Commit Graph

78 Commits

Author SHA1 Message Date
Mike Accetta ed45666271 md: fix bug in error handling during raid1 repair
If raid1/repair (which reads all block and fixes any differences it finds)
hits a read error, it doesn't reset the bio for writing before writing
correct data back, so the read error isn't fixed, and the device probably
gets a zero-length write which it might complain about.

Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-06-16 13:16:15 -07:00
NeilBrown dd00a99e7a md: avoid a possibility that a read error can wrongly propagate through md/raid1 to a filesystem.
When a raid1 has only one working drive, we want read error to propagate up
to the filesystem as there is no point failing the last drive in an array.

Currently the code perform this check is racy.  If a write and a read a
both submitted to a device on a 2-drive raid1, and the write fails followed
by the read failing, the read will see that there is only one working drive
and will pass the failure up, even though the one working drive is actually
the *other* one.

So, tighten up the locking.

Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-10 09:26:53 -07:00
Linus Torvalds 44ce6294d0 Revert "md: improve partition detection in md array"
This reverts commit 5b479c91da.

Quoth Neil Brown:

  "It causes an oops when auto-detecting raid arrays, and it doesn't
   seem easy to fix.

   The array may not be 'open' when do_md_run is called, so
   bdev->bd_disk might be NULL, so bd_set_size can oops.

   This whole approach of opening an md device before it has been
   assembled just seems to get more and more painful.  I think I'm going
   to have to come up with something clever to provide both backward
   comparability with usage expectation, and sane integration into the
   rest of the kernel."

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-09 18:51:36 -07:00
NeilBrown 5b479c91da md: improve partition detection in md array
md currently uses ->media_changed to make sure rescan_partitions
is call on md array after they are assembled.

However that doesn't happen until the array is opened, which is later
than some people would like.

So use blkdev_ioctl to do the rescan immediately that the
array has been assembled.

This means we can remove all the ->change infrastructure as it was only used
to trigger a partition rescan.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-09 12:30:57 -07:00
NeilBrown 2a2275d630 [PATCH] md: fix potential memalloc deadlock in md
If a GFP_KERNEL allocation is attempted in md while the mddev_lock is held,
it is possible for a deadlock to eventuate.

This happens if the array was marked 'clean', and the memalloc triggers a
write-out to the md device.

For the writeout to succeed, the array must be marked 'dirty', and that
requires getting the mddev_lock.

So, before attempting a GFP_KERNEL allocation while holding the lock, make
sure the array is marked 'dirty' (unless it is currently read-only).

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-01-26 13:51:00 -08:00
NeilBrown 3eda22d19b [PATCH] md: make 'repair' actually work for raid1
When 'repair' finds a block that is different one the various parts of the
mirror.  it is meant to write a chosen good version to the others.  However it
currently writes out the original data to each.  The memcpy to make all the
data the same is missing.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-01-26 13:50:59 -08:00
Lars Ellenberg e3881a6816 [PATCH] md: pass down BIO_RW_SYNC in raid{1,10}
md raidX make_request functions strip off the BIO_RW_SYNC flag, thus
introducing additional latency.

Fixing this in raid1 and raid10 seems to be straightforward enough.

For our particular usage case in DRBD, passing this flag improved some
initialization time from ~5 minutes to ~5 seconds.

Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Lars Ellenberg <lars@linbit.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2007-01-11 18:18:21 -08:00
NeilBrown 802ba064c4 [PATCH] md: Don't assume that READ==0 and WRITE==1 - use the names explicitly
Thanks Jens for alerting me to this.

Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <raziebe@gmail.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-13 09:05:48 -08:00
NeilBrown 1757128438 [PATCH] md: assorted md and raid1 one-liners
Fix few bugs that meant that:
  - superblocks weren't alway written at exactly the right time (this
    could show up if the array was not written to - writting to the array
    causes lots of superblock updates and so hides these errors).

  - restarting device recovery after a clean shutdown (version-1 metadata
    only) didn't work as intended (or at all).

1/ Ensure superblock is updated when a new device is added.
2/ Remove an inappropriate test on MD_RECOVERY_SYNC in md_do_sync.
   The body of this if takes one of two branches depending on whether
   MD_RECOVERY_SYNC is set, so testing it in the clause of the if
   is wrong.
3/ Flag superblock for updating after a resync/recovery finishes.
4/ If we find the neeed to restart a recovery in the middle (version-1
   metadata only) make sure a full recovery (not just as guided by
   bitmaps) does get done.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-10 09:57:21 -08:00
Randy Dunlap 969b755aad [PATCH] md: fix printk format warnings, seen on powerpc64:
drivers/md/raid1.c:1479: warning: long long unsigned int format, long unsigned int arg (arg 4)
drivers/md/raid10.c:1475: warning: long long unsigned int format, long unsigned int arg (arg 4)

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-28 11:30:52 -07:00
NeilBrown 0d12922823 [PATCH] md: define ->congested_fn for raid1, raid10, and multipath
raid1, raid10 and multipath don't report their 'congested' status through
bdi_*_congested, but should.

