Rename sound card driver source file to encompass not only OMAP4 but future
OMAP versions that feature HDMI.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Rename all the relevant structures, variables and functions to not
make specific reference to OMAP4. This is to make the driver encompass
future OMAP versions that feature HDMI and not only OMAP4. These
changes are only in naming. There are not functional changes.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Make Kconfig and Makefile more generic to encompass not only
OMAP4 but other OMAP processors featuring HDMI.
Also, relax the dependency list to depend only on any OMAP processor
supporting OMAP2_DSS and OMAP4_DSS_HDMI. As HDMI support for
future OMAP versions is added, the dependency list must change
accordingly.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
According to the HDMI specification, a source is permitted to
transmit L-PCM audio in the following sample rates: 32kHz, 44.1kHz,
48kHz, 88.2kHz, 96kHz, 176.4kHz or 192kHz.
It also supports up to 8 audio channels.
The sink may not necessarily support all these sample rates and
channels. However, as this CPU DAI describes the HDMI source, it
makes sense to include them. The limitation of capabilities as
supported by the sink should be done in the ASoC HDMI codec.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Before starting to play audio, we need to make sure that the
display is active and the current video mode supports audio. instead
of using the overlay manager in the machine driver, we use the DSS audio
interface's audio_supported function. As we already have a pointer to
the correct dssdev, we do not have to look for it every time audio is
to be played. Also, the CPU DAI startup function is called earlier
than the card hw_param function. Hence and we can detect the state of
the display earlier.
While there, add a error message if the constraint cannot be applied.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
squash to improve err
Signed-off-by: Liam Girdwood <lrg@ti.com>
Expand the configuration of the hw_params to include the IEC-60958
channel status word and the CEA-861 audio infoframe. The configuration
of such structures depends on the snd_pcm_hw_params received. A
omap_dss_audio is used to pass the configuration parameters to DSS.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Instead of accessing the HDMI IP directly, the CPU DAI driver takes
advantage of the audio interface provided by the DSS device driver.
The ASoC driver will link the DSS audio functionality with ALSA by
calling the appropriate DSS device driver functions at the relevant
moments. For this, three new DAI operations are added: trigger, prepare
and shutdown operations.
At the moment, it is assumed that only one HDMI display is available
in the system, as it is the case in OMAP4. However, in the future,
one DAI for each HDMI display should be provided.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Create a struct hdmi_priv to store the relevant data of the CPU DAI
driver. As more data is added to the driver, having all the data
in the same location eases its handling. At the moment, only the DMA
configuration parameters are included in the structure.
Also, the required memory is allocated using devm_kzalloc rather than
using a static global variable.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
When getting the needed resources fails, return -ENODEV. This is more
in line with other drivers do and it gives a more descriptive error.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In order to utilize the new OMAP HDMI codec and the updated name of
the device of the CPU DAI, update the names at the drivers accordingly.
While there, also update the name of the machine driver to be more
generic and encompass more OMAP processors featuring HDMI and not
only OMAP4.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In preparation to Device Tree support.
With DT booted kernel we can not rely on pdata which used to
hold information needed for the driver at runtime.
Use the card's driver data to hold these informations from now on.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The needed change in routing will be done runtime for the non
twl6040 connected widgets, like the Digital microphone.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
There is no need to have two snd_soc_dai_link structure for the two setup
the machine driver supports.
We can just tell core to register only the first link if the DMIC link is
not in use on the device.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Device tree support for OMAP4+ dmic cpu dai driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Device tree support for OMAP4+ McPDM cpu dai driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In capture stream the buffer size does not need to be constrained to be
bigger then the McBSP FIFO.
In capture the FIFO content is taken out in period length burst, this
enusres that the FIFO is not going to overflow.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
With the common irq the driver only needs to use one interrupt line, and
it provides better debugging possibilites compared to the legacy TX/RX
interrupt lines.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The frame dma_op_mode has never been used, and it is just creating
confusion for users/developers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Take the DMA packet mode into use when the McBSP is configured in element
dma_op_mode if the stream is not mono.
In this way we transfer one sample from/to McBSP FIFO upon DMA request.
This change only affects OMAP3+ versions, where the McBSP ports have FIFO.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Introduce codec for HDMI. At the moment, this is a dummy codec. In the
future it will parse the EDID to modify the supported parameters, such
as the number of channels and the sample rates. At the moment, it blindly
supports all the sample rates and audio channels described in the HDMI
1.4a specification.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As good as nothing exciting here; just a few trivial fixes for
various ASoC stuff.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=ZPkR
-----END PGP SIGNATURE-----
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound sound fixes from Takashi Iwai:
"As good as nothing exciting here; just a few trivial fixes for various
ASoC stuff."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: omap-pcm: Free dma buffers in case of error.
