* since ide_hwif_t.ide_dma_host_on is called either when drive->using_dma == 1
or when return value is discarded make it void, also drop "ide_" prefix
* make __ide_dma_host_on() void and drop "__" prefix
v2:
* while at it rename atiixp_ide_dma_host_on() to atiixp_dma_host_on()
and sgiioc4_ide_dma_host_on() to sgiioc4_dma_host_on().
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* since ide_hwif_t.ide_dma_{host_off,off_quietly} always return '0'
make these functions void and while at it drop "ide_" prefix
* fix comment for __ide_dma_off_quietly()
* make __ide_dma_{host_off,off_quietly,off}() void and drop "__" prefix
v2:
* while at it rename atiixp_ide_dma_host_off() to atiixp_dma_host_off(),
sgiioc4_ide_dma_{host_off,off_quietly}() to sgiioc4_dma_{host_off,off_quietly}()
and sl82c105_ide_dma_off_quietly() to sl82c105_dma_off_quietly()
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* add ide_set_dma() helper and make ide_hwif_t.ide_dma_check return
-1 when DMA needs to be disabled (== need to call ->ide_dma_off_quietly)
0 when DMA needs to be enabled (== need to call ->ide_dma_on)
1 when DMA setting shouldn't be changed
* fix IDE code to use ide_set_dma() instead if using ->ide_dma_check directly
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All users of ->mmio == 1 are gone so convert ->mmio into flag.
Noticed by Alan Cox.
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This results in smaller/faster/simpler code and allows future optimizations.
Also remove no longer needed ide[_mm]_{inl,outl}() and ide_hwif_t.{INL,OUTL}.
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* add ide_use_fast_pio() helper for use by host drivers
* add DMA capability and hwif->autodma checks to ide_use_dma()
- au1xxx-ide/it8213/it821x drivers didn't check for (id->capability & 1)
[ for the IT8211/2 in SMART mode this check shouldn't be made but since
in it821x_fixups() we set DMA bit explicitly:
if(strstr(id->model, "Integrated Technology Express")) {
/* In raid mode the ident block is slightly buggy
We need to set the bits so that the IDE layer knows
LBA28. LBA48 and DMA ar valid */
id->capability |= 3; /* LBA28, DMA */
we are better off using generic helper if we can ]
- ide-cris driver didn't set ->autodma
[ before the patch hwif->autodma was only checked in the chipset specific
hwif->ide_dma_check implementations, for ide-cris it is cris_dma_check()
function so there no behavior change here ]
v2:
* updated patch description (thanks to Alan Cox for the feedback)
v3:
* updated for scc_pata driver
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This field is no longer used by the core IDE code so fix ide-{disk,floppy}
drivers to keep openers count in the driver specific objects and remove
it from ide-{cd,scsi,tape} drivers (it was write-only).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
patch 2/2:
Remove clearing bmdma status from cdrom_decode_status() since ATA devices
might need it as well.
(http://lkml.org/lkml/2006/12/4/201 and http://lkml.org/lkml/2006/11/15/94)
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "Adam W. Hawks" <awhawks@us.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
patch 1/2 (revised):
- Fix drive->waiting_for_dma to work with CDB-intr devices.
- Do the dma status clearing in ide_intr() and add a new
hwif->ide_dma_clear_irq for Intel ICHx controllers.
Revised per Alan, Sergei and Bart's advice.
Patch against 2.6.20-rc6. Tested ok on my ICH4 and pdc20275 adapters.
Please review/apply, thanks.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "Adam W. Hawks" <awhawks@us.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
this is Joris' fixes reshuffelled and features renamed as David requested.
- acm_set_control is not mandatory, honour that
- throtteling is reset upon open
- throtteling is read consistently when processing input data
Signed-off-by: Joris van Rantwijk <jorispubl@xs4all.nl>
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The status in usb_iso_packet_descriptor should be signed, for the benefit
of someone who casts to a long or makes other benign misstep (the principle
of least surprise).
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use __u32 rather than u32 in userspace ioctl defines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
there's a USB mass storage device which exists in two version. One
reports the correct size and the other does not. Apart from that they
are identical and cannot be told apart. Here's a heuristic based on the
empirical finding that drives have even sizes.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb: descriptor structures have to be packed
Many of the Wireless USB decriptors added to usb_ch9.h don't have the
__attribute__((packed)) tag, and thus, they don't reflect the wire
size. This patch fixes that.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I added two fields to struct usb_serial_port to keep track of the
throttle state. Other usb-serial drivers typically use private data for
such things, but the generic driver can not really do that because some
of its code is also used by other drivers (which may have their own
private data needs).
As it is, I am not sure that this patch is useful in all scenarios.
It is certainly helpful for low-bandwidth devices that can hold their
data in response to throttling. But for devices that pump data in
real-time as fast as possible (webcam, A/D converter, etc), throttling
may actually cause more data loss.
From: Joris van Rantwijk <jorispubl@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CARDBUS_MEM_SIZE was increased to 64MB on 2.6.20-rc2, but larger size might
result in allocation failure for the reserving itself on some platforms
(for example typical 32bit MIPS). Make it (and CARDBUS_IO_SIZE too)
customizable by "pci=" option for such platforms.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add function of_get_mac_address(), which obtains the best MAC address to use
from the device tree by checking various properties in order. The order is:
'mac-address', then 'local-mac-address', then 'address'. It skips properties
that contain invalid MAC addresses, which were probably not initialized
by U-Boot.
Update gfar_of_init() and fs_enet_of_init() in fsl_soc.c to call
of_get_mac_address().
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
debugfs: implement symbolic links
Implement a new function debugfs_create_symlink() which can be used
to create symbolic links in debugfs. This function can be useful
for people moving functionality from /proc to debugfs (e.g. the
gcov-kernel patch).
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On recent systems, calls to /sbin/modprobe are handled by udev depending
on the kind of device the kernel has discovered. This patch creates an
uevent for the kernels internal request_module(), to let udev take control
over the request, instead of forking the binary directly by the kernel.
