If, while locating GPIOs by name, we get probe deferral, we should
immediately report it to caller rather than trying to fall back to parsing
unnamed GPIOs from _CRS block.
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-and-Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On Bay Trail / Cherry Trail systems with a LID switch, the LID switch is
often connect to a gpioint handled by an _IAE event handler.
Before this commit such systems would not wake up when opening the lid,
requiring the powerbutton to be pressed after opening the lid to wakeup.
Note that Bay Trail / Cherry Trail systems use suspend-to-idle, so
the interrupts are generated anyway on those lines on lid switch changes,
but they are treated by the IRQ subsystem as spurious while suspended if
not marked as wakeup IRQs.
This commit calls enable_irq_wake() for _IAE GpioInts with a valid
event handler which have their Wake flag set. This fixes such systems
not waking up when opening the lid.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When an interrupt occurs on an MCP23S08 chip, the INTF register will only
contain one bit as causing the interrupt. If more than two pins change at
the same time on the chip, this causes one of the pins to not be reported.
This patch fixes the logic for checking if a pin has changed, so that
multiple pins will always cause more than one change.
Cc: stable@vger.kernel.org
Signed-off-by: Robert Middleton <robert.middleton@rm5248.com>
Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When a threaded irq handler is chained attached to one of the gpio
pins when configure for level irq the altera_gpio_irq_leveL_high_handler
does not mask the interrupt while being handled by the chained irq.
This resulting in the threaded irq not getting enough cycles to complete
quickly enough before the irq was disabled as faulty. handle_level_irq
should be used in this situation instead of handle_simple_irq.
In gpiochip_irqchip_add set default handler to handle_bad_irq as
per Documentation/gpio/driver.txt. Then set the correct handler in
the set_type callback.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When CONFIG_PM_SLEEP is disabled, we get a warning about unused functions:
drivers/gpio/gpio-xgene.c:155:12: warning: 'xgene_gpio_resume' defined but not used [-Wunused-function]
static int xgene_gpio_resume(struct device *dev)
^~~~~~~~~~~~~~~~~
drivers/gpio/gpio-xgene.c:142:12: warning: 'xgene_gpio_suspend' defined but not used [-Wunused-function]
static int xgene_gpio_suspend(struct device *dev)
The warnings are harmless and can be avoided by simplifying the code and marking
the functions as __maybe_unused.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
copy_from_user() returns the number of bytes remaining to be copied but
we want to return negative error codes on failue.
Fixes: 9202ba2397 ("gpio: mockup: implement event injecting over debugfs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set the gpio_chip parent property since some recent functions
such as devprop_gpiochip_set_names() can use it.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Augment fwnode_get_named_gpiod() to configure the GPIO pin
immediately after requesting it like all other APIs do.
This is a treewide change also updating all users.
- Pass a GPIO label down to gpiod_request() from
fwnode_get_named_gpiod(). This makes debugfs and the userspace
ABI correctly reflect the current in-kernel consumer of a pin
taken using this abstraction. This is a treewide change also
updating all users.
- Rename devm_get_gpiod_from_child() to
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object. This is a treewide
change also updating all users.
- Make it possible to take multiple GPIOs in a single hog of device
tree hogs.
- The refactorings switching GPIO chips to use the .set_config()
callback using standard pin control properties and providing
a backend into the pin control subsystem that were also merged
into the pin control tree naturally appear here too.
Testing instrumentation:
- A whole slew of cleanups and improvements to the mockup GPIO
driver. We now have an extended userspace test exercising the
subsystem, and we can inject interrupts etc from userspace
to fully test the core GPIO functionality.
New drivers:
- New driver for the Cortina Systems Gemini GPIO controller.
- New driver for the Exar XR17V352/354/358 chips.
- New driver for the ACCES PCI-IDIO-16 PCI GPIO card.
Driver changes:
- RCAR: set the irqchip parent device, add fine-grained runtime
PM support.
- pca953x: support optional RESET control line on the chip.
- DaVinci: cleanups and simplifications. Add support for multiple
instances.
- .set_multiple() and naming of lines on more or less all of the
ISA/PCI GPIO controllers.
- mcp23s08: refactored to use regmap as a first step to further
rewrites and modernizations.
-----BEGIN PGP SIGNATURE-----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=O81I
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.11 cycle
Core changes:
- Augment fwnode_get_named_gpiod() to configure the GPIO pin
immediately after requesting it like all other APIs do. This is a
treewide change also updating all users.
- Pass a GPIO label down to gpiod_request() from
fwnode_get_named_gpiod(). This makes debugfs and the userspace ABI
correctly reflect the current in-kernel consumer of a pin taken
using this abstraction. This is a treewide change also updating all
users.
- Rename devm_get_gpiod_from_child() to
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object. This is a treewide change
also updating all users.
- Make it possible to take multiple GPIOs in a single hog of device
tree hogs.
- The refactorings switching GPIO chips to use the .set_config()
callback using standard pin control properties and providing a
backend into the pin control subsystem that were also merged into
the pin control tree naturally appear here too.
