This improves bitops usages in several points:
- Convert u64 to a proper bitmap declaration. This enables to remove
superfluous typecasting from 'u64' to 'unsigned long *'.
- Convert superfluous atomic bitops to non atomic bitops. The bitmap
is allocated on the stack and it is not accessed by any other threads,
so using atomic bitops is not necessary.
- Use find_next_zero_bit and find_next_zero_bit instead of calling
test_bit() for each bit.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Bonding in balance-alb mode records information from ARP packets
passing through the bond in a hash table (rx_hashtbl).
At certain situations (e.g. link change of a slave),
rlb_update_rx_clients() will send out ARP packets to update ARP
caches of other hosts on the network to achieve RX load
balancing.
The problem is that once an IP address is recorded in the hash
table, it stays there indefinitely. If this IP address is
migrated to a different host in the network, bonding still sends
out ARP packets that poison other systems' ARP caches with
invalid information.
This patch solves this by looking at all incoming ARP packets,
and checking if the source IP address is one of the source
addresses stored in the rx_hashtbl. If it is, but the MAC
addresses differ, the corresponding hash table entries are
removed. Thus, when an IP address is migrated, the first ARP
broadcast by its new owner will purge the offending entries of
rx_hashtbl.
The hash table is hashed by ip_dst. To be able to do the above
check efficiently (not walking the whole hash table), we need a
reverse mapping (by ip_src).
I added three new members in struct rlb_client_info:
rx_hashtbl[x].src_first will point to the start of a list of
entries for which hash(ip_src) == x.
The list is linked with src_next and src_prev.
When an incoming ARP packet arrives at rlb_arp_recv()
rlb_purge_src_ip() can quickly walk only the entries on the
corresponding lists, i.e. the entries that are likely to contain
the offending IP address.
To avoid confusion, I renamed these existing fields of struct
rlb_client_info:
next -> used_next
prev -> used_prev
rx_hashtbl_head -> rx_hashtbl_used_head
(The current linked list is _not_ a list of hash table
entries with colliding ip_dst. It's a list of entries that are
being used; its purpose is to avoid walking the whole hash table
when looking for used entries.)
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not modify or load balance ARP packets passing through balance-alb
mode (wherein the ARP did not originate locally, and arrived via a bridge).
Modifying pass-through ARP replies causes an incorrect MAC address
to be placed into the ARP packet, rendering peers unable to communicate
with the actual destination from which the ARP reply originated.
Load balancing pass-through ARP requests causes an entry to be
created for the peer in the rlb table, and bond_alb_monitor will
occasionally issue ARP updates to all peers in the table instrucing them
as to which MAC address they should communicate with; this occurs when
some event sets rx_ntt. In the bridged case, however, the MAC address
used for the update would be the MAC of the slave, not the actual source
MAC of the originating destination. This would render peers unable to
communicate with the destinations beyond the bridge.
Signed-off-by: Zheng Li <zheng.x.li@oracle.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable open_time in the struct peak_usb_device was used to protect
peak_usb_set_mode() only to be called, if the interface is up. Now the CAN
device infrastructure takes care of this.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The variable open_time in the struct esd_usb2_net_priv was used to protect
esd_usb2_set_mode() only to be called, if the interface is up. Now the CAN
device infrastructure takes care of this.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The variable open_time in the struct ems_usb was used to protect
ems_usb_set_mode() only to be called, if the interface is up. Now the CAN
device infrastructure takes care of this.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The variable open_time in the struct sja1000_priv was used to protect
sja1000_set_mode() only to be called, if the interface is up. Now the CAN
device infrastructure takes care of this.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The variable open_time in the struct mscan_priv was used to protect
mscan_do_set_mode() only to be called, if the interface is up. Now the CAN
device infrastructure takes care of this.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the restart timer is running due to BUS-OFF and the device is
disconnected an dev_put will decrease the usage counter to -1 thus
blocking the interface removal, resulting in the following dmesg
lines repeating every 10s:
can: notifier: receive list not found for dev can0
can: notifier: receive list not found for dev can0
can: notifier: receive list not found for dev can0
unregister_netdevice: waiting for can0 to become free. Usage count = -1
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pull networking fixes from David Miller:
"Some more fixes trickled in over the past few days:
1) PIM device names can overflow the IFNAMSIZ buffer unless we
properly limit the allowed indexes, fix from Eric Dumazet.
2) Under heavy load we can OOPS in icmp reply processing due to an
unchecked inet_putpeer() call. Fix from Neal Cardwell.
3) SCTP round trip calculations need to use 64-bit math to avoid
overflows, fix from Schoch Christian.
4) Fix a memory leak and an error return flub in SCTP and IRDA
triggerable by userspace. Fix from Tommi Rantala and found by the
syscall fuzzer (trinity).
5) MLX4 driver gives bogus size to memcpy() call, fix from Amir
Vadai.
6) Fix length calculation in VHOST descriptor translation, from
Michael S Tsirkin.
7) Ambassador ATM driver loops forever while loading firmware, fix
from Dan Carpenter.
8) Over MTU packets in openvswitch warn about wrong device, fix from
Jesse Gross.
9) Netfilter IPSET's netlink code can overrun a string buffer because
it's not properly limited to IFNAMSIZ. Fix from Florian Westphal.
10) PCAN USB driver sets wrong timestamp in SKB, from Oliver Hartkopp.
11) Make sure the RX ifindex always has a valid value in the CAN BCM
driver, even if we haven't received a frame yet. Fix also from
Oliver Hartkopp."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
team: fix hw_features setup
atm: forever loop loading ambassador firmware
vhost: fix length for cross region descriptor
irda: irttp: fix memory leak in irttp_open_tsap() error path
net: qmi_wwan: add Huawei E173
net/mlx4_en: Can set maxrate only for TC0
sctp: Error in calculation of RTTvar
sctp: fix -ENOMEM result with invalid user space pointer in sendto() syscall
sctp: fix memory leak in sctp_datamsg_from_user() when copy from user space fails
net: ipmr: limit MRT_TABLE identifiers
ipv4: avoid passing NULL to inet_putpeer() in icmpv4_xrlim_allow()
can: bcm: initialize ifindex for timeouts without previous frame reception
can: peak_usb: fix hwtstamp assignment
netfilter: ipset: fix netiface set name overflow
openvswitch: Store flow key len if ARP opcode is not request or reply.
openvswitch: Print device when warning about over MTU packets.
CC drivers/net/ethernet/ti/cpsw.o
drivers/net/ethernet/ti/cpsw.c: In function 'cpsw_ndo_ioctl':
drivers/net/ethernet/ti/cpsw.c:881:20: warning: unused variable 'priv'
The build warning is generated when CPTS is not selected in Kernel Build.
Fixing by passing the net_device pointer to cpts IOCTL instead of passing priv
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This pull request is intended for the 3.8 stream. It is a bit large
-- I guess Thanksgiving got me off track! At least the code got to
spend some time in linux-next... :-)
This includes the usual batch of pulls for Bluetooth, NFC, and mac80211
as well as iwlwifi. Also here is an ath6kl pull, and a new driver
in the rtlwifi family. The brcmfmac, brcmsmac, ath9k, and mwl8k get
their usual levels of attention, and a handful of other updates tag
along as well.
For more detail on the pulls, please see below...
On Bluetooth, Gustavo says:
"Another set of patches for integration in wireless-next. There are two big set
of changes in it: Andrei Emeltchenko and Mat Martineau added more patches
towards a full Bluetooth High Speed support and Johan Hedberg improve the
single mode support for Bluetooth dongles. Apart from that we have small fixes
and improvements."
...and:
"A few patches to 3.8. The majority of the work here is from Andrei on the High
Speed support. Other than that Johan added support for setting LE advertising
data. The rest are fixes and clean ups and small improvements like support for
a new broadcom hardware."
On mac80211, Johannes says:
"This is for mac80211, for -next (3.8). Plenty of changes, as you can see
below. Some fixes for previous changes like the export.h include, the
beacon listener fix from Ben Greear, etc. Overall, no exciting new
features, though hwsim does gain channel context support for people to
try it out and look at."
...and...:
"This one contains the mac80211-next material. Apart from a few small new
features and cleanups I have two fixes for the channel context code. The
RX_END timestamp support will probably be reworked again as Simon Barber
noted the calculations weren't really valid, but the discussions there
are still going on and it's better than what we had before."
...and:
"Please pull (see below) to get the following changes:
* a fix & a debug aid in IBSS from Antonio,
* mesh cleanups from Marco,
* a few bugfixes for some of my previous patches from Arend and myself,
* and the big initial VHT support patchset"
And on iwlwifi, Johannes says:
"In addition to the previous four patches that I'm not resending,
we have a number of cleanups, message reduction, firmware error
handling improvements (yes yes... we need to fix them instead)
and various other small things all over."
...and:
"In his quest to try to understand the current iwlwifi problems (like
stuck queues etc.) Emmanuel has first cleaned up the PCIe code, I'm
including his changes in this pull request. Other than that I only have
a small cleanup from Sachin Kamat to remove a duplicate include and a
bugfix to turn off MFP if software crypto is enabled, but this isn't
really interesting as MFP isn't supported right now anyway."
On NFC, Samuel says:
"With this one we have:
- A few HCI improvements in preparation for an upcoming HCI chipset support.
- A pn544 code cleanup after the old driver was removed.
- An LLCP improvement for notifying user space when one peer stops ACKing I
frames."
On ath6kl, Kalle says:
"Major changes this time are firmware recover support to gracefully
handle if firmware crashes, support for changing regulatory domain and
support for new ar6004 hardware revision 1.4. Otherwise there are just
smaller fixes or cleanups from different people."