ASoC: s3c2412-i2s: Fix dai registration
ASoC: wm8350: Don't use locally allocated codec struct
ASoC: tlv312aic23: unbreak resume
ASoC: bf5xx-ssm2602: Set DAI format
ASoC: core: check of_property_count_strings failure
ASoC: dt: sgtl5000.txt: Add description for 'reg' field
ASoC: wm_hubs: Make sure we don't disable differential line outputs
Signed-off-by: Oleg Matcovschi <oleg.matcovschi@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Complete the separation of the twl6040 from the twl core since
it is a separate chip, not part of the twl6030 PMIC.
Make the needed Kconfig changes for the depending drivers at the
same time to avoid breaking the kernel build (vibra, ASoC components).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
These changes are all specific to one board only. We're trying to keep
the number of board files low, but generally board level updates are
ok on platforms that are working on moving towards DT based probing,
which will eventually lead to removing them.
The board-ams-delta.c board file gets a conflict between the removal of
ams_delta_config and the addition of a lot of other data. The Kconfig
file has two changes in the same line, and in exynos, the power domain
cleanup conflicts with the addition of the image sensor device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: Amended a fix for a mismerge to board-omap4panda.c]
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPckIXAAoJEIwa5zzehBx35uUP/jns0renNAMmiu2vBHGQtn4z
xiNXjDTJ8DeD4mKf17rjn/uaJgQ0w3Doq2nEsi5rPqLK4Uqqk+NG1zYa77QBWHbx
FUgBPz+oViTDkanp4G8cygXvGfNkb1GvuJxEBvxQ1mwuG4JhwlFbQxGIaS8ZwOAN
DIyVCgSXy40B+748RwdZ2AY7CYvWiQWrQYsIH6NO0rtZIXjyV0kIsyVtEXZpqWtF
xNz2HHXVMrui2JQ7FQ0zZglY8+YCxjeJk4v++FfqCJiMzU1yZJw7E30NjhcWAaR6
odJM2YIyhvunxPfx3ZUHimsNjfU+l/0uXgDHeLFSWVyIjPFXwqZDi/6onP3FI4Jc
sIoTSwDAQpnZJ6KffAYkcyyfsWN61GOE96Xa2eRb6+78CEiMh7vJ8TIRieiOWxjm
NbB0xzaKxa97F/8z7w6V6Z4dNhnokWJZvtJdgLZUYAqIgnxstFkJZ9+Tqt77G4t3
5iSbIMeFPsfh5sUeAVjr5+zVeUOm9PTRI0n0RY+Wd16Ke6DO1qobKAYOzrzI5idz
k7ni76/zgGn3NS5F3TxdRHowkeGUwUU6poyopgQ0pyscDylVpzgMIqmAwLdzrVp5
joVEoKi6h4oqhAZtiysXuF85bUfCW0ziDUuib07SX8wcEIAIr+mWob1Ei+wJrefe
g0Ch3ZbCRQMOwSOQ70Ci
=HPiJ
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: board specific updates" from Arnd Bergmann/Olof Johansson:
"These changes are all specific to one board only. We're trying to
keep the number of board files low, but generally board level updates
are ok on platforms that are working on moving towards DT based
probing, which will eventually lead to removing them.
The board-ams-delta.c board file gets a conflict between the removal
of ams_delta_config and the addition of a lot of other data. The
Kconfig file has two changes in the same line, and in exynos, the
power domain cleanup conflicts with the addition of the image sensor
device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: Amended a fix for a mismerge to board-omap4panda.c]
Signed-off-by: Olof Johansson <olof@lixom.net>"
Fixed up some fairly trivial conflicts manually.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (82 commits)
i.MX35-PDK: Add Camera support
ARM : mx35: 3ds-board: add framebuffer device
pxa/hx4700: Remove pcmcia platform_device structure
ARM: pxa/hx4700: Reduce sleep mode battery discharge by 35%
ARM: pxa/hx4700: Remove unwanted request for GPIO105
ARM: EXYNOS: support Exynos4210-bus Devfreq driver on Nuri board
ARM: EXYNOS: Register JPEG on nuri
ARM: EXYNOS: Register JPEG on universal_c210
ARM: S5PV210: Enable JPEG on SMDKV210
ARM: S5PV210: Add JPEG board definition
ARM: EXYNOS: Enable JPEG on Origen
ARM: EXYNOS: Enable JPEG on SMDKV310
ARM: EXYNOS: Add __init attribute to universal_camera_init()
ARM: EXYNOS: Add __init attribute to nuri_camera_init()
ARM: S5PV210: Enable FIMC on SMDKC110
ARM: S5PV210: Enable FIMC on SMDKV210
ARM: S5PV210: Enable MFC on SMDKC110
ARM: S5PV210: Enable MFC on SMDKV210
ARM: EXYNOS: Enable G2D on SMDKV310
ARM: tegra: update defconfig
...
