No other SPI controller has this field, and SPI clients should be setting
this up in their own drivers. So drop it from the Blackfin controller to
keep people from using it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Each transfer may have its own bits per word.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This controller is only for blackfin 5xx soc, so rename it to BFIN5XX
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently, if we request for frequency greater than maximum possible, spi driver
returns error.
For example, if the spi block src frequency is 333/4 MHz, i.e. 83.33.. MHz,
maximum frequency programmable would be src/2. Which would come around 41.6...
It is difficult to pass frequency in these figures. We normally try to program
in round figures, like 42 MHz and it should get programmed to <=
requested_frequency, i.e. 41.6...
For this to happen, we must not return error even if requested freq is higher
than max possible. But should program it to max possible.
Reported-by: Vinit Kamalaksha Shenoy <vinit.shenoy@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We were not properly advertising the MODE bits supported by this driver, fix
that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We do not need to use a flag to indicate if the master driver is stopping
it is sufficient to perform spi master unregistering in the platform
driver's remove function.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch converts the bcm63xx SPI driver to use the SPI infrastructure
pump message queue. Since we were previously sleeping in the SPI
driver's transfer() function (which is not allowed) this is now fixed as well.
To complete that conversion a certain number of changes have been made:
- the transfer len is split into multiple hardware transfers in case its
size is bigger than the hardware FIFO size
- the FIFO refill is no longer done in the interrupt context, which was a
bad idea leading to quick interrupt handler re-entrancy
Tested-by: Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
A new enum indicating the dma channel direction was introduced by:
commit 49920bc669
dmaengine: add new enum dma_transfer_direction
The following commit changed spi-ep93xx to use the new enum:
commit a485df4b44
spi, serial: move to dma_transfer_direction
In doing so a sparse warning was introduced:
warning: mixing different enum types
int enum dma_data_direction versus
int enum dma_transfer_direction
This is produced because the 'dir' passed in ep93xx_spi_dma_prepare
is an enum dma_data_direction and is being used to set the
dma_slave_config 'direction' which is now an enum dma_transfer_direction.
Fix this by converting spi-ep93xx to use the new enum type in all
places.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
calculate_effective_freq() was still not optimized and there were cases when it
returned without error and with values of cpsr and scr as zero.
Also, the variable named found is not used well.
This patch targets to optimize and correct this routine. Tested for SPEAr.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Vinit Kamalaksha Shenoy <vinit.shenoy@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
pl022 ssp controller supports word lengths from 4 to 16 (or 32) bits.
Currently implemented checks were incorrect. It has following check
if (pl022->vendor->max_bpw >= 32)
which must be checking for <=.
Also error print message is incorrect, that prints "range is from 1 to
16".
Fix both these issues.
Signed-off-by: Vinit Shenoy <vinit.shenoy@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pull ARM fixes from Russell King:
"Nothing too disasterous, the biggest thing being the removal of the
regulator support for vcore in the AMBA driver; only one SoC was using
this and it got broken during the last merge window, which then
started causing problems for other people. Mutual agreement was
reached for it to be removed."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7386/1: jump_label: fixup for rename to static_key
ARM: 7384/1: ThumbEE: Disable userspace TEEHBR access for !CONFIG_ARM_THUMBEE
ARM: 7382/1: mm: truncate memory banks to fit in 4GB space for classic MMU
ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus
ARM: 7383/1: nommu: populate vectors page from paging_init
ARM: 7381/1: nommu: fix typo in mm/Kconfig
ARM: 7380/1: DT: do not add a zero-sized memory property
ARM: 7379/1: DT: fix atags_to_fdt() second call site
ARM: 7366/3: amba: Remove AMBA level regulator support
ARM: 7377/1: vic: re-read status register before dispatching each IRQ handler
ARM: 7368/1: fault.c: correct how the tsk->[maj|min]_flt gets incremented
Miscellaneous driver bug fixes. No major changes in this branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tw/j
-----END PGP SIGNATURE-----
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull SPI bug fixes from Grant Likely:
"Miscellaneous driver bug fixes. No major changes in this branch."
