Commit Graph

135 Commits

Author SHA1 Message Date
Linus Torvalds 45b583b10a Merge 'akpm' patch series
* Merge akpm patch series: (122 commits)
  drivers/connector/cn_proc.c: remove unused local
  Documentation/SubmitChecklist: add RCU debug config options
  reiserfs: use hweight_long()
  reiserfs: use proper little-endian bitops
  pnpacpi: register disabled resources
  drivers/rtc/rtc-tegra.c: properly initialize spinlock
  drivers/rtc/rtc-twl.c: check return value of twl_rtc_write_u8() in twl_rtc_set_time()
  drivers/rtc: add support for Qualcomm PMIC8xxx RTC
  drivers/rtc/rtc-s3c.c: support clock gating
  drivers/rtc/rtc-mpc5121.c: add support for RTC on MPC5200
  init: skip calibration delay if previously done
  misc/eeprom: add eeprom access driver for digsy_mtc board
  misc/eeprom: add driver for microwire 93xx46 EEPROMs
  checkpatch.pl: update $logFunctions
  checkpatch: make utf-8 test --strict
  checkpatch.pl: add ability to ignore various messages
  checkpatch: add a "prefer __aligned" check
  checkpatch: validate signature styles and To: and Cc: lines
  checkpatch: add __rcu as a sparse modifier
  checkpatch: suggest using min_t or max_t
  ...

Did this as a merge because of (trivial) conflicts in
 - Documentation/feature-removal-schedule.txt
 - arch/xtensa/include/asm/uaccess.h
that were just easier to fix up in the merge than in the patch series.
2011-07-25 21:00:19 -07:00
Witold Szczeponik 29df8d8f87 pnpacpi: register disabled resources
When parsing PnP ACPI resource structures, it may happen that some of
the resources are disabled (in which case "the size" of the resource
equals zero).

The current solution is to skip these resources completely - with the
unfortunate side effect that they are not registered despite the fact
that they exist, after all.  (The downside of this approach is that
these resources cannot be used as templates for setting the actual
device's resources because they are missing from the template.) The
kernel's APM implementation does not suffer from this problem and
registers all resources regardless of "their size".

This patch fixes a problem with (at least) the vintage IBM ThinkPad 600E
(and most likely also with the 600, 600X, and 770X which have a very
similar layout) where some of its PnP devices support options where
either an IRQ, a DMA, or an IO port is disabled.  Without this patch,
the devices can not be configured using the
"/sys/bus/pnp/devices/*/resources" interface.

The manipulation of these resources is important because the 600E has
very demanding requirements.  For instance, the number of IRQs is not
sufficient to support all devices of the 600E.  Fortunately, some of the
devices, like the sound card's MPU-401 UART, can be configured to not
use any IRQ, hence freeing an IRQ for a device that requires one.
(Still, the device's "ResourceTemplate" requires an IRQ resource
descriptor which cannot be created if the resource has not been
registered in the first place.)

As an example, the dependent sets of the 600E's CSC0103 device (the
MPU-401 UART) are listed, with the patch applied, as:

  Dependent: 00 - Priority preferred
    port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding
    irq <none> High-Edge
  Dependent: 01 - Priority acceptable
    port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding
    irq 5,7,2/9,10,11,15 High-Edge

(The same result is obtained when PNPBIOS is used instead of PnP ACPI.)
Without the patch, the IRQ resource in the preferred option is not
listed at all:

  Dependent: 00 - Priority preferred
    port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding
  Dependent: 01 - Priority acceptable
    port 0x300-0x330, align 0xf, size 0x4, 16-bit address decoding
    irq 5,7,2/9,10,11,15 High-Edge

And in fact, the 600E's DSDT lists the disabled IRQ as an option, as can
be seen from the following excerpt from the DSDT:

	Name (_PRS, ResourceTemplate ()
	{
        StartDependentFn (0x00, 0x00)
        {
            IO (Decode16, 0x0300, 0x0330, 0x10, 0x04)
            IRQNoFlags () {}
        }
        StartDependentFn (0x01, 0x00)
        {
            IO (Decode16, 0x0300, 0x0330, 0x10, 0x04)
            IRQNoFlags () {5,7,9,10,11,15}
        }
        EndDependentFn ()
	})

With this patch applied, a user space program - or maybe even the kernel
- can allocate all devices' resources optimally.  For the 600E, this
means to find optimal resources for (at least) the serial port, the
parallel port, the infrared port, the MWAVE modem, the sound card, and
the MPU-401 UART.

