Commit Graph

56 Commits

Author SHA1 Message Date
Hugues Fruchet b97eef5d77 mfd: stmpe: Fix bit clearing on STMPE1600
GPIO bits clearing on pins assigned to STMPE1600
had no effects due to missing "clear registers"
settings within stmpe1600_regs[].
STMPE1600 does not have dedicated "clear registers",
but single "set/clear registers", hence stmpe1600_regs[]
"clear registers" (STMPE_IDX_GPCR_XXX) must be set to
same value as "set registers" (STMPE_IDX_GPSR_XXX), ie
STMPE1600_REG_GPSR_XXX.

Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-04-27 09:25:07 +01:00
Linus Walleij f40584200b mfd: stmpe: Fix RESET regression on STMPE2401
Since commit c4dd1ba355
("mfd: stmpe: Add reset support for all STMPE variant")
we're resetting the STMPE expanders before use.

This caused a regression on the STMP2401 on the Nomadik
NHK8815:

stmpe-i2c 0-0043: stmpe2401 detected, chip id: 0x101
nmk-i2c 101f8000.i2c0: write to slave 0x43 timed out
nmk-i2c 101f8000.i2c0: no ack received after address transmission
stmpe-i2c 0-0044: stmpe2401 detected, chip id: 0x101
nmk-i2c 101f8000.i2c0: write to slave 0x44 timed out
nmk-i2c 101f8000.i2c0: no ack received after address transmission

It turns out that we start to poll for the reset bit to
go low again too quickly: the STMPE2401 is not yet online and
ready to be asked for the status of the RESET bit.

By introducing a 10ms delay before starting to hammer
the register for information, we get back to normal:

stmpe-i2c 0-0043: stmpe2401 detected, chip id: 0x101
stmpe-i2c 0-0044: stmpe2401 detected, chip id: 0x101

Cc: stable@vger.kernel.org
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Fixes: c4dd1ba355 ("mfd: stmpe: Add reset support for all STMPE variant")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-11-16 09:50:33 +00:00
Patrice Chotard 6bb9f0d933 mfd: Add STMPE1600 support
STMPE1600 is a 16-bit port expander.
Datasheet is available here :
http://www2.st.com/content/st_com/en/products/interfaces-and-transceivers/
i-o-expanders-and-level-translators/i-o-expanders/stmpe1600.html

Signed-off-by: Amelie DELAUNAY <amelie.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-08-10 09:25:18 +01:00
Patrice Chotard 897ac6674c mfd: stmpe: Rework registers access
this update allows to use registers map as following :
regs[reg_index + offset] instead of
regs[reg_index] + offset

This makes code clearer and will facilitate the addition of STMPE1600
on which LSB and MSB registers are respectively located at addr and addr + 1.
Despite for all others STMPE variant, LSB and MSB registers are respectively
located in reverse order at addr + 1 and addr.

For variant which have 3 registers's bank, we use LSB,CSB and MSB indexes
which contains respectively LSB (or LOW), CSB (or MID) and MSB (or HIGH)
register addresses (STMPE1801/STMPE24xx).
For variant which have 2 registers's bank, we use LSB and CSB indexes only.
In this case the CSB index contains the MSB regs address (STMPE 1601).

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-08-10 09:24:39 +01:00
Patrice Chotard c16bee7897 mfd: stmpe: Use generic bit mask name
In order to prepare the ground to STMPE1600,
as STMPE1600's SYS_CTRL register has the same layout as
STMPE801 variant, unify STMPExxx_REG_SYS_CTRL_RESET/INT_EN/INT_HI
bit masks to more generic STMPE_SYS_CTRL_RESET/INT_EN/INT_HI

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-08-10 09:24:29 +01:00
Patrice Chotard c4dd1ba355 mfd: stmpe: Add reset support for all STMPE variant
Reset was only implemented for STMPE1801 variant despite
all variant have a SOFT_RESET bit.