The direct execution of /sbin/modprobe can be disabled by setting:
/sys/module/kmod/mod_request_helper (/proc/sys/kernel/modprobe)
to an empty string, the same way /proc/sys/kernel/hotplug is disabled on an
udev system.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Extend rdma_cm to support multicast communication. Multicast support
is added to the existing RDMA_PS_UDP port space, as well as a new
RDMA_PS_IPOIB port space. The latter port space allows joining the
multicast groups used by IPoIB, which enables offloading IPoIB traffic
to a separate QP. The port space determines the signature used in the
MGID when joining the group. The newly added RDMA_PS_IPOIB also
allows for unicast operations, similar to RDMA_PS_UDP.
Supporting the RDMA_PS_IPOIB requires changing how UD QPs are initialized,
since we can no longer assume that the qkey is constant. This requires
saving the Q_Key to use when attaching to a device, so that it is
available when creating the QP. The Q_Key information is exported to
the user through the existing rdma_init_qp_attr() interface.
Multicast support is also exported to userspace through the rdma_ucm.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IB SA tracks multicast join/leave requests on a per port basis and
does not do any reference counting: if two users of the same port join
the same group, and one leaves that group, then the SA will remove the
port from the group even though there is one user who wants to stay a
member left. Therefore, in order to support multiple users of the
same multicast group from the same port, we need to perform reference
counting locally.
To do this, add an multicast submodule to ib_sa to perform reference
counting of multicast join/leave operations. Modify ib_ipoib (the
only in-kernel user of multicast) to use the new interface.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
_GTF is an acpi method that is used to reinitialize the drive. It returns
a task file containing ata commands that are sent back to the drive to restore
it to boot up defaults.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
(cherry picked from 9c69cab24b51a89664f4c0dfaf8a436d32117624 commit)
* 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32:
[AVR32] Use per-controller spi_board_info structures
[AVR32] Warn, don't BUG if clk_disable is called too many times
[AVR32] Make sure all genclocks have a parent
[AVR32] Remove unnecessary sys_nfsservctl conditional
[AVR32] Wire up the SysV IPC calls properly
[AVR32] Define ioremap_nocache, ioport_map and ioport_unmap
[AVR32] Fix prototypes for __raw_writesb and friends
scsi_transport.h defines the inline function scsi_transport_device_data() that
dereferences a pointer of "struct scsi_device *". Since the struct is not
known by the header this might break compilation.
Include scsi/scsi_device.h to not rely on users doing the correct magic
include order.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Simplify the memory management and code a bit by representing acls with an
array instead of a linked list.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that disable_irq() defaults to delayed-disable semantics, the IRQ_DISABLED
flag is not needed anymore.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts x86_64 to use the GENERIC_TIME infrastructure and adds
clocksource structures for both TSC and HPET (ACPI PM is shared w/ i386).
[akpm@osdl.org: fix printk timestamps]
[akpm@osdl.org: fix printk ckeanups]
[akpm@osdl.org: hpet build fix]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In preparation for the x86_64 generic time conversion, this patch splits out
TSC and HPET related code from arch/x86_64/kernel/time.c into respective
hpet.c and tsc.c files.
[akpm@osdl.org: fix printk timestamps]
[akpm@osdl.org: cleanup]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In preparation for supporting generic timekeeping, this patch cleans up
x86-64's use of vxtime.hpet_address, changing it to just hpet_address as is
also used in i386. This is necessary since the vxtime structure will be going
away.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add SysRq-Q to print pending timers and other timer info.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement high resolution timers on top of the hrtimers infrastructure and the
clockevents / tick-management framework. This provides accurate timers for
all hrtimer subsystem users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The local apic timer calibration has two problem cases:
1. The calibration is based on readout of the PIT/HPET timer to detect the
wrap of the periodic tick. It happens that a box gets stuck in the
calibration loop due to a PIT with a broken readout function.
2. CoreDuo boxen show a sporadic PIT runs too slow defect, which results
in a wrong lapic calibration. The PIT goes back to normal operation once
the lapic timer is switched to periodic mode.
Both are existing and unfixed problems in the current upstream kernel and
prevent certain laptops and other systems from booting Linux.
Rework the code to address both problems:
- Make the calibration interrupt driven. This removes the wait_timer_tick
magic hackery from lapic.c and time_hpet.c. The clockevents framework
allows easy substitution of the global tick event handler for the
calibration. This is more accurate than monitoring jiffies. At this point
of the boot process, nothing disturbes the interrupt delivery, so the
results are very accurate.
- Verify the calibration against the PM timer, when available by using the
early access function. When the measured calibration period is outside of
an one percent window, then the lapic timer calibration is adjusted to the
pm timer result.
- Verify the calibration by running the lapic timer with the calibration
handler. Disable lapic timer in case of deviation.
This also removes the "synchronization" of the local apic timer to the global
tick. This synchronization never worked, as there is no way to synchronize
PIT(HPET) and local APIC timer. The synchronization by waiting for the tick
just alignes the local APIC timer for the first events, but later the events
drift away due to the different clocks. Removing the "sync" is just
randomizing the asynchronous behaviour at setup time.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Zachary Amsden <zach@vmware.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rohit Seth <rohitseth@google.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add clockevent drivers for i386: lapic (local) and PIT/HPET (global). Update
the timer IRQ to call into the PIT/HPET driver's event handler and the
lapic-timer IRQ to call into the lapic clockevent driver. The assignement of
timer functionality is delegated to the core framework code and replaces the
compile and runtime evalution in do_timer_interrupt_hook()
Use the clockevents broadcast support and implement the lapic_broadcast
function for ACPI.
No changes to existing functionality.