The asoc branch that was already merged into v3.4 contains some
board-level changes that conflict with patches we already have
here, so pull in that branch to resolve the conflicts.
Conflicts:
arch/arm/mach-imx/mach-imx27_visstrim_m10.c
arch/arm/mach-omap2/board-omap4panda.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: Amended fix for mismerge as reported by Kevin Hilman]
Signed-off-by: Olof Johansson <olof@lixom.net>
The McBSP driver stack has been moved, and rewritten resulting a single
driver - selected by CONFIG_SND_OMAP_SOC_MCBSP. There is no longer need to
have CONFIG_OMAP_MCBSP anymore.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonoie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
We are setting SNDRV_PCM_HW_PARAM_BUFFER_SIZE based on
SNDRV_PCM_HW_PARAM_CHANNELS, not vice versa. This bug didn't
have much impact because the rules are evaluated multiple times
by the core, and intended value got set eventually.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Remove the no longer valid check for McBSP1 regarding to signal mux
selection (on OMAP4 McBSP4 has 6 pin setup).
Only clear the srgr2, pcr0 register configuration if the requested clock
configuration will actually going to touch it. In this way we can avoid
issues if the CLKR/FSR mux has been configured after the clock selection.
We are going to check for the valid McBSP port in the
omap_mcbsp_6pin_src_mux() function based on the validity of the mux_signal
callback (which is only valid for ports having 6 pin setup).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Use single function for the CLKR/FSR mux configuration.
OMAP2/3 has 6 pin configuration on McBSP1 instance, while on OMAP4
McBSP4 instance have the 6 pin configuration so the omap2_mcbsp1_mux_* is
not correct name for all support OMAP versions
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Clock signal muxing, and functional clock related defines are only needed
in ASoC drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Mark Brown <broonoie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
On OMAP4 we have one interrupt line per McBSP port.
At probe time tx, and rx irq value will be -ENXIO,
and only the tx irq will get corrected.
In omap_mcbsp_request if the rx_irq is not 0 we proceed,
and try to request the interrupt, which will fail on
OMAP4 (rx_irq == -6).
To avoid this error, clear the rx_irq at probe time
on OMAP4.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
If external source for the CLKS signal selection kept after the port is no
longer in use the system might refuse to go suspend.
There is also a chance that the external clock is not running when next
time the McBSP port is started which can result errors when we try to
access McBSP registers.
Reset the CLKS source back to PRCM source unconditionally.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Configure the WAKEUPEN register at the same time we configure the rest of
the McBSP registers.
In case of OMAP3+, if the sysclock has been reconfigured we are going to
disable McBSP for the duration of the clock change, which will reset the
McBSP registers. The WAKEUPEN register need to be configured later, so
the changes will be effective during runtime.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicrocom>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The parent functions of omap_st_start/stop also checks the validity of the
st_data pointer so we do not need to do it again inside of omap_st_start/stop
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In this way we can save few lines, and have uniform way of initializing the
st_data in all functions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Configure the DMA request line, port address, and stream name at
probe time instead of every time we start a stream.
These settings are static in the system.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Since the drivers has been merged, merge the two structures together.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Use devm_* where it is possible to save on cleanup path.
Start merging the two mcbsp file content.
Move pm_runtime_enable/disable calls to ASoC probe, remove from module
probe/remove time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
We no longer need accessor functions for max_tx/rx_threshold, dma_op_mode
or for the FIFO size.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Use BIT() for bit position, correct field definition by adding mask to
them, and also adding the missing spaces around '<<'
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The OMAP McBSP driver stack used to contain two different
drivers. One of them was used as kind low-level access to
the IP, while the other driver was the ASoC DAI driver.
There were global, shared structures, in different places,
the McBSP instances are reffered with id numbers (sometimes
0 based, in other cases 1 based id numbers).
Create one single driver for OMAP McBSP with name: omap-mcbsp.
Convert the old omap-mcbsp driver initially to be a library
for the omap-mcbsp DAI driver. With this change we can get rid
of all global variables, structures.
