The commit
05fed81625 ("[media] marvell-ccic: add MIPI support for marvell-ccic driver")
that claimed to add CSI2 turned on C0_EOF_VSYNC for parallel bus
without a very good explanation.
That broke camera on OLPC XO-1.75 which precisely uses a sensor on a
parallel bus. Revert that chunk.
Tested on an OLPC XO-1.75.
Fixes: 05fed81625 ("[media] marvell-ccic: add MIPI support for marvell-ccic driver")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The commit d790b7eda9 ("[media] vb2-dma-sg: move dma_(un)map_sg here")
left dma_desc_nent unset. It previously contained the number of DMA
descriptors as returned from dma_map_sg().
We can now (since the commit referred to above) obtain the same value from
the sg_table and drop dma_desc_nent altogether.
Tested on OLPC XO-1.75 machine. Doesn't affect the OLPC XO-1's Cafe
driver, since that one doesn't do DMA.
[mchehab+samsung@kernel.org: fix a checkpatch warning]
Fixes: d790b7eda9 ("[media] vb2-dma-sg: move dma_(un)map_sg here")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Due to limitations in gpiolib it was impossible to disable the interrupt of
an input gpio and then switch it to gpio output and drive it. The only way
to achieve that was to free the interrupt first, then switch the direction.
When going back to gpio input and using interrupts to read the gpio pin you
had to request the irq again.
This limitation was lifted in gpiolib in kernel 4.20, but the cec-gpio driver
was still using the old workaround implementation.
This patch updates the cec-gpio driver to just enable and disable the irq.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Venus v4 doesn't send ALLOC_MODE property and thus parser doesn't
recognize it as dynamic buffer (for OUTPUT/OUTPUT2 type of buffers)
make it obvious in the helper function.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Patch commit de5a0bafcf ("media: venus: core: correct maximum hardware
load for sdm845") meant to increase the maximum hardware load for sdm845,
but ended up changing the one for msm8996 instead.
Fixes: de5a0bafcf ("media: venus: core: correct maximum hardware load for sdm845")
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The header report return value from decoder sequence initialization is
available on CodaHx4 and CODA7541 already. Use the profile and level
identification values reported by the firmware to update codec specific
profile and level controls after sequence initialization has succeeded.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When a menu control is updated via s_ctrl, print the corresponding menu
entry string in addition to the numerical value it is set to.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Otherwise the default initialization would always swamp the debug log.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Print a single line containing the following information:
- which frame was decoded, including its type,
- if no frame was decoded, the reason (code) why
- which decoded frame was returned, copied out by either rotator or VODA,
- if no frame was returned, the reason (code) why, and
- the output queue sequence number, which is only useful in case
each queued coded buffer corresponds to exactly one frame.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a function to translate from V4L2 buffer flags to 'I'/'P'/'B'
characters for debug output.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This allows to use coda_debug level 2 for verbose but not quite as
verbose debug logging. Register access level logging is of limited
use anyway, as this includes busy polling of status bits.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case the sensor refuses to set the format, avoid printing the error
message that no compatible format was found.
This means that the try_fmt will be less verbose.
The error will be printed only if really a format cannot be found.
Some application try all possible formats in a row (gstreamer e.g.)
which will flood the console with error messages until a working one is found.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds support for the 'button' control DO_WHITE_BALANCE
This feature will enable the ISC to compute the white balance coefficients
in a one time shot, at the user discretion.
This can be used if a color chart/grey chart is present in front of the camera.
The ISC will adjust the coefficients and have them fixed until next balance
or until sensor mode is changed.
This is particularly useful for white balance adjustment in different
lighting scenarios, and then taking photos to similar scenery.
The old auto white balance stays in place, where the ISC will adjust every
4 frames to the current scenery lighting, if the scenery is approximately
grey in average, otherwise grey world algorithm fails.
One time white balance adjustments needs streaming to be enabled, such that
capture is enabled and the histogram has data to work with.
Histogram without capture does not work in this hardware module.
To start the one time white balance procedure:
v4l2-ctl --set-ctrl=do_white_balance=1
This feature works only if the sensor is streaming RAW data, as the hardware
supports a histogram only for RAW bayer components.
If the auto white balance is enabled, do_white_balance does nothing.
If the streaming is disabled, or the sensor does not output RAW data, the
control is inactive.
User controls now include the do_white_balance ctrl:
User Controls
brightness 0x00980900 (int) : min=-1024 max=1023 step=1 default=0 value=0 flags=slider
contrast 0x00980901 (int) : min=-2048 max=2047 step=1 default=256 value=256 flags=slider
white_balance_automatic 0x0098090c (bool) : default=1 value=0
do_white_balance 0x0098090d (button) : flags=write-only, execute-on-write
gamma 0x00980910 (int) : min=0 max=2 step=1 default=2 value=2 flags=slider
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reworked auto white balance feature (awb) to cope with all four channels.
Implemented stretching and grey world algorithms.
Using the histogram, the ISC will auto adjust the white balance during
frame captures.
Because each histogram needs a frame, it will take 4 frames for one adjustment.
When the gains were updated by previous code, the registers for the gains
were updated only on new streaming start. Now, after each full histogram the
registers are updated with new gains.
Also, on previous code, if the streaming stopped but not all 3 histograms
finished, a new histogram was started either way. This used to lead to an
error "timeout to update profile" when streaming was stopped.
According to the hardware, histogram can only work together with the capture,
not independently.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the Kbuild core manipulates header search paths in a crazy
way [1].
To fix this mess, I want all Makefiles to add explicit $(srctree)/ to
the search paths in the srctree. Some Makefiles are already written in
that way, but not all. The goal of this work is to make the notation
consistent, and finally get rid of the gross hacks.
Having whitespaces after -I does not matter since commit 48f6e3cf5b
("kbuild: do not drop -I without parameter").
[1]: https://patchwork.kernel.org/patch/9632347/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=M94t
-----END PGP SIGNATURE-----
Merge tag 'media/v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Some fixes for some platform drivers (rockchip, atmel, omap, daVinci,
tegra-cec, coda and rcar).
Also includes a fix on one of the V4L2 uAPI doc, explaining a border
case"
* tag 'media/v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: rockchip/vpu: Fix/re-order probe-error/remove path
media: rockchip/vpu: Initialize mdev->bus_info
media: rockchip/vpu: Get vdev from the file arg in vidioc_querycap()
media: rockchip/vpu: Add missing dont_use_autosuspend() calls
media: rockchip/vpu: Do not request id 0 for our video device
media: tegra-cec: fix cec_notifier_parse_hdmi_phandle return check
media: davinci/vpbe: array underflow in vpbe_enum_outputs()
media: field-order.rst: clarify FIELD_ANY and FIELD_NONE
media: staging/imx: add media device to capture register
media: rcar-csi2: Propagate the FLD signal for NTSC and PAL
media: rcar-csi2: restart CSI-2 link if error is detected
media: omap_vout: potential buffer overflow in vidioc_dqbuf()
media: coda: fix unset field and fail on invalid field in buf_prepare
media: atmel: atmel-isc: fix asd memory allocation
media: atmel: atmel-isc: fix INIT_WORK misplacement
media: atmel: atmel-isc: limit incoming pixels per frame
-----BEGIN PGP SIGNATURE-----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=YFiQ
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-05-09' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This has two exciting community drivers for ARM Mali accelerators.
