For consistency with the rest of the file rename function and parameter to
be consistent with the reset of the common file.
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move the i2c_dw_plat_prepare_clk funciton to common file in preparation
for its use also by the master driver.
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to data sheet SCL timing parameters and DW_IC_CON SPEED mode
bits are not used when operating in slave mode.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Luis Oliveira <lolivei@synopsys.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"This contains two bigger than usual tree-wide changes this time. They
all have proper acks, caused no merge conflicts in linux-next where
they have been for a while. They are namely:
- to-gpiod conversion of the i2c-gpio driver and its users (touching
arch/* and drivers/mfd/*)
- adding a sbs-manager based on I2C core updates to SMBus alerts
(touching drivers/power/*)
Other notable changes:
- i2c_boardinfo can now carry a dev_name to be used when the device
is created. This is because some devices in ACPI world need fixed
names to find the regulators.
- the designware driver got a long discussed overhaul of its PM
handling. img-scb and davinci got PM support, too.
- at24 driver has way better OF support. And it has a new maintainer.
Thanks Bartosz for stepping up!
The rest is regular driver updates and fixes"
* 'i2c/for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (55 commits)
ARM: sa1100: simpad: Correct I2C GPIO offsets
i2c: aspeed: Deassert reset in probe
eeprom: at24: Add OF device ID table
MAINTAINERS: new maintainer for AT24 driver
i2c: nuc900: remove platform_data, too
i2c: thunderx: Remove duplicate NULL check
i2c: taos-evm: Remove duplicate NULL check
i2c: Make i2c_unregister_device() NULL-aware
i2c: xgene-slimpro: Support v2
i2c: mpc: remove useless variable initialization
i2c: omap: Trigger bus recovery in lockup case
i2c: gpio: Add support for named gpios in DT
dt-bindings: i2c: i2c-gpio: Add support for named gpios
i2c: gpio: Local vars in probe
i2c: gpio: Augment all boardfiles to use open drain
i2c: gpio: Enforce open drain through gpiolib
gpio: Make it possible for consumers to enforce open drain
i2c: gpio: Convert to use descriptors
power: supply: sbs-message: fix some code style issues
power: supply: sbs-battery: remove unchecked return var
...
In order to use i2c from a cold boot, the i2c peripheral must be taken
out of reset. We request a shared reset controller each time a bus
driver is loaded, as the reset is shared between the 14 i2c buses.
On remove the reset is asserted, which only touches the hardware once
the last i2c bus is removed.
The reset is required as the I2C buses will not work without releasing
the reset. Previously the driver only worked with out of tree hacks
that released this reset before the driver was loaded. Update the
device tree bindings to reflect this.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch supports xgene-slimpro-i2c v2 which uses the non-cachable memory
as the PCC shared memory.
Signed-off-by: Hoan Tran <hotran@apm.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
cppcheck rightfully says:
drivers/i2c/busses/i2c-mpc.c:329: style: Variable 'node' is reassigned a value before the old one has been used.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
A very conservative check for bus activity (to prevent interference
in multimaster setups) prevented the bus recovery methods from being
triggered in the case that SDA or SCL was stuck low.
This defeats the purpose of the recovery mechanism, which was introduced
for exactly this situation (a slave device keeping SDA pulled down).
Also added a check to make sure SDA is low before attempting recovery.
If SDA is not stuck low, recovery will not help, so we can skip it.
Note that bus lockups can persist across reboots. The only other options
are to reset or power cycle the offending slave device, and many i2c
slaves do not even have a reset pin.
If we see that one of the lines is low for the entire timeout duration,
we can actually be sure that there is no other master driving the bus.
It is therefore save for us to attempt a bus recovery.
Signed-off-by: Claudio Foellmi <claudio.foellmi@ergon.ch>
Tested-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
[wsa: fixed one return code to -EBUSY]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This adds support for using the "sda" and "scl" GPIOs in
device tree instead of anonymously using index 0 and 1 of
the "gpios" property.
We add a helper function to retrieve the GPIO descriptors
and some explicit error handling since the probe may have
to be deferred. At least this happened to me when moving
to using named "sda" and "scl" lines (all of a sudden this
started to probe before the GPIO driver) so we need to
gracefully defer probe when we ge -ENOENT in the error
pointer.
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By creating local variables for *dev and *np, the code become
much easier to read, in my opinion.
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The I2C GPIO bitbang driver currently emulates open drain
behaviour by implementing what the gpiolib already does:
not actively driving the line high, instead setting it to
input.
This makes no sense. Use the new facility in gpiolib to
request the lines enforced into open drain mode, and let
the open drain emulation already present in the gpiolib
kick in and handle this.
As a bonus: if the GPIO driver in the back-end actually
supports open drain in hardware using the .set_config()
callback, it will be utilized. That's correct: we never
used that hardware feature before, instead relying on
emulating open drain even if the GPIO controller could
actually handle this for us.
Users will sometimes get messages like this:
gpio-485 (?): enforced open drain please flag it properly
in DT/ACPI DSDT/board file
gpio-486 (?): enforced open drain please flag it properly
in DT/ACPI DSDT/board file
i2c-gpio gpio-i2c: using lines 485 (SDA) and 486 (SCL)
Which is completely proper: since the line is used as
open drain, it should actually be flagged properly with
e.g.
gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>,
<&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
Or similar facilities in board file descriptor tables
or ACPI DSDT.
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the GPIO-based I2C-driver to using GPIO
descriptors instead of the old global numberspace-based
GPIO interface. We:
- Convert the driver to unconditionally grab two GPIOs
from the device by index 0 (SDA) and 1 (SCL) which
will work fine with device tree and descriptor tables.
The existing device trees will continue to work just
like before, but without any roundtrip through the
global numberspace.
- Brutally convert all boardfiles still passing global
GPIOs by registering descriptor tables associated with
the devices instead so this driver does not need to keep
supporting passing any GPIO numbers as platform data.
There is no stepwise approach as elegant as this, I
strongly prefer this big hammer over any antsteps for this
conversion. This way the old GPIO numbers go away and
NEVER COME BACK.
Special conversion for the different boards utilizing
I2C-GPIO:
- EP93xx (arch/arm/mach-ep93xx): pretty straight forward as
all boards were using the same two GPIO lines, just define
these two in a lookup table for "i2c-gpio" and register
these along with the device. None of them define any
other platform data so just pass NULL as platform data.
This platform selects GPIOLIB so all should be smooth.
