Even if this spdif input driver is only supposed to be used on 64bits
platform, there is possible problem with 32bits and do_div, as reported
by the kbuild robot. Just fix it.
Fixes: 5ce5658375 ("ASoC: meson: add axg spdif input")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add error logs to make probe debug easier.
Also remove hard-coded dependency on NHLT. NHLT literally stands for
NonHdaudioLinkTable and is only required for SSP/DMIC interfaces.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
bus->ppcap is now tested upfront, there is no need to re-check if the
hardware is exposed as needed. Remove tests and remove indentation.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check immediately if required HDaudio capabilities can't be found (no
PPCAP or no streams exposed in GCAP), and move all DMA inits after the
error tests.
PPCAP and GCAP are not reliable indicators of DSP presence, but if
they don't exist then the driver will not work.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The existing PPCAP and GCAP fields cannot be used reliably to
determine if the DSP is enabled by the BIOS. Instead rely on the
class/subclass information to find out if this driver can run or
not. The values in the code don't seem to be documented in publicly
available documents but are part of recommendations made to BIOS
writers and have been verified to be accurate on a number of
platforms.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's with CNP, supposed to be equivalent with CNL entry.
Keep the existing declaration style for now, at a later point we may
transition and use PCI_DEVICE_DATA().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I2S IP instance can work in transmitter/playback or receiver/capture mode
exclusively. The patch registers corresponding instance as ASoC component
with audio framework.
Signed-off-by: Maruthi Srinivas Bayyavarapu <maruthi.srinivas.bayyavarapu@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The new Dell IoT platform uses kabylake + alc3277 codec, and alc3277
shares the driver with the codec rt5660, here we generate a new
machine driver based on kbl_da7219_max98357a.
The audio design on this IoT platform is as below:
- Intel kabylake platform
- connect the codec ALC3277 via SSP0
- line-out and line-in with Micbias jacks
- line-out mute control and jack detection of line-out and line-in
- two HDMI ports with audio capability
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the spdif input decoder of the axg SoC family
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
add IEC958_SUBFRAME_LE to the list of format accepted by the fifo frontend.
As opposed to what was initially noted in the toddr dai driver, the spdifin
does not place the msb at bit 28, it just output a whole spdif subframe.
Placing the msb at bit 28 in the toddr driver just filters out the parity,
user, channel status and validity bits. It is better to just provide the
whole spdif subframe to the userspace and let the iec958 plugin deal with
it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 4fb7f4df49 ("ASoC: simple-card: use cpu/codec pointer on
simple_dai_props") updated {cpu,codec}_dai to be pointers in struct
simple_dai_props but didn't update these locations to dereference the
pointers.
This patch fixup it for non DT simple-card use case.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
eukrea-tlv320.c machine driver runs on non-DT platforms
and include <asm/mach-types.h> header file in order to be able
to use some machine_is_eukrea_xxx() macros.
Building it for ARM64 causes the following build error:
sound/soc/fsl/eukrea-tlv320.c:28:10: fatal error: asm/mach-types.h: No such file or directory
Avoid this error by not allowing to build the SND_SOC_EUKREA_TLV320
driver when ARM64 is selected.
This is needed in preparation for the i.MX8M support.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of Huawei laptops come with a LED in the micmute key. This patch
enables the use of micmute LED for these devices:
1. Matebook X (19e5:3200), (19e5:3201)
2. Matebook X Pro (19e5:3204)
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ayman Bagabas <ayman.bagabas@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch solves bug 200501 'Only 2 of 4 speakers playing sound.'
It enables the front speakers on Huawei Matebook X Pro laptops.
These laptops come with Dolby Atmos sound system and these pins
configuration enables the front speakers.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200501
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ayman Bagabas <ayman.bagabas@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
stream is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
sound/core/pcm.c:140 snd_pcm_control_ioctl() warn: potential spectre issue 'pcm->streams' [r] (local cap)
Fix this by sanitizing stream before using it to index pcm->streams
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
info.mode and info.port are indirectly controlled by user-space,
hence leading to a potential exploitation of the Spectre variant 1
vulnerability.