Since ARM has never been open source friendly on the GPU side of the
house, the community has had to create open source drivers for the
Mali GPUs. Lima covers the older t4xx and panfrost the newer 6xx/7xx
series. Well done to all involved and hopefully this will help ARM
head in the right direction.
There is also now the ability if you don't have any of the legacy
drivers enabled (pre-KMS) to remove all the pre-KMS support code from
the core drm, this saves 10% or so in codesize on my machine.
i915 also enable Icelake/Elkhart Lake Gen11 GPUs by default, vboxvideo
moves out of staging.
There are also some rcar-du patches which crossover with media tree
but all should be acked by Mauro.
Summary:
uapi changes:
- Colorspace connector property
- fourcc - new YUV formts
- timeline sync objects initially merged
- expose FB_DAMAGE_CLIPS to atomic userspace
new drivers:
- vboxvideo: moved out of staging
- aspeed: ASPEED SoC BMC chip display support
- lima: ARM Mali4xx GPU acceleration driver support
- panfrost: ARM Mali6xx/7xx Midgard/Bitfrost acceleration driver support
core:
- component helper docs
- unplugging fixes
- devm device init
- MIPI/DSI rate control
- shmem backed gem objects
- connector, display_info, edid_quirks cleanups
- dma_buf fence chain support
- 64-bit dma-fence seqno comparison fixes
- move initial fb config code to core
- gem fence array helpers for Lima
- ability to remove legacy support code if no drivers requires it (removes 10% of drm.ko size)
- lease fixes
ttm:
- unified DRM_FILE_PAGE_OFFSET handling
- Account for kernel allocations in kernel zone only
panel:
- OSD070T1718-19TS panel support
- panel-tpo-td028ttec1 backlight support
- Ronbo RB070D30 MIPI/DSI
- Feiyang FY07024DI26A30-D MIPI-DSI panel
- Rocktech jh057n00900 MIPI-DSI panel
i915:
- Comet Lake (Gen9) PCI IDs
- Updated Icelake PCI IDs
- Elkhartlake (Gen11) support
- DP MST property addtions
- plane and watermark fixes
- Icelake port sync and VEBOX disable fixes
- struct_mutex usage reduction
- Icelake gamma fix
- GuC reset fixes
- make mmap more asynchronous
- sound display power well race fixes
- DDI/MIPI-DSI clocks for Icelake
- Icelake RPS frequency changing support
- Icelake workarounds
amdgpu:
- Use HMM for userptr
- vega20 experimental smu11 support
- RAS support for vega20
- BACO support for vega12 + fixes for vega20
- reworked IH interrupt handling
- amdkfd RAS support
- Freesync improvements
- initial timeline sync object support
- DC Z ordering fixes
- NV12 planes support
- colorspace properties for planes=
- eDP opts if eDP already initialized
nouveau:
- misc fixes
etnaviv:
- misc fixes
msm:
- GPU zap shader support expansion
- robustness ABI addition
exynos:
- Logging cleanups
tegra:
- Shared reset fix
- CPU cache maintenance fix
cirrus:
- driver rewritten using simple helpers
meson:
- G12A support
vmwgfx:
- Resource dirtying management improvements
- Userspace logging improvements
virtio:
- PRIME fixes
rockchip:
- rk3066 hdmi support
sun4i:
- DSI burst mode support
vc4:
- load tracker to detect underflow
v3d:
- v3d v4.2 support
malidp:
- initial Mali D71 support in komeda driver
tfp410:
- omap related improvement
omapdrm:
- drm bridge/panel support
- drop some omap specific panels
rcar-du:
- Display writeback support"
* tag 'drm-next-2019-05-09' of git://anongit.freedesktop.org/drm/drm: (1507 commits)
drm/msm/a6xx: No zap shader is not an error
drm/cma-helper: Fix drm_gem_cma_free_object()
drm: Fix timestamp docs for variable refresh properties.
drm/komeda: Mark the local functions as static
drm/komeda: Fixed warning: Function parameter or member not described
drm/komeda: Expose bus_width to Komeda-CORE
drm/komeda: Add sysfs attribute: core_id and config_id
drm: add non-desktop quirk for Valve HMDs
drm/panfrost: Show stored feature registers
drm/panfrost: Don't scream about deferred probe
drm/panfrost: Disable PM on probe failure
drm/panfrost: Set DMA masks earlier
drm/panfrost: Add sanity checks to submit IOCTL
drm/etnaviv: initialize idle mask before querying the HW db
drm: introduce a capability flag for syncobj timeline support
drm: report consistent errors when checking syncobj capibility
drm/nouveau/nouveau: forward error generated while resuming objects tree
drm/nouveau/fb/ramgk104: fix spelling mistake "sucessfully" -> "successfully"
drm/nouveau/i2c: Disable i2c bus access after ->fini()
drm/nouveau: Remove duplicate ACPI_VIDEO_NOTIFY_PROBE definition
...
cec_notifier_parse_hdmi_phandle returns an error pointer, not a NULL
pointer on error.
Fixes: 4d34c9267db7: ("media: tegra_cec: use new cec_notifier_parse_hdmi_phandle helper")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In vpbe_enum_outputs() we check if (temp_index >= cfg->num_outputs) but
the problem is that "temp_index" can be negative. This patch changes
the types to unsigned to address this array underflow bug.
Fixes: 66715cdc32 ("[media] davinci vpbe: VPBE display driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Depending on which video standard is used the driver needs to setup the
hardware to correctly handle fields. If stream is identified as NTSC
or PAL setup field detection and propagate the field detection signal.
Later versions of the datasheet have been updated to make it clear
that FLD register should be set to 0 when dealing with non-interlaced
field formats.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Restart the CSI-2 link if the CSI-2 receiver detects an error during
reception. The driver did nothing when a link error happened and the
data flow simply stopped without the user knowing why.
Change the driver to try and recover from errors by restarting the link
and informing the user that something is not right. For obvious reasons
it's not possible to recover from all errors (video source disconnected
for example) but in such cases the user is at least informed of the
error and the same behavior of the stopped data flow is retained.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The "b->index" is a u32 the comes from the user in the ioctl. It hasn't
been checked. We aren't supposed to use it but we're instead supposed
to use the value that gets written to it when we call videobuf_dqbuf().
The videobuf_dqbuf() first memsets it to zero and then re-initializes it
inside the videobuf_status() function. It's this final value which we
want.
Hans Verkuil pointed out that we need to check the return from
videobuf_dqbuf(). I ended up doing a little cleanup related to that as
well.
Fixes: 72915e851d ("[media] V4L2: OMAP: VOUT: dma map and unmap v4l2 buffers in qbuf and dqbuf")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance likes to queue a buffer with field set to V4L2_FIELD_ANY
and expects it to be returned corrected to a valid field.
Follow vicodec in handling this in the buf_prepare callback.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The subsystem will free the asd memory on notifier cleanup, if the asd is
added to the notifier.
However the memory is freed using kfree.
Thus, we cannot allocate the asd using devm_*
This can lead to crashes and problems.
To test this issue, just return an error at probe, but cleanup the
notifier beforehand.