The pins appear on a gpiochip for bank "G" as pins 1 (SDA)
and 0 (SCL).
- IXP4 (arch/arm/mach-ixp4): descriptor tables have to
be registered for each board separately. They all use
"IXP4XX_GPIO_CHIP" so it is pretty straight forward.
Most board define no other platform data than SCL/SDA
so they can drop the #include of <linux/i2c-gpio.h> and
assign NULL to platform data.
The "goramo_mlr" (Goramo Multilink Router) board is a bit
worrisome: it implements its own I2C bit-banging in the
board file, and optionally registers an I2C serial port,
but claims the same GPIO lines for itself in the board file.
This is not going to work: there will be competition for the
GPIO lines, so delete the optional extra I2C bus instead, no
I2C devices are registered on it anyway, there are just hints
that it may contain an EEPROM that may be accessed from
userspace. This needs to be fixed up properly by the serial
clock using I2C emulation so drop a note in the code.
- KS8695 board acs5k (arch/arm/mach-ks8695/board-acs5.c)
has some platform data in addition to the pins so it needs to
be kept around sans GPIO lines. Its GPIO chip is named
"KS8695" and the arch selects GPIOLIB.
- PXA boards (arch/arm/mach-pxa/*) use some of the platform
data so it needs to be preserved here. The viper board even
registers two GPIO I2Cs. The gpiochip is named "gpio-pxa" and
the arch selects GPIOLIB.
- SA1100 Simpad (arch/arm/mach-sa1100/simpad.c) defines a GPIO
I2C bus, and the arch selects GPIOLIB.
- Blackfin boards (arch/blackfin/bf533 etc) for these I assume
their I2C GPIOs refer to the local gpiochip defined in
arch/blackfin/kernel/bfin_gpio.c names "BFIN-GPIO".
The arch selects GPIOLIB. The boards get spiked with
IF_ENABLED(I2C_GPIO) but that is a side effect of it
being like that already (I would just have Kconfig select
I2C_GPIO and get rid of them all.) I also delete any
platform data set to 0 as it will get that value anyway
from static declartions of platform data.
- The MIPS selects GPIOLIB and the Alchemy machine is using
two local GPIO chips, one of them has a GPIO I2C. We need
to adjust the local offset from the global number space here.
The ATH79 has a proper GPIO driver in drivers/gpio/gpio-ath79.c
and AFAICT the chip is named "ath79-gpio" and the PB44
PCF857x expander spawns from this on GPIO 1 and 0. The latter
board only use the platform data to specify pins so it can be
cut altogether after this.
- The MFD Silicon Motion SM501 is a special case. It dynamically
spawns an I2C bus off the MFD using sm501_create_subdev().
We use an approach to dynamically create a machine descriptor
table and attach this to the "SM501-LOW" or "SM501-HIGH"
gpiochip. We use chip-local offsets to grab the right lines.
We can get rid of two local static inline helpers as part
of this refactoring.
Cc: Steven Miao <realmz6@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Wu, Aaron <Aaron.Wu@analog.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Prior to this commit the smbalert_irq was handling in the hard irq
context. This change switch to using a thread irq which avoids the need
for the work thread. Using threaded irq also removes the need for the
edge_triggered flag as the enabling / disabling of the hard irq for level
triggered interrupts will be handled by the irq core.
Without this change have an irq connected to something like an i2c gpio
resulted in a null ptr deferences. Specifically handle_nested_irq calls
the threaded irq handler.
There are currently 3 in tree drivers affected by this change.
i2c-parport driver calls i2c_handle_smbus_alert in a hard irq context.
This driver use edge trigger interrupts which skip the enable / disable
calls. But it still need to handle the smbus transaction on a thread. So
the work thread is kept for this driver.
i2c-parport-light & i2c-thunderx-pcidrv provide the irq number in the
setup which will result in the thread irq being used.
i2c-parport-light is edge trigger so the enable / disable call was
skipped as well.
i2c-thunderx-pcidrv is getting the edge / level trigger setting from of
data and was setting the flag as required. However the irq core should
handle this automatically.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-img-scb driver already dynamically enables / disables clocks to
save power, but doesn't use the runtime PM framework. Convert the
driver to use runtime PM, so that dynamic clock management will be
disabled when runtime PM is disabled, and so that autosuspend can be
used to avoid unnecessarily disabling and re-enabling clocks repeatedly
during a sequence of transactions.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use of_property_read_bool to check for the existence of a property.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the restriction that the parent clock has to be a specific frequency
and also allow any speed to be supported.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add device-properties to make the bq24292i charger connected to
the bus get its input-current-limit from the fusb302 Type-C port
controller which is used on boards with the cht-wc PMIC,
as well as regulator_init_data for the 5V boost converter on
the bq24292i.
Since this means we now hook-up the bq24292i to the fusb302 Type-C port
controller add a check for the ACPI device which instantiates the fusb302.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes this warning (found by build testing with 64bit):
format ‘%i’ expects argument of type ‘int’, but argument 3 has type
‘size_t {aka long unsigned int}’ [-Wformat=]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Otherwise we can get the following if the fck alias is missing:
Unable to handle kernel paging request at virtual address fffffffe
...
PC is at clk_get_rate+0x8/0x10
LR is at omap_i2c_probe+0x278/0x6ec
...
[<c056eb08>] (clk_get_rate) from [<c06f4f08>] (omap_i2c_probe+0x278/0x6ec)
[<c06f4f08>] (omap_i2c_probe) from [<c0610944>] (platform_drv_probe+0x50/0xb0)
[<c0610944>] (platform_drv_probe) from [<c060e900>] (driver_probe_device+0x264/0x2ec)
[<c060e900>] (driver_probe_device) from [<c060cda0>] (bus_for_each_drv+0x70/0xb8)
[<c060cda0>] (bus_for_each_drv) from [<c060e5b0>] (__device_attach+0xcc/0x13c)
[<c060e5b0>] (__device_attach) from [<c060db10>] (bus_probe_device+0x88/0x90)
[<c060db10>] (bus_probe_device) from [<c060df68>] (deferred_probe_work_func+0x4c/0x14c)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the of_device_get_match_data() helper instead of open coding.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver needs to handle the flag I2C_M_RECV_LEN during receive to
support SMBus emulation.
Update receive logic to handle the case where the length is received
as the first byte of a transaction.