The patch applies the idea to register disabled resources to all types
of resources, not just to IRQs, DMAs, and IO ports.  At the same time,
it mimics the behavior of the "pnp_assign_xxx" functions from
"drivers/pnp/manager.c" where resources with "no size" are considered
disabled.

No regressions were observed on hardware that does not require this
patch.

The patch is applied against 2.6.39.

NB: The kernel's current PnP interface does not allow for disabling individual
resources using the "/sys/bus/pnp/devices/$device/resources" file.  Assuming
this could be done, a device could be configured to use a disabled resource
using a simple series of calls:

  echo disable > /sys/bus/pnp/devices/$device/resources
  echo clear > /sys/bus/pnp/devices/$device/resources
  echo set irq disabled > /sys/bus/pnp/devices/$device/resources
  echo fill > /sys/bus/pnp/devices/$device/resources
  echo activate > /sys/bus/pnp/devices/$device/resources

This patch addresses only the parsing of PnP ACPI devices.

ChangeLog (v1 -> v2):
 - extend patch description
 - fix typo in patch itself

Signed-off-by: Witold Szczeponik <Witold.Szczeponik@gmx.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Adam Belay <abelay@mit.edu>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-07-25 20:57:17 -07:00
Joe Perches 28f65c11f2 treewide: Convert uses of struct resource to resource_size(ptr)
Several fixes as well where the +1 was missing.

Done via coccinelle scripts like:

@@
struct resource *ptr;
@@

- ptr->end - ptr->start + 1
+ resource_size(ptr)

and some grep and typing.

Mostly uncompiled, no cross-compilers.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-06-10 14:55:36 +02:00
Len Brown 6d1f23f204 Merge branch 'pnp' into release 2011-01-12 04:59:44 -05:00
Rafael J. Wysocki cc8e7a355c PNP / ACPI: Use DEVICE_ACPI_HANDLE() for device ACPI handle access
The PNP ACPI driver squirrels the ACPI handles of PNP devices' ACPI
companions, but this isn't correct, because those handles should be
accessed using the DEVICE_ACPI_HANDLE() macro operating on struct
device objects.

Using DEVICE_ACPI_HANDLE() in the PNP ACPI driver instead of the
driver's own copies of the ACPI handles allows us to avoid a problem
with docking stations where a machine docked before suspend to RAM
and undocked while suspended crashes during the subsequent resume (in
that case the ACPI companion of the PNP device in question doesn't
exist any more while the device is being resumed).  It also allows us
to avoid the problem where suspend to RAM fails when the machine was
undocked while suspended before (again, the ACPI companion of the PNP
device is not present any more while it is being suspended).

This change doesn't fix all of the the PNP ACPI driver's problems
with PNP devices in docking stations (generally speaking, the driver
has no idea that devices can come and go and doesn't even attempt to
handle such events), but at least it makes suspend work for the
users of docking stations who don't use the PNP devices located in
there.

References: https://bugzilla.kernel.org/show_bug.cgi?id=15100

Reported-and-tested-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2011-01-11 15:20:40 -05:00
Jan Beulich 66c3ec4f1f ACPI/PNP: avoid section mismatch warning
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2010-12-11 02:01:47 -05:00
Thomas Renninger 803711afdb PNP: Compile all pnp built-in stuff in one module namespace
This is cleanup mostly, nothing urgent.
I came up with it when looking at dynamic debug which can
enable pr_debug messages at runtime or boot param
for a specific module.

Advantages:
  - Any pnp code can make use of the moduleparam.h interface, the modules
    will show up as pnp.param.
  - Passing pnp.ddebug as kernel boot param will enable all pnp debug messages
    with my previous patch and CONFIG_DYNAMIC_DEBUG enabled.

Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2010-10-27 02:23:44 -04:00
Len Brown b10b977b79 Merge branch 'pnpacpi-invalid-device-id' into release 2010-10-25 02:13:44 -04:00
Thomas Renninger 620e112cfe ACPI/PNP: A HID value of an object never changes -> make it const
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
2010-10-01 19:28:51 -04:00
Dmitry Torokhov 420a0f6637 PNPACPI: cope with invalid device IDs
If primary ID (HID) is invalid try locating first valid ID on compatible
ID list before giving up.

This helps, for example, to recognize i8042 AUX port on Sony Vaio VPCZ1
which uses SNYSYN0003 as HID. Without the patch users are forced to
boot with i8042.nopnp to make use of their touchpads.