These issues were detected with the help of Smatch:
sound/synth/emux/emux_hwdep.c:72 snd_emux_hwdep_misc_mode() warn: potential spectre issue 'emu->portptrs[i]->ctrls' [w] (local cap)
sound/synth/emux/emux_hwdep.c:75 snd_emux_hwdep_misc_mode() warn: potential spectre issue 'emu->portptrs' [w] (local cap)
sound/synth/emux/emux_hwdep.c:75 snd_emux_hwdep_misc_mode() warn: potential spectre issue 'emu->portptrs[info.port]->ctrls' [w] (local cap)
Fix this by sanitizing both info.mode and info.port before using them
to index emu->portptrs[i]->ctrls, emu->portptrs[info.port]->ctrls and
emu->portptrs.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current rsnd is using RSND_REG_xxx for register naming,
and using RSND_REG_##f style macro for read/write.
The biggest reason why it uses this style is that
we can avoid non-existing register access.
But, its demerit is sequential register access code will
be very ugly.
Current rsnd driver is well tested, so, let's remove RSND_REG_
from rsnd_reg, and cleanup sequential register access code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fireface 800 is a flagship model of RME GmbH for audio and music units
on IEEE 1394 bus, shipped 2004. This model consists of four chips:
- TI TSB81BA3D for physical layer on cable environment of EEE 1394 bus
- TI TSB82AA2 for link layer for 1394 OHCI bus bridge to PCI bus
- Xilinx Spartan-3 FPGA XC3S400
- Xilinx High-Performance CPLD XC9572XL
This commit adds support Fireface 800. In this time, the support is
restricted to its MIDI functionality, thus this commit adds some
condition statements to avoid touching streaming functionality.
Unlike Fireface 400, Fireface 800 has no functionality to suppress
asynchronous transactions for MIDI messages except for unregister of
listen address in controller side, thus the feature is available as is.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Content of asynchronous transaction for MIDI messages differs between
Fireface 400 and 800.
This commit adds a model-specific handler for the transaction and adds
arrangement.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireface 400 and 800 have the same mechanism to decide address to which
asynchronous transactions are sent for MIDI messages, however they use
different registers for controllers to notify higher 4 byte of the
address.
This commit adds a model-specific parameter to represent the address.
Additionally, it corrects some comments. I note that these two models have
a difference to enable/disable the transaction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As long as investigating packet dumps from Fireface 400/800, a register
to receive asynchronous transactions for MIDI messages is the same. For
Fireface 800, minor register is used.
This commit declares macros for the transactions and obsoletes
model-specific parameters.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unlike Fireface 400, Fireface 800 have two pair of optical interface
for ADAT signal and S/PDIF signal. ADAT signals for the interface
are handled for sampling clock source separately.
This commit modifies a parser for clock configuration to distinguish
these two ADAT signals.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As long as investigating packet dumps from Fireface 400/800, bits on
status registers for clock synchronization are the same.
This commit moves a parser for a register of clock configuration to
obsolete model-specific operations.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As long as investigating packet dumps from Fireface 400/800, bits on
status registers for clock synchronization are the same.
This commit moves a parser for the registers to obsolete model-specific
operations.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As long as investigating packet dumps from Fireface 400/800, status
registers for clock synchronization is common.
This commit moves some macros for them to header file.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current simple-scu-card didn't care about codec_conf
for multi DPCM case. This patch cares it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In DPCM case, it uses CPU-dummy / dummy-Codec dai links, and
non DPCM case, it uses CPU-Codec dai links.
Now, we want to merge simple-card and simple-scu-card.
These sound cards are using silimar but not same logic on each functions.
Then, of course we want to share same logic.
To compromise, this patch uses cpu/codec pointer on simple-scu-card.