Also update the code to handle I2C_CLIENT_PEC, which is set when the
client sends a packet error checking code byte.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Kamlakant Patel <kamlakant.patel@cavium.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Get the input clock frequency to the controller from the linux clk
API, if it is available. This allows us to pass in the block input
frequency either from ACPI (using APD) or from device tree.
The old hardcoded frequency is used as default for backwards compatibility.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Kamlakant Patel <kamlakant.patel@cavium.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Don't populate const array supported_speeds on the stack, instead
make it static. Makes the object code smaller by 150 bytes:
Before:
text data bss dec hex filename
8474 1440 0 9914 26ba i2c-designware-platdrv.o
After:
text data bss dec hex filename
8324 1440 0 9764 2624 i2c-designware-platdrv.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
66AK2G has I2C instances that are not apart of the ALWAYS_ON power domain
unlike other Keystone 2 SoCs and OMAPL138. Therefore, pm_runtime
is required to insure the power domain used by the specific I2C instance is
properly turned on along with its functional clock.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SMBUS_BLOCK_DATA transactions might fail due to a race condition with
the IMC (Integrated Micro Controller), even when the IMC semaphore
is used.
This bug has been reported and confirmed by AMD, who suggested as a
solution an IMC firmware upgrade (obtained via BIOS update) and
disabling the IMC during SMBUS_BLOCK_DATA transactions.
Even without the IMC upgrade, the SMBUS is much more stable with this
patch.
Tested on a Bettong-alike board.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
AMD Family 17h uses the KERNCZ SMBus controller. While its documentation
is not publicly available, it is documented in the BIOS and Kernel
Developer’s Guide for AMD Family 15h Models 60h-6Fh Processors.
On this SMBus controller, the port select register is at PMx register
0x02, bit 4:3 (PMx00 register bit 20:19).
Without this patch, the 4 SMBus channels on AMD Family 17h chips are
mirrored and report the same chips on all channels.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The arguments for SDA and SCL were swapped. Fix it.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some SoC share one irq number between I2C controllers.
For example, on the LS2088 board, I2C 1 and I2C 2 share
one irq number. In this case, only one I2C controller
can register successfully, and others will fail.
Signed-off-by: Wei Jinhua <wei.jinhua1@zte.com.cn>
Reviewed-by: Jiang Biao <jiang.biao2@zte.com.cn>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit b6c159a9cb ("i2c: ismt: Don't duplicate the receive length for
block reads") broke I2C block reads. It aimed to fix normal SMBus block
read, but changed the correct behavior of I2C block read in the process.
According to Documentation/i2c/smbus-protocol, one vital difference
between normal SMBus block read and I2C block read is that there is no
byte count prefixed in the data sent on the wire:
SMBus Block Read: i2c_smbus_read_block_data()
S Addr Wr [A] Comm [A]
S Addr Rd [A] [Count] A [Data] A [Data] A ... A [Data] NA P
I2C Block Read: i2c_smbus_read_i2c_block_data()
S Addr Wr [A] Comm [A]
S Addr Rd [A] [Data] A [Data] A ... A [Data] NA P
Therefore the two transaction types need to be processed differently in
the driver by copying of the dma_buffer as done previously for the
I2C_SMBUS_I2C_BLOCK_DATA case.
Fixes: b6c159a9cb ("i2c: ismt: Don't duplicate the receive length for block reads")
Signed-off-by: Pontus Andersson <epontan@gmail.com>
Tested-by: Stephen Douthit <stephend@adiengineering.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c fixes from Wolfram Sang:
"I2C has three driver fixes for the newly introduced drivers and one ID
addition for the i801 driver"
* 'i2c/for-current-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-stm32f7: make structure stm32f7_setup static const
i2c: ensure termination of *_device_id tables
i2c: i801: Add support for Intel Cedar Fork
i2c: stm32f7: fix setup structure
The structure stm32f7_setup is local to the source and does not need
to be in global scope, make it static const.
Cleans up sparse warning:
symbol 'stm32f7_setup' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make sure (of/i2c/platform)_device_id tables are NULL terminated.
Found by coccinelle spatch "misc/of_table.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add PCI ID for Intel Cedar Fork PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C drive setup structure is not properly allocated.
Make it static instead of pointer to store driver data.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As reported by Rajat Jain, there are problems when ACPI operation
region handlers or similar, called at the ->resume_early() time, for
I2C client devices try to access an I2C controller that has already
been suspended at that point. To avoid that, move the suspend/resume
of i2c-designware-platdrv to the late/early stages, respectively.
While at it, avoid resuming the device from runtime suspend in the
driver's ->suspend callback which isn't particularly nice. [A better
approach would be to make the driver track the PM state of the device
so that it doesn't need to resume it in ->suspend, so implement it.]
First, drop dw_i2c_plat_suspend() added by commit a23318feef (i2c:
designware: Fix system suspend) and rename dw_i2c_plat_runtime_suspend()
back to dw_i2c_plat_suspend().
Second, point the driver's ->late_suspend and ->early_resume
callbacks, rather than its ->suspend and ->resume callbacks,
to dw_i2c_plat_suspend() and dw_i2c_plat_resume(), respectively,
so that they are not executed in parallel with each other, for
example if runtime resume of the device takes place during system
suspend.
Finally, add "suspended" and "skip_resume" flags to struct dw_i2c_dev
and make dw_i2c_plat_suspend() and dw_i2c_plat_resume() use them to
avoid suspending or resuming the device twice in a row and to avoid
resuming a previously runtime-suspended device during system resume.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Johannes Stezenbach <js@sig21.net>
Tested-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The power management handling in dw_i2c_plat_probe() is somewhat
messy and it is rather hard to figure out the code intention for
the case when pm_disabled is set. In that case, the driver doesn't
enable runtime PM at all, but in addition to that it calls
pm_runtime_forbid() as though it wasn't sure if runtime PM might
be enabled for the device later by someone else.
Although that concern doesn't seem to be actually valid, the
device is clearly still expected to be PM-capable even in the
pm_disabled set case, so a better approach would be to enable
runtime PM for it unconditionally and prevent it from being
runtime-suspended by using pm_runtime_get_noresume().
Make the driver do that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update my imgtec.com and personal email address to my kernel.org one in
a few places as MIPS will soon no longer be part of Imagination
Technologies, and add mappings in .mailcap so get_maintainer.pl reports
the right address.
