Commit Graph

255 Commits

Author SHA1 Message Date
Mohammed Habibulla 1fb4e09a7e Bluetooth: Add support for Lite-on [04ca:3007]
Add support for the AR9462 chip

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=03 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3007 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Mohammed Habibulla <moch@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2014-04-25 09:47:16 +03:00
Marcel Holtmann 3c49aa852e Revert "Bluetooth: Enable autosuspend for Intel Bluetooth device"
This reverts commit d2bee8fb6e.

Enabling autosuspend for Intel Bluetooth devices has been shown to not
work reliable. It does work for some people with certain combinations
of USB host controllers, but for others it puts the device to sleep and
it will not wake up for any event.

These events can be important ones like HCI Inquiry Complete or HCI
Connection Request. The events will arrive as soon as you poke the
device with a new command, but that is not something we can do in
these cases.

Initially there were patches to the xHCI USB controller that fixed
this for some people, but not for all. This could be well a problem
somewhere in the USB subsystem or in the USB host controllers or
just plain a hardware issue somewhere. At this moment we just do
not know and the only safe action is to revert this patch.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Tedd Ho-Jeong An <tedd.an@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2014-04-25 09:47:15 +03:00
Peng Chen ca58e594da Bluetooth: Add a new PID/VID 0cf3/e005 for AR3012.
usb devices info:

T:  Bus=06 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 13 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e005 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Peng Chen <pengchen@qca.qualcomm.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-03-05 20:52:17 +02:00
Andy Shevchenko a735f9e224 Bluetooth: append new supported device to the list [0b05:17d0]
The device found on Asus Z87 Expert motherboard requires firmware to work
correctly.

T:  Bus=03 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0b05 ProdID=17d0 Rev=00.02
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-02-18 09:54:20 -08:00
Andy Shevchenko 0b8800623d Bluetooth: sort the list of IDs in the source code
This will help to manage table of supported IDs.

There is no functional change.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-02-18 09:54:20 -08:00
Jurgen Kramer 9113bfd82d Bluetooth: btusb: Add IMC Networks (Broadcom based)
Add support for IMC Networks (Broadcom based) to btusb driver.

Below the output of /sys/kernel/debug/usb/devices for this device:

T:  Bus=01 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3404 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=240A649F8246
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-02-15 11:51:03 -08:00
Oliver Neukum 1e56f1eb2b Bluetooth: Add firmware update for Atheros 0cf3:311f
The device is not functional without firmware.

The device without firmware:
T:  Bus=02 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=311f Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

The device with firmware:
T:  Bus=02 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=3007 Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-02-13 09:51:36 +02:00
Oliver Neukum b131237ca3 Bluetooth: Enable Atheros 0cf3:311e for firmware upload
The device will bind to btusb without firmware, but with the original
buggy firmware device discovery does not work. No devices are detected.

Device descriptor without firmware:
T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=311e Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

with firmware:
T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=311e Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2014-02-13 09:51:36 +02:00
John W. Linville 300e5fd160 Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next 2014-01-08 13:44:29 -05:00
John W. Linville 9d1cd503c7 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless 2014-01-06 14:08:41 -05:00
Marcel Holtmann 81cac64ba2 Bluetooth: Deal with USB devices that are faking CSR vendor
There exists a set of Bluetooth USB devices that show up on the USB
bus as 0a12:0001 and identify themselves as devices from CSR. However
they are not. When sending Read Local Version command they now have
a split personality and say they are from Broadcom.

  < HCI Command: Read Local Version Information (0x04|0x0001) plen 0
  > HCI Event: Command Complete (0x0e) plen 12
      Read Local Version Information (0x04|0x0001) ncmd 1
      status 0x00
      HCI Version: 2.0 (0x3) HCI Revision: 0x3000
      LMP Version: 2.0 (0x3) LMP Subversion: 0x420b
      Manufacturer: Broadcom Corporation (15)

The assumption is that they are neither CSR nor Broadcom based devices
and that they are designed and manufactured by someone else.

For the most parts they follow the Bluetooth HCI specification and
can be used as standard Bluetooth devices. However they have the
minor problem that the Delete Stored Link Key command is not working
as it should.

During the Bluetooth controller setup, this command is needed if
stored link keys are supported. For these devices it has to be
assumed that this is broken and so just set a quirk to clearly
indicate the behavior. After that the setup can just proceed.

Now the trick part is to detect these faulty devices since we do
not want to punish all CSR and all Broadcom devices. The original
devices do actually work according to the specification.

What is known so far is that these broken devices set the USB bcdDevice
revision information to 1.0 or less.

T:  Bus=02 Lev=01 Prnt=01 Port=08 Cnt=03 Dev#=  9 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0a12 ProdID=0001 Rev= 1.00
S:  Manufacturer=Bluetooth v2.0
S:  Product=Bluetooth V2.0 Dongle

T:  Bus=05 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0a12 ProdID=0001 Rev= 0.07

In case of CSR devices, the bcdDevice revision contains the firmware
build ID and that is normally a higher value. If the bcdDevice revision
is 1.0 or less, then an extra setup stage is checking if Read Local
Version returns CSR manufacturer information. If not then it will be
assumed that this is a broken device and the Delete Stored Link Key
command will be marked as broken.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2014-01-04 20:11:07 +02:00
Marco Piazza bd0976dd33 Bluetooth: Add support for Toshiba Bluetooth device [0930:0220]
This patch adds support for new Toshiba Bluetooth device.

T:  Bus=05 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0930 ProdID=0220 Rev=00.02
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: Marco Piazza <mpiazza@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-12-04 11:11:49 -02:00
Tedd Ho-Jeong An d2bee8fb6e Bluetooth: Enable autosuspend for Intel Bluetooth device
This patch enables autosuspend for Intel Bluetooth device.

After btusb is loaded for Intel Bluetooth device, the power/control
attribute contains "on" value by default which disables the autosuspend.
Based on the USB PM document(Documentation/usb/power-management.txt),
kernel disabled the autosuspend for all devices other than hub by default.

"The USB specification states that all USB devices must support power
management.  Nevertheless, the sad fact is that many devices do not
support it very well.  You can suspend them all right, but when you
try to resume them they disconnect themselves from the USB bus or
they stop working entirely.  This seems to be especially prevalent
among printers and scanners, but plenty of other types of device have
the same deficiency.

For this reason, by default the kernel disables autosuspend (the
power/control attribute is initialized to "on") for all devices other
than hubs.  Hubs, at least, appear to be reasonably well-behaved in
this regard."

This document also described how the driver can enables the autosuspend
by using an USB api.

"Drivers can enable autosuspend for their devices by calling

	usb_enable_autosuspend(struct usb_device *udev);

in their probe() routine, if they know that the device is capable of
suspending and resuming correctly.  This is exactly equivalent to
writing "auto" to the device's power/control attribute."

For Intel Bluetooth device, the autosuspend needs to be enabled so the
device can transit to LPM(Low Power Mode) and ULPM(Ultra LPM) states after
receiving suspend message from the host.

Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-12-04 11:09:05 -02:00
Tedd Ho-Jeong An ef4e5e4a75 Bluetooth: Add support for Intel Bluetooth device [8087:0a2a]
This patch adds support for new Intel Bluetooth device.

T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=8087 ProdID=0a2a Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-12-04 11:09:04 -02:00
Sujith Manoharan 35580d223b Bluetooth: ath3k: Add support for a new AR3012 device
T:  Bus=02 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#=  9 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e05f Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Reported-by: Joshua Richenhagen <richenhagen@gmail.com>
Signed-off-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-12-04 11:09:04 -02:00
Sujith Manoharan bd0fca1b2b Bluetooth: ath3k: Add support for another AR3012 card
T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=300b Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Reported-by: Face <falazemi@gmail.com>
Signed-off-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2013-12-04 11:09:04 -02:00
John W. Linville 6b732323c1 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth 2013-11-05 15:58:21 -05:00
Marcel Holtmann 54265202f1 Bluetooth: Declare btusb_table[] and blacklist_table[] as const
The btusb_table[] and blacklist_table[] USB device tables can be
declared as const.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11 17:05:18 +02:00
Marcel Holtmann 7bd8f09f69 Bluetooth: Add hdev parameter to hdev->send driver callback
Instead of masking hdev inside the skb->dev parameter, hand it
directly to the driver as a parameter to hdev->send. This makes
the driver interface more clear and simpler.

This patch fixes all drivers to accept and handle the new parameter
of hdev->send callback. Special care has been taken for bpa10x
and btusb drivers that require having skb->dev set to hdev for
the URB transmit complete handlers.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-11 15:28:03 +02:00
Marcel Holtmann 014f7bc787 Bluetooth: Use hci_conn_num() instead of direct connection hash access
When changing the alternate setting for the ISOC endpoints, use the
hci_conn_num() helper function to count currently established SCO
and eSCO connections and store the the value. This avoids direct
access to the connection hash.