Thats about it... :-) Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ff33c0e188 ('net: Remove bogus
dependencies on INET') wrongly removed this dependency. cxgb3 uses
the arp_send() function defined in net/ipv4/arp.c.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do this in the same way bonding does. This fixed setup resolves performance
issues when using some cards with certain offloading.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a forever loop introduced here when we converted this to
request_firmware() back in 2008.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
On BE2 chip, an interrupt may be raised even when EQ is in un-armed state.
As a result be_intx()::events_get() and be_poll:events_get() can race and
notify an EQ wrongly.
Fix this by counting events only in be_poll(). Commit 0b545a629 fixes
the same issue in the MSI-x path.
But, on Lancer, INTx can be de-asserted only by notifying num evts. This
is not an issue as the above BE2 behavior doesn't exist/has never been
seen on Lancer.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove an outdated comment, that should have been removed in the
patch named "MODULE_PARM conversions" from early 2005.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building ewrk3.o triggers this GCC warning:
drivers/net/ethernet/dec/ewrk3.c: In function '__check_irq':
drivers/net/ethernet/dec/ewrk3.c:1915:1: warning: return from incompatible pointer type [enabled by default]
This can be trivially fixed by changing the 'irq' parameter from int to
byte (which is an alias for unsigned char for module parameters).
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
this is pull request is for net-next. Contains a patch by Andreas
Larsson, which enables the sja1000 of driver to work under sparc.
AnilKumar Ch contributed a patch to improve the c_can support under
omap, Olivier Sobrie's patch brings support for the CAN/USB dongles
from Kvaser. In a bunch of patches by me missing MODULE_ALIAS and/or
MODULE_DEVICE_TABLE entries were added to the CAN drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If all slaves of a balance-rr bond with ARP monitor are enslaved
with down link state, bond keeps down state even after slaves
go up.
This is caused by bond_enslave() setting curr_active_slave to
first slave not taking into account its link state. As
bond_loadbalance_arp_mon() uses curr_active_slave to identify
whether slave's down->up transition should update bond's link
state, bond stays down even if slaves are up (until first slave
goes from up to down at least once).
Before commit f31c7937 "bonding: start slaves with link down for
ARP monitor", this was masked by slaves always starting in UP
state with ARP monitor (and MII monitor not relying on
curr_active_slave being NULL if there is no slave up).
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a single descriptor crosses a region, the
second chunk length should be decremented
by size translated so far, instead it includes
the full descriptor length.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Huawei E173 is a QMI/wwan device which normally appear
as 12d1:1436 in Linux. The descriptors displayed in that
mode will be picked up by cdc_ether. But the modem has
another mode with a different device ID and a slightly
different set of descriptors. This is the mode used by
Windows like this:
3Modem: USB\VID_12D1&PID_140C&MI_00\6&3A1D2012&0&0000
Networkcard: USB\VID_12D1&PID_140C&MI_01\6&3A1D2012&0&0001
Appli.Inter: USB\VID_12D1&PID_140C&MI_02\6&3A1D2012&0&0002
PC UI Inter: USB\VID_12D1&PID_140C&MI_03\6&3A1D2012&0&0003
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Bjorn Mork, the generic "usb" driver sets this
for us so no need to directly set it in this driver.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Cc: Bjorn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for USB dynamic autosuspend to the
smsc75xx driver. This saves virtually no power in the USB
device but enables power savings in upstream hosts and
the host CPU.
Note currently Linux doesn't automatically enable this
functionality by default for devices so to test this:
echo auto > /sys/bus/usb/devices/2-1.2/power/control
where 2-1.2 is the USB bus address of the LAN7500.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures that if we fail to suspend the LAN7500 device
we call usbnet_resume before returning failure, instead of
leaving the usbnet driver in an unusable state.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables LAN7500 family devices to wake from suspend
on either link up or link down events.
It also adds _nopm versions of mdio access functions, so we can
safely call them from suspend and resume functions
Updated patch to add newlines to printk messages
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits out the logic for entering suspend modes
to separate functions, to reduce the complexity of the
smsc75xx_suspend function.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a missing check and error message if smsc75xx_reset
fails.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coding style violations in qlcnic_minidump.c
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical refactoring of 82xx adapter register dump utility.
Move register dump routines to new file qlcnic_minidump.c
Existing register dump routines has coding style issues, the code
is moved to the new file without fixing the style issues.
There is a seperate patch to fix the style issues in qlcnic_minidump.c
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coding style issues in qlcnic_sysfs.c file
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical refactoring of 82xx adapter sysfs routines.
Move sysfs routines to new file qlcnic_sysfs.c
Existing sysfs routines has coding style issues, this code is
moved to the new file without fixing the style issues.
There is a seperate patch to fix the style issues in qlcnic_sysfs.c
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical refactoring of 82xx adapter data path routines.
Move data path code to new file qlcnic_io.c
Existing data path code has coding stye issues, the code is
moved to the new file without fixing the style issues.
There is a seperate patch to fix the style issues in qlcnic_io.c
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to igb, igbvf and ixgbe.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not a real problem, since the EEE is supported for devices where the
actual_phy_selection is zero, such that the req_duplex of params will match
the one of the phy struct.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The string was split to several lines since it reached over 180 chars, which
seems too much.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes some cosmetic changes to the code:
1. Code alignment.
2. Merge read-modify-write into a single function (read_or_write /
read_and_write).
3. Merge several write registers into a for-loop write using a static array.
4. Remove empty lines.
5. Fix comments.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taking PHY lock is not required on some older designs, but we are removing this
complication and always taking it since it is always required on newer designs
and does not worth the code complication on the older boards.
Taking PHY lock was initially required only on specific boards which had their
MDC/MDIO bus crossed, but since this lock is now always required, for example,
when NCSI is present, the PHY lock will always be taken.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the 10G-baseT PHY - BCM84834, which is the quad-port version of
the dual-port BCM84833.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per measurements, the SFP+ suffered from small current leakage in two cases:
- When no module was plugged and TX laser was disabled. The fix was to enable
it, and when module is plugged in, check if it needs to be disabled.
- When over-current event occurs due to invalid SFP+ module, the HW basically
shuts down the current for this module, but the SW needs to complete this
by issuing a power down via a GPIO.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When drivers works on top of an old bootcode, it is theoretically subjected to
MDC/MDIO failures since the MDIO clock is set in the beginning of each sequence,
rather than per CL45 command. On rare cases an old bootcodes may change that in
the middle, so to address that, the MDIO clock is set for each CL45 access.
In addition, setting the MDIO clock is now done per EMAC base, and
not per port number, since a specific port can potentially use both EMACs for
different PHY accesses.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case Link Flap Avoidance feature is supported by the MCP, bnx2x will enable
it, and will pass the appropriate parameter when load request is sent to
the MCP.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the version string to better reflect the driver functionality with
that of the out of tree driver. Also since we no longer need the MAJ,
MIN, BUILD defines remove them to clean up the code.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The internal bridge mode setting needs to be sticky so that it can be
configured correctly after a device reset. This change is required now
that the driver supports setting the bridge mode to VEB or VEPA.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The XOFF received statistic registers are per priority based and not per
traffic class. The ixgbe driver was incorrectly considering them to be for
each traffic class; and then disabling the "Tx hang" check for the queues
that belonged to the particular traffic class that had received PFC frames.
The above logic worked fine in scenario where the user priority and traffic
class number matched e.g. priority 0 is mapped to traffic class 0 and so on.
But, when multiple user priorities are mapped to a single traffic class or
when user priorities and traffic class numbers do not line up; the ixgbe
driver may disable the "Tx hang" check for queues belonging to a traffic
class that did not receive PFC frames and keep the "Tx hang" check enabled
for the queues that did receive the PFC frames.
This patch corrects the above in the code by considering the statistics
on a per priority basis; then getting the traffic class the user priority
belongs to and disabling the "Tx hang" check for queues that belong
to that traffic class.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we are doing a page based receive there is no point in setting a maximum
packet length on the x540 RXDCTL register. As such we can drop the code from
the driver entirely.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For some devices, the result of the flow control high watermark gets
truncated when programming it into the registers because of the mask used.
Switch the mask to 32-bit to prevent this from happening.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update version number.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On i350 VF devices, VLAN tags will be byte-swapped in the receive
descriptor only when received packets are looped back from other
VFs. Check for this condition and swab the tag if needed.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull media fixes from Mauro Carvalho Chehab:
"For some media fixes:
- dvb_usb_v2: some fixes at the core
- Some fixes on some embedded drivers: soc_camera, adv7604, omap3isp,
exynos/s5p
- Several Exynos4/5 camera fixes
- a fix at stv0900 driver
- a few USB ID additions to detect more variants of rtl28xxu-based
sticks"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (25 commits)
[media] rtl28xxu: 0ccd:00d7 TerraTec Cinergy T Stick+
[media] rtl28xxu: 1d19:1102 Dexatek DK mini DVB-T Dongle
[media] mt9v022: fix the V4L2_CID_EXPOSURE control
[media] mx2_camera: fix missing unlock on error in mx2_start_streaming()
[media] media: omap1_camera: fix const cropping related warnings
[media] media: mx1_camera: use the default .set_crop() implementation
[media] media: mx2_camera: fix const cropping related warnings
[media] media: mx3_camera: fix const cropping related warnings
[media] media: pxa_camera: fix const cropping related warnings
[media] media: sh_mobile_ceu_camera: fix const cropping related warnings
[media] media: sh_vou: fix const cropping related warnings
[media] adv7604: restart STDI once if format is not found
[media] adv7604: use presets where possible
[media] adv7604: Replace prim_mode by mode
[media] adv7604: cleanup references
[media] dvb_usb_v2: switch interruptible mutex to normal
[media] dvb_usb_v2: fix pid_filter callback error logging
[media] exynos-gsc: change driver compatible string
[media] omap3isp: Fix warning caused by bad subdev events operations prototypes
[media] omap3isp: video: Fix warning caused by bad vidioc_s_crop prototype
...