[ kdump fix from Vivek Goyal <vgoyal@in.ibm.com> ]
[ fixes based on review feedback from Arjan van de Ven <arjan@infradead.org> ]
Cleanups-from: Adrian Bunk <bunk@stusta.de>
Build-fixes-from: Andrew Morton <akpm@osdl.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With Ingo Molnar <mingo@elte.hu>
Add functions to provide dynamic ticks and high resolution timers. The code
which keeps track of jiffies and handles the long idle periods is shared
between tick based and high resolution timer based dynticks. The dyntick
functionality can be disabled on the kernel commandline. Provide also the
infrastructure to support high resolution timers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With Ingo Molnar <mingo@elte.hu>
The tick-management code is the first user of the clockevents layer. It takes
clock event devices from the clock events core and uses them to provide the
periodic tick.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Architectures register their clock event devices, in the clock events core.
Users of the clockevents core can get clock event devices for their use. The
clockevents core code provides notification mechanisms for various clock
related management events.
This allows to control the clock event devices without the architectures
having to worry about the details of function assignment. This is also a
preliminary for high resolution timers and dynamic ticks to allow the core
code to control the clock functionality without intrusive changes to the
architecture code.
[Fixes-by: Ingo Molnar <mingo@elte.hu>]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The apic code is quite unstructured and missing a lot of comments.
- Restructure the code into helper functions, timer, setup/shutdown,
interrupt and power management blocks.
- Fixup comments.
- Namespace fixups
- Inline helpers for version and is_integrated
- Combine the ack_bad_irq functions
No functional changes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Zachary Amsden <zach@vmware.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rohit Seth <rohitseth@google.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow early access to the power management timer by exposing the verified read
function and providing a helper function which checks the pmtmr_ioport
variable and returns either the pm timer readout or 0 in case the pm timer is
not available.
Create a new header file and replace also the ifdef'ed extern definition in
arch/i386/kernel/acpi/boot.c
This is a preperatory patch for the rework of the local apic timer
calibration.
No functional changes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a preperatory patch for highres/dyntick:
- replace the big #ifdef ARCH_APICTIMER_STOPS_ON_C3 hackery by functions
- remove the double switch in the power verify function (in the worst case
we switched ipi to apic and 20usec later apic to ipi)
- keep track of the the state which stops local APIC timer
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Len Brown <len.brown@intel.com>
Cc: <linux-acpi@vger.kernel.org>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reintroduce ktimers feature "optimized away" by the ktimers review process:
remove the curr_timer pointer from the cpu-base and use the hrtimer state.
No functional changes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reintroduce ktimers feature "optimized away" by the ktimers review process:
multiple hrtimer states to enable the running of hrtimers without holding the
cpu-base-lock.
(The "optimized" rbtree hack carried only 2 states worth of information and we
need 4 for high resolution timers and dynamic ticks.)
No functional changes.
Build-fixes-from: Andrew Morton <akpm@osdl.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Improve kernel/hrtimers.c locking: use a per-CPU base with a lock to control
locking of all clocks belonging to a CPU. This simplifies code that needs to
lock all clocks at once. This makes life easier for high-res timers and
dyntick.
No functional changes.
[ optimization change from Andrew Morton <akpm@osdl.org> ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- hrtimers did not use the hrtimer_restart enum and relied on the implict
int representation. Fix the prototypes and the functions using the enums.
- Use seperate name spaces for the enumerations
- Convert hrtimer_restart macro to inline function
- Add comments
No functional changes.
[akpm@osdl.org: fix input driver]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For CONFIG_NO_HZ we need to calculate the next timer wheel event based on a
given jiffie value. Extend the existing code to allow the extra 'now'
argument. Provide a compability function for the existing implementations to
call the function with now == jiffies. (This also solves the racyness of the
original code vs. jiffies changing during the iteration.)
No functional changes to existing users of this infrastructure.
[ remove WARN_ON() that triggered on s390, by Carsten Otte <cotte@de.ibm.com> ]
[ made new helper static, Adrian Bunk <bunk@stusta.de> ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Uninline irq_enter(). [dynticks adds more stuff to it]
No functional changes.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Geode can safely use the TSC for highres, since:
1) Does not support frequency scaling,
2) The TSC _does_ count when the CPU is halted. Furthermore, the Geode
supports a mode called "suspension on halt", where Suspend mode (which
interacts with the power management states) is entered. TSC counting
during suspend mode is controlled by bit 8 of the Bus Controller
Configuration Register #0 (thanks Tom!).
3) no SMP :)
Check if "RTSC counts during suspension" and remove the requirement for
verification, so the clocksource code can safely select it as an timesource
for the highres timers subsystem.
Signed-off-by: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The TSC needs to be verified against another clocksource. Instead of using
hardwired assumptions of available hardware, provide a generic verification
mechanism. The verification uses the best available clocksource and handles
the usability for high resolution timers / dynticks of the clocksource which
needs to be verified.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The clocksource code allows direct updates of the rating of a given
clocksource now. Change TSC unstable tracking to use this interface and
remove the update callback.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using a flag filed allows to encode more than one information into a variable.
Preparatory patch for the generic clocksource verification.
[mingo@elte.hu: convert vmitime.c to the new clocksource flag]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
make the TSC synchronization code more robust, and unify it between x86_64 and
i386.
The biggest change is the removal of the 'fix up TSCs' code on x86_64 and
i386, in some rare cases it was /causing/ time-warps on SMP systems.
The new code only checks for TSC asynchronity - and if it can prove a
time-warp (if it can observe the TSC going backwards when going from one CPU
to another within a critical section), then the TSC clock-source is turned
off.
The TSC synchronization-checking code also got moved into a separate file.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enqueue clocksources in rating order to make selection of the clocksource
easier. Also check the match with an user override at enqueue time.
Preparatory patch for the generic clocksource verification.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Prevent timeout overflow if timer ticks are behind jiffies (due to high
softirq load or due to dyntick), by limiting the valid timeout range to
MAX_LONG/2.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are loads of fat functions hidden in jiffies.h. Uninline them. No code
changes.
[jeremy@goop.org: export fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Distangle the NTP update from HZ. This is necessary for dynamic tick enabled
kernels.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide funtions to:
- check, whether an interrupt can set the affinity
- pin the interrupt to a given cpu
Necessary for the ability to setup clocksources more flexible (e.g. use the
different HPET channels per CPU)
[akpm@osdl.org: alpha build fix]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a flag so we can prevent the irq balancing of an interrupt. Move the
bits, so we have room for more :)
Necessary for the ability to setup clocksources more flexible (e.g. use the
different HPET channels per CPU)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patches fixes two bugs in the scsi target infrastructure's
user/kernel interface.
- It wrongly assumes that the ring buffer size of the interface (64KB)
is larger than or equal to the system page size. This patch sets the
ring buffer size to PAGE_SIZE if the system page size is larger.
- It uses PAGE_SIZE in the header file exported to userspace. This
patch removes it.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add kexec support to ARM.
Improvements like commandline handling could be made but this patch gives
basic functional support. It uses the next available syscall number, 347.
Once the syscall number is known, userspace support will be
finalised/submitted to kexec-tools, various patches already exist.
Originally based on a patch by Maxim Syrchin but updated and forward
ported by various people.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Remove a duplicated define for AT91_RSTC_KEY
- Set AT91_RSTC_KEY to the correct value
- Replace the hardcoded keys in at91sam9620.c and at91sam9261.c
by AT91_RSTC_KEY
Signed-off-by: Jan Altenberg <jan@linutronix.de>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Set up one spi_board_info array per controller and pass this to
at32_add_device_spi so that it can set up any GPIO pins for chip
selects based on this information.
Extracted from a patch by David Brownell and adapted slightly.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The macro "get_irqnr_and_base" in "entry-macro.S" optimized
according to Lennert Buytenhek suggestion.
Comments from Pavel Pisa:
Sascha has approved patch some days ago
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Wire up the individual sysvipc system calls and remove sys_ipc.
Strictly speaking, this breaks the ABI, but since sys_ipc never
worked anyway due to a silly bug, it isn't actually a regression.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
These are all defined in terms of ioremap/iounmap since port I/O
isn't really different from memory-mapped I/O on AVR32.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The first parameter to __raw_writes[bwl] and __raw_reads[bwl] should
be a void __iomem *, not unsigned long.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Hook in a cpu specific reset function for the S3C2443
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add hook code to specify cpu specific reset call
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add arch/arm/mach-s3c2443 for support of the Samsung S3C2443 SoC
This patch adds the core CPU support, clock framework, times
and initial IRQ support, as well as adding the directory into
the build tree.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Getting BenH's new EMAC driver working on 440GP, I found some more
problems in the native mode paths of the new DCR code:
- dcr_map() is supposed to return a dcr_host_t, but the native
version is a macro that doesn't expand to an expression. With native
DCRs, dcr_host_t is an empty structure, so we just use a constructor
expression instead.
- dcr_unmap() uses {} instead of the safer do {} while (0)
idiom to implement a no-op
Here's a fix.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds driver code for the PMI device found in future IBM products.
PMI stands for "Platform Management Interrupt" and is a way to
communicate with the BMC (Baseboard Management Controller).
It provides bidirectional communication with a low latency.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Heiko J Schick <schickhj@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add PS3 system manager support and the ppc_md routines restart() and
power_off().
The system manager provides an event notification mechanism for reporting
events like thermal alert and button presses. It also provides support to
control system shutdown and startup.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanups for the PS3 vuart driver.
- Hide driver private data from external interface with new structure
ps3_vuart_port_priv.
- Fix masking bug in ps3_vuart_get_interrupt_status().
- Add new helper routine ps3_vuart_clear_rx_bytes() to flush rx buffer.
- Add new variable probe_mutex to serialize probe and destroy routines.
- Rename some symbols.
- Add platform check in ps3_vuart_bus_init().
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If an ATA drive uses legacy mode, ata driver will choose 14 and 15
as the fixed irq number. On ia64 platform, such numbers are GSI and
should be converted to irq vector.
Below patch against kernel 2.6.20 fixes it.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is the first preparation to doing the !IORDY cases properly. Further
diffs will then add the needed logic to do it right.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 80c wire bit is bit 13, not 14. Bit 14 is always 1 if word93 is
implemented. This increases the chance of incorrect wire detection
especially because host side cable detection is often unreliable and
we sometimes soley depend on drive side cable detection. Fix the test
and add word93 validity check.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ACPI AML supports "serialized" methods which are protected
by an implicit mutex. The mutex is re-entrant for that AML thread
to allow recursion.
However, Linux implements notify() by creating a new AML thread.
So for systems where notify() re-enters a serialized method,
deadlock results.
The fix is to use the Linux thread_id as the key to allowing
re-entrancy, not the AML thread pointer.
http://bugzilla.kernel.org/show_bug.cgi?id=5534
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add support for the Atmel AT91SAM9XE range of processors. These are
basically AT91SAM9260's with different amounts of internal SRAM and
Flash.
We make use of the existing AT91SAM9260 support, but just perform
run-time detection of the size of the internal SRAM.
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a define of S3C2410_IRQSUB() to define all
the sources from the IRQSUB register, to make it
easier to work out the datasheet=>irq mappings
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch enables the L220 on the RealView/EB MPCore platform.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The kernel originally supported revB only. This patch enables revC by
default and adds a config option for building the kernel for the revB
platform. Since the SCU base address was hard-coded in the proc-v6.S
file (and only valid for RealView/EB revB), this patch also adds a
more generic support for defining the SCU information.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MPCore platform
This patch adds the registration of the secondary GIC on the
baseboard, together with the IRQ chaining setup.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current implementation only assumes one GIC to be present in the
system. However, there are platforms with more than one cascaded interrupt
controllers (RealView/EB MPCore for example).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This tidies up some of the rts7751r2d mess and gets it booting
again. Update the defconfig, too.
Signed-off-by: Masayuki Hosokawa <hosokawa@ace-jp.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
I just noticed the comments about even/odd ioctl command numbers in
Linux's wireless.h file are mixed up.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It isn't needed anymore, all of the users are gone, and all of the ctl_table
initializers have been converted to use explicit names of the fields they are
initializing.