In addition use the stored value instead accessing the connection
hash over and over again.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-10-10 22:08:02 +02:00
Hans de Goede b1a8014471 Bluetooth: revert: "Bluetooth: Add missing reset_resume dev_pm_ops"
Many btusb devices have 2 modes, a hid mode and a bluetooth hci mode. These
devices default to hid mode for BIOS use. This means that after having been
reset they will revert to HID mode, and are no longer usable as a HCI.

Therefor it is a very bad idea to just blindly make reset_resume point to
the regular resume handler. Note that the btusb driver has no clue how to
switch these devices from hid to hci mode, this is done in userspace through
udev rules, so the proper way to deal with this is to not have a reset-resume
handler and instead let the usb-system re-enumerate the device, and re-run
the udev rules.

I must also note, that the commit message for the commit causing this
problem has a very weak motivation for the change:

"Add missing reset_resume dev_pm_ops. Missing reset_resume results in the
following message after power management device test. This change sets
reset_resume to btusb_resume().

[ 2506.936134] btusb 1-1.5:1.0: no reset_resume for driver btusb?
[ 2506.936137] btusb 1-1.5:1.1: no reset_resume for driver btusb?"

Making a change solely to silence a warning while also changing important
behavior (normal resume handling versus re-enumeration) requires a commit
message with a proper explanation why it is safe to do so, which clearly lacks
here, and unsurprisingly it turns out to not be safe to make this change.

Reverting the commit in question fixes bt no longer working on my Dell
E6430 after a suspend/resume, and I believe it likely also fixes the
following bugs:
https://bugzilla.redhat.com/show_bug.cgi?id=988481
https://bugzilla.redhat.com/show_bug.cgi?id=1010649
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1213239

This reverts commit 502f769662.

Cc: Shuah Khan <shuah.kh@samsung.com>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-10-02 16:01:49 -03:00
Ken O'Brien 5bcecf3253 Bluetooth: btusb: Add support for Belkin F8065bf
Add generic rule on encountering Belkin bluetooth usb device F8065bf.

Relevant section from /sys/kernel/debug/usb/devices:

T:  Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=050d ProdID=065a Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=0002723E2D29
C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms

Signed-off-by: Ken O'Brien <kernel@kenobrien.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-09-23 17:44:25 -03:00
Raphael Kubo da Costa 38a172bef8 Bluetooth: Add support for BCM20702A0 [0b05, 17cb]
Yet another vendor specific ID for this chipset; this one for the ASUS
USB-BT400 Bluetooth 4.0 adapter.

T:  Bus=03 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#=  6 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0b05 ProdID=17cb Rev=01.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=000272C64400
C:  #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Cc: stable@vger.kernel.org
Signed-off-by: Raphael Kubo da Costa <rakuco@FreeBSD.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-09-16 14:36:56 -03:00
Peng Chen 0a3658cccd Bluetooth: Add a new PID/VID 0cf3/e005 for AR3012.
usb device info:

T:  Bus=06 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 15 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e005 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms

Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Peng Chen <pengchen@qca.qualcomm.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-09-16 14:36:55 -03:00
John W. Linville 704278ccb5 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Conflicts:
	net/bluetooth/hci_core.c
2013-07-31 15:11:50 -04:00
AceLan Kao 1d5b569ef8 Bluetooth: Add support for Atheros [0cf3:e003]
Add support for the AR9462 chip

T:  Bus=02 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e003 Rev=00.02
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Cc: Stable <stable@vger.kernel.org>
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-07-25 19:52:37 +01:00
AceLan Kao 1ebd0b21ab Bluetooth: Add support for Atheros [0cf3:3121]
Add support for the AR3012 chip.

T:  Bus=03 Lev=01 Prnt=01 Port=06 Cnt=01 Dev#=  6 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=3121 Rev=00.02
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-07-25 19:52:35 +01:00
Sujith Manoharan 5b77a1f3d7 Bluetooth: ath3k: Add support for ID 0x13d3/0x3402
T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  5 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3402 Rev= 0.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=59701

Signed-off-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-07-25 19:52:34 +01:00
Adam Lee d9c78e9738 Bluetooth: fix wrong use of PTR_ERR() in btusb
PTR_ERR() returns a signed long type value which is limited by IS_ERR(),
it must be a negative number whose range is [-MAX_ERRNO, 0).

The bug here returns negative numbers as error codes, then check it by
"if (ret < 0)", but -PTR_ERR() is actually positive. The wrong use here
leads to failure as below, even panic.

[   12.958920] Bluetooth: hci0 command 0xfc8e tx timeout
[   14.961765] Bluetooth: hci0 command 0xfc8e tx timeout
[   16.964688] Bluetooth: hci0 command 0xfc8e tx timeout
[   20.954501] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[   22.957358] Bluetooth: hci0 command 0xfc8e tx timeout
[   30.948922] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[   32.951780] Bluetooth: hci0 command 0xfc8e tx timeout
[   40.943359] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[   42.946219] Bluetooth: hci0 command 0xfc8e tx timeout
[   50.937812] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[   52.940670] Bluetooth: hci0 command 0xfc8e tx timeout
[   60.932236] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[   62.935092] Bluetooth: hci0 command 0xfc8e tx timeout
[   70.926688] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[   72.929545] Bluetooth: hci0 command 0xfc8e tx timeout
[   80.921111] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[   82.923969] Bluetooth: hci0 command 0xfc2f tx timeout
[   90.915542] Bluetooth: hci0 sending Intel patch command (0xfc2f) failed (-110)
[   92.918406] Bluetooth: hci0 command 0xfc11 tx timeout
[  100.909955] Bluetooth: hci0 sending Intel patch command (0xfc11) failed (-110)
[  102.912858] Bluetooth: hci0 command 0xfc60 tx timeout
[  110.904394] Bluetooth: hci0 sending Intel patch command (0xfc60) failed (-110)
[  112.907293] Bluetooth: hci0 command 0xfc11 tx timeout
[  120.898831] Bluetooth: hci0 exiting Intel manufacturer mode failed (-110)
[  120.904757] bluetoothd[1030]: segfault at 4 ip 00007f8b2eb55236 sp 00007fff53ff6920 error 4 in bluetoothd[7f8b2eaff000+cb000]

Signed-off-by: Adam Lee <adam.lee@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-07-25 19:52:33 +01:00
Thomas Loo 84eb2ae180 Bluetooth: ath3k: Add support for Fujitsu Lifebook UH5x2 [04c5:1330]
The Fujitsu Lifebook UH552/UH572 ships with a Qualcomm AR9462/AR3012
WLAN/BT-Combo card.
Add device ID to the ath3k driver to enable the bluetooth side of things.
Patch against v3.10.

T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04c5 ProdID=1330 Rev=00.02
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: Thomas Loo <tloo@saltstorm.net>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-07-25 19:52:31 +01:00
Shuah Khan 502f769662 Bluetooth: Add missing reset_resume dev_pm_ops
Add missing reset_resume dev_pm_ops. Missing reset_resume results in the
following message after power management device test. This change sets
reset_resume to btusb_resume().

[ 2506.936134] btusb 1-1.5:1.0: no reset_resume for driver btusb?
[ 2506.936137] btusb 1-1.5:1.1: no reset_resume for driver btusb?

Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-06-23 00:23:53 +01:00
Cho, Yu-Chen 178c059e76 Bluetooth: Add support for Mediatek Bluetooth device [0e8d:763f]
This patch adds support for Mediatek Bluetooth device

T:  Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.01 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0e8d ProdID=763f Rev= 1.00
S:  Manufacturer=MediaTek
S:  Product=BT
S:  SerialNumber=1.0
C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=450mA
A:  FirstIf#= 0 IfCount= 2 Cls=ff(vend.) Sub=ff Prot=ff
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms

Signed-off-by: Cho, Yu-Chen <acho@suse.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-13 13:32:28 -04:00
Tedd Ho-Jeong An dffd30ee96 Bluetooth: Add support for Intel Bluetooth device [8087:07dc]
This patch adds support for Intel Bluetooth device by adding
btusb_setup_intel() routine that update the device with ROM patch.

T:  Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=8087 ProdID=07dc Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-04-23 20:27:48 -03:00
Marcel Holtmann 9f8f962c85 Bluetooth: Use separate function for BCM92035 vendor setup
Trying to squeeze every single vendor setup routine into the same function
and have it assigned all the time is actually a bad idea. Especially since
the core can handle the absence of a setup routine perfectly fine.

To make this a lot simpler for future additions of vendor setup code,
split the BCM92035 setup into its own function and only assign it when
this specific device has been detected.

Doing it like this has the nice side benefit that we do not have to keep
a copy of the driver_info around.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-04-11 16:34:10 -03:00
Marcel Holtmann 9360099764 Bluetooth: Convert BCM92035 support to driver setup callback
With the early init stage during setup, this quirk can be simplified
and kept fully inside the driver.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2013-04-04 19:28:10 +03:00
Noguchi Kazutosi 0fc110f4e4 Bluetooth: Add support for Foxconn/Hon Hai [0489:e04d]
Add support for the AR3012 chip.

