Cleanup the formatting of comments, remove some which don't make sense
anymore.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[fix conflict with 96a608a4]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
During iw_nes initialization the link status for SFP+ PHY is always
detected as "up" regardless of real state (cable either connected or
disconnected). Add SFP+ PHY specific link status detection to the
iw_nes initialization procedure. Use link status recheck for
netdev_open to detect delayed state updates.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In case of SFP+ PHY, link status check at interrupt processing can
give false results. For proper link status change detection a delayed
recheck is needed to give nes registers time to settle. Add a
periodic link status recheck scheduled at interrupt to detect
potential delayed registers state changes.
Addresses: http://bugs.openfabrics.org/bugzilla/show_bug.cgi?id=2117
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Depending on link state change, IB_EVENT_PORT_ERR or
IB_EVENT_PORT_ACTIVE should be generated when handling MAC interrupts.
Plugging in a cable happens to result in series of interrupts changing
driver's link state a number of times before finally staying at link
up (e.g. link up, link down, link up, link down, ..., link up). To
prevent sending series of redundant IB_EVENT_PORT_ACTIVE and
IB_EVENT_PORT_ERR events, we use a timer to debounce them in
nes_port_ibevent().
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable configuring bonds on nes devices by adding missing support for
master net_device to the driver.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes the following kconfig error after changing
CONFIGFS_FS -> select SYSFS:
fs/sysfs/Kconfig:1:error: recursive dependency detected!
fs/sysfs/Kconfig:1: symbol SYSFS is selected by CONFIGFS_FS
fs/configfs/Kconfig:1: symbol CONFIGFS_FS is selected by NETCONSOLE_DYNAMIC
drivers/net/Kconfig:3390: symbol NETCONSOLE_DYNAMIC depends on SYSFS
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: James Bottomley <James.Bottomley@suse.de>
Commit 415e12b237 ("PCI/ACPI: Request _OSC control once for each root
bridge (v3)") put the acpi_hest_init() call in acpi_pci_root_init() into
a wrong place, presumably because the author confused acpi_pci_disabled
with acpi_disabled. Bring the code ordering in acpi_pci_root_init()
back to sanity.
Additionally, make sure that hest_disable is set when acpi_disabled is
set, which is going to prevent acpi_hest_parse(), that still may be
executed for acpi_disabled=1 through aer_acpi_firmware_first(), from
crashing because of uninitialized hest_tab.
Reported-and-tested-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (23 commits)
sanitize vfsmount refcounting changes
fix old umount_tree() breakage
autofs4: Merge the remaining dentry ops tables
Unexport do_add_mount() and add in follow_automount(), not ->d_automount()
Allow d_manage() to be used in RCU-walk mode
Remove a further kludge from __do_follow_link()
autofs4: Bump version
autofs4: Add v4 pseudo direct mount support
autofs4: Fix wait validation
autofs4: Clean up autofs4_free_ino()
autofs4: Clean up dentry operations
autofs4: Clean up inode operations
autofs4: Remove unused code
autofs4: Add d_manage() dentry operation
autofs4: Add d_automount() dentry operation
Remove the automount through follow_link() kludge code from pathwalk
CIFS: Use d_automount() rather than abusing follow_link()
NFS: Use d_automount() rather than abusing follow_link()
AFS: Use d_automount() rather than abusing follow_link()
Add an AT_NO_AUTOMOUNT flag to suppress terminal automount
...
Instead of splitting refcount between (per-cpu) mnt_count
and (SMP-only) mnt_longrefs, make all references contribute
to mnt_count again and keep track of how many are longterm
ones.
Accounting rules for longterm count:
* 1 for each fs_struct.root.mnt
* 1 for each fs_struct.pwd.mnt
* 1 for having non-NULL ->mnt_ns
* decrement to 0 happens only under vfsmount lock exclusive
That allows nice common case for mntput() - since we can't drop the
final reference until after mnt_longterm has reached 0 due to the rules
above, mntput() can grab vfsmount lock shared and check mnt_longterm.
If it turns out to be non-zero (which is the common case), we know
that this is not the final mntput() and can just blindly decrement
percpu mnt_count. Otherwise we grab vfsmount lock exclusive and
do usual decrement-and-check of percpu mnt_count.