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds initial support for the STM32F7 I2C controller.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch uses a more generic definition of speed enum for i2c-stm32f4
driver.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Reviewed-by: Ludovic BARRE <ludovic.barre@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add driver support for the Altera I2C Controller. The I2C
controller is soft IP for use in FPGAs.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
- new drivers for Spreadtrum I2C, Intel Cherry Trail Whiskey Cove SMBUS
- quite some driver updates
- cleanups for the i2c-mux subsystem
- some subsystem-wide constification
- further cleanup of include/linux/i2c
* 'i2c/for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (50 commits)
i2c: sprd: Fix undefined reference errors
i2c: nomadik: constify amba_id
i2c: versatile: Make i2c_algo_bit_data const
i2c: busses: make i2c_adapter_quirks const
i2c: busses: make i2c_adapter const
i2c: busses: make i2c_algorithm const
i2c: Add Spreadtrum I2C controller driver
dt-bindings: i2c: Add Spreadtrum I2C controller documentation
i2c-cht-wc: make cht_wc_i2c_adap_driver static
MAINTAINERS: Add entry for drivers/i2c/busses/i2c-cht-wc.c
i2c: aspeed: Retain delay/setup/hold values when configuring bus frequency
dt-bindings: i2c: eeprom: Document vendor to be used and deprecated ones
i2c: i801: Restore the presence state of P2SB PCI device after reading BAR
MAINTAINERS: drop entry for Blackfin I2C and Sonic's email
blackfin: merge the two TWI header files
i2c: davinci: Preserve return value of devm_clk_get
i2c: mediatek: Add i2c compatible for MediaTek MT7622
dt-bindings: i2c: Add MediaTek MT7622 i2c binding
dt-bindings: i2c: modify information formats
i2c: mux: i2c-arb-gpio-challenge: allow compiling w/o OF support
...
Since the i2c driver of Spreadtrum can not be build as one module, thus
it should depend on CONFIG_I2C is build in.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Lenovo Miix2 8 DSDT contains an i2c clk / bus speed of 1700000 Hz
for one if its devices, which is not supported.
This is the second DSDT to show up with an unsupported clk in a short
time, remove the hardcoded fix for DSDTs with a 1 MiHz clock and simply
always round down the clk to the nearest supported value.
Reported-by: russianneuromancer@ya.ru
Fixes: 682c6c2188 ("i2c: designware: Some broken DSTDs use 1MiHz ...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make this const as it is only used in a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make these const as they are only stored as a reference in the quirks
field of an i2c_adapter structure, which is const. Done using
Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make these const as they are only used in a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make these const as they are only stored in the algo field of
i2c_adapter structure, which is const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Compare the number of bytes actually seen on the wire to the byte
count field returned by the slave device.
Previously we just overwrote the byte count returned by the slave
with the real byte count and let the caller figure out if the
message was sane.
Signed-off-by: Stephen Douthit <stephend@adiengineering.com>
Tested-by: Dan Priamo <danp@adiengineering.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
According to Table 15-14 of the C2000 EDS (Intel doc #510524) the
rx data pointed to by the descriptor dptr contains the byte count.
desc->rxbytes reports all bytes read on the wire, including the
"byte count" byte. So if a device sends 4 bytes in response to a
block read, on the wire and in the DMA buffer we see:
count data1 data2 data3 data4
0x04 0xde 0xad 0xbe 0xef
That's what we want to return in data->block to the next level.
Instead we were actually prefixing that with desc->rxbytes:
bad
count count data1 data2 data3 data4
0x05 0x04 0xde 0xad 0xbe 0xef
This was discovered while developing a BMC solution relying on the
ipmi_ssif.c driver which was trying to interpret the bogus length
field as part of the IPMI response.
Signed-off-by: Stephen Douthit <stephend@adiengineering.com>
Tested-by: Dan Priamo <danp@adiengineering.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This patch adds the I2C controller driver for Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The structure cht_wc_i2c_adap_driver is local to the source
and does not need to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'cht_wc_i2c_adap_driver' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In addition to the base, low and high clock configuration, the AC timing
register #1 on the AST2400 houses fields controlling:
1. tBUF: Minimum delay between Stop and Start conditions
2. tHDSTA: Hold time for the Start condition
3. tACST: Setup time for Start and Stop conditions, and hold time for the
Repeated Start condition
These values are defined in hardware on the AST2500 and therefore don't
need to be set.
aspeed_i2c_init_clk() was performing a direct write of the generated
clock values rather than a read/mask/modify/update sequence to retain
tBUF, tHDSTA and tACST, and therefore cleared the tBUF, tHDSTA and tACST
fields on the AST2400. This resulted in a delay/setup/hold time of 1
base clock, which in some configurations is not enough for some devices
(e.g. the MAX31785 fan controller, with an APB of 48MHz and a desired
bus speed of 100kHz).
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sun, Yunying reported the following failure on Denverton micro-server:
EDAC DEBUG: pnd2_init:
EDAC DEBUG: pnd2_probe:
EDAC DEBUG: dnv_rd_reg: Read b_cr_tolud_pci=00000000_80000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_touud_lo_pci=00000000_80000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_touud_hi_pci=00000000_00000004
EDAC DEBUG: dnv_rd_reg: Read b_cr_asym_mem_region0_mchbar=00000000_00000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_asym_mem_region1_mchbar=00000000_00000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_mot_out_base_mchbar=00000000_00000000
EDAC DEBUG: dnv_rd_reg: Read b_cr_mot_out_mask_mchbar=00000000_00000000
EDAC pnd2: Failed to register device with error -19.
On Denverton micro-server, the presence of the P2SB bridge PCI device is
enabled or disabled by the item 'RelaxSecConf' in BIOS setup menu. When
'RelaxSecConf' is enabled, the P2SB PCI device is present and the pnd2_edac
EDAC driver also uses it to get BAR. Hiding the P2SB PCI device caused the
pnd2_edac EDAC driver failed to get BAR then reported the above failure.
Therefor, store the presence state of P2SB PCI device before unhiding it
for reading BAR and restore the presence state after reading BAR.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Reported-by: Yunying Sun <yunying.sun@intel.com>
Tested-by: Yunying Sun <yunying.sun@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There seems to be no need for separate ones since all users include both
files anyhow. Merge them because include/linux/i2c is to be deprecated.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c driver can run into driver dependency issues if its loaded
before a clock driver it depends on. Therefore, EPROBE_DEFER may be
returned by devm_clk_get and should be returned in probe to allow the
kernel to reprobe the driver at a later time. This patch allows the error
value returned by devm_clk_get to be passed through and not overwritten.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add i2c compatible for MT7622. Compare to MT8173 i2c controller,
MT7622 limits message numbers to 255, and does not support 4GB
DMA mode.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Cherry Trail Whiskey Cove PMIC's IRQ line is attached to one of
the GPIOs of the Cherry Trail SoC. The CHT GPIO controller sometimes
fails to deliver IRQs (seen when there is an IRQ storm on another pin).