For STMPE2401/2403/801/1601/1801 SOFT_RESET bit is bit 7
of SYS_CTRL register.
For STMPE610/811 (which have the same variant id) SOFT_RESET
bit is bit 1 of SYS_CTRL register.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-08-10 09:23:33 +01:00
Patrice Chotard 0f4be8cf63 mfd: stmpe: Add STMPE_IDX_SYS_CTRL/2 enum
As STMPE1801/1601/24xx has a SYS_CTRL register and
STMPE1601/2403 has even a SYS_CTRL2 register, add
STMPE_IDX_SYS_CTRL/2 and update driver code accordingly

This update prepares the ground for not yet supported STMPE1600
which share similar REG_SYS_CTRL register.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-08-10 09:23:25 +01:00
Linus Walleij fc1882dcb5 mfd: stmpe: Move platform data into MFD driver
The STMPE platform data is only populated from the device tree
in all existing users, so push the struct and make the OF case
the norm.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-06-29 10:15:51 +01:00
Linus Walleij b273c5e0b6 mfd: stmpe: Add the proper PWM resources
This adds the PWM resources to the STMPE MFD driver, so that
it can properly grab and use them.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-03-16 08:50:37 +00:00
Linus Walleij f6d1034139 mfd: stmpe: PWM on 24xx has altfunc 1
On the STMPE2401 and STMPE2401 altfunction 1 corresponds to the
PWM channels. This oneliner was missing in the case-switch, making
it impossible to enable the PWM channel output.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-10-26 14:48:57 +00:00
Rob Herring 9bd09f345e mfd: Kill off set_irq_flags usage
set_irq_flags is ARM specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:

IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN

For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in
.map() functions and we can simply remove the set_irq_flags calls. Some
users also modify IRQ_NOPROBE and this has been maintained although it
is not clear that is really needed. There appears to be a great deal of
blind copy and paste of this code.

Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-08-11 15:09:01 +01:00
Krzysztof Kozlowski 7ce7b26f84 mfd: Constify regmap and irq configuration data
Constify in various drivers configuration data which is not modified:
 - regmap_irq_chip,
 - individual regmap_irq's in array,
 - regmap_config,
 - irq_domain_ops,

Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-22 12:25:01 +01:00
Linus Torvalds bac22980b0 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input layer fixes from Dmitry Torokhov:
 "Fixes for v7 protocol for ALPS devices and few other driver fixes.

  Also users can request input events to be stamped with boot time
  timestamps, in addition to real and monotonic timestamps"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: hil_kbd - fix incorrect use of init_completion
  Input: alps - v7: document the v7 touchpad packet protocol
  Input: alps - v7: fix finger counting for > 2 fingers on clickpads
  Input: alps - v7: sometimes a single touch is reported in mt[1]
  Input: alps - v7: ignore new packets
  Input: evdev - add CLOCK_BOOTTIME support
  Input: psmouse - expose drift duration for IBM trackpoints
  Input: stmpe - bias keypad columns properly
  Input: stmpe - enforce device tree only mode
  mfd: stmpe: add pull up/down register offsets for STMPE
  Input: optimize events_per_packet count calculation
  Input: edt-ft5x06 - fixed a macro coding style issue
  Input: gpio_keys - replace timer and workqueue with delayed workqueue
  Input: gpio_keys - allow separating gpio and irq in device tree
2014-12-30 16:59:59 -08:00
Linus Walleij 80e1dd82be mfd: stmpe: add pull up/down register offsets for STMPE
This adds the register offsets for pull up/down for the STMPE
1601, 1801 and 24xx expanders. This is used to bias GPIO lines
and keypad lines.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2014-12-15 21:46:11 -08:00
Sean Cross 851ec59614 mfd: stmpe: Support gpio over irq under device tree
The stmpe_platform_data has a irq_over_gpio field, which allows the
system to read STMPE events whenever an IRQ occurs on a GPIO pin.
This patch adds the ability to configure this field and to use a GPIO
as an IRQ source for boards configuring the STMPE in device tree.

Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:23:53 +01:00
Lee Jones 7929fa7740 mfd: stmpe: Rid variable length array Sparse warnings
Numbers are generated by taking the largest currently used values.

drivers/mfd/stmpe.c:252:17:
  warning: Variable length array is used.
drivers/mfd/stmpe.c:857:16:
  warning: Variable length array is used.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26 08:15:47 +01:00
Lee Jones c00572bc94 mfd: stmpe: Rid data size incompatibility warn when building for 64bit
Extinguishes:

../drivers/mfd/stmpe-i2c.c: In function ‘stmpe_i2c_probe’:
../drivers/mfd/stmpe-i2c.c:88:13:
	warning: cast from pointer to integer of different size
	partnum = (int)of_id->data;