For fs_struct.c we have mnt_make_longterm() and mnt_make_shortterm();
namespace.c uses the latter in places where we don't already hold
vfsmount lock exclusive and opencodes a few remaining spots where
we need to manipulate mnt_longterm.
Note that we mostly revert the code outside of fs/namespace.c back
to what we used to have; in particular, normal code doesn't need
to care about two kinds of references, etc. And we get to keep
the optimization Nick's variant had bought us...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In case of single tx and rx queues, three MSI-x vectors are allocated instead
of two. This patch fixes that.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access to cmd register is racey, especially in smp environments. Protect
it using a spinlock.
Signed-off-by: Matthieu Bucchianeri <matthieu@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a small possibility of a race where the suspend routine gets
called, while a napi callback is still pending and when that comes up,
it enables interrupts which just got disabled in the suspend routine.
This change adds napi disable call in suspend and enable in resume to
avoid race.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Show per-queue stats in ethtool -S output for vmxnet3 interface. Register dump
of ethtool should dump registers for all tx and rx queues.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a performance enhancement fix. vmxnet3 device performs better when
provided with at least 54 bytes (ethernet 14 + IP 20+ TCP 20) in the first SG
buffer. For UDP packets driver provides lesser than that in first sg. This
change fixes the same. Also avoid the redundant pskb_may_pull() call.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make hw vlan tag stripping as enabled by default. Thereby remove
the code to conditionally enable it later.
Signed-off-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While activating the device get it's MAC address from netdev. This will allow
the MAC address configured using ifconfig to persist through the reset.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug while changing ring size when MTU is changed.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The physical address is never used by the device tree code when
allocating memory for unflattening. Change the architecture's alloc
hook to return the virutal address instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some OSA level have a bug in the hw tx csum logic. We can circumvent
this bug by turning on IP hw csum also.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The open function of qeth is not executed if the qeth device is in
state DOWN or HARDSETUP. A recovery switches from state SOFTSETUP to
HARDSETUP to DOWN to HARDSETUP and back to SOFTSETUP. If open and
recover are running concurrently, open fails if it hits the states
HARDSETUP or DOWN. This patch inserts waiting for recovery finish
in the qeth open functions to enable successful qeth device opening
in spite of a running recovery.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dentry op (d_manage) to permit a filesystem to hold a process and make it
sleep when it tries to transit away from one of that filesystem's directories
during a pathwalk. The operation is keyed off a new dentry flag
(DCACHE_MANAGE_TRANSIT).
The filesystem is allowed to be selective about which processes it holds and
which it permits to continue on or prohibits from transiting from each flagged
directory. This will allow autofs to hold up client processes whilst letting
its userspace daemon through to maintain the directory or the stuff behind it
or mounted upon it.
The ->d_manage() dentry operation:
int (*d_manage)(struct path *path, bool mounting_here);
takes a pointer to the directory about to be transited away from and a flag
indicating whether the transit is undertaken by do_add_mount() or
do_move_mount() skipping through a pile of filesystems mounted on a mountpoint.
It should return 0 if successful and to let the process continue on its way;
-EISDIR to prohibit the caller from skipping to overmounted filesystems or
automounting, and to use this directory; or some other error code to return to
the user.
->d_manage() is called with namespace_sem writelocked if mounting_here is true
and no other locks held, so it may sleep. However, if mounting_here is true,
it may not initiate or wait for a mount or unmount upon the parameter
directory, even if the act is actually performed by userspace.
Within fs/namei.c, follow_managed() is extended to check with d_manage() first
on each managed directory, before transiting away from it or attempting to
automount upon it.
follow_down() is renamed follow_down_one() and should only be used where the
filesystem deliberately intends to avoid management steps (e.g. autofs).
A new follow_down() is added that incorporates the loop done by all other
callers of follow_down() (do_add/move_mount(), autofs and NFSD; whilst AFS, NFS
and CIFS do use it, their use is removed by converting them to use
d_automount()). The new follow_down() calls d_manage() as appropriate. It
also takes an extra parameter to indicate if it is being called from mount code
(with namespace_sem writelocked) which it passes to d_manage(). follow_down()
ignores automount points so that it can be used to mount on them.