[akpm@osdl.org: NTFS fix]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a parent entry into the ctl_table so you can walk the list of parents and
find the entire path to a ctl_table entry.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With this change the sysctl inodes can be cached and nothing needs to be done
when removing a sysctl table.
For a cost of 2K code we will save about 4K of static tables (when we remove
de from ctl_table) and 70K in proc_dir_entries that we will not allocate, or
about half that on a 32bit arch.
The speed feels about the same, even though we can now cache the sysctl
dentries :(
We get the core advantage that we don't need to have a 1 to 1 mapping between
ctl table entries and proc files. Making it possible to have /proc/sys vary
depending on the namespace you are in. The currently merged namespaces don't
have an issue here but the network namespace under /proc/sys/net needs to have
different directories depending on which network adapters are visible. By
simply being a cache different directories being visible depending on who you
are is trivial to implement.
[akpm@osdl.org: fix uninitialised var]
[akpm@osdl.org: fix ARM build]
[bunk@stusta.de: make things static]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current logic to walk through the list of sysctl table headers is slightly
painful and implement in a way it cannot be used by code outside sysctl.c
I am in the process of implementing a version of the sysctl proc support that
instead of using the proc generic non-caching monster, just uses the existing
sysctl data structure as backing store for building the dcache entries and for
doing directory reads. To use the existing data structures however I need a
way to get at them.
[akpm@osdl.org: warning fix]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The semantic effect of insert_at_head is that it would allow new registered
sysctl entries to override existing sysctl entries of the same name. Which is
pain for caching and the proc interface never implemented.
I have done an audit and discovered that none of the current users of
register_sysctl care as (excpet for directories) they do not register
duplicate sysctl entries.
So this patch simply removes the support for overriding existing entries in
the sys_sysctl interface since no one uses it or cares and it makes future
enhancments harder.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Corey Minyard <minyard@acm.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are currently no users in the kernel for CTL_ANY and it only has effect
on the binary interface which is practically unused.
So this complicates sysctl lookups for no good reason so just remove it.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ocfs2 was did not have the binary number it uses under CTL_FS registered in
sysctl.h. Register it to avoid future conflicts, and change the name of the
definition to be in line with the rest of the sysctl numbers.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to have the the definition of all top level sysctl directories
registers in sysctl.h so we don't conflict by accident and cause abi problems.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for using a filesystem UUID to identify and export point in the
filehandle.
For NFSv2, this UUID is xor-ed down to 4 or 8 bytes so that it doesn't take up
too much room. For NFSv3+, we use the full 16 bytes, and possibly also a
64bit inode number for exports beneath the root of a filesystem.
When generating an fsid to return in 'stat' information, use the UUID (hashed
down to size) if it is available and a small 'fsid' was not specifically
provided.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On ia64, drivers/base/dma-mapping.c doesn't build because it calls
dma_alloc_noncoherent() and dma_free_noncoherent(), which appear to be
terminally broken; the calls end up generating errors like
drivers/base/dma-mapping.c: In function 'dmam_noncoherent_release':
drivers/base/dma-mapping.c:32: error: 'struct ia64_machine_vector' has no member named 'platform_dma_free_coherent'
because the multiple levels of macro expansion in <asm/dma-mapping.h> and
<asm/machvec.h> end up turning a call to dma_free_noncoherent() into
ia64_mv.platform_dma_free_coherent (instead of the intended
ia64_mv.dma_free_coherent).
This patch fixes this by converting dma_{alloc,free}_noncoherent() into
inline functions that call the corresponding coherent functions, instead of
trying to do this with macros.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable svc access to cp6 via an undefined instruction hook. Do not enable
access for usr code.
This patch also makes iop13xx select PLAT_IOP, this requires a small change
to drivers/i2c/busses/i2c-iop3xx.c.
Per Lennert Buytenhek's note, the cp6 trap routine is moved to arch/arm/plat-iop
Per Nicolas Pitre's note, the cp_wait is skipped since the latency to
return to the faulting function is longer than cp_wait.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implement a custom ioremap implementation for iop3xx. This saves
establishing new mappings. It also cleans up the PCI IO resource to be a
physical address rather than a virtual address as Russell pointed out on
the original iop13xx port.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the CPU code, and any board specific initialisation
code to change the allocation order of the DMA channels,
or stop a peripheral allocating any DMA at-all.
This is due to the scarce mapping of DMA channels on
some earlier S3C24XX cpus, where the selection changes
depending on the channel in use.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is adding the functions and structures used for handling the
S3C24XX udc driver platform datas.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Neither of these have had any maintenance in years, and there's
no interest in keeping them straggling along. These have already
been slated for removal some time, so finally just get rid of them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This ended up causing problems for older parts (particularly ones
using PTEA). Revert this for now, it can be added back in once it's
had some more testing.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPSEC]: Fix the address family to refer encap_family
[IPSEC]: changing API of xfrm6_tunnel_register
[IPSEC]: make sit use the xfrm4_tunnel_register
[IPSEC]: Changing API of xfrm4_tunnel_register.
[TCP]: Prevent pseudo garbage in SYN's advertized window
[NET_SCHED]: sch_hfsc: replace ASSERT macro by WARN_ON
[BRIDGE] br_if: Fix oops in port_carrier_check
[NETFILTER]: Clear GSO bits for TCP reset packet
[TG3]: Update copyright, version, and reldate.
[TG3]: Add some tx timeout debug messages.
[TG3]: Use constant for PHY register 0x1e.
[TG3]: Power down 5704 serdes transceiver when shutting down.
[TG3]: 5906 doesn't need to switch to slower clock.
[TG3]: 5722/5756 don't need PHY jitter workaround.
[TG3]: Use lower DMA watermark for 5703.
[TG3]: Save MSI state before suspend.