This patch adds the appropriate functions which just check the 'congested'
status of all active members (with appropriate locking).

raid1 read_balance should be modified to prefer devices where
bdi_read_congested returns false.  Then we could use the '&' branch rather
than the '|' branch.  However that should would need some benchmarking first
to make sure it is actually a good idea.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:18 -07:00
NeilBrown c04be0aa82 [PATCH] md: Improve locking around error handling
The error handling routines don't use proper locking, and so two concurrent
errors could trigger a problem.

So:
  - use test-and-set and test-and-clear to synchonise
    the In_sync bits with the ->degraded count
  - use the spinlock to protect updates to the
    degraded count (could use an atomic_t but that
    would be a bigger change in code, and isn't
    really justified)
  - remove un-necessary locking in raid5

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:18 -07:00
NeilBrown 11ce99e625 [PATCH] md: Remove working_disks from raid1 state data
It is equivalent to conf->raid_disks - conf->mddev->degraded.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:17 -07:00
NeilBrown 867868fb55 [PATCH] md: Factor out part of raid1d into a separate function
raid1d has toooo many nested block, so take the fix_read_error functionality
out into a separate function.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:17 -07:00
NeilBrown 850b2b420c [PATCH] md: replace magic numbers in sb_dirty with well defined bit flags
Instead of magic numbers (0,1,2,3) in sb_dirty, we have
some flags instead:
MD_CHANGE_DEVS
   Some device state has changed requiring superblock update
   on all devices.
MD_CHANGE_CLEAN
   The array has transitions from 'clean' to 'dirty' or back,
   requiring a superblock update on active devices, but possibly
   not on spares
MD_CHANGE_PENDING
   A superblock update is underway.

We wait for an update to complete by waiting for all flags to be clear.  A
flag can be set at any time, even during an update, without risk that the
change will be lost.

Stop exporting md_update_sb - isn't needed.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-03 08:04:17 -07:00
NeilBrown ddac7c7e3a [PATCH] md: Fix issues with referencing rdev in md/raid1
We need to be careful when referencing mirrors[i].rdev.  It can disappear
under us at various times.

So:
  fix a couple of problem places.
  comment a couple of non-problem places
  move an 'atomic_add' which deferences rdev down a little
    way to some where where it is sure to not be NULL.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-01 11:39:08 -07:00
NeilBrown 6394cca548 [PATCH] md: fix recent breakage of md/raid1 array checking
A recent patch broke the ability to do a user-request check of a raid1.
This patch fixes the breakage and also moves a comment that was dislocated
by the same patch.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-08-27 11:01:31 -07:00
NeilBrown d695043259 [PATCH] md: include sector number in messages about corrected read errors
This is generally useful, but particularly helps see if it is the same sector
that always needs correcting, or different ones.

[akpm@osdl.org: fix printk warnings]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-10 13:24:17 -07:00
NeilBrown 5e3db645f8 [PATCH] md: fix usage of wrong variable in raid1
Though it rarely matters, we should be using 's' rather than r1_bio->sector
here.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-10 13:24:17 -07:00
NeilBrown 07d84d109d [PATCH] md: Allow re-add to work on array without bitmaps
When an array has a bitmap, a device can be removed and re-added and only
blocks changes since the removal (as recorded in the bitmap) will be resynced.

It should be possible to do a similar thing to arrays without bitmaps.  i.e.
if a device is removed and re-added and *no* changes have been made in the
interim, then the add should not require a resync.

This patch allows that option.  This means that when assembling an array one
device at a time (e.g.  during device discovery) the array can be enabled
read-only as soon as enough devices are available, but extra devices can still
be added without causing a resync.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:39 -07:00
NeilBrown 5fd6c1dce0 [PATCH] md: allow checkpoint of recovery with version-1 superblock
For a while we have had checkpointing of resync.  The version-1 superblock
allows recovery to be checkpointed as well, and this patch implements that.

Due to early carelessness we need to add a feature flag to signal that the
recovery_offset field is in use, otherwise older kernels would assume that a
partially recovered array is in fact fully recovered.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:37 -07:00
NeilBrown c70810b327 [PATCH] md: reformat code in raid1_end_write_request to avoid goto
A recent change made this goto unnecessary, so reformat the code to make it
clearer what is happening.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-26 09:58:36 -07:00
NeilBrown 5e7dd2ab6b [PATCH] md: Fix 'rdev->nr_pending' count when retrying barrier requests
When retrying a failed BIO_RW_BARRIER request, we need to keep the reference
in ->nr_pending over the whole retry.  Currently, we only hold the reference
if the failed request is the *last* one to finish - which is silly, because it
would normally be the first to finish.