This patch adds a MODULE_DEVICE_TABLE for the of bindings, so that the module
can be loaded automatically by udev.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a MODULE_DEVICE_TABLE for the of and platform bindings, so that
the module can be loaded automatically by udev.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a MODULE_DEVICE_TABLE for the platform bindings, so that the
module can be loaded automatically by udev.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a MODULE_DEVICE_TABLE for the of and platform bindings, so that
the module can be loaded automatically by udev.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a MODULE_ALIAS for the platform bindings and a
MODULE_DEVICE_TABLE for of bindings, so that the module can be loaded
automatically by udev.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a MODULE_ALIAS for the platform bindings, so that the module
can be loaded automatically by udev.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a MODULE_ALIAS for the platform bindings, so that
the module can be loaded automatically udev.
Tested-by: Jan Lübbe <jlu@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a MODULE_ALIAS for the platform bindings, so that the module
can be loaded automatically by udev.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This driver provides support for several Kvaser CAN/USB devices.
Such kind of devices supports up to three CAN network interfaces.
It has been tested with a Kvaser USB Leaf Light (one network interface)
connected to a pch_can interface.
The firmware version of the Kvaser device was 2.5.205.
List of Kvaser devices supported by the driver:
- Kvaser Leaf Light
- Kvaser Leaf Professional HS
- Kvaser Leaf SemiPro HS
- Kvaser Leaf Professional LS
- Kvaser Leaf Professional SWC
- Kvaser Leaf Professional LIN
- Kvaser Leaf SemiPro LS
- Kvaser Leaf SemiPro SWC
- Kvaser Memorator II HS/HS
- Kvaser USBcan Professional HS/HS
- Kvaser Leaf Light GI
- Kvaser Leaf Professional HS (OBD-II connector)
- Kvaser Memorator Professional HS/LS
- Kvaser Leaf Light "China"
- Kvaser BlackBird SemiPro
- Kvaser USBcan R
Signed-off-by: Daniel Berglund <db@kvaser.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add D_CAN raminit support to C_CAN driver to enable D_CAN RAM,
which holds all the message objects during transmission or
receiving of data. This initialization/de-initialization should
be done in synchronous with D_CAN clock.
In case of AM335X-EVM (current user of D_CAN driver) message RAM is
controlled through control module register for both instances. So
control module register details is required to initialization or
de-initialization of message RAM according to instance number.
Control module memory resource is obtained from D_CAN dt node and
instance number obtained from device tree aliases node.
This patch was tested on AM335x-EVM along with pinctrl data addition
patch, d_can dt aliases addition and control module data addition.
pinctrl data addition is not added to am335x-evm.dts (only supports
CPLD profile#0) because d_can1 is supported under CPLD profile#1.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
[mkl: fix instance for non DT in probe, cleaned up raminit]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Merge misc fixes from Andrew Morton:
"8 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (8 patches)
futex: avoid wake_futex() for a PI futex_q
watchdog: using u64 in get_sample_period()
writeback: put unused inodes to LRU after writeback completion
mm: vmscan: check for fatal signals iff the process was throttled
Revert "mm: remove __GFP_NO_KSWAPD"
proc: check vma->vm_file before dereferencing
UAPI: strip the _UAPI prefix from header guards during header installation
include/linux/bug.h: fix sparse warning related to BUILD_BUG_ON_INVALID
Here is a single fix for a reported regression in 3.7-rc5 for the tty
layer. This fix has been in the linux-next tree and solves the reported
problem.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlCz9SgACgkQMUfUDdst+ylwJACgrm6WSMdZy+Dcg+4lY+zLftUq
UhQAn1Y00nwte19cNvJLqWYgJlqkcUBw
=NAlw
-----END PGP SIGNATURE-----
Merge tag 'tty-3.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY fix from Greg Kroah-Hartman:
"Here is a single fix for a reported regression in 3.7-rc5 for the tty
layer. This fix has been in the linux-next tree and solves the
reported problem.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty vt: Fix a regression in command line edition
We have:
- A twl fix preventing a buffer overflow.
- A wm5102 register patch fix.
- A wm5110 error misreport fix.
- Arizona fixes: Use the right array size when adding subdevices, correctly
report underclocked events, synchronize register cache after reset.
- A twl4030 fix for preventing the system to hang from an interrupt flood.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=tHAv
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD fixes from Samuel Ortiz:
- A twl fix preventing a buffer overflow.
- A wm5102 register patch fix.
- A wm5110 error misreport fix.
- Arizona fixes: Use the right array size when adding subdevices,
correctly report underclocked events, synchronize register cache
after reset.
- A twl4030 fix for preventing the system to hang from an interrupt
flood.
* tag 'mfd-for-linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: twl4030: Fix chained irq handling on resume from suspend
mfd: arizona: Sync regcache after reset
mfd: arizona: Correctly report when AIF2/AIF1 is underclocked
mfd: arizona: Use correct array for ARRAY_SIZE in mfd_add_devices call
mfd: wm5110: Disable control interface error report for WM5110 rev B
mfd: wm5102: Update register patch for latest evaluation
mfd: twl-core: Fix chip ID for the twl6030-pwm module
With "mm: vmscan: scale number of pages reclaimed by reclaim/compaction
based on failures" reverted, Zdenek Kabelac reported the following
Hmm, so it's just took longer to hit the problem and observe
kswapd0 spinning on my CPU again - it's not as endless like before -
but still it easily eats minutes - it helps to turn off Firefox
or TB (memory hungry apps) so kswapd0 stops soon - and restart
those apps again. (And I still have like >1GB of cached memory)
kswapd0 R running task 0 30 2 0x00000000
Call Trace:
preempt_schedule+0x42/0x60
_raw_spin_unlock+0x55/0x60
put_super+0x31/0x40
drop_super+0x22/0x30
prune_super+0x149/0x1b0
shrink_slab+0xba/0x510
The sysrq+m indicates the system has no swap so it'll never reclaim
anonymous pages as part of reclaim/compaction. That is one part of the
problem but not the root cause as file-backed pages could also be
reclaimed.
The likely underlying problem is that kswapd is woken up or kept awake
for each THP allocation request in the page allocator slow path.
If compaction fails for the requesting process then compaction will be
deferred for a time and direct reclaim is avoided. However, if there
are a storm of THP requests that are simply rejected, it will still be
the the case that kswapd is awake for a prolonged period of time as
pgdat->kswapd_max_order is updated each time. This is noticed by the
main kswapd() loop and it will not call kswapd_try_to_sleep(). Instead
it will loopp, shrinking a small number of pages and calling
shrink_slab() on each iteration.
The temptation is to supply a patch that checks if kswapd was woken for
THP and if so ignore pgdat->kswapd_max_order but it'll be a hack and not
backed up by proper testing. As 3.7 is very close to release and this
is not a bug we should release with, a safer path is to revert "mm:
remove __GFP_NO_KSWAPD" for now and revisit it with the view to ironing
out the balance_pgdat() logic in general.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Zdenek Kabelac <zkabelac@redhat.com>
Cc: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Common Platform Time Sync function of the CPSW does not depend the
CPSW configuration option as it should. This patch fixes the issue by
adding the dependency.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the large buffer from the stack of the system
offset ioctl and replaces it with a kmalloced buffer.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the large buffer from the stack of the read file
operation and replaces it with a kmalloced buffer.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many new feauture have been introduced in the driver:
ethtool coalesce options, Rx HW watchdog... so this patch updates the
driver's version.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to get/set the tx/rx coalesce parameters
via ethtool interface.
Tests have been done on several platform with different GMAC chips w/o and w/
RX watchdog feature.
V2: reject coalesce settings that are not supported.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC devices newer than databook 3.40 has an embedded timer
that can be used for mitigating the number of interrupts.
So this patch adds this optimizations.
At any rate, the Rx watchdog can be disable (on bugged HW) by
passing from the platform the riwt_off field.
In this implementation the rx timer stored in the Reg9 is fixed
to the max value. This will be tuned by using ethtool.
V2: added a platform parameter to force to disable the rx-watchdog
for example on new core where it is bugged.
V3: do not disable NAPI when Rx watchdog is used.
V4: a new extra statistic field has been added to show the early
receive status in the interrupt handler.
This patch also adds an extra check to avoid to call
napi_schedule when the DMA_INTR_ENA_RIE bit is disabled in the
Interrupt Mask register.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new schema used for mitigating the
number of transmit interrupts.
It is based on a SW timer and a threshold value.
The timer is used to periodically call the stmmac_tx_clean
function; the threshold is used for setting the IC (Interrupt
on Completion bit). The ISR will then invoke the poll method.
Also the patch improves some ethtool stat fields.
V2: review the logic to manage the IC bit in the TDESC
that was bugged because it didn't take care about the
fragments. Also fix the tx_count_frames that has not to be
limited to TX DMA ring. Thanks to Ben Hutchings.
V3: removed the spin_lock irqsave/restore as D. Miller suggested.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TIMER option is not longer supported and this
code can be considered dead for this driver in
the new kernel series.
In fact, It was not updated at all and never used.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch puts the correct method name, tun_do_read, in a debug message.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 82167cb8c6 ('net: dsa/slave: Fix
compilation warnings') fixed one possible invalid configuration
(NET_DSA enabled with no trailer formats) but added others: drivers
can select NET_DSA without its dependencies being met.
It's not very useful to make either the DSA core or the tagging
formats manually selectable without a driver to use them, so:
1. Define a hidden HAVE_NET_DSA option and move the dependencies of
NET_DSA to that. While we're at it, drop the deprecated
EXPERIMENTAL dependency.
