Radiotap was updated to include a "bad PLCP" flag and standardise
the "bad FCS" flag in the "flags" rather than "RX flags" field,
this patch updates Linux to that standard.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even though userland probably cannot submit packets, there might
still be some coming, and that's no good when the driver doesn't
expect them. Stop the queues across suspend/resume.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The last warning can never trigger, and the explicit AP_VLAN
check is pointless if we move the config_interface check down,
in practice config_interface is required anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AP mode currently sets up the dual stream capability
for all stations. This patch fixes it by checking if the
associated station supports dual stream MCS rates (8-15).
We would disregard any MCS rates above 15, since Atheros
HW supports only 0..15 rates currently, and can't receive
at rates > 15 anyway.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fills the ack_signal field in TX status with an appropriate
value from the TX descriptor.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should be checking with the 4K header and not the non-4K
header size.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We always return true, checking for 'false' return value
is bogus anyway, so fix this.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This improves readability. Handle both 4K/non-4K EEPROM
in this patch.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Print the EEPROM version/revision on init.
Choose appropriate debug masks on error conditions,
and remove useless print messages.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the PCI retry timeout code as that was just taken from ipw2100
due to historical reasons but in reality its a no-op, additionally its
simply incorrect as each PCI devices has its own custom PCI configuration
space on PCI config space >= 0x40. Not to mention we were trying to write
0 to a place that already has 0 on it.
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Ben Cahill <ben.m.cahill@intel.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Tested-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the TSF offset calculation for staggered Beacon frames
and sets ATH_BCBUF back to the earlier value 4 to enable multi-BSS
configurations of up to four BSSes.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a scan is queued in STA mode while the interface is in state direct
probe, authenticate or associate the scan is delayed until the interface
enters disabled or associated state. But in case of direct probe-,
authentication- or association- timeout sta_work will not be scheduled
anymore (without external trigger) and thus the pending scan is not
executed and prevents a new scan from being triggered (-EBUSY).
Fix this by queueing the sta work again after direct probe-, authentication-
and association- timeout.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No hw/driver actually supports more than four queues right now,
and we allocate a number of things per queue which means we
waste a bit of memory. Reduce the maximum number to four to
accurately reflect what we do (and need for QoS). Even if we
had hardware supporting more queues we couldn't take advantage
of that right now anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This inline is useless and actually makes the code _longer_
rather than shorter.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scan capability added to cfg80211/nl80211 introduced a
dependency on nl80211 by cfg80211. We can thus no longer have
just cfg80211 without nl80211. Specifically, cfg80211_scan_done()
calls nl80211_send_scan_aborted() or nl80211_send_scan_done().
Now we remove the option for user to select nl80211. It will always
be compiled if user selects cfg80211.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't call ieee80211_sta_find_ibss() directly, like it's done in STA
mode, so that the commit() call is more harmless respectively has
less site-effects.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For the fifteen bazillionth time.
See also commits f06da264cf and
aeb565dfc3 ("i915: Fix more size_t format
string warnings" and "Fix annoying DRM_ERROR() string warning").
Grr-target: Eric Anholt <eric@anholt.net>
Grr-target: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (25 commits)
drm/i915: Fix LVDS dither setting
drm/i915: Check for dev->primary->master before dereference.
drm/i915: TV detection fix
drm/i915: TV mode_set sync up with 2D driver
drm/i915: Fix TV get_modes to return modes count
drm/i915: Sync crt hotplug detection with intel video driver
drm/i915: Sync mode_valid/mode_set with intel video driver
drm/i915: TV modes' parameters sync up with 2D driver
agp/intel: Add support for new intel chipset.
i915/drm: Remove two redundant agp_chipset_flushes
drm/i915: Display fence register state in debugfs i915_gem_fence_regs node.
drm/i915: Add information on pinning and fencing to the i915 list debug.
drm/i915: Consolidate gem object list dumping
drm/i915: Convert i915 proc files to seq_file and move to debugfs.
drm: Convert proc files to seq_file and introduce debugfs
drm/i915: Fix lock order reversal in GEM relocation entry copying.
drm/i915: Fix lock order reversal with cliprects and cmdbuf in non-DRI2 paths.
drm/i915: Fix lock order reversal in shmem pread path.
drm/i915: Fix lock order reversal in shmem pwrite path.
drm/i915: Make GEM object's page lists refcounted instead of get/free.
...