Testing instrumentation:
- A whole slew of cleanups and improvements to the mockup GPIO
driver. We now have an extended userspace test exercising the
subsystem, and we can inject interrupts etc from userspace to fully
test the core GPIO functionality.
New drivers:
- New driver for the Cortina Systems Gemini GPIO controller.
- New driver for the Exar XR17V352/354/358 chips.
- New driver for the ACCES PCI-IDIO-16 PCI GPIO card.
Driver changes:
- RCAR: set the irqchip parent device, add fine-grained runtime PM
support.
- pca953x: support optional RESET control line on the chip.
- DaVinci: cleanups and simplifications. Add support for multiple
instances.
- .set_multiple() and naming of lines on more or less all of the
ISA/PCI GPIO controllers.
- mcp23s08: refactored to use regmap as a first step to further
rewrites and modernizations"
* tag 'gpio-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (61 commits)
gpio: reintroduce devm_get_gpiod_from_child()
gpio: pci-idio-16: Fix PCI BAR index
gpio: pci-idio-16: Fix PCI device ID code
gpio: mockup: implement event injecting over debugfs
gpio: mockup: add a dummy irqchip
gpio: mockup: implement naming the lines
gpio: mockup: code shrink
gpio: mockup: readability tweaks
gpio: Add GPIO support for the ACCES PCI-IDIO-16
gpio: Add the devm_fwnode_get_index_gpiod_from_child() helper
gpio: Rename devm_get_gpiod_from_child()
gpio: mcp23s08: Select REGMAP/REGMAP_I2C to fix build error
gpio: ws16c48: Add support for GPIO names
gpio: gpio-mm: Add support for GPIO names
gpio: 104-idio-16: Add support for GPIO names
gpio: 104-idi-48: Add support for GPIO names
gpio: 104-dio-48e: Add support for GPIO names
gpio: ws16c48: Remove unnecessary driver_data set
gpio: gpio-mm: Remove unnecessary driver_data set
gpio: 104-idio-16: Remove unnecessary driver_data set
...
The PCI BAR0 and BAR1 for the PCI-IDIO-16 hold information for the PLX
9052 bridge chip on the device. The PCI BAR2 holds the necessary base
address for I/O control of the PCI-IDIO-16. This patch corrects the PCI
BAR index mismatch for the PCI-IDIO-16 GPIO driver.
Fixes: 02e74fc040 ("gpio: Add GPIO support for the ACCES PCI-IDIO-16")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES PCI-IDIO-16 has a PCI device ID code of 0x0DC8. It is
incorrect to use the PCI device ID code of the ACCES PCI-IIRO-8
(0x0F00). This patch fixes the said PCI device ID code mismatch.
Fixes: 02e74fc040 ("gpio: Add GPIO support for the ACCES PCI-IDIO-16")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Create a debugfs directory for every mockup chip and a single file
for every line. Writing (0 or 1) to these files allows the user to
inject line events (falling or rising edge respectively).
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setup a dummy irqchip that will allow us to inject line events for
testing purposes.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to allow testing line lookup by name from user space, add
a new boolean parameter that indicates whether we want the lines to
be named. The name is created by concatenating the chip name and the
line offset value.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Moving a couple of lines around allows us to shrink the code a bit
while keeping the same functionality.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The following patch tries to improve the readability of the mockup
driver.
The driver is called gpio-mockup, so add the same prefix to all
functions and structures.
Add some newlines and use a temporary pointer in gpio_mockup_add().
Drop the name of the direction enum and rename the enum values to
better reflect their purpose.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES PCI-IDIO-16 device provides 32 lines of digital I/O (16 lines
of optically-isolated digital inputs for AC and DC control signals, and
16 lines of solid state switch digital outputs). An interrupt is
generated when any of the inputs change state (low to high or high to
low). Input filter control is not supported by this driver, and input
filters are deactivated by this driver.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
1736f75d35 is a (v2) patch which had
unresolved review comments[1]. Address the comments by removing the use
of macros from the consumer header (this patch represents the diff
between v2 and v3[2]).
[1] https://lkml.org/lkml/2017/1/26/337
[2] https://lkml.org/lkml/2017/1/26/786
Fixes: 1736f75d35 ("gpio: aspeed: Add banks Y, Z, AA, AB and AC")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_fwnode_get_gpiod_from_child() currently allows GPIO users to
request a GPIO that is defined in a child fwnode instead of directly in
the device fwnode.
Extend this API by adding the devm_fwnode_get_index_gpiod_from_child()
helper which does the same except you can also specify an index in case
the 'xx-gpios' property describe several GPIOs.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename devm_get_gpiod_from_child() into
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver now using devm_regmap_init/devm_regmap_init_i2c, so it needs
to select REGMAP/REGMAP_I2C accordingly.
Fixes: ("3d84fdb3f0b5 gpio: mcp23s08: use regmap")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch sets the gpio_chip names option with an array of GPIO line
names that match the manual documentation for the WinSystems WS16C48.