Fixes: 106267444f ("[media] atmel-isc: add the Image Sensor Controller code")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case the completion function failes, unbind will be called
which will call cancel_work for awb_work.
This will trigger a WARN message from the workqueue.
To avoid this, move the INIT_WORK call at the start of the completion
function. This way the work is always initialized, which corresponds
to the 'always canceled' unbind code.
Fixes: 93d4a26c3d ("[media] atmel-isc: add the isc pipeline function")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This will limit the incoming pixels per frame from the sensor.
Currently, the ISC will stop sampling the frame only when the vsync/hsync
are detected.
If we misconfigure the resolution in the sensor w.r.t. resolution in the ISC,
the buffer used for DMA in the ISC will be smaller than the number of pixels
that the ISC DMA engine will copy.
In this case it happens that the DMA will overwrite parts of the memory which
should not be written, leading to memory corruption.
To avoid this situation, use the PFE CFG1 and PFE CFG2 registers, which crop
the incoming frame to the resolution that we configure.
This way the DMA engine will never write more data than we expect it to.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reserved memory doesn't need to be required; system memory would work
fine.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The reset line is toggled by enabling the clocks, so it's not necessary
to manually toggle the reset as well.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
During probe, return the provided errors value instead of -ENODEV.
This allows the driver to be deferred probed if needed.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the V4L2_PIX_FMT_RGBA555, V4L2_PIX_FMT_RGBX555,
V4L2_PIX_FMT_ABGR555, V4L2_PIX_FMT_XBGR555, V4L2_PIX_FMT_BGRA555 and
V4L2_PIX_FMT_BGRX555 formats to the VSP driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the V4L2_PIX_FMT_RGBA444, V4L2_PIX_FMT_RGBX444,
V4L2_PIX_FMT_ABGR444, V4L2_PIX_FMT_XBGR444, V4L2_PIX_FMT_BGRA444 and
V4L2_PIX_FMT_BGRX444 formats to the VSP driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the V4L2_PIX_FMT_BGRA32, V4L2_PIX_FMT_BGRX32,
V4L2_PIX_FMT_RGBA32 and V4L2_PIX_FMT_RGBX32 formats to the VSP driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Amlogic G12A SoC embeds a second CEC controller with a totally
different design.
The two controller can work in the same time since the CEC line can
be set to two different pins on the two controllers.
This second CEC controller is documented as "AO-CEC-B", thus the
registers will be named "CECB_" to differentiate with the other
AO-CEC driver.
Unlike the other AO-CEC controller, this one takes the Oscillator
clock as input and embeds a dual-divider to provide a precise
32768Hz clock for communication. This is handled by registering
a clock in the driver.
Unlike the other AO-CEC controller, this controller supports setting
up to 15 logical addresses and supports the signal_free_time settings
in the transmit function.
Unfortunately, this controller does not support "monitor" mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CrosEC CEC driver never decremented the HDMI device refcount.
CEC drivers only need the HDMI device pointer as a key in the
notifier list, it never accesses the device, so there is no
need to keep a reference.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The SECO CEC driver never decremented the HDMI device refcount.
CEC drivers only need the HDMI device pointer as a key in the
notifier list, it never accesses the device, so there is no
need to keep a reference.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Tegra CEC driver increased the HDMI device refcount when
it shouldn't. Use the new helper function to ensure that that
doesn't happen and to simplify the driver code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The STI CEC driver increased the HDMI device refcount when
it shouldn't. Use the new helper function to ensure that that
doesn't happen and to simplify the driver code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The S5P CEC driver increased the HDMI device refcount when
it shouldn't. Use the new helper function to ensure that that
doesn't happen and to simplify the driver code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The meson CEC driver increased the HDMI device refcount when
it shouldn't. Use the new helper function to ensure that that
doesn't happen and to simplify the driver code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
I previously added an RC_CORE dependency here, but missed the corner
case of CONFIG_VIDEO_SECO_CEC=y with CONFIG_RC_CORE=m, which still
causes a link error:
drivers/media/platform/seco-cec/seco-cec.o: In function `secocec_probe':
seco-cec.c:(.text+0x1b8): undefined reference to `devm_rc_allocate_device'
seco-cec.c:(.text+0x2e8): undefined reference to `devm_rc_register_device'
drivers/media/platform/seco-cec/seco-cec.o: In function `secocec_irq_handler':
seco-cec.c:(.text+0xa2c): undefined reference to `rc_keydown'
Refine the dependency to disallow building the RC subdriver in this case.
This is the same logic we apply in other drivers like it.
Fixes: f27dd0ad68 ("media: seco-cec: fix RC_CORE dependency")
Cc: <stable@vger.kernel.org> # 5.1
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Later datasheet versions (rev 1.00) clarifies that the FLD register
should be set after LINKCNT.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Latest information from hardware engineers reveals that H3 ES2 and ES3
behave differently when working with link speeds bellow 250 Mpbs.
Add a SoC match for H3 ES2.* and use the correct startup sequence.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The latest datasheet (rev 1.50) updates the start procedure for V3M and
E3. Update the driver to match these changes.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Later versions of the datasheet updates the reset procedure to more
closely resemble the standby mode. Update the driver to enter and exit
the standby mode instead of resetting the hardware before and after
streaming is started and stopped. This replaces the software reset
(SRST.SRST) control.
While at it break out the full start and stop procedures from
rcsi2_s_stream() into the existing helper functions.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If VIDIOC_CREATE_BUFS is called with a sizeimage smaller than the
queue sizeimage, fail with -EINVAL instead of correcting the size
and continuing without error. This is required by v4l2-compliance.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance sets colorimetry on the output queue and then verifies
that querying colorimetry on the capture queue returns the same
configuration. For this to work, the encoder must allow setting context
colorimetry parameters on the output queue.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The stateful encoder API requires VIDIOC_ENUM_FRAMESIZES to be
implemented.
Allow enumeration of supported frame sizes for encoding.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Return -ENOTTY when userspace tries to call VIDIOC_(TRY_)ENCODER_CMD on
a decoder instance or VIDIOC_(TRY_)DECODER_CMD on an encoder instance.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add min number of buffers for capture (decoder) and output (encoder)
controls, which are required by the stateful video decoder / encoder
interface specification.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The error return value is not written by some firmware codecs, such as
MPEG-2 decode on CodaHx4. Clear the error return value before starting
the picture run to avoid misinterpreting unrelated values returned by
sequence initialization as error return value.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since levels are specified in terms of maximum values, there is no
reason to filter out lower levels than the supported maximum.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The chosen codec depends on the coded format, which is known as soon as
the S_FMT call on the coded queue. This allows to use the codec in
callbacks that may be called before start_streaming, such as buf_queue.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
syzkaller reported crashes on kfree() called from
vivid_vid_cap_s_selection(). This looks like a simple typo, as
dev->bitmap_cap is allocated with vzalloc() throughout the file.
Fixes: ef834f7836 ("[media] vivid: add the video capture and output
parts")
Signed-off-by: Alexander Potapenko <glider@google.com>
Reported-by: Syzbot <syzbot+6c0effb5877f6b0344e2@syzkaller.appspotmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Update referenced frame buffer's reference count when playing vp9
content which has show_existing_frame flag, and copy enough buffer
data to current shown frame.
