pllx_bypass_src mux shouldn't be the parent of pllx clock
since it's only valid when when pllx BYPASS bit is set.
Thus it is actually one parent of pllx_bypass only.
Instead, pllx parent should be fixed to osc according to
reference manual.
Other plls have the same issue.
e.g. before fix, the pll tree is:
osc 6 6 24000000 0 0
pll1_bypass_src 0 0 24000000 0 0
pll1 0 0 792000000 0 0
pll1_bypass 0 0 792000000 0 0
pll1_sys 0 0 792000000 0 0
After the fix, it's:
osc 6 6 24000000 0 0
pll1 0 0 792000000 0 0
pll1_bypass 0 0 792000000 0 0
pll1_sys 0 0 792000000 0 0
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
commit ee36027427 ("clk: imx: Add clock support for imx6qp")
introduced a regression due to a subtle typo in the 'can_root' clock
definition. The effect is that trying to configure the bitrate of the
can interfaces fails with -EDOM or produces a division by zero error
due to the clock_freq of the can serial clock being reported as '0'.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Fixes: ee36027427 ("clk: imx: Add clock support for imx6qp")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
most of the clock tree structures on i.MX6 Quad Plus are
same as on i.MX6Q. there still some differences between
these two SOCs. compared to the i.XM6Q, the differents of
clocks on i.MX6QP is mainly on:
1. New clock gate added to support the PRE and PRG modules
2. 24MHz OSC clock option added to the UART, IPG, ECSPI, and
CAN clock roots.
3. MMDC channel 1 clock gate is now controllable.
4. clock gating added to the LDB_DIx_IPU clocks on i.MX6QP
5. EMI clock root divider fix
6. other updates fo CSCMRx, CSCDRx and CS2CDR registers.
detailed infomation, please refer to the i.MX6QP RM.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Correct SPDIF clock setting issue in clock tree, the SPDIF_GCLK is also
one clock of SPDIF, which is missed before.
We found an issue that imx can't enter low power mode with spdif
if IMX6x_CLK_SPDIF is used as the core clock of spdif. Because
spdif driver will register IMX6x_CLK_SPDIF clock to regmap, regmap will do
clk_prepare in init function, then IMX6x_CLK_SPDIF clock is prepared in probe,
so its parent clock (PLL clock) is prepared, the prepare operation of
PLL clock is to enable the clock. But I.MX needs all PLL clock is disabled,
then it can enter low power mode.
So we can't use IMX6x_CLK_SPDIF as the core clock of spdif, the correct spdif
core clock is SPDIF_GCLK, which share same gate bit with IMX6x_CLK_SPDIF clock.
SPDIF_GCLK's parent clock is ipg clock.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make sure to keep UART clocks enabled during kernel init if
earlyprintk or earlycon are active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add CAAM clock support to the i.MX6 clocking infrastructure.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently it is not possible to use HDMI and LVDS at the same time on a
imx6dl-sabresd board.
Fix this usecase by setting IMX6QDL_CLK_PLL3_PFD1_540M to 540MHz and
also by setting it as the parent of IMX6QDL_CLK_IPU1_SEL.
Based on the configuration done in the FSL kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to IMX6D/Q RM, table 18-3, sata clock's parent is ahb, not ipg.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
After the cleanup on clock drivers, they are now ready to be moved into
drivers/clk. Let's move them into drivers/clk/imx folder.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