This commit works around this by reducing the long timeout which was
a poor attempt to workaround this from 3s to 30ms and after that
manually checking the status register for transfer completion by
calling the threaded IRQ handler directly.
This is safe todo as the entire threaded IRQ handler is protected
by a mutex.
Note 30ms should be more then long enough, at 100KHz any smbus single
byte transaction should be finished in 4ms.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Testing has shown that writing 1 to clear the read-complete irq does
not work until the data register has been read first.
This commit fixes the driver to read the data register first, halving the
amount of interrupts in most cases since we mostly read on this i2c bus.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Although unlikely without locking the smbux_xfer function may miss
the nack flag and further fixes in this patch-set add some more
complex constructions which need protection.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C slave controller must be powered and active all the time when I2C
slave backend is registered in order to let master address and
communicate with us.
Now if the controller is runtime PM capable it will be suspended after
probe and cannot ever respond to the master or generate interrupts.
Fix this by resuming the controller when I2C slave backend is registered
and let it suspend after unregistering.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I guess pm_runtime_put_noidle() call in i2c_dw_probe_slave() was copied
by accident from similar master mode adapter registration code. It is
unbalanced due missing pm_runtime_get_noresume() but harmless since it
doesn't decrease dev->power.usage_count below zero.
In theory we can hit similar needless runtime suspend/resume cycle
during slave mode adapter registration that was happening when
registering the master mode adapter. See commit cd998ded5c ("i2c:
designware: Prevent runtime suspend during adapter registration").
However, since we are slave, we can consider it as a wrong configuration
if we have other slaves attached under this adapter and can omit the
pm_runtime_get_noresume()/pm_runtime_put_noidle() calls for simplicity.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Before I skipped null checks when the master is in the STOP state; this
fixes that.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: f327c686d3 ("i2c: aspeed: added driver for Aspeed I2C")
24xx BMCs have larger clock divider granularity which can cause problems
when trying to set them as 25xx clock dividers; this adds clock setting
code specific to 24xx.
This also fixes a potential issue where clock dividers were rounded down
instead of up.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-i2c@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use api pair of request_mem_region and release_mem_region
instead of release_resource.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Code sets bit DW_IC_CON_SPEED_FAST (0x4) always when configuring the slave
mode. This results incorrect register value DW_IC_CON_SPEED_HIGH (0x6)
when OR'ed together with DW_IC_CON_SPEED_STD (0x2).
Remove this and let the code set the speed mode bits according to clock
frequency or default to fast mode.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When i2c-designware is initialized in slave mode the
i2c-designware-slave.c: i2c_dw_irq_handler_slave() can hit a NULL
pointer dereference when I2C slave backend is not registered but code is
accessing the struct dw_i2c_dev.slave without testing is it NULL.
We might get spurious interrupts from other devices or from IRQ core
during unloading the driver when CONFIG_DEBUG_SHIRQ is set. Existing
check for enable and IRQ status is not enough since device can be power
gated and those bits may read 1.
Fix this by handling the interrupt only when also struct dw_i2c_dev.slave
is set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The commit 8503ff1665 ("i2c: designware: Avoid unnecessary resuming
during system suspend"), may suggest to the PM core to try out the so
called direct_complete path for system sleep. In this path, the PM core
treats a runtime suspended device as it's already in a proper low power
state for system sleep, which makes it skip calling the system sleep
callbacks for the device, except for the ->prepare() and the ->complete()
callbacks.
However, the PM core may unset the direct_complete flag for a parent
device, in case its child device are being system suspended before. In this
scenario, the PM core invokes the system sleep callbacks, no matter if the
device is runtime suspended or not.
Particularly in cases of an existing i2c slave device, the above path is
triggered, which breaks the assumption that the i2c device is always
runtime resumed whenever the dw_i2c_plat_suspend() is being called.
More precisely, dw_i2c_plat_suspend() calls clk_core_disable() and
clk_core_unprepare(), for an already disabled/unprepared clock, leading to
a splat in the log about clocks calls being wrongly balanced and breaking
system sleep.
To still allow the direct_complete path in cases when it's possible, but
also to keep the fix simple, let's runtime resume the i2c device in the
->suspend() callback, before continuing to put the device into low power
state.
Note, in cases when the i2c device is attached to the ACPI PM domain, this
problem doesn't occur, because ACPI's ->suspend() callback, assigned to
acpi_subsys_suspend(), already calls pm_runtime_resume() for the device.
It should also be noted that this change does not fix commit 8503ff1665
("i2c: designware: Avoid unnecessary resuming during system suspend").
Because for the non-ACPI case, the system sleep support was already broken
prior that point.
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Intel Cherry Trail Whiskey Cove PMIC does not contain a builtin
battery charger, instead boards with this PMIC use an external TI
bq24292i charger IC, which is connected to a SMBUS controller built into
the PMIC.
This commit adds an i2c-bus driver for the PMIC's builtin SMBUS
controller. The probe function for this i2c-bus will also register an
i2c-client for the TI bq24292i charger after the i2c-bus has been
registered.
Note that several device-properties are set on the client-device to
tell the bq24190 power-supply driver to integrate the Whiskey Cove PMIC
and e.g. use the PMIC's BC1.2 detection (through extcon) to determine
the maximum input current.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Support for the i2c controller on rv1108 soc.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When resuming, set up registers that have been lost in the sleep state.
Also, add clock handling in the resume / suspend hooks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When resuming, set up registers that have been lost in the sleep state.
Also, add clock handling in the resume / suspend hooks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Check for i2c_algorithm and i2c_adapter_quirks structures that are only
stored in the algo and quirks fields of an i2c_adapter structure
correspondingly. These fields are declared const, so i2c_algorithm and
i2c_adapter_quirks structures that have this property can be declared
as const also.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> (for designware)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow i2c-versatile to be enabled for ARM MPS platforms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Several drivers call to_platform_device() to get platform_device
and pass it to platform_get_drvdata(). In platform_get_drvdata(),
the platform_device is converted back to struct device again.