2. Make NET_DSA and the drivers dependent on HAVE_NET_DSA.
3. Hide the tagging format options again.
4. Make drivers select both NET_DSA and the appropriate tagging format
option.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb->tstamp is set to the hardware timestamp when available in the USB
urb message. This leads to user visible timestamps which contain the 'uptime'
of the USB adapter - and not the usual system generated timestamp.
Fix this wrong assignment by applying the available hardware timestamp to the
skb_shared_hwtstamps data structure - which is intended for this purpose.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The LMAC API states that the TSF clock value of
every rx'ed frame is a "usec accurate timestamp
of the hardware clock at the end of frame
(before OFDM SIFS EOF padding)".
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The vendor radiotap patch added a few fields to
struct ieee80211_rx_status that need to be zero,
initialize the struct instead of using whatever
was left on the stack.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The vendor radiotap patch added a few fields to
struct ieee80211_rx_status that need to be zero,
initialize the struct instead of using whatever
was left on the stack.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding __printf helps spot format and argument mismatches.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The frequencies will be printed when actually
doing the scan, and the IEs can be captured
on the hwsim0 monitor.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the number of channels is > 1, which means that
hwsim will use mac80211 channel contexts, it can
also advertise VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change nl80211 to support specifying a VHT (or HT)
using the control channel frequency (as before) and
new attributes for the channel width and first and
second center frequency. The old channel type is of
course still supported for HT.
Also change the cfg80211 channel definition struct
to support these by adding the relevant fields to
it (and removing the _type field.)
This also adds new helper functions:
- cfg80211_chandef_create to create a channel def
struct given the control channel and channel type,
- cfg80211_chandef_identical to check if two channel
definitions are identical
- cfg80211_chandef_compatible to check if the given
channel definitions are compatible, and return the
wider of the two
This isn't entirely complete, but that doesn't matter
until we have a driver using it. In particular, it's
missing
- regulatory checks on the usable bandwidth (if that
even makes sense)
- regulatory TX power (database can't deal with it)
- a proper channel compatibility calculation for the
new channel types
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of passing a channel pointer and channel type
to all functions and driver methods, pass a new channel
definition struct. Right now, this struct contains just
the control channel and channel type, but for VHT this
will change.
Also, add a small inline cfg80211_get_chandef_type() so
that drivers don't need to use the _type field of the
new structure all the time, which will change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.
Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avoid any possible message logging interleaving by adding
missing newlines.
Align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when none of CONFIG_NET_DSA_TAG_DSA, CONFIG_NET_DSA_TAG_EDSA and
CONFIG_NET_DSA_TAG_TRAILER is defined, we get following compilation warnings:
net/dsa/slave.c:51:12: warning: 'dsa_slave_init' defined but not used [-Wunused-function]
net/dsa/slave.c:60:12: warning: 'dsa_slave_open' defined but not used [-Wunused-function]
net/dsa/slave.c:98:12: warning: 'dsa_slave_close' defined but not used [-Wunused-function]
net/dsa/slave.c:116:13: warning: 'dsa_slave_change_rx_flags' defined but not used [-Wunused-function]
net/dsa/slave.c:127:13: warning: 'dsa_slave_set_rx_mode' defined but not used [-Wunused-function]
net/dsa/slave.c:136:12: warning: 'dsa_slave_set_mac_address' defined but not used [-Wunused-function]
net/dsa/slave.c:164:12: warning: 'dsa_slave_ioctl' defined but not used [-Wunused-function]
Earlier approach to fix this was discussed here:
lkml.org/lkml/2012/10/29/549
This is another approach to fix it. This is done by some changes in config
options, which make more sense than the earlier approach. As, atleast one
tagging option must always be selected for using net/dsa/ infrastructure, this
patch selects NET_DSA from tagging configs instead of having it as an selectable
config.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recovery doesn't work too well if we leave interrupts disabled...
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for byte queue limits on RTL8139C+
Tested on real hardware.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-By: Dave Täht <dave.taht@bufferbloat.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes (for me) a regression introduced by commit b01af457 ("8139cp:
set ring address before enabling receiver"). That commit configured the
descriptor ring addresses earlier in the initialisation sequence, in
order to avoid the possibility of triggering stray DMA before the
correct address had been set up.
Unfortunately, it seems that the hardware will scribble garbage into the
TxRingAddr registers when we enable "plus mode" Tx in the CpCmd
register. Observed on a Traverse Geos router board.
To deal with this, while not reintroducing the problem which led to the
original commit, we augment cp_start_hw() to write to the CpCmd register
*first*, then set the descriptor ring addresses, and then finally to
enable Rx and Tx in the original 8139 Cmd register. The datasheet
actually indicates that we should enable Tx/Rx in the Cmd register
*before* configuring the descriptor addresses, but that would appear to
re-introduce the problem that the offending commit b01af457 was trying
to solve. And this variant appears to work fine on real hardware.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org [3.5+]
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit b26623dab7.
This reverts the revert, in net-next we'll try another scheme
to fix this bug using patches from David Woodhouse.
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/iwlwifi/pcie/tx.c
Minor iwlwifi conflict in TX queue disabling between 'net', which
removed a bogus warning, and 'net-next' which added some status
register poking code.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86 arch fixes from Peter Anvin:
"Here is a collection of fixes for 3.7-rc7. This is a superset of
tglx' earlier pull request."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64: Fix ordering of CFI directives and recent ASM_CLAC additions
x86, microcode, AMD: Add support for family 16h processors
x86-32: Export kernel_stack_pointer() for modules
x86-32: Fix invalid stack address while in softirq
x86, efi: Fix processor-specific memcpy() build error
x86: remove dummy long from EFI stub
x86, mm: Correct vmflag test for checking VM_HUGETLB
x86, amd: Disable way access filter on Piledriver CPUs
x86/mce: Do not change worker's running cpu in cmci_rediscover().
x86/ce4100: Fix PCI configuration register access for devices without interrupts
x86/ce4100: Fix reboot by forcing the reboot method to be KBD
x86/ce4100: Fix pm_poweroff
MAINTAINERS: Update email address for Robert Richter
x86, microcode_amd: Change email addresses, MAINTAINERS entry
MAINTAINERS: Change Boris' email address
EDAC: Change Boris' email address
x86, AMD: Change Boris' email address
NAND chip detection, introduced by some rework which went into 3.7. The
initial fix wasn't quite complete, so it's in two parts. In fact the
first part is committed twice (Artem committed his own copy of the same
patch) and I've merged Artem's tree into mine which already had that fix.
I'd have recommitted that to make it somewhat cleaner, but figured by
this point in the release cycle it was better to merge *exactly* the
commits which have been in linux-next.
If I'd recommitted, I'd also omit the sparse warning fix. But it's there,
and it's harmless — just marking one function as 'static' in onenand code.
This also includes a couple more fixes for stable: an AB-BA deadlock in
JFFS2, and an invalid range check in slram.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlCwEIsACgkQdwG7hYl686NfZgCfSYFA2q8yp7jEMdDaxpFPuuDm
FFMAoI3V27BpWxRab6GylYh8erHp9ful
=Wo+T
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20121123' of git://git.infradead.org/mtd-2.6
Pull MTD fixes from David Woodhouse:
"The most important part of this is that it fixes a regression in
Samsung NAND chip detection, introduced by some rework which went into
3.7. The initial fix wasn't quite complete, so it's in two parts. In
fact the first part is committed twice (Artem committed his own copy
of the same patch) and I've merged Artem's tree into mine which
already had that fix.
I'd have recommitted that to make it somewhat cleaner, but figured by
this point in the release cycle it was better to merge *exactly* the
commits which have been in linux-next.
If I'd recommitted, I'd also omit the sparse warning fix. But it's
there, and it's harmless — just marking one function as 'static' in
onenand code.
This also includes a couple more fixes for stable: an AB-BA deadlock
in JFFS2, and an invalid range check in slram."
* tag 'for-linus-20121123' of git://git.infradead.org/mtd-2.6:
mtd: nand: fix Samsung SLC detection regression
mtd: nand: fix Samsung SLC NAND identification regression
jffs2: Fix lock acquisition order bug in jffs2_write_begin
mtd: onenand: Make flexonenand_set_boundary static
mtd: slram: invalid checking of absolute end address
mtd: ofpart: Fix incorrect NULL check in parse_ofoldpart_partitions()
mtd: nand: fix Samsung SLC NAND identification regression
Fix for an incorrect error condition check in device PM QoS code
that may lead to an Oops from Guennadi Liakhovetski.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=uXpU
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management update from Rafael Wysocki:
"Fix for an incorrect error condition check in device PM QoS code that
may lead to an Oops from Guennadi Liakhovetski."
* tag 'pm-for-3.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / QoS: fix wrong error-checking condition
- raid5 discard has problems
- raid10 replacement devices have problems
- bad block lock seqlock usage has problems
- dm-raid doesn't free everything
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=fznK
-----END PGP SIGNATURE-----
Merge tag 'md-3.7-fixes' of git://neil.brown.name/md
Pull md fixes from NeilBrown:
"Several bug fixes for md in 3.7:
- raid5 discard has problems
- raid10 replacement devices have problems
- bad block lock seqlock usage has problems
- dm-raid doesn't free everything"
* tag 'md-3.7-fixes' of git://neil.brown.name/md:
md/raid10: decrement correct pending counter when writing to replacement.
md/raid10: close race that lose writes lost when replacement completes.
md/raid5: Make sure we clear R5_Discard when discard is finished.
md/raid5: move resolving of reconstruct_state earlier in stripe_handle.
md/raid5: round discard alignment up to power of 2.
md: make sure everything is freed when dm-raid stops an array.
md: Avoid write invalid address if read_seqretry returned true.
md: Reassigned the parameters if read_seqretry returned true in func md_is_badblock.
Pull block layer fixes from Jens Axboe:
"Distilled down version of bug fixes for 3.7. The patches have been
well tested. If you notice that commit dates are from today, it's
because I pulled less important bits out and shuffled them into the
3.8 mix. Apart from that, no changes, base still the same.
