuxppc-dev@lists.ozlabs.org
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: linuxppc-dev@lists.ozlabs.org
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: linuxppc-dev@lists.ozlabs.org
User visible:
- The values of _SC_NPROCESSORS_CONF and _SC_NPROCESSORS_ONLN (sysconf(3)) were
being read from perf.data files in the inverse order they are written, fix it.
(Arnaldo Carvalho de Melo)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8u6b
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fix from Arnaldo Carvalho de Melo:
- The values of _SC_NPROCESSORS_CONF and _SC_NPROCESSORS_ONLN (sysconf(3)) were
being read from perf.data files in the inverse order they are written, fix it.
(Arnaldo Carvalho de Melo)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
?SYNTAX ERROR
irq_desc_get_irq_chip() does not exist. It should
be irq_desc_get_chip(). Tested by compiling
s3c2410_defconfig.
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the gpio driver is confused about the numbers for gpio-ranges,
pinctrl_ready_for_gpio_range() may get called with invalid GPIO
causing a NULL pointer exception. Let's instead provide a warning
that allows fixing the problem and return with error.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no reason to break a line shorter than 80 columns.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 323de9efdf ("pinctrl: make pinctrl_register() return proper
error code"), pinctrl_register returns an error code rather than NULL on
failure. Update a driver that was introduced more recently.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1,e2;
@@
e = pinctrl_register(...)
... when != e = e1
if (
- e == NULL
+ IS_ERR(e)
) {
...
return
- e2
+ PTR_ERR(e)
;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 323de9efdf ("pinctrl: make pinctrl_register() return proper
error code"), pinctrl_register returns an error code rather than NULL on
failure. Update some drivers that were introduced more recently.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1,e2;
@@
e = pinctrl_register(...)
... when != e = e1
if (
- e == NULL
+ IS_ERR(e)
) {
...
return
- e2
+ PTR_ERR(e)
;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If gpio-omap probe fails with -EPROBE_DEFER, the GPIO numbering
keeps increasing. Only increase the gpio count if gpiochip_add()
was successful as otherwise the numbers will increase for each
probe attempt.
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO documentation mentions that GPIOs are mapped by defining a
<function>-gpios property in the consumer device's node but a -gpio
sufix is also supported after commit:
dd34c37aa3 ("gpio: of: Allow -gpio suffix for property names")
Update the documentation to match the implementation.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver has a I2C device id table that is used to create the module
aliases and also "sx150x" isn't a supported I2C id, so it's never used.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The con_id parameter has to match the GPIO description and is automatically
extended by the GPIO suffix if not NULL. I had to look into the code to
understand this and properly find the GPIO I've been looking for, so document
this.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With commit 39b2bbe3d7 ("gpio: add flags argument to gpiod_get*()
functions") the gpiod_get*() functions got a 'flags' parameter. Reflect
this in the documentation, too.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's possible to have gpio chips hanging off unreliable remote buses
where the get() operation will fail to acquire a readout of the current
gpio state. Propagate these errors to the consumer so that they can
act on, retry or ignore these failing reads, instead of treating them as
the line being held high.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
8cd1470("gpio: rcar: Add r8a7795 (R-Car H3) support") added
GPIO support for r8a7795. r8a7795 based on CONFIG_ARM64.
OTOH, GPIO_RCAR driver can be compiled fine on non-ARM.
This patch removed ARM dependency for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Need to check return value of irq_alloc_generic_chip, because
it may return NULL.
1. Change mxs_gpio_init_gc return type from void to int.
2. Add a new lable out_irqdomain_remove to remove the irq domain
when mxc_gpio_init_gc fail.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Need to check return value of irq_alloc_generic_chip, because
it may return NULL.
1. Change mxc_gpio_init_gc return type from void to int.
2. Add a new lable out_irqdomain_remove to remove the irq domain
when mxc_gpio_init_gc fail.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
[Manually rebased]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The internal clocksteering done for fine-grained error
correction uses a logarithmic approximation, so any time
adjtimex() adjusts the clock steering, timekeeping_freqadjust()
quickly approximates the correct clock frequency over a series
of ticks.