Use dev_get_drvdata() to avoid platform_device/device dance.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> (for DesignWare only)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The speed of sending i2c master code in high-speed mode depends on
source clock, clock-div and TIMING register. The source clock and
clock-div of different SoC are not all the same. In order to send
i2c master code at 400k in high-speed mode, a appropriate value
should be set to TIMING register for a certain source clock and
clock-div.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
At least the Acer Iconia Tab8 / aka W1-810 uses 1MiHz instead of
1MHz for one of its busses, fix this up to 1MHz instead of failing
the probe of that bus.
This fixes the accelerometer on the Acer Iconia Tab8 not working.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When we refuse to probe due to an invalid clock frequency, log
the frequency which is causing this error.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"This pull request contains:
- i2c core reorganization. One source file became too monolithic. It
is now split up, yet we still have the same named object as the
final output. This should ease maintenance.
- new drivers: ZTE ZX2967 family, ASPEED 24XX/25XX
- designware driver gained slave mode support
- xgene-slimpro driver gained ACPI support
- bigger overhaul for pca-platform driver
- the algo-bit module now supports messages with enforced STOP
- slightly bigger than usual set of driver updates and improvements
and with much appreciated quality assurance from Andy Shevchenko"
* 'i2c/for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (51 commits)
i2c: Provide a stub for i2c_detect_slave_mode()
i2c: designware: Let slave adapter support be optional
i2c: designware: Make HW init functions static
i2c: designware: fix spelling mistakes
i2c: pca-platform: propagate error from i2c_pca_add_numbered_bus
i2c: pca-platform: correctly set algo_data.reset_chip
i2c: acpi: Do not create i2c-clients for LNXVIDEO ACPI devices
i2c: designware: enable SLAVE in platform module
i2c: designware: add SLAVE mode functions
i2c: zx2967: drop COMPILE_TEST dependency
i2c: zx2967: always use the same device when printing errors
i2c: pca-platform: use dev_warn/dev_info instead of printk
i2c: pca-platform: use device managed allocations
i2c: pca-platform: add devicetree awareness
i2c: pca-platform: switch to struct gpio_desc
dt-bindings: add bindings for i2c-pca-platform
i2c: cadance: fix ctrl/addr reg write order
i2c: zx2967: add i2c controller driver for ZTE's zx2967 family
dt: bindings: add documentation for zx2967 family i2c controller
i2c: algo-bit: add support for I2C_M_STOP
...
Only certain system configurations may use the I2C slave mode so let the
support be optional. This allow reducing module size if needed:
text data bss dec hex filename
10328 1336 16 11680 2da0 drivers/i2c/busses/i2c-designware-core.ko
7222 1136 8 8366 20ae drivers/i2c/busses/i2c-designware-core.ko
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Luis Oliveira <lolivei@synopsys.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Recent i2c-designware slave support patches use master or slave HW init
functions through the function pointer so we can declare them static.
While at it, rename i2c_dw_init() as i2c_dw_init_master().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Luis Oliveira <lolivei@synopsys.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Trivial fixes to spelling mistakes in dev_dbg message
"STAUTS" -> "STATUS"
"SLAVE_ACTTVITY" -> "SLAVE_ACTIVITY"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rather than returning -ENODEV if i2c_pca_add_numbered_bus() fails,
propagate the error to aid debugging.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When device tree support was added the setting of algo_data.reset_chip
was moved. There were two problems with this. The first being that
i2c_pca_pf_resetchip was only used if platform data was provided. The
second that it was unconditionally overridden with
i2c_pca_pf_dummyreset. Ensure that however the reset gpio is defined the
correct reset_chip function is used.
Fixes: commit 4cc7229daa ("i2c: pca-platform: switch to struct gpio_desc")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Slave mode selected in platform module if the support is detected in
the DT.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Changes in Kconfig to enable I2C_DESIGNWARE_SLAVE support
- Slave functions added to core library file
- Slave abort sources added to common source file
- New driver: i2c-designware-slave added
- Changes in the Makefile to compile the I2C_DESIGNWARE_SLAVE module
when supported by the architecture.
All the SLAVE flow is added but it is not enabled via platform
driver.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: made a function static and one-lined a message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
0-DAY kernel test reports the following build issue on IA64 architecture
with allmodconfig.
drivers/i2c/busses/i2c-zx2967.c: In function 'zx2967_i2c_writesb':
>> drivers/i2c/busses/i2c-zx2967.c:87:2: error: implicit declaration of function 'writesb' [-Werror=implicit-function-declaration]
writesb(i2c->reg_base + reg, data, len);
^~~~~~~
drivers/i2c/busses/i2c-zx2967.c: In function 'zx2967_i2c_readsb':
>> drivers/i2c/busses/i2c-zx2967.c:93:2: error: implicit declaration of function 'readsb' [-Werror=implicit-function-declaration]
readsb(i2c->reg_base + reg, data, len);
^~~~~~
cc1: some warnings being treated as errors
It's caused by that writesb/readsb are unavailable on IA64 architecture.
Let's drop COMPILE_TEST dependency to avoid the build issue.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Let's always use the platform device for dev_* and not sometimes the
adapter device as well. Also fix this checkpatch check:
CHECK: Macro argument 'i2c' may be better as '(i2c)' to avoid precedence issues
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch to using the devm_ APIs and remove the now unnecessary error
handling and most of the device removal code.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[wsa: adapted error handling I added in previous patch]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow devices that use this driver to be registered via a
devicetree.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[wsa: fixed leakage when registering GPIO failed]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make use of struct gpio_desc which allows us to specify the active state
of the reset pin.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver was clearing the hold bit in the control register before
writing to the address register which resulted in a stop condition
being generated rather than a repeated start.
This issue was only observed when a system was running much
slower than a normal processor would execute. The IP data sheet
mentions a ordering of writing to the address register before
clearing the hold.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Paresh Chaudhary <paresh.chaudhary@rockwellcollins.com>
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds i2c controller driver for ZTE's zx2967 family.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Added slave support for Aspeed I2C controller. Supports fourteen busses
present in AST24XX and AST25XX BMC SoCs by Aspeed.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Added initial master support for Aspeed I2C controller. Supports
fourteen busses present in AST24XX and AST25XX BMC SoCs by Aspeed.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add recent findings (IGNORE_NAK) and document in a bit more detail why
the feature is not possible.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-imx driver incorrectly uses readb()/writeb() to read and
write to the appropriate registers when performing a repeated start.