This should make it easier for users to identify which GPIO line
corresponds to a respective GPIO pin on the device.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch sets the gpio_chip names option with an array of GPIO line
names that match the manual documentation for the Diamond Systems
GPIO-MM. This should make it easier for users to identify which GPIO
line corresponds to a respective GPIO pin on the device.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch sets the gpio_chip names option with an array of GPIO line
names that match the manual documentation for the ACCES 104-IDIO-16.
This should make it easier for users to identify which GPIO line
corresponds to a respective GPIO pin on the device.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch sets the gpio_chip names option with an array of GPIO line
names that match the manual documentation for the ACCES 104-IDI-48.
This should make it easier for users to identify which GPIO line
corresponds to a respective GPIO pin on the device.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch sets the gpio_chip names option with an array of GPIO line
names that match the manual documentation for the ACCES 104-DIO-48E.
This should make it easier for users to identify which GPIO line
corresponds to a respective GPIO pin on the device.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting driver_data was necessary to access private data in the
ws16c48_remove function. Now that the ws16c48_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting driver_data was necessary to access private data in the
gpiomm_remove function. Now that the gpiomm_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting driver_data was necessary to access private data in the
idio_16_remove function. Now that the idio_16_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting driver_data was necessary to access private data in the
idi_48_remove function. Now that the idi_48_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting driver_data was necessary to access private data in the
dio48e_remove function. Now that the dio48e_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use regmap API to save some lines of codes and have
debugfs support for all of the MCP's registers.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call and
request_irq call with the devm_gpiochip_add_data call and
devm_request_irq call respectively. In addition, the ws16c48_remove
function has been removed as no longer necessary due to the use of the
relevant devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call with
the devm_gpiochip_add_data call. In addition, the gpiomm_remove function
has been removed as no longer necessary due to the use of the relevant
devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call and
request_irq call with the devm_gpiochip_add_data call and
devm_request_irq call respectively. In addition, the idio_16_remove
function has been removed as no longer necessary due to the use of the
relevant devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call and
request_irq call with the devm_gpiochip_add_data call and
devm_request_irq call respectively. In addition, the idi_48_remove
function has been removed as no longer necessary due to the use of the
relevant devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call and
request_irq call with the devm_gpiochip_add_data call and
devm_request_irq call respectively. In addition, the dio48e_remove
function has been removed as no longer necessary due to the use of the
relevant devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently we already have two pin configuration related callbacks
available for GPIO chips .set_single_ended() and .set_debounce(). In
future we expect to have even more, which does not scale well if we need
to add yet another callback to the GPIO chip structure for each possible
configuration parameter.
Better solution is to reuse what we already have available in the
generic pinconf.
To support this, we introduce a new .set_config() callback for GPIO
chips. The callback takes a single packed pin configuration value as
parameter. This can then be extended easily beyond what is currently
supported by just adding new types to the generic pinconf enum.
If the GPIO driver is backed up by a pinctrl driver the GPIO driver can
just assign gpiochip_generic_config() (introduced in this patch) to
.set_config and that will take care configuration requests are directed
to the pinctrl driver.
We then convert the existing drivers over .set_config() and finally
remove the .set_single_ended() and .set_debounce() callbacks.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is less straight-forward than one would hope, as some banks only
have 4 pins rather than 8, others are output only, yet more (W and
X, already supported) are input-only, and in the case of the g4 SoC bank
AC doesn't exist.
Add some structs to describe the varying properties of different banks
and integrate mechanisms to deny requests for unsupported
configurations.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Aspeed SoCs have more GPIOs than can be represented with A-Z. The
documentation uses two letter names such as AA and AB, so make the names
a three-character array in the bank struct to accommodate this.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Exar XR17V352/354/358 chips have 16 multi-purpose inputs/outputs which
can be controlled using gpio interface.
Add the gpio specific code.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The WinSystems WS16C48 provides registers where 8 lines of GPIO may be
set at a time. This patch add support for the set_multiple callback
function, thus allowing multiple GPIO output lines to be set more
efficiently in groups.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Diamond Systems GPIO-MM series provides registers where 8 lines of
GPIO may be set at a time. This patch add support for the set_multiple
callback function, thus allowing multiple GPIO output lines to be set
more efficiently in groups.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-IDIO-16 series provides registers where 8 lines of GPIO
may be set at a time. This patch add support for the set_multiple
callback function, thus allowing multiple GPIO output lines to be set
more efficiently in groups.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-DIO-48E series provides registers where 8 lines of GPIO
may be set at a time. This patch add support for the set_multiple
callback function, thus allowing multiple GPIO output lines to be set
more efficiently in groups.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Dmitry Torokhov
Hans de Goede
Robert Middleton
Phil Reid
Arnd Bergmann
Dan Carpenter
Thor Thayer
Linus Torvalds
William Breathitt Gray
Bartosz Golaszewski
Linus Walleij
Andrew Jeffery
Boris Brezillon
Axel Lin
Christophe JAILLET
Sebastian Reichel
Mika Westerberg
Joel Stanley
Sudip Mukherjee