Signed-off-by: Maoguang Meng <maoguang.meng@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Do not access sd_formats[] if num_of_sd_formats is zero, ie
subdev sensor didn't expose any formats.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Report overrun error only when it exceeds a given threshold.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Enlarge the plane number to support more complex case
and add the support for fmt change case.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Media bus codes were being mapped to pixelformats, which causes a
limitation on vimc because not all pixelformats can be mapped to media
bus codes.
Also, media bus codes are an internal configuration from the device.
Userspace only assures media bus codes matches between pads and expects
the image in a given pixelformat. So we can allow almost any media bus
format to be configured between pads, except for debayer that expects a
media bus code of type bayer in the sink pad.
[hverkuil-cisco@xs4all.nl: drop use of v4l2_get_fourcc_name: not yet available]
[hverkuil-cisco@xs4all.nl: made vimc_mbus_list static]
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is mandatory to write CEC_CFGR only when CECEN=0. To protect
transmission, a check have been added to delayed logical address
modification. This patch is necessary tp pass all tests of compliance.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
ISC will output the "ARGB32" configuration in byte order: B, G, R, Alpha.
This is in fact the format BGRA, aka ABGR32.
If alpha is missing, the same format is equivalent to XBGR32.
Added both formats and removed ARGB32 which is wrong.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This change is a redesign in the formats and the way the ISC is
configured w.r.t. sensor format and the output format from the ISC.
I have changed the splitting between sensor output (which is also ISC input)
and ISC output.
The sensor format represents the way the sensor is configured, and what ISC
is receiving.
The format configuration represents the way ISC is interpreting the data and
formatting the output to the subsystem.
Now it's much easier to figure out what is the ISC configuration for input, and
what is the configuration for output.
The non-raw format can be obtained directly from sensor or it can be done
inside the ISC. The controller format list will include a configuration for
each format.
The old supported formats are still in place, if we want to dump the sensor
format directly to the output, the try format routine will detect and
configure the pipeline accordingly.
This also fixes the previous issues when the raw format was NULL which
resulted in many crashes for sensors which did not have the expected/tested
formats.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The strncpy() function is being deprecated upstream. Replace
it by the safer strscpy().
While here, replace a few occurences of strlcpy() that were
recently added to also use strscpy().
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The support for those two formats are archtecture-dependent.
Use the endianness to CPU macros to do it right.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
devm_kcalloc may fail and return a null pointer. The fix returns
-ENOMEM upon failures to avoid null pointer dereferences.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This member is never read throughout the code, so remove it.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 0650a91499 ("media: mtk-vcodec: Correct return type for mem2mem
buffer helpers") fixed the return types for mem2mem buffer helper
functions by changing a few local variables from vb2_buffer to
vb2_v4l2_buffer. However, it left a few accesses to vb2_buffer::planes
as-is, accidentally turning them into accesses to
vb2_v4l2_buffer::planes and resulting in values being read from/written
to the wrong place.
Fix this by inserting vb2_buf into these accesses so they mimic their
original behavior.
Fixes: 0650a91499 ("media: mtk-vcodec: Correct return type for mem2mem buffer helpers")
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
clang warns about a possible variable use that gcc never
complained about:
drivers/media/platform/davinci/isif.c:982:32: error: variable 'frame_size' is uninitialized when used here
[-Werror,-Wuninitialized]
dm365_vpss_set_pg_frame_size(frame_size);
^~~~~~~~~~
drivers/media/platform/davinci/isif.c:887:2: note: variable 'frame_size' is declared here
struct vpss_pg_frame_size frame_size;
^
1 error generated.
There is no initialization for this variable at all, and there
has never been one in the mainline kernel, so we really should
not put that stack data into an mmio register.
On the other hand, I suspect that gcc checks the condition
more closely and notices that the global
isif_cfg.bayer.config_params.test_pat_gen flag is initialized
to zero and never written to from any code path, so anything
depending on it can be eliminated.
To shut up the clang warning, just remove the dead code manually,
it has probably never been used because any attempt to do so
would have resulted in undefined behavior.
Fixes: 63e3ab142f ("V4L/DVB: V4L - vpfe capture - source for ISIF driver on DM365")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Smatch warns about small size on two structs:
drivers/media/platform/qcom/venus/hfi_parser.c:103 parse_profile_level() error: memcpy() 'proflevel' too small (8 vs 128)
drivers/media/platform/qcom/venus/hfi_parser.c: drivers/media/platform/qcom/venus/hfi_parser.c:129 parse_caps() error: memcpy() 'cap' too small (16 vs 512)
The reason is that the hfi_parser actually expects:
- multiple data entries on hfi_capabilities
- multiple profile_level on hfi_profile_level_supported
However, the structs trick gcc, making it to believe that
there's just one value for each.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The only way for p_set to be NULL would be if vin_coef_set would be an
empty array.
On such case, the driver will OOPS, as it would try to de-reference a
NULL value. So, the check if p_set is not NULL doesn't make any sense.
Solves those two smatch warnings:
drivers/media/platform/rcar-vin/rcar-dma.c:489 rvin_set_coeff() warn: variable dereferenced before check 'p_set' (see line 484)
drivers/media/platform/rcar-vin/rcar-dma.c:494 rvin_set_coeff() error: we previously assumed 'p_set' could be null (see line 489)
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
At the error logic, ipc_buf was already asigned to &ctx->ipc_buf_struct,
with can't be null, as warned by smatch:
drivers/media/platform/sti/delta/delta-ipc.c:223 delta_ipc_open() warn: variable dereferenced before check 'ctx->ipc_buf' (see line 183)
So, remove the uneeded check.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Indentation is odd in several places, especially when printing messages
to the kernel log. Fix it to match the usual coding style.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
for stateless decoder, set the output pixelformat
to V4L2_PIX_FMT_FWHT_STATELESS and the pix info to
pixfmt_stateless_fwht
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Implement a stateless decoder for the new node.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: add 'return 0;' before default case in vicodec_try_ctrl()]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add stateless decoder instance field to the dev struct and
register another node for the statelsess decoder.
The stateless API for the node will be implemented in further patches.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix typo: videdev-stateless-dec -> stateless-decoder]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add structs and definitions needed to implement stateless
decoder for fwht and add I/P-frames QP controls to the
public api.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add struct 'vicodec_dev_instance' for the fields in vicodec_dev
that have have both decoder and encoder versions.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the stateless decoder the reference buffer is null if the
frame is an I-frame (flagged with FWHT_FL_I_FRAME).
Make sure not to dereference it in that case.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rename 'v4l2_fwht_default_fmt' to 'v4l2_fwht_find_nth_fmt'
and add a function 'v4l2_fwht_validate_fmt' to check if
a format info matches the parameters.
This function will also be used to validate the stateless
params when adding support for stateless codecs.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Move the code that validates version dependent header
values to a separate function 'validate_by_version'
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the decoder, save the inner reference frame in the same
format as the capture buffer.
The decoder writes directly to the capture buffer and then
the capture buffer is copied to the reference buffer.
This will simplify the stateless decoder.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the field 'buf' to fwht_raw_frame to indicate
the start of the raw frame buffer.
