Commit Graph

11 Commits

Author SHA1 Message Date
Bruno Randolf c0e1899bdb ath5k: always extend rx timestamp with tsf
always extend the rx timestamp with the local TSF, since this information is
also needed for proper IBSS merging. this is done in the tasklet for now, maybe
has to be moved to the interrupt handler like in madwifi.

drivers/net/wireless/ath5k/base.c:      Changes-licensed-under: 3-Clause-BSD

Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:10:54 -08:00
Bruno Randolf 6d91e1d808 ath5k: configure backoff for IBSS beacon queue
in "11.1.2.2 Beacon generation in an IBSS" the IEEE802.11 standard says, each
STA should... "b) Calculate a random delay uniformly distributed in the range
between zero and twice aCWmin × aSlotTime,".

configure cwmin and cwmax of the beacon queue in IBSS mode according to this.
unfortunately beacon backoff does not work reliably yet, so i suspect we have a
problem somewhere else, since the same settings (and similar beacon timer
configuration) work for madwifi.

drivers/net/wireless/ath5k/base.c:      Changes-licensed-under: 3-Clause-BSD

Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:10:53 -08:00
Bruno Randolf 036cd1ec03 ath5k: use SWBA to detect IBSS HW merges
use SWBA (software beacon alert) interrupts to keep track of the next beacon
time und check if a HW merge (automatic TSF update) has happened on every
received beacon with the same BSSID.

this is necessary because the atheros hardware will silently update the local
TSF in IBSS mode, but not its beacon timers. if the TSF is ahead of the beacon
timers no beacons are sent until the timers wrap around (typically after about
1 minute).

this solution is not very nice, since we have to look into every beacon, but
there is apparently no other way to detect HW merges.

drivers/net/wireless/ath5k/base.c:      Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/base.h:      Changes-licensed-under: 3-Clause-BSD

Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:10:52 -08:00
Bruno Randolf 9804b98d57 ath5k: better beacon timer calculation
update ath5k_beacon_update_timers() for better beacon timer calculation in a
variety of situations. most important is the possibility to call it with the
timestamp of a received beacon, when we detected that a HW merge has happened
and we need to reconfigure the beacon timers based on that.

we call this from the mac80211 callback reset_tsf now instead of beacon_update,
and there will be more use of it in the next patch.

drivers/net/wireless/ath5k/base.c:      Changes-licensed-under: 3-Clause-BSD

Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:10:51 -08:00
Bruno Randolf e535c1ac7e ath5k: beacon interval is in TU
the beacon interval is passed by mac80211 in TU already, so we can directly use
it without conversion. also update the comments about TU (1 TU is defined by
802.11 as 1024usec).

drivers/net/wireless/ath5k/ath5k.h:     Changes-licensed-under: ISC
drivers/net/wireless/ath5k/base.c:      Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/base.h:      Changes-licensed-under: 3-Clause-BSD

Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:10:50 -08:00
Bruno Randolf 1008e0f7b9 ath5k: use 3 instead of 0x00000003
reviewed beacon timer initialization with register traces from madwifi: what we
are doing is correct :). one minor fix: use 3 instead of 0x00000003 - it's more
readable.

drivers/net/wireless/ath5k/hw.c:        Changes-licensed-under: ISC

Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:10:50 -08:00
John W. Linville 247ae44920 ath5k: reset key cache after resume
Otherwise it may be impossible to connected to an open network after a
resume.

This is a modified version of an original patch by
Alex Eskin <alexeskin@yahoo.com>:

	https://bugzilla.redhat.com/show_bug.cgi?id=425950#c8

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:10:48 -08:00
John W. Linville c65638a72c ath5k: use AR5K_KEYTABLE_SIZE when initializing key table
...instead of using AR5K_KEYCACHE_SIZE, which would seem to be a
typo/thinko...

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:10:47 -08:00
Luis R. Rodriguez 132127e505 ath5k: Fix frame duration oops
This patch fixes an oops which was introduced as a regression by
commit fd640775bd16e1df50c867cc547af0, on the patch titled,
"mac80211: dont use interface indices in drivers".

ieee80211_generic_frame_duration() now relies on sdata->flags which
itself gets set upon bringing the interface up. We check for the
virtual interface now before setting the rate duration registers.

After the mode changes are introduced onto mac80211 we should revisit
these changes.

This patch was tested on the following cards:

1) BG card:

Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43)
RF2112A 2GHz radio found (0x46)

2) ABG card:

Atheros AR5213A chip found (MAC: 0x59,PHY: 0x43)
RF5112A multiband radio found (0x36)

Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:09:40 -08:00
Johannes Berg 32bfd35d4b mac80211: dont use interface indices in drivers
This patch gets rid of the if_id stuff where possible in favour of
a new per-virtual-interface structure "struct ieee80211_vif". This
structure is located at the end of the per-interface structure and
contains a variable length driver-use data area.

This has two advantages:
 * removes the need to look up interfaces by if_id, this is better
   for working with network namespaces and performance
 * allows drivers to store and retrieve per-interface data without
   having to allocate own lists/hash tables

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:09:36 -08:00
Jiri Slaby fa1c114fda [PATCH] Net: add ath5k wireless driver
add ath5k wireless driver

Portions of this driver are covered by one or both of the ISC and
3-clause BSD licenses.  Specific license information is cited at the top
of each file.

Acked-by and Signed-off-by information is collected from individual
patches as collected in the wireless-2.6 tree prior to upstream
submission.

Acked-by: Matthew W. S. Bell  <mentor@madwifi.org>
Acked-by: Michael Taylor <mike.taylor@apprion.com>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bradley M. Kuhn <bkuhn@softwarefreedom.org>
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Francesco Gringoli <francesco.gringoli@ing.unibs.it>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Karen Sandler <karen@softwarefreedom.org>
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: Matt Norwood <norwood@softwarefreedom.org>
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Richard Fontana <fontana@softwarefreedom.org>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Ulrich Meis <meis@nets.rwth-aachen.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-28 15:09:35 -08:00