The '\n' at the end of the format string is not needed. It adds an extra
line break when doing
cat /proc/interrupts
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The slot_width is for essentially same thing. Instead of storing
bclk_lrclk_ratio, just store the slot_width. Comments has been updated
accordingly and some variable names changed to more descriptive.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Implements set_tdm_slot() callback for mcasp. Channel constraints are
updated according to the configured tdm mask and slots each time
set_tdm_slot() is called. The special case when slot width is set to
zero is allowed and it means that slot width is the same as the sample
width.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TX and RX direction share the same bit clock and frame sync, so
the samplerate must be the same to both directions.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The FIFO threshold for McASP should be <=[tx/rx]numevt so the initial value
for the refining should meet this requirement as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_ioremap_resource() instead of open code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use resource managed function devm_snd_soc_register_component for
component registration instead of snd_soc_register_component.
Also, remove davinci_vcif_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Find the configured DMA controller by asking for a DMA channel in the
probe phase and releasing it right after. The controller device can be
found via the dma_chan struct and the controller is recognized from
the compatible property of its device node. The patch assumes EDMA if
there is no device node.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The default state when serializers are in inactive slots is Hi-Z.
In some cases, there are no additional components driving the data
lines to a safe state so they might have noise.
While in inactive slots, the McASP AXR pins configured as outputs
can be driven low through the serializer pin drive mode setting
(DISMOD) to prevent such noise.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_enabled() will only tell if the pm runtime has been enabled for
the device, which is done at probe time but will not tell the actual power
state of the device.
pm_runtime_active() provides this information.
This patch fixes a kernel crash when doing suspend when McASP is not
active.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to copy the list of all supported sample-rates.
Finding the supported endpoints within the current range is enough
(see snd_interval_list()).
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set channel count constraints for multiple serializers case. On McASP
the active channels mask is the same for all the serializers. With the
current implementation this means that if more than one serializers is
used, all TDM slots have to be active on all serializers. The patch
sets the channel count constraints according to number of RX and TX
serializers.
Reported-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The McASP driver currently always sends as many slots or channels to a
i2s-wire as there are configured tdm_slots (see mcasp_i2s_hw_param()).
Thus the BLCK rate does not depend on the amount of channels, just the
configure amount of tdm-slots.
Reported-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A selection of changes for v4.1 so far. The main things are:
- Move of jack registration to the card where it belongs.
- Support for DAPM routes specified by both the machine driver and DT.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU960DAAoJECTWi3JdVIfQkKIH/RDvxRn8dvKOPF5U9Uix3chH
JWKkzqfsMP0EpmQTzCQPp0ShAyYcWSbYsopicynPxUem5vS4Z8+UmOgEEgkj59pK
USbF6v1jCQXA6BcbKyUcRRBD9FtRkfVDc7mYbRs2CcwQz2CGCgee41cvPM+2BT+z
QdNC9UJARSweGvE1IUJSfpfYOly+BJ2s0/28RaQ0PGt+I0auoYx7IMFgMSDjv2p6
PY0kyQiwm3Kyj2uNXPZ5gEuPxlw/t8n4fbQNrBYAvxzN+EF5NrGdKE3N7MI1xRV/
EkFhzy+uM3X9c37tb2lT2fgPFlBc9rgPuLPSyoQ6nxa5ghCqAlgRhzpxRem8hhU=
=VlCw
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.1' into asoc-next
ASoC: Changes for v4.1
A selection of changes for v4.1 so far. The main things are:
- Move of jack registration to the card where it belongs.
- Support for DAPM routes specified by both the machine driver and DT.
# gpg: Signature made Thu 05 Mar 2015 01:10:27 GMT using RSA key ID 5D5487D0
# gpg: WARNING: digest algorithm MD5 is deprecated
# gpg: please see https://gnupg.org/faq/weak-digest-algos.html for more information
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
The dapm field of the snd_soc_codec struct will eventually be removed
(replaced with the DAPM context from the component embedded inside the
CODEC). Replace its usage with the card's DAPM context. The idea is that
DAPM is hierarchical and with the card at the root it is possible to access
widgets from other contexts through the card context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Passing &mcasp->ruledata[dir] to snd_pcm_hw_rule_add() is not correct since
commit:
7b3d165a28 ASoC: davinci-mcasp: Index ruledata in drvdata with substream->stream
now sets up the struct based on the substream->stream (0 or 1) while we pass
a pointer which we take with dir (1 or 2). This will lead kernel crash.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The serializer direction definitions runs from 1 to 2, which does not
suite the purpose. The substream->stream is perfect for the purpose
and should have been used from the beginning.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As davinci card gets registered using 'devm_' api
there is no need to unregister the card in 'remove'
function.
Hence drop the 'remove' function.