When there are no free snums, UCC ethernet should gracefully fail, but
currently it oopses this way:
# ifconfig eth0 up
fill_init_enet_entries: Can not get SNUM.
ucc_geth_startup: Can not fill p_init_enet_param_shadow.
eth0: Cannot configure net device, aborting.
Unable to handle kernel paging request for data at address 0x00000190
Faulting instruction address: 0xc0294c88
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c0294c88] mutex_lock+0x0/0x1c
LR [c01b6be8] phy_stop+0x20/0x70
Call Trace:
[efb25da0] [efb2eb60] 0xefb2eb60 (unreliable)
[efb25db0] [c01b2058] ucc_geth_stop+0x2c/0x8c
[efb25dd0] [c01b4194] ucc_geth_open+0x48/0x27c
[efb25df0] [c020eec0] dev_open+0xc0/0x118
[...]
This is because the ucc_geth_stop() routine assumes that ugeth->phydev
is always initialized by the ucc_geth_open(), while it is not in case
of errors.
If we add a check to the ucc_geth_stop(), then another oops pops up:
Unable to handle kernel paging request for data at address 0x00000004
Faulting instruction address: 0xc01b46a4
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c01b46a4] adjust_link+0x20/0x1b4
LR [c01b770c] phy_state_machine+0xdc/0x44c
Call Trace:
[ef83bf10] [c021b388] linkwatch_schedule_work+0x74/0xf8 (unreliable)
[ef83bf40] [c01b770c] phy_state_machine+0xdc/0x44c
[ef83bf60] [c004c13c] run_workqueue+0xb8/0x148
[ef83bf90] [c004c870] worker_thread+0x70/0xd0
[ef83bfd0] [c00505fc] kthread+0x48/0x84
[ef83bff0] [c000f464] kernel_thread+0x4c/0x68
[...]
That one happens because ucc_geth_stop() does not call phy_disconnect()
and so phylib state machine is running without any idea that a MAC has
just died.
Also, when device tree specifies fixed-link, and CONFIG_FIXED_PHY
is disabled, we'll get this oops:
0:01 not found
eth2: Could not attach to PHY
eth2: Cannot initialize PHY, aborting.
Unable to handle kernel paging request for data at address 0x00000190
Faulting instruction address: 0xc02967d0
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c02967d0] mutex_lock+0x0/0x1c
LR [c01b6bcc] phy_stop+0x20/0x70
Call Trace:
[ef82be50] [efb6bb60] 0xefb6bb60 (unreliable)
[ef82be60] [c01b2058] ucc_geth_stop+0x2c/0x8c
[ef82be80] [c01b4194] ucc_geth_open+0x48/0x27c
[ef82bea0] [c0210a04] dev_open+0xc0/0x118
[ef82bec0] [c020f85c] dev_change_flags+0x84/0x1ac
[ef82bee0] [c037b768] ic_open_devs+0x168/0x2bc
[ef82bf20] [c037ca98] ip_auto_config+0x90/0x28c
[ef82bf60] [c0001b9c] do_one_initcall+0x34/0x1a0
[ef82bfd0] [c035e240] do_initcalls+0x38/0x58
[ef82bfe0] [c035e2c4] kernel_init+0x30/0x90
[ef82bff0] [c000f464] kernel_thread+0x4c/0x68
[...]
And again, ucc_geth_stop() assumes that ugeth->phydev is there, while
it isn't.
This patch fixes all three oopses simply by rearranging some code:
- In ucc_geth_open(): move init_phy() call to the beginning, so
that we only call ucc_geth_stop() with a PHY attached;
- Move phy_disconnect() call from ucc_geth_close() to
ucc_geth_stop(), so that we'll always disconnect the PHY.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inline function skb_gro_mac_header defined in include/linux/netdevice.h
makes use of page_address(). Depending on configuration options, the latter
is either defined as a macro or is declared as a function in another header
file, namely include/linux/mm.h. However, include/linux/netdevice.h does not
include include/linux/mm.h.
On MIPS, this has produced the following build error:
CC kernel/sysctl_check.o
In file included from include/linux/icmpv6.h:173,
from include/linux/ipv6.h:208,
from include/net/ip_vs.h:26,
from kernel/sysctl_check.c:6:
include/linux/netdevice.h: In function 'skb_gro_mac_header':
include/linux/netdevice.h:1132: error: implicit declaration of function
'page_address'
include/linux/netdevice.h:1133: warning: pointer/integer type mismatch
in conditional expression
make[1]: *** [kernel/sysctl_check.o] Error 1
make: *** [kernel] Error 2
The patch adds the missing include and fixes the build error.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bdb_lvds_options structure according to its defination in
2D driver. Then we can parse and set 'lvds_dither' bit correctly
on non-965 chips.