T:  Bus=01 Lev=02 Prnt=02 Port=05 Cnt=03 Dev#= 21 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e04d Rev=00.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: Noguchi Kazutosi <linux@scaltinof.net>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-04-04 11:12:32 +03:00
Ming Lei ebaf5795ef Bluetooth: Add support for Dell[QCA 0cf3:817a]
Add support for the AR9462 chip

T:  Bus=03 Lev=01 Prnt=01 Port=08 Cnt=01 Dev#=  5 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=817a Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Cc: <stable@vger.kernel.org>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-03-18 14:14:37 -03:00
Ming Lei d66629c132 Bluetooth: Add support for Dell[QCA 0cf3:0036]
Add support for the AR9462 chip

T:  Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=0036 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Cc: <stable@vger.kernel.org>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-03-15 14:11:32 -03:00
Sunguk Lee 94a32d10f4 Bluetooth: Device 0cf3:3008 should map AR 3012
T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=3008 Rev= 0.01
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Sunguk Lee <d3m3vilurr@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-03-11 18:04:54 -03:00
Josh Boyer 3f63c340a7 Bluetooth: Add support for atheros 04ca:3004 device to ath3k
Yet another version of the atheros bluetooth chipset

T:  Bus=01 Lev=02 Prnt=02 Port=03 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3004 Rev=00.01
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

This resolves https://bugzilla.redhat.com/show_bug.cgi?id=844750

Reported-by: niktr@mail.ru
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-02-20 14:23:08 -03:00
Sergio Cambra f4d6f7dce7 Bluetooth device 04ca:3008 should use ath3k
Output of /sys/kernel/debug/usb/devices
T:  Bus=03 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  6 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3008 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Sergio Cambra <sergio@programatica.es>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-01-10 02:51:03 -02:00
AceLan Kao 2582d529c4 Bluetooth: Add support for Foxconn / Hon Hai [0489:e056]
Add support for the AR9462 chip

T: Bus=01 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e056 Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-01-09 17:05:15 -02:00
AceLan Kao 3a61eda81e Bluetooth: Add support for Foxconn / Hon Hai [0489:e04e]
Add support for the AR9462 chip

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e04e Rev=00.02
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-01-09 17:05:15 -02:00
Daniel Schaal 2c262b2a52 Bluetooth: Add support for GC-WB300D PCIe [04ca:3006] to ath3k.
T:  Bus=02 Lev=02 Prnt=02 Port=06 Cnt=01 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3006 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Daniel Schaal <farbing@web.de>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-01-09 17:05:14 -02:00
AceLan Kao eed307e290 Bluetooth: Add support for IMC Networks [13d3:3393]
Add support for the AR9462 chip

T:  Bus=02 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3393 Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2013-01-09 17:05:14 -02:00
John W. Linville d2ff5ee919 Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next 2012-11-21 13:03:00 -05:00
Jeff Cook 1ee3ff6110 Bluetooth: Add support for BCM20702A0 [0b05, 17b5]
Vendor-specific ID for BCM20702A0.
Support for bluetooth over Asus Wi-Fi GO!, included with Asus P8Z77-V
Deluxe.

T:  Bus=07 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0b05 ProdID=17b5 Rev=01.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=94DBC98AC113
C:  #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Cc: stable@vger.kernel.org
Signed-off-by: Jeff Cook <jeff@deserettechnology.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-11-19 19:52:23 -02:00
Marcos Chaparro acd9454433 Bluetooth: ath3k: Add support for VAIO VPCEH [0489:e027]
Added Atheros AR3011 internal bluetooth device found in Sony VAIO VPCEH to the
devices list.
Before this, the bluetooth module was identified as an Foxconn / Hai bluetooth
device [0489:e027], now it claims to be an AtherosAR3011 Bluetooth
[0cf3:3005].

T:  Bus=01 Lev=02 Prnt=02 Port=04 Cnt=02 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e027 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Marcos Chaparro <marcos@mrkindustries.com.ar>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-11-09 16:45:37 +01:00
John W. Linville 791ef39cd1 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next 2012-09-24 14:39:16 -04:00
Jaroslav Resler 0c1abbd1aa Bluetooth: Add support for BCM20702A0 [04ca, 2003]
Add another vendor specific ID for BCM20702A0.

output of usb-devices:
T:  Bus=01 Lev=02 Prnt=02 Port=03 Cnt=02 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=2003 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=446D57861623
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Signed-off-by: Cho, Yu-Chen <acho@suse.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-09-18 22:27:31 -03:00
Gustavo Padovan ee66401bb9 Bluetooth: Add USB_VENDOR_AND_INTERFACE_INFO() for Broadcom/Foxconn
Foxconn devices has a vendor specific class of device, we will match them
differently now.

Cc: stable@vger.kernel.org
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-09-18 22:27:30 -03:00
John W. Linville fac805f8c1 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless 2012-09-07 15:07:55 -04:00
Henrik Rydberg 1fa6535faf Bluetooth: Add support for Apple vendor-specific devices
As pointed out by Gustavo and Marcel, all Apple-specific Broadcom
devices seen so far have the same interface class, subclass and
protocol numbers. This patch adds an entry which matches all of them,
using the new USB_VENDOR_AND_INTERFACE_INFO() macro.

In particular, this patch adds support for the MacBook Pro Retina
(05ac:8286), which is not in the present list.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Shea Levy <shea@shealevy.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-08-27 08:36:42 -05:00
Gustavo Padovan 92c385f46b Bluetooth: Use USB_VENDOR_AND_INTERFACE() for Broadcom devices
Many Broadcom devices has a vendor specific devices class, with this rule
we match all existent and future controllers with this behavior.

We also remove old rules to that matches product id for Broadcom devices.

Tested-by: John Hommel <john.hommel@hp.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-08-21 14:46:44 -03:00
Yevgeniy Melnichuk bc21fde2d5 Bluetooth: Add support for Sony Vaio T-Series
Add Sony Vaio T-Series Bluetooth Module( 0x489:0xE036) to
the blacklist of btusb module and add it to the ath3k module.

output of cat /sys/kernel/debug/usb/devices

T:  Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#=  5 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e036 Rev= 0.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Yevgeniy Melnichuk <yevgeniy.melnichuk@googlemail.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-08-15 01:09:35 -03:00
Peng Chen 2096ae6ca6 Bluetooth: add support for atheros 0489:e057
Add support for the AR3012 chip found on Fioxconn.

    usb-devices shows:

    T:  Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 44 Spd=12   MxCh= 0
    D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
    P:  Vendor=0489 ProdID=e057 Rev= 0.02
    C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
    I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
    E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
    E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
    E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
    I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
    E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
    E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
    I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
    E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
    E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
    I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
    E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
    E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
    I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
    E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
    E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
    I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
    E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
    E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
    I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
    E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
    E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Peng Chen <pengchen@qca.qualcomm.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-08-06 15:33:05 -03:00
Manoj Iyer 61c964ba17 Bluetooth: btusb: Add vendor specific ID (0a5c:21f4) BCM20702A0
Patch adds support for BCM20702A0 device id (0a5c:21f4).

usb-devices after patch was applied:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21f4 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=E4D53DF154D6
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

usb-devices before patch was applied:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21f4 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=E4D53DF154D6
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Tested-by: Chris Gagnon <chris.gagnon@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-08-06 15:19:35 -03:00
Sachin Kamat 98921dbd00 Bluetooth: Use devm_kzalloc in btusb.c file
devm_kzalloc() eliminates the need to free memory explicitly
thereby saving some cleanup code.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-08-06 15:03:02 -03:00
David S. Miller e486463e82 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/usb/qmi_wwan.c
	net/batman-adv/translation-table.c
	net/ipv6/route.c

qmi_wwan.c resolution provided by Bjørn Mork.

batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.

ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-25 15:50:32 -07:00
Giancarlo Formicuccia 6c4ae5c2e7 Bluetooth: add support for atheros 0930:0219
Add support for the AR3012 chip found on the Toshiba Sallite M840-1000-XQ.

usb-devices shows:

T:  Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0930 ProdID=0219 Rev=00.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: Giancarlo Formicuccia <giancarlo.formicuccia@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-06-11 23:54:33 -03:00
Marek Vasut 6eda541d12 Bluetooth: Support AR3011 in Acer Iconia Tab W500
Acer used this chip connected via USB:

Bus 005 Device 005: ID 0cf3:3005 Atheros Communications, Inc. AR3011 Bluetooth
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass          224 Wireless
  bDeviceSubClass         1 Radio Frequency
  bDeviceProtocol         1 Bluetooth
  bMaxPacketSize0        64
  idVendor           0x0cf3 Atheros Communications, Inc.
  idProduct          0x3005 AR3011 Bluetooth
  bcdDevice            0.01
  iManufacturer           0
  iProduct                0
  iSerial                 0
  bNumConfigurations      1

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
2012-06-09 19:29:02 -03:00
Gustavo Padovan 8c520a5992 Bluetooth: Remove unnecessary headers include
Most of the include were unnecessary or already included by some other
header.
Replace module.h by export.h where possible.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2012-06-05 06:34:08 +03:00
Szymon Janc a6c511c636 Bluetooth: Rename HCI_QUIRK_NO_RESET to HCI_QUIRK_RESET_ON_CLOSE
HCI_QUIRK_NO_RESET name is misleading - purpose of this quirk is to
reset device on close instead of init, not to not reset at all.
Rename it to HCI_QUIRK_RESET_ON_CLOSE to avoid confusion.

Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2012-06-05 06:34:06 +03:00
Linus Torvalds 28f3d71761 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull more networking updates from David Miller:
 "Ok, everything from here on out will be bug fixes."

1) One final sync of wireless and bluetooth stuff from John Linville.
   These changes have all been in his tree for more than a week, and
   therefore have had the necessary -next exposure.  John was just away
   on a trip and didn't have a change to send the pull request until a
   day or two ago.

2) Put back some defines in user exposed header file areas that were
   removed during the tokenring purge.  From Stephen Hemminger and Paul
   Gortmaker.

3) A bug fix for UDP hash table allocation got lost in the pile due to
   one of those "you got it..  no I've got it.." situations.  :-)

   From Tim Bird.

4) SKB coalescing in TCP needs to have stricter checks, otherwise we'll
   try to coalesce overlapping frags and crash.  Fix from Eric Dumazet.

5) RCU routing table lookups can race with free_fib_info(), causing
   crashes when we deref the device pointers in the route.  Fix by
   releasing the net device in the RCU callback.  From Yanmin Zhang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (293 commits)
  tcp: take care of overlaps in tcp_try_coalesce()
  ipv4: fix the rcu race between free_fib_info and ip_route_output_slow
  mm: add a low limit to alloc_large_system_hash
  ipx: restore token ring define to include/linux/ipx.h
  if: restore token ring ARP type to header
  xen: do not disable netfront in dom0
  phy/micrel: Fix ID of KSZ9021
  mISDN: Add X-Tensions USB ISDN TA XC-525
  gianfar:don't add FCB length to hard_header_len
  Bluetooth: Report proper error number in disconnection
  Bluetooth: Create flags for bt_sk()
  Bluetooth: report the right security level in getsockopt
  Bluetooth: Lock the L2CAP channel when sending
  Bluetooth: Restore locking semantics when looking up L2CAP channels
  Bluetooth: Fix a redundant and problematic incoming MTU check
  Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C
  Bluetooth: Fix EIR data generation for mgmt_device_found
  Bluetooth: Fix Inquiry with RSSI event mask
  Bluetooth: improve readability of l2cap_seq_list code
  Bluetooth: Fix skb length calculation
  ...
2012-05-24 11:54:29 -07:00
Sarah Sharp e1f12eb6ba USB: Disable hub-initiated LPM for comms devices.
Hub-initiated LPM is not good for USB communications devices.  Comms
devices should be able to tell when their link can go into a lower power
state, because they know when an incoming transmission is finished.
Ideally, these devices would slam their links into a lower power state,
using the device-initiated LPM, after finishing the last packet of their
data transfer.

If we enable the idle timeouts for the parent hubs to enable
hub-initiated LPM, we will get a lot of useless LPM packets on the bus
as the devices reject LPM transitions when they're in the middle of
receiving data.  Worse, some devices might blindly accept the
hub-initiated LPM and power down their radios while they're in the
middle of receiving a transmission.

The Intel Windows folks are disabling hub-initiated LPM for all USB
communications devices under a xHCI USB 3.0 host.  In order to keep
the Linux behavior as close as possible to Windows, we need to do the
same in Linux.

Set the disable_hub_initiated_lpm flag for for all USB communications
drivers.  I know there aren't currently any USB 3.0 devices that
implement these class specifications, but we should be ready if they do.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2012-05-18 15:42:55 -07:00
Michael Gruetzner 85d59726c5 Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C
Add Foxconn/Hon Hai AR5BBU22 Bluetooth Module( 0x489:0xE03C) to
the blacklist of btusb module and add it to the ath3k module to properly
load the firmware in Kernel 3.3.4
The device is integrated in  e.g. some  Acer Aspire 7750G.

Output from /sys/kernel/debug/usb/devices:

T:  Bus=01 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#=  6 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e03c Rev= 0.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Michael Gruetzner <mgruetzn@gmx.de>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
2012-05-16 16:13:26 -03:00
Mikel Astiz f4001d2846 Bluetooth: btusb: Dynamic alternate setting
The alternate setting must be dynamically set according to the number of
active SCO links, and the bit depth of the audio. The possible values
for the alternate setting are described in the Bluetooth Core
Specification, Volume 4, Part B, section 2.1.1.

Signed-off-by: Mikel Astiz <mikel.astiz.oss@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
2012-05-09 01:40:35 -03:00
Steven Harms 985140369b Add Foxconn / Hon Hai IDs for btusb module
This change adds 0x0489:0xe033 to the btusb module.

This bluetooth usb device is integrated in the Acer TimelineX AS4830TG-6808 notebook.

Output from /sys/kernel/debug/usb/devices:

T:  Bus=01 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e033 Rev= 2.29
S:  Manufacturer=Broadcom Corp
S:  Product=Acer Module
S:  SerialNumber=60D819F74101
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  32 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  32 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Signed-off-by: Steven Harms <sjharms@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
2012-04-24 11:38:41 -03:00
AceLan Kao ac71311e65 Bluetooth: Add support for AR3012 [0cf3:e004]
Add another vendor specific ID for Atheros AR3012

output of usb-devices:
T:  Bus=02 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e004 Rev=00.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

BugLink: https://bugs.launchpad.net/bugs/922715

Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2012-04-19 11:14:06 +02:00
AceLan Kao 87522a433b Bluetooth: Add support for Atheros [13d3:3362]
Add another vendor specific ID for Atheros AR3012 device.
This chip is wrapped by IMC Networks.

output of usb-devices:
T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3362 Rev=00.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-04-13 12:59:56 +03:00
Manoj Iyer 79cd760220 Bluetooth: btusb: Add vendor specific ID (0489 e042) for BCM20702A0
T: Bus=02 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e042 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=E4D53DCA61B5
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Reported-by: Dennis Chua <dennis.chua@canonical.com>
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-04-13 12:21:38 +03:00
Don Zickus 2e8b506310 Bluetooth: btusb: typo in Broadcom SoftSailing id
I was trying to backport the following commit to RHEL-6

    From 0cea73465cd22373c5cd43a3edd25fbd4bb532ef Mon Sep 17 00:00:00 2001
    From: Oliver Neukum <oliver@neukum.org>
    Date: Wed, 21 Sep 2011 11:37:15 +0200
    Subject: [PATCH] btusb: add device entry for Broadcom SoftSailing

and noticed it wasn't working on an HP Elitebook.  Looking into the patch I
noticed a very subtle typo in the ids.  The patch has '0x05ac' instead of
'0x0a5c'.  A snippet of the lsusb -v output also shows this:

Bus 002 Device 003: ID 0a5c:21e1 Broadcom Corp.
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass          255 Vendor Specific Class
  bDeviceSubClass         1
  bDeviceProtocol         1
  bMaxPacketSize0        64
  idVendor           0x0a5c Broadcom Corp.
  idProduct          0x21e1
  bcdDevice            1.12
  iManufacturer           1 Broadcom Corp
  iProduct                2 BCM20702A0
  iSerial                 3 60D819F0338C
  bNumConfigurations      1

Looking at other Broadcom ids, the fix matches them whereas the original patch
matches Apple's ids.

Tested on an HP Elitebook 8760w.  The btusb binds and the userspace stuff loads
correctly.

Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-03-29 13:42:51 +03:00
AceLan Kao 55ed7d4d14 Bluetooth: Add support for Atheros [04ca:3005]
Add another vendor specific ID for Atheros AR3012 device.
This chip is wrapped by Lite-On Technology Corp.

output of usb-devices:
T:  Bus=04 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3005 Rev=00.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
2012-03-28 12:02:41 -03:00
Cho, Yu-Chen 07c0ea874d Bluetooth: Add Atheros maryann PIDVID support
Add Atheros maryann 0cf3:311d PIDVID support
This module is AR3012 Series.

Include /sys/kernel/debug/usb/devices output here for reference

before:
T:  Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=311d Rev= 0.01
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

after:
T:  Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=311d Rev= 0.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Cho, Yu-Chen <acho@suse.com>
cked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-03-28 12:02:28 -03:00
João Paulo Rechi Vita 6dfc326f06 Bluetooth: btusb: Add USB device ID "0a5c 21e8"
One more vendor-specific ID for BCM20702A0.