[XFRM]: Fix IPv4 tunnel mode decapsulation with IPV6=n
[IPV6] HASHTABLES: Use appropriate seed for caluculating ehash index.
udbg_early_init() is a function used on 64 bit systems, which
initializes whichever early udbg backend is configured. This function
is not called on 32-bit, however if btext early debug is enabled it
does have an explicit, inline, #ifdef-ed assignment performing
analagous initialization.
This patch makes things more uniform by folding the btext
initialization as an option into udbg_early_init() and calling that
from the 32-bit setup path.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Stop using i2c_adapter.class_dev
i2c: Remove the warning on missing adapter device
i2c: Declare more i2c_adapter parent devices
i2c: PA Semi SMBus driver
i2c-amd8111: Proposed cleanups
i2c-parport: Add support for One For All remote JP1 interface
i2c-viapro: Add support for the VIA CX700 south bridge
i2c: Add IDs to adapters
i2c: Update the list of bus IDs
i2c: Add driver suspend/resume/shutdown support
i2c: completion header cleanups
i2c-i801: Document the SMBus unhiding quirk
i2c-i801: Spelling fix
i2c: Fix typo in SMBus Write Word Data description
i2c-piix4: Add support for the ATI SB600
i2c-nforce2: Drop unused reference to pci_dev
i2c/vt8231: Remove superfluous initialization
i2c-ali1563: Fix device initialization
i2c-ali1563: Improve the status messages
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix sigset_t endianess swapping issues in 32-bit compat code.
[MIPS] Fix uniprocessor Sibyte builds.
[MIPS] Make entry.S a little more readable.
[MIPS] Remove stray instruction from __get_user_asm_ll32.
[MIPS] 32-bit: Fix warning about cast for fetching pointer from userspace.
[MIPS] DECstation: Fix irq handling
[MIPS] signals: make common _BLOCKABLE macro
[MIPS] signal: Move sigframe definition for native O32/N64 into signal.c
[MIPS] signal: Move {restore,setup}_sigcontext prototypes to their user
[MIPS] signal: Fix warnings in o32 compat code.
[MIPS] IP27: Enable N32 support in defconfig.
Revert "[MIPS] Fix warning in get_user when fetching pointer object from userspace."
[MIPS] Don't claim we support dma_declare_coherent_memory - we don't.
[MIPS] Unify dma-{coherent,noncoherent.ip27,ip32}
[MIPS] Improve branch prediction in ll/sc atomic operations.
This did result in double clearing of the error return value on success
only but should make a meassurable overhead for sigreturn.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Platforms will now have to supply a function dma_device_is_coherent which
returns if a particular device participates in the coherence domain. For
most platforms this function will always return 0 or 1.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that finally all supported versions of binutils have functioning
support for .subsection use .subsection to tweak the branch prediction
I did not modify the R10000 errata variants because it seems unclear if
this will invalidate the workaround which actually relies on the cheesy
prediction of branch likely to cause a misspredict if the sc was
successful.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IDs have been defined but not used by most of the I2C adapters.
By having a unique ID, clients can check for correct connection
during probe.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* The Voodoo3 has no SMBus, it has two bit-banged busses which
already have an ID assigned (I2C_HW_B_VOO).
* The i2c-ipmi bus driver was a non-sense, it'll never be ported
to Linux 2.6.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Yani Ioannou <yani.ioannou@gmail.com>
Driver model updates for the I2C core:
- Add new suspend(), resume(), and shutdown() methods. Use them in the
standard driver model style; document them.
- Minor doc updates to highlight zero-initialized fields in drivers, and
the driver model accessors for "clientdata".
If any i2c drivers were previously using the old suspend/resume calls
in "struct driver", they were getting warning messages ... and will
now no longer work. Other than that, this patch changes no behaviors;
and it lets I2C drivers use conventional PM and shutdown support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is a clean up patch that includes the following changes:
-Some comments were added to clarify the code based on feedback
from the community.
-The write_pm_cntrl() and set_count_mode() were passed a
structure element from a global variable. The argument was
removed so the functions now just operate on the global directly.
-The set_pm_event() function call in the cell_virtual_cntr()
routine was moved to a for-loop before the for_each_cpu loop
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch changes xfrm6_tunnel register and deregister
interface to prepare for solving the conflict of device
tunnels with inter address family IPsec tunnel.
There is no device which conflicts with IPv4 over IPv6
IPsec tunnel.
Signed-off-by: Kazunori MIYAZAWA <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't make any sense to have a priority field in the physical spu
structure. Move it into the spu context instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch changes xfrm4_tunnel register and deregister
interface to prepare for solving the conflict of device
tunnels with inter address family IPsec tunnel.
Signed-off-by: Kazunori MIYAZAWA <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extern declarations belong in headers. Times, they are a'changin.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
===================================================================
When I implemented the DECLARE_PER_CPU(var) macros, I was careful that
people couldn't use "var" in a non-percpu context, by prepending
percpu__. I never considered that this would allow them to overload
the same name for a per-cpu and a non-percpu variable.
It is only one of many horrors in the i386 boot code, but let's rename
the non-perpcu cpu_gdt_descr to early_gdt_descr (not boot_gdt_descr,
that's something else...)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
===================================================================
On the Unisys ES7000/ONE system, we encountered a problem where performing
a kexec reboot or dump on any cell other than cell 0 causes the system
timer to stop working, resulting in a hang during timer calibration in the
new kernel.
We traced the problem to one line of code in disable_IO_APIC(), which needs
to restore the timer's IO-APIC configuration before rebooting. The code is
currently using the 4-bit physical destination field, rather than using the
8-bit logical destination field, and it cuts off the upper 4 bits of the
timer's APIC ID. If we change this to use the logical destination field,
the timer works and we can kexec on the upper cells. This was tested on
two different cells (0 and 2) in an ES7000/ONE system.
For reference, the relevant Intel xAPIC spec is kept at
ftp://download.intel.com/design/chipsets/e8501/datashts/30962001.pdf,
specifically on page 334.