__follow_mount_rcu() is made to abort rcu-walk mode if it hits a directory with
DCACHE_MANAGE_TRANSIT set on the basis that we're probably going to have to
sleep. It would be possible to enter d_manage() in rcu-walk mode too, and have
that determine whether to abort or not itself. That would allow the autofs
daemon to continue on in rcu-walk mode.
Note that DCACHE_MANAGE_TRANSIT on a directory should be cleared when it isn't
required as every tranist from that directory will cause d_manage() to be
invoked. It can always be set again when necessary.
==========================
WHAT THIS MEANS FOR AUTOFS
==========================
Autofs currently uses the lookup() inode op and the d_revalidate() dentry op to
trigger the automounting of indirect mounts, and both of these can be called
with i_mutex held.
autofs knows that the i_mutex will be held by the caller in lookup(), and so
can drop it before invoking the daemon - but this isn't so for d_revalidate(),
since the lock is only held on _some_ of the code paths that call it. This
means that autofs can't risk dropping i_mutex from its d_revalidate() function
before it calls the daemon.
The bug could manifest itself as, for example, a process that's trying to
validate an automount dentry that gets made to wait because that dentry is
expired and needs cleaning up:
mkdir S ffffffff8014e05a 0 32580 24956
Call Trace:
[<ffffffff885371fd>] :autofs4:autofs4_wait+0x674/0x897
[<ffffffff80127f7d>] avc_has_perm+0x46/0x58
[<ffffffff8009fdcf>] autoremove_wake_function+0x0/0x2e
[<ffffffff88537be6>] :autofs4:autofs4_expire_wait+0x41/0x6b
[<ffffffff88535cfc>] :autofs4:autofs4_revalidate+0x91/0x149
[<ffffffff80036d96>] __lookup_hash+0xa0/0x12f
[<ffffffff80057a2f>] lookup_create+0x46/0x80
[<ffffffff800e6e31>] sys_mkdirat+0x56/0xe4
versus the automount daemon which wants to remove that dentry, but can't
because the normal process is holding the i_mutex lock:
automount D ffffffff8014e05a 0 32581 1 32561
Call Trace:
[<ffffffff80063c3f>] __mutex_lock_slowpath+0x60/0x9b
[<ffffffff8000ccf1>] do_path_lookup+0x2ca/0x2f1
[<ffffffff80063c89>] .text.lock.mutex+0xf/0x14
[<ffffffff800e6d55>] do_rmdir+0x77/0xde
[<ffffffff8005d229>] tracesys+0x71/0xe0
[<ffffffff8005d28d>] tracesys+0xd5/0xe0
which means that the system is deadlocked.
This patch allows autofs to hold up normal processes whilst the daemon goes
ahead and does things to the dentry tree behind the automouter point without
risking a deadlock as almost no locks are held in d_manage() and none in
d_automount().
Signed-off-by: David Howells <dhowells@redhat.com>
Was-Acked-by: Ian Kent <raven@themaw.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: avoid pointless blocked-task warnings
rcu: demote SRCU_SYNCHRONIZE_DELAY from kernel-parameter status
rtmutex: Fix comment about why new_owner can be NULL in wake_futex_pi()
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, olpc: Add missing Kconfig dependencies
x86, mrst: Set correct APB timer IRQ affinity for secondary cpu
x86: tsc: Fix calibration refinement conditionals to avoid divide by zero
x86, ia64, acpi: Clean up x86-ism in drivers/acpi/numa.c
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timekeeping: Make local variables static
time: Rename misnamed minsec argument of clocks_calc_mult_shift()
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Remove syscall_exit_fields
tracing: Only process module tracepoints once
perf record: Add "nodelay" mode, disabled by default
perf sched: Fix list of events, dropping unsupported ':r' modifier
Revert "perf tools: Emit clearer message for sys_perf_event_open ENOENT return"
perf top: Fix annotate segv
perf evsel: Fix order of event list deletion
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: fix missing branch in __error_a
ARM: fix /proc/$PID/stack on SMP
ARM: Fix build regression on SA11x0, PXA, and H720x targets
ARM: 6625/1: use memblock memory regions for "System RAM" I/O resources
ARM: fix wrongly patched constants
ARM: 6624/1: fix dependency for CONFIG_SMP_ON_UP
ARM: 6623/1: Thumb-2: Fix out-of-range offset for Thumb-2 in proc-v7.S
ARM: 6622/1: fix dma_unmap_sg() documentation
ARM: 6621/1: bitops: remove condition code clobber for CLZ
ARM: 6620/1: Change misleading warning when CONFIG_CMDLINE_FORCE is used
ARM: 6619/1: nommu: avoid mapping vectors page when !CONFIG_MMU
ARM: sched_clock: make minsec argument to clocks_calc_mult_shift() zero
ARM: sched_clock: allow init_sched_clock() to be called early
ARM: integrator: fix compile warning in cpu.c
ARM: 6616/1: Fix ep93xx-fb init/exit annotations
ARM: twd: fix display of twd frequency
ARM: udelay: prevent math rounding resulting in short udelays
Commit f5e70d0fe3 renamed MD_RAID6_PQ to RAID6_PQ,
but iop-adma.c didn't update synchronously.