Tested-by: Jan-Hendrik Zab <jan@jhz.name>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Len Brown <len.brown@intel.com>
2010-10-01 02:08:59 -04:00
Alan Stern b14e033e17 PNPACPI: Add support for remote wakeup
This patch (as1354) adds remote-wakeup support to the pnpacpi driver.
The new can_wakeup method also allows other PNP protocol drivers
(pnpbios or iaspnp) to add wakeup support, but I don't know enough
about how they work to actually do it.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2010-07-19 01:58:48 +02:00
Bjorn Helgaas f238b414a7 PNPACPI: compute Address Space length rather than using _LEN
ACPI _CRS Address Space Descriptors have _MIN, _MAX, and _LEN.  Linux has
been computing Address Spaces as [_MIN to _MIN + _LEN - 1].  Based on the
tests in the bug reports below, Windows apparently uses [_MIN to _MAX].

Per spec (ACPI 4.0, Table 6-40), for _CRS fixed-size, fixed location
descriptors, "_LEN must be (_MAX - _MIN + 1)", and when that's true, it
doesn't matter which way we compute the end.  But of course, there are
BIOSes that don't follow this rule, and we're better off if Linux handles
those exceptions the same way as Windows.

This patch makes Linux use [_MIN to _MAX], as Windows seems to do.  This
effectively reverts 3162b6f0c5 and replaces it with simpler code.

    https://bugzilla.kernel.org/show_bug.cgi?id=14337 (round)
    https://bugzilla.kernel.org/show_bug.cgi?id=15480 (truncate)

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2010-04-28 21:44:49 -04:00
Len Brown c25f7cf203 Merge branches 'battery', 'bugzilla-14667', 'bugzilla-15096', 'bugzilla-15480', 'bugzilla-15521', 'bugzilla-15605', 'gpe-reference-counters', 'misc', 'pxm-fix' and 'video-random-key' into release 2010-04-06 17:06:22 -04:00
Bjorn Helgaas 3162b6f0c5 PNPACPI: truncate _CRS windows with _LEN > _MAX - _MIN + 1
The ACPI spec (sec 6.4.3.5 in v4.0) requires that for Address Space Resource
Descriptors, _LEN <= _MAX - _MIN + 1 in all cases, but there are BIOSes that
violate this.  We experimentally determined that Windows truncates the
resource so it doesn't extend past _MAX, so let's do the same thing in
Linux.

http://bugzilla.kernel.org/show_bug.cgi?id=15480

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
2010-04-04 01:33:43 -04:00
Tejun Heo 5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Bjorn Helgaas 7e0e9c0427 PNPACPI: add bus number support
Add support for bus number resources.  This is for bridges with a range of
bus numbers behind them.  Previously, PNP ignored bus number resources.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2010-03-14 20:08:38 -04:00
Bjorn Helgaas fa35b49260 PNPACPI: add window support
Add support for resource windows.  This is for bridge resources, i.e.,
regions where a bridge forwards transactions from the primary to the
secondary side.  This does not add support for *setting* windows via
the /proc interface.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2010-03-14 20:08:37 -04:00
Bjorn Helgaas 9065ce4500 PNP: add interface to retrieve ACPI device from a PNPACPI device
Add pnp_acpi_device(pnp_dev), which takes a PNP device and returns the
associated ACPI device (or NULL, if the device is not a PNPACPI device).

This allows us to write a PNP driver that can manage both traditional
PNPBIOS and ACPI devices, treating ACPI-only functionality as an optional
extension.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2009-12-15 17:35:26 -05:00
Bjorn Helgaas c4da6940a7 PNPACPI: save struct acpi_device, not just acpi_handle
Some drivers need to look at things in the acpi_device structure
besides the handle.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2009-12-11 00:50:48 -05:00
Bjorn Helgaas 1131b938f0 ACPI: remove acpi_device.flags.hardware_id
Every acpi_device has at least one ID (if there's no _HID or _CID, we
give it a synthetic or default ID).  So there's no longer a need to
check whether an ID exists; we can just use it.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2009-09-25 15:09:48 -04:00
Bjorn Helgaas 7f47fa6c2f ACPI: maintain a single list of _HID and _CID IDs
There's no need to treat _HID and _CID differently.  Keeping them in
a single list makes code that uses the IDs a little simpler because it
can just traverse the list rather than checking "do we have a HID?",
"do we have any CIDs?"