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi/imx: prevent NULL pointer dereference in spi_imx_probe()
spi/imx: mark base member in spi_imx_data as __iomem
spi/mpc83xx: fix NULL pdata dereference bug
spi/davinci: Fix DMA API usage in davinci
spi/pL022: include types.h to remove compilation warnings
The AMBA bus regulator support is being used to model on/off switches
for power domains which isn't terribly idiomatic for modern kernels with
the generic power domain code and creates integration problems on platforms
which don't use regulators for their power domains as it's hard to tell
the difference between a regulator that is needed but failed to be provided
and one that isn't supposed to be there (though DT does make that easier).
Platforms that wish to use the regulator API to manage their power domains
can indirect via the power domain interface.
This feature is only used with the vape supply of the db8500 PRCMU
driver which supplies the UARTs and MMC controllers, none of which have
support for managing vcore at runtime in mainline (only pl022 SPI
controller does). Update that supply to have an always_on constraint
until the power domain support for the system is updated so that it is
enabled for these users, this is likely to have no impact on practical
systems as probably at least one of these devices will be active and
cause AMBA to hold the supply on anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When no platform_data is present and either 'spi-num-chipselects' is
not defined in the DT or 'cs-gpios' has less entries than
'spi-num-chipselects' specifies, the NULL platform_data pointer is
being dereferenced.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 178db7d3, "spi: Fix device unregistration when unregistering
the bus master", changed device initialization to be children of the
bus master, not children of the bus masters parent device. The pdata
pointer used in fsl_spi_chipselect must updated to reflect the changed
initialization.
Signed-off-by: Kenth Eriksson <kenth.eriksson@transmode.com>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The driver uses NULL for dma_unmap_single instead of
the struct device that the API expects.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Tested-by: Akshay Shankarmurthy <akshay.s@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pull slave-dmaengine update from Vinod Koul:
"This includes the cookie cleanup by Russell, the addition of context
parameter for dmaengine APIs, more arm dmaengine driver cleanup by
moving code to dmaengine, this time for imx by Javier and pl330 by
Boojin along with the usual driver fixes."
Fix up some fairly trivial conflicts with various other cleanups.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (67 commits)
dmaengine: imx: fix the build failure on x86_64
dmaengine: i.MX: Fix merge of cookie branch.
dmaengine: i.MX: Add support for interleaved transfers.
dmaengine: imx-dma: use 'dev_dbg' and 'dev_warn' for messages.
dmaengine: imx-dma: remove 'imx_dmav1_baseaddr' and 'dma_clk'.
dmaengine: imx-dma: remove unused arg of imxdma_sg_next.
dmaengine: imx-dma: remove internal structure.
dmaengine: imx-dma: remove 'resbytes' field of 'internal' structure.
dmaengine: imx-dma: remove 'in_use' field of 'internal' structure.
dmaengine: imx-dma: remove sg member from internal structure.
dmaengine: imx-dma: remove 'imxdma_setup_sg_hw' function.
dmaengine: imx-dma: remove 'imxdma_config_channel_hw' function.
dmaengine: imx-dma: remove 'imxdma_setup_mem2mem_hw' function.
dmaengine: imx-dma: remove dma_mode member of internal structure.
dmaengine: imx-dma: remove data member from internal structure.
dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c
dmaengine: at_hdmac: add slave config operation
dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclic
dmaengine/dma_slave: introduce inline wrappers
dma: imx-sdma: Treat firmware messages as warnings instead of erros
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
This branch contains a number of updates for device tree support on
several ARM platforms, in particular:
* AT91 continues the device tree conversion adding support for a number of
on-chip drivers and other functionality
* ux500 adds probing of some of the core SoC blocks through device tree
* Initial device tree support for ST SPEAr600 platforms
* kirkwood continues the conversion to device-tree probing
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wiKV
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: More device tree support updates" from Olof Johansson:
"This branch contains a number of updates for device tree support on
several ARM platforms, in particular:
* AT91 continues the device tree conversion adding support for a
number of on-chip drivers and other functionality
* ux500 adds probing of some of the core SoC blocks through device
tree
* Initial device tree support for ST SPEAr600 platforms
* kirkwood continues the conversion to device-tree probing"
Manually merge arch/arm/mach-ux500/Kconfig due to MACH_U8500 rename, and
drivers/usb/gadget/at91_udc.c due to header file include cleanups.
Also do an "evil merge" for the MACH_U8500 config option rename that the
affected RMI4 touchscreen driver in staging. It's called MACH_MOP500
now, and it was missed during previous merges.
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
ARM: SPEAr600: Add device-tree support to SPEAr600 boards
ARM: ux500: Provide local timer support for Device Tree
ARM: ux500: Enable PL022 SSP Controller in Device Tree
ARM: ux500: Enable PL310 Level 2 Cache Controller in Device Tree
ARM: ux500: Enable PL011 AMBA UART Controller for Device Tree
ARM: ux500: Enable Cortex-A9 GIC (Generic Interrupt Controller) in Device Tree
ARM: ux500: db8500: list most devices in the snowball device tree
ARM: ux500: split dts file for snowball into generic part
ARM: ux500: combine the board init functions for DT boot
ARM: ux500: Initial Device Tree support for Snowball
ARM: ux500: CONFIG: Enable Device Tree support for future endeavours
ARM: kirkwood: use devicetree for rtc-mv
ARM: kirkwood: rtc-mv devicetree bindings
ARM: kirkwood: fdt: define uart[01] as disabled, enable uart0
ARM: kirkwood: fdt: facilitate new boards during fdt migration
ARM: kirkwood: fdt: absorb kirkwood_init()
ARM: kirkwood: fdt: use mrvl ticker symbol
ARM: orion: wdt: use resource vice direct access
ARM: Kirkwood: Remove tclk from kirkwood_asoc_platform_data.
ARM: orion: spi: remove enable_clock_fix which is not used
...
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=o5Xl
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: global cleanups" from Arnd Bergmann:
"Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up trivial conflicts mainly due to #include's being changes on
both sides.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
ARM: OMAP2+: Fix build error after merge
ARM: S3C24XX: remove call to s3c24xx_setup_clocks
...
Mostly a bunch of new drivers and driver bug fixes; but this also
includes a few patches that create a core message queue infrastructure
for the spi subsystem instead of making each driver open code it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=6Nsu
-----END PGP SIGNATURE-----
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull SPI changes for v3.4 from Grant Likely:
"Mostly a bunch of new drivers and driver bug fixes; but this also
includes a few patches that create a core message queue infrastructure
for the spi subsystem instead of making each driver open code it."
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
spi/fsl-espi: Make sure pm is within 2..32
spi/fsl-espi: make the clock computation easier to read
spi: sh-hspi: modify write/read method
spi: sh-hspi: control spi clock more correctly
spi: sh-hspi: convert to using core message queue
spi: s3c64xx: Fix build
spi: s3c64xx: remove unnecessary callback msg->complete
spi: remove redundant variable assignment
spi: release lock on error path in spi_pump_messages()
spi: Compatibility with direction which is used in samsung DMA operation
spi-topcliff-pch: add recovery processing in case wait-event timeout
spi-topcliff-pch: supports a spi mode setup and bit order setup by IO control
spi-topcliff-pch: Fix issue for transmitting over 4KByte
spi-topcliff-pch: Modify pci-bus number dynamically to get DMA device info
spi/imx: simplify error handling to free gpios
spi: Convert to DEFINE_PCI_DEVICE_TABLE
spi: add Broadcom BCM63xx SPI controller driver
SPI: add CSR SiRFprimaII SPI controller driver
spi-topcliff-pch: fix -Wuninitialized warning
spi: Mark spi_register_board_info() __devinit
...
Add inline wrappers for device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to hide new parameter from current users of affected interfaces.
Convert current users to use new wrappers instead of direct calls.
Suggested by Russell King [https://lkml.org/lkml/2012/2/3/269].
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
* 'kirkwood_dt_for_3.4_v3' of git://git.infradead.org/users/jcooper/linux-kirkwood:
ARM: kirkwood: use devicetree for rtc-mv
ARM: kirkwood: rtc-mv devicetree bindings
ARM: kirkwood: fdt: define uart[01] as disabled, enable uart0
ARM: kirkwood: fdt: facilitate new boards during fdt migration
ARM: kirkwood: fdt: absorb kirkwood_init()
ARM: kirkwood: fdt: use mrvl ticker symbol
ARM: orion: wdt: use resource vice direct access
ARM: Kirkwood: Remove tclk from kirkwood_asoc_platform_data.
ARM: orion: spi: remove enable_clock_fix which is not used
The reference manual says that pm has to stay within 2 and 32. So the
lowest frequency is 32 and DIV16 set, the highest is 2 and DIV16 unset.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The -1 +1 thingy should probably do what DIV_ROUND_UP does. The 4 is 2
the "platform_clock => sysclock" and 2 from the computation part. The 64
is the same 4 times 16.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'ep93xx-for-arm-soc' of git://github.com/RyanMallon/linux-2.6:
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
(update to v3.3-rc7)
Conflicts:
arch/arm/mach-s3c2440/common.h
Current sh-hspi had wrong write/read method which was not linux standard.
If spi_transfer requests tx[2], rx[2] len=2,
then, driver should run tx[0], rx[0], tx[1], rx[1].
But current sh-hspi runs tx[0], tx[1], rx[0], rx[1].
This patch fixes it up.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Current sh-hspi had used platform-specific speed.
This patch remove it, and use spi_transfer specific speed.
It removes unnecessary flags from struct sh_hspi_info,
but struct sh_hspi_info is still exist, since sh-hspi needs
platform info in the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit 054ebc (spi: Compatibility with direction which is used in samsung
DMA operation) does not build as one hunk adds a brace to the first branch
of an if statement without adding at least the correspoding close. Remove
the unwanted brace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
msg->complete will be called in spi_finalize_current_message().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The status variable is guaranteed to be 0 at that location anyway.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We should release the lock here and enable IRQs before returning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[grant.likely: move unlock above dev_err() call]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
I found that there are two kind of direction type.
First one is dma_data_direction defined in include/linux/dma-direction.h.
It is used for parameter of dma_map/unmap_single in spi-s3c64xx.
The other one is dma_transter_direction defined in include/linux/dmaengine.h.
It is used for direction of samsung DMA operation
(arch/arm/plat-samsung/dma-ops.c).
This patch is just some changes to use direction defines
which is used in samsung DMA operation.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Kyoungil Kim <ki0351.kim@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently, pch_spi_start_transfer failure is not anticipated.
This patch adds the processing.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch supports a spi mode setup and bit order setup by IO control.
spi mode: mode 0 to mode 3
bit order: LSB first, MSB first
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently, when spi-topcliff-pch receives transmit request over 4KByte,
this driver can't process correctly. This driver needs to divide the data
into 4Kbyte unit.
This patch fixes the issue.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Simplify the error handling by moving the code to free gpios in one place.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Convert static struct pci_device_id *[] to static DEFINE_PCI_DEVICE_TABLE
tables.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds support for the SPI controller found on the Broadcom BCM63xx
SoCs.
Signed-off-by: Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CSR SiRFprimaII has two SPIs (SPI0 and SPI1). Features:
* Master and slave modes
* 8-/12-/16-/32-bit data unit
* 256 bytes receive data FIFO and 256 bytes transmit data FIFO
* Multi-unit frame
* Configurable SPI_EN (chip select pin) active state
* Configurable SPI_CLK polarity
* Configurable SPI_CLK phase
* Configurable MSB/LSB first
Signed-off-by: Zhiwu Song <zhiwu.song@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix for:
drivers/spi/spi-topcliff-pch.c: In function ‘pch_spi_handler_sub’:
drivers/spi/spi-topcliff-pch.c:325:17: warning: ‘bpw_len’ may be
used uninitialized in this function [-Wuninitialized]
drivers/spi/spi-topcliff-pch.c:325:42: warning: ‘rx_index’ may be
used uninitialized in this function [-Wuninitialized]
drivers/spi/spi-topcliff-pch.c:325:42: warning: ‘tx_index’ may be
used uninitialized in this function [-Wuninitialized]
Move usage of tx_index, rx_index and bpw_len into the same
block as where they are set to prevent uninitialized usage.
v2: instead of init variables with 0 move the whole block
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some systems have SPI devices located on plugin modules which are
enumerated at runtime as devices. The drivers for these plugin modules
need to register their SPI devices at probe() time so want to be able
to call spi_register_board_info() but that function is currently marked
as __init rather than __devinit so this usage isn't legal. Change the
annotation to __devinit to handle this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Convert the s3c64xx driver to using the new message queue factored out of
the pl022 driver by Linus Walleij, saving us a nice block of code and
getting the benefits of improvements implemented in the core.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
