The only way for p_set to be NULL would be if vin_coef_set would be an
empty array.
On such case, the driver will OOPS, as it would try to de-reference a
NULL value. So, the check if p_set is not NULL doesn't make any sense.
Solves those two smatch warnings:
drivers/media/platform/rcar-vin/rcar-dma.c:489 rvin_set_coeff() warn: variable dereferenced before check 'p_set' (see line 484)
drivers/media/platform/rcar-vin/rcar-dma.c:494 rvin_set_coeff() error: we previously assumed 'p_set' could be null (see line 489)
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the operation in rvin_set_channel_routing() is successful the 'ret'
variable contains the runtime PM use count for the VIN master device.
The intention is not to return the use count to the caller but to return
0 on success else none zero.
Fix this by always returning 0 if the operation is successful.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Kconfig and Makefile doesn't have license line, thus,
these are GPL-2.0 as default.
All ohter files are GPL-2.0+ as original license.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Handle data-enable signal polarity. If the polarity is not specifically
requested to be active low, use the active high default.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Media bus configuration flags and media bus type were so far a property
of each VIN instance, as the subdevice they were connected to was
immutable during the whole system life time.
With the forth-coming introduction of parallel input devices support,
a VIN instance can have the subdevice it is connected to switched at
runtime, from a CSI-2 subdevice to a parallel one and viceversa, through
the modification of links between media entities in the media controller
graph. To avoid discarding the per-subdevice configuration flags retrieved by
v4l2_fwnode parsing facilities, cache them in the 'rvin_graph_entity'
member of each VIN instance, opportunely renamed to 'rvin_parallel_entity'.
Also modify the register configuration function to take mbus flags into
account when running on a bus type that supports them.
The media bus type currently in use will be updated in a follow-up patch
to the link state change notification function.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As the term 'digital' is used all over the rcar-vin code in place of
'parallel', rename all the occurrencies.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When starting the VIN capture procedure we are not guaranteed that the
first buffer written to is VnMB1 to which we assigned the first buffer
queued. This is problematic for two reasons. Buffers might not be
dequeued in the same order they where queued for capture. Future
features planed for the VIN driver is support for outputting frames in
SEQ_TB/BT format and to do that it's important that capture starts from
the first buffer slot, VnMB1.
We are guaranteed that capturing always happens in sequence (VnMB1 ->
VnMB2 -> VnMB3 -> VnMB1). So drop up to two frames when starting
capturing so that the driver always returns buffers in the same order
they are queued and prepare for SEQ_TB/BT output.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The offending commit was an attempt to fix the issue of writing outside
the capture buffer for VIN Gen3. Unfortunately it only fixed the symptom
of the problem to such a degree I could no longer reproduce it. Revert
the offending commit before a proper fix can be added in a follow-up
patch.
This reverts commit 015060cb77.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The VIN Gen3 hardware don't have Line Post-Clip capabilities as VIN Gen2
hardware have. To protect against writing outside the capture window
enable field toggle after a set number of lines have been captured.
Capturing outside the allocated capture buffer where observed on R-Car
Gen3 Salvator-XS H3 from the CVBS input if the standard is
misconfigured. That is if a PAL source is connected to the system but
the adv748x standard is set to NTSC. In this case the format reported by
the adv748x is 720x480 and that is what is used for the media pipeline.
The PAL source generates frames in the format of 720x576 and the field
is not toggled until the VSYNC is detected and at that time data have
already been written outside the allocated capture buffer.
With this change the capture in the situation described above results in
garbage frames but that is far better then writing outside the capture
buffer.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
By setting VNMC_YCAL rcar-vin can support input video in
MEDIA_BUS_FMT_UYVY8_1X16 format.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The procedure to start or stop streaming using the non-MC single
subdevice and the MC graph and multiple subdevices are quite different.
Create a new function to abstract which method is used based on which
mode the driver is running in and add logic to start the MC graph.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the driver runs in media controller mode it should not directly
control the subdevice instead userspace will be responsible for
configuring the pipeline. To be able to run in this mode a different set
of v4l2 operations needs to be used.
Add a new set of v4l2 operations to support operation without directly
interacting with the source subdevice.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On Gen3 the CSI-2 routing is controlled by the VnCSI_IFMD register. One
feature of this register is that it's only present in the VIN0 and VIN4
instances. The register in VIN0 controls the routing for VIN0-3 and the
register in VIN4 controls routing for VIN4-7.
To be able to control routing from a media device this function is need
to control runtime PM for the subgroup master (VIN0 and VIN4). The
subgroup master must be switched on before the register is manipulated,
once the operation is complete it's safe to switch the master off and
the new routing will still be in effect.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the register needed to work with Gen3 hardware. This patch adds
the logic for how to work with the Gen3 hardware. More work is required
to enable the subdevice structure needed to configure capturing.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Bus configuration will once the driver is extended to support Gen3
contain information not specific to only the directly connected parallel
subdevice. Move it to struct rvin_dev to show it's not always coupled
to the parallel subdevice.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
At stream on time the driver should not query the subdevice for which
standard are used. Instead it should be cached when userspace sets the
standard and used at stream on time.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There was never proper support in the VIN driver to deliver ALTERNATING
field format to user-space, remove this field option. The problem is
that ALTERNATING field order requires the sequence numbers of buffers
returned to userspace to reflect if fields were dropped or not,
something which is not possible with the VIN drivers capture logic.