It contains:
- Fix for aoe, don't run request_fn while it's plugged.
- Fix for a regression in floppy since 3.6, which causes problems if
no floppy is found.
- Stable fix for blk_exec(), don't touch a request after it has been
sent to the scheduler (and the device as well).
- Five fixes for various nasties in mtip32xx."
* 'for-linus' of git://git.kernel.dk/linux-block:
block: Don't access request after it might be freed
mtip32xx: Fix padding issue
aoe: avoid running request handler on plugged queue
mtip32xx: fix potential NULL pointer dereference in mtip_timeout_function()
mtip32xx: fix shift larger than type warning
mtip32xx: Fix incorrect mask used for erase mode
mtip32xx: Fix to make lba address correct in big-endian systems
mtip32xx: fix potential crash on SEC_ERASE_UNIT
dm: fix deadlock with request based dm and queue request_fn recursion
floppy: destroy floppy workqueue before cleaning up the queue
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1jPB
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.7-rc' of git://gitorious.org/linux-omap-dss2/linux
Pull omapdss fixes from Tomi Valkeinen:
"Here are a few OMAPDSS fixes for the next -rc. I'm sending these
directly to you, and quite late, as the fbdev tree maintainer
(Florian) has been busy with his work and hasn't had time to manage
the fb patches."
* tag 'omapdss-for-3.7-rc' of git://gitorious.org/linux-omap-dss2/linux:
OMAPDSS: do not fail if dpll4_m4_ck is missing
OMAPFB: Fix possible null pointer dereferencing
OMAPDSS: HDMI: fix missing unlock on error in hdmi_dump_regs()
omapdss: dss: Fix clocks on OMAP363x
OMAPDSS: DSI: fix dsi_get_dsidev_from_id()
Pull i2c fixes from Wolfram Sang:
"Bugfixes for the i2c subsystem.
Except for a few one-liners, there is mainly one revert because of an
overlooked dependency. Since there is no linux-next at the moment, I
did some extra testing, and all was fine for me."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Fix code to free gpios
i2c: omap: ensure writes to dev->buf_len are ordered
Revert "ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints"
i2c: at91: fix SMBus quick command
Pull networkign fixes from David Miller:
"Networking bug fixes, Cacio e Pepe edition:
1) BNX2X accidently accesses chip rev specific registers without an
appropriate guard, fix from Ariel Elior.
2) When we removed the routing cache, we set ip_rt_max_size to ~0 just
to keep reporting a value to userspace via sysfs. But the ipv4
IPSEC layer was using this to tune itself which is completely bogus
to now do. Fix from Steffen Klassert.
3) Missing initialization in netfilter ipset code from Jozsef
Kadlecsik.
4) Check CTA_TIMEOUT_NAME length properly in netfilter cttimeout code,
fix from Florian Westphal.
5) After removing the routing cache, we inadvertantly are caching
multicast routes that end up looping back locally, we cannot do
that legitimately any more. Fix from Julian Anastasov.
6) Revert a race fix for 8139cp qemu/kvm that doesn't actually work
properly on real hardware. From Francois Romieu.
7) Fixup errors in example command lines in VXLAN device docs."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
bnx2x: remove redundant warning log
vxlan: fix command usage in its doc
8139cp: revert "set ring address before enabling receiver"
ipv4: do not cache looped multicasts
netfilter: cttimeout: fix buffer overflow
netfilter: ipset: Fix range bug in hash:ip,port,net
xfrm: Fix the gc threshold value for ipv4
dev_pm_qos_add_request() can return 0, 1, or a negative error code,
therefore the correct error test is "if (error < 0)." Checking just for
non-zero return code leads to erroneous setting of the req->dev pointer
to NULL, which then leads to a repeated call to
dev_pm_qos_add_ancestor_request() in st1232_ts_irq_handler(). This in turn
leads to an Oops, when the I2C host adapter is unloaded and reloaded again
because of the inconsistent state of its QoS request list.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add information to the DMA Configuration Register to
maximize system performance:
- rx/tx packet buffer full memory size
- allow possibility to use INCR16 if supported
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Joachim Eastwood <manabian@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
this will allow to detect the link between the switch and the soc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
On BE2 chip, an interrupt being raised even when EQ is in un-armed state has
been observed a few times. This is not expected and has never been
observed on BE3/Lancer chips.
As a consequence, be_msix()::events_get() and be_poll()::events_get()
can race and notify an EQ wrongly causing a CEV UE. The other possible
side-effect would be traffic stalling because after notifying EQ,
napi_schedule() is ignored as NAPI is already running.
This patch fixes this issue by counting events only in be_poll().
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes tun_get_iff() prototype to return void as it never fails.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix bug where a register which was only meant to be read in 578xx/57712
devices causes a bogus error message to be logged when read from other
devices.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits out the logic for entering suspend modes
to separate functions, to reduce the complexity of the
smsc95xx_suspend function.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables LAN9500 family devices to wake from suspend
on either link up or link down events
It also adds _nopm versions of mdio access functions, so we can
safely call them from suspend and resume functions
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of storing the number of wake-up frame filter registers
in the pdata structure, this patch changes the driver to detect
the type of device we have and store its available features.
The new two features will be used in future patches.
This patch is intended to have no change in behaviour.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
without this patch the two lines below won't ever execute
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts b01af4579e.
The original patch was tested with emulated hardware. Real
hardware chokes.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=47041
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi Jens,
Another tiny patch.
Removed __packed before the struct smart_attr and added __packed at end of
the structure to fix padding issue.
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Calling the request handler directly on a plugged queue defeats
the performance improvements provided by the plugging mechanism.
Use the __blk_run_queue function instead of calling the request
handler directly, so that we don't interfere with the block
layer's ability to plug the queue.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The dereference to port should be moved below the NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we're building a 32-bit kernel and CONFIG_LBADF isn't set,
sector_t is 32-bits wide. The shifts by 32 and 40 are thus
larger than we support.
Cast the sector offset to a u64 to avoid these warnings.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Previous commit use value 3 for erasemode mask.
Changing the mask to correct value to 2
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Earlier lba address was assigned directly to lba_low and lba_low_ex,
which would result in a different number (bytes reversed) in
big-endian systems. Now assigning lba address byte-by-byte to fis.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The mtip driver lifted this code from elsewhere and then added a special
handling check for SEC_ERASE_UNIT. If the caller tries to do a security
erase but passes no output data for the command then outbuf is not
allocated and the driver duly explodes.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Request based dm attempts to re-run the request queue off the
request completion path. If used with a driver that potentially does
end_io from its request_fn, we could deadlock trying to recurse
back into request dispatch. Fix this by punting the request queue
run to kblockd.
Tested to fix a quickly reproducible deadlock in such a scenario.
Cc: stable@kernel.org
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull input updates from Dmitry Torokhov:
"This fixes recent regression where /dev/input/mice got assigned wrong
device node which messed up setups with static /dev, and a regression
in ads7846 GPIO debounce setup."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
ARM - OMAP: ads7846: fix pendown debounce setting
Input: ads7846 - enable pendown GPIO debounce time setting
Input: mousedev - move /dev/input/mice to the correct minor
Input: MT - document new 'flags' argument of input_mt_init_slots()
Properly terminate the DMA transfer in case the DMA PIO transfer
or setup fails for any reason.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This is a set of four bug fixes. The isci one is an obvious thinko (using
request buffer instead of response buffer) which causes a command to fail.
The three others are DIF/DIX updates which are required because they're part
of a series of ten patches, the other seven of which went into the block layer
during the merge window meaning our current DIF/DIX implementation is broken
without these three.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQre/4AAoJEDeqqVYsXL0MrxwH/A+b3aYvany+ZPg+elAFBCFm
3qHJ2Bys+M/kTkb0Fqb/l1KQfGFjooqcozm6eTgIeZ67bK947pxzu4Txy4JmeXvC
cHQ2lzEzcIFjiyVqV0tQ/wxMCnHTeqDx1WX02aw3T6e5JxObe+gC1pAEoMz2unSk
kpsSvFKBfCBMY6bmbVY5c2vpFTgD4UKtBiKn/GKtLtIDvynRx0P5e7/TNawxUB64
QZ/tu3Z2Ov5g9VWod+LpQwjVI+bIBlBEV4Of+91zou64aocrqXtSoky+ae9mwfPy
7KLLZzz5Fzc5KwT8ynEECtU2iFQXJ/zXNDRh7gBffc0ReljpuouOvIgqdZEW8d0=
=kQyb
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of four bug fixes.
The isci one is an obvious thinko (using request buffer instead of
response buffer) which causes a command to fail.
The three others are DIF/DIX updates which are required because
they're part of a series of ten patches, the other seven of which went
into the block layer during the merge window meaning our current
DIF/DIX implementation is broken without these three.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] sd: Implement support for WRITE SAME
[SCSI] sd: Permit merged discard requests
[SCSI] Add a report opcode helper
[SCSI] isci: copy fis 0x34 response into proper buffer
Pull drm fixes from Dave Airlie.
Small fixes for (mostly Nouveau, some radeon) regressions.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: use the correct fence implementation for nv50
drm/radeon: add new SI pci id
radeon: add AGPMode 1 quirk for RV250
drm/radeon: properly track the crtc not_enabled case evergreen_mc_stop()
drm/nouveau/bios: fix DCB v1.5 parsing
drm/nouveau: add missing pll_calc calls
drm/nouveau: fix crash with noaccel=1
drm/nv40: allocate ctxprog with kmalloc
drm/nvc0/disp: fix thinko in vblank regression fix..
Do not fail if dpll4_m4_ck is missing. The clock is not there on omap24xx,
so this should not be a hard error.