Unfortunately, the logic in timekeeping_freqadjust(), introduced
in commit:
dc491596f6 ("timekeeping: Rework frequency adjustments to work better w/ nohz")
used the abs() function with a s64 error value to calculate the
size of the approximated adjustment to be made.
Per include/linux/kernel.h:
"abs() should not be used for 64-bit types (s64, u64, long long) - use abs64()".
Thus on 32-bit platforms, this resulted in the clocksteering to
take a quite dampended random walk trying to converge on the
proper frequency, which caused the adjustments to be made much
slower then intended (most easily observed when large
adjustments are made).
This patch fixes the issue by using abs64() instead.
Reported-by: Nuno Gonçalves <nunojpg@gmail.com>
Tested-by: Nuno Goncalves <nunojpg@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: <stable@vger.kernel.org> # v3.17+
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Miroslav Lichvar <mlichvar@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1441840051-20244-1-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Sasha reported that we can get here with .idx==-1, and
cpuc->event_constraints unallocated.
Suggested-by: Stephane Eranian <eranian@google.com>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Fixes: b371b59431 ("perf/x86: Fix event/group validation")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
924e101a7a ("x86/debug: Dump family, model, stepping of the
boot CPU") had its good intentions to dump the exact F/M/S as an
aid during debugging sessions but its output can be ambiguous.
Fix that:
-smpboot: CPU0: Intel Core Processor (Broadwell) (fam: 06, model: 47, stepping: 02)
+smpboot: CPU0: Intel Core Processor (Broadwell) (family: 0x6, model: 0x47, stepping: 0x2)
Also, spell out "family".
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1441914927-32037-1-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
NCT6793D is register compatible with NCT6792D.
Also move nct6775_sio_names[] closer to enum kinds to simplify
adding new chips.
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The STEP_UP_TIME and STEP_DOWN_TIME registers are swapped for all chips but
NCT6775.
Reported-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlXqI2YACgkQ31LbvUHyf1eV9QCdH1QQrv3ze1j+5ut3hVGQFC7F
s0oAnRWfi65O5J6Ns4gEGfbjSXvF2aNf
=5RcU
-----END PGP SIGNATURE-----
Merge tag 'cris-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull CRIS updates from Jesper Nilsson:
"Mostly removal of old cruft of which we can use a generic version, or
fixes for code not commonly run in the cris port, but also additions
to enable some good debug"
* tag 'cris-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris: (25 commits)
CRISv10: delete unused lib/dmacopy.c
CRISv10: delete unused lib/old_checksum.c
CRIS: fix switch_mm() lockdep splat
CRISv32: enable LOCKDEP_SUPPORT
CRIS: add STACKTRACE_SUPPORT
CRISv32: annotate irq enable in idle loop
CRISv32: add support for irqflags tracing
CRIS: UAPI: use generic types.h
CRIS: UAPI: use generic shmbuf.h
CRIS: UAPI: use generic msgbuf.h
CRIS: UAPI: use generic socket.h
CRIS: UAPI: use generic sembuf.h
CRIS: UAPI: use generic sockios.h
CRIS: UAPI: use generic auxvec.h
CRIS: UAPI: use generic headers via Kbuild
CRIS: UAPI: fix elf.h export
CRIS: don't make asm/elf.h depend on asm/user.h
CRIS: UAPI: fix ptrace.h
CRISv32: Squash compile warnings for axisflashmap
CRISv32: Add GPIO driver to the default configs
...
rq_data_dir() returns either READ or WRITE (0 == READ, 1 == WRITE), not
a boolean value.
Now, admittedly the "!= 0" doesn't really change the value (0 stays as
zero, 1 stays as one), but it's not only redundant, it confuses gcc, and
causes gcc to warn about the construct
switch (rq_data_dir(req)) {
case READ:
...
case WRITE:
...
that we have in a few drivers.
Now, the gcc warning is silly and stupid (it seems to warn not about the
switch value having a different type from the case statements, but about
_any_ boolean switch value), but in this case the code itself is silly
and stupid too, so let's just change it, and get rid of warnings like
this:
drivers/block/hd.c: In function ‘hd_request’:
drivers/block/hd.c:630:11: warning: switch condition has boolean value [-Wswitch-bool]
switch (rq_data_dir(req)) {
The odd '!= 0' came in when "cmd_flags" got turned into a "u64" in
commit 5953316dbf ("block: make rq->cmd_flags be 64-bit") and is
presumably because the old code (that just did a logical 'and' with 1)
would then end up making the type of rq_data_dir() be u64 too.