It is same logic with simple-card, thus easy merging.
This is prepare for merging simple card
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
simple-scu-card.c is supporting "convert-rate/channels" which is
used for DPCM.
But, sound card might have multi codecs, and each codec might need
each convert-rate/channels.
This patch supports each codec's convert-rate/channles support.
top node convert-rate/channels will overwrite settings if exist.
It can't support each codec's convert-rate/channels if sound card had
multi codecs without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In DPCM case, it uses CPU-dummy / dummy-Codec dai links.
If sound card is caring only DPCM, link count = dai count,
but, if non DPCM case, link count != dai count.
Now, we want to merge simple-card and simple-scu-card,
then, we need to care both link / dai count more carefly
This patch cares it, and prepare for merging simple card
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
simple-card is supporting dai-link support, but simple-scu-card
doesn't have it.
This patch support it. This is prepare for merging simple-card
and simple-scu-card.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When building without CONFIG_PCI, we can (depending on the architecture)
get a link failure:
ERROR: "pci_iounmap" [sound/pci/hda/snd-hda-codec-ca0132.ko] undefined!
Adding a compile-time check for PCI gets it to work correctly on
32-bit ARM.
Fixes: d99501b857 ("ALSA: hda/ca0132 - Call pci_iounmap() instead of iounmap()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've excluded the display_power_control flag for Intel HSW and BDW
codecs as the HD-audio controllers of the corresponding platforms take
care of the display power as well. But the recent refactoring
separates the controller and the codec power accounting, so it's fine
to call the display PM even for HSW/BDW codecs. This is less
confusing since we can avoid this well-hidden condition.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The display power is in unbalance at removing the driver since it
misses the snd_hdac_display_power(OFF) call.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After the recent refactoring, snd_hdac_display_power() doesn't return
any error, hence it can be defined to return void.
This makes many error checks redundant and allows us to reduce them
gracefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When an error occurs in azx_probe_continue(), we should release the
display power. However, the current code ignores it and releases the
display power only for HSW/BDW cases. Fix it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hdac_display_power() can be called even for a HDA controller
without DRM binding. The same is true for other helpers,
snd_hdac_i915_set_bclk() and snd_hdac_set_codec_wakeup().
So all superfluous AZX_DCAPS_I915_POWERWELL checks in hda_intel.c can
be dropped, and the definition of AZX_DCAPS_I915_POWERWELL itself can
be removed as well. This simplifies the code a lot.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current HD-audio code manages the DRM audio power via too complex
redirections, and this seems even still unbalanced in a corner case as
Intel DRM CI has been intermittently reporting. This patch is a big
surgery for addressing the complexity and the possible unbalance.
Basically the patch changes the display PM in the following ways:
- Both HD-audio controller and codec drivers call a single helper,
snd_hdac_display_power(). (Formerly, the display power control from
a codec was done indirectly via link_power bus ops.)
- snd_hdac_display_power() receives the codec address index. For
turning on/off from the controller, pass HDA_CODEC_IDX_CONTROLLER.
- snd_hdac_display_power() doesn't manage refcounts any longer, but
keeps the power status in bitmap. If any of controller or codecs is
turned on, the function updates the DRM power state via get_power()
or put_power().
Also this refactor allows us more cleanup:
- The link_power bus ops is dropped, so there is no longer indirect
management, as mentioned in the above.
- hdac_device link_power_control flag is moved to hda_codec
display_power_control flag, as it's only for HDA legacy.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106525
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current simple-scu-card driver is parsing codec position for DPCM
and consider DAI format. But, current operation is doing totally pointless,
because it should be called for each CPU/Codec pair.
Let's tidyup asoc_simple_card_parse_daifmt() timing.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In DPCM case, it uses CPU-dummy / dummy-Codec dai links, and
non DPCM case, it uses CPU-Codec dai links.
Now, we want to merge simple-card and simple-scu-card.
These sound cards are using silimar but not same logic on each functions.