Signed-off-by: Wei Yongquan <weiyqlq@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We were reading channel status then taking a lock. This lead to a race because
this lock may delay us and then make this channel not idle anymore.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Place flags on first descriptor of chain instead of last.
This is the one used by atc_chain_complete() function while unmapping.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use subsys_initcall instead of module_init in order to keep DMA engine rolling
before other peripheral drivers.
Signed-off-by: Eric Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Following descriptor flow in at_hdmac driver, descriptor comming from
atc_desc_get() as already DMA_CTRL_ACK flag set. No need to set it again.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In atc_prep_slave_sg() function we use dma_address field of scatterlist with
sg_dma_address() macro instead of sg_phys(). DMA address is already computed
by dma_map_sg() or another mapping function in calling driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Support new device OKI SEMICONDUCTOR's ML7213 IOH(Input/Output Hub) which is for
IVI(In-Vehicle Infotainment) use.
The ML7213 is companion chip for Intel Atom E6xx series.
The ML7213 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This reverts commit dfe63bb0ad.
This commit was causing nouveau not to work properly, for -rc1 I'd
prefer it worked and we can look if this is useful for 2.6.39.
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi/amba-pl022: fixing compilation warning.
spi: Enable SPI driver for S5P6440 and S5P6450
mmc: sdhci-of: fix build on non-powerpc platforms
spi/imx: Add i.MX53 support
spi/dw_spi: don't treat NULL clk as an error
spi: tegra: don't treat NULL clk as an error
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Encourage move to dev_pm_ops by warning on use of legacy methods
i2c: Factor out runtime suspend checks from PM operations
i2c: Unregister dummy devices last on adapter removal
clk_freq is used uninitialized in pl022_setup routine. This patch
fix compilation warning for using uninitialized variable
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: restore multiple bd_link_disk_holder() support
block cfq: compensate preempted queue even if it has no slice assigned
block cfq: make queue preempt work for queues from different workload
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
GRETH: resolve SMP issues and other problems
GRETH: handle frame error interrupts
GRETH: avoid writing bad speed/duplex when setting transfer mode
GRETH: fixed skb buffer memory leak on frame errors
GRETH: GBit transmit descriptor handling optimization
GRETH: fix opening/closing
GRETH: added raw AMBA vendor/device number to match against.
cassini: Fix build bustage on x86.
e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs
e1000e: update Copyright for 2011
e1000: Avoid unhandled IRQ
r8169: keep firmware in memory.
netdev: tilepro: Use is_unicast_ether_addr helper
etherdevice.h: Add is_unicast_ether_addr function
ks8695net: Use default implementation of ethtool_ops::get_link
ks8695net: Disable non-working ethtool operations
USB CDC NCM: Don't deref NULL in cdc_ncm_rx_fixup() and don't use uninitialized variable.
vxge: Remember to release firmware after upgrading firmware
netdev: bfin_mac: Remove is_multicast_ether_addr use in netdev_for_each_mc_addr
ipsec: update MAX_AH_AUTH_LEN to support sha512
...