Signed-off-by: Li Peng <peng.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
I've hit the occasional oops inside i915_wait_ring() with an indication of
a NULL derefence of dev->primary->master. Adding a NULL check is
consistent with the other potential users of dev->primary->master.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Check that the encoder has a real enabled crtc for TV detect, and fix
missing TV type setting after detect.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Fix TV control save register for untouched bits, and color
knobs different definition for 945 and 965 chips.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The get_modes hook must return the number of modes added. This also fixes
TV mode's clock calculation int overflow issue, and use 0.01 precision for
mode refresh validation.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This covers:
Use long crt hotplug activation time on GM45.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This covers:
Limit CRT DAC speed better.
and also clears the border color in case it's set to some garbage, which would
fix ugly outlines in the blank regions of the CRT.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
[anholt: replaced *drm_dev with *dev]
Signed-off-by: Eric Anholt <eric@anholt.net>
This covers at least:
TV: subcarrier fix for NTSC and PAL
TV: fix timing parameters for PAL, 480p, 1080i
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
agp_chipset_flush() is for flushing the intel GMCH write cache via the
IFP, these two uses are for when we're getting the object into the cpu
READ domain, and thus should not be needed. This confused me when I was
getting my head around the code.
With thanks to airlied for helping me check my mental picture of how the
flushes and clflushes are supposed to be used.
Signed-off-by: Owain G. Ainsworth <oga@openbsd.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This was inspired by a patch by Chris Wilson, though none of it applied in any
way due to the debugfs work and I decided to change the formatting of the
new information anyway.
Signed-off-by: Eric Anholt <eric@anholt.net>
Here we eliminate a few functions in favor of using a single function
to dump from all of the object lists.
Signed-Off-By: Ben Gamari <bgamari@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The old mechanism to formatting proc files is extremely ugly. The
seq_file API was designed specifically for cases like this and greatly
simplifies the process.
Also, most of the files in /proc really don't belong there. This patch
introduces the infrastructure for putting these into debugfs and exposes
all of the proc files in debugfs as well.
Signed-off-by: Ben Gamari <bgamari@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-quota-2.6: (27 commits)
ext2: Zero our b_size in ext2_quota_read()
trivial: fix typos/grammar errors in fs/Kconfig
quota: Coding style fixes
quota: Remove superfluous inlines
quota: Remove uppercase aliases for quota functions.
nfsd: Use lowercase names of quota functions
jfs: Use lowercase names of quota functions
udf: Use lowercase names of quota functions
ufs: Use lowercase names of quota functions
reiserfs: Use lowercase names of quota functions
ext4: Use lowercase names of quota functions
ext3: Use lowercase names of quota functions
ext2: Use lowercase names of quota functions
ramfs: Remove quota call
vfs: Use lowercase names of quota functions
quota: Remove dqbuf_t and other cleanups
quota: Remove NODQUOT macro
quota: Make global quota locks cacheline aligned
quota: Move quota files into separate directory
ext4: quota reservation for delayed allocation
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: fix length calculation in compat code
dlm: ignore cancel on granted lock
dlm: clear defunct cancel state
dlm: replace idr with hash table for connections
dlm: comment typo fixes
dlm: use ipv6_addr_copy
dlm: Change rwlock which is only used in write mode to a spinlock
This introduces allocation in the batch submission path that wasn't there
previously, but these are compatibility paths so we care about simplicity
more than performance.
kernel.org bug #12419.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Keith Packard <keithp@keithp.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Like the GTT pwrite path fix, this uses an optimistic path and a
fallback to get_user_pages. Note that this means we have to stop using
vfs_write and roll it ourselves.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We've wanted this for a few consumers that touch the pages directly (such as
the following commit), which have been doing the refcounting outside of
get/put pages.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since the pagefault path determines that the lock order we use has to be
mmap_sem -> struct_mutex, we can't allow page faults to occur while the
struct_mutex is held. To fix this in pwrite, we first try optimistically to
see if we can copy from user without faulting. If it fails, fall back to
using get_user_pages to pin the user's memory, and map those pages
atomically when copying it to the GPU.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This fixes incorrect detection of the second SDVO/HDMI output on G4X, and
extra boot time on pre-G4X.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