Then, of course we want to share same logic.
To compromise, this patch uses cpu/codec pointer on simple-card.
It is same logic with simple-scu-card, thus easy merging.
This is prepare for merging audio card
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When CONFIG_OF is disabled, of_graph_parse_endpoint() does not
initialize 'info', and gcc can see that:
sound/soc/generic/simple-card-utils.c: In function 'asoc_simple_card_parse_graph_dai':
sound/soc/generic/simple-card-utils.c:284:13: error: 'info.port' may be used uninitialized in this function [-Werror=maybe-uninitialized]
It's probably best to check the return code anyway, and that also
takes care of the warning.
Fixes: b6f3fc005a ("ASoC: simple-card-utils: fixup asoc_simple_card_get_dai_id() counting")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Calling into the codec driver adds a dependency on that being reachable
from the module:
ERROR: "rt5663_sel_asrc_clk_src" [sound/soc/qcom/snd-soc-sdm845.ko]
undefined!
Add the corresponding select statement, as it is done in the other user
(Intel).
Fixes: f7485875a687 ("ASoC: sdm845: Add configuration for headset codec")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
From the da7219 spec, the button A, B, C and D are remapped to
0, 1, 2 and 3 respectively where button A is KEY_PLAYPAUSE,
B is KEY_VOLUMEUP, C is KEY_VOLUMEDOWN and D is KEY_VOICECOMMAND.
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Signed-off-by: Max Chang <changmax@chromium.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a quirk for the Point of View Mobii TAB-P1005W-232 v2.0 tablet, this
BYTCR device uses IN1 for its MIC and JD2 for jack-detect, rather then the
default IN3 and JD1.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a quirk for the Prowise PT301 tablet, this BYTCR tablet has no CHAN
package in its ACPI tables and uses SSP0-AIF1 rather then SSP0-AIF2 which
is the default for BYTCR devices.
Also it uses IN1 for its MIC and JD2 for jack-detect, rather then the
default IN3 and JD1.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASUS UX433FN and UX333FA with ALC294 cannot detect the headset MIC
and output through the internal speaker and the headphone until
ALC294_FIXUP_ASUS_SPK and ALC294_FIXUP_ASUS_HEADSET_MIC quirk applied.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ASUS UX533FD with ALC294 cannot detect the headset MIC and outputs
through the internal speaker and the headphone until
ALC294_FIXUP_ASUS_SPK and ALC294_FIXUP_ASUS_HEADSET_MIC quirk applied.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The known ALC256_FIXUP_ASUS_MIC fixup can fix the headphone jack
sensing and enable use of the internal microphone on this laptop
X542UN. However, it's ALC294 so create a new fixup named
ALC294_FIXUP_ASUS_MIC to avoid confusion.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make unified suspend / resume helpers and call them from both the
runtime- and the system-PM callbacks for simplifying code.
There are slight changes of call orders, but there shouldn't be any
functional difference after refactoring.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In an initial commit, 'SYNC_STATUS' register is referred to get
clock configuration, however this is wrong, according to my local
note at hand for reverse-engineering about packet dump. It should
be 'CLOCK_CONFIG' register. Actually, ff400_dump_clock_config()
is correctly programmed.
This commit fixes the bug.
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 76fdb3a9e1 ('ALSA: fireface: add support for Fireface 400')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Users reported a mute LED regression on Lenovo X1 Carbon, the root
cause is we applied the fixup of ALC285_FIXUP_LENOVO_HEADPHONE_NOISE
to this machine, then the machine can't apply the fixup of
ALC269_FIXUP_THINKPAD_ACPI anymore. To fix it, we chain two fixup
together.