Since the PM core wishes to transition away from the legacy suspend
and resume methods and since removing them makes using PM core features
like runtime PM much easier start warning when a driver is registered
using the legacy methods.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When devices use dev_pm_ops the I2C API is implementing standard functionality
for integration with runtime PM and for checking for the presence of a per
device op. The PM core provides pm_generic_ functions implementing this
behaviour - use them to reduce coupling with future PM updates.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove real devices first and dummy devices last. This gives device
driver which instantiated dummy devices themselves a chance to clean
them up before we do.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: stable@kernel.org
Fixes the following:
1. POLL should not enable IRQ when work is not completed
2. No locking between TX descriptor cleaning and XMIT descriptor handling
3. No locking between RX POLL and XMIT modifying control register
4. Since TX cleaning (called from POLL) is running in parallel with XMIT
unnecessary locking is needed.
5. IRQ handler looks at RX frame status solely, this is wrong when IRQ is
temporarily disabled (in POLL), and when IRQ is shared.
6. IRQ handler clears IRQ status, which is unnecessary
7. TX queue was stopped in preventing cause when not MAX_SKB_FRAGS+1
descriptors were available after a SKB been scheduled by XMIT. Instead
the TX queue is stopped first when not enough descriptors are available
upon entering XMIT.
It was hard to split up this patch in smaller pieces since all are tied
together somehow.
Note the RX flag used in the interrupt handler does not signal that
interrupt was asserted, but that a frame was received. Same goes for TX.
Also, IRQ is not asserted when the RX flag is set before enabling IRQ
enable until a new frame is received. So extra care must be taken to
avoid enabling IRQ and all descriptors are already used, hence dead lock
will upon us. See new POLL implementation that enableds IRQ then look at
the RX flag to determine if one or more IRQs may have been missed. TX/RX
flags are cleared before handling previously enabled descriptors, this
ensures that the RX/TX flags are valid when determining if IRQ should be
turned on again.
By moving TX cleaning from POLL to XMIT in the standard case, removes some
locking trouble. Enabling TX cleaning from poll only when not enough TX
descriptors are available is safe because the TX queue is at the same time
stopped, thus XMIT will not be called. The TX queue is woken up again when
enough descriptrs are available.
TX Frames are always enabled with IRQ, however the TX IRQ Enable flag will
not be enabled until XMIT must wait for free descriptors.
Locking RX and XMIT parts of the driver from each other is needed because
the RX/TX enable bits share the same register.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frame error interrupts must also be handled since the RX flag only indicates
successful reception, it is unlikely but the old code may lead to dead lock
if 128 error frames are recieved in a row.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new SKB buffer should not be allocated when the old SKB is reused.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is safe to enable all fragments before enabling the first descriptor,
this way all descriptors don't have to be processed twice, added extra
memory barrier.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NAPI is disabled there is no point in having IRQs enabled, TX/RX
should be off before clearing the TX/RX descriptor rings.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately, not all CONFIG_OF platforms provide
pci_device_to_OF_node().
Change the test to CONFIG_SPARC for now to deal with
the build regressions.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915/lvds: Add AOpen i915GMm-HFS to the list of false-positive LVDS
agp/intel: Fix device names of i845 and 845G
drm/i915: Disable GPU semaphores on SandyBridge mobile
drm/i915/execbuffer: Clear domains before beginning reloc processing
drm/i915/execbuffer: Reorder relocations to match new object order
drm/i915: Fix error handler to capture the first batch after the seqno
drm/i915: Add a module option to override the use of SSC
drm/i915/panel: The backlight is enabled if the current value is non-zero
drm/i915/debugfs: Correct format after changing type of err object 'size'
Commit e09b457b (block: simplify holder symlink handling) incorrectly
assumed that there is only one link at maximum. dm may use multiple
links and expects block layer to track reference count for each link,
which is different from and unrelated to the exclusive device holder
identified by @holder when the device is opened.
Remove the single holder assumption and automatic removal of the link
and revive the per-link reference count tracking. The code
essentially behaves the same as before commit e09b457b sans the
unnecessary kobject reference count dancing.