T:  Bus=01 Lev=03 Prnt=05 Port=02 Cnt=01 Dev#=  9 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0a5c ProdID=21e8 Rev=01.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=00027221F4E2
C:  #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Signed-off-by: João Paulo Rechi Vita <jprvita@openbossa.org>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-03-28 12:02:27 -03:00
Eran 9498ba7a1d Bluetooth: Adding USB device 13d3:3375 as an Atheros AR3012.
The bluetooth module in the Asus UX31/UX21 is based on Atheros AR3012
and requires a firmware to be uploaded before it's usable.

output of usb-devices for this module:
T:  Bus=01 Lev=02 Prnt=02 Port=07 Cnt=03 Dev#=  6 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3375 Rev=00.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: Eran <eran@over-here.org>
Tested-by: Michal Labedzki <michal.labedzki@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2012-03-08 02:16:24 -03:00
James M. Leddy 0a4eaeeb99 Bluetooth: btusb: add support for BCM20702A0 [0a5c:21e6]
Add another vendor specific ID for BCM20702A0.  This has been tested and
works on hardware with this device.

output of usb-devices:
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=04 Dev#= 6 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21e6 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=D0DF9AFB227B
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Signed-off-by: James M. Leddy <james.leddy@canonical.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-03-06 02:42:16 +02:00
Keng-Yu Lin 6b6ba88b5b Bluetooth: Add AR30XX device ID on Asus laptops
The ID is found on Asus K54HR and K53U.
Blacklist the AR3011-based device ID [0489:e03d]
and add to ath3k.c for firmware loading.

Below is the output of usb-devices script:

Before the fiwmware loading:

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e03d Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

After the fiwmware loading:

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=3005 Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-02-23 13:06:57 +02:00
Johan Hedberg 46479e6985 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next.git
Conflicts:
	include/net/bluetooth/l2cap.h
	net/bluetooth/hci_conn.c
	net/bluetooth/l2cap_core.c
2012-02-16 14:25:34 +02:00
Manoj Iyer 403f048a57 Bluetooth: btusb: Add vendor specific ID (0a5c 21f3) for BCM20702A0
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21f3 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=74DE2B344A7B
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Tested-by: Dennis Chua <dennis.chua@canonical.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-02-15 13:09:26 +02:00
Daniel Wagner 19ad9e94f6 Bluetooth: Don't mark non xfer isoc endpoint URBs with URB_ISO_ASAP
[ 2096.384084] btusb_send_frame:684: hci0
[ 2096.384087] usb 3-1: BOGUS urb flags, 2 --> 0
[ 2096.384091] Bluetooth: hci0 urb ffff8801b61d3a80 submission failed (22)

According the documentation in usb_submit_urb() URB_ISO_ASAP
flag is only allowed for endpoints of type USB_ENDPOINT_XFER_ISOC.

This reverts commit b8aabfc922.

Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-02-15 13:09:25 +02:00
David Herrmann 9ab875affb Bluetooth: btusb: Remove device lock on release
Recently we changed the way how we release driver-data. A driver is now
responsible of destroying the data so we no longer need the device lock
on deinitialization in btusb driver.

Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-02-13 17:01:38 +02:00
David Herrmann 155961e800 Bluetooth: Remove hci_dev->driver_data
The linux device model provides dev_set/get_drvdata so we can use this
to save private driver data.
This also removes several unnecessary casts.

Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-02-13 17:01:37 +02:00
Manoj Iyer 37305cf649 Bluetooth: btusb: Add vendor specific ID (0a5c 21f3) for BCM20702A0
T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21f3 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=74DE2B344A7B
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Tested-by: Dennis Chua <dennis.chua@canonical.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-02-13 17:01:32 +02:00
David Herrmann dc946bd86f Bluetooth: Remove __hci_dev_put/hold
Since we remove the owner field of hci_dev hci_dev_put and __hci_dev_put
do the same so we can merge them into one function. Same for
hci_dev_hold and __hci_dev_hold.

Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-02-13 17:01:24 +02:00
David Herrmann e9b9cfa157 Bluetooth: Remove HCI-owner field
After unregistering an hci_dev object a bluetooth driver does not have
any callbacks in the hci_dev structure left over. Therefore, there is no
need to keep a reference to the module.

Previously, we needed this to protect the hci-destruct callback.
However, this callback is no longer available so we do not need this
owner field, anymore.  Drivers now call hci_unregister_dev() and they
are done with the object.

Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-02-13 17:01:24 +02:00
David Herrmann 8381088e39 Bluetooth: btusb: Free driver data on USB shutdown
Instead of using the hci-destruct callback we free our private driver
data on USB shutdown. We already called hci_unregister_dev() here so the
hci core will never ever call our callbacks again except the destruct
callback.

However, there is no reason to keep our *private* driver data alive if
we get never called again and the hci-core does never touch it the data.
So we simply free it right away and set the destruct callback to NULL.

Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-02-13 17:01:23 +02:00
Daniel Wagner 5e41862322 Bluetooth: Don't mark non xfer isoc endpoint URBs with URB_ISO_ASAP
[ 2096.384084] btusb_send_frame:684: hci0
[ 2096.384087] usb 3-1: BOGUS urb flags, 2 --> 0
[ 2096.384091] Bluetooth: hci0 urb ffff8801b61d3a80 submission failed (22)

According the documentation in usb_submit_urb() URB_ISO_ASAP
flag is only allowed for endpoints of type USB_ENDPOINT_XFER_ISOC.

This reverts commit b8aabfc922.

Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2012-02-13 17:01:20 +02:00
Rusty Russell 90ab5ee941 module_param: make bool parameters really bool (drivers & misc)
module_param(bool) used to counter-intuitively take an int.  In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.

It's time to remove the int/unsigned int option.  For this version
it'll simply give a warning, but it'll break next kernel version.

Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2012-01-13 09:32:20 +10:30
Linus Torvalds 7affca3537 Merge branch 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
  arm: fix up some samsung merge sysdev conversion problems
  firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
  Drivers:hv: Fix a bug in vmbus_driver_unregister()
  driver core: remove __must_check from device_create_file
  debugfs: add missing #ifdef HAS_IOMEM
  arm: time.h: remove device.h #include
  driver-core: remove sysdev.h usage.
  clockevents: remove sysdev.h
  arm: convert sysdev_class to a regular subsystem
  arm: leds: convert sysdev_class to a regular subsystem
  kobject: remove kset_find_obj_hinted()
  m86k: gpio - convert sysdev_class to a regular subsystem
  mips: txx9_sram - convert sysdev_class to a regular subsystem
  mips: 7segled - convert sysdev_class to a regular subsystem
  sh: dma - convert sysdev_class to a regular subsystem
  sh: intc - convert sysdev_class to a regular subsystem
  power: suspend - convert sysdev_class to a regular subsystem
  power: qe_ic - convert sysdev_class to a regular subsystem
  power: cmm - convert sysdev_class to a regular subsystem
  s390: time - convert sysdev_class to a regular subsystem
  ...

Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
 - arch/arm/mach-exynos/cpu.c
 - arch/arm/mach-exynos/irq-eint.c
 - arch/arm/mach-s3c64xx/common.c
 - arch/arm/mach-s3c64xx/cpu.c
 - arch/arm/mach-s5p64x0/cpu.c
 - arch/arm/mach-s5pv210/common.c
 - arch/arm/plat-samsung/include/plat/cpu.h
 - arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
2012-01-07 12:03:30 -08:00
Greg Kroah-Hartman ff4b8a57f0 Merge branch 'driver-core-next' into Linux 3.2
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.

The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2012-01-06 11:42:52 -08:00
Jesse Sung c0190925da Bluetooth: Add support for BCM20702A0 [0a5c:21e3]
Add another vendor specific ID for BCM20702A0.

output of usb-devices:
T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21e3 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=9439E5CBF66C
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-12-22 14:20:03 -02:00
Bing Zhao fa0fb93f2a Bluetooth: btusb: fix bInterval for high/super speed isochronous endpoints
For high-speed/super-speed isochronous endpoints, the bInterval
value is used as exponent, 2^(bInterval-1). Luckily we have
usb_fill_int_urb() function that handles it correctly. So we just
call this function to fill in the RX URB.

Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-12-21 02:16:28 -02:00
Gustavo F. Padovan 5c69b0ada6 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/padovan/bluetooth 2011-12-03 08:26:25 +09:00
Cong Wang 54a8a79c55 btusb: fix a memory leak in btusb_send_frame()
This patch fixes the following memory leak reported by kmemleak:

unreferenced object 0xffff880060a53840 (size 192):
  comm "softirq", pid 0, jiffies 4320571771 (age 1406.569s)
  hex dump (first 32 bytes):
    01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff81138a1c>] create_object+0x187/0x28b
    [<ffffffff814be12e>] kmemleak_alloc+0x73/0x98
    [<ffffffff811289d3>] __kmalloc+0xfc/0x123
    [<ffffffff81386546>] usb_alloc_urb+0x1e/0x48
    [<ffffffffa0130274>] btusb_send_frame+0x86/0x385 [btusb]
    [<ffffffffa02d8230>] hci_send_frame+0xa0/0xa5 [bluetooth]
    [<ffffffffa02d8a4e>] hci_cmd_task+0xa0/0xfb [bluetooth]
    [<ffffffff81058548>] tasklet_action+0x8f/0xef
    [<ffffffff81058a4c>] __do_softirq+0xf4/0x1db
    [<ffffffff81058bb7>] run_ksoftirqd+0x84/0x129
    [<ffffffff8106f1c4>] kthread+0xa0/0xa8
    [<ffffffff814dd144>] kernel_thread_helper+0x4/0x10
    [<ffffffffffffffff>] 0xffffffffffffffff

The problem is that when inc_tx() returns non-zero, we forgot
to call usb_free_urb().

Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: "Gustavo F. Padovan" <padovan@profusion.mobi>
Signed-off-by: WANG Cong <amwang@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-12-03 08:19:59 +09:00
Greg Kroah-Hartman 93f1508cff USB: convert drivers/bluetooth/* to use module_usb_driver()
This converts the drivers in drivers/bluetooth/* to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.

Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.

Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: "Gustavo F. Padovan" <padovan@profusion.mobi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-11-18 09:47:34 -08:00
John W. Linville 312fef7d18 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/padovan/bluetooth-next
Conflicts:
	net/bluetooth/l2cap_sock.c
	net/bluetooth/mgmt.c
2011-11-09 14:54:33 -05:00
Wen-chien Jesse Sung d13431ca3e Bluetooth: Add support for Broadcom BCM20702A0
Since this device declares itself as vendor specific, must add
a new entry to device ID table to support it.

usb-device output of this device:

T:  Bus=01 Lev=02 Prnt=02 Port=03 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=413c ProdID=8197 Rev=01.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=D0DF9AA9C9F1
C:  #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-11-08 13:15:43 -02:00
Luiz Augusto von Dentz b8aabfc922 Bluetooth: use buffer priority to mark URB_ISO_ASAP flag
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-11-07 17:24:57 -02:00
Linus Torvalds 7e0bb71e75 Merge branch 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
  PM / Clocks: Remove redundant NULL checks before kfree()
  PM / Documentation: Update docs about suspend and CPU hotplug
  ACPI / PM: Add Sony VGN-FW21E to nonvs blacklist.
  ARM: mach-shmobile: sh7372 A4R support (v4)
  ARM: mach-shmobile: sh7372 A3SP support (v4)
  PM / Sleep: Mark devices involved in wakeup signaling during suspend
  PM / Hibernate: Improve performance of LZO/plain hibernation, checksum image
  PM / Hibernate: Do not initialize static and extern variables to 0
  PM / Freezer: Make fake_signal_wake_up() wake TASK_KILLABLE tasks too
  PM / Hibernate: Add resumedelay kernel param in addition to resumewait
  MAINTAINERS: Update linux-pm list address
  PM / ACPI: Blacklist Vaio VGN-FW520F machine known to require acpi_sleep=nonvs
  PM / ACPI: Blacklist Sony Vaio known to require acpi_sleep=nonvs
  PM / Hibernate: Add resumewait param to support MMC-like devices as resume file
  PM / Hibernate: Fix typo in a kerneldoc comment
  PM / Hibernate: Freeze kernel threads after preallocating memory
  PM: Update the policy on default wakeup settings
  PM / VT: Cleanup #if defined uglyness and fix compile error
  PM / Suspend: Off by one in pm_suspend()
  PM / Hibernate: Include storage keys in hibernation image on s390
  ...
2011-10-25 15:18:39 +02:00
Paul Bolle d4b8d1c9c1 Bluetooth: btusb: hide more usb_submit_urb errors
There are still three calls of usb_submit_urb() that will print errors
if those calls return -EPERM or -ENODEV. I have never triggered these,
so I'm not sure when these return values might be seen. It still makes
sense to be silent if these occur (since "urb is being killed" and
"device got disconnected" aren't things to worry about).

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-10-10 18:02:36 -03:00
Paul Bolle 5a9b80e2cd Bluetooth: btusb: also be quiet when suspending
usb_submit_urb() returns -ENODEV when a usb device is disconnected. In
commit 4935f1c164 ("Bluetooth: btusb: be
quiet on device disconnect") I stopped treating that return as an error
in the three btusb_*_complete() functions.

It turns out btusb_send_frame() generates a similar error if the system
is suspended while the bluetooth usb device is enabled. The sensible
thing to do here seems to be to treat -ENODEV (and -EPERM) just like the
btusb_*_complete() functions now do.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-10-10 18:02:31 -03:00
Rafael J. Wysocki d727b60659 Merge branch 'pm-runtime' into pm-for-linus
* pm-runtime:
  PM / Tracing: build rpm-traces.c only if CONFIG_PM_RUNTIME is set
  PM / Runtime: Replace dev_dbg() with trace_rpm_*()
  PM / Runtime: Introduce trace points for tracing rpm_* functions
  PM / Runtime: Don't run callbacks under lock for power.irq_safe set
  USB: Add wakeup info to debugging messages
  PM / Runtime: pm_runtime_idle() can be called in atomic context
  PM / Runtime: Add macro to test for runtime PM events
  PM / Runtime: Add might_sleep() to runtime PM functions
2011-10-07 23:16:55 +02:00
Oliver Neukum c510eae377 btusb: add device entry for Broadcom SoftSailing
From 0cea73465cd22373c5cd43a3edd25fbd4bb532ef Mon Sep 17 00:00:00 2001
From: Oliver Neukum <oliver@neukum.org>
Date: Wed, 21 Sep 2011 11:37:15 +0200
Subject: [PATCH] btusb: add device entry for Broadcom SoftSailing

This device declares itself to be vendor specific
It therefore needs to be added to the device table
to make btusb bind.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-29 16:31:15 -03:00
Peter Hurley 9fd481e03c Bluetooth: Allow ACL packets over USB in HCI_RAW mode
Removed tests which prevent transmission of ACL packets
when the device is in HCI_RAW mode. These tests verified that
there are ACL or LE links currently tracked by the HCI
connection manager. However, a HCI_RAW mode device does not
use the connection manager. In these circumstances, the connection
counts will be zero, and thus, transmitted ACL packets dropped.

The acl_num test is actually a vestige of a previous bulk URB
scheme that is no longer used by this driver (bulk URBs were not
started until at least one ACL connection was created). This was
incompatible with some endpoint implementations and was dropped -
see commit 43c2e57f94.

The utility of these tests is marginal - currently, the hci tx
scheduler cannot send an ACL or LE packet for an untracked connection
(except if the device is in HCI_RAW mode).

Lastly, no other transport layer driver enforces these same tests.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-27 18:15:45 -03:00
Jurgen Kramer f78b68261e Bluetooth: add support for 2011 mac mini
Today I noticed that the usb bluetooth adapter (BCM2046B1) on my 2011
mac mini was not working. I've created a patch to get it going.

Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-17 17:16:03 -03:00
Pieter-Augustijn Van Malleghem a63b723d02 Bluetooth: Add MacBookAir4,1 support
This patch against current git adds the hardware ID for the Apple
MacBookAir4,1, released in July 2011. The device features a BCM2046
USB chip. The patch was inspired by the previous modifications adding
support for the MacBookAir3,x.

Signed-off-by: Pieter-Augustijn Van Malleghem <p-a@scarlet.be>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-09-17 17:15:32 -03:00
Alan Stern 5b1b0b812a PM / Runtime: Add macro to test for runtime PM events
This patch (as1482) adds a macro for testing whether or not a
pm_message value represents an autosuspend or autoresume (i.e., a
runtime PM) event.  Encapsulating this notion seems preferable to
open-coding the test all over the place.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2011-08-19 23:49:48 +02:00
Ricardo Mendoza 8e7c3d2e4b Bluetooth: Add Toshiba laptops AR30XX device ID
Blacklist Toshiba-branded AR3011 based AR5B195 [0930:0215] and add to
ath3k.c for firmware loading.

Signed-off-by: Ricardo Mendoza <ricmm@gentoo.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-08-11 19:50:26 -03:00
Paul Bolle 4935f1c164 Bluetooth: btusb: be quiet on device disconnect
Disabling the bluetooth usb device embedded in (some) ThinkPads tends to
lead to errors like these:
    btusb_bulk_complete: hci0 urb ffff88011b9bfd68 failed to resubmit (19)
    btusb_intr_complete: hci0 urb ffff88011b46a318 failed to resubmit (19)
    btusb_bulk_complete: hci0 urb ffff88011b46a000 failed to resubmit (19)

That is because usb_disconnect() doesn't "quiesces" pending urbs.

Disconnecting a device is a normal thing to happen so it's no big deal
that usb_submit_urb() returns -ENODEV. The simplest way to get rid of
these errors is to stop treating that return as an error. Trivial,
actually.