This field will be used to copy the capture buffer
to the reference buffer in the next patch.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Introduce 'prepare_raw_frame' function that fills the values
of a raw frame struct according to the format.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The function 'v4l2_m2m_buf_copy_metadata' should
be called even if decoding/encoding ends with
status VB2_BUF_STATE_ERROR, so that the metadata
is copied from the source buffer to the dest buffer.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2_fwht_encode returns either an error code on
failure or the size of the compressed frame on
success. So change the var assigned to it from
'ret' to 'comp_sz_or_errcode' to clarify that.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
'v4l2_m2m_ctx_release' calls request complete
so it should be called before 'v4l2_ctrl_handler_free'.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The logic of g_selection was wrong: encoders support crop,
decoders support compose, but the code allowed both.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The selection api should check only single buffer types
because multiplanar types are converted to
single in drivers/media/v4l2-core/v4l2-ioctl.c
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Checkpatch wants to use 'help' instead of '---help---':
WARNING: prefer 'help' over '---help---' for new help texts
Let's change it globally at the media subsystem, as otherwise people
would keep using the old way.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
ti-vpe driver parsed the remote endpoints for properties but ignored the
local ones. Fix this by parsing the local endpoint properties instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
V4L2 fwnode matching right now still works based on device nodes, not port
nodes. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When start_streaming was called both last_src_buf and last_dst_buf
pointers were set to NULL, but this depends on whether the capture
or output queue starts streaming.
When decoding with resolution changes in between the capture queue
has to restart streaming whenever a resolution change occurs. And
that would reset last_src_buf as well, which causes a problem if
the decoder was stopped by the application. Since last_src_buf
is now NULL, the LAST flag is never set for the last capture
buffer.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Some functions like enum_fmt use the buffer type as was passed
from userspace, which might cause the switch to fall into the
default case. Just drop the WARN_ON(1) to avoid kernel log pollution.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The s_stream callback was not being called for the first entity in the
stream pipeline array.
Instead of verifying the type of the node (video or subdevice) and
calling s_stream from the second entity in the pipeline, do this process
for all the entities in the pipeline for consistency.
The previous code was not a problem because the first entity is a video
device and not a subdevice, but this patch prepares vimc to allow
setting some configuration in the entity before calling s_stream.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Tested-by: André Almeida <andre.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix line-too-long warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is no need to have the frame field in the vimc_stream struct.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Tested-by: André Almeida <andre.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The type V4L2_FRMSIZE_TYPE_CONTINUOUS expects a step of 1.
This fixes v4l2-compliance test error:
fail: v4l2-test-formats.cpp(184): invalid step_width/height for continuous framesize
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: FAIL
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The state TASK_UNINTERRUPTIBLE should be set just before
schedule_timeout() call, so it knows the sleep mode it should enter.
There is no point in setting TASK_UNINTERRUPTIBLE at the initialization
of the thread as schedule_timeout() will set the state back to
TASK_RUNNING.
This fixes a warning in __might_sleep() call, as it's expecting the
task to be in TASK_RUNNING state just before changing the state to
a sleeping state.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The format of the sink pad should be a bayer mbus format.
This fixes a kernel NULL pointer dereference error that was caused when
the stream starts because the configured format was not found in the
pixelmap table.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Clang-9 makes some different inlining decisions compared to gcc, which
leads to a warning about a possible stack overflow problem when building
with CONFIG_KASAN, including when setting asan-stack=0, which avoids
most other frame overflow warnings:
drivers/media/platform/vicodec/codec-fwht.c:673:12: error: stack frame size of 2224 bytes in function 'encode_plane'
Manually adding noinline_for_stack annotations in those functions
called by encode_plane() or decode_plane() that require a significant
amount of kernel stack makes this impossible to happen with any
compiler.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ISC driver currently supports ITU-R 601 encoding which
utilizes the external hsync and vsync signals. ITU-R 656
format removes the need for these pins by embedding the
sync pulses within the data packet.
To support this feature, enable necessary register bits
when this feature is enabled via device tree.
Signed-off-by: Ken Sloat <ksloat@aampglobal.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Avoid call of dmaengine_terminate_all() between
dmaengine_prep_slave_single() and dmaengine_submit() by locking
the whole DMA submission sequence.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Start streaming was sometimes failing because of pm_runtime_get_sync()
non-0 return value. In fact return value was not an error but a
positive value (1), indicating that PM was already enabled.
Fix this by going to error path only with negative return value.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Function `sh_veu_find_fmt` returns an address that is an addition of a
base pointer `sh_veu_fmt` and an offset. The base pointer refers to a
global variable of which address cannot be NULL. Therefore, this commit
removes the NULL pointer checks on the return values of function
`sh_veu_find_fmt`.
Signed-off-by: Shaobo He <shaobo@cs.utah.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 0650a91499 ("media: mtk-vcodec: Correct return type for mem2mem
buffer helpers") fixed the return types for mem2mem buffer helper
functions, but omitted two occurrences that are accessed in the
mtk_v4l2_debug() macro. These only trigger compiler errors when DEBUG is
defined.
Fixes: 0650a91499 ("media: mtk-vcodec: Correct return type for mem2mem buffer helpers")
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the SoC specific information for RZ/G2M(r8a774a1) SoC.
The VIN module of RZ/G2M is similar to R-Car M3-W.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the MIPI CSI-2 driver support for RZ/G2M(r8a774a1) SoC.
The CSI-2 module of RZ/G2M is similar to R-Car M3-W.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
devm_ioremap_resource() already prints an error message on failure, so
there is no need to repeat that.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Changes to v4l2-fwnode in commit [1] triggered a lockdep warning in
rcar-vin. The first attempt to solve this warning in the rcar-vin driver
was incomplete and only pushed the warning to happen at stream on time
instead of at probe time.
This change reverts the incomplete fix and properly fixes the warning by
removing the need to hold the rcar-vin specific group lock when calling
v4l2_async_notifier_parse_fwnode_endpoints_by_port(). And instead takes
it in the callback where it's really needed.
[1] commit eae2aed1ea ("media: v4l2-fwnode: Switch to
v4l2_async_notifier_add_subdev")
Fixes: 6458afc8c4 ("media: rcar-vin: remove unneeded locking in async callbacks")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the new v4l2_subdev_internal_ops release op to free the
subdev memory only when the last user closed the file handle.
Move v4l2_device_unregister_subdev() to the end of the
vimc_ent_sd_unregister() function since now the unregister_subdev()
call may free the vimc_ent_device struct which is used after the
unregister_subdev() call. So this now has to be done last.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Don't free vimc_cap_device immediately, instead do this
in the video_device release function which is called when the
last user closes the video device. Only then is it safe to
free the memory.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The media_device is part of a static global vimc_device struct.
The media framework expects this to be zeroed before it is
used, however, since this is a global this is not the case if
vimc is unbound and then bound again.
So call memset to ensure any left-over values are cleared.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is not possible to use devm_kzalloc since that memory is
freed immediately when the device instance is unbound.
Various objects like the video device may still be in use
since someone has the device node open, and when that is closed
it expects the memory to be around.
So use kzalloc and release it at the appropriate time.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When vivid is unloaded it used vfree to free dev->bitmap_out,
but it was actually allocated using kmalloc. Use vzalloc
instead, conform what vivid-vid-cap.c does.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Extend the vsp1_du_atomic_flush() API with writeback support by adding
format, pitch and memory addresses of the writeback framebuffer.