Further cleanup is coming...
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Move most of the content of the plat/mcbsp.h header file under
sound/soc/omap/ to help further cleanups.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In order to consolidate the McBSP driver move it out from
arch/arm/plat-omap directory under sound/soc/omap/
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
This functionality has already been implemented in the cx20442 codec
driver (commit f75a8ff67d, "ASoC: cx20442:
add bias control over a platform provided regulator"), no need to keep
it here duplicated.
Once done, remove the no longer used AMS_DELTA_LATCH2_MODEM_NRESET
symbol from the board header file and a call to the regulator_toggle()
helper function from the old API wrapper found in the board file. While
being at it, simplify the way the modem .pm callback handles the
regulator and drop that helper function and its related consumer setup
completely.
Depends on patches 1/3 and 2/3 for clean apply and keep things working.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
of bugfixes and driver updates there's quite a few framework enhancements.
Most are either small or are laying the groundwork for user visible
features (especially dynamic PCM), the most directly visible change is
the dmaengine library. There's also a bunch of regmap API enhancements
pulled into the tree so that either the framework or drivers can take
advantage of the new features.
Changes include:
- Support for widgets not associated with a CODEC, an important part of
the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based DMA
drivers contributed by Lars-Peter Clausen. This will save a lot of
code and make it much easier to deploy enhancements to dmaengine.
- Support for binary controls, used for providing runtime configuration
of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do without
any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much effort to
put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics WM2200.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=FpJH
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into topic/asoc
This has been a very active release for ASoC, as well as the usual raft
of bugfixes and driver updates there's quite a few framework enhancements.
Most are either small or are laying the groundwork for user visible
features (especially dynamic PCM), the most directly visible change is
the dmaengine library. There's also a bunch of regmap API enhancements
pulled into the tree so that either the framework or drivers can take
advantage of the new features.
Changes include:
- Support for widgets not associated with a CODEC, an important part of
the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based DMA
drivers contributed by Lars-Peter Clausen. This will save a lot of
code and make it much easier to deploy enhancements to dmaengine.
- Support for binary controls, used for providing runtime configuration
of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do without
any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much effort to
put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics WM2200.
Fix below build error which is introduced by
commit 022658 "ASoC: core: Add support for DAI and machine kcontrols".
CC [M] sound/soc/omap/n810.o
sound/soc/omap/n810.c: In function 'n810_set_input':
sound/soc/omap/n810.c:194: error: 'codec' undeclared (first use in this function)
sound/soc/omap/n810.c:194: error: (Each undeclared identifier is reported only once
sound/soc/omap/n810.c:194: error: for each function it appears in.)
sound/soc/omap/n810.c:188: warning: unused variable 'card'
make[3]: *** [sound/soc/omap/n810.o] Error 1
make[2]: *** [sound/soc/omap] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently ASoC can only add kcontrols using codec and platform component device
handles. It's also desirable to add kcontrols for DAIs (i.e. McBSP) and for
SoC card machine drivers too. This allows the kcontrol to have a direct handle to
the parent ASoC component DAI/SoC Card/Platform/Codec device and hence easily
get it's private data.
This change makes snd_soc_add_controls() static and wraps it in the folowing
calls (card and dai are new) :-
snd_soc_add_card_controls()
snd_soc_add_codec_controls()
snd_soc_add_dai_controls()
snd_soc_add_platform_controls()
This patch also does a lot of small mechanical changes in individual codec drivers
to replace snd_soc_add_controls() with snd_soc_add_codec_controls().
It also updates the McBSP DAI driver to use snd_soc_add_dai_controls().
Finally, it updates the existing machine drivers that register controls to either :-
1) Use snd_soc_add_card_controls() where no direct codec control is required.
2) Use snd_soc_add_codec_controls() where there is direct codec control.
In the case of 1) above we also update the machine drivers to get the correct
component data pointers from the kcontrol (rather than getting the machine pointer
via the codec pointer).
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Enable ASoC audio support for OMAP4 based machines with
twl6040 codec via the omap-abe-twl6040 machine driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Avoid using hardwired configuration for MCLK frequency.
Different board design might use other MCLK frequency.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Disable the not connected pins on the board based on the
received platform data.
DO not register the jack function on boards, which does not have
means to detect it (jack is always connected).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ricardo Neri
Peter Ujfalusi
Linus Torvalds
Oleg Matcovschi
Arnd Bergmann
Grazvydas Ignotas
Janusz Krzysztofik
Takashi Iwai
Axel Lin
Liam Girdwood