But if we want to retain the old regular integer type, let's just cast
the result to 'int' rather than use that rather odd '!= 0'.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the writeback plugging introduced in commit d353d7587d
("writeback: plug writeback at a high level") that then caused problems
due to the unplug happening with a spinlock held.
* writeback-plugging:
writeback: plug writeback in wb_writeback() and writeback_inodes_wb()
Revert "writeback: plug writeback at a high level"
We had to revert the pluggin in writeback_sb_inodes() because the
wb->list_lock is held, but we could easily plug at a higher level before
taking that lock, and unplug after releasing it. This does that.
Chris will run performance numbers, just to verify that this approach is
comparable to the alternative (we could just drop and re-take the lock
around the blk_finish_plug() rather than these two commits.
I'd have preferred waiting for actual performance numbers before picking
one approach over the other, but I don't want to release rc1 with the
known "sleeping function called from invalid context" issue, so I'll
pick this cleanup version for now. But if the numbers show that we
really want to plug just at the writeback_sb_inodes() level, and we
should just play ugly games with the spinlock, we'll switch to that.
Cc: Chris Mason <clm@fb.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Jan Kara <jack@suse.cz>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I didn't notice this when merging the thermal code from Zhang, but his
merge (commit 5a924a07f882: "Merge branches 'thermal-core' and
'thermal-intel' of .git into next") of the thermal-core and
thermal-intel branches was wrong.
In thermal-core, commit 17e8351a77 ("thermal: consistently use int for
temperatures") converted the thermal layer to use "int" for
temperatures.
But in parallel, in the thermal-intel branch commit d0a12625d2
("thermal: Add Intel PCH thermal driver") added support for the intel
PCH thermal sensor using the old interfaces that used "unsigned long"
pointers.
This resulted in warnings like this:
drivers/thermal/intel_pch_thermal.c:184:14: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.get_temp = pch_thermal_get_temp,
^
drivers/thermal/intel_pch_thermal.c:184:14: note: (near initialization for ‘tzd_ops.get_temp’)
drivers/thermal/intel_pch_thermal.c:186:19: warning: initialization from incompatible pointer type [-Wincompatible-pointer-types]
.get_trip_temp = pch_get_trip_temp,
^
drivers/thermal/intel_pch_thermal.c:186:19: note: (near initialization for ‘tzd_ops.get_trip_temp’)
This fixes it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge fourth patch-bomb from Andrew Morton:
- sys_membarier syscall
- seq_file interface changes
- a few misc fixups
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
revert "ocfs2/dlm: use list_for_each_entry instead of list_for_each"
mm/early_ioremap: add explicit #include of asm/early_ioremap.h
fs/seq_file: convert int seq_vprint/seq_printf/etc... returns to void
selftests: enhance membarrier syscall test
selftests: add membarrier syscall test
sys_membarrier(): system-wide memory barrier (generic, x86)
MODSIGN: fix a compilation warning in extract-cert
improvements, and adding a mailing list to MAINTAINERS for NTB.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=CASz
-----END PGP SIGNATURE-----
Merge tag 'ntb-4.3' of git://github.com/jonmason/ntb
Pull NTB fixes from Jon Mason:
"NTB bug and documentation fixes, new device IDs, performance
improvements, and adding a mailing list to MAINTAINERS for NTB"
* tag 'ntb-4.3' of git://github.com/jonmason/ntb:
NTB: Fix range check on memory window index
NTB: Improve index handling in B2B MW workaround
NTB: Fix documentation for ntb_peer_db_clear.
NTB: Fix documentation for ntb_link_is_up
NTB: Use unique DMA channels for TX and RX
NTB: Remove dma_sync_wait from ntb_async_rx
NTB: Clean up QP stats info
NTB: Make the transport list in order of discovery
NTB: Add PCI Device IDs for Broadwell Xeon
NTB: Add flow control to the ntb_netdev
NTB: Add list to MAINTAINERS