While at it, note that this facility should not be used by anyone else
than the current ones. Sysfs symlinks shouldn't be abused like this
and the whole thing doesn't belong in the block layer at all.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Milan Broz <mbroz@redhat.com>
Cc: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Neil Brown <neilb@suse.de>
Cc: linux-raid@vger.kernel.org
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI/PM: Report wakeup events before resuming devices
PCI/PM: Use pm_wakeup_event() directly for reporting wakeup events
PCI: sysfs: Update ROM to include default owner write access
x86/PCI: make Broadcom CNB20LE driver EMBEDDED and EXPERIMENTAL
x86/PCI: don't use native Broadcom CNB20LE driver when ACPI is available
PCI/ACPI: Request _OSC control once for each root bridge (v3)
PCI: enable pci=bfsort by default on future Dell systems
PCI/PCIe: Clear Root PME Status bits early during system resume
PCI: pci-stub: ignore zero-length id parameters
x86/PCI: irq and pci_ids patch for Intel Patsburg
PCI: Skip id checking if no id is passed
PCI: fix __pci_device_probe kernel-doc warning
PCI: make pci_restore_state return void
PCI: Disable ASPM if BIOS asks us to
PCI: Add mask bit definition for MSI-X table
PCI: MSI: Move MSI-X entry definition to pci_regs.h
Fix up trivial conflicts in drivers/net/{skge.c,sky2.c} that had in the
meantime been converted to not use legacy PCI power management, and thus
no longer use pci_restore_state() at all (and that caused trivial
conflicts with the "make pci_restore_state return void" patch)
* git://git.infradead.org/battery-2.6: (21 commits)
power_supply: Add MAX17042 Fuel Gauge Driver
olpc_battery: Fix up XO-1.5 properties list
olpc_battery: Add support for CURRENT_NOW and VOLTAGE_NOW
olpc_battery: Add support for CHARGE_NOW
olpc_battery: Add support for CHARGE_FULL_DESIGN
olpc_battery: Ambient temperature is not available on XO-1.5
jz4740-battery: Should include linux/io.h
s3c_adc_battery: Add gpio_inverted field to pdata
power_supply: Don't use flush_scheduled_work()
power_supply: Fix use after free and memory leak
gpio-charger: Fix potential race between irq handler and probe/remove
gpio-charger: Provide default name for the power_supply
gpio-charger: Check result of kzalloc
jz4740-battery: Check if platform_data is supplied
isp1704_charger: Detect charger after probe
isp1704_charger: Set isp->dev before anything needs it
isp1704_charger: Detect HUB/Host chargers
isp1704_charger: Correct length for storing model
power_supply: Add gpio charger driver
jz4740-battery: Protect against concurrent battery readings
...
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
mfd: ab8500-core chip version cut 2.0 support
mfd: Flag WM831x /IRQ as a wake source
mfd: Convert WM831x away from legacy I2C PM operations
regulator: Support MAX8998/LP3974 DVS-GPIO
mfd: Support LP3974 RTC
i2c: Convert SCx200 driver from using raw PCI to platform device
x86: OLPC: convert olpc-xo1 driver from pci device to platform device
mfd: MAX8998/LP3974 hibernation support
mfd/ab8500: remove spi support
mfd: Remove ARCH_U8500 dependency from AB8500
misc: Make AB8500_PWM driver depend on U8500 due to PWM breakage
mfd: Add __devexit annotation for vx855_remove
mfd: twl6030 irq_data conversion.
gpio: Fix cs5535 printk warnings
misc: Fix cs5535 printk warnings
mfd: Convert Wolfson MFD drivers to use irq_data accessor function
mfd: Convert TWL4030 to new irq_ APIs
mfd: Convert tps6586x driver to new irq_ API
mfd: Convert tc6393xb driver to new irq_ APIs
mfd: Convert t7166xb driver to new irq_ API
...
Make wakeup events be reported by the PCI subsystem before attempting to
resume devices or queuing up runtime resume requests for them, because
wakeup events should be reported as soon as they have been detected.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After recent changes related to wakeup events pm_wakeup_event()
automatically checks if the given device is configured to signal wakeup,
so pci_wakeup_event() may be a static inline function calling
pm_wakeup_event() directly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCI sysfs ROM interface requires an enabling write to access the ROM
image, but the default file mode is 0400. The original proposed patch
adding sysfs ROM support was a true read-only interface, with the
enabling bit coming in as a feature request. I suspect it was simply an
oversight that the file mode didn't get updated to match the API.
Acked-by: Chris Wright <chrisw@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move the evaluation of acpi_pci_osc_control_set() (to request control of
PCI Express native features) into acpi_pci_root_add() to avoid calling
it many times for the same root complex with the same arguments.
Additionally, check if all of the requisite _OSC support bits are set
before calling acpi_pci_osc_control_set() for a given root complex.