Fixes: c4cfcf6f42 ("ALSA: hda/realtek - fix the pop noise on headphone for lenovo laptops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Driver rewritten, assign copyright notice and change module author
as original one remains silent and I want to be notified about bugs.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set DAI format and sysclk for headset codec.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set TDM time slots and DAI format for speaker codec.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sound capture and line bypass currently do not work as well as
some mixer controls. Fix that by building proper audio paths and
adjusting volume controls to match datasheet.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop "Common NI Values Table" and calculate LRCLK divider, then
add allowed rate constraints based on master clock frequency.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement set_bias_level to drive shutdown bit, so device is
put to sleep when unused.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch will enable headset button for new Chrome platform.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Extend some structs to add the support for jack button changes.
Now snd_hda_jack_add_kctl() receives two more arguments: the jack type
and the jack keymaps. Both are optional, and when zero are passed,
the function behaves just like before.
For reporting button state changes, you'd need to update
jack->button_state bits accordingly, typically in the jack callback.
Then the value OR'ed with button_state and the jack plug state is
passed to snd_jack_report().
Note that currently the code assumes only the one-shot button events,
i.e. it tries to send the button release soon after sending the button
event. If a driver really supports the button release handling by
itself, we may need to introduce some flag to control this behavior in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For allowing the callee to evaluate the associated jack information
and the unsolicited event data, add the new fields to
hda_jack_callback. They can be used, for example, to retrieve the
headset button state in the callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If it plugged headphone or headset into the jack, then
do the reboot, it will have a chance to cause headphone no sound.
It just need to run the headphone mode procedure after boot time.
The issue will be fixed.
It also suitable for ALC234 ALC274 and ALC294.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Realtek codec ALC3277 is 100% compatible with the codec RT5660
in I2S mode. And on the Dell IoT platform, the codec is ALC3277,
and the HID of the codec in the BIOS is 10EC3277, so adding this
ID to the ACPI match table.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Get the reset GPIO through the GPIO consumer API. This allows specifying the
DT property as "reset-gpios" without breaking existing DT users.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Get the reset GPIO through the GPIO consumer API. This allows specifying the
DT property as "reset-gpios" without breaking existing DT users.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
For the FSL ASoC card, the full node names appear to be "ssi", "esai",
and "sai", so there's not any reason to use strstr and of_node_name_eq
can be used instead.
Cc: Timur Tabi <timur@kernel.org>
Cc: Nicolin Chen <nicoleotsuka@gmail.com>
Cc: Xiubo Li <Xiubo.Lee@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
AMD platform device acp_audio_dma can only be created by parent PCI
device driver (drivers/gpu/drm/amd/amdgpu/amdgpu_acp.c). Pass struct
device of the parent to snd_pcm_lib_preallocate_pages() so
dma_alloc_coherent() can use correct dma_ops. Otherwise, it will
use default dma_ops which is nommu_dma_ops on x86_64 even when
IOMMU is enabled and set to non passthrough mode.
Though platform device inherits some dma related fields during its
creation in mfd_add_device(), we can't simply pass its struct device
to snd_pcm_lib_preallocate_pages() because dma_ops is not among the
inherited fields. Even it were, drivers/iommu/amd_iommu.c would
ignore it because get_device_id() doesn't handle platform device.
This change shouldn't give us any trouble even struct device of the
parent becomes null or represents some non PCI device in the future,
because get_dma_ops() correctly handles null struct device or uses
the default dma_ops if struct device doesn't have it set.
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We shouldn't assume CPU physical address we get from page_to_phys()
is same as DMA address we get from dma_alloc_coherent(). On x86_64,
we won't run into any problem with the assumption when dma_ops is
nommu_dma_ops. However, DMA address is IOVA when IOMMU is enabled.
And it's most likely different from CPU physical address when AMD
IOMMU is not in passthrough mode.
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Gnawty model Chromebook uses pmc_plt_clk_0 instead of pmc_plt_clk_3
for the mclk, just like the Clapper and Swanky models.
This commit adds a DMI based quirk for this.