Writeback completion is reported through the existing frame completion
callback with a new VSP1_DU_STATUS_WRITEBACK status flag.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The VSP1 driver will need to pass extra flags to the DU through the
frame completion API. Replace the completed bool flag by a bitmask to
support this.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The code that initializes the RPF format-related fields for display
pipelines will also be useful for the WPF to implement writeback
support. Split it from vsp1_du_atomic_update() to a new
vsp1_du_pipeline_set_rwpf_format() function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the writeback feature of the WPF, to enable capturing
frames at the WPF output for display pipelines. To enable writeback the
vsp1_rwpf structure mem field must be set to the address of the
writeback buffer and the writeback field set to true before the WPF
.configure_stream() and .configure_partition() are called. The WPF will
enable writeback in the display list for a single frame, and writeback
will then be automatically disabled.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Refactor the display list header setup to allow chained display lists
with display pipelines. Chain the display lists as for mem-to-mem
pipelines, but enable the frame end interrupt for every list as display
pipelines have a single list per frame.
This feature will be used to disable writeback exactly one frame after
enabling it by chaining a writeback disable display list.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The WPF needs access to the current display list to configure writeback.
Add a display list pointer to the VSP1 entity .configure_stream()
operation.
Only display pipelines can make use of the display list there as
mem-to-mem pipelines don't have access to a display list at stream
configuration time. This is not an issue as writeback is only used for
display pipelines.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To prepare for addition of more flags to the display list, replace the
'internal' flag field by a bitmask 'flags' field.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The VSP-DL instances have two LIFs, and thus two copies of the
VI6_DISP_IRQ_ENB, VI6_DISP_IRQ_STA and VI6_WPF_WRBCK_CTRL registers. Fix
the corresponding macros accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Display list fragments have been renamed to bodies. Replace one last
occurrence of the word fragment in the documentation.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When configuring partitions for memory-to-memory pipelines, the WPF
accesses data of the current partition through pipe->partition.
Writeback support will require full configuration of the WPF while not
providing a valid pipe->partition. Rework the configuration code to fall
back to the full image width in that case, as is already done for the
part of the configuration currently relevant for display pipelines.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This reverts commit 3299ba5c0b ("[media] v4l: vsp1: Supply frames to
the DU continuously")
The DU output mode does not rely on frames being supplied on the WPF as
its pipeline is supplied from DRM. For the upcoming WPF writeback
functionality, we will choose to enable writeback mode if there is an
output buffer, or disable it (leaving the existing display pipeline
unharmed) otherwise.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
- Fix a unittest failure on UML. Preparation for converting to
kunit test framework.
- Add annotations to dtx_diff output
- Fix unittest reporting of expected error
- Move DMA configuration for virtual devices into the driver that
needs it (s5p-mfc)
- Vendor prefixes for feiyang and techstar
- Convert ARM GIC, GICv3, and L2x0 to DT schema
- Add r8a7778/9 HSCIF serial bindings
-----BEGIN PGP SIGNATURE-----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=CnTd
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- Fix a unittest failure on UML. Preparation for converting to kunit
test framework.
- Add annotations to dtx_diff output
- Fix unittest reporting of expected error
- Move DMA configuration for virtual devices into the driver that needs
it (s5p-mfc)
- Vendor prefixes for feiyang and techstar
- Convert ARM GIC, GICv3, and L2x0 to DT schema
- Add r8a7778/9 HSCIF serial bindings
* tag 'devicetree-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: unittest: unflatten device tree on UML when testing
dt-bindings: Add vendor prefix for feiyang
dt-bindings: Add vendor prefix for techstar
dt-bindings: display: add missing semicolon in example
of: mark early_init_dt_alloc_reserved_memory_arch static
of: add dtc annotations functionality to dtx_diff
of: unittest: add caution to function header comment
of: unittest: remove report of expected error
dt-bindings: interrupt-controller: Convert ARM GICv3 to json-schema
dt-bindings: interrupt-controller: Convert ARM GIC to json-schema
dt-bindings: arm: l2x0: Convert L2 cache to json-schema
media: s5p-mfc: Fix memdev DMA configuration
dt-bindings: serial: sh-sci: Document r8a7778/9 HSCIF bindings
As we did lots of change at vim2m driver, let's take the
opportunity and make checkpatch happier, addressing the
errors/warnings that makes sense.
While here, increment driver's version.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There's no reason why this driver should use BUG(). Instead,
just properly handle issue, returning an error code where
pertinent.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When in passthrough mode, copy the entire line at once, in
order to make it faster (if not HFLIP).
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add an horizontal linear scaler using Breseham algorithm in
order to speep up its calculus.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Handling any Y,Cr,Cb formats require some extra logic, as it
handles a group of two pixels. That's easy while we don't do
horizontal scaling.
However, doing horizontal scaling with such formats would require
a lot more code, in order to avoid distortions, as, if it scales
to two non-consecutive points, the logic would need to read 4
points in order to properly convert to RGB.
As this is just a test driver, and we want fast algorithms,
let's just get rid of this format as an output one.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When resolutions are different, the expected behavior is to
scale the image. Implement a vertical scaler as the first step.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The vim2m driver doesn't enforce that the capture and output
buffers would have the same size. Do the right thing if the
buffers are different, zeroing the buffer before writing,
ensuring that lines will be aligned and it won't write past
the buffer area.
This is a temporary fix.
A proper fix is to either implement a simple scaler at vim2m,
or to better define the behaviour of M2M transform drivers
at V4L2 API with regards to its capability of scaling the
image or not.
In any case, such changes would deserve a separate patch
anyway, as it would imply on some behavoral change.
Also, as we have an actual bug of writing data at wrong
places, let's fix this here, and add a mental note that
we need to properly address it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The only real restriction at vim2m is that width should be
multiple of two, as the copy routine always copy two pixels
each time.
However, Bayer formats are defined as having a 2x2 matrix.
So, odd vertical numbers would cause color distortions at the
last line. So, it makes sense to use step 2 for vertical alignment
on Bayer.
With this patch, the reported formats for video capture will
be:
[0]: 'RGBP' (16-bit RGB 5-6-5)
Size: Stepwise 32x32 - 640x480 with step 2/1
[1]: 'RGBR' (16-bit RGB 5-6-5 BE)
Size: Stepwise 32x32 - 640x480 with step 2/1
[2]: 'RGB3' (24-bit RGB 8-8-8)
Size: Stepwise 32x32 - 640x480 with step 2/1
[3]: 'BGR3' (24-bit BGR 8-8-8)
Size: Stepwise 32x32 - 640x480 with step 2/1
[4]: 'YUYV' (YUYV 4:2:2)
Size: Stepwise 32x32 - 640x480 with step 2/1
[5]: 'BA81' (8-bit Bayer BGBG/GRGR)
Size: Stepwise 32x32 - 640x480 with step 2/2
[6]: 'GBRG' (8-bit Bayer GBGB/RGRG)
Size: Stepwise 32x32 - 640x480 with step 2/2
[7]: 'GRBG' (8-bit Bayer GRGR/BGBG)
Size: Stepwise 32x32 - 640x480 with step 2/2
[8]: 'RGGB' (8-bit Bayer RGRG/GBGB)
Size: Stepwise 32x32 - 640x480 with step 2/2
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The copy logic assumes that the data width is multiple of two,
as this is needed in order to support YUYV.