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2009-09-25 15:09:31 -04:00
Bjorn Helgaas ea8d82fd31 ACPI: use acpi_device_hid() when possible
Use acpi_device_hid() rather than accessing acpi_device.pnp.hardware_id
directly.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2009-09-25 14:25:52 -04:00
Bob Moore 15b8dd53f5 ACPICA: Major update for acpi_get_object_info external interface
Completed a major update for the acpi_get_object_info external interface.
Changes include:
 - Support for variable, unlimited length HID, UID, and CID strings
 - Support Processor objects the same as Devices (HID,UID,CID,ADR,STA, etc.)
 - Call the _SxW power methods on behalf of a device object
 - Determine if a device is a PCI root bridge
 - Change the ACPI_BUFFER parameter to ACPI_DEVICE_INFO.
These changes will require an update to all callers of this interface.
See the ACPICA Programmer Reference for details.

Also, update all invocations of acpi_get_object_info interface

Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2009-08-27 10:17:15 -04:00
Len Brown fbe8cddd2d Merge branches 'acerhdf', 'acpi-pci-bind', 'bjorn-pci-root', 'bugzilla-12904', 'bugzilla-13121', 'bugzilla-13396', 'bugzilla-13533', 'bugzilla-13612', 'c3_lock', 'hid-cleanups', 'misc-2.6.31', 'pdc-leak-fix', 'pnpacpi', 'power_nocheck', 'thinkpad_acpi', 'video' and 'wmi' into release 2009-06-24 01:19:50 -04:00
Ingo Molnar 3d58f48ba0 Merge branch 'linus' into irq/numa
Conflicts:
	arch/mips/sibyte/bcm1480/irq.c
	arch/mips/sibyte/sb1250/irq.c

Merge reason: we gathered a few conflicts plus update to latest upstream fixes.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-06-01 21:06:21 +02:00
Bjorn Helgaas 8cb24c8fd7 PNPACPI: parse Extended Address Space Descriptors
Extended Address Space Descriptors are new in ACPI 3.0 and allow the
BIOS to communicate device resource cacheability attributes (write-back,
write-through, uncacheable, etc) to the OS.

Previously, PNPACPI ignored these descriptors, so if a BIOS used them,
a device could be responding at addresses the OS doesn't know about.
This patch adds support for these descriptors in _CRS and _PRS.  We
don't attempt to encode them for _SRS (just like we don't attempt to
encode the existing 16-, 32-, and 64-bit Address Space Descriptors).

Unfortunately, I don't have a way to test this.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2009-05-27 21:25:00 -04:00
Len Brown 19bde778c1 ACPI: suspend: don't let device _PS3 failure prevent suspend
6328a57401
"Enable PNPACPI _PSx Support, v3"

added a call to acpi_bus_set_power(handle, ACPI_STATE_D3)
to pnpacpi_disable_resource() before the existing call
to evaluate _DIS on the device.

This caused suspend to fail on the system in
http://bugzilla.kernel.org/show_bug.cgi?id=13243
because the sanity check to verify we entered _PS3
failed on the serial port.

As a work-around, that sanity check can be disabled
system-wide with "acpi.power_nocheck=1"

Or perhaps we should just shrug off the _PS3 failure
and carry on with _DIS like we used to -- which is
what this patch does.

Signed-off-by: Len Brown <len.brown@intel.com>
2009-05-08 00:22:29 -04:00
Yinghai Lu a2f809b08a irq: change ACPI GSI APIs to also take a device argument
We want to use dev_to_node() later on, to be aware of the 'home node'
of the GSI in question.

[ Impact: cleanup, prepare the IRQ code to be more NUMA aware ]

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Len Brown <lenb@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Len Brown <lenb@kernel.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-acpi@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
LKML-Reference: <49F65560.20904@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-04-28 12:21:17 +02:00
Witold Szczeponik 6328a57401 Enable PNPACPI _PSx Support, v3
(This is an update to the patch presented earlier in
http://lkml.org/lkml/2008/12/8/284, with new error handling.)

This patch sets the power of PnP ACPI devices to D0 when they
are activated and to D3 when they are disabled.  The latter is
in correspondence with the ACPI 3.0 specification, whereas the
former is added in order to be able to power up a device after
it has been previously disabled (or when booting up a system).
(As a consequence, the patch makes the PnP ACPI code more ACPI
compliant.)