This fixing audio no longer working on these devices after
commit 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
that commit fixes us unnecessary keeping unused clocks on, but in case of
the Gnawty that was breaking audio support since we were not using the
right clock in the cht_bsw_max98090_ti machine driver.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201787
Cc: stable@vger.kernel.org
Fixes: 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Reported-and-tested-by: Jaime Pérez <19.jaime.91@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
A couple of open coded iterating thru the child node names are converted
to use for_each_child_of_node() instead.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert soundbus uevent and sysfs OF node name and device type usage to
use printf specifier and helper functions instead of directly accessing
the name and type pointers. This will allow the eventual removal of the
pointers.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acer AIO Veriton Z4860G/Z6860G with the same ALC286 codec has issues
with the input from external microphone. The issue can be fixed by
the fixup ALC286_FIXUP_ACER_AIO_MIC_NO_PRESENCE for Veriton Z4660G.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acer AIO Veriton Z4660G with ALC286 codec has issue with the input
from external microphones connecting via 'Front Mic' jack. The fixup
ALC286_FIXUP_ACER_AIO_MIC_NO_PRESENCE enables the jack sensing of
the headset and fix the audio input issue of external microphone.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Acer AIO Aspire C24-860 with ALC286 can't detect the headset
microphone. Just like another Acer AIO U27-880, it needs a different
pin value for 0x18 and the headset fixup to make headset mic work.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acer Aspire U27-880(AIO) with ALC286 codec can not detect headset mic
and internal mic not working either. It needs the similar quirk like
Sony laptops to fix headphone jack sensing and enables use of the
internal microphone.
Unfortunately jack sensing for the headset mic is still not working.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch added max98373_reset function to avoid amp software reset failure and code duplication.
Reset verification step has been added for stable amp reset and it repeats verification maximum 3 times when it is failed.
Chip revision ID is available when the amp is in the idle state which means software reset is completed well.
Additional 10ms delay was added for every retrial and maximum 30ms delay can be applied.
Signed-off-by: Ryan Lee <ryans.lee@maximintegrated.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In DPCM case, it uses CPU-dummy / dummy-Codec dai links, and
non DPCM case, it uses CPU-Codec dai links.
Now, we want to merge audio-graph-card and audio-graph-scu-card.
These sound cards are using silimar but not same logic on each functions.
Then, of course we want to share same logic.
To compromise, this patch uses cpu/codec pointer on audio-graph-card.
It is same logic with audio-graph-scu-card, thus easy merging.
This is prepare for merging audio card
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current audio-graph-scu-card didn't care about codec_conf
for multi DPCM case. This patch cares it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In DPCM case, it uses CPU-dummy / dummy-Codec dai links, and
non DPCM case, it uses CPU-Codec dai links.
Now, we want to merge audio-graph-card and audio-graph-scu-card.
These sound cards are using silimar but not same logic on each functions.
Then, of course we want to share same logic.
To compromise, this patch uses cpu/codec pointer on audio-graph-scu-card.
It is same logic with audio-graph-card, thus easy merging.
This is prepare for merging audio card
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In DPCM case, it uses CPU-dummy / dummy-Codec dai links.
If sound card is caring only DPCM, link count = dai count,
but, if non DPCM case, link count != dai count.
Now, we want to merge audio-graph-card and audio-graph-scu-card,
then, we need to care both link / dai count more carefly
This patch cares it, and prepare for merging audio card
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
asoc_simple_card_get_dai_id() returns DAI ID, but it is based on
DT node's "endpoint" position.
Almost all cases 1 port has 1 endpoint, thus, it was no problem.
But in reality, port : endpoint = 1 : N, thus, counting endpoint
is BUG, it should based on "port" ID.
This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit c16015f36c ("ASoC: rsnd: add .get_id/.get_id_sub")
add new .get_id/.get_id_sub to indicate module ID/subID.
It is used for SSIU and CTU. In SSIU case, subID indicates BUSIF,
but register settings is based on SSIU ID.
OTOH, in CTU case, subID indicates CTU channel, and register settings
is based on it. This means regmap read/write function needs to care it.