The VIN driver can still capture from a video source which delivers
frames in ALTERNATING field order, but needs to combine them using the
VIN hardware into INTERLACED field order. Before this change if a source
was delivering fields using ALTERNATE the driver would default to
combining them using this hardware feature. Only if the user explicitly
requested ALTERNATE field order would incorrect frames be delivered.
The height should not be cut in half for the format for TOP or BOTTOM
fields settings. This was a mistake and it was made visible by the
scaling refactoring. Correct behavior is that the user should request a
frame size that fits the half height frame reflected in the field
setting. If not the VIN will do its best to scale the top or bottom to
the requested format and cropping and scaling do not work as expected.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The logic to preserve the requested format width and height are too
complex and come from a premature optimization for Gen3. All Gen2 SoC
can scale and the Gen3 implementation will not use these functions at
all so simply preserve the width and height when interacting with the
subdevice much like the field is preserved simplifies the logic quite a
bit.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation of refactoring the scaling code move the code regarding
scaling to to the top of the file to avoid the need to add forward
declarations. No code is changed in this commit only whole functions
moved inside the same file.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The functions to register and unregister the hardware and video device
where poorly named from the start. Rename them to better describe their
intended function.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of switching capture mode depending on how many buffers are
available use a scratch buffer and always run in continuous mode. By
using a scratch buffer the responsiveness of the capture loop is
increased as it can keep running even if there are no buffers available
from userspace.
As soon as a userspace queues a buffer it is inserted into the capture
loop and returned as soon as it is filled. This is a improvement on the
previous logic where the whole capture loop was stopped and switched to
single capture mode if userspace did not feed the VIN driver buffers at
the same time it consumed them. To make matters worse it was difficult
for the driver to reenter continuous mode if it entered single mode even
if userspace started to queue buffers faster. This resulted in
suboptimal performance where if userspace where delayed for a short
period the ongoing capture would be slowed down and run in single mode
until the capturing process where restarted.
An additional effect of this change is that the capture logic can be
made much simple as we know that continuous mode will always be used.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Before starting a capture, allocate a scratch buffer which can be used
by the driver to give to the hardware if no buffers are available from
userspace. The buffer is not used in this patch but prepares for future
refactoring where the scratch buffer can be used to avoid the need to
fallback on single capture mode if userspace can't queue buffers as fast
as the VIN driver consumes them.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of using a custom driver implementation, use
v4l2_async_notifier_parse_fwnode_endpoints() to parse the fwnode endpoints
of the device.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
With the driver stopping and starting the stream each time the driver is
stalled rvin_capture_off() can be folded in to the only caller.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If userspace can't feed the driver with buffers as fast as the driver
consumes them the driver will stop video capturing and wait for more
buffers from userspace, the driver is stalled. Once it have been feed
one or more free buffers it will recover from the stall and resume
capturing.
Instead of continue to capture using the same capture mode as before the
stall allow the driver to choose between single and continuous mode
based on free buffer availability. Do this by stopping capturing when
the driver becomes stalled and restart capturing once it continues. By
doing
this the capture mode will be evaluated each time the driver is
recovering from a stall.
This behavior is needed to fix a bug where continuous capturing mode is
used, userspace is about to stop the stream and is waiting for the last
buffers to be returned from the driver and is not queuing any new
buffers. In this case the driver becomes stalled when there are only 3
buffers remaining streaming will never resume since the driver is
waiting for userspace to feed it more buffers before it can continue
streaming. With this fix the driver will then switch to single capture
mode for the last 3 buffers and a deadlock is avoided. The issue can be
demonstrated using yavta.
$ yavta -f RGB565 -s 640x480 -n 4 --capture=10 /dev/video22
Device /dev/video22 opened.
Device `R_Car_VIN' on `platform:e6ef1000.video' (driver 'rcar_vin') supports video, capture, without mplanes.
Video format set: RGB565 (50424752) 640x480 (stride 1280) field interlaced buffer size 614400
Video format: RGB565 (50424752) 640x480 (stride 1280) field interlaced buffer size 614400
4 buffers requested.
length: 614400 offset: 0 timestamp type/source: mono/EoF
Buffer 0/0 mapped at address 0xb6cc7000.
length: 614400 offset: 614400 timestamp type/source: mono/EoF
Buffer 1/0 mapped at address 0xb6c31000.
length: 614400 offset: 1228800 timestamp type/source: mono/EoF
Buffer 2/0 mapped at address 0xb6b9b000.
length: 614400 offset: 1843200 timestamp type/source: mono/EoF
Buffer 3/0 mapped at address 0xb6b05000.