The patch retains the functionality before the commit 185bae10 (OMAPDSS:
DSS: Cleanup cpu_is_xxxx checks).
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
added usb-id as driver supports the stick
Signed-off-by: Andrew Karpow <andy@mailbox.tu-berlin.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new USB ID as driver supports it.
Reported-by: Hubert Lin <hubertwslin@gmail.com>
Tested-by: Hubert Lin <hubertwslin@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the MT9V022_TOTAL_SHUTTER_WIDTH register is controlled in manual
mode by V4L2_CID_EXPOSURE control, it shouldn't be written directly in
mt9v022_s_crop(). In manual mode this register should be set to the
V4L2_CID_EXPOSURE control value. Changing this register directly and
outside of the actual control function means that the register value
is not in sync with the corresponding control value. Thus, the following
problem is observed:
- setting this control initially succeeds
- VIDIOC_S_CROP ioctl() overwrites the MT9V022_TOTAL_SHUTTER_WIDTH
register
- setting this control to the same value again doesn't
result in setting the register since the control value
was previously cached and doesn't differ
Remove MT9V022_TOTAL_SHUTTER_WIDTH register setting in mt9v022_s_crop()
and add a comment explaining why it is not needed in manual mode.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the missing unlock on the error handle path in function
mx2_start_streaming().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in omap1_camera. Fix them by adjusting a function declaration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
.set_crop() implementation in mx1_camera is identical with the default.
Remove the copy to switch to using the default stab.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in mx2_camera. Fix them by cleanly separating writable and
read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in mx3_camera. Fix them by cleanly separating writable and
read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in pxa_camera.c. Fix them by adjusting a function declaration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in sh_mobile_ceu_camera. Fix them by cleanly separating writable
and read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in sh_vou. Fix them by cleanly separating writable and
read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change makes it so that only the first fragment in a series of fragments
will have the L4 header pulled. Previously we were always pulling the L4
header as well and in the case of UDP this can harm performance since only the
first fragment will have the header, the rest just contain data which should
be left in the paged portion of the packet.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Historically, we've been using the APME bit to determine whether a device
supports wake on a given port or not. However, this bit specifies the
default wake setting, rather than the wake support. Change the behavior so
that we use a flag to keep the capabilities separate from the enablement
while meeting customer requirements.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the filters to be more consistent with what the driver wants to do.
For example, for devices that timestamp all packets, report that the filter
is set for timestamping all packets.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There was a bitwise operation error in the fdb_add block
that was only allowing FDB types that were not permanent.
This was the opposite of the intent because the hardware
never ages out address these are the _only_ type of addrs
that should be allowed.
This was missed because until recently iproute2 did not
set any bit for this by default. And our test code to
manage FDB entries on embedded devices similarly did not
set these bits.
I am going to chalk this up as a bug and fix it now.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables ethtool to correctly identify flow control (pause
frame) auto negotiation, as well as disallow enabling it when it is not
supported. The ixgbe_device_supports_autoneg_fc function is exported and
used for this purpose.
There is also one minor cleanup of the device_supports_autoneg_fc by
removing an unnecessary return statement.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes the queuing that was previously done for L4 packets
as it is not needed. The filter does not provide functionality, and it
is possible that queue setup here could trample settings done else-where
in the driver. (for example it may use a queue which isn't setup.)
Setting of the queue is not required for hardware timestamping and could
have inadverdent side effects.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes a magic number that was used for the ETQF used for
filtering L2 ptp packets and replaces it with the supplied define that
previously existed. The intent is to clarify that this filter is already
set aside for L2 1588 work.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This removes an open coded simple_open() function and
replaces file operations references to the function
with simple_open() instead.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reformats the output of the Tx/Rx descriptor dumps to more
appropriately align the output of the ixgbe_dump and improve readability.
Prevents empty Tx descriptors from being displayed to decrease the size
of the dump and make it more manageable.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a write to a replacement device completes, we carefully
and correctly found the rdev that the write actually went to
and the blithely called rdev_dec_pending on the primary rdev,
even if this write was to the replacement.
This means that any writes to an array while a replacement
was ongoing would cause the nr_pending count for the primary
device to go negative, so it could never be removed.
This bug has been present since replacement was introduced in
3.3, so it is suitable for any -stable kernel since then.
Reported-by: "George Spelvin" <linux@horizon.com>
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
When a replacement operation completes there is a small window
when the original device is marked 'faulty' and the replacement
still looks like a replacement. The faulty should be removed and
the replacement moved in place very quickly, bit it isn't instant.
So the code write out to the array must handle the possibility that
the only working device for some slot in the replacement - but it
doesn't. If the primary device is faulty it just gives up. This
can lead to corruption.
So make the code more robust: if either the primary or the
replacement is present and working, write to them. Only when
neither are present do we give up.
This bug has been present since replacement was introduced in
3.3, so it is suitable for any -stable kernel since then.
Reported-by: "George Spelvin" <linux@horizon.com>
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Alex writes:
A couple more small fixes for 3.7:
- another evergreen_mc fix
- add an AGP quirk for an old RV250
- new pci id.
* 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add new SI pci id
radeon: add AGPMode 1 quirk for RV250
drm/radeon: properly track the crtc not_enabled case evergreen_mc_stop()
nouveau: one more regression fix.
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: use the correct fence implementation for nv50
Some more misc fallout from nouveau rework.
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/bios: fix DCB v1.5 parsing
drm/nouveau: add missing pll_calc calls
drm/nouveau: fix crash with noaccel=1
drm/nv40: allocate ctxprog with kmalloc
drm/nvc0/disp: fix thinko in vblank regression fix..
Only compile time tested, noticed nv50_fence_create was never used,
so fix this. This will probably fix vblank on nv50 cards.
Hopefully this is still in time for 3.7 final release.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The commit 81732c3b2f
("Fix line garbage in virtual console on command line edition")
made a regression with some machines: some characters were not erased
after line edition.
This patch adjusts the number of moved characters and the size of the
region to be updated.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Tested-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking updates from David Miller:
1) inet6_csk_update_pmtu() must return NULL or non-NULL, so translate
ERR_PTR to NULL, as needed. Fix from Eric Dumazet.
2) Fix copy&paste error in IRDA sir_dev ->set_speed method invocation,
it was testing the NULL'ness of a different method to guard the
call. Fix from Alexander Shiyan.
3) Fix build regression of xilinx driver, from Jeff Mahoney.
4) Make XEN netfront (like XEN netback) handle compound pages in SKBs
properly. From Ian Campbell.
5) Fix inverted logic of team_dev_queue_xmit() return value checks,
from Jiri Pirko and Dan Carpenter.
6) dma_poll_create() no longer allows a NULL device argument, breaking
both ixp4xx drivers. Fix from Xi Wang.
7) ne2000 driver doesn't hook up the parent device properly, breaking
udev matching. Fix from Alan Cox.
8) Locking and memory leak fixes in Near Field Communications layer.
From Thierry Escande, Szymon Janc, and Waldemar Rymarkiewicz.
9) sis900 resume regression, sis900_set_mode() is being called with the
iomem pointer instead of the expected device private. Fix from
Francois Romieu.
10) Fix IBSS regression caused by uninitializing the ibss-internals
before performing an emptyness check, from Simon WUnderlich.
11) Fix SNIFFER mode regression in iwlwifi driver, from Johannes Berg.
12) Fix task wedges in mwifiex_cmd_timeout_func(), from Bing Zhao.
13) Add back wireless sysfs directory, too much stuff depends upon it
being there (actually I'd say it never should have been removed to
begin with). From Johannes Berg.
14) Fix hang introduced by suspend/resume changes in ath9k. Fix from
Sujith Manoharan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (24 commits)
team: bcast: convert return value of team_dev_queue_xmit() to bool correctly
bonding: Bonding driver does not consider the gso_max_size/gso_max_segs setting of slave devices.
xen/netfront: handle compound page fragments on transmit
net: fix build failure in xilinx
irda: sir_dev: Fix copy/paste typo
ipv6: fix inet6_csk_update_pmtu() return value
ixp4xx_hss: avoid calling dma_pool_create() with NULL dev
ixp4xx_eth: avoid calling dma_pool_create() with NULL dev
ne2000: add the right platform device
of/net/mdio-gpio: Fix pdev->id issue when using devicetrees.
NFC: Fix pn533 target mode memory leak
NFC: pn533: Fix mem leak in pn533_in_dep_link_up
NFC: pn533: Fix use after free
NFC: pn533: Fix missing lock while operating on commands list
NFC: Fix nfc_llcp_local chained list insertion
ath9k_hw: Fix regression in device reset
sis900: fix sis900_set_mode call parameters.
iwlwifi: don't WARN when a non empty queue is disabled
wireless: add back sysfs directory
mwifiex: report error to MMC core if we cannot suspend
...
commit 9e44476851
MD: raid5 avoid unnecessary zero page for trim
change raid5 to clear R5_Discard when the complete request is
handled rather than when submitting the per-device discard request.
However it did not clear R5_Discard for the parity device.
This means that if the stripe_head was reused before it expired from
the cache, the setting would be wrong and a hang would result.
Also if the R5_Uptodate bit happens to be set, R5_Discard again
won't be cleared. But R5_Uptodate really should be clear at this point.
So make sure R5_Discard is cleared in all cases, and clear
R5_Uptodate when a 'discard' completes.
Signed-off-by: NeilBrown <neilb@suse.de>
stripe_handle.
The chunk of code in stripe_handle which responds to a
*_result value in reconstruct_state is really the completion
of some processing that happened outside of handle_stripe
(possibly asynchronously) and so should be one of the first
things done in handle_stripe().
After the next patch it will be important that it happens before
handle_stripe_clean_event(), as that will clear some dev->flags
bit that this code tests.
Signed-off-by: NeilBrown <neilb@suse.de>
Some platforms need the pendown GPIO debounce time setting programmed.