This patch fixup this issue. It can't play MIXed sound without this
patch.
Fixes: c16015f36c ("ASoC: rsnd: add .get_id/.get_id_sub")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For TDM debug purpose, indicating Channel and Mode is very
useful. This patch indicate it if it has #define DEBUG
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tegra186 and Tegra194 contain the same codecs as earlier chips and can
be supported using the same patch function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recent devices support more than the 4 codecs that the AZX core will
probe by default. Probe up to 8 codecs to make sure all of them are
enumerated.
Suggested-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Clapper model Chromebook uses pmc_plt_clk_0 instead of pmc_plt_clk_3
for the mclk, just like the Swanky model.
This commit adds a DMI based quirk for this.
This fixing audio no longer working on these devices after
commit 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
that commit fixes us unnecessary keeping unused clocks on, but in case of
the Clapper that was breaking audio support since we were not using the
right clock in the cht_bsw_max98090_ti machine driver.
Cc: stable@vger.kernel.org
Fixes: 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These boards are now fully ported to devicetree and make use of the
simple-card driver, so the platform specific machine driver can be
removed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a USB sound card reports 0 interfaces, an error condition is triggered
and the function usb_audio_probe errors out. In the error path, there was a
use-after-free vulnerability where the memory object of the card was first
freed, followed by a decrement of the number of active chips. Moving the
decrement above the atomic_dec fixes the UAF.
[ The original problem was introduced in 3.1 kernel, while it was
developed in a different form. The Fixes tag below indicates the
original commit but it doesn't mean that the patch is applicable
cleanly. -- tiwai ]
Fixes: 362e4e49ab ("ALSA: usb-audio - clear chip->probing on error exit")
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Entry needed for ICL RVP w/ RT274
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We've got a regression report for some Thinkpad models (at least
T570s) which shows the too low speaker output volume. The bisection
leaded to the commit 61fcf8ece9 ("ALSA: hda/realtek - Enable Thinkpad
Dock device for ALC298 platform"), and it's basically adding the two
pin configurations for the dock, and looks harmless.
The real culprit seems, though, that the DAC assignment for the
speaker pin is implicitly assumed on these devices, i.e. pin NID 0x14
to be coupled with DAC NID 0x03. When more pins are configured by the
commit above, the auto-parser changes the DAC assignment, and this
resulted in the regression.
As a workaround, just provide the fixed pin / DAC mapping table for
this Thinkpad fixup function. It's no generic solution, but the
problem itself is pretty much device-specific, so must be good
enough.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1554304
Fixes: 61fcf8ece9 ("ALSA: hda/realtek - Enable Thinkpad Dock device for ALC298 platform")
Cc: <stable@vger.kernel.org>
Reported-and-tested-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a series of patches for conversion to LEDs audio-mute
trigger. It's based on 4.20-rc3 to be an immutable branch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add suffix ULL to constant 256 in order to give the compiler complete
information about the proper arithmetic to use.
Notice that such constant is used in a context that expects an
expression of type u64 (64 bits, unsigned) and the following
expression is currently being evaluated using 32-bit arithmetic:
256 * fs * 2 * mclk_src_scaling[i].param
Signed-off-by: Young_X <YangX92@hotmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jerome Brunet
Pierre-Louis Bossart
Takashi Iwai
Kirill Marinushkin
Maruthi Srinivas Bayyavarapu
Hui Wang
Mark Brown
Nathan Chancellor
Fabio Estevam
Ayman Bagabas
Gustavo A. R. Silva
Kuninori Morimoto
Takashi Sakamoto
Arnd Bergmann
Zhuohao Lee
Hans de Goede
Jian-Hong Pan
Chris Chiu
Ladislav Michl
Cheng-Yi Chiang
Kailang Yang
Daniel Mack
Rob Herring
Yu Zhao
Ryan Lee
Thierry Reding
Hui Peng
Young_X