The appropriate imx_i2c_read_reg()/imx_i2c_write_reg() functions
should be used instead. Performing a repeated start results in
a kernel panic. The platform is imx.
Signed-off-by: Michail G Etairidis <m.etairidis@beck-ipc.com>
Fixes: ce1a78840f ("i2c: imx: add DMA support for freescale i2c driver")
Fixes: 054b62d9f2 ("i2c: imx: fix the i2c bus hang issue when do repeat restart")
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Definitions were added to core library
- A example was added to designware-core.txt Documentation that shows
how the slave can be setup using DTS
SLAVE related definitions were added to the core of the controller.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- The functions related to I2C master mode of operation were transformed
in a single driver.
- Common definitions were moved to i2c-designware-core.h
- The i2c-designware-core is now only a library file, the functions
associated are in a source file called i2c-designware-common and
are used by both i2c-designware-master and i2c-designware-slave.
- To decrease noise in namespace common i2c_dw_*() functions are
now using ops to keep them private.
- Designware PCI driver had to be changed to match the previous ops
functions implementation.
Almost all of the "core" source is now part of the "master" source. The
difference is the functions used by both modes and they are in the
"common" source file.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Factor out all _master() part of code from i2c-designware-core
and i2c-designware-platdrv to separate functions.
- Standardize all code related with MASTER mode.
- I have to take off DW_IC_INTR_TX_EMPTY from DW_IC_INTR_DEFAULT_MASK
because it is master specific.
The purpose of this is to prepare the controller to have is I2C MASTER
flow in a separate driver. To do this first all the
functions/definitions related to the MASTER flow were identified.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The purpose of this commit is to fix some comments and styling in the
existing code due to the need of reuse this code. What is being made
here is:
- Sorted the headers files
- Corrected some comments style (capital letters, lowcase i2c)
- Reverse tree in the variables declaration
- Add/remove empty lines and tabs where needed
- Fix of misspelled word "endianness" and "transferred"
- Replaced the return variable "r" with the more standard "ret"
The value of this, besides the rules of coding style, is because I
will use this code after and it will make my future patch a lot bigger and
complicated to review. The work here won't bring any additional work to
backported fixes because is just style and reordering.
Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Replace '%d' by '%zu' to fix the following type of compilation warnings:
drivers/i2c/busses/i2c-at91.c:277:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 5 has type ‘size_t’ [-Wformat=]
dev_dbg(dev->dev, "wrote 0x%x, to go %d\n", *dev->buf, dev->buf_len);
^
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Tested-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
clk_prepare_enable() can fail here and we must check its return value.
Also, add a missing clk_disable_unprepare().
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It is 'R-Car', not 'RCar'. No code or binding changes, only descriptive text.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Set I2C_CLASS_HWMON for xlp9xx to enable automatic probing of BMC
devices by the ipmi-ssif driver.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Added SMBUS PCI Ids for SMBUS for Cannon Lake PCH.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[jarkko.nikula@linux.intel.com: Add entries to Documentation and Kconfig.
Cover Cannon Lake-H too]
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The newly added support for the pcc mailbox fails to build
in some configurations:
drivers/i2c/busses/i2c-xgene-slimpro.c: In function 'xgene_slimpro_i2c_probe':
drivers/i2c/busses/i2c-xgene-slimpro.c:516:25: error: implicit declaration of function 'memremap'; did you mean 'memcmp'? [-Werror=implicit-function-declaration]
drivers/i2c/busses/i2c-xgene-slimpro.c:518:13: error: 'MEMREMAP_WB' undeclared (first use in this function)
drivers/i2c/busses/i2c-xgene-slimpro.c:518:13: note: each undeclared identifier is reported only once for each function it appears in
This includes the missing header file.
Fixes: df5da47fe7 ("i2c: xgene-slimpro: Add ACPI support by using PCC mailbox")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Because we need to transfer some bytes with PIO, the msg length is not
the length of the DMA buffer. Use the correct value which we used when
doing the mapping.
Fixes: 73e8b05283 ("i2c: rcar: add DMA support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instead of printing errors after mxs_i2c_pio_wait_xfer_end returns with
an error code just print a debug message.
NAKs and timeouts can occur in this situation normally, so do not treat
them as errors.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After removal of platform_data support, we can simplify OF handling.
of_match_device() evaluates to NULL if !CONFIG_OF or if there is no node
pointer for that device, so we can remove the check for the node ptr.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No platform currently upstream makes use of this platform_data anymore.
The ones that did are converted to DT meanwhile. So, remove it. The old
platforms likely don't have the 'clks_per_cnt' feature, otherwise it
would have been implemented by now. And in the unlikely case they need
to setup a different bus speed, we should rather go for a generic i2c
platform data just for that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds ACPI support by using PCC mailbox communication
interface.
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch refactors the code to use a single message function to
send command message.
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C core became quite huge and its monolithic structure makes
maintenance hard. So, prepare to break out some functionality into
separate files by renaming the source file. Note that we keep the
resulting object name constant to avoid regressions.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We need to initializes those variables to 0 for platforms that do not
provide ACPI parameters. Otherwise, we set sda_hold_time to random
values, breaking e.g. Galileo and IOT2000 boards.
Fixes: 9d64084330 ("i2c: designware: don't infer timings described by ACPI from clock rate")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit bd698d24b1 ("i2c: designware: Get selected speed mode
sda-hold-time via ACPI") updated the logic that reads the timing
parameters for various I2C bus rates from the DSDT, to only read
the timing parameters for the currently selected mode.
This causes a WARN_ON() splat on platforms that legally omit the clock
frequency from the ACPI description, because in the new situation, the
core I2C designware driver still accesses the fields in the driver
struct that we no longer populate, and proceeds to calculate them from
the clock frequency. Since the clock frequency is unspecified, the
driver complains loudly using a WARN_ON().
So revert back to the old situation, where the struct fields for all
timings are populated, but retain the new logic which chooses the SDA
hold time from the timing mode that is currently in use.
Fixes: bd698d24b1 ("i2c: designware: Get selected speed mode ...")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With ACPI, i2c-core requires ACPI companion to be set in order for it
to create slave device.
This patch sets the ACPI companion accordingly.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no reason to use platform_get_irq() for non-DT probing and
irq_of_parse_and_map() for DT probing. Indeed, platform_get_irq()
works fine for both.