Section 6.2.2 of the ACPI Specification (at least versions 1.0b
and 3.0a) states: "Prior to running this control method [_DIS],
the OS[PM] will have already put the device in the D3 state."
Unfortunately, there is no clear statement as to when to put
a device in the D0 state. :-( Therefore, the patch executes the
method calls as _PS3/_DIS and _SRS/_PS0. What is clear: "If the
device is disabled, _SRS enables the device at the specified
resources." (From the ACPI 3.0a Specification.)

The patch fixes a problem with some IBM ThinkPads (at least the
600E and the 600X) where the serial ports have a dedicated
power source that needs to be brought up before the serial port
can be used.  Without this patch, the serial port is enabled
but has no power. (In the past, the tpctl utility had to be
utilized to turn on the power, but support for this feature
stopped with version 5.9 as it did not support the more recent
kernel versions.)

The error handlers that handle any errors that can occur during
the power up/power down phases return the error codes to the
caller directly.  Comments welcome! :-)

No regressions were observed on hardware that does not require
this patch.

The patch is applied against 2.6.27.x.

Signed-off-by: Witold Szczeponik <Witold.Szczeponik@gmx.net>
Acked-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2009-04-03 21:44:10 -04:00
Lin Ming ea7e96e0f2 ACPI: remove private acpica headers from driver files
External driver files should not include any private acpica headers.

Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-12-31 01:15:22 -05:00
Len Brown 057316cc6a Merge branch 'linus' into test
Conflicts:
	MAINTAINERS
	arch/x86/kernel/acpi/boot.c
	arch/x86/kernel/acpi/sleep.c
	drivers/acpi/Kconfig
	drivers/pnp/Makefile
	drivers/pnp/quirks.c

Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-23 00:11:07 -04:00
Len Brown 4dff4e7f6c Merge branch 'pnp-debug' into test 2008-10-22 23:28:43 -04:00
Zhao Yakui 39a0ad8710 ACPI : Load device driver according to the status of acpi device
According to ACPI spec when the status of some device is not present
but functional, the device is valid and the children of this device
should be enumerated. It means that the device should be added to
linux acpi device tree. But the device driver for this device should not
be loaded.
    The detailed info can be found in the section 6.3.7 of ACPI 3.0b spec.
    _STA may return bit 0 clear (not present) with bit 3 set (device is
functional). This case is used to indicate a valid device for which no
device driver should be loaded (for example, a bridge device.).
Children of this device may be present and valid. OS should continue
enumeration below a device whose _STA returns this bit combination

http://bugzilla.kernel.org/show_bug.cgi?id=3358

Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-22 18:00:50 -04:00
Bjorn Helgaas ac88a8f3f7 PNP: remove old CONFIG_PNP_DEBUG option
CONFIG_PNP_DEBUG is no longer used to turn on dev_dbg() in PNP,
since we have pnp_dbg() which can be enabled at boot-time, so
this patch removes the config option.

Note that pnp_dock_event() checks "#ifdef DEBUG".  But there's
never been a clear path for enabling that via configgery.  It
happened that CONFIG_PNP_DEBUG enabled it after 1bd17e63a0,
but that was accidental and only in 2.6.26.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-10 23:35:33 -04:00
Bjorn Helgaas 2f53432c2a PNP: convert to using pnp_dbg()
pnp_dbg() is equivalent to dev_dbg() except that we can turn it
on at boot-time with the "pnp.debug" kernel parameter, so we don't
have to build a new kernel image.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-10 23:34:33 -04:00
Bjorn Helgaas c865d2f6eb PNP: convert the last few pnp_info() uses to printk()
There are only a few remaining uses of pnp_info(), so I just
converted them to printk and removed the pnp_err(), pnp_info(),
pnp_warn(), and pnp_dbg() wrappers.

I also removed a couple debug messages that don't seem useful any
more ("driver registered", "driver unregistered", "driver attached").

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-10 23:27:18 -04:00
Bjorn Helgaas 958a1fdd39 PNPACPI: use dev_printk when possible
Use dev_printk() when possible for more informative error messages.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-10-10 23:24:27 -04:00
Linus Torvalds ed458df4d2 PnP: move pnpacpi/pnpbios_init to after PCI init
We already did that a long time ago for pnp_system_init, but
pnpacpi_init and pnpbios_init remained as subsys_initcalls, and get
linked into the kernel before the arch-specific routines that finalize
the PCI resources (pci_subsys_init).

This means that the PnP routines would either register their resources
before the PCI layer could, or would be unable to check whether a PCI
resource had already been registered.  Both are problematic.