Since the pendown GPIO is handled by the driver, the debounce time
should also be handled along with the pendown GPIO request.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The STDI block may measure wrong values, especially for lcvs and lcf. If the
driver can not find any valid timing, the STDI block is restarted to measure
the video timings again. The function will return an error, but the restart of
STDI will generate a new STDI interrupt and the format detection process will
restart.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use predefined video timings (prim_mode/vid_std) when available as recommended
by Analog Devices (http://ez.analog.com/message/48267#48267).
Also remove 720p30 support since the ADV7604 can't handle that.
(http://ez.analog.com/message/61488#61488)
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
CC drivers/net/wireless/rtlwifi/rtl8723ae/trx.o
drivers/net/wireless/rtlwifi/rtl8723ae/trx.c: In function ‘rtl8723ae_rx_query_desc’:
drivers/net/wireless/rtlwifi/rtl8723ae/trx.c:324:21: error: ‘RX_FLAG_MACTIME_MPDU’ undeclared (first use in this function)
drivers/net/wireless/rtlwifi/rtl8723ae/trx.c:324:21: note: each undeclared identifier is reported only once for each function it appears in
make[3]: *** [drivers/net/wireless/rtlwifi/rtl8723ae/trx.o] Error 1
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changes the way the primary mode is handled:
- Remove it from platform_data since it doesn't belong there.
- Add a new mode enum for use with s_routing.
- Collapse the two HDMI modes into one HDMI mode: when setting up the
timings manually we do not need to select HDMI_COMP mode. That's only
needed when selecting a preset.
This patch prepares for the next step where we switch to using the presets
where available.
Signed-off-by: Mats Randgaard <mats.randgaard@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
One of the debug macro invocations ended up with a stray 0 argument
where the format string should be. Remove it.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes sparse warning:
drivers/net/wireless/brcm80211/brcmsmac/main.c:308:10: sparse: symbol 'wlc_prio2prec_map' was not declared. Should it be static?
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'stations' debugfs file has multiple issues. It doesn't scale
to an arbitrary number of associated stations and allocating
64K is not elegant either. Now that changes have been made in
mac80211 to support dynamic creation/deletion of driver-specific
debugfs files on station addition/removal, remove this file and
make use of the mac80211 hooks (which will be done in a sebsequent
patch).
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the rate statistics only when debugfs has been enabled
in ath9k and mac80211 and move the stat() functions under proper
conditionals.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the rate control statistics debugfs file properly
via remove_sta_debugfs(). Also, check for both MAC80211_DEBUGFS
and ATH9K_DEBUGFS config options.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'xmit' debugfs file has become big and unwieldy, fix
multiple issues with its usage:
* Store TX counters/statistics only for the 4 Access Categories.
Use IEEE80211_NUM_ACS instead of ATH9K_NUM_TX_QUEUES.
* Move various utility macros to debug.h, they can be reused
elsewhere.
* Remove tx_complete_poll_work_seen.
* Remove code that accesses various internal queue-specific
variables without any locking whatsoever. HW/SW queue details
will be handled in a subsequent patch.
* Do not print internal values like txq_headidx and txq_headidx.
They were mostly unused anyway, considering code like:
PRX("txq_tailidx: ", txq_headidx);
* Handle 'txprocdesc' for EDMA too.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the macros provided by mac80211 and remove redundant
declarations inside the drivers.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move regulatory domain initialization code to a separate function.
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On lower WLAN signal strength, WLAN downlink traffic might suffer
from retransmissions. At the mean time, playing SCO/A2DP profiles
is affecting WLAN stability. In such scenario, by stomping SCO/A2DP
BT traffic completely for a BTCOEX period, gives WLAN traffic an
oppertunity to recover PHY rate. It also improves WLAN stability at
lower RSSI without sacificing BT traffic.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reverts the commit "ath9k_hw: Wait BT calibration to complete"
and bail out from MCI interrupt routine for chip reset. The above commit
stalls the WLAN TCP traffic while bringing up and down the BT interface
iteratively. Fixing this properly by queueing up chip reset and bailing
out properly from tasklet routine.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
FATAL and WATCHDOG interrupts should be processed first followed
by others.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The thing is that team_dev_queue_xmit() returns NET_XMIT_* or -E*.
bc_trasmit() should return true in case all went well. So use ! to get
correct retval from team_dev_queue_xmit() result.
This bug caused iface statistics to be badly computed.
This bug was introduced by:
team: add broadcast mode (5fc889911a)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch sets the lowest gso_max_size and gso_max_segs values of the slave devices during enslave and detach.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An SKB paged fragment can consist of a compound page with order > 0.
However the netchannel protocol deals only in PAGE_SIZE frames.
Handle this in xennet_make_frags by iterating over the frames which
make up the page.
This is the netfront equivalent to 6a8ed462f1 for netback.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: netdev@vger.kernel.org
Cc: xen-devel@lists.xen.org
Cc: Eric Dumazet <edumazet@google.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: ANNIE LI <annie.li@oracle.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: Stefan Bader <stefan.bader@canonical.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This is a batch of fixes intended for 3.7...
Included are two pulls. Regarding the mac80211 tree, Johannes says:
"Please pull my mac80211.git tree (see below) to get two more fixes for
3.7. Both fix regressions introduced *before* this cycle that weren't
noticed until now, one for IBSS not cleaning up properly and the other
to add back the "wireless" sysfs directory for Fedora's startup scripts."
Regarding the iwlwifi tree, Johannes says:
"Please also pull my iwlwifi.git tree, I have two fixes: one to remove a
spurious warning that can actually trigger in legitimate situations, and
the other to fix a regression from when monitor mode was changed to use
the "sniffer" firmware mode."
Also included is an nfc tree pull. Samuel says:
"We mostly have pn533 fixes here, 2 memory leaks and an early unlocking fix.
Moreover, we also have an LLCP adapter linked list insertion fix."
On top of that, a few more bits... Albert Pool adds a USB ID
to rtlwifi. Bing Zhao provides two mwifiex fixes -- one to fix
a system hang during a command timeout, and the other to properly
report a suspend error to the MMC core. Finally, Sujith Manoharan
fixes a thinko that would trigger an ath9k hang during device reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The irqs are enabled one-by-one in pm core resume_noirq phase.
This leads to situation where the twl4030 primary interrupt
handler (PIH) is enabled before the chained secondary handlers
(SIH). As the PIH cannot clear the pending interrupt, and
SIHs have not been enabled yet, a flood of interrupts hangs
the device.
Fixed the issue by setting the SIH irqs with IRQF_EARLY_RESUME
flags, so they get enabled before the PIH.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@jollamobile.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some fixes and a MAINTAINERS update to remove my lost AMD email address
from the file. The fixes take care of a resource leak and a problem on
VT-d with the new IOMMU group code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RZ+1
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v3.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"Some fixes and a MAINTAINERS update to remove my lost AMD email
address from the file. The fixes take care of a resource leak and a
problem on VT-d with the new IOMMU group code."
* tag 'iommu-fixes-v3.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
intel-iommu: Fix lookup in add device
iommu/tegra-smmu.c: fix dentry reference leak in smmu_debugfs_stats_show().
iommu/amd: Update MAINTAINERS entry
This is a regression introduced by ceb90fa0 (xen/privcmd: add
PRIVCMD_MMAPBATCH_V2 ioctl). It broke xentrace as it used
xc_map_foreign() instead of xc_map_foreign_bulk().
Most code-paths prefer the MMAPBATCH_V2, so this wasn't very obvious
that it broke. The return value is set early on to -EINVAL, and if all
goes well, the "set top bits of the MFN's" never gets called, so the
return value is still EINVAL when the function gets to the end, causing
the caller to think it went wrong (which it didn't!)
Now also including Andres "move the ret = -EINVAL into the error handling
path, as this avoids other similar errors in future.
Signed-off-by: Mats Petersson <mats.petersson@citrix.com>
Acked-by: Andres Lagar-Cavilla <andres@lagarcavilla.org>
Acked-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Commit 71c6c837 (drivers/net: fix tasklet misuse issue) introduced a
build failure in the xilinx driver. axienet_dma_err_handler isn't
declared before its use in axienet_open.
This patch provides the prototype before axienet_open.
Cc: Xiaotian Feng <dannyfeng@tencent.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use &port->netdev->dev instead of NULL since dma_pool_create() doesn't
allow NULL dev.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use &port->netdev->dev instead of NULL since dma_pool_create() doesn't
allow NULL dev.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids build failures on some architectures...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
These messages clutter up the trace buffer without adding any useful
information.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the brcmsmac_tx trace system for tx debugging. Existing code to dump
tx status and descriptors are converted to using tracepoints, allowing
for more efficient collection and post-processing of this data. These
tracepoints are placed to collect data for all tx frames instead of only
on errors. Logging of tx errors is also improved.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also convert relevant messages to use this macro.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also convert relevant messages to use this macro.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also convert relevant message to use this macro.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also convert relevant messages over to use thses macros.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This macro is used for messages related to the 802.11 MAC layer.
Relevant messages are also converted to use this macro.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert most uses of wiphy_* and pr_* for general error and debug
messages to use the internal debug macros instead. Most code used only
for initialization still use wiphy_err(), as well as some locations
which are executed too early to use the debug macros. Some debug
messages which are redundant or not useful are removed.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new brcmsmac_msg trace system to enable writing of debug messages
to the trace buffer, and add brcms_* macros for storing device debug
messages in the trace buffer in addition to the printk log buffer.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debug level can be set by passing debug=... to brcmsmac whenever
CONFIG_BRCMDBG is enabled.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation for enhancements to debug and trace support, convert the
message levels to debug levels which will be used for enabling
categories of debug messages. The two message levels are little-used
anyway and are combined into the BRCM_DL_INFO debug level.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the runtime overhead of trace support is small when tracing is
disabled, users may be interested in turning on trace support while
leaving other debug features off. Add a new config option named
CONFIG_BRCM_TRACING for this purpose.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently up to 256 frames can be queued for each DMA ring. This is
excessive, and now that we have better flow control we can get by with
less. Experimentation has shown 64 to work well.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nextrxd() is calling txd(), which means that the tx descriptor count is
used to determine when to wrap for determining the next ring buffer
entry. This has worked so far since the driver has been using the same
number of rx and tx descriptors, but it's obviously going to be a
problem if different numbers of descriptors are used.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcmsmac internal tx buffering is problematic. The amount of
buffering is excessive (228 packets in addition to the 256 slots in each
DMA ring), and frames may be dropped due to a lack of flow control.