While we're at it, add comments to be explicit about the reasons we're
not complaining about -EPERM and -ENODEV.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-08-11 19:50:25 -03:00
Steven.Li 2d25f8b462 Bluetooth: Add Atheros AR3012 one PID/VID supported
The new Ath3k needs to download patch and radio table,
and it keeps same PID/VID even after downloading the patch and radio
table. This patch is to use the bcdDevice (Device Release Number) to
judge whether the chip has been patched or not. The init bcdDevice
value of the chip is 0x0001, this value increases after patch and
radio table downloading.

Signed-off-by: Steven.Li <yongli@qca.qualcomm.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-07-01 14:48:02 -03:00
Andy Ross 2a7bccccdb Bluetooth: Device ids for ath3k on Pegatron Lucid tablets
New ath3k device IDs used on the Pegatron Lucid (ExoPC and WeTab) units.

Signed-off-by: Andy Ross <andy.ross@windriver.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-05-11 14:50:40 -03:00
Vinicius Costa Gomes 8693ac900e Bluetooth: Fix sending LE data over USB
Now that we have support for LE connections, before discarding a
frame we must check if there's a LE connection over that transport.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-03-31 14:25:25 -03:00
Marc-Antoine Perennou 88d377b6c3 Bluetooth: add support for Apple MacBook Pro 8,2
Just adding the vendor details makes it work fine.

Signed-off-by: Marc-Antoine Perennou <Marc-Antoine@Perennou.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-03-31 14:25:25 -03:00
Linus Torvalds e16b396ce3 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (47 commits)
  doc: CONFIG_UNEVICTABLE_LRU doesn't exist anymore
  Update cpuset info & webiste for cgroups
  dcdbas: force SMI to happen when expected
  arch/arm/Kconfig: remove one to many l's in the word.
  asm-generic/user.h: Fix spelling in comment
  drm: fix printk typo 'sracth'
  Remove one to many n's in a word
  Documentation/filesystems/romfs.txt: fixing link to genromfs
  drivers:scsi Change printk typo initate -> initiate
  serial, pch uart: Remove duplicate inclusion of linux/pci.h header
  fs/eventpoll.c: fix spelling
  mm: Fix out-of-date comments which refers non-existent functions
  drm: Fix printk typo 'failled'
  coh901318.c: Change initate to initiate.
  mbox-db5500.c Change initate to initiate.
  edac: correct i82975x error-info reported
  edac: correct i82975x mci initialisation
  edac: correct commented info
  fs: update comments to point correct document
  target: remove duplicate include of target/target_core_device.h from drivers/target/target_core_hba.c
  ...

Trivial conflict in fs/eventpoll.c (spelling vs addition)
2011-03-18 10:37:40 -07:00
David S. Miller 0a0e9ae1bd Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/bnx2x/bnx2x.h
2011-03-03 21:27:42 -08:00
Linus Torvalds 78794b2cde Revert "Bluetooth: Enable USB autosuspend by default on btusb"
This reverts commit 556ea928f7.

Jeff Chua reports that it can cause some bluetooth devices (he mentions
an Bluetooth Intermec scanner) to just stop responding after a while
with messages like

  [ 4533.361959] btusb 8-1:1.0: no reset_resume for driver btusb?
  [ 4533.361964] btusb 8-1:1.1: no reset_resume for driver btusb?

from the kernel. See also

  https://bugzilla.kernel.org/show_bug.cgi?id=26182

for other reports.

Reported-by: Jeff Chua <jeff.chua.linux@gmail.com>
Reported-by: Andrew Meakovski <meako@bigmir.net>
Reported-by: Jim Faulkner <jfaulkne@ccs.neu.edu>
Acked-by: Greg KH <gregkh@suse.de>
Acked-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Cc: stable@kernel.org (for 2.6.37)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-02-23 19:42:03 -08:00
John W. Linville b67afe7f43 Merge ssh://master.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
Conflicts:
	drivers/bluetooth/ath3k.c
	drivers/bluetooth/btusb.c
2011-02-18 17:03:41 -05:00
Gustavo F. Padovan 03c2d0e894 Bluetooth: Use usb_fill_int_urb()
Instead set urb structure directly we call usb_fill_int_urb() to set the
values to us.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-16 16:33:22 -03:00
Cho, Yu-Chen e9036e336a Bluetooth: Add Atheros BT AR5BBU12 fw supported
Add the btusb.c blacklist [0489:e02c] for Atheros AR5BBU12 BT
and add to ath3k.c supported this device.

Signed-off-by: Cho, Yu-Chen <acho@novell.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-16 15:54:11 -03:00
Oliver Neukum 8efdd0cdc5 Bluetooth: fix crash with quirky dongles doing sound
Quirky dongles sometimes do not use the iso interface which
causes a crash with runtime PM

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-16 15:53:45 -03:00
Bala Shanmugam d9f51b51db Bluetooth: Add firmware support for Atheros 3012
Blacklisted AR3012 PID in btusb and added the same
in ath3k to load patch and sysconfig files.

Signed-off-by: Bala Shanmugam <sbalashanmugam@atheros.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-02-11 15:21:46 -02:00
Cho, Yu-Chen 509e7861d8 Bluetooth: add Atheros BT AR9285 fw supported
Add the btusb.c blacklist [03f0:311d] for Atheros AR9285 Malbec BT
and add to ath3k.c ath3-1.fw (md5:1211fa34c09e10ba48381586b7c3883d)
supported this device.

Signed-off-by: Cho, Yu-Chen <acho@novell.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-01-26 15:23:05 -02:00
Jesper Juhl 42b16b3fbb Kill off warning: ‘inline’ is not at beginning of declaration
Fix a bunch of
	warning: ‘inline’ is not at beginning of declaration
messages when building a 'make allyesconfig' kernel with -Wextra.

These warnings are trivial to kill, yet rather annoying when building with
-Wextra.
The more we can cut down on pointless crap like this the better (IMHO).

A previous patch to do this for a 'allnoconfig' build has already been
merged. This just takes the cleanup a little further.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-01-19 15:43:08 +01:00
Bala Shanmugam be93112acc Bluetooth: Add new PID for Atheros 3011
Atheros 3011 has small sflash firmware and needs to be
blacklisted in transport driver to load actual firmware
in DFU driver.

Signed-off-by: Bala Shanmugam <sbalashanmugam@atheros.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-12-01 15:51:01 -02:00
Stefan Seyfried 61faddf661 Bluetooth: Fix log spamming in btusb due to autosuspend
If a device is autosuspended an inability to resubmit URBs is
to be expected. Check the error code and only log real errors.
(Now that autosuspend is default enabled for btusb, those log
messages were happening all the time e.g. with a BT mouse)

Signed-off-by: Stefan Seyfried <seife+kernel@b1-systems.com>
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-12-01 15:46:42 -02:00
Edgar (gimli) Hucek 3e3ede7dda Bluetooth: Add MacBookAir3,1(2) support
Adding the new MacBookAir3,1(2) to btusb.

Output without the patch and btusb loaded :

T:  Bus=03 Lev=02 Prnt=03 Port=02 Cnt=01 Dev#=  6 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=05ac ProdID=821b Rev= 0.34
S:  Manufacturer=Apple Inc.
S:  Product=Bluetooth USB Host Controller
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  32 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  32 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Output with the patch and btusb loaded :

T:  Bus=03 Lev=02 Prnt=03 Port=02 Cnt=01 Dev#=  6 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=05ac ProdID=821b Rev= 0.34
S:  Manufacturer=Apple Inc.
S:  Product=Bluetooth USB Host Controller
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  32 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  32 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Signed-off-by: Edgar (gimli) Hucek <gimli@dark-green.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-11-09 01:08:53 -02:00
Matthew Garrett 556ea928f7 Bluetooth: Enable USB autosuspend by default on btusb
We've done this for a while in Fedora without any obvious problems other
than some interaction with input devices. Those should be fixed now, so
let's try this in mainline.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-11-09 00:55:27 -02:00
Nobuhiro Iwamatsu 3cd01976e7 Bluetooth: Add support Bluetooth controller of MacbookPro 7,1
Bluetooth controller of MacbookPro 7,1 does not work.
Because Device Class of these controllers was set 255 (Vendor Sepecific Class).

T:  Bus=04 Lev=02 Prnt=04 Port=00 Cnt=01 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=05ac ProdID=8213 Rev=01.86
S:  Manufacturer=Apple Inc.
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=5C5948C81B99
C:  #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none)

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-10-12 12:44:52 -03:00
Nobuhiro Iwamatsu 9c047157a2 Bluetooth: Add support Bluetooth controller of MacbookPro 6,2
Bluetooth controller of MacbookPro 6,2 does not work.
Because Device Class of these controllers was set 255 (Vendor Sepecific Class).