Signed-off-by: Benjamin M Romer <benjamin.romer@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
During kernel bootup, a new T60 laptop (CoreDuo, 32-bit) hangs about
10%-20% of the time in acpi_init():
Calling initcall 0xc055ce1a: topology_init+0x0/0x2f()
Calling initcall 0xc055d75e: mtrr_init_finialize+0x0/0x2c()
Calling initcall 0xc05664f3: param_sysfs_init+0x0/0x175()
Calling initcall 0xc014cb65: pm_sysrq_init+0x0/0x17()
Calling initcall 0xc0569f99: init_bio+0x0/0xf4()
Calling initcall 0xc056b865: genhd_device_init+0x0/0x50()
Calling initcall 0xc056c4bd: fbmem_init+0x0/0x87()
Calling initcall 0xc056dd74: acpi_init+0x0/0x1ee()
It's a hard hang that not even an NMI could punch through! Frustratingly,
adding printks or function tracing to the ACPI code made the hangs go away
...
After some time an additional detail emerged: disabling the NMI watchdog
made these occasional hangs go away.
So i spent the better part of today trying to debug this and trying out
various theories when i finally found the likely reason for the hang: if
acpi_ns_initialize_devices() executes an _INI AML method and an NMI
happens to hit that AML execution in the wrong moment, the machine would
hang. (my theory is that this must be some sort of chipset setup method
doing stores to chipset mmio registers?)
Unfortunately given the characteristics of the hang it was sheer
impossible to figure out which of the numerous AML methods is impacted
by this problem.
As a workaround i wrote an interface to disable chipset-based NMIs while
executing _INI sections - and indeed this fixed the hang. I did a
boot-loop of 100 separate reboots and none hung - while without the patch
it would hang every 5-10 attempts. Out of caution i did not touch the
nmi_watchdog=2 case (it's not related to the chipset anyway and didnt
hang).
I implemented this for both x86_64 and i686, tested the i686 laptop both
with nmi_watchdog=1 [which triggered the hangs] and nmi_watchdog=2, and
tested an Athlon64 box with the 64-bit kernel as well. Everything builds
and works with the patch applied.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Old code was legal standard C, but apparently not sparse-C.
Signed-off-by: Josef 'Jeff' Sipek <jsipek@cs.sunysb.edu>
Signed-off-by: Andi Kleen <ak@suse.de>
When a machine check event is detected (including a AMD RevF threshold
overflow event) allow to run a "trigger" program. This allows user space
to react to such events sooner.
The trigger is configured using a new trigger entry in the
machinecheck sysfs interface. It is currently shared between
all CPUs.
I also fixed the AMD threshold handler to run the machine
check polling code immediately to actually log any events
that might have caused the threshold interrupt.
Also added some documentation for the mce sysfs interface.
Signed-off-by: Andi Kleen <ak@suse.de>
Unlike x86, x86_64 already passes arguments in registers. The use of
regparm attribute makes no difference in produced code, and the use of
fastcall just bloats the code.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This patch resolves the issue of running with numa=fake=X on kernel command
line on x86_64 machines that have big IO hole. While calculating the size
of each node now we look at the total hole size in that range.
Previously there were nodes that only had IO holes in them causing kernel
boot problems. We now use the NODE_MIN_SIZE (64MB) as the minimum size of
memory that any node must have. We reduce the number of allocated nodes if
the number of nodes specified on kernel command line results in any node
getting memory smaller than NODE_MIN_SIZE.
This change allows the extra memory to be incremented in NODE_MIN_SIZE
granule and uniformly distribute among as many nodes (called big nodes) as
possible.
[akpm@osdl.org: build fix]
Signed-off-by: David Rientjes <reintjes@google.com>
Signed-off-by: Paul Menage <menage@google.com>
Signed-off-by: Rohit Seth <rohitseth@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Clean up sched_clock() on i686: it will use the TSC if available and falls
back to jiffies only if the user asked for it to be disabled via notsc or
the CPU calibration code didnt figure out the right cpu_khz.
This generally makes the scheduler timestamps more finegrained, on all
hardware. (the current scheduler is pretty resistant against asynchronous
sched_clock() values on different CPUs, it will allow at most up to a jiffy
of jitter.)
Also simplify sched_clock()'s check for TSC availability: propagate the
desire and ability to use the TSC into the tsc_disable flag, previously
this flag only indicated whether the notsc option was passed. This makes
the rare low-res sched_clock() codepath a single branch off a read-mostly
flag.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Add a notifier mechanism to the low level idle loop. You can register a
callback function which gets invoked on entry and exit from the low level idle
loop. The low level idle loop is defined as the polling loop, low-power call,
or the mwait instruction. Interrupts processed by the idle thread are not
considered part of the low level loop.
The notifier can be used to measure precisely how much is spent in useless
execution (or low power mode). The perfmon subsystem uses it to turn on/off
monitoring.
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Profile_pc was broken when using paravirtualization because the
assumption the kernel was running at CPL 0 was violated, causing
bad logic to read a random value off the stack.
The only way to be in kernel lock functions is to be in kernel
code, so validate that assumption explicitly by checking the CS
value. We don't want to be fooled by BIOS / APM segments and
try to read those stacks, so only match KERNEL_CS.
I moved some stuff in segment.h to make it prettier.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
VMI timer code. It works by taking over the local APIC clock when APIC is
configured, which requires a couple hooks into the APIC code. The backend
timer code could be commonized into the timer infrastructure, but there are
some pieces missing (stolen time, in particular), and the exact semantics of
when to do accounting for NO_IDLE need to be shared between different
hypervisors as well. So for now, VMI timer is a separate module.
[Adrian Bunk: cleanups]
Subject: VMI timer patches
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Add VMI SMP boot hook. We emulate a regular boot sequence and use the same
APIC IPI initiation, we just poke magic values to load into the CPU state when
the startup IPI is received, rather than having to jump through a real mode
trampoline.
This is all that was needed to get SMP to work.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
The VMI ROM has a mode where hypercalls can be queued and batched. This turns
out to be a significant win during context switch, but must be done at a
specific point before side effects to CPU state are visible to subsequent
instructions. This is similar to the MMU batching hooks already provided.