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-09 16:37:55 +01:00
Linus Walleij 9e9dc7d959 mfd: stmpe: root out static GPIO and IRQ assignments
The only platform using the STMPE expander now boots from
device tree using all-dynamic GPIO and IRQ number assignments, so
remove the mechanism to pass this from the device tree entirely.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-05-23 09:41:01 +01:00
Linus Walleij 9c9e321455 mfd: stmpe: add optional regulators
The STMPE has VCC and VIO supply lines, and sometimes (as on
Ux500) this comes from a software-controlled regulator. Make
it possible to supply the STMPE with power from these
regulators.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-05-09 10:51:12 +01:00
Linus Walleij b69d2ad674 mfd: stmpe: mask off unused blocks properly
The STMPE driver would just read/modify/write the system control
register on the STMPE1601, meaning it would not properly mask off
the PWM block, which remained active if it was on at boot time.
This makes sure the blocks are always masked off if they were
active on boot, saving some power. Also rename the inconsistenty
named STMPE1601 define for the PWM block activation.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-05-09 10:51:06 +01:00
Sachin Kamat 52397fe18d mfd: stmpe: Trivial: Remove unnecessary semicolon
Semicolon is not necessary after the while statement.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-03-19 08:58:07 +00:00
Geert Uytterhoeven 6bbb3c4cb2 mfd: stmicro: Constify struct mfd_cell where possible
As of commit 03e361b25e ("mfd: Stop setting
refcounting pointers in original mfd_cell arrays"), the "cell" parameter of
mfd_add_devices() is "const" again. Hence make all cell data passed to
mfd_add_devices() const where possible.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-01-06 09:13:24 +00:00
Mark Brown a9c4055da8 mfd: stmpe: Staticise stmpe_of_probe()
It is only called from this file so there is no need for it to be in the
global namespace and cause sparse to warn.

Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-07-31 13:01:45 +01:00
Javier Martinez Canillas 1a5595cb28 mfd: stmpe: use irq_get_trigger_type() to get IRQ flags
Use irq_get_trigger_type() to get the IRQ trigger type flags
instead calling irqd_get_trigger_type(irq_get_irq_data(irq))

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/1371228049-27080-5-git-send-email-javier.martinez@collabora.co.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2013-06-25 11:48:25 +02:00
Jean-Nicolas Graux 230f13a503 mfd: support stmpe1801 18 bits enhanced port expander
Provides support for 1801 variant of stmpe gpio port expanders.
This chip has 18 gpios configurable as GPI, GPO, keypad matrix,
special key or dedicated key function.

Note that special/dedicated key function is not supported yet.

Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-04-09 14:15:58 +02:00
Gabriel Fernandez 408a3fa867 mfd: stmpe: DT: Add stmpe-i2c dt alias to get id device
This patch augments the STMP driver to read the device id
from the stmpe-i2c dt alias if present.

Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-04-05 18:05:54 +02:00
Gabriel Fernandez a200e320f7 mfd: stmpe: DT: Enable no-irq mode configuration
If there is no interrupt property into stmpe node
then activate the no-irq mode by setting the irq
value to -1.

Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-04-05 18:05:54 +02:00
Greg Kroah-Hartman 612b95cd79 Drivers: mfd: remove __dev* attributes.
CONFIG_HOTPLUG is going away as an option.  As a result, the __dev*
markings need to be removed.

This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.

Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.

Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-03 15:57:14 -08:00
Linus Torvalds 31564cbd77 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull second round of input updates from Dmitry Torokhov:
 "As usual, there are a couple of new drivers, input core now supports
  managed input devices (devres), a slew of drivers now have device tree
  support and a bunch of fixes and cleanups."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (71 commits)
  Input: walkera0701 - fix crash on startup
  Input: matrix-keymap - provide a proper module license
  Input: gpio_keys_polled - switch to using gpio_request_one()
  Input: gpio_keys - switch to using gpio_request_one()
  Input: wacom - fix touch support for Bamboo Fun CTH-461
  Input: xpad - add a few new VID/PID combinations
  Input: xpad - minor formatting fixes
  Input: gpio-keys-polled - honor 'autorepeat' setting in platform data
  Input: tca8418-keypad - switch to using managed resources
  Input: tca8418_keypad - increase severity of failures in probe()
  Input: tca8418_keypad - move device ID tables closer to where they are used
  Input: tca8418_keypad - use dev_get_platdata() to retrieve platform data
  Input: tca8418_keypad - use a temporary variable for parent device
  Input: tca8418_keypad - add support for shared interrupt
  Input: tca8418_keypad - add support for device tree bindings
  Input: remove Compaq iPAQ H3600 (Bitsy) touchscreen driver
  Input: bu21013_ts - add support for Device Tree booting
  Input: bu21013_ts - move GPIO init and exit functions into the driver
  Input: bu21013_ts - request regulator that actually exists
  ARM: ux500: Strip out duplicate touch screen platform information
  ...
2012-12-18 12:46:37 -08:00
Linus Torvalds 2dfea3803d This is the MFD patch set for the 3.8 merge window.
We have several new drivers, most of the time coming with their sub devices
 drivers:
 