So move the rdev_dec_pending call up into the didn't-fail branch.  As the rdev
isn't used in the later code, calling rdev_dec_pending earlier doesn't hurt.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-01 18:17:42 -07:00
NeilBrown 62de608da0 [PATCH] md: Improve detection of lack of barrier support in raid1
Move the test for 'do barrier work' down a bit so that if the first write to a
raid1 is a BIO_RW_BARRIER write, the checking done by superblock writes will
cause the right thing to happen.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-01 18:17:42 -07:00
NeilBrown bea2771871 [PATCH] md: Change ENOTSUPP to EOPNOTSUPP
Because that is what you get if a BIO_RW_BARRIER isn't supported!

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-01 18:17:42 -07:00
Eric Sesterhenn 9e77c485f7 BUG_ON() Conversion in md/raid1.c
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away

Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-04-01 01:08:49 +02:00
NeilBrown 6b1117d505 [PATCH] md: Don't clear bits in bitmap when writing to one device fails during recovery
Currently a device failure during recovery leaves bits set in the bitmap.
This normally isn't a problem as the offending device will be rejected because
of errors.  However if device re-adding is being used with non-persistent
bitmaps, this can be a problem.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-31 12:19:01 -08:00
NeilBrown 2f889129de [PATCH] md: Restore 'remaining' count when retrying an write operation
When retrying a write due to barrier failure, we don't reset 'remaining', so
it goes negative and never hits 0 again.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-27 08:45:03 -08:00
NeilBrown 63c70c4f3a [PATCH] md: Split reshape handler in check_reshape and start_reshape
check_reshape checks validity and does things that can be done instantly -
like adding devices to raid1.  start_reshape initiates a restriping process to
convert the whole array.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-27 08:45:02 -08:00
NeilBrown f67055780c [PATCH] md: Checkpoint and allow restart of raid5 reshape
We allow the superblock to record an 'old' and a 'new' geometry, and a
position where any conversion is up to.  The geometry allows for changing
chunksize, layout and level as well as number of devices.

When using verion-0.90 superblock, we convert the version to 0.91 while the
conversion is happening so that an old kernel will refuse the assemble the
array.  For version-1, we use a feature bit for the same effect.

When starting an array we check for an incomplete reshape and restart the
reshape process if needed.  If the reshape stopped at an awkward time (like
when updating the first stripe) we refuse to assemble the array, and let
user-space worry about it.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-27 08:45:01 -08:00
NeilBrown 04b857f74c [PATCH] md: Fix several raid1 bugs which cause a memory leak
- wrong test for 'is this a BARRIER bio'
- not freeing on all possible paths.
- using r1_bio after freeing it.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-09 19:47:37 -08:00
Arjan van de Ven 858119e159 [PATCH] Unlinline a bunch of other functions
Remove the "inline" keyword from a bunch of big functions in the kernel with
the goal of shrinking it by 30kb to 40kb

Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-14 18:27:06 -08:00
NeilBrown 4dbcdc751c [PATCH] md: count corrected read errors per drive
Store this total in superblock (As appropriate), and make it available to
userspace via sysfs.

Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:09 -08:00
NeilBrown d9d166c2a9 [PATCH] md: allow array level to be set textually via sysfs
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:09 -08:00
NeilBrown 03c902e17f [PATCH] md: fix rdev->pending counts in raid1
When we do a user-requested check/repair, we lose count of the outstanding
requests...

Also make sure that when anything is written to md/sync_action, the
RECOVERY_NEEDED flag is set and the thread is woken up so any changes take
effect.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:08 -08:00
NeilBrown 1345b1d8ad [PATCH] md: define and use safe_put_page for md
md sometimes call put_page on NULL pointers (treating it like kfree).  This is
not safe, so define and use a 'safe_put_page' which checks for NULL.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:07 -08:00
NeilBrown 097426f689 [PATCH] md: fix possible problem in raid1/raid10 error overwriting
The code to overwrite/reread for addressing read errors in raid1/raid10
currently assumes that the read will not alter the buffer which could be used
to write to the next device.  This is not a safe assumption to make.

So we split the loops into a overwrite loop and a separate re-read loop, so
that the writing is complete before reading is attempted.

Cc: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:06 -08:00
NeilBrown 2604b703b6 [PATCH] md: remove personality numbering from md
md supports multiple different RAID level, each being implemented by a
'personality' (which is often in a separate module).

These personalities have fairly artificial 'numbers'.  The numbers
are use to:
 1- provide an index into an array where the various personalities
    are recorded
 2- identify the module (via an alias) which implements are particular
    personality.