0 (0) [-] interlaced 0 614400 B 38.240285 38.240303 12.421 fps ts mono/EoF
1 (1) [-] interlaced 1 614400 B 38.282329 38.282346 23.785 fps ts mono/EoF
2 (2) [-] interlaced 2 614400 B 38.322324 38.322338 25.003 fps ts mono/EoF
3 (3) [-] interlaced 3 614400 B 38.362318 38.362333 25.004 fps ts mono/EoF
4 (0) [-] interlaced 4 614400 B 38.402313 38.402328 25.003 fps ts mono/EoF
5 (1) [-] interlaced 5 614400 B 38.442307 38.442321 25.004 fps ts mono/EoF
6 (2) [-] interlaced 6 614400 B 38.482301 38.482316 25.004 fps ts mono/EoF
7 (3) [-] interlaced 7 614400 B 38.522295 38.522312 25.004 fps ts mono/EoF
8 (0) [-] interlaced 8 614400 B 38.562290 38.562306 25.003 fps ts mono/EoF
<blocks forever, waiting for the last buffer>
This fix also allow the driver to switch to single capture mode if
userspace doesn't feed it buffers fast enough. Or the other way around,
if userspace suddenly feeds the driver buffers faster it can switch to
continues capturing mode.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of selecting single or continuous capture mode based on how many
buffers userspace intends to give us select capture mode based on number
of free buffers we can allocate to hardware when the stream is started.
This change is a prerequisite to enable the driver to switch from
continuous to single capture mode (or the other way around) when the
driver is stalled by userspace not feeding it buffers as fast as it
consumes it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This only moves whole structs, defines and functions around, no code is
changed inside any function. The reason for moving this code around is
to prepare for refactoring and fixing of a start/stop stream bug without
having to use forward declarations.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It's possible to grab frames using only one buffer, this should never
have been set to anything else then 1.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The HW can capture both ODD and EVEN fields in separate buffers so it's
possible to support V4L2_FIELD_ALTERNATE. This patch add support for
this mode.
At probe time and when S_STD is called the driver will default to use
V4L2_FIELD_INTERLACED if the subdevice reports V4L2_FIELD_ALTERNATE. The
driver will only change the field type if the subdevice implements
G_STD, if not it will keep the default at V4L2_FIELD_ALTERNATE.
The user can always explicitly ask for V4L2_FIELD_ALTERNATE in S_FMT and
the driver will use that field format.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The field V4L2_FIELD_INTERLACED is standard dependent and should not
unconditionally be equivalent to V4L2_FIELD_INTERLACED_TB.
This patch adds a check to see if the video standard can be obtained and
if it's a 60 Hz format. If the condition is met V4L2_FIELD_INTERLACED
is treated as V4L2_FIELD_INTERLACED_BT if not as
V4L2_FIELD_INTERLACED_TB.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The media bus format reported by the adv7180 is wrong. Steve Longerbeam
posted a patch which changed the format to UYVY8_2X8 with the commit
message:
Change the media bus format from YUYV8_2X8 to UYVY8_2X8. Colors
now look correct when capturing with the i.mx6 backend. The other
option is to set the SWPC bit in register 0x27 to swap the Cr and Cb
output samples.
The rcar-vin driver was developed and tested with the adv7180 and
therefor suffers from the same issue, looking for the wrong media bus
format. The two errors corrected each other.
This patch takes Steve's patch and merge it with a fix for rcar-vin
driver. The rcar-vin driver is used used in together with the adv7180
och Koelsch and this ensures it will not break while fixing the adv7180
issue. I checked wit Steve and he was fine with me merging the patches.
ADV7180 parts:
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Suggested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for vb2_ops structures that are only stored in the ops field of a
vb2_queue structure. That field is declared const, so vb2_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct vb2_ops i@p = { ... };
@ok@
identifier r.i;
struct vb2_queue e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct vb2_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct vb2_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
[hans.verkuil@cisco.com: dropped soc_camera/rcar_vin.c patch because that driver will be removed]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The primary reason for this change is to prepare for Gen3 support where
there will be more then one possible video source. Each source will have
its own media bus format and code, so it needs to be moved from the per
device structure to a structure used to represent an individual
connection to a video source.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The check for if the specific pixelformat is supported on the current
chip should happen in VIDIOC_S_FMT and VIDIOC_TRY_FMT and not when we
try to setup the hardware for streaming.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this a proper typed array. Drop the old allocate context code since
that is no longer used.
Note that the memops functions now get a struct device pointer instead of
the struct device ** that was there initially (actually a void pointer to
a struct containing only a struct device pointer).
This code is now a lot cleaner.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Stop using alloc_ctx and just fill in the device pointer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A V4L2 driver for Renesas R-Car VIN driver that do not depend on
soc_camera. The driver is heavily based on its predecessor and aims to
replace it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Mauro Carvalho Chehab
Niklas Söderlund
Kuninori Morimoto
Jacopo Mondi
Sakari Ailus
Julia Lawall
Hans Verkuil