Fixes: ee2f615d6e (ASoC: davinci-evm: Add device tree binding)
Signed-off-by: Manish Badarkhe <manishvb@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Set rule constraints to allow only combinations of sample-rate,
sample-format, and channels counts that can be played/captured with
reasonable sample-rate accuracy.
The logic with tdm-slots and serializers (=i2s data wires) goes like
this: The first wire will take all channels up to number of tdm-slots,
before following wires (if any) are used. If the first wire is used
fully, the remaining wires share the same clocks and the divider can
be calculated for the first wire.
Also, takes the number of tdm-slots into account when implicitly
selecting the BLCK divider.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduced by commit:
6afda7f507 ASoC: davinci-mcasp: Allow complete shutdown of McASP when not in use
I'm really sorry for this...
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rearrange the pm_runtime_get/put_sync calls so the IP will be turned off
when it is not in use.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All DAI drivers has been converted to use edma-pcm instead of davinci-pcm
and the driver can be removed from the tree.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The edma-pcm performs as good as the old davinci-pcm and it's use does not
require the 'ping-pong' mode of davinci-pcm, which was introduced to
overcome under/over flow issues when using davinci-pcm.
Keep the SND_DAVINCI_SOC config option to select the SND_EDMA_SOC to avoid
regression in audio support.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The edma-pcm can replace the old davinci-pcm as platform driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The edma-pcm can replace the old davinci-pcm as platform driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
edma-pcm going to replace davinci-pcm as platform driver for daVinci
platform.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Support for setups where codec is bitclock slave and frame master.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
One of the McASP instances in DM646x line of DMSoC only supports DIT mode.
This means that the given IP does not have support for rx and all the rx
related resources are missing, like irq and DMA request.
The driver should not fail if any or all of the RX resource is missing
when the op_mode is set to DIT mode.
Since RX is not possible in DIT mode, we can just ignore the rx resources
when the McASP is used in DIT mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On DA830 devices McASP0,1 and 2 shares a single combined interrupt request
line.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The machine driver has no business with the underlying dma.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
An earlier bug fix of mine made the SND_DM365_VOICE_CODEC symbol
tristate to avoid creating an undefined reference from the
davinci-vcif.c driver to the davinci_soc_platform_register
function that may be in a module.
However, this may now lead to a different error on randconfig
kernels:
"warning: SND_DM365_VOICE_CODEC creates inconsistent choice state"
This happens because we now have a choice statement with
one bool and one tristate option, and the latter might not
support being set to 'y' because of dependencies.
This new change turns the other option into 'tristate' as well,
which avoids the problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 19926c6de0 ("ASoC: davinci: vcif must be a module if SND_DAVINCI_SOC is")
Signed-off-by: Mark Brown <broonie@kernel.org>
Some SoC, like da850/OMAP-L138 uses one common interrupt request for TX/RX
events.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
An underrun (playback) event occurs when the serializer transfer
data from the XRBUF buffer to the XRSR shift register, but the
XRBUF hasn't been filled. Similarly, the overrun (capture) event
occurs when data from the XRSR shift register is transferred to
the XRBUF but it hasn't been read yet.
These events are handled as XRUN events that cause the pcm to stop.
The stream has to be explicitly restarted by the userspace which
ensures that after stopping/starting McASP the data transfer is
aligned with DMA. The other possibility was to internally stop and
start McASP without DMA even knowing about it.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Active slots count depends on the number of channels in the stream
and the number of active serializers. Each serializer will handle
at most the number of channels specified via 'tdm-slots' parameter
in DT.
There are two possible scenarios:
- Single serializer: channel count fits in the max slots supported by
McASP serializers, active slots is same as channel count
- Multiple serializers: channel count is bigger than max slots supported
by a serializer. Channel count determines how many serializers are
needed at their max slot count configuration
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In IIS (I2S, TDM, etc) mode the maximum number of allowed channels for
either direction can be:
number of serializers for the direction * tdm_slots.
This constraint applicable for the first stream, while consequent stream
should not have more channels then the first stream.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of validating the tdm_slots parameter every time at hw_params we
can do it once during probe. If the parameter is not valid (<2 or >32)
print an error and fix it up.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the bus is configured to have more BCLK then the data type demands we
need to use the rotation to move the data to correct place.
Reported-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In IIS mode the tx and rx configuration is symmetric, the BCLK and FSYNC is
shared.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If probe fails then we need to call pm_runtime_disable() to balance
out the previous pm_runtime_enable() call.
Signed-off-by: Anil Kumar <anilk4.v@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In this way the start code for tx/rx going to be located at the same place.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AFIFO should not be stopped (or started for that matter) when McASP is
running since it can cause unpredictable issues because we are switching off
AFIFO for the direction which was handling the requests from McASP and was
generating DMA request toward the system DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Follow the sequence described in the TRMs when starting RX.
Write to RXBUF register was not correct and there is no need to release the
RX state machine/Receive frame sync generator twice.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown