There was 2 muxed I2C adapters, one for demod tuner bus and one for
internal use. Idea of internal I2C adapter was to force I2C repeater
close when demod access its registers. Driver has also delayed work
queue based method to close I2C repeater.
After regmap conversion internal I2C adapter based repeater close
left unused - only work queue method was in use. We could not use
internal mux adapter method with regmap as it makes recursive regmap
call, which causes deadlock as regmap has own locking. Due to that
remove whole method totally.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We are consumer of DVB frontend provided by rtl28xxu module. Due to
that we must use refcount to ensure none could remove rtl28xxu when
we are alive (or when we are streaming, if more fine-grained
refcounting is wanted).
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Put demod to soft reset in order to save power when sleep. That drops
power usage ~30mA @5V on USB dongle I tested. In real life it does
not matter much as USB IF powers off demod too, but now it is done
twice - demod and USB IF.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I have implemented tons of things for that driver, more than anyone
else, so lets claim copyright and module authorship.
Cc: Thomas Mair <thomas.mair86@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove all the stuff that is not needed anymore. Rename variable.
Remove extra new lines.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Pass correct device, platform device, for logging system in order
to format printouts correctly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
That SDR driver module was abusing DVB frontend SEC (satellite
equipment controller) device and due to that it was also using
legacy DVB binding. Platform bus is pseudo-bus provided by kernel
driver model and it fits cases like that, where any other busses
are not suitable.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
'dev' sounds better than 's' for such variable.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Provide register read and write callbacks for SDR module.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Chips uses 8-bit register addresses with 5 pages. Extend register
address by using register page as a first byte of address, defining
virtual register addresses. That is common method of handling
register pages and regmap also uses it. Remove page + address
conversion glue which was there for regmap.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to do software reset on init() as it is done a bit
later on end of set_frontend(). Software reset usually means
restarting (resetting to starting point) chip internal state machine
(FSM). Naturally it is done after all parameters are programmed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Enable regmap register cache in order to reduce IO.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Demod lock flags are derived from demod state machine states. States
are running from 1 to 11, where highest state 11 means demod is
fully locked and streaming. Naturally smaller state numbers means
there is some partial locks.
Define now state 10 as missing synch and lock.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We don't need it anymore as all users are using muxed I2C adapter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Estimate signal strength from IF digital AGC.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move all needed configuration values to platform data structure
and remove old configuration code where possible.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename it device state variable to dev. Both priv and dev are very
common terms for such variable in kernel, but I like use dev in
order to keep drivers consistent.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Exported resources are not needed anymore as all users are using
callbacks carried via platform data. Due to that we will remove
those.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add callback for all of those functions which are currently
exported using EXPORT_SYMBOL. That allows us convert every user to
callbacks and eventually all exported symbols could be removed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Own I2C locking is needed due to two special reasons:
1) Chips uses multiple register pages/banks on single I2C slave.
Page is changed via I2C register access.
2) Chip offers muxed/gated I2C adapter for tuner. Gate/mux is
controlled by I2C register access.
Due to these reasons, I2C locking did not fit very well.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Trivial changes proposed by checkpatch.pl and some more.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove internal config and use configuration values directly from
the platform data.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Pass correct device for dev_foo() logging in order to print logs
correctly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As a I2C driver struct i2c_client is top level structure representing
the driver. Use it as parameter to carry all needed information for
each function in order to simplify things.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use name 'dev' for device state instance as it is more common and
also one letter shorter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove legacy DVB binding as all users are using I2C binding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert driver to kernel I2C model. Old DVB proprietary model is
still left there also.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
X-Patchwork-Delegate: m.chehab@samsung.com
As shown at the code, upd_demod_gain_period is used to write
to two 16-bit registers:
dib8000_write_word(state, 1946, upd_demod_gain_period & 0xFFFF);
dib8000_write_word(state, 1947, reg | (1<<14) | ((upd_demod_gain_period >> 16) & 0xFF));
So, it should be declared as u32.
This fixes the following smatch warning:
drivers/media/dvb-frontends/dib8000.c:1282 dib8000_agc_startup() warn: right shifting more than type allows
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename firmware variable from fw_file to fw_name and change its type
from u8 to const char as request_firmware() input defines.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Print chip version once using log level into when init() is called.
Remove cold/warm state printing as those are not very useful.
old printing:
si2168 6-0064: found a 'Silicon Labs Si2168' in cold state
si2168 6-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
si2168 6-0064: firmware version: 4.0.11
si2168 6-0064: found a 'Silicon Labs Si2168' in warm state
new printing:
si2168 6-0064: found a 'Silicon Labs Si2168-B40'
si2168 6-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
si2168 6-0064: firmware version: 4.0.11
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
commit 034e1ec0ce
si2168: One function call less in si2168_init() after error detection
That commit added goto label for error path to release firmware,
but forgets to remove variable NULL set. Remove those now.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All known old firmware firmware formats are downloaded using 8 byte
chunks. Reject firmware if it could not be divided to 8 byte chunks
and because of that we could simplify some calculations. Now both
supported firmware download routines are rather similar.
Cc: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use own label for kzalloc failure in which does not call kfree().
kfree() could be called with NULL, but it is still better to have
own label which skips unnecessary kfree().
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change formatter from signed to unsigned as stream_id is 32bit
unsigned variable.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Even firmware version is not needed to know, it is still interesting
and useful to know some cases. Due to that increase its printing to
info log level.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename some goto labels and more. No functionality changes.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove if () from firmware command error path as there should not be
any error prone conditional logic there. Use goto labels instead.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We don't need that anymore as same pointer is passed to each
routine via struct dvb_frontend private field.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Carry struct i2c_client pointer inside struct dvb_frontend private
pointer. This driver is I2C driver, which is represented as a
struct i2c_client, so better to carry this top level structure for
each routine in order to unify things. This allows further
simplification.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
'dev' is most common name in kernel for structure containing device
state instance, so rename it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
w_scan complains about missing symbol rate limits:
This dvb driver is *buggy*: the symbol rate limits are undefined - please report to linuxtv.org
Chip supports 1 to 7.2 MSymbol/s on DVB-C.
Cc: stable@vger.kernel.org
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for controlling TP clock mode for VSB and QAM annex-B/C mode.
Gated clock mode is the default value, and does not support QAM annex-C.
The patch enables setting this control to fixed clock mode.
Signed-off-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Simplify the code a little bit by removing some uneeded arguments
to lgdt3305_mpeg_mode_polarity().
Signed-off-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert that driver to I2C driver model.
Legacy DVB binding is left also for later removal...
Tested-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
To be future-proof and for better readability the time comparisons are
modified to use time_after() instead of plain, error-prone math.
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The debug parameter is not used anymore, as this module was
converted already to use dev_dbg().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Increase si2168 cmd execute timeout to prevent firmware load failures. Tests
shows it takes up to 52ms to load the 'dvb-demod-si2168-a30-01.fw' firmware.
Increase timeout to a safe value of 70ms.
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add xtal as a configuration parameter so it can be used
in the IF register value calculation.
Signed-off-by: Benjamin Larsson <benjamin@southpole.se>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/hd29l2.c:29:18: warning: Variable length array is used.
drivers/media/dvb-frontends/hd29l2.c:34:32: error: cannot size expression
drivers/media/dvb-frontends/hd29l2.c:125:5: warning: symbol 'hd29l2_rd_reg_mask' was not declared. Should it be static?
Variable length arrays are frowned upon, so replace with a fixed length and check
that there won't be a buffer overrun.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
1) This is not allowed by the kernel coding style
2) Just configure your editor correctly
3) It's really ugly
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As pointed by smatch:
drivers/media/dvb-frontends/stv090x.c:2787 stv090x_optimize_carloop() error: buffer overflow 'car_loop_apsk_low' 11 <= 13
drivers/media/dvb-frontends/stv090x.c:2789 stv090x_optimize_carloop() error: buffer overflow 'car_loop_apsk_low' 11 <= 13
drivers/media/dvb-frontends/stv090x.c:2791 stv090x_optimize_carloop() error: buffer overflow 'car_loop_apsk_low' 11 <= 13
drivers/media/dvb-frontends/stv090x.c:2793 stv090x_optimize_carloop() error: buffer overflow 'car_loop_apsk_low' 11 <= 13
drivers/media/dvb-frontends/stv090x.c:2795 stv090x_optimize_carloop() error: buffer overflow 'car_loop_apsk_low' 11 <= 13
The situation of a buffer overflow won't happen, in practice,
with the current values of car_loop table. Yet, the entire logic
that checks for those registration values is too complex. So,
better to add an explicit check, just in case someone changes
the car_loop tables causing a buffer overflow by mistake.
This also helps to remove several smatch warnings, with is good.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
if STV090x_RANGEOK is not returned, then STV090x_OUTOFRANGE
is returned. However, that part of the code is never reached,
as pointed by smatch:
drivers/media/dvb-frontends/stv090x.c:2673 stv090x_get_sig_params() info: ignoring unreachable code.
So, remove the two uneeded elses, with makes the code a little bit
cleaner.
No functional changes, and one less smatch warning.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While writing changeset fdf1bc9fa2, I noticed some checkpatch
complains about the CodingStyle for function parameters. So,
clean them.
While here, also removes uneeded "extern" from function prototype.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for new type of firmware versions of Si2168 chip.
Old type: n x 8 bytes (all data, first byte seems to be 04 or 05)
New type: n x 17 bytes (1 byte indicates len and max 16 bytes data)
New version of TechnoTrend CT2-4400 drivers
(http://www.tt-downloads.de/bda-treiber_4.3.0.0.zip) contains newer
firmware for Si2168-B40 that is in the new format. It can be extracted
with the following command:
dd if=ttTVStick4400_64.sys ibs=1 skip=323872 count=6919 of=dvb-demod-si2168-b40-01.fw
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A debug printout for firmware version.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Drivers that use dvb_attach can have just one exported symbol,
or they will cause compilation breakages depending on the
selected frontends.
As Jim reported:
drivers/built-in.o: In function `technisat_usb2_set_voltage':
technisat-usb2.c:(.text+0x3b4919): undefined reference to `stv090x_set_gpio'
make: *** [vmlinux] Error 1
That happens because, on his configuration, the configuration
is:
CONFIG_DVB_USB=y
CONFIG_DVB_STV090x=m
Luis proposed ar way to fix, but that would just force the
STV090x to be selected, even if one wants to use a device
with a different frontend.
Instead, let's do the right thing: move set_gpio to the
configuration structure and fill it during dvb_attach().
This way, the driver can still call it, and dvb_attach()
will load stv090x module only if the device really needs it.
Reported by: Jim Davis <jim.epost@gmail.com>
Cc: Luis Rodriguez <mcgrof@suse.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Recent rtl28xxu patch I made moved demod ADC enable from power control
to frontend control (due to slave demod support). Because of that we
need call USB interface frontend control too in order to enable ADC.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
GIT_AUTHOR_DATE=1416472767
The release_firmware() function was called in some cases by the
si2168_init() function during error handling even if the passed variable
contained still a null pointer. This implementation detail could be improved
by the introduction of another jump label.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
GIT_AUTHOR_DATE=1416472158
The release_firmware() function was called in some cases by the
m88ds3103_init() function during error handling even if the passed variable
contained still a null pointer. This implementation detail could be improved
by the introduction of another jump label.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
GIT_AUTHOR_DATE=1416472432
The release_firmware() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement partial PIP mode to carry TS from slave demodulator,
through that master demodulator. RTL2832 demod has TS input
interface to connected another demodulator TS output.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is not ready enough to be released on mainline.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert driver to I2C RegMap API. That offers unified register
access routines, register value caching and more.
We need 3 register maps, one for each register page, as chips has
3 I2C address.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Driver was using DVB proprietary binding model. As it is I2C
device, we could change it to normal kernel I2C driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Separate IF and BW based registers.
Add support for DVB-T and DVB-T2 6MHz channel bandwidth.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is not ready enough to be released on mainline.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement initial support for DVB-T and DVB-T2 modes. Now driver has
basic support for all the modes, DVB-C/T/T2.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It uses I2C bus so better to implement it as a standard I2C driver
model. It was using proprietary DVB binding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Original plan was to implement driver as one file per used demod
standard (mn88472_c.c, mn88472_t.c and mn88472_t2.c). However, that
plan was a mistake as driver code differences are so small between
different standards. Due to that rename this file and implement all
the needed functionality to that file.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
400ms delay seems to be enough in order to gain DVB-C lock.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Wrong symbol name causes demod attach failure.
Reported-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Only DVB-C mode is supported, DVB-T and DVB-T2 are not supported.
Very much feature reduced version, no signal statistics nor normal
chip configuration options.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
1> When m88ds3103 works in serial ts mode, its serial ts clock is equal to ts master clock and the clock divider is bypassed.
2> The serial ts clock is configed by the bridge driver just like parallel ts clock.
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Needed due to some important regression fixes at RC core.
* commit 'v3.18-rc4': (587 commits)
Linux 3.18-rc4
ARM: dts: zynq: Enable PL clocks for Parallella
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
i2c: core: Dispose OF IRQ mapping at client removal time
i2c: at91: don't account as iowait
i2c: remove FSF address
USB: Update default usb-storage delay_use value in kernel-parameters.txt
sysfs: driver core: Fix glue dir race condition by gdp_mutex
MIPS: Fix build with binutils 2.24.51+
xfs: track bulkstat progress by agino
xfs: bulkstat error handling is broken
xfs: bulkstat main loop logic is a mess
xfs: bulkstat chunk-formatter has issues
xfs: bulkstat chunk formatting cursor is broken
xfs: bulkstat btree walk doesn't terminate
mm: Fix comment before truncate_setsize()
USB: cdc-acm: add quirk for control-line state requests
tty: Fix pty master poll() after slave closes v2
MIPS: R3000: Fix debug output for Virtual page number
...
Conflicts:
drivers/media/rc/rc-main.c
move the return to happen before the logic. This way, we can
avoid one extra identation.
This also fixes an identation issue on this function.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is hard to read what's there, because it doesn't follow the
CodingStyle.
Add missing whitespaces to split function arguments.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is actually a false positive:
drivers/media/dvb-frontends/cx24110.c:210 cx24110_set_fec() error: buffer overflow 'rate' 7 <= 8
But fixing it is easy: just ensure that the table size will be
limited to FEC_AUTO.
While here, fix spacing on the affected lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by spatch:
drivers/media/dvb-frontends/stb0899_drv.c:720 stb0899_send_diseqc_msg() error: buffer overflow 'cmd->msg' 6 <= 7
The buffer size is 6 and not 8. Anyway, the best is to use sizeof(),
to avoid such mistakes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As sparse complains:
drivers/media/dvb-frontends/stv090x.c:3471:30: warning: mixing different enum types
drivers/media/dvb-frontends/stv090x.c:3471:30: int enum fe_delivery_system versus
drivers/media/dvb-frontends/stv090x.c:3471:30: int enum stv090x_delsys
There's actually an error when setting the delivery system on
stv090x_search(): it is using the DVBv5 macros as if they were
the stv090x ones.
Instead, we should convert between the two namespaces, returning
an error if an unsupported delivery system is requested.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
That case is not IO error, so better to jump out now, but still
continue polling.
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previous patch changed both AF9030 and IT9130 SNR reporting from
dB to relative. Restore AF9030 to old behavior as it has been always
returning 0.1 dB value. Leave IT9130 relative as old IT9130 was
returning relative values.
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Snr returns value not correct. Fix it.
Signed-off-by: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Check return status after each register access routine and avoid
masking return status values.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previous patch changes used signal strength firmware register from
0x800048 to 0x80004a in case of AF9033/AF9035 chip. In practice
reported values were running upside-down, when RR strength increases
reported value decreases and vice versa. That is because of 0x80004a
returns values that are dBm scale, but negative RF strength dBm
returned as positive number.
0x800048 returns 0-100, like percentage
0x80004a returns 0-255 dBm, without a negative sign
So restore old measurement now.
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Register 0x800048 is not dB measure but relative scale. Fix it and conform to NorDig specifications.
Signed-off-by: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It repeated "found a 'Silicon Labs Si2168' in warm state" everytime
when device was opened. Message is aimed to point out firmware is
downloaded, up and running. So print it only in case firmware download
is performed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/sp2.c:269:5: sparse: symbol 'sp2_init' was not declared. Should it be static?
drivers/media/dvb-frontends/sp2.c:351:5: sparse: symbol 'sp2_exit' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
M88RS6000 is the integrated chip, which includes tuner and demod. Its
internal demod is similar with M88DS3103 except some registers
definition.
The main different part of this internal demod from others is its
clock/pll generation IP block sitting inside the tuner die. So clock/pll
functions should be configed through its tuner i2c bus, NOT its demod
i2c bus.
The demod of M88RS6000 need the firmware: dvb-demod-m88rs6000.fw
firmware download link:
http://www.dvbsky.net/download/linux/dvbsky-firmware.tar.gz
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This code is needlessly complicated and checkpatch.pl complains that we
go over the 80 characters per line limit.
If we flip the "if (!lock) {" test to "if (lock) return;" then we can
remove an indent level from the rest of the function.
We can add two returns in the "if (state->srate >= 10000000) {"
condition and move the else statement back an additional indent level.
There is another "if (!lock) {" check which can be removed since we have
already checked "lock" and know it is zero at this point. This second
check on "lock" is also a problem because it sets off a static checker
warning. I have reviewed this code for some time to see if something
else was intended, but have concluded that it was simply an oversight
and should be removed. Removing this duplicative check gains us an
third indent level.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Improves lock performance with signals from the ZeeVee family
of modulators.
Signed-off-by: Richard Vollkommer <linux@hauppauge.com>
Cc: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Tevii S480 outputs 18V on startup for the LNB supply voltage and does not
automatically power down. This blocks other receivers connected
to a satellite channel router (EN50494), since the receivers can not send the
required DiSEqC sequences when the Tevii card is connected to a the same SCR.
This patch switches off the LNB supply voltage on initialization of the frontend.
[mchehab@osg.samsung.com: add a comment about why we're explicitly
turning off voltage at device init]
Cc: stable@vger.kernel.org
Signed-off-by: Ulrich Eckhardt <uli@uli-eckhardt.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Incorrect struct used in the SP2 driver.
Reported-by: Max Nibble <nibble.max@gmail.com>
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch partially reverts 0fb220f2a5. What happened is
that the conversion of debug messages to use pr_debug() was a
bad idea, because one needing to debug would need to both
enable debug level via a modprobe parameter, and then to
enable the dynamic printk's.
So, for now, let's use printk() directly at dprintk().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
dib7000p is for DVB, and not ISDB. So, there's no layer.
That removes this compilation warning:
drivers/media/dvb-frontends/dib7000p.c:1972: warning: 'i' is used uninitialized in this function
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DUbD
-----END PGP SIGNATURE-----
Merge tag 'media/v3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new IR driver: hix5hd2-ir
- the virtual test driver (vivi) was replaced by vivid, with has an
almost complete set of features to emulate most v4l2 devices and
properly test all sorts of userspace apps
- the as102 driver had several bugs fixed and was properly split into a
frontend and a core driver. With that, it got promoted from staging
into mainstream
- one new CI driver got added for CIMaX SP2/SP2HF (sp2 driver)
- one new frontend driver for Toshiba ISDB-T/ISDB-S demod (tc90522)
- one new PCI driver for ISDB-T/ISDB-S (pt3 driver)
- saa7134 driver got support for go7007-based devices
- added a new PCI driver for Techwell 68xx chipsets (tw68)
- a new platform driver was added (coda)
- new tuner drivers: mxl301rf and qm1d1c0042
- a new DVB USB driver was added for DVBSky S860 & similar devices
- added a new SDR driver (hackrf)
- usbtv got audio support
- several platform drivers are now compiled with COMPILE_TEST
- a series of compiler fixup patches, making sparse/spatch happier with
the media stuff and removing several warnings, especially on those
platform drivers that didn't use to compile on x86
- Support for several new modern devices got added
- lots of other fixes, improvements and cleanups
* tag 'media/v3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (544 commits)
[media] ir-hix5hd2: fix build on c6x arch
[media] pt3: fix DTV FE I2C driver load error paths
Revert "[media] media: em28xx - remove reset_resume interface"
[media] exynos4-is: fix some warnings when compiling on arm64
[media] usb drivers: use %zu instead of %zd
[media] pci drivers: use %zu instead of %zd
[media] dvb-frontends: use %zu instead of %zd
[media] s5p-mfc: Fix several printk warnings
[media] s5p_mfc_opr: Fix warnings
[media] ti-vpe: Fix typecast
[media] s3c-camif: fix dma_addr_t printks
[media] s5p_mfc_opr_v6: get rid of warnings when compiled with 64 bits
[media] s5p_mfc_opr_v5: Fix lots of warnings on x86_64
[media] em28xx: Fix identation
[media] drxd: remove a dead code
[media] saa7146: remove return after BUG()
[media] cx88: remove return after BUG()
[media] cx88: fix cards table CodingStyle
[media] radio-sf16fmr2: declare some structs as static
[media] radio-sf16fmi: declare pnp_attached as static
...
cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
drivers/media/dvb-frontends/drxd_hard.c:2839 drxd_init() info: ignoring unreachable code.
Firmware request/release is not at drxd_init. So, we can remove
that dead code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
PLP selection was implemented for Si2168 last month (patchwork 25387). However, FE_CAN_MULTISTREAM was not added to dvb_frontend_ops of si2168. This patch adds FE_CAN_MULTISTREAM, which indicates that multiple PLP are supported.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/built-in.o: In function `tc90522t_get_frontend':
>> tc90522.c:(.text+0x260b64c): undefined reference to `__divdi3'
>> tc90522.c:(.text+0x260b685): undefined reference to `__divdi3'
>> tc90522.c:(.text+0x260b6bb): undefined reference to `__divdi3'
>> tc90522.c:(.text+0x260b713): undefined reference to `__divdi3'
drivers/built-in.o:tc90522.c:(.text+0x260bb64): more undefined references to `__divdi3' follow
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/tc90522.c:706:5: warning: symbol 'tc90522_functionality' was not declared. Should it be static?
drivers/media/dvb-frontends/tc90522.c:706:5: warning: no previous prototype for 'tc90522_functionality' [-Wmissing-prototypes]
u32 tc90522_functionality(struct i2c_adapter *adap)
^
Cc: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds driver for tc90522 demodulator chips.
The chip contains 4 demod modules that run in parallel and are independently
controllable via separate I2C addresses.
Two of the modules are for ISDB-T and the rest for ISDB-S.
It is used in earthsoft pt3 cards.
Note that this driver does not init the chip,
because the initilization sequence / register setting is not disclosed.
Thus, the driver assumes that the chips are initilized externally
by its parent board driver before fe->ops->init() are called.
Earthsoft PT3 PCIe card, for example, contains the init sequence
in its private memory and provides a command to trigger the sequence.
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
"len" is user controlled and can be up to 255. Anything more than 59
will cause a buffer overflow so we need to add a test for that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Additionally print chip name with revision symbolically.
This is a preparation for supporting new Hauppauge WinTV-HVR-900-H based
on cx231xx.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Current firmware is only for revision D.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
cab_state->modulation is initialized with a wrong value:
drivers/media/dvb-frontends/stv0367.c:3000:42: warning: mixing different enum types
drivers/media/dvb-frontends/stv0367.c:3000:42: int enum fe_modulation versus
drivers/media/dvb-frontends/stv0367.c:3000:42: int enum stv0367cab_mod
as it was declared as "enum stv0367cab_mod". While it could be fixed,
there's no value on it, as this is never used.
So, just remove the modulation from cab_state structure.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It was using the wrong constant for QAM256 on get_frontend.
Signed-off-by: Maks Naumov <maksqwe1@ukr.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Just returns whatever error that was returned by the i2c core,
in the case of errors, only returning -EREMOTEIO if the transfer size
is not what it was expected.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The returned code is 0, 1 or an error. It doesn't make sense to
print it in hexadecimal.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need to init supported stats here in order signal app which
stats are supported.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Statistics are now calculated for DVBv5 and those DVBv5 values are
returned for legacy DVBv3 calls also. So we could remove all old
statistics calculation logic.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
DVBv5 BER is calculated anyway, so just return it for legacy
read_ber() API too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement following DTV API commands:
DTV_STAT_POST_ERROR_BIT_COUNT
DTV_STAT_POST_TOTAL_BIT_COUNT
These will provide post-Viterbi bit error rate reporting.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement following API commands:
DTV_STAT_ERROR_BLOCK_COUNT
DTV_STAT_TOTAL_BLOCK_COUNT
These returns total and uncorrected error packets from outer FEC.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Let the demod firmware estimate RF signal strength and return it
to the app as a dBm. To handle that, use thread which reads signal
strengths from firmware in 2 sec intervals when device is active.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I2C driver address is passed as a i2c_new_device() parameter when
device is created. Thus no need to keep it in config struct.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It uses I2C client so logging system prints module name
automatically. Function name is also added automatically, if it is
requested from dynamic debug by setting proper format.
Because of that, we could simplify logging in our driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
foo_dev seems to be most correct term for the structure holding data
of each device instance. It is most used term in Kernel codebase and also
examples from book Linux Device Drivers, Third Edition, uses it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
AF9030 and IT9130 series has different memory location for firmware
version. Choose correct location according to chip type.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
AF903x/IT913x demod provides clock source(s). It seems that this
clock source is used for integrated RF tuner of IT913x. It is
enabled by default, but firmware disables it automatically when
suspend is requested (suspend_flag (0x004c) + trigger_ofsm
(0x0000)). Automatic disable behavior seems to be similar for both
AF903x and IT913x I tested, though there is no likely any real
clock user in a case of AF903x.
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a variable to keep track if firmware is loaded or not and skip parts of the
initialization if fw is already loaded. Resume from sleep with a different
command compared to initial power up and run command 85 after resume command.
This behaviour is observed when using manufacturer provided binary-only si2168
driver for TechnoTrend CT2-4400.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove function name from debug logs. Logging system could add it
automatically.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sample rate calculation gives a little bit too large results because
in real life there was around one milliseconds (~one usb packet) too
much data for given time. Calculate time more accurate in order to
provide better results.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to init flags before calling spin_lock_irqsave().
spin_lock_irqsave is macro which stores value to 'flags'
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are some patches that depends on media-v3.16-rc6.
So, merge back from upstream before applying them.
* linus/master: (1123 commits)
drm/nouveau: ltc/gf100-: fix cbc issues on certain boards
drm/bochs: add missing drm_connector_register call
drm/cirrus: add missing drm_connector_register call
staging: vt6655: buffer overflow in ioctl
USB: storage: Add quirks for Entrega/Xircom USB to SCSI converters
USB: storage: Add quirk for Ariston Technologies iConnect USB to SCSI adapter
USB: storage: Add quirk for Adaptec USBConnect 2000 USB-to-SCSI Adapter
USB: EHCI: unlink QHs even after the controller has stopped
[SCSI] fix for bidi use after free
[SCSI] fix regression that accidentally disabled block-based tcq
[SCSI] libiscsi: fix potential buffer overrun in __iscsi_conn_send_pdu
drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
drm/nouveau/runpm: fix module unload
drm/radeon/px: fix module unload
vgaswitcheroo: add vga_switcheroo_fini_domain_pm_ops
drm/radeon: don't reset dma on r6xx-evergreen init
drm/radeon: don't reset sdma on CIK init
drm/radeon: don't reset dma on NI/SI init
drm/radeon/dpm: fix resume on mullins
drm/radeon: Disable HDP flush before every CS again for < r600
...
this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.
Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
IT9135 RF tuner clock is coming from demodulator. We need enable it
early in demod init, before any tuner I/O. Currently it is enabled
by tuner driver itself, but it is too late and performance will be
reduced as some registers are not updated correctly. Clock is
disabled automatically when demod is put onto sleep.
Cc: <stable@vger.kernel.org> # v3.15+
Cc: Bimow Chen <Bimow.Chen@ite.com.tw>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drxk_hard.c:2224:3-22: code aligned with following code on line 2227
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by cocinelle:
drivers/media/dvb-frontends/drxd_hard.c:2632:3-51: code aligned with following code on line 2633
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by cocinelle:
drivers/media/dvb-frontends/sp8870.c:395:2-14: code aligned with following code on line 397
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
instead of testing if it is false or true, just use
if (!foo) or if (foo). That makes the code easier to
read and shorter.
Also, properly initialize booleans with true or false.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of using 0 or 1 for boolean, use the true/false
defines.
Also, instead of testing foo == false, just use the
simplified notation if(!foo).
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The error return code STV0900_NO_ERROR happens only once, at
the end of the functions. So, just return it directly.
This driver should actually be fixed to return standard
Linux error codes, instead of its own macros, but this
should be done on a separate patchset.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/stv0367.c:557:5: warning: symbol 'stv0367cab_RF_LookUp1' was not declared. Should it be static?
drivers/media/dvb-frontends/stv0367.c:569:5: warning: symbol 'stv0367cab_RF_LookUp2' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/mb86a16.c:31:14: warning: symbol 'verbose' was not declared. Should it be static?
drivers/media/dvb-frontends/mb86a20s.c:36:4: warning: symbol 'mb86a20s_subchannel' was not declared. Should it be static?
drivers/media/dvb-frontends/mb86a20s.c:1333:24: warning: symbol 'cnr_qpsk_table' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/dib7000p.c:2562:5: warning: symbol 'dib7090_set_diversity_in' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add some error checking and implement functionality a little bit
differently.
Cc: Nibble Max <nibble.max@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver for the CIMaX SP2 common interface chip. It is very much based on
the existing cimax2 driver for cx23885, but should be more reusable. The
product has been sold with name Atmel T90FJR as well and the data sheets
for that chip seem to be publicly available.
It seems that the USB device that I have and the cx23885 based devices will
need to interact differently with the chip for the CAM operations. Thus
there is one callback function that is passed on to the sp2 driver
(see function sp2_ci_op_cam for that one).
IRQ functionality is not included currently (not needed by USB devices
and I don't have a PCIe device for development).
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Luis Alves submitted a TS mode patch to si2168 earlier, but the
patch was rejected due to a small issue. Here is a working version.
Also, setting of TS mode is moved from si2168_set_frontend to
si2168_init.
This patch adds the TS mode as a config option for the si2168 demod:
- ts_mode added to config struct.
- Possible (interesting) values are
* Parallel mode = 0x06
* Serial mode = 0x03
Currently the modules using this demod only use parallel mode.
Patches for these modules later in this patch series.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement set voltage operation.
Separate TS clock as a own configuration parameter.
Add TS clock polarity parameter.
[crope@iki.fi: merge em28xx driver m88ds3103 config change patch
to that one, in order to keep build unbroken]
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Same thing for si2168 as Antti did earlier for tda18212:
There is no need to print module name nor function name as those
are done by kernel logging system when dev_xxx logging is used and
driver is proper I2C driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In order to get FE_HAS_SYNC, the viterbi should already be
locked too. So, add the missing FE_HAS_VITERBI lock.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by Kbuildtest:
In file included from drivers/media/usb/cx231xx/cx231xx-dvb.c:35:0:
drivers/media/dvb-frontends/si2165.h:57:9: warning: 'struct si2165_config' declared inside parameter list [enabled by default]
struct i2c_adapter *i2c)
^
drivers/media/dvb-frontends/si2165.h:57:9: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:157:21: error: variable 'hauppauge_930C_HD_1113xx_si2165_config' has initializer but incomplete type
static const struct si2165_config hauppauge_930C_HD_1113xx_si2165_config = {
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:158:2: error: unknown field 'i2c_addr' specified in initializer
.i2c_addr = 0x64,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:158:2: warning: excess elements in struct initializer [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:158:2: warning: (near initialization for 'hauppauge_930C_HD_1113xx_si2165_config') [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:159:2: error: unknown field 'chip_mode' specified in initializer
.chip_mode = SI2165_MODE_PLL_XTAL,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:159:15: error: 'SI2165_MODE_PLL_XTAL' undeclared here (not in a function)
.chip_mode = SI2165_MODE_PLL_XTAL,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:159:2: warning: excess elements in struct initializer [enabled by default]
.chip_mode = SI2165_MODE_PLL_XTAL,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:159:2: warning: (near initialization for 'hauppauge_930C_HD_1113xx_si2165_config') [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:160:2: error: unknown field 'ref_freq_Hz' specified in initializer
.ref_freq_Hz = 16000000,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:160:2: warning: excess elements in struct initializer [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:160:2: warning: (near initialization for 'hauppauge_930C_HD_1113xx_si2165_config') [enabled by default]
>> drivers/media/usb/cx231xx/cx231xx-dvb.c:163:21: error: variable 'pctv_quatro_stick_1114xx_si2165_config' has initializer but incomplete type
static const struct si2165_config pctv_quatro_stick_1114xx_si2165_config = {
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:164:2: error: unknown field 'i2c_addr' specified in initializer
.i2c_addr = 0x64,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:164:2: warning: excess elements in struct initializer [enabled by default]
>> drivers/media/usb/cx231xx/cx231xx-dvb.c:164:2: warning: (near initialization for 'pctv_quatro_stick_1114xx_si2165_config') [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:165:2: error: unknown field 'chip_mode' specified in initializer
.chip_mode = SI2165_MODE_PLL_EXT,
^
>> drivers/media/usb/cx231xx/cx231xx-dvb.c:165:15: error: 'SI2165_MODE_PLL_EXT' undeclared here (not in a function)
.chip_mode = SI2165_MODE_PLL_EXT,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:165:2: warning: excess elements in struct initializer [enabled by default]
.chip_mode = SI2165_MODE_PLL_EXT,
^
>> drivers/media/usb/cx231xx/cx231xx-dvb.c:165:2: warning: (near initialization for 'pctv_quatro_stick_1114xx_si2165_config') [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c:166:2: error: unknown field 'ref_freq_Hz' specified in initializer
.ref_freq_Hz = 24000000,
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:166:2: warning: excess elements in struct initializer [enabled by default]
>> drivers/media/usb/cx231xx/cx231xx-dvb.c:166:2: warning: (near initialization for 'pctv_quatro_stick_1114xx_si2165_config') [enabled by default]
drivers/media/usb/cx231xx/cx231xx-dvb.c: In function 'dvb_init':
drivers/media/usb/cx231xx/cx231xx-dvb.c:731:3: warning: passing argument 1 of 'si2165_attach' from incompatible pointer type [enabled by default]
dev->dvb->frontend = dvb_attach(si2165_attach,
^
In file included from drivers/media/usb/cx231xx/cx231xx-dvb.c:35:0:
drivers/media/dvb-frontends/si2165.h:55:36: note: expected 'const struct si2165_config *' but argument is of type 'const struct si2165_config *'
static inline struct dvb_frontend *si2165_attach(
^
drivers/media/usb/cx231xx/cx231xx-dvb.c:764:3: warning: passing argument 1 of 'si2165_attach' from incompatible pointer type [enabled by default]
dev->dvb->frontend = dvb_attach(si2165_attach,
^
In file included from drivers/media/usb/cx231xx/cx231xx-dvb.c:35:0:
drivers/media/dvb-frontends/si2165.h:55:36: note: expected 'const struct si2165_config *' but argument is of type 'const struct si2165_config *'
static inline struct dvb_frontend *si2165_attach(
^
That happens because the frontend was disabled by .config, but the
si2165_attach void stub require those structs, and also the
drivers that call it.
While here, remove the duplicated info about the possible I2C
addresses.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DVB-T was tested with 8MHz BW channels in germany
This driver is the simplest possible, it uses automatic mode for all
parameters (TPS).
Added spectrum inversion support.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Tested-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drx39xxj_set_lna() and drx39xxj_set_frontend() set LNA. Instead of
duplicating LNA configure code, change to use drxj_set_lna_state()
which sets LNA to the caller requested state (on or off).
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Several functions ignore the return values in error legs and always
return -EIO. This makes it hard to debug and take proper action in
calling routines.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drx39xyj driver lacks resume support. Add support by changing
its fe ops init interface to detect the resume status by checking
fe exit flag and do the necessary initialization. With this change,
driver resume correctly in both dvb adapter is not in use and in use
by an application cases.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Change drx39xyj_release() to check fe exit flag to detect the
device disconnect state and avoid accessing the device after
it has been removed.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fixes error:
[next:master 7435/8702] ERROR: "usb_alloc_urb
[drivers/media/dvb-frontends/rtl2832_sdr.ko] undefined!
rtl2832_sdr driver implements own USB streaming for SDR data.
Logically that functionality belongs to USB interface driver, but
currently it is implemented here.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch removes the null test on ch. ch is initialized at the
beginning of the function to &demod->dtv_property_cache. Since demod
is dereferenced prior to the null test, demod must be a valid pointer,
and &demod->dtv_property_cache cannot be null.
The following Coccinelle script is used for detecting the change:
@r@
expression e,f;
identifier g,y;
statement S1,S2;
@@
*e = &f->g
<+...
f->y
...+>
*if (e != NULL || ...)
S1 else S2
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of looking at the guard interval field, it was using
the interval length, with is wrong. Fix it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Interleaving code was wrong at mb86a20s: instead, it was looking
at the Guard Interval. Fix it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver was reporting an incorrect mode, when mode 2
is selected.
While testing it, noticed that neither mode 1 or guard
interval 1/32 is supported by this device. Document it,
and ensure that it will report _AUTO when it doesn't lock,
in order to not report a wrong detection to userspace.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There was 32-bit calculation overflow. Use div_u64.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This cleans up some line over 80 character violations.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This removes checks of struct member addresses since they likely result
in the condition always being true. Also in the stb6100_get_bandwidth
and tda8261_get_bandwidth functions the pointers frontend_ops and
tuner_ops are assigned the same addresses twice.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This updated patch also fixes out of bound access to b[].
In dib9000_risc_apb_access_write() an out of bound access to mb[].
The current test to avoid out of bound access to mb[] is insufficient.
For len = 19 non-existent mb[10] will be accessed.
For odd values of len b[] is accessed out of bounds.
For large values of len an of bound access to mb[] may occur in
dib9000_mbx_send_attr.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
>From the context this should be hex 0x80 instead of decimal 80.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
changeset a733291d69 didn't merge the fixes well. It ended by
restoring some bad logic removed there.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* .: (268 commits)
Linux 3.16-rc6
um: segv: Save regs only in case of a kernel mode fault
um: Fix hung task in fix_range_common()
um: Ensure that a stub page cannot get unmapped
Revert "um: Fix wait_stub_done() error handling"
btrfs: test for valid bdev before kobj removal in btrfs_rm_device
Btrfs: fix abnormal long waiting in fsync
random: check for increase of entropy_count because of signed conversion
ARM: EXYNOS: Fix core ID used by platsmp and hotplug code
ahci: add support for the Promise FastTrak TX8660 SATA HBA (ahci mode)
ARM: at91/dt: add missing clocks property to pwm node in sam9x5.dtsi
ARM: at91/dt: fix usb0 clocks definition in sam9n12 dtsi
ARM: at91: at91sam9x5: correct typo error for ohci clock
irqchip: gic: Fix core ID calculation when topology is read from DT
GFS2: fs/gfs2/rgrp.c: kernel-doc warning fixes
GFS2: memcontrol: Spelling s/invlidate/invalidate/
GFS2: Allow caching of glocks for flock
GFS2: Allow flocks to use normal glock dq rather than dq_wait
GFS2: replace count*size kzalloc by kcalloc
GFS2: Use GFP_NOFS when allocating glocks
...
Conflicts:
drivers/media/dvb-frontends/si2168.c
drivers/media/dvb-frontends/si2168_priv.h
drivers/media/tuners/si2157.c
MEDIA_SDR_SUPPORT and I2C_MUX are needed for rtl2832_sdr.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 0ba2aeb6da
(v4l2-ctrls: increase internal min/max/step/def to 64 bit)
changes v4l2 controls to 64-bit. Driver it not working on 32-bit
arch as it uses directly control 'step' which is changed to 64-bit.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fill FMT buffer size field in order to inform app which will be
used streaming buffer size. Currently driver doesn't allow buffer
size value proposed by application.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Testing demod presence on probe fails if the demod was sleep mode.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In case of failure the return value was always 0. Return proper
error code (ENODEV) instead.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Improve scanning performance by setting property 0301 with a value
from Windows driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds symbol rate setting to the driver.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
SDR API is very new and surprises may occur. Due to that print
notice to remind possible users.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move emulated format behind module parameter as those are not
supported. Format conversions will be on library eventually.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rework firmware selection logic a little bit.
Print notice asking user update firmware when old Si2168 B40
firmware is used.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Tested-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver uses that new firmware too, so advertise it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Tested-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add handling for different chip revisions and firmwares.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Command 0x14 returns 4 bytes as a reply. It is used for setting
key/value pairs to firmware and it returns 4 bytes back including
old value.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No need to set explicitly value that are already defaulted same.
Setting new value returns old value. Firmware default values can
be found just looking returned value.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Same command was executed twice, but different value. Remove
redundant command.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use memcpy for set cmd buffer in order to keep style in line with
rest of file.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Detected symbol rate value was returned too small.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Inversion ON was reported as inversion OFF and vice versa.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
FEC AUTO is valid for PSK-8 modulation too. Add it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Only supported modulation for DVB-S is QPSK. Modulation parameter
contains invalid value for DVB-S on some cases, which leads driver
refusing tuning attempt. Due to that, hard code modulation to QPSK
in case of DVB-S.
Cc: stable@vger.kernel.org
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The message is currently highly encoded:
[70299.863521] DiB8000: Mpeg locks [ L0 : 0 | L1 : 1 | L2 : 0 ]
And doesn't properly reflect that some problems might have happened.
Instead, display it as:
[75160.822321] DiB8000: Not all ISDB-T layers locked in 32 ms: Layer A NOT LOCKED, Layer B locked, Layer C not enabled
In order to better reflect what's happening with layer locking.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When debug is enabled:
- Report when frontend gets restarted;
- Be coherent on the displayed lines;
- Show the transmission mode;
- Hide unused layers.
No functional changes (except at the printk's).
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This table doesn't match the new one.
Update it.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of doing the tuning delays and timeouts using
current_kernel_time(), use jiffies. That consumes less
CPU cycles, and it is monotonic.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
msleep() is not too precise: its precision depends on the
HZ config. As the driver selects precise timings for the
state machine, change it to usleep_range().
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
msleep() is not too precise: its precision depends on the
HZ config. As the driver selects precise timings for the
state machine, change it to usleep_range().
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Just like the Windows driver, restart SAD during reset
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
TV broadcasters generally use partial reception. So, enable it by
default in auto-search mode. The driver will latter detect if the
transmission is on some other mode.
Acked-By: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Antti Palosaari
Mauro Carvalho Chehab
Michael Ira Krufky
Asaf Vertz
Jurgen Kramer
Benjamin Larsson
Hans Verkuil
Olli Salonen
Geert Uytterhoeven
Markus Elfring
CrazyCat
nibble.max
Bimow Chen
Fengguang Wu
Akihiro Tsukada
Dan Carpenter
Richard Vollkommer
ほち
Ulrich Eckhardt
Linus Torvalds
Matthias Schwarzott
Maks Naumov
Hans Wennborg
Andrey Utkin
Hans Verkuil
abdoulaye berthe
Mauro Carvalho Chehab
Shuah Khan
Himangi Saraogi
Fabian Frederick
Emil Goode
Heinrich Schuchardt
Luis Alves