 - Austria Microsystem's AS3711
 - Nano River's viperboard
 - TI's TPS80031, AM335x TS/ADC,
 - Realtek's MMC/memstick card reader
 - Nokia's retu
 
 We also got some notable cleanups and improvements:
 
 - tps6586x got converted to IRQ domains.
 - tps65910 and tps65090 moved to the regmap IRQ API.
 - STMPE is now Device Tree aware.
 - A general twl6040 and twl-core cleanup, with moves to the regmap I/O and IRQ
   APIs and a conversion to the recently added PWM framework.
 - sta2x11 gained regmap support.
 
 Then the rest is mostly tiny cleanups and fixes, among which we have Mark's
 wm5xxx and wm8xxx patchset.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJQznPnAAoJEIqAPN1PVmxKuA8P/0nOJduXFM1c0Gy+DD5DnJnG
 cXzzeSTV8iO3a3sHIye43QPJ5V2YUR5uxLTUEOo/G7my/MoZ/azeNidkUD3qLVlm
 wVIq35lcS8dWTZaY7nlpBcWc6e39UB0sEueuJNxyhOv5lnMKdi2tAow5f4vIRQnd
 Q67/EbrgqdltcOpGmVuCdQcvphvWgy+K65jzbJG5zXs7hGX13Q+M5RnYhx76kc8f
 TDd0APZ71n5/RyISFSBSu2vfl2kES6o47aMgqqXMEHri6d3puAaXM0rFoMzXg/4G
 eBdxndN25H7rW7xvt9tuUod2rn1AO7tif5d7jal3Cfj61y3iqKY30yb3OzS9XQXH
 9WZ2qDst11zvzQivxIkMGvfRXRfncNLWR4DrBSqVfSbYV2uQj2eS8C6ONwKVMXsQ
 5tjNp91PFqN19sWQjIjSMcrNswxgpvdQ9mqFTyOGmISbqrpPSTi+MuO8r9+xTfUF
 PnzUX2nVOW/i9NcI7uotjzh8jiw6t8XMVHhkehiSYR9hzCb6MaPsFPN4jWq9XA2m
 1htCHylNpHqHQ3Mup7Is6j0Li1ahdwfm4lbrgiVEA4t4Mqs5E/Ka+3V8laNAKylW
 PfCP/VmnJYzmgVTK/qobFNeKzRqR0i4WTL6T7oAxGL87Q4TJaqKpEkXWne8UXV+Q
 yIbN0fmWfCveCetM+vaf
 =F790
 -----END PGP SIGNATURE-----

Merge tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6

Pull MFS update from Samuel Ortiz:
 "This is the MFD patch set for the 3.8 merge window.

  We have several new drivers, most of the time coming with their sub
  devices drivers:

   - Austria Microsystem's AS3711
   - Nano River's viperboard
   - TI's TPS80031, AM335x TS/ADC,
   - Realtek's MMC/memstick card reader
   - Nokia's retu

  We also got some notable cleanups and improvements:

   - tps6586x got converted to IRQ domains.
   - tps65910 and tps65090 moved to the regmap IRQ API.
   - STMPE is now Device Tree aware.
   - A general twl6040 and twl-core cleanup, with moves to the regmap
     I/O and IRQ APIs and a conversion to the recently added PWM
     framework.
   - sta2x11 gained regmap support.

  Then the rest is mostly tiny cleanups and fixes, among which we have
  Mark's wm5xxx and wm8xxx patchset."

Far amount of annoying but largely trivial conflicts.  Many due to
__devinit/exit removal, others due to one or two of the new drivers also
having come in through another tree.

* tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (119 commits)
  mfd: tps6507x: Convert to devm_kzalloc
  mfd: stmpe: Update DT support for stmpe driver
  mfd: wm5102: Add readback of DSP status 3 register
  mfd: arizona: Log if we fail to create the primary IRQ domain
  mfd: tps80031: MFD_TPS80031 needs to select REGMAP_IRQ
  mfd: tps80031: Add terminating entry for tps80031_id_table
  mfd: sta2x11: Fix potential NULL pointer dereference in __sta2x11_mfd_mask()
  mfd: wm5102: Add tuning for revision B
  mfd: arizona: Defer patch initialistation until after first device boot
  mfd: tps65910: Fix wrong ack_base register
  mfd: tps65910: Remove unused data
  mfd: stmpe: Get rid of irq_invert_polarity
  mfd: ab8500-core: Fix invalid free of devm_ allocated data
  mfd: wm5102: Mark DSP memory regions as volatile
  mfd: wm5102: Correct default for LDO1_CONTROL_2
  mfd: arizona: Register haptics devices
  mfd: wm8994: Make current device behaviour the default
  mfd: tps65090: MFD_TPS65090 needs to select REGMAP_IRQ
  mfd: Fix stmpe.c build when OF is not enabled
  mfd: jz4740-adc: Use devm_kzalloc
  ...
2012-12-16 18:55:20 -08:00
Vipul Kumar Samar ac713cc9fc mfd: stmpe: Update DT support for stmpe driver
This patch extends existing DT support for stmpe devices. This updates:
- missing header files in stmpe.c
- stmpe_of_probe() with pwm, rotator and new bindings.
- Bindings are updated in binding document.

Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-12-10 10:03:50 +01:00
Vipul Kumar Samar 86605cfe8c gpio: stmpe: Add DT support for stmpe gpio
This patch allows the STMPE GPIO driver to be successfully probed and
initialised when Device Tree support is enabled. Bindings are mentioned in
Documentation too.

Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-12-01 17:45:16 +01:00
Viresh Kumar 12a5105e04 mfd: stmpe: Get rid of irq_invert_polarity
Since the very first patch, stmpe core driver is using irq_invert_polarity as
part of platform data. But, nobody is actually using it in kernel till now.

Also, this is not something part of hardware specs, but is included to cater
some board mistakes or quirks.

So, better get rid of it. This is earlier discussed here:

https://lkml.org/lkml/2012/11/27/636

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-11-30 11:54:51 +01:00
Randy Dunlap 20d5c7defc mfd: Fix stmpe.c build when OF is not enabled
Fix build errors when CONFIG_OF is not enabled by including
<linux/of.h> (needs to be added in any case).
An alternative fix could be to make the driver depend on OF.

drivers/mfd/stmpe.c:1025:2: error: implicit declaration of function 'of_property_read_u32'
drivers/mfd/stmpe.c:1030:2: error: implicit declaration of function 'for_each_child_of_node'
drivers/mfd/stmpe.c:1030:36: error: expected ';' before '{' token

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-11-26 22:05:15 +01:00
Lee Jones b20a43715e mfd: Simplify IRQ domain registration code in STMPE
Historically, a driver would have to decide whether it required
a Linear or Legacy IRQ domain when registering one. This can end
up as quite a lot of code. A new Simple call now exists which
simplifies this process. Let's make use of it here.

Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-11-26 12:11:21 +01:00
Dmitry Torokhov 6ea32387a0 Input: stmpe-keypad - add support for Device Tree bindings
This patch allows the STMPE driver to be successfully probed and
initialised when Device Tree support is enabled. Besides the usual
platform data changes, we also separate the process of filling in
the 'in use' pin bitmap, as we have to extract the information from
Device Tree in the DT boot case.

Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2012-11-24 00:21:49 -08:00
Viresh Kumar cb5faba951 mfd: stmpe: Use devm_*() routines
This patch frees stmpe driver from tension of freeing resources.
devm_* derivatives of multiple routines are used while allocating resources,
which would be freed automatically by kernel.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-11-23 12:03:17 +01:00
Vipul Kumar Samar 037db524a2 Input: stmpe-ts - add DT support for stmpe touchscreen
This patch allows the STMPE Touchscreen driver to be successfully probed and
initialised when Device Tree support is enabled. Bindings are mentioned in
Documentation too.

Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2012-11-22 23:47:09 -08:00
Lee Jones 909582caae mfd: Enable the STMPE MFD for Device Tree
This patch allows the STMPE Multi-Functional Device to be correctly
initialised when booting with Device Tree support enabled. Its
children are specified by the addition of subordinate devices to the
STMPE node in the Device Tree file.

Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-11-11 23:35:03 +01:00
Lee Jones 5204e51d30 mfd: Correct copy and paste mistake in stmpe
When specifying IRQ numbers for the stmpe1601, IRQ defines for the
stmpe24xx were used instead. Fortunately, the defined numbers are
the same, hence why it survived testing. This fix is merely an
aesthetic one.

Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-11-11 23:35:03 +01:00
Lee Jones 76f93992e4 mfd: Provide the STMPE driver with its own IRQ domain
The STMPE driver is yet another IRQ controller which requires its
own IRQ domain. So, we provide it with one.

Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-11-11 23:35:03 +01:00
Lee Jones 7da0cbfc54 mfd: Prevent STMPE from abusing mfd_add_devices' irq_base parameter
Originally IRQ incrementers were provided in some template resource
structures for keypad and touchscreen devices. These were passed as
IORESOURCE_IRQs to MFD core in the usual way. The true device IRQs
were instead added to the irq_base when mfd_add_devices was invoked.
This is clearly an abuse of the call, and does not scale when IRQ
Domains are brought into play. Before we can provide the STMPE with
its own IRQ Domain we must first fix this. This patche keeps most
of the driver's structure, keeping the template strategy. However,
instead of providing the IRQ as an increment to irq_base, we
dynamically populate the IORESOURCE_IRQ with the correct device IRQ.

Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-11-11 23:35:03 +01:00
Mark Brown 0848c94fb4 mfd: core: Push irqdomain mapping out into devices
Currently the MFD core supports remapping MFD cell interrupts using an
irqdomain but only if the MFD is being instantiated using device tree
and only if the device tree bindings use the pattern of registering IPs
in the device tree with compatible properties.  This will be actively
harmful for drivers which support non-DT platforms and use this pattern
for their DT bindings as it will mean that the core will silently change
remapping behaviour and it is also limiting for drivers which don't do
DT with this particular pattern.  There is also a potential fragility if
there are interrupts not associated with MFD cells and all the cells are
omitted from the device tree for some reason.

Instead change the code to take an IRQ domain as an optional argument,
allowing drivers to take the decision about the parent domain for their
interrupts.  The one current user of this feature is ab8500-core, it has
the domain lookup pushed out into the driver.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-09-15 23:22:04 +02:00
Chris Blair e31f9b8264 mfd: Add support for no-interrupt stmpe config
Adds support for boards which have an STMPE device without the
interrupt pin connected.

Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Tested-by: Michel Jaouen <michel.jaouen@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-03-06 18:46:38 +01:00
Samuel Ortiz 8ad1a973f9 mfd: Fix stmpe section mismatch
This fixes:

WARNING: drivers/built-in.o(.text+0xf368f): Section mismatch in reference from
the function stmpe_probe() to the function .devinit.text:stmpe_chip_init()
The function stmpe_probe() references the function __devinit stmpe_chip_init().

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-01-09 00:37:45 +01:00
Samuel Ortiz dba61c8f4f mfd: Fix stmpe build warning
This fixes:

drivers/mfd/stmpe.c:114:1: warning: data definition has no type or storage
class [enabled by default]
drivers/mfd/stmpe.c:114:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Wimplicit-int]

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-01-09 00:37:45 +01:00
Viresh Kumar 7f7f4ea15e mfd: Add support for stmpe variant 801
STMPE801 is a GPIO expander. Registers for 801 are much different from other
variants. This patch adds support for STMPE801 in stmpe mfd driver.

Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-01-09 00:37:44 +01:00
Viresh Kumar 1cda2394e9 mfd: Add support for stmpe variant 610
STMPE610 is very much like STMPE811, except the number of gpio pins, which is 8
in 811 and 6 in 610. This patch adds support for variant 610. STMPE610 will
share most of the code with STMPE811.

Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-01-09 00:37:43 +01:00
Viresh Kumar 1a6e4b7415 mfd: Separate out STMPE controller and interface specific code
Few STMPE controller can have register interface over SPI or I2C. Current
implementation only supports I2C and all code is present in a single file
stmpe.c. It would be better to separate out I2C interface specific code from
controller specific code. Later SPI specific code can be added in a separate
file.

This patch separates out I2C and controller specific code into separate files,
making stmpe.c independent of I2C.

Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-01-09 00:37:42 +01:00
Viresh Kumar 73de16db43 mfd: Add support for irq over gpio pin to stmpe
On many boards, stmpe is present as an separate device (not as part of SoC).
Here gpio lines are mostly used for getting interrupts. This patch adds in
support to handle irq over gpio pin.

Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-01-09 00:37:29 +01:00