I wanted to do this before 2.6.27, but every time we change something
like this, something breaks.  That said, _every_ single time we trust
some firmware (like PnP tables) more than we trust the hardware itself
(like PCI probing), the problems have been worse.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-10 08:00:17 -07:00
Bjorn Helgaas de82ff783b PNPACPI: ignore the producer/consumer bit for extended IRQ descriptors
The Extended Interrupt descriptor has a producer/consumer bit, but
it's not clear what that would mean, and existing BIOSes use the bit
inconsistently.  This patch makes Linux PNPACPI ignore the bit.

The ACPI spec contains examples of PCI Interrupt Link devices marked
as ResourceProducers, but many BIOSes mark them as ResourceConsumers.

I also checked with a Windows contact, who said:

    Windows uses only "resource consumer" when dealing with
    interrupts.  There's no useful way of looking at a resource
    producer of interrupts.

    ... NT-based Windows largely infers the producer/consumer stuff
    from the device type and ignores the bits in the namespace.  This
    was necessary because Windows 98 ignored them and early namespaces
    contained random junk.

The reason I want to change this is because if PNPACPI devices exclude
ResourceProducer IRQ resources, we can't write PNP drivers for those
devices.

For example, on machines such as the the HP rx7620, rx7640, rx8620,
rx8640, and Superdome, HPET interrupts are ResourceProducers.  The
HPET driver currently has to use acpi_bus_register_driver() and do its
own _CRS parsing, even though it requires absolutely no ACPI-specific
functionality.

It would be better if the HPET driver were a PNP driver and took
advantage of the _CRS parsing built into PNPACPI.

This producer/consumer check was originally added here:
    http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=2b8de5f50e4a302b83ebcd5b0120621336d50bd6

to fix this bug:
    http://bugzilla.kernel.org/show_bug.cgi?id=6292

However, the bug was related only to memory and I/O port resources,
where the distinction is sensible and important to Linux.  Given that
the distinction is muddled for IRQ resources, I think it was a mistake
to add the check there.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
2008-08-25 12:04:44 +02:00
Bjorn Helgaas 40ab4f4c1d PNPACPI: add support for HP vendor-specific CCSR descriptors
The HP CCSR descriptor describes MMIO address space that should appear
as a MEM resource.  This patch adds support for parsing these descriptors
in the _CRS data.

The visible effect of this is that these MEM resources will appear
in /sys/devices/pnp0/.../resources, which means that "lspnp -v" will
report it, user applications can use this to locate device CSR space,
and kernel drivers can use the normal PNP resource accessors to
locate them.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
2008-07-16 23:27:07 +02:00
Bjorn Helgaas 1f32ca31e7 PNP: convert resource options to single linked list
ISAPNP, PNPBIOS, and ACPI describe the "possible resource settings" of
a device, i.e., the possibilities an OS bus driver has when it assigns
I/O port, MMIO, and other resources to the device.

PNP used to maintain this "possible resource setting" information in
one independent option structure and a list of dependent option
structures for each device.  Each of these option structures had lists
of I/O, memory, IRQ, and DMA resources, for example:

  dev
    independent options
      ind-io0  -> ind-io1  ...
      ind-mem0 -> ind-mem1 ...
      ...
    dependent option set 0
      dep0-io0  -> dep0-io1  ...
      dep0-mem0 -> dep0-mem1 ...
      ...
    dependent option set 1
      dep1-io0  -> dep1-io1  ...
      dep1-mem0 -> dep1-mem1 ...
      ...
    ...

This data structure was designed for ISAPNP, where the OS configures
device resource settings by writing directly to configuration
registers.  The OS can write the registers in arbitrary order much
like it writes PCI BARs.

However, for PNPBIOS and ACPI devices, the OS uses firmware interfaces
that perform device configuration, and it is important to pass the
desired settings to those interfaces in the correct order.  The OS
learns the correct order by using firmware interfaces that return the
"current resource settings" and "possible resource settings," but the
option structures above doesn't store the ordering information.

This patch replaces the independent and dependent lists with a single
list of options.  For example, a device might have possible resource
settings like this:

  dev
    options
      ind-io0 -> dep0-io0 -> dep1->io0 -> ind-io1 ...