T:  Bus=01 Lev=03 Prnt=03 Port=02 Cnt=03 Dev#=  8 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=05ac ProdID=8218 Rev=00.22
S:  Manufacturer=Apple Inc.
S:  Product=Bluetooth USB Host Controller
C:  #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2010-10-12 12:44:52 -03:00
Gustavo F. Padovan 08b8b6c454 Bluetooth: Move bit-field variable in USB driver to data->flags
did_iso_resume keeps only a bit-field value, so moving that to a proper
flags place.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-07-21 10:39:12 -07:00
Cyril Lacoux 0a79f67445 Bluetooth: Added support for controller shipped with iMac i5
Device class is ff(vend.) instead of e0(wlcon).

Output from command `usb-devices`:
T:  Bus=01 Lev=03 Prnt=03 Port=00 Cnt=01 Dev#=  6 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=05ac ProdID=8215 Rev=01.82
S:  Manufacturer=Apple Inc.
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=7C6D62936607
C:  #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none)

Signed-off-by: Cyril Lacoux <clacoux@ifeelgood.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-07-21 10:39:12 -07:00
Marcel Holtmann c13854cef4 Bluetooth: Convert controller hdev->type to hdev->bus
The hdev->type is misnamed and should be actually hdev->bus instead. So
convert it now.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2010-02-27 14:05:38 +01:00
Oliver Neukum 652fd781a5 Bluetooth: Prevent ill-timed autosuspend in USB driver
The device must be marked busy as it receives data.

Signed-off-by: Oliver Neukum <oliver@neukum.org>
Tested-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-12-17 12:12:49 -08:00
Alan Stern fb34d53752 USB: remove the auto_pm flag
This patch (as1302) removes the auto_pm flag from struct usb_device.
The flag's only purpose was to distinguish between autosuspends and
external suspends, but that information is now available in the
pm_message_t argument passed to suspend methods.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11 11:55:21 -08:00
Oliver Neukum 7b8e2c1db0 fix memory leak in fixed btusb_close
If the waker is killed before it can replay outstanding URBs, these URBs
won't be freed or will be replayed at the next open.  This patch closes
the window by explicitely discarding outstanding URBs.

Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-11-14 12:57:08 -08:00
Linus Torvalds 404291ac9e btusb bluetooth driver: wait for 'waker' work too before closing
Rafael debugged a resume-time hang (with oopses in workqueue handling)
on his laptop that was due to the 'waker' workqueue entry being
disconnected and then released without the workqueue entry having been
synchronized.

Several people were involved, with Oleg Nesterov doing a debugging patch
showing what workqueue entry was corrupt etc.

This was a regression introduced by commit 7bee549e19 ("Bluetooth: Add
USB autosuspend support to btusb driver") as Rafael points out (not
actually bisected, but it became clear once the bug was found).

Tested-and-reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Oliver Neukum <oliver@neukum.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-11-11 13:32:29 -08:00
Oliver Neukum 7bee549e19 Bluetooth: Add USB autosuspend support to btusb driver
This patch adds support of USB autosuspend to the btusb driver.

If the device doesn't support remote wakeup, simple support based on
up/down is provided. If the device supports remote wakeup, additional
support for autosuspend while the interface is up is provided. This is
done by queueing URBs in an anchor structure and waking the device up
from a work queue on sending. Reception triggers remote wakeup.

The last busy facility of the USB autosuspend code is used. To close
a race between autosuspend and transmission, a counter of ongoing
transmissions is maintained.

Add #ifdefs for CONFIG_PM as necessary.

Signed-off-by: Oliver Neukum <oliver@neukum.org>
Tested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-24 16:31:24 -07:00
Vikram Kandukuri 290ba20081 Bluetooth: Improve USB driver throughput by increasing the frame size
This patch increases the receive buffer size to HCI_MAX_FRAME_SIZE
which improves the RX throughput considerably.

Tested against BRM/Atheros/CSR USB Dongles with PAN profile using
iperf and chariot. This gave significant (around 40%) increase
in performance (increased from 0.8 to 1.5 Mb/s in Sheld room)

Signed-off-by: Vikram Kandukuri <vikram.kandukuri@atheros.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22 14:12:37 -07:00
Marcel Holtmann 43c2e57f94 Bluetooth: Submit bulk URBs along with interrupt URBs
Submitting the bulk URBs for ACL data transfers only on demand has no
real benefit compared to just submit them when a Bluetooth device gets
opened. So when submitting the interrupt URBs for HCI events, just
submit the bulk URBs, too.

This solves a problem with some Bluetooth USB dongles that has been
reported over the last few month. These devices require that the bulk
URBs are actually present. These devices are really broken, but there
is nothing we can do about it.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-02-27 06:14:36 +01:00
Marcel Holtmann a418b893a6 Bluetooth: Enable per-module dynamic debug messages
With the introduction of CONFIG_DYNAMIC_PRINTK_DEBUG it is possible to
allow debugging without having to recompile the kernel. This patch turns
all BT_DBG() calls into pr_debug() to support dynamic debug messages.

As a side effect all CONFIG_BT_*_DEBUG statements are now removed and
some broken debug entries have been fixed.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-11-30 12:17:28 +01:00
Marcel Holtmann 5ddd4a6068 Bluetooth: Allow SCO audio with Asus WL-BTD202 dongle
This patch allows the Asus WL-BTD202 dongle to be used with a mono
headset without having to specify "options btusb force_scofix=1".

Based on a patch from Guillaume Bedot <littletux@zarb.org>

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-11-30 12:17:27 +01:00
Marcel Holtmann 7a9d402053 Bluetooth: Send HCI Reset command by default on device initialization
The Bluetooth subsystem was not using the HCI Reset command when doing
device initialization. The Bluetooth 1.0b specification was ambiguous
on how the device firmware was suppose to handle it. Almost every device
was triggering a transport reset at the same time. In case of USB this
ended up in disconnects from the bus.

All modern Bluetooth dongles handle this perfectly fine and a lot of
them actually require that HCI Reset is sent. If not then they are
either stuck in their HID Proxy mode or their internal structures for
inquiry and paging are not correctly setup.

To handle old and new devices smoothly the Bluetooth subsystem contains
a quirk to force the HCI Reset on initialization. However maintaining
such a quirk becomes more and more complicated. This patch turns the
logic around and lets the old devices disable the HCI Reset command.

The only device where the HCI_QUIRK_NO_RESET is still needed are the
original Digianswer devices and dongles with an early CSR firmware.

CSR reported that they fixed this for version 12 firmware. The last
official release of version 11 firmware is build ID 115. The first
version 12 candidate was build ID 117.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-11-30 12:17:26 +01:00
Marcel Holtmann 6a88adf2ad Bluetooth: Add suspend/resume support to btusb driver
During suspend it is important that all URBs are cancelled and then on
resume re-submitted. This gives initial suspend/resume support.

Based on initial work from Oliver Neukum <oneukum@suse.de>

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-11-30 12:17:14 +01:00
Marcel Holtmann a780efa812 Bluetooth: Handle bulk URBs in btusb driver from notify callback
With the addition of usb_unlink_anchored_urbs() it is possible to fully
control the bulk URBs from the notify callback. There is no need to
schedule work and so only do this for the ISOC URBs.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-11-30 12:17:12 +01:00
Marcel Holtmann 2eda66f4a0 Bluetooth: Add fine grained mem_flags usage to btusb driver
The URB submission routines need more fine grained control for the
mem_flags used by kmalloc(), usb_alloc_urb() and usb_submit_urb() to
better support different caller situations. Add a mem_flags parameter
and give the caller full control.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-11-30 12:17:10 +01:00
Marcel Holtmann 1305e9e799 [Bluetooth] Add reset quirk for A-Link BlueUSB21 dongle
The new A-Link Bluetooth dongle is another one based on the BCM2046 chip
from Broadcom and it also needs to send HCI_Reset before it becomes fully
operational. Without the quirk it will show a lot of I/O errors.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-10-06 12:22:52 +02:00
Marcel Holtmann 4f62f6cb93 [Bluetooth] Add reset quirk for new Targus and Belkin dongles
Targus and Belkin have come out with new Bluetooth 2.1 capable dongles
using the latest BCM2046 chip from Broadcom. Both of them are so called
HID proxy dongles and they need to send HCI_Reset before they become
fully operational.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-10-06 12:22:51 +02:00
Marcel Holtmann 36010ff678 [Bluetooth] Fix double frees on error paths of btusb and bpa10x drivers
The transfer buffer of an URB will be automatically freed when using
the URB_FREE_BUFFER transfer_flag. So the extra calls to kfree() will
cause a double free.

Reported-by: Justin Mattock <justinmattock@gmail.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-10-06 12:22:51 +02:00
Marcel Holtmann 5fbcd260c2 [Bluetooth] Fix USB disconnect handling of btusb driver
The USB transport specification for Bluetooth splits the ACL and SCO
handling into two separate interfaces. In Linux it possible to probe
and disconnect these interfaces independently. So make sure that both
interfaces are tightly bound together.

This fixes the suspend regression that some people have expierenced.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2008-09-23 00:16:36 +02:00