References: https://bugzilla.kernel.org/show_bug.cgi?id=20232
Reported-by: Ozan Caglayan <ozan@pardus.org.tr>
Tested-by: Ozan Caglayan <ozan@pardus.org.tr>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
They got mixed up when the switch was converted to a table in 2007.
Signed-off-by: Oswald Buddenhagen <ossi@kde.org>
[ickle: minor changes for 2.6.37+]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Commit a1f5f22adc ("gpio: timbgpio:
irq_data conversion") was slightly too enthusiastic in converting
timbgpio_irq() over to take an irq_data * argument instead of an
unsigned int irq argument, as it is a flow handler, which still take
IRQ numbers for now. (And on top of that, it was using the wrong
accessors.)
This fixes it up, and seems to build without warnings.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LIO target is a full featured in-kernel target framework with the
following feature set:
High-performance, non-blocking, multithreaded architecture with SIMD
support.
Advanced SCSI feature set:
* Persistent Reservations (PRs)
* Asymmetric Logical Unit Assignment (ALUA)
* Protocol and intra-nexus multiplexing, load-balancing and failover (MC/S)
* Full Error Recovery (ERL=0,1,2)
* Active/active task migration and session continuation (ERL=2)
* Thin LUN provisioning (UNMAP and WRITE_SAMExx)
Multiprotocol target plugins
Storage media independence:
* Virtualization of all storage media; transparent mapping of IO to LUNs
* No hard limits on number of LUNs per Target; maximum LUN size ~750 TB
* Backstores: SATA, SAS, SCSI, BluRay, DVD, FLASH, USB, ramdisk, etc.
Standards compliance:
* Full compliance with IETF (RFC 3720)
* Full implementation of SPC-4 PRs and ALUA
Significant code cleanups done by Christoph Hellwig.
[jejb: fix up for new block bdev exclusive interface. Minor fixes from
Randy Dunlap and Dan Carpenter.]
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
SDEV_MEDIA_CHANGE event was first added by commit a341cd0f (SCSI: add
asynchronous event notification API) for SATA AN support and then
extended to cover generic media change events by commit 285e9670
([SCSI] sr,sd: send media state change modification events).
This event was mapped to block device in userland with all properties
stripped to simulate CHANGE event on the block device, which, in turn,
was used to trigger further userspace action on media change.
The recent addition of disk event framework kept this event for
backward compatibility but it turns out to be unnecessary and causes
erratic and inefficient behavior. The new disk event generates proper
events on the block devices and the compat events are mapped to block
device with all properties stripped, so the block device ends up
generating multiple duplicate events for single actual event.
This patch removes the compat event generation from both sr and sd as
suggested by Kay Sievers. Both existing and newer versions of udev
and the associated tools will behave better with the removal of these
events as they from the beginning were expecting events on the block
devices.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Replace sd_media_change() with sd_check_events().
* Move media removed logic into set_media_not_present() and
media_not_present() and set sdev->changed iff an existing media is
removed or the device indicates UNIT_ATTENTION.
* Make sd_check_events() sets sdev->changed if previously missing
media becomes present.
* Event is reported only if sdev->changed is set.
This makes media presence event reported if scsi_disk->media_present
actually changed or the device indicated UNIT_ATTENTION. For backward
compatibility, SDEV_EVT_MEDIA_CHANGE is generated each time
sd_check_events() detects media change event.
[jejb: fix boot failure]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The MAX17042 is a fuel gauge with an I2C interface for lithium-ion
betteries. Unlike its predecessor MAX17040, MAX17042 uses 16bit
registers. Besides, MAX17042 has much more features than MAX17040; e.g.,
a thermistor, current and current accumulation measurement, battery
internal resistance estimate, average values of measurement, and others.
This patch implements a driver for MAX17042.
In this initial release, we have implemented the most basic features of
a fuel gauge: measure the battery capacity and voltage.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This patch adds support for chip version 2.0 or cut 2.0.