The same hooks could be used by the Xen backend to implement a context switch
multicall.
To explain a bit more about lazy modes in the paravirt patches, basically, the
idea is that only one of lazy CPU or MMU mode can be active at any given time.
Lazy MMU mode is similar to this lazy CPU mode, and allows for batching of
multiple PTE updates (say, inside a remap loop), but to avoid keeping some
kind of state machine about when to flush cpu or mmu updates, we just allow
one or the other to be active. Although there is no real reason a more
comprehensive scheme could not be implemented, there is also no demonstrated
need for this extra complexity.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
The VMI backend uses explicit page type notification to track shadow page
tables. The allocation of page table roots is especially tricky. We need to
clone the root for non-PAE mode while it is protected under the pgd lock to
correctly copy the shadow.
We don't need to allocate pgds in PAE mode, (PDPs in Intel terminology) as
they only have 4 entries, and are cached entirely by the processor, which
makes shadowing them rather simple.
For base page table level allocation, pmd_populate provides the exact hook
point we need. Also, we need to allocate pages when splitting a large page,
and we must release pages before returning the page to any free pool.
Despite being required with these slightly odd semantics for VMI, Xen also
uses these hooks to determine the exact moment when page tables are created or
released.
AK: All nops for other architectures
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
ARCH_HAVE_XTIME_LOCK is used by x86_64 arch . This arch needs to place a
read only copy of xtime_lock into vsyscall page. This read only copy is
named __xtime_lock, and xtime_lock is defined in
arch/x86_64/kernel/vmlinux.lds.S as an alias. So the declaration of
xtime_lock in kernel/timer.c was guarded by ARCH_HAVE_XTIME_LOCK define,
defined to true on x86_64.
We can get same result with _attribute__((weak)) in the declaration. linker
should do the job.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Convert the PDA code to use %fs rather than %gs as the segment for
per-processor data. This is because some processors show a small but
measurable performance gain for reloading a NULL segment selector (as %fs
generally is in user-space) versus a non-NULL one (as %gs generally is).
On modern processors the difference is very small, perhaps undetectable.
Some old AMD "K6 3D+" processors are noticably slower when %fs is used
rather than %gs; I have no idea why this might be, but I think they're
sufficiently rare that it doesn't matter much.
This patch also fixes the math emulator, which had not been adjusted to
match the changed struct pt_regs.
[frederik.deweerdt@gmail.com: fixit with gdb]
[mingo@elte.hu: Fix KVM too]
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Ian Campbell <Ian.Campbell@XenSource.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Zachary Amsden <zach@vmware.com>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Remove the statically allocated memory to NUMA node hash map in favor of a
dynamically allocated memory to node hash map (it is cache aligned).
This patch has the nice side effect in that it allows the hash map to grow
for systems with large amounts of memory (256GB - 1TB), but suffer from
having small PCI space tacked onto the boot node (which is somewhere
between 192MB to 512MB on the ES7000).
Signed-off-by: Amul Shah <amul.shah@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Rohit Seth <rohitseth@google.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This does user copies in fs write() into the page cache with write combining.
This pushes the destination out of the CPU's cache, but allows higher bandwidth
in some case.
The theory is that the page cache data is usually not touched by the
CPU again and it's better to not pollute the cache with it. Also it is a little
faster.
Signed-off-by: Andi Kleen <ak@suse.de>
acpi_table_parse_madt_family() is also used to parse SRAT entries.
So re-name it to acpi_table_parse_entries(), and re-name the
madt-specific variables within it accordingly.
cosmetic only.
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_madt_entry_handler() is also used for the SRAT,
so re-name it acpi_table_entry_handler().
cosmetic only.
Signed-off-by: Len Brown <len.brown@intel.com>
RFC3530 section 3.1.1 states an NFSv4 client MUST NOT send a request
twice on the same connection unless it is the NULL procedure. Section
3.1.1 suggests that the client should disconnect and reconnect if it
wants to retry a request.
Implement this by adding an rpc_clnt flag that an ULP can use to
specify that the underlying transport should be disconnected on a
major timeout. The NFSv4 client asserts this new flag, and requests
no retries after a minor retransmit timeout.
Note that disconnecting on a retransmit is in general not safe to do
if the RPC client does not reuse the TCP port number when reconnecting.
See http://bugzilla.linux-nfs.org/show_bug.cgi?id=6
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Len Brown <lenb@kernel.org> said:
> Okay, but better to use disable_acpi()
> indeed, since this would be the first code not already inside CONFIG_ACPI
> to invoke disable_acpi(), we could define the inline as empty and you could
> then scratch the #ifdef too.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds support for the AMCC Taishan PPC440GX evaluation
board.
This is still an arch/ppc port. I'm aware that the move of
4xx to arch/powerpc is making good progress right now. So this
patch is mainly intended to make the Taishan support available
for the community right now.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent vDSO consolidation patches broke powerpc due to a mistake
in the definition of MAXPAGES constants. This fixes it by moving to
a dynamically allocated array of pages instead as I don't like much
hard coded size limits. Also move the vdso initialisation to an initcall
since it doesn't really need to be done -that- early.
Applogies for not catching the breakage earlier, Roland _did_ CC me on
his patches a while ago, I got busy with other things and forgot to test
them.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
During ppc64+ppc merge virtual DMA code for floppy driver was not
ported. This patch restores virtual DMA support for floppy in new
powerpc target.
It is necessary at least on Pegasos and AmigaOne machines for the
floppy drive to function. ISA DMA controller works incorrectly there
due to its addressing limitations.
Virtual DMA mode is activated by floppy=nodma option passed to the
kernel (or module). There's no automatic switch like on i386.
Signed-off-by: Pavel Fedin <sonic_amiga@rambler.ru>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is used by the libc for parsing CPU capability flags passed
via the ELF auxvt, needed for run-time selection of atomic opcodes
amongst other things.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>