In addition, using platform_get_irq() properly returns -EPROBE_DEFER
when the interrupt controller is not yet available, so instead of
inventing our own error code (-ENXIO), return the one provided by
platform_get_irq().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
- Update the ACPICA code in the kernel to upstream revision
20170303 which includes:
* Minor fixes and improvements in the core code (Bob Moore,
Seunghun Han).
* Debugger fixes (Colin Ian King, Lv Zheng).
* Compiler/disassembler improvements (Bob Moore, David Box,
Lv Zheng).
* Build-related update (Lv Zheng).
- Add new device IDs and platform-related information to the
ACPI drivers for Intel (LPSS) and AMD (APD) SoCs (Hanjun Guo,
Hans de Goede).
- Make it possible to quirk ACPI-enumerated devices as "always
present" on platforms where they are incorrectly reported as not
present by the AML and add the INT0002 device ID to the list of
"always present" devices (Hans de Goede).
- Fix the register information in the xpower PMIC driver and add
comments to map the registers to symbols used by AML to it
(Hans de Goede).
- Move the code turning off unused ACPI power resources during
system resume to a point after all devices have been resumed
to avoid issues with power resources that do not behave as
expected (Hans de Goede).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJZEkXjAAoJEILEb/54YlRxWQ4QAIymQKPRXS6g8/5qZ8w5YNY+
gLHkEzANPW3JHTUwv2hxfPP4AWYnDwTSg5g3RVue0R+tj49ERNsDoaFXBJ8L3wlA
bLr9VFXPtzX5yuFD1MGeDWeUqGwuTJztWcMAkzpRgbj+6ppjJForObM76XFB3Pmn
t5XUs0Tjlahqhg59GCHkt+kGeL5BOayLvIQt17IxQiAzAi3SY4P/qcq6qG2hY7BX
0PB/zodPfCQpbcReKMDGfQlhxSWgcoQiCoBmmx0YIQfTQzmvWUejek1GcSUfJu1C
Hx/ndBiAWkJ7m77LMAyQT9FgRsp9GkDllYhXJ+rmAWFuqNrEpTFJjY6q3wXxMyMl
T39BWPFfauatEmDYXXLWpUuFaxX+VJ5nNlUtHGDm3xP/NI4ARiAUowk6haFfR1nx
YmBon4VPzG2cf6wnXKI2rdWIbkKLkDYLPpzBpvUxswkPNtEF2/272nPwo0nqfTms
S3ddyRhYBnht1JgDPf/nAyUOK0jowxWlFEBsKvLUZ0faHuIhAS4FEO8DNxVnhP0b
m1nlZFctJeRCcI11mva5Tob9w8w5Z7WslfoTLQ9eFBl6RJdmy05s8d/CQYI9hK15
EmVIRRqJ+G4gNHdcV26+JKBWgrJv6WSmf32QBXDCT94C4iZrqxXmccvY7s2tZEJR
7VEo/7Ck70xbNcvEOn3c
=Ytsi
-----END PGP SIGNATURE-----
Merge tag 'acpi-extra-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20170303 which adds a few minor fixes and improvements, update ACPI
SoC drivers with new device IDs, platform-related information and
similar, fix the register information in the xpower PMIC driver,
introduce a concept of "always present" devices to the ACPI device
enumeration code and use it to fix a problem with one platform, and
fix a system resume issue related to power resources.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20170303
which includes:
* Minor fixes and improvements in the core code (Bob Moore,
Seunghun Han).
* Debugger fixes (Colin Ian King, Lv Zheng).
* Compiler/disassembler improvements (Bob Moore, David Box, Lv
Zheng).
* Build-related update (Lv Zheng).
- Add new device IDs and platform-related information to the ACPI
drivers for Intel (LPSS) and AMD (APD) SoCs (Hanjun Guo, Hans de
Goede).
- Make it possible to quirk ACPI-enumerated devices as "always
present" on platforms where they are incorrectly reported as not
present by the AML and add the INT0002 device ID to the list of
"always present" devices (Hans de Goede).
- Fix the register information in the xpower PMIC driver and add
comments to map the registers to symbols used by AML to it (Hans de
Goede).
- Move the code turning off unused ACPI power resources during system
resume to a point after all devices have been resumed to avoid
issues with power resources that do not behave as expected (Hans de
Goede)"
* tag 'acpi-extra-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (22 commits)
ACPI / power: Delay turning off unused power resources after suspend
ACPI / PMIC: xpower: Fix power_table addresses
ACPI / LPSS: Call pwm_add_table() for Bay Trail PWM device
ACPICA: Update version to 20170303
ACPICA: iasl: add ASL conversion tool
ACPICA: Local cache support: Allow small cache objects
ACPICA: Disassembler: Do not unconditionally remove temporary names
ACPICA: iasl: Fix IORT SMMU GSI disassembling
ACPICA: Cleanup AML opcode definitions, no functional change
ACPICA: Debugger: Add interpreter blocking mark for single-step mode
ACPICA: debugger: fix memory leak on Pathname
ACPICA: Update for automatic repair code for objects returned by evaluate_object
ACPICA: Namespace: fix operand cache leak
ACPICA: Fix several incorrect invocations of ACPICA return macro
ACPICA: Fix a module for excessive debug output
ACPICA: Update some function headers, no funtional change
ACPICA: Disassembler: Enhance resource descriptor detection
i2c: designware: Add ACPI HID for Hisilicon Hip07/08 I2C controller
ACPI / APD: Add clock frequency for Hisilicon Hip07/08 I2C controller
ACPI / bus: Add INT0002 to list of always-present devices
...
Add ACPI HID HISI02A1 and HISI02A2 for Hisilicon Hip07/08,
which have different clock frequency.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Set I2C_CLASS_HWMON to enable automatic probing of BMC devices
by the ipmi-ssif driver.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
PM handling is correct but might be a bit subtle. Add some comments for
clarification.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Resume failed because of uninitialized registers. Instead of adding a
resume callback, we simply initialize registers before every transfer.
This lightweight change is more robust and will keep us safe if we ever
need support for power domains or dynamic frequency changes.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
trivial fix to spelling mistake in MODULE_DESCRIPTION text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Driver core provides of_device_get_match_data which can be used
to get driver data instead of custom helper.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of clock setup error it is enough to log it once.
Moreover patch simplifies clock setup routines.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no need to keep separate settings for high and fast speed clock.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Instead of using cryptic loop direct calculation of timings
can be used.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/i2c/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jean Delvare <jdelvare@suse.de>
cc: linux-i2c@vger.kernel.org