One new interrupt latch register - latch 12 - is introduced.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x can generate wake events, some unconditionally, so flag
the primary IRQ as a wake source in order to help the CPU treat the
/IRQ signal appropriately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since the legacy bus PM operations are deprecated move the suspend
method over to dev_pm_ops.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The previous driver did not support BUCK1-DVS3, BUCK1-DVS4, and
BUCK2-DVS2 modes. This patch adds such modes and an option to block
setting buck1/2 voltages out of the preset values.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The first releases of LP3974 have a large delay in RTC registers,
which requires 2 seconds of delay after writing to a rtc register
(recommended by National Semiconductor's engineers)
before reading it.
If "rtc_delay" field of the platform data is true, the rtc driver
assumes that such delays are required. Although we have not seen
LP3974s without requiring such delays, we assume that such LP3974s
will be released soon (or they have done so already) and they are
supported by "lp3974" without setting "rtc_delay" at the platform
data.
This patch adds delays with msleep when writing values to RTC registers
if the platform data has rtc_delay set.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The SCx200 ACB driver supports ISA hardware as well as PCI. The PCI
hardware is CS5535/CS5536 based, and the device that it grabs is handled by
the cs5535-mfd driver. This converts the SCx200 driver to use a
platform_driver rather than the previous PCI hackery.
The driver used to manually track the iface list (via linked list); now it
only does this for ISA devices. PCI ifaces are handled through standard
driver model lists.
It's unclear what happens in case of errors in the old ISA code; rather than
pretending the code actually cares, I've dropped the (implicit) ignorance
of return values and marked it with a comment.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch makes the driver to save and restore register values
for hibernation.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since the Ab8500 v1.0, the SPI support is deprecated on the HW.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
While it is vanishingly unlikely that the device will be deployed on other
architectures removing the dependency facilitates build testing when doing
generic work on both the MFD core for the device and the subsystem drivers.
There appears to be no actual code dependency.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since we don't have a PWM API every PWM driver ends up exporting its
own version and we need to limit the platforms we try to build them on
in order to avoid multiple definitions. As the AB8500 is normally a
companion chip for the U8500 CPU depend on that architecture.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
drivers/gpio/cs5535-gpio.c: In function 'cs5535_gpio_probe':
drivers/gpio/cs5535-gpio.c:269: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
drivers/gpio/cs5535-gpio.c:269: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'
Use vsprintf extension %pR to format resource.
Original-patch-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
drivers/misc/cs5535-mfgpt.c: In function 'cs5535_mfgpt_probe':
drivers/misc/cs5535-mfgpt.c:320: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
drivers/misc/cs5535-mfgpt.c:320: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'
Use vsprintf extension %pR to format resource.
Original-patch-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Actually makes the code larger rathe rthan smaller but does provide some
isolation against core API changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to pass struct irq_data to irq_chip
operations. Update the TWL4030 driver to the new APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to supply struct irq_data to irq_chip
operations rather than an irq number. Update the tps6586x driver to the
new APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being update to pass struct irq_data to irq_chip rather
than an irq number to operations. Update tc6393 to the new API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to pass struct irq_data rather than an
irq number to irq_chip operations. Update the t7166xb driver to the new
APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to supply struct irq_data to irq_chip
operations rather than an irq number. Update the SMTPE driver to the new
APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being updated to pass struct irq_data to interrupt
operations, update the MAX8998 driver to the new API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq infrastructure is being converted to pass struct irq_data rather
than an irq number to irq_chip operations, update max8925 to the new APIs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Convert the jz4740-adc driver to use the recently introduced IRQ API
variants which are passed struct irq_data rather than an IRQ number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being converted to pass a struct irq_data to interrupt
operations rather than an IRQ number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The genirq core is being converted to pass a struct irq_data to interrupt
operations rather than an IRQ number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Russell King - ARM Linux
Linus Torvalds
Maciej Sosnowski
Nicholas Bellinger
Rafael J. Wysocki
Al Viro
Shreyas Bhatewara
Grant Likely
Frank Blaschka
Ursula Braun
David Howells
Russell King
Wei Yongquan
Nicolas Ferre
Eric Xu
Tomoya MORINAGA
Dave Airlie
Viresh Kumar
Mark Brown
Jean Delvare
Daniel Hellstrom
David S. Miller
Tejun Heo
Alex Williamson
Knut Petersen
Oswald Buddenhagen
Lennert Buytenhek
MyungJoo Ham
Mattias Wallin
Andres Salomon
Sundar Iyer
Axel Lin
Joe Perches