Neither of these uses really justify the existence of personality numbers.
The array can be replaced by a linked list which is searched (array lookup
only happens very rarely).  Module identification can be done using an alias
based on level rather than 'personality' number.

The current 'raid5' modules support two level (4 and 5) but only one
personality.  This slight awkwardness (which was handled in the mapping from
level to personality) can be better handled by allowing raid5 to register 2
personalities.

With this change in place, the core md module does not need to have an
exhaustive list of all possible personalities, so other personalities can be
added independently.

This patch also moves the check for chunksize being non-zero into the ->run
routines for the personalities that need it, rather than having it in core-md.
 This has a side effect of allowing 'faulty' and 'linear' not to have a
chunk-size set.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:06 -08:00
NeilBrown 9ffae0cf3e [PATCH] md: convert md to use kzalloc throughout
Replace multiple kmalloc/memset pairs with kzalloc calls.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:05 -08:00
NeilBrown 2d1f3b5d1b [PATCH] md: clean up 'page' related names in md
Substitute:

  page_cache_get -> get_page
  page_cache_release -> put_page
  PAGE_CACHE_SHIFT -> PAGE_SHIFT
  PAGE_CACHE_SIZE -> PAGE_SIZE
  PAGE_CACHE_MASK -> PAGE_MASK
  __free_page -> put_page

because we aren't using the page cache, we are just using pages.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:05 -08:00
NeilBrown 220946c901 [PATCH] md: make sure read error on last working drive of raid1 actually returns failure
We are inadvertently setting the R1BIO_Uptodate bit on read errors when we
decide not to try correcting (because there are no other working devices).
This means that the read error is reported to the client as success.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:04 -08:00
NeilBrown d11c171e63 [PATCH] md: allow raid1 to check consistency
Where performing a user-requested 'check' or 'repair', we read all readable
devices, and compare the contents.  We only write to blocks which had read
errors, or blocks with content that differs from the first good device found.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:04 -08:00
NeilBrown cf30a473a0 [PATCH] md: handle errors when read-only
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:04 -08:00
NeilBrown 69382e8537 [PATCH] md: better handling for read error in raid1 during resync
Handling of read errors during resync is separate from handling of read errors
during normal IO in raid1.  A previous patch added support for read errors
during normal IO.  This one adds support for read errors during resync or
recovery.

The key differences are that we don't need to freeze the array, because the
normal handling of resync means that this part of the array will be idle
except for resync, and the read/overwrite/re-read is needed in a separate
piece of code.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:04 -08:00
NeilBrown 3e198f7826 [PATCH] md: tidyup some issues with raid1 resync and prepare for catching read errors
We are dereferencing ->rdev without an rcu lock!

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:03 -08:00
NeilBrown ddaf22abaa [PATCH] md: attempt to auto-correct read errors in raid1
On a read-error we suspend the array, then synchronously read the block from
other arrays until we find one where we can read it.  Then we try writing the
good data back everywhere and make sure it works.  If any write or subsequent
read fails, only then do we fail the device out of the array.

To be able to suspend the array, we need to also keep track of how many
requests are queued for handling by raid1d.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:03 -08:00
NeilBrown b15c2e57f0 [PATCH] md: move bitmap_create to after md array has been initialised
This is important because bitmap_create uses
  mddev->resync_max_sectors
and that doesn't have a valid value until after the array
has been initialised (with pers->run()).
[It doesn't make a difference for current personalities that
 support bitmaps, but will make a difference for raid10]

This has the added advantage of meaning with can move the thread->timeout
manipulation inside the bitmap.c code instead of sprinkling identical code
throughout all personalities.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:03 -08:00
NeilBrown 17999be4aa [PATCH] md: improve raid1 "IO Barrier" concept
raid1 needs to put up a barrier to new requests while it does resync or other
background recovery.  The code for this is currently open-coded, slighty
obscure by its use of two waitqueues, and not documented.

This patch gathers all the related code into 4 functions, and includes a
comment which (hopefully) explains what is happening.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-06 08:34:01 -08:00
NeilBrown 3795bb0fc5 [PATCH] md: fix a use-after-free bug in raid1
Who would submit code with a FIXME like that in it !!!!

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-12-12 09:06:04 -08:00
NeilBrown 6aea114a72 [PATCH] md: fix --re-add for raid1 and raid6
If you have an array with a write-intent-bitmap, and you remove a device, then
re-add it, a full recovery isn't needed.  We detect a re-add by looking at
saved_raid_disk.  For raid1, it doesn't matter which disk it was, only whether
or not it was an active device.  The old code being removed set a value of
'mirror' which was then ignored, so it can go.  The changed code performs the
correct check.

For raid6, if there are two missing devices, make sure we chose the right slot
on --re-add rather than always the first slot.

Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-11-28 14:42:26 -08:00