There's no reason to force it to be 8-pixel aligned, as 2-pixel
alignment is enough.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The vim2m device is interesting to simulate a webcam. As most
sensors are arranged using bayer formats, the best is to support
to output data using those formats.
So, add support for them.
All 4 8-bit bayer formats tested with:
$ qvidcap -p &
$ v4l2-ctl --stream-mmap --stream-out-mmap --stream-to-host localhost --stream-lossless --stream-out-hor-speed 1 -v pixelformat=RGGB
It was tested also with GStreamer with:
$ gst-validate-1.0 filesrc location=some_video.mp4 ! qtdemux ! avdec_h264 ! videoconvert ! videoscale ! v4l2convert disable-passthrough=1 extra-controls="s,horizontal_flip=0,vertical_flip=0" ! bayer2rgb ! videoconvert ! xvimagesink
For all possible HFLIP/VFLIP values.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Those typos were left over from codespell check, on
my first pass or belong to code added after the time I
ran it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add non vendor bayer formats to the allowed format array.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a flag 'FWHT_FL_I_FRAME' that indicates that
this is an I-frame. This requires incrementing
to version 3
This flag is needed for the upcoming stateless FWHT
decoder since it has to know if an encoded frame is
an I or a P frame.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
[hverkuil-cisco@xs4all.nl: added the last paragraph of the commit msg]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The check to see if type is V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE is redundant
as this has been already checked at the start of the function and if
it's not that value then -ENOSYS is returned. Hence the sprintf can be
replaced by a simpler string copy.
Detected by CoverityScan, CID#1309450 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix the assigned type of mem2mem buffer handling API.
Namely, these functions:
v4l2_m2m_next_buf
v4l2_m2m_last_buf
v4l2_m2m_buf_remove
v4l2_m2m_next_src_buf
v4l2_m2m_next_dst_buf
v4l2_m2m_last_src_buf
v4l2_m2m_last_dst_buf
v4l2_m2m_src_buf_remove
v4l2_m2m_dst_buf_remove
return a struct vb2_v4l2_buffer, and not a struct vb2_buffer.
Fixing this is necessary to fix the mem2mem buffer handling API,
changing the return to the correct struct vb2_v4l2_buffer instead
of a void pointer.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CSI controller can take raw data from the data bus and output it
directly to capture buffers. This can be used to support the JPEG media
bus format.
While the controller can report minimum and maximum bytes per line, it
has no way to report how many lines were captured in the last frame.
Thus, even when the on-bus data is framed correctly, we have no way to
accertain the actual amount of data captured, unless we scan the buffer
for JPEG EOI markers, or sequential zeros. For now we leave bytesused
alone, and leave it up to userspace applications to parse the data.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CSI controller can take raw data from the data bus and output RGB565
format. The controller does not distinguish between RGB565 LE and BE.
Instead this is determined by the media bus format, i.e. the format or
order the sensor is sending data in.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
max_register is currently set to 0x1000. This is beyond the mapped
address range of the hardware, so attempts to dump the regmap from
debugfs would trigger a kernel exception.
Furthermore, the useful registers only occupy a small section at the
beginning of the full range. Change the value to 0x9c, the last known
register on the V3s and H3.
On the A31, the register range is extended to support additional
capture channels. Since this is not yet supported, ignore it for now.
Fixes: 5cc7522d89 ("media: sun6i: Add support for Allwinner CSI V3s")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
drivers/media/platform/vsp1/vsp1_drm.c: drivers/media/platform/vsp1/vsp1_drm.c:336 vsp1_du_pipeline_setup_brx() error: we previously assumed 'pipe->brx' could be null (see line 244)
smatch missed that if pipe->brx was NULL, then later on it will be
set with a non-NULL value. But it is easier to just use the brx pointer
so smatch doesn't get confused.
Tested-on: Salvator-XS-ES2.0, Salvator-XS-M3N
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
CSI block in Allwinner A64 has similar features as like in H3,
but the default CSI_SCLK rate cannot work properly to drive the
connected sensor interface.
The tested mod cock rate is 300 MHz and BSP vfe media driver is also
using the same rate. Unfortunately there is no valid information about
clock rate in manual or any other sources except the BSP driver. so more
faith on BSP code, because same has tested in mainline.
So, add support for A64 CSI block by setting updated mod clock rate.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Buffers generated with YUV32 format seems to be incorrect, hence use
VUYA32 instead.
Changes from v1:
Add both formats VUYA32 and VUYX32 but associate only VUYX32 to the
output queue as the alpha channel of buffers is ignored on this queue.
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Enable vivid to make use of the following formats:
V4L2_PIX_FMT_AYUV32
V4L2_PIX_FMT_XYUV32
V4L2_PIX_FMT_VUYA32
V4L2_PIX_FMT_VUYX32
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
media_device_cleanup() wasn't called, which caused a small
memory leak.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When the media device registration fails, don't call media_device_unregister
since the device was never actually registered.
When removing the module also call media_device_cleanup() to avoid a memory leak.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The SoC camera framework has no functional drivers left, something that
has not changed for years. Move the leftovers to the staging tree.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove unused but set variables to clean up the code and avoid
warning.
Signed-off-by: Lucas A. M. Magalhães <lucmaga@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add VB2_USERPTR to the vimc capture device.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A merge conflict rised when merging from -rc7. Fix it.
In this specific case, we don't need the if anymore, as the
work_run was moved to its rightful place (struct vim2m_ctx).
Fixes: b3e64e5b07 ("media: vim2m: use per-file handler work queue")
Fixes: 240809ef66 ("media: vim2m: only cancel work if it is for right context")
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlxqHJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGWl8H/jPI4EipzD2GbnjZ
GaFpMBBjcXBaVmoA+Y69so+7BHx1Ql+5GQtqbK0RHJRb9qEPLw3FBhHNjM/N8Sgf
nSrK+GnBZp9s+k/NR/Yf2RacUR3jhz+Q9JEoQd3u9bFUeQyvE8Rf3vgtoBBwFOfz
+t7N1memYVF3asLGWB4e4sP1YVMGfseTQpSPojvM30YWM86Bv+QtSx1AGgHczQIM
kMKealR8ZPelN6JAXgLhQ5opDojBrE4YKB98pwsMDI6abz0Tz2JLFEUTTxsv5XNN
o/Iz+XDoylskEyxN2unNWfHx7Swkvoklog8J/hDg5XlTvipL/WkT66PHBgcGMNvj
BW9GgU8=
=ZizU
-----END PGP SIGNATURE-----
Merge tag 'v5.0-rc7' into patchwork
Linux 5.0-rc7
* tag 'v5.0-rc7': (1667 commits)
Linux 5.0-rc7
Input: elan_i2c - add ACPI ID for touchpad in Lenovo V330-15ISK
Input: st-keyscan - fix potential zalloc NULL dereference
Input: apanel - switch to using brightness_set_blocking()
powerpc/64s: Fix possible corruption on big endian due to pgd/pud_present()
efi/arm: Revert "Defer persistent reservations until after paging_init()"
arm64, mm, efi: Account for GICv3 LPI tables in static memblock reserve table
sunrpc: fix 4 more call sites that were using stack memory with a scatterlist
include/linux/module.h: copy __init/__exit attrs to init/cleanup_module
Compiler Attributes: add support for __copy (gcc >= 9)
lib/crc32.c: mark crc32_le_base/__crc32c_le_base aliases as __pure
auxdisplay: ht16k33: fix potential user-after-free on module unload
x86/platform/UV: Use efi_runtime_lock to serialise BIOS calls
i2c: bcm2835: Clear current buffer pointers and counts after a transfer
i2c: cadence: Fix the hold bit setting
drm: Use array_size() when creating lease
dm thin: fix bug where bio that overwrites thin block ignores FUA
Revert "exec: load_script: don't blindly truncate shebang string"
Revert "gfs2: read journal in large chunks to locate the head"
net: ethernet: freescale: set FEC ethtool regs version
...