All the possible settings are in the same list, in the order they
come from the firmware "possible resource settings" list.  Each entry
is tagged with an independent/dependent flag.  Dependent entries also
have a "set number" and an optional priority value.  All dependent
entries must be assigned from the same set.  For example, the OS can
use all the entries from dependent set 0, or all the entries from
dependent set 1, but it cannot mix entries from set 0 with entries
from set 1.

Prior to this patch PNP didn't keep track of the order of this list,
and it assigned all independent options first, then all dependent
ones.  Using the example above, that resulted in a "desired
configuration" list like this:

  ind->io0 -> ind->io1 -> depN-io0 ...

instead of the list the firmware expects, which looks like this:

  ind->io0 -> depN-io0 -> ind-io1 ...

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-07-16 23:27:07 +02:00
Bjorn Helgaas e2a1a6f1cf PNP: remove extra 0x100 bit from option priority
When building resource options, ISAPNP and PNPBIOS set the priority
to something like "0x100 | PNP_RES_PRIORITY_ACCEPTABLE", but we
immediately mask off the 0x100 again in pnp_build_option(), so that
bit looks superfluous.

Thanks to Rene Herman <rene.herman@gmail.com> for pointing this out.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-07-16 23:27:07 +02:00
Bjorn Helgaas fe2cf598e6 PNPACPI: ignore _PRS interrupt numbers larger than PNP_IRQ_NR
ACPI Extended Interrupt Descriptors can encode 32-bit interrupt
numbers, so an interrupt number may exceed the size of the bitmap
we use to track possible IRQ settings.

To avoid corrupting memory, complain and ignore too-large interrupt
numbers.

There's similar code in pnpacpi_parse_irq_option(), but I didn't
change that because the small IRQ descriptor can only encode
IRQs 0-15, which do not exceed bitmap size.

In the future, we could handle IRQ numbers greater than PNP_IRQ_NR
by replacing the bitmap with a table or list.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-07-16 23:27:07 +02:00
Bjorn Helgaas c227536b4c PNP: centralize resource option allocations
This patch moves all the option allocations (pnp_mem, pnp_port, etc)
into the pnp_register_{mem,port,irq,dma}_resource() functions.  This
will make it easier to rework the option data structures.

The non-trivial part of this patch is the IRQ handling.  The backends
have to allocate a local pnp_irq_mask_t bitmap, populate it, and pass
a pointer to pnp_register_irq_resource().

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-07-16 23:27:07 +02:00
Bjorn Helgaas 7aefff5185 PNP: introduce pnp_irq_mask_t typedef
This adds a typedef for the IRQ bitmap, which should cause
no functional change, but will make it easier to pass a
pointer to a bitmap to pnp_register_irq_resource().

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-07-16 23:27:06 +02:00
Bjorn Helgaas 08c9f262f2 PNP: define PNP-specific IORESOURCE_IO_* flags alongside IRQ, DMA, MEM
PNP previously defined PNP_PORT_FLAG_16BITADDR and PNP_PORT_FLAG_FIXED
in a private header file, but put those flags in struct resource.flags
fields.  Better to make them IORESOURCE_IO_* flags like the existing
IRQ, DMA, and MEM flags.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-07-16 23:27:06 +02:00
Bjorn Helgaas 5acf914157 PNPACPI: keep disabled resources when parsing current config
When we parse a device's _CRS data (the current resource settings),
we should keep track of everything we find, even if it's currently
disabled or invalid.

This is what we already do for ISAPNP and PNPBIOS, and it helps
keep things matched up when we subsequently re-encode resources.
For example, consider a device with (mem, irq0, irq1, io), where
irq0 is disabled.  If we drop irq0 when parsing the _CRS, we will
mistakenly put irq1 in the irq0 slot when we encode resources
for an _SRS call.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
2008-07-16 23:27:06 +02:00
Bjorn Helgaas aee3ad815d PNP: replace pnp_resource_table with dynamically allocated resources
PNP used to have a fixed-size pnp_resource_table for tracking the
resources used by a device.  This table often overflowed, so we've
had to increase the table size, which wastes memory because most
devices have very few resources.

This patch replaces the table with a linked list of resources where
the entries are allocated on demand.

This removes messages like these:

    pnpacpi: exceeded the max number of IO resources
    00:01: too many I/O port resources

References:

    http://bugzilla.kernel.org/show_bug.cgi?id=9535
    http://bugzilla.kernel.org/show_bug.cgi?id=9740
    http://lkml.org/lkml/2007/11/30/110

This patch also changes the way PNP uses the IORESOURCE_UNSET,
IORESOURCE_AUTO, and IORESOURCE_DISABLED flags.