This patch reworks the transmit code path to remove the internal
buffering. Frames are immediately handed off to the DMA support rather
than passing through an intermediate queue. Non-aggregate frames are
queued immediately into the tx rings, and aggregate frames are queued
temporarily in an AMPDU session until ready for transmit.
Transmit flow control is also added to avoid dropping packets when the
tx rings are full. Conceptually this is a separate change, but it's
included in this commit because removing the tx queue without adding
flow control could cause significant problems.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 tx queues and brcmsmac DMA fifos both map directly to AC
levels. Therefore it's much more straightforward to queue tx frames and
choose the tx fifo based on the mac80211 queue instead of mapping 802.1D
priority tags to precedence levels then back to AC levels. mac80211
already maps the 802.1D levels to the appropriate AC levels and queues
management frames at the maximum priority, so the results should be
identical.
One functional change resulting from this patch is that AMPDU retries no
longer get a priority boost to queue them ahead of packets with the same
priority already in the tx queue. This behavior will be restored (in
effect at least) in a later patch when the tx queue is removed.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Functions for flow control exist but remain unimplemented. Remove these
in advance of adding real flow control.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use this helper function rather than open-coding the same calculation in
multiple places.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to the comments this "reduces rate lag," but in reality the
only way this value is used is for determining whether or not any frames
remain to be transmitted. Therefore there's no reason for AMPDU packets
to receive any weighting.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AMPDU session allows MPDUs to be temporarily queued until either a full
AMPDU has been collected or circumstances dictate that transmission
should start with a partial AMPDU. Packets are added to the session by
calling brcms_c_ampdu_add_frame(). brcms_c_ampdu_finalize() should be
called to fix up the tx headers in the first and last packet before
adding the packets to the DMA ring. brmcs_c_sendampdu() is converted to
using AMPDU sessions.
This patch has no real value on it's own, but is needed in preparation
for elimination of the tx packet queue from brcmsmac.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without this udev doesn't have a way to key the ne device to the platform
device.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides extensions to VXLAN for supporting Distributed
Overlay Virtual Ethernet (DOVE) networks. The patch includes:
+ a dove flag per VXLAN device to enable DOVE extensions
+ ARP reduction, whereby a bridge-connected VXLAN tunnel endpoint
answers ARP requests from the local bridge on behalf of
remote DOVE clients
+ route short-circuiting (aka L3 switching). Known destination IP
addresses use the corresponding destination MAC address for
switching rather than going to a (possibly remote) router first.
+ netlink notification messages for forwarding table and L3 switching
misses
Changes since v2
- combined bools into "u32 flags"
- replaced loop with !is_zero_ether_addr()
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Intel 82855PM host bridge / Mobility FireGL 9000 RV250 combination
in an (outdated) ThinkPad T41 needs AGPMode 1 for suspend/resume (under
KMS, that is). So add a quirk for it.
(Change R250 to RV250 in comment for preceding quirk too.)
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The save struct is not initialized previously so explicitly
mark the crtcs as not used when they are not in use.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
In the absence of a physical reset line the chip is reset by writing the
first register, which is done after the register patch has been applied.
This patch synchronises the register cache after the reset to preserve
any register changes that had been applied.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In the interrupt handler for an underclocked event, whilst checking for
the source of the interrupt, AIF3 was checked twice and AIF1 was not
checked. This change correctly checks the AIF1 underclocked bit and
reports the correct error messages for all cases.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
wm5102_devs array was used for ARRAY_SIZE whilst adding the wm5110
devices. This change corrects this to get the size from the wm5110_devs
array. As both arrays are the same size no issues should have been
caused by this bug.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Latest evaluation of the device has provided some revisions to the
configuration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The correct chip id is 1 since the PWM module is on address 0x49. With the
current TWL6030_MODULE_ID1 the kernel will crash early since we have:
#define TWL6030_MODULE_ID1 0x0E
and
static struct twl_client twl_modules[4];
Down in the stack we try to get the module by:
struct twl_client *twl = &twl_modules[chip];
Which is obviously going to do nasty things.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
blkdev_issue_discard currently assumes that the granularity
is a power of 2. So in raid5, round the chosen number up to
avoid embarrassment.
Cc: Shaohua Li <shli@kernel.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Various drivers depend on INET because they used to select INET_LRO,
but they have all been converted to use GRO which has no such
dependency.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2cb1deb56f ('ehea: Remove LRO
support') left behind the Kconfig depends/select and feature flag.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fa37a9586f ('mlx4_en: Moving to
work with GRO') left behind the Kconfig depends/select, some dead
code and comments referring to LRO.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ndo_validate_addr is set to the generic eth_validate_addr
function there is no point in calling is_valid_ether_addr
from driver ndo_open if ndo_open is not used elsewhere in
the driver.
With this change is_valid_ether_addr will be called from the
generic eth_validate_addr function. So there should be no change
in the actual behavior.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mdio-gpio driver is probed via device trees, the platform
device id is set as -1, However the pdev->id is re-used as bus-id for
while creating mdio gpio bus.
So
For device tree case the mdio-gpio bus name appears as "gpio-ffffffff"
where as
for non-device tree case the bus name appears as "gpio-<bus-num>"
Which means the bus_id is fixed in device tree case, so we can't have
two mdio gpio buses via device trees. Assigning a logical bus number
via device tree solves the problem and the bus name is much consistent
with non-device tree bus name.
Without this patch
1. we can't support two mdio-gpio buses via device trees.
2. we should always pass gpio-ffffffff as bus name to phy_connect, very
different to non-device tree bus name.
So, setting up the bus_id via aliases from device tree is the right
solution and other drivers do similar thing.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
md_stop() would stop an array, but not free various attached
data structures.
For internal arrays, these are freed later in do_md_stop() or
mddev_put(), but they don't apply for dm-raid arrays.
So get md_stop() to free them, and only all it from dm-raid.
For internal arrays we now call __md_stop.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If read_seqretry returned true and bbp was changed, it will write
invalid address which can cause some serious problem.
This bug was introduced by commit v3.0-rc7-130-g2699b67.
So fix is suitable for 3.0.y thru 3.6.y.
Reported-by: zhuwenfeng@kedacom.com
Tested-by: zhuwenfeng@kedacom.com
Cc: stable@vger.kernel.org
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This bug was introduced by commit(v3.0-rc7-126-g2230dfe).
So fix is suitable for 3.0.y thru 3.6.y.
Cc: stable@vger.kernel.org
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In target mode, sent sk_buff were not freed in pn533_tm_send_complete
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
cmd is allocated in pn533_dep_link_up and passed as an arg to
pn533_send_cmd_frame_async together with a complete cb.
arg is passed to the cb and must be kfreed there.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
cmd was freed in pn533_dep_link_up regardless of
pn533_send_cmd_frame_async return code. Cmd is passed as argument to
pn533_in_dep_link_up_complete callback and should be freed there.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In pn533_wq_cmd command was removed from list without cmd_lock held
(race with pn533_send_cmd_frame_async) which could lead to list
corruption. Delete command from list before releasing lock.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Akinobu Mita
Jiri Bohac
zheng.li
David S. Miller
Marc Kleine-Budde
Alexander Stein
Linus Torvalds
Mugunthan V N
Ben Hutchings
Jiri Pirko
Dan Carpenter
Sathya Perla
Paul Bolle
Michal Kubeček
Michael S. Tsirkin
Bjørn Mork
Steve Glendinning
Amir Vadai
Sony Chacko
Yaniv Rosner
John W. Linville
Don Skidmore
Greg Rose
Parikh, Neerav
Alexander Duyck
Matthew Vick
Mitch A Williams
Andreas Larsson
Olivier Sobrie
AnilKumar Ch
Mel Gorman
Richard Cochran
Giuseppe CAVALLARO
Rami Rosen
Oliver Hartkopp
Christian Lamparter
Johannes Berg
Joe Perches
Shahed Shaikh
viresh kumar
David Woodhouse
Guennadi Liakhovetski
Nicolas Ferre
Jean-Christophe PLAGNIOL-VILLARD
Ariel Elior
françois romieu
Selvan Mani
Ed Cashin
Wei Yongjun
Jens Axboe
Jiri Kosina
Marek Vasut
Aaro Koskinen
Andrew Karpow
Antti Palosaari
Anatolij Gustschin
John Fastabend
Jacob Keller
Josh Hay
NeilBrown
Dave Airlie
Maarten Lankhorst
Jean-François Moine
Igor Grinberg
Hans Verkuil
Seth Forshee
Sujith Manoharan
Stanislav Yakovlev
Rajkumar Manoharan
Sarveshwar Bandi
Ian Campbell
Kalle Jokiniemi
David Woodhouse
Emmanuel Grumbach
Mats Petersson
Jeff Mahoney
Alexander Shiyan
Xi Wang
Alan Cox
Sachin Kamat
David Stevens
Alex Deucher
Charles Keepax
Mark Brown
Peter Ujfalusi
Joachim Eastwood
Srinivas Kandagatla
majianpeng
Thierry Escande
Waldemar Rymarkiewicz
Szymon Janc