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is good practice to fill in bus_info.
Also just use 'platform:vimc' when filling in the bus_info in querycap:
the bus_info has nothing to do with the video device name.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
drivers/media/platform/pxa_camera.c:2400 pxa_camera_probe() error: we previously assumed 'pcdev->pdata' could be null (see line 2397)
First check if platform data is provided, then check if DT data is provided,
and if neither is provided just return with -ENODEV.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The v4l2_m2m_buf_copy_data helper is used to copy the buffer
metadata, such as its timestamp and its flags.
Therefore, the v4l2_m2m_buf_copy_metadata name is more clear
and avoids confusion with a payload data copy.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: also fix cedrus_dec.c]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It seems that it is possible that dev to be null, as there's
a warning printing:
"Instance released before the end of transaction"
Solves this warning:
drivers/media/platform/vim2m.c: drivers/media/platform/vim2m.c:525 device_work() warn: variable dereferenced before check 'curr_ctx' (see line 523)
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To correctly set the size of the image in a plane, it's needed
to divide the height of image by the vertical down sampling factor.
This was only happening in vivid_try_fmt_vid_cap(), but now it
applied in others sizeimage calculations as well.
Signed-off-by: André Almeida <andre.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a linear pipeline logic for the stream control. It's created by
walking backwards on the entity graph. When the stream starts it will
simply loop through the pipeline calling the respective process_frame
function of each entity.
Fixes: f2fe89061d ("vimc: Virtual Media Controller core, capture
and sensor")
Cc: stable@vger.kernel.org # for v4.20
Signed-off-by: Lucas A. M. Magalhães <lucmaga@gmail.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fixed small space-after-tab issue in the patch]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Just like vb2 does, use u64 internally to store the timestamps
of the buffers. Only convert to timeval when interfacing with
userspace.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The SOURCE_CHANGE event is decoder specific, so don't allow it for
encoders.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is good practice to fill in the bus_info.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is good practice to fill in bus_info.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Check that the selection buf_type is valid before calling get_q_data() to
avoid hitting the WARN(1) in that function if the buffer type is not valid.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+44b24cff6bf96006ecfa@syzkaller.appspotmail.com
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
While there's a control to allow setting it at runtime, as the
control handler is per file handler, only the application setting
the m2m device can change it. As this is a custom control, it is
unlikely that existing apps would be able to set it.
Due to that, and due to the fact that v4l2-mem2mem serializes all
accesses to a m2m device, trying to setup two GStreamer
v4l2videoconvert instance at the same time will cause frame drops.
So, add an alternate way of setting its default via a modprobe parameter.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It doesn't make sense to have a per-device work queue, as the
scheduler should be called per file handler. Having a single
one causes failures if multiple streams are filtered by vim2m.
So, move it to be inside the context structure.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Despite vim2m is reporting that it supports RGB565BE and YUYV,
that's not true.
Right now, it just says that it supports both format, but it
doesn't actually support them.
Also, horizontal flip is not properly implemented. It sounds
that it was designed to do a pseudo-horizontal flip using 8
tiles. Yet, as it doesn't do format conversion, the result
is a mess.
I suspect that it was done this way in order to save CPU time,
at the time of OMAP2 days.
That's messy and doesn't really help if someone wants to
use vim2m to test a pipeline.
Worse than that, the unique RGB format it says it supports is
RGB565BE, with is not supported by Gstreamer. That prevents
practical usage of it, even for tests.
So, instead, properly implement fourcc format conversions,
adding a few more RGB formats:
- RGB and BGR with 24 bits
- RGB565LE (known as RGB16 at gstreamer)
Also allows using any of the 5 supported formats as either
capture or output.
Note: The YUYV conversion routines are based on the conversion code
written by Hans de Goede inside libv4lconvert (part of v4l-utils),
released under LGPGL 2.1 (GPL 2.0 compatible).
Tested all possible format combinations except for RGB565BE,
as Gstreamer currently doesn't support it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The wrong size check was performed for output formats like NV24 which
set vfmt->buffers to 1, but vfmt->planes is 2. It was incorrectly
checking the payload size for plane 1, which doesn't exist.
Note: vfmt->buffers refers to the number of per-plane-buffers that
should be allocated. vfmt->planes refers to the number of planes
that make up an image. vfmt->planes may be > vfmt->buffers.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Validate the field for an output buffer. This ensures that the
field is validated when the buffer is queued to a request, and
not when the request itself is queued, which is too late.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Validate the field for an output buffer. This ensures that the
field is validated when the buffer is queued to a request, and
not when the request itself is queued, which is too late.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Vdec: Using standard CCF interface to set parent clock and
clock rate in dtsi and using common interface to open/close
video decoder clock.
Venc: Using standard CCF interface to set parent clock in dtsi
and using common interface to open/close video encoder clock.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Qianqian Yan <qianqian.yan@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
drivers/media/platform/vicodec/vicodec-core.c:drivers/media/platform/vicodec/vicodec-core.c:210:23: warning: symbol 'get_next_header' was not declared. Should it be static?
drivers/media/platform/vicodec/vicodec-core.c:210:23: warning: no previous prototype for 'get_next_header' [-Wmissing-prototypes]
enum vb2_buffer_state get_next_header(struct vicodec_ctx *ctx, u8 **pp, u32 sz)
^~~~~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make sure that the pointer to the compressed frame does not
get out of the buffer.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the the queues are not streaming then the first resolution
change is handled in the buf_queue callback.
The following resolution change events are handled in job_ready.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: wrap info_from_header prototype]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Keep the fwht header in separated field from the data.
Refactor job_ready to use a new function 'get_next_header'
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add flags indicating the pixel encoding - yuv/rgb/hsv to
fwht header and to the pixel info. Use it to enumerate
the supported pixel formats.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use 3 bits for the number of components mask in the fwht
header flags
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the selection api for the crop and compose targets.
The driver rounds up the coded width and height such that
all planes dimensions are multiple of 8.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the field 'num_planes' to 'v4l2_fwht_pixfmt_info' struct.
Signed-off-by: Dafna Hirschfeld <dafna3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The zero timestamp is really valid so fix that mistake by
dropping the code which checks for zero timestamp.
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This corrects clock frequency table rates to be in sync
with video clock controller frequency table.
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>