Prior to this patch, the pnp_resource_table entries used the flags
like this:

    IORESOURCE_UNSET
	This table entry is unused and available for use.  When this flag
	is set, we shouldn't look at anything else in the resource structure.
	This flag is set when a resource table entry is initialized.

    IORESOURCE_AUTO
	This resource was assigned automatically by pnp_assign_{io,mem,etc}().

	This flag is set when a resource table entry is initialized and
	cleared whenever we discover a resource setting by reading an ISAPNP
	config register, parsing a PNPBIOS resource data stream, parsing an
	ACPI _CRS list, or interpreting a sysfs "set" command.

	Resources marked IORESOURCE_AUTO are reinitialized and marked as
	IORESOURCE_UNSET by pnp_clean_resource_table() in these cases:

	    - before we attempt to assign resources automatically,
	    - if we fail to assign resources automatically,
	    - after disabling a device

    IORESOURCE_DISABLED
	Set by pnp_assign_{io,mem,etc}() when automatic assignment fails.
	Also set by PNPBIOS and PNPACPI for:

	    - invalid IRQs or GSI registration failures
	    - invalid DMA channels
	    - I/O ports above 0x10000
	    - mem ranges with negative length

After this patch, there is no pnp_resource_table, and the resource list
entries use the flags like this:

    IORESOURCE_UNSET
	This flag is no longer used in PNP.  Instead of keeping
	IORESOURCE_UNSET entries in the resource list, we remove
	entries from the list and free them.

    IORESOURCE_AUTO
	No change in meaning: it still means the resource was assigned
	automatically by pnp_assign_{port,mem,etc}(), but these functions
	now set the bit explicitly.

	We still "clean" a device's resource list in the same places,
	but rather than reinitializing IORESOURCE_AUTO entries, we
	just remove them from the list.

	Note that IORESOURCE_AUTO entries are always at the end of the
	list, so removing them doesn't reorder other list entries.
	This is because non-IORESOURCE_AUTO entries are added by the
	ISAPNP, PNPBIOS, or PNPACPI "get resources" methods and by the
	sysfs "set" command.  In each of these cases, we completely free
	the resource list first.

    IORESOURCE_DISABLED
	In addition to the cases where we used to set this flag, ISAPNP now
	adds an IORESOURCE_DISABLED resource when it reads a configuration
	register with a "disabled" value.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
2008-07-16 23:27:05 +02:00
David Brownell 2fe2de5f6c ACPI PM: acpi_pm_device_sleep_state() cleanup
Get rid of a superfluous acpi_pm_device_sleep_state() parameter.  The
only legitimate value of that parameter must be derived from the first
parameter, which is what all the callers already do.  (However, this
does not address the fact that ACPI still doesn't set up those flags.)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-07-16 23:27:02 +02:00
Bjorn Helgaas 36d872a370 PNPACPI: use _CRS IRQ descriptor length for _SRS
When configuring the resources of an ACPI device, we first evaluate _CRS
to get a template of resource descriptors, then fill in the specific
resource values we want, and finally evaluate _SRS to actually configure
the device.

Some resources have optional fields, so the size of encoded descriptors
varies depending on the specific values.  For example, IRQ descriptors can
be either two or three bytes long.  The third byte contains triggering
information and can be omitted if the IRQ is edge-triggered and active
high.

The BIOS often assumes that IRQ descriptors in the _SRS buffer use the
same format as those in the _CRS buffer, so this patch enforces that
constraint.

The "Start Dependent Function" descriptor also has an optional byte, but
we don't currently encode those descriptors, so I didn't do anything for
those.

I have tested this patch on a Toshiba Portege 4000.  Without the patch,
parport_pc claims the parallel port only if I use "pnpacpi=off".  This
patch makes it work with PNPACPI.

This is an extension of a patch by Tom Jaeger:
    http://bugzilla.kernel.org/show_bug.cgi?id=9487#c42

References:
    http://bugzilla.kernel.org/show_bug.cgi?id=5832 Enabling ACPI Plug and Play in kernels >2.6.9 kills Parallel support
    http://bugzilla.kernel.org/show_bug.cgi?id=9487 buggy firmware expects four-byte IRQ resource descriptor (was: Serial port disappears after Suspend on Toshiba R25)
    http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=1d5b285da1893b90507b081664ac27f1a8a3dc5b related ACPICA fix

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
2008-06